FFBL Test 4

FAUJI FERTILIZER BIN QASIM LIMITED
ENTRANCE TEST
CATEGORY: APPRENTICE TECHNICIAN (MECHANICAL)
TEST PAPER # 4 Time: 40 Minutes
Note: 1- Do not write anything on the “Question Paper”.
2- Tick (  ) the correct answer on “Answer Sheet”.
1- All electric wires should be taken as live wires

a. True b. False
2- Stress on a body is equal to ___________________.
a. Force / Length b. Force x Area
c. Mass x Acceleration d. Force / Area
3- 2” is equal to.
a. 25.4 MM b. 6.35 mm
c. 100 MM d. 50.8 mm
4- A slip is observed in
a. Chain and sprocket drive b. V-belt drive
c. Gear drive d. None of the above
5- Angle greater than 900 is called.

a. Obtuse b. Acute
c. Right d. Reflex
6- A small amount of leakage from glands aids.

a. Lubricating bearing b. Cooling the gland
c. Reducing packing life d. None of the above
7- In which position of gate valve, the erosion is maximum.

a. Full open b. Full close
c. Partial open d. None of the Above
8- Area of a triangle = _______________________.
a. Base x Hypotoneous b. Length x Width

2
c. Base x Attitude d. None of the above
2
9- Argon gas in GTAW welding is used for.
a. Combustion b. Shielding
c. Cooling d. Pressure
10- If base & perpendicular of a right angle triangle is 1, the hypotoneous =
a. 2 b. √2
c. √ 3/2 d. 1
11- In H-beam W 6 x 13, 6 & 13 describe

A. Weight and size B. Size and weight
C. Size and Size D. None of above
12- Electrode is not consumed in _______ type of welding.

A. Gas Tungsten Arc Welding B. Gas Welding
C. Shielded Metal Arc Welding D. Non of the Above
13- RPM is the abbreviation of __________________.

A. Rotor Performance Measurement B. Revolutions Per Minute
C. Raised Performance Measurement D. Reciprocating Piston Movement
14- Seals are used to prevent

A. Leakage B. Flow
C. Surging D. Vibration
15- Up-Down, Side to Side motion is called __________ movement

A. Axial B. Rotary
C. Radial
16- A compressor that operates by volumetric displacement is called ____________

compression.
A. Centrifugal B. Positive Displacement
C. Hydraulic D. Screw
17- When sump pumps are used in a waste pumping system, which of the following is used to
keep large particles from reaching the impeller?
A. Filter B. Intake Screen
C. Large Discharge Pipe D. Strainer
18- In rotary machines, the shaft is supported on ______________.

A. Impeller B. Bearings
C. Seals D. Balancing Pistons
19- Heat transfer in a material by

A. Conduction B. Convection
C. Radiation D. None of the above
20- Circumference of a circle is
A. Лr2 B. 4/3Лr3
C. 2Лr D. None of the above
21- Compression ratio of petrol engine is greater than diesel

a. Yes b. No
c. Equal d. None of the above
22- Type of bearing used in excel hub is

a. Ball type b. Needle type
c. Taper roller type d. All of the above
23- In efficient brake is due to

a. Brake oil leakage b. Pedal play excessive
c. Low tyre pressure d. Slippery road
24- Gear is hard to change because

a. Excessive engine r.p.m b. Clutch plate burnt
c. Excessive speed d. None of the above
25- Which process increase the hardness

a. Casting b. Forging
c. Sand blasting d. None of the above
26- Steam separator are used to prevent / separate ____________ from steam.
a. Water b. Oil
c. Grease d. Suspended solids
27- If we count from 1 – 100, the digit “9” comes how many times
a. 18 b. 19
c. 20 d. 25
28- Ferrite is name given to pure iron

a. True b. False
29- What type of connection provides most easy replacement?

a. Union b. Flanges
c. Welding d. Threaded
30- In double pass exchanger, fluid enters and exists from.
a. Same end b. Different end
31- Basic advantage of steam traps are

a. It conserve energy b. It prevents steam leakages
c. It controls steam flow d. None of above
32- Fluid flows _________________ in the center of the main stream.

a. Fastest b. Slowest
c. Remain Constant d. All of the above
33- Volume flow rate is defined for constant density as

a. AxV b. MxV
c. VxP d. None of them
34- Value of Sin O°

a. 0 b. 1
c. 2 d. None of above
35- For gas pressure increasing __________________ is used.

a. Pump b. Turbine
c. Exchanger d. Compressor
36- Pipes are customarily identified by

a. Nominal pipe size and wall thickness
b. Flange and fitting
c. Length and colour
d. Weight
37- What is the value of “g”

a. 98.1 m/Sec2 b. 9.81 m/Sec2
c. 0.981 m/Sec2 d. 9.6 m/Sec2
38- Rusting is a __________________ change.

a. Chemical b. Physical
c. No of them d. Biochemical change
39- During burning if the smoke is black then the combustion is called ________________.
a. Incomplete b. Complete
c. Uniform d. None of the above

40- Tube side area in heat exchangers are designated as area _________________.
a. Inside the tube b. Out side the tube
c. Both a & b d. None of the above

FAUJI FERTILIZER BIN QASIM LIMITED
ENTRANCE TEST
CATEGORY: APPRENTICE TECHNICIAN (MECHANICAL)
KEY FOR TEST PAPER # 4
Q. # Answer Q. # Answer
1. A 21. B
2. D 22. C
3. D 23. A
4. B 24. B
5. A 25. B
6. B 26. A
7. C 27. C
8. C 28. B
9. B 29. A
10. B 30. A
11. B 31. A
12. A 32. A
13. B 33. A
14. A 34. A
15. C 35. D
16. B 36. A
17. D 37. B
18. B 38. A
19. A 39. A
20. C 40. A

FFBL Test 4

Uploaded by

Copyright:

Available Formats

FFBL Test 4

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FFBL Test 4

Uploaded by

Copyright:

Available Formats

FAUJI FERTILIZER BIN QASIM LIMITED

1- All electric wires should be taken as live wires

2- Stress on a body is equal to ___________________.

a. Force / Length b. Force x Area

c. Mass x Acceleration d. Force / Area

c. Gear drive d. None of the above

5- Angle greater than 900 is called.

6- A small amount of leakage from glands aids.

c. Reducing packing life d. None of the above

7- In which position of gate valve, the erosion is maximum.

8- Area of a triangle = _______________________.

a. Base x Hypotoneous b. Length x Width

10- If base & perpendicular of a right angle triangle is 1, the hypotoneous =

11- In H-beam W 6 x 13, 6 & 13 describe

12- Electrode is not consumed in _______ type of welding.

13- RPM is the abbreviation of __________________.

14- Seals are used to prevent

15- Up-Down, Side to Side motion is called __________ movement

16- A compressor that operates by volumetric displacement is called ____________

18- In rotary machines, the shaft is supported on ______________.

19- Heat transfer in a material by

21- Compression ratio of petrol engine is greater than diesel

c. Equal d. None of the above

22- Type of bearing used in excel hub is

c. Taper roller type d. All of the above

23- In efficient brake is due to

c. Low tyre pressure d. Slippery road

24- Gear is hard to change because

c. Excessive speed d. None of the above

25- Which process increase the hardness

c. Sand blasting d. None of the above

c. Grease d. Suspended solids

28- Ferrite is name given to pure iron

29- What type of connection provides most easy replacement?

31- Basic advantage of steam traps are

c. It controls steam flow d. None of above

32- Fluid flows _________________ in the center of the main stream.

c. Remain Constant d. All of the above

33- Volume flow rate is defined for constant density as

c. VxP d. None of them

34- Value of Sin O°

35- For gas pressure increasing __________________ is used.

36- Pipes are customarily identified by

b. Flange and fitting

c. Length and colour

37- What is the value of “g”

c. 0.981 m/Sec2 d. 9.6 m/Sec2

38- Rusting is a __________________ change.

c. No of them d. Biochemical change

c. Uniform d. None of the above

c. Both a & b d. None of the above

You might also like