Scribd
Upload
21 views19 pages

Virtual Lab

Uploaded by

pavitra.bijyt
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
21 views19 pages

Virtual Lab

Uploaded by

pavitra.bijyt
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

Virtual Lab

(Through Online Mode)

Experiment Name Date Signatur


S.No e

1. Intro to MOS-Capacitor Tool (: https://nanohub.org/)

. Biosensor Lab: Planar Sensor, Nano-wire Sensor, and Nanodot


2.
Sensor (: https://nanohub.org/)

Biosensor Lab: Double Gate FET Sensor, Extended Gate FET ph


3. Sensor, Extended Gate FET Bio-Sensor and Flexure FET Sensor (:
https://nanohub.org/)

Simulate 2-D electrons transport in CNTFET


4.
(: https://nanohub.org/)

5. Amorphous Silicon Generator (: https://nanohub.org/)

Electrostatic Properties Simulation of Layered 2D Material


6.
(: https://nanohub.org/)

7. Graphene Nanopore Drilling (: https://nanohub.org/)

PV parameters calculator using i-v and EQE data


8.
(: https://nanohub.org/)

Half wave Rectifier without Filter, 2. Full wave Rectifier without


9. Filter, 3. Clipping (Limiting) Circuits, 4. Clamper Circuit
(http://vlabs.iitkgp.ac.in/psac/newlabs2020/ssds/#
Experiment No 1

Aim: Intro to MOS-Capacitor Tool

Online Platform used: NANOHUB online electronic simulation tools

Introduction:

Understanding the effect of silicon doping, oxide (SiO2) thickness, gate type
(n+poly/p+poly), and semiconductor type (n-type/p-type) on the flatband voltage,
threshold voltage, surface potential and oxide voltage of a MOS-Capacitor.

Procedure for online simulation:

Step 1. Select “MOS-Capacitor Tool” from the list of Tools in https://nanohub.org/

2. Double click on Launch Tool


3. Now Simulate to find the final result:
=================================================
=Intro to MOS-C Tool Simulation Results
=================================================
MOS Configuration
Gate Type: n+poly
Silicon Doping Type: p-type

Doping: NA = 1e+15 (/cm3)

Oxide Thickness: 5e-06 (cm)


---------------------------------------------------------
Ei-Ef= 0.298646 (eV)
Oxide Capacitance: 6.903e-08 (F/cm2)
Flatband Voltage: -0.858646 (V)
---------------------------------------------------------
-Threshold Condition
---------------------------------------------------------
Threshold Voltage: -0.0558244 (V)
Surface Voltage: 0.597291 (V)
Oxide Voltage: 0.20553 (V)
Maximun Depletion Width: 8.86734e-05 (cm)

Capacitance at Threshold Voltage:


High Frequency -> 1.01333e-08 (F/cm2)
Low Frequency -> 6.903e-08 (F/cm2)
---------------------------------------------------------
-MOS-Capacitor Data
----------------------------------------------------
Vg(V) Wdep(cm) PhiS(V) Vox(V)
-0.858646 0 0 0
-0.698081 3.31841e-05 0.083649 0.0769153
-0.537517 5.15284e-05 0.201694 0.119434
-0.376953 6.58234e-05 0.329125 0.152568
-0.216389 7.79513e-05 0.461579 0.180678
-0.0558244 8.86734e-05 0.597291 0.20553
Experiment No 2

Aim. . Biosensor Lab: Planar Sensor, Nano-wire Sensor, and Nano dot Sensor

Platform used: NANOHUB online electronic simulation tool

BioSensorLab is a tool to evaluate and predict the performance parameters of


Biosensors.

BioSensorLab is a tool to evaluate and predict the performance parameters of a label-free,


electronic biosensor (see figure). The sensor basically consist of a field effect device, whose
surface is functionalized with capture probe (receptor) molecules. Some of the target
molecules, which are introduced to the system, diffuse through the solution and reach the
field effect device and get captured by the receptors thereby binding them close to the surface

Online Platform: https://nanohub.org/

Procedure: Select “Biosensor Lab Tool” from the list of Tools in


Experiment No 3

Aim: Biosensor Lab: Double Gate FET Sensor, Extended Gate FET ph Sensor, Extended
Gate FET Bio-Sensor and Flexure FET Sensor (: https://nanohub.org/)

Platform used: NANOHUB online electronic simulation tool

Introduction: BioSensorLab is a tool to evaluate and predict the performance


parameters of a label-free, electronic biosensor (see figure). The sensor basically
consist of a field effect device, whose surface is functionalized with capture probe
(receptor) molecules. Some of the target molecules, which are introduced to the
system, diffuse through the solution and reach the field effect device and get
captured by the receptors thereby binding them close to the surface. Many bio-
molecules carry an electrostatic charge under normal physiological conditions.

Procedure for online simulation :

Step 1. Select “BioSensorLab” from the list of Tools in https://nanohub.org/


Experiment No 4
Aim: Simulate 2-D electrons transport in CNTFET
(: https://nanohub.org/)

Online Platform used: NANOHUB online electronic simulation tools

Introduction:

Simulates ballistic transport properties in 3D Carbon NanoTube Field Effect


Transistor (CNTFET) devices
CNTFET can currently simulate the impact of quantum mechanical size
quantization and phase coherence in zigzag nanotubes with both planar and coaxial
exterior architectures. The application is based on the Non-Equilibrium Greens’
Function (NEGF) techniques using a pz-orbital nearest-neighbor tight binding. Full
three-dimensional (3D) electrostatics has been captured by the Finite-Element-
Method (FEM) of solving the Poisson Equation.

Procedure for online simulation:

Step 1. Select “CNTFET Lab” from the list of Tools in https://nanohub.org/


Experiment No. 5

Aim : Amorphous Silicon Generator (: https://nanohub.org/)

Online Platform used: NANOHUB online electronic simulation tools

Introduction:
This tool generates realistic random-network models of a-Si with periodic boundary
conditions.
A-Si-H Generator

Procedure for online simulation:

Step 1. Select “Amorphous Silicon Generator” from the list of Tools in


https://nanohub.org/
Experiment No 6

Aim: Electrostatic Properties Simulation of Layered 2D Material


(: https://nanohub.org/)

Online Platform used: NANOHUB online electronic simulation tools

Introduction:
Simulate charge carrier density, potential drop and energy band diagram across
any vertical 1D cross-section in a layered heterostructure of 2D semiconductors,
graphene and metals.

Procedure for online simulation:

Step 1.
Select “Electrostatic Properties Simulation of Layered 2D Material Device” from the
list of Tools in https://nanohub.org/
Experiment No 7

Aim: Graphene Nanopore Drilling (: https://nanohub.org/)

Online Platform used: NANOHUB online electronic simulation tools

Introduction:
Drilling a nanopore in graphene by Si-nanoparticle bombardment
This is an MD-based tool drilling a nanopore in graphene by using Si-nanoparticle
bombardment. The user adjustable parameters are particle size (Å), initial position of
nanoparticle (Å), incident speed of particle (km/s), simulation timestep (fs), total number
of simulation steps, number of dumping frequency. After the MD simulation is done, the
use can run the post-processing code to quantify the pore formation.

Procedure for online simulation:

Step 1. Select “Graphene Nanopore Drilling” from the list of Tools in


https://nanohub.org/
Experiment No 8

Aim: PV parameters calculator using I-V and EQE data


(: https://nanohub.org/)

Online Platform used: NANOHUB online electronic simulation tools

Introduction:
This application is build for the calculating various solar cell parameters
Using the raw I-V and EQE data within the second.
In this tool, we build a simple and cost-effective tools to extract the photovoltaics
parameters form light current-voltage and EQE data. The tools is published as the Web
App using the streamlet library. The tools contains two different parts, (1) Extraction
of the I-V parameters using the raw I-V data, and this will allows us to to know the
photovoltaics parameters of the devices within a second, (2) part is the cutting-edge
EQE-Jsc and Voltage-Loss Analysis Calculator!

Procedure for online simulation:

Step 1. Select “: PV parameters calculator using I-V and EQE” from the list of
Tools in https://nanohub.org/

You might also like