Installation Manual RCUXXYY

EAE KNX ROOM CONTROLLER UNIT RCUXXYY R

Technical Data

Type of protection IP 20 EN 60 529

Safety Class II EN 61 140
Power Supply 21V… 30V DC, SELV
Connections Screw terminals
0,05…3,31 mm² solid and stranded wire
0,05…3,31 mm² stranded wire with ferrule
-0.8 Nm Max. Tightening torque
KNX Bus connection terminal
Input up to 18 channels independent
Output up to 20 channels / 5 groups
Connection Switching voltage
1. Physical Address Label 277/440V AC; 50/60 Hz
2. KNX programming button Switching capacity
3. KNX programming LED 277 V AC 16A / AC 1
4. KNX connection Fluorescent lighting load
5. Indicator LEDs 16 AX/250 VAC EN 60 669-1
6. Manual control channel selection buttons Output Life Mechanical life > 3 x 106
7. Manual control button Installation 35 mm mounting rail
8. Manual control up/down, on/off button EN 60 715
9. Inputs Temperature range Ambient -5° C + 45° C
Storage -25° C + 55° C
General Description Transport -25° C + 70° C
Humidity Max. Air humidity
95 % no moisture condensation
Dimensions 66 x 179 x 90 mm h x L x W
Weight 0.8 kg
Box Plastic, polycarbonate, color grey
CE In accordance with the EMC guideline and low voltage

Technical Drawings

Device has 20 outputs which can be programmed via ETS4 or above. Outputs contain 5
independent outputs. (AB, CD, EF, GH, IJ) Operating method for each relay group can be
configured as like below.
• Switching Output x4
• AC Blind x2
• DC Blind x1
• Two Point Valve x2
• Three Point Valve x2

Device has 18 independent Input Channels. Input Channels may operate the actions below as
well as Universal Interface.
• Switching
• Dim Control
• Blind Control
• Value and Priority Sending
• Scene Control
• Pulse Counter

All of input configurations can be operated independently.

Operation and Indication Elements Commissioning

-Programming LED(3) Device product file “.knxprod” must be imported to the ETS product catalog. Product file can
Programming LED will be indicated if the programming button pressed. This button is used to be found in our website. www.eaetechnology.com
download individual address to the device. Physical addressing and programming can be done ETS4 or higher.
-Manual Control Channel Selection Buttons (6)
This button can be used to select relay or relay groups.
A detailed information about parameter configuration can be found in Product Manual
-Manual Control Button (7)
of device.
This button is used to switch to manual mode in device.
-Manual Control Up/Down, On/Off button (8)
This button is used to control the relay or relay groups. Installation and commissioning of device may only be implemented by trained
electricians. The relevant standards, directives, regulations and instructions must be observed
when planning and implementing the electrical installation.
Installation
Device is manufactured according to EN 60 715 standard. It is compatible with 35 mm DIN rail. - When connecting the device make sure that the device can be isolated!
- Protect the device against moisture, dirt and damage during transport, storage and
Cleaning operation!
If device becomes dirty, only a dry cloth can be used for cleaning. It is not suitable to use wet - Do not operate the device out of the specified technical data which is stated.
cloths, caustics and solvents. - The device may only be operated in closed enclosures such as distribution boards.

© EAE Technology www.eaetechnology.com

İkitelli Org. San. Bölgesi, Ziya Gökalp Mah. Eski Turgut Özal Cad.
No: 20, 34490 Başakşehir/İstanbul Tel: +90 212 549 97 13
 Installation Manual RCUXXYY
EAE KNX ROOM CONTROLLER UNIT RCUXXYY R

Room Control Unit 2018 Room Control Unit 1212

Room Control Unit 1616 Room Control Unit 0808

© EAE Technology www.eaetechnology.com

İkitelli Org. San. Bölgesi, Ziya Gökalp Mah. Eski Turgut Özal Cad.
No: 20, 34490 Başakşehir/İstanbul Tel: +90 212 549 97 13