Manager operating guide LED RKP V7.

0
How to change or delete
AvantiXP XL8 How to view the
a code
AvantiLC Avanti 8 Quick Set
This feature allows the panel to be SET so that it overrides
alarm log
the programmed exit time. Entering an access code, From DAY mode ¯
selecting Program A / B or * and then pressing ¯will
From DAY mode ¯ Enter Manager Code
How to set your cause the panel to SET within 2 seconds.
system and if you wish ? ? ? ?
On board PA Enter Manager Code
omit a zone Simultaneously depressing key’s 4 and 8 will activate a PA ? ? ? ? Enter 1
thus creating a full alarm condition. This feature can be
From DAY mode used when the system is in DAY mode or SET Enter 2 Next select code to be changed
Enter Manager Code Fault during setting
? ? ? ? If the system is unable to SET then the internal sounders After selecting Alarm Log the zone, 1 User 1 access code
will make an error tone. The fault on the system will be PA and Tamper LED’s will show the
A indicated by the relevant zone/PA/Tamper LED being lit. If latest event 2 User 2 access code
Select a zone LED is lit then ensure that all windows and doors A flashing LED indicates the zone that 3 User 3 access code
Program B are closed and the zone is clear. If the fault persists then it was first activated.
* may be possible to omit the zone. Any other LED lit was activated after 4 User 4 access code
System Faults the first event but before system 5 Holiday code
The panel will now set. If after entering your code the Tamper LED is flashing unset 2
there may be a System fault. Re-enter your code. there 1 2 3 4 5 6 7 8 6 Manager code
To omit a zone press Z are 4 possible faults indicated by the Zone LEDS flashing.
Day 7 Duress code
And then the zones you wish Z1 Mains Fail Z2 Tel Line Fail
to omit PA Next
Z3 Battery Low Z4 Service Due
Tamper
Entering your code again will allow you to override the To navigate through the log Enter 4 new digits
How to unset your fault, but you must inform the Engineer. ? ? ? ?
system 1 Jump to oldest event
Alarm Activation or
2
If the system has been activated then an access code 2 Move one event older
needs to be entered. To reset the system all that is Delete access code
Enter Manager Code 3 Move one event newer
required is to re -enter an access code. If your system is *
? ? ? ? monitored you should contact your engineer to reset the
4 Jump to newest event Then
panel.
The panel is now in DAY. Holiday Access Code Z Manager menu A
The purpose of this code is to allow access to the property To accept
whilst the manager is absent. The Holiday Access Code is Maximum of 16 events can be viewed B To abort
How to program programmed by the Manager and is only valid until the
chime on any Manager USE’s the system. At this point the Holiday Z Manager menu
zone Access Code becomes invalid and is no longer accepted by How to authorise
the control panel.
Engineer access How to test your
From DAY mode User Codes/
alarm system
A User can perform the same operations as a Manager
¯ except they are unable to View the Alarm Log, access the
Enter Manager Code Test Menu.
From DAY mode ¯ From DAY mode ¯
Authorize engineer (user)
? ? ? ? Enter Manager Code Enter Manager Code
A User simply enters their access code then press Z to ? ? ? ?
Select ¯ quit from user access, the engineer will then promptly ? ? ? ?
Toggle zones by enter the engineer code. A timer will then start allowing 3
hours engineer access. Enter 3 Enter 9 Test Menu
pressing KEYs 1-8
Z 1 Switch bell on 6 Enter walk test
A To accept Installation Company contact and telephone No Followed by
2 Switch strobe on Z Exit walk test
B To abort This returns you to DAY 2
Keypad will now give a & allows 3 hours 3 Switch speakers on 9 Zone status
011003

confirmation beep and the Engineer access 0 Switch outputs off Z Manager menu
chime zone numbers will be lit