Question 01

#Q. Consider the following CT system with an input x(t) and output y(t).
dx t
System P : y t =
dt

System Q : y(t) = ex(t)

System R : y(t) = 3x(t)
System S : y(t) = 3x(t) + 5
Which of the above system is/are linear

A P, R, S B Only R

C P and R D All are linear

Question 02

#Q. Consider the AM system with following input-output relationship.

y(t) = [1 + 0.2x(t)] cos(2π × 108 t)
where x(t) is the input and y(t) is output. Which of the following
statement is not true?

A The system is linear

B Modulation index is 0.2

C System is non-linear

D Both (B) and (C)

Question 03

#Q. Consider the following systems with an input x(t) and output y(t) The
systems are
S1 : y(t) = x2(t)
S2 : y(t) = t2 x(t)
S3 : y(t) = x(t2)
S4 : y(t) = x(– t)
The time-invariant systems are
A S1 and S3 B S1 and S4

C only S1 D S1, S3 and S4

Question 04

#Q. For an input x(t), the output y(t) of a modulator is given by y(t) = x(t) cos
2πfct where fc is the carrier frequency. The system is

A dynamic, non-linear and time-invariant

B static, linear and time-variant

C static, non-linear and time-invariant

D dynamic, linear and time-variant

Question 05

#Q. A CT system has the input output relationship y(t) = x(5t). The system is

A static, linear and time-variant

B dynamic, linear and time-variant

C dynamic, linear and time-invariant

D static, linear and time-invariant

Question 06

#Q. Which of the following system is causal ? {x(t) is input, y(t) is output}

A y(t) = 2x2(t) + x(t – 4)

B y(t) = x(t – 4) + x(4 – t)

2t
C y t = ‫׬‬−∞ x τ dτ

D none of these
Question 07

#Q. The equation y(t) = 4x(t) + 7 describes a system with an input x(t) and
an output y(t). The system is

A Linear and invertible

B non-linear and non-invertible

C linear and non-invertible

D non-linear and invertible

Question 08

#Q. Let P be linearity, Q be time-invariance R be causality and S be stability.

A CT system is described by following relationship
y(t) = tx(t)
where x(t) is input and y(t) is output. The above system has the
properties-
A P, Q, R

B P, R, S

C P, R

D P, Q, R, S
Question 09

#Q. Consider a rectangular pulse shown in the figure below

The graph for y(t) = x(t) * x(t) will be

A B

C D
Question 10

#Q. The convolution of a CT signal with itself is shown in figure

The signal is

A B

C D
Question 11

#Q. Two CT signals are given in the figure below

The convolution y(t) of above two signals for an interval 0  t < 1 is

A 0

B t+1

C 1–t

D –1 – t
Question 12

#Q. For a unit step signal u(t), the convolution u(t) * u(t) equals to

A t2u(t)

B u(t)

C tu(t)

D 2u(t)
Question 13

#Q. For an input x(t) = e–2(t – 3)u(t), output of a system having impulse
response h(t) = e–tu(t) will be

A e6(e–t – e–2t)u(t)

B e6(e–2t + e–t)u(t)

C e6(–e–t + e–2t)u(t)
𝑒6 –t
D (e – e–2t)u(t)
3
Question 14

#Q. The figure shown two signal x(t) and h(t) as

Which of the waveforms in the option corresponds to convolution x(t) *

h(t)?
A B

C D
Question 15

#Q. Which of the following convolution is not correct?

A x(t) * (t) = x(t)

B x(t) * (t – t0) = x(t0)

t
C x t ∗ u t = ‫׬‬0 x τ dτ

D None of these
Question 16
#Q. The input-output relationship of a CT system is given as
t
y t = ‫׬‬−∞ t − λ + 2 x λ dλ
The impulse response of the system is

A B

C D
Question 17

#Q. In the system shown below x(t) = u(t – 2) and h(t) = u(t – 4) The plot for
output y(t) will be

A B

C D
Question 18

#Q. The input x(t) and impulse response h(t) of an LTI system shown in
figure are
x(t) = (t – 1) – 2(t + 1)
h(t) = u(t + 1) – u(t – 3)
The waveform which corresponds to output y(t) will be
A B

C D
Question 19

#Q. What function convolved with –3 cos t would produce 6 sin t?

A 3(t + π)
π
B 3δ t +
2
π
C 2δ t +
2
π
D 2δ t –
2
Question 20

#Q. A signal x(t) = 𝑒 𝑗𝜔0𝑡 is convolved with another signal h(t) shown in
figure. Let y(t) = x(t) * h(t), then for what value of 0, y(0) = 0?

A π
π
B 2
π
C 2

D 2π
Question 21

#Q. Two signals x(t) and h(t) and their convolution are defined as follows

x(t) = 0, |t| > T1

h(t) = 0. |t| > T2

x(t) * h(t) = 0 |t| > T3

T3 will be

A T3 > |T1 – T2| B T3 > |T1 + T2|

C T3 < |T1 + T2| D T3 = max(T1, T2)

Question 22

#Q. Which of the following impulse response is causal?

A h(t) = (t – 2)

B h(t) = (t + 0.01)

C h(t) = u(t – 4) – u(t + 4)

D h(t) = u(–t + 1)
Question 23

#Q. Let x(t) and y(t) are the input and output of an LTI system described as
t
y t =ධ e−2 t−τ x τ − 1 dτ
−∞

The system is

A non-causal and stable

B causal and stable

C causal and unstable

D non-causal and unstable

Question 24

#Q. A system with the impulse response h(t) = 6(t + 5)

A has memory and is stable

B does not have memory and is unstable

C has memory and is unstable

D none of above
Question 25

#Q. The impulse response of four CT systems S1 S2 S3 and S4 are given

respectively as
h1(t) = (t)
1
h2(t) = e−tΤτ u t
τ
h3(t) = u(t) – u(t – 2)
h4(t) = cos(100t) u(t)
Which of these system is not BIBO stable
A S1

B S2

C S3

D S4
Question 26

#Q. A system defined by its impulse response h(t) = u(t + 1)-u(t – 3) is

A causal and stable

B causal and unstable

C non-causal and stable

D non-causal and unstable

Question 27

#Q. A causal system has the following impulse response h(t) = [2e–3t – e–2t]
u(t). For an input x(t) = u(t), the output is
1 −2t 2
A e − e−3t u t
2 3
1 2 1
B − 𝑒 −3𝑡 + 𝑒 −2𝑡 𝑢 𝑡
6 3 2

C (4e–2t – 6e–3t) u(t)

D (4e–2t – 6e–3t + 6) u(t)

Question 28

#Q. The impulse response of an LTI system is shown in the figure

The step response is

A 2 + et – e–t

B et u(–t + 1) + 2 – e–t

C et u(–t + 1) + (2 – e–t) u(t)

D et + [2 – e–t – et] u(t)

Question 29

#Q. The impulse response of the system shown in figure is

1
A u t −δ t−τ
τ
1
B 𝑢 𝑡 −𝑢 𝑡−𝜏
𝜏
1
C 𝑢 𝑡−𝜏
𝜏
1
D δ t −δ t−τ
τ
Question 30

#Q. The continuos time convolution y(t) = [u(t) – u(t – 2)] * u(t) is

A tu(t) + (2 – t) u(t – 2)

B (2 – t) u(t) + tu(t – 2)

C tu(t) + (t – 2) u(t – 2)

D (t – 2) u(t) + tu(t – 2)
Question 31

#Q. The continuous time convolution integrals y t = e−3t u t ∗ u t + 3 is

1
A 1 − e−3 t+3 u t+3
3
1
B 1 − e−3 t+3
u t
3
1
C 1 − e−3t u t
3
1
D 1 − e−3t u t + 3
3
Question 32

#Q. The continuous time convolution y(t) = cos π t[u(t + 1) – u(t – 1)] * u(t) is

sinπt
A u t+1 −u t−1
π
sinπt
B u(t – 1)
π
sinπt
C u(t + 1)
π
sinπt
D u(t)
π
Question 33

#Q. The continuous time convolution integrals y(t) = u(t) * h(t), where
e2t , t < 0
h t = ቊ −3t
e , t≥0

1 −2t 5 1
A e u −t − 1 + − e−3t u −t
2 6 3
1 2t 5 1
B e u −t − 1 + − e−3t u −t
2 6 3
1 2t 1
C 2
e +
6
5 − 3e2t − 2e−3t u t
1 2t 1
D 2
e +
6
5 − 3e2t − 2e−3t u – t
Question 34

#Q. Figure given below shows the input x(t) to an LTI system and impulse
response h(t) of the system.
The output of the system is zero every where except for the

A 0<t<5

B 0<t<8

C 1<t<5

D 1<t<8
Question 35

Common Data
Suppose that
1, 0 ≤ t ≤ 1
x t =ቊ
0, elsewhere
t
h t =x , where0 < a ≤ 1.
a
#Q. The y(t) = x(t) * h(t) is
A B

C D
Question 36

Common Data
Suppose that
1, 0 ≤ t ≤ 1
x t =ቊ
0, elsewhere
t
h t =x , where0 < a ≤ 1.
a
#Q. If dy(t)/dt contains only three discontinuities, the value of a is

A 1 B 2

C 3 D 0
Question 37

#Q. An LTI system has impulse response h(t)= (2t – 1) then it

A delays the single

B samples the input signal

C attenuates the input signal

D delays and attenuates the signal

Question 38

#Q. An LTI system has the impulse response shown below.

If the system is excited by an input x(t) = (t – 1) + (1 – 3), then output
y(t) will be
A B

C D
Question 39

#Q. Two CT signals x(t) and h(t) are shown in figure below.
Which of the following plot represents y(t) = x(t) * h(t)
A B

C D
Question 40

#Q. The impulse response of an LTI system is h(t) = e–|t|. The step response is

A 2 + et – e–t

B et u(–t + 1) + 2 – e–t

C et u(–t + 1) + [2 – e–t]u(t)

D et + [2 – e–t – et]u(t)
Question 41

#Q. The impulse response of an LTI system is h(t) = u(t) – u(t – 4) The step
response is

A tu(t) + (4 – t) u(t – 4)

B tu(t) + (1 – t) u(t – 4)

C 1+t

D (1 + t) u(t)
Question 42

#Q. The impulse response of a continuous-time LTI system is

t−100
h t = 2e−t −e 100 u t
The system is

A causal and stable

B causal but not stable

C stable but not causal

D neither causal nor stable

Question 43

#Q. The impulse response of an LTI system is h(t) = e–6|t|. The system is

A causal and stable

B causal but not stable

C stable but not causal

D neither causal nor stable

Question 44

#Q. The impulse response of an LTI system is h(t) = e–6t u(3 – t). The system is

A causal and stable

B causal but not stable

C stable but not causal

D neither causal nor stable

Question 45

#Q. The impulse response of an LTI system is h(t) = e–4tu(t – 2) The system is

A causal and stable

B causal but not stable

C stable but not causal

D neither causal nor stable

Question 46

#Q. Consider the impulse response of two LTI system

S1 : h1(t) = e–(1 – 2j)t u(t)
and S2 : h2(t) = e–t cos2tu (t)
The stable system is

A S1

B S2

C Both S1 and S2

D None
Question 47

#Q. The impulse response of two system is

h1(t) = u(t) – u(t – 4)
t –2
and h2(t) = rect
4

If these system are cascaded then response of the total system is

A B

C D
Question 48

#Q. If cross – correlation between two real signals x(t) and y(t) is rxy(t) the
true statement is

A rxy(t) = x(t) * y(t)

B rxy(t) = x(–t) * y(t)

C rxy(t) = x(t) * y(–t)

D rxy(t) = x(–t) * y(–t)

Question 49

𝑡𝑘
#Q. The convolution of two signals x(t) = tu(t) and x2(t) = u(t) is u(t) such
𝑘

that the value of k is __________.

Question 50

#Q. Let y(t) = 𝑒 −𝑡 𝑢(𝑡) ∗ 𝛿(𝑡 − 1) then the value of y(2) is _______
Question 51

#Q. The impulse response of an LTI system is h(t) = t2 u(t), the step response

𝑡𝑘
will be u(t) such that the value of k is ______
𝑘
Question 52

#Q. The auto correlation function Rxx(𝜏) of a signal x(t) = e–t u(t) is ke–|𝜏|
where the constant k is ______
Question 53

#Q. The response of an LTI system for an input x1(t) = u(t) – u(t – 1) is g(t).
What will be the response of the system for an input x2(t) shown in
figure below ?
Question 54

𝜋𝑡
#Q. A CT signal is expressed as g(t) = 4sin * 𝛿(t – 3). What is the value of
8

g(–1) ?
Question 55

𝑡
#Q. If a CT signal is given as x(t) = 5rect * [𝛿(t + 1) + 𝛿(t)], then value of
2

1
x is _______
2
Question 56

𝑡
#Q. The value of CT signal x(t) = 8tri * 𝛿(t – 2) at t = 1 sec is _______.
4
Question 57

#Q. The impulse response of an LTI system is h(t) = u(t). If the step response
of the system is s(t) then s(2) = __________
Question 58

#Q. The impulse response of a system is h(t) = 𝛿(t – 0.5). If two such systems
are cascaded, the impulse response of the overall system will be
k𝛿(t – k) such that the value of k is ________.
Question 59

#Q. Consider the two identical LTI system cascaded as follows

Impulse response of the each systems is h1(t) = h2(t) = e–2t u(t). If the
ℎ(𝑡)
impulse response of the overall system is h(t), then | = ______
ℎ1 (𝑡) 𝑡=2
Question 60

#Q. The system having input output relationship y(t) = x(2t) is

A static

B linear

C both (A) & (B)

D causal
Question 61

#Q. When a unit step function is applied as the input to an LTI system, the
output is a bounded signal. Which of the following statement is correct?
A The system is definitely unstable

B The system is not definitely stable

C The system is not necessarily stable

D None of the above

Question 62

#Q. If x1(t) = A[u(t) – u(t – 4)] and x2 (t) = B[u(t) – u(t – 2)] then convolution
x1 (t) * x2 (t) is a

A rectangular pulse

B triangular pulse

C trapezoidal pulse

D sinc pulse
Question 63

#Q. x1(t) = A[u(t) – u(t – 2)] and x2(t) = B[u(t) – u(t – 2)] then convolution
x1(t) * x2(t) is a
A trapezoidal pulse

B rectangular pulse

C triangular pulse

D sinc pulse
Question 64

#Q. The convolution of two causal signals x1(t) and x2(t) can be represented
as
𝑡
1. ‫=𝜏׬‬0 𝑥1 (𝜏)𝑥2 (𝑡– 𝜏)𝑑𝜏 A 1 only
𝑡
2. ‫=𝜏׬‬0 𝑥2 (𝜏)𝑥1 (𝑡– 𝜏)𝑑𝜏 B 2 only
𝜏
3. ‫=𝑡׬‬0 𝑥1 (𝑡)𝑥2 (𝜏– 𝑡)𝑑𝑡 C 1 and 2 only
𝜏
4. ‫=𝑡׬‬0 𝑥2 (𝑡)𝑥1 (𝜏– 𝑡)𝑑𝑡 D 1, 2, 3 and 4
Question 65

#Q. The LTI system with an impulse response h(t) = e–2t, – ∞ < t < ∞ is

A causal and unstable

B non-causal and stable

C non-causal and unstable

D causal and stable

Question 66

#Q. Two LTI system with impulses responses h1(t) and h2(t) are connected
in parallel, the impulse response of the overall system will be

ℎ 1 𝑡 ℎ2 𝑡
A
ℎ1 𝑡 + ℎ2 𝑡

B h1(t) * h2(t)

C h1(t) + h2(t)

D h1(t) h2(t)
Question 67

#Q. The auto-correlation function R(𝜏) of a signal x(t) is maximum at

A 𝜏=∞

B 𝜏=0

C depends on x(t)

D None of these
Question 68

#Q. The auto-correlation R(𝜏) of a signal x(t) at = 0 is equal to

A Power

B Energy

C Any of the above (A) or (B) depending upon the signal

D None
Question 69

#Q. The auto-correlation function R(𝜏) is

A Even function of 𝜏

B Odd function of 𝜏

C Both (A) and (B)

D None
 Answer Keys

1 (C) 2 (D) 3 (C) 4 (B) 5 (B)

6 (A) 7 (D) 8 (C) 9 (B) 10 (C)
11 (C) 12 (C) 13 (A) 14 (D) 15 (B)
16 (C) 17 (C) 18 (B) 19 (C) 20 (D)
21 (B) 22 (A) 23 (B) 24 (A) 25 (D)
26 (C) 27 (B) 28 (D) 29 (B) 30 (A)
31 (A) 32 (A) 33 (C) 34 (D) 35 (A)
36 (A) 37 (D) 38 (D) 61 39 (B) 40 (D)
41 (A) 42 (B) 43 (C) 44 (D) 45 (A)
46 (C) 47 (B) 48 (C) 74 49 (2) 50
(0.3679)
 Answer Keys

51 (3) 52 (0.5) 53 (2) 54 (–4) 55 17 (5)

56 (6) 57 (2) 58 (1) 59 (2) 60 (B)
61 (C) 62 (C) 63 (D) 64 (D) 65 (C)
66 (D) 67 (B) 68 (C) 69 (A)