xnd-6080_6080v_6080r_6080rv_8080r_8080rv_xnv-6080_6080r_8080r_usermanual

NETWORK CAMERA
User Manual
XND-6080/6080V/6080R/6080RV/8080R/8080RV
XNV-6080/6080R/8080R
Network Camera
User Manual
Copyright
©2017 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the
right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information
theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
overview
Important Safety Instructions WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
1. Read these instructions. TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE
2. Keep these instructions. VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.
3. Heed all warnings. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
●● overview
4. Follow all instructions. such as vases, shall be placed on the apparatus.
5. Do not use this apparatus near water. To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. with the installation instructions.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.) CAUTION
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat. CAUTION
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades RISK OF ELECTRIC SHOCK.
DO NOT OPEN
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and DO NOT REMOVE COVER (OR BACK).
the point where they exit from the apparatus. NO USER SERVICEABLE PARTS INSIDE.
11. Only use attachments/ accessories specified by the manufacturer. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over. EXPLANATION OF GRAPHICAL SYMBOLS
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus intended to alert the user to the presence of “dangerous voltage” within the
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
product’s enclosure that may be of sufficient magnitude to constitute a risk of
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
electric shock to persons.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated
from 12 Vdc, min.0.56 A. (XND-6080/6080V/6080R/6080RV/8080R/8080RV) The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
16. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated the literature accompanying the product.
from 24 Vac (50/60 Hz) min.0.67 A or 12 Vdc, min.0.65 A. (XNV-6080/6080R/8080R)
17. If you use excessive force when installing the product, the camera may be damaged and malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.
18. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As
edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or
near the kitchen table.
This may cause damage to the product.
19. When installing the product, be careful not to allow the surface of the product to be stained with chemical
substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.
20. If you install/disassemble the product in a manner that has not been recommended, the production functions/
performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
21. Installing or using the product in water can cause serious damage to the product.
English _3
overview
Class construction Please read the following recommended safety precautions carefully.
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a yy Do not place this apparatus on an uneven surface.
protective earthing connection. yy Do not install on a surface where it is exposed to direct sunlight, near heating equipment or
heavy cold area.
Battery yy Do not place this apparatus near conductive material.
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as yy Do not attempt to service this apparatus yourself.
sunshine, fire or the like.
yy Do not place a glass of water on the product.
Disconnection Device yy Do not install near any magnetic sources.
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in yy Do not block any ventilation openings.
your location. yy Do not place heavy items on the product.
When used outside of the U.S., it may be used HAR code with fittings of an approved yy Please wear protective gloves when installing/removing the camera.
agency is employed. The high temperature of the product surface may cause a burn.
CAUTION User’s Manual is a guidance book for how to use the products.
Risk of explosion if battery is replaced by an incorrect type. The meaning of the symbols are shown below.
Dispose of used batteries according to the instructions.
yy Reference : In case of providing information for helping of product’s usages
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in yy Notice : If there’s any possibility to occur any damages for the goods and human caused by
the operating instructions unless you are qualified to do so. not following the instruction
The CVBS out terminal of the product is provided for easier installation, and is not  Please read this manual for the safety before using of goods and keep it in the safe place.
recommended for monitoring purposes.
Please use the input power with just one camera and other devices must not be connected.
The ITE is to be connected only to PoE networks without routing to the outside plant.
4_ overview
CONTENTS web viewer 30 Connecting to the Camera
31 Password setting
overview 3
6
Important Safety Instructions
Product Features 30 31
31
Login
Plug-in support specifications for each
3
browser
6 Recommended PC Specifications 32 Installing WebViewer Plugin
6 Recommended Micro SD/SDHC/SDXC 32
●● overview
Using a Plug-in Free Webviewer
Memory Card Specifications 32 Using the Live Screen
6 NAS recommended specs 35 Playing the recorded video
7 What’s Included
8 At a Glance (XND-6080/6080R/8080R)
10 At a Glance (XND-6080V/6080RV/8080RV)
12 At a Glance (XNV-6080/6080R/8080R) setup screen 37 Setup
37 Basic Setup
installation & connection 14

15
Installation (XND-6080/6080R/8080R)
Installation (XND-6080V/6080RV/8080RV)
37 41
42
48
51
PTZ setup
Video & Audio setup
Network Setup
14
Event Setup
16 Installation (XNV-6080/6080R/8080R) 53 NAS (Network Attached Storage) guide
19 Inserting/Removing a Micro SD Memory 56 Configure analysis settings
Card 60 System Setup
20 Connecting with other Device 62 Open Platform Setup
20 Memory Card Information (Not Included)
appendix 63 Specification
network connection and 24 Connecting the Camera Directly to Local 65 Product Overview
setup
63
Area Networking 67 Troubleshooting
24 Connecting the Camera Directly to a DHCP 68 Open Source Announcement
24
Based DSL/Cable Modem
25 Connecting the Camera Directly to a
PPPoE Modem
25 Connecting the Camera to a Broadband
Router with the PPPoE/Cable Modem
26 Buttons used in IP Installer
26 Static IP Setup
28 Dynamic IP Setup
28 Port Range Forward (Port Mapping) Setup
29 Connecting to the Camera from a Shared
Local PC
29 Connecting to the Camera from a Remote
PC via the Internet
English _5
overview
Product Features Recommended PC Specifications
•• Dustproof/Waterproof (IP67, IP66) (XNV-6080/6080R/8080R) •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher
The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing •• RAM : 8G or higher
it to rain. •• Supported OS : Windows 7, 8.1, 10, Mac OS X 10.10, 10.11, 10.12
•• IR mode (XND-6080R/6080RV/8080R/8080RV, XNV-6080R/8080R) •• Plug-in free web viewer
If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright, Supported web browsers : Google Chrome, MS Edge, Mozilla Firefox(Windows 64bit only), Apple Safari 9 (Mac
which helps you identify the object in near distance. OS X only)
•• Supports 2M pixel resolution videos (XND-6080/6080V/6080R/6080RV, XNV-6080/6080R) •• Plug-in Webviewer
•• Supports 5M pixel resolution videos (XNV-8080R, XND-8080R/8080RV) Supported web browsers : MS Explorer 11, Apple Safari 9 (Mac OS X only)
•• Multi-Streaming
This network camera can display videos in different resolutions and qualities simultaneously using different
CODECs. Recommended Micro SD/SDHC/SDXC Memory Card
•• Web Browser-based Monitoring Specifications
Using the Internet web browser to display the image in a local network environment.
•• Alarm •• Recommended capacity : 16GB to 256GB (MLC type)
When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server, •• The following types of memory cards from the following manufacturers are recommended for this camera.
saved in a Micro SD card or NAS, or a signal is sent to the alert output terminal. -- Manufacturer : SanDisk, Transcend
•• Tampering Detection -- Product family : High endurance
Detects tempering attempts on video monitoring.
•• Defocus detection function
Detects the defocus phenomenon of the camera lens. NAS recommended specs
•• Motion Detection
•• Recommended capacity : 200GB or higher is recommended.
Detects motion from the camera’s video input.
•• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.
•• Audio Detection
Detects sound louder than a certain level specified by user. •• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
•• Smart Codec Recommended products Available sizes
Adaptively applies codecs for a portion of the camera’s field of view to improve the quality of such area specified QNAP NAS A maximum of 16 cameras can access simultaneously.
by user. Synology NAS A maximum of 16 cameras can access simultaneously.
•• Auto Detection of Disconnected Network
Detects network disconnection before triggering an event.
•• Fog detection JJ `` If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.
Detects fog that is heavier than the detection level.
•• Face Detection
Detects faces in the specified area from the camera’s video input.
•• IVA (Intelligent Video Analysis) function
Detects a motion or situation that meets the configured event rules.
•• Sound source classification
Detects a sound source specified by the user.
•• ONVIF Compliance
This product supports ONVIF Profile S&G.
For more information, refer to www.onvif.org.
6_ overview
What’s Included Appearance Item Name Quantity Description Model Name
Please check if your camera and accessories are all included in the product package. XND-6080/6080V/
(As for each sales country, accessories are not the same.) 2 6080R/6080RV/
8080R/8080RV
Appearance Item Name Quantity Description Model Name Used for installation on the wall or
Tapping Screw
●● overview
ceiling
XNV-6080/
XND-6080/ 3
1 6080R/8080R
6080R/8080R
XND-6080V/
Used to remove and replace the dome 6080RV/8080RV/
XND-6080V/ L Wrench 1
Camera 1 cover XNV-6080/
6080RV/8080RV
6080R/8080R
XNV-6080/
XNV-6080/ Power Cable 1 Used to plug into the power port
1 6080R/8080R
6080R/8080R
CAUTION:
Rated Voltageconnection.
of the power
Be ware
and Polarity
+
-
of the
AC
24V
/ DC
12V
T
F
N
RESET
W
VIDEO
AF
Used to connect with the audio and XNV-6080/

Instruction book, Audio/alarm cable 1
1 Use for all models alarm port 6080R/8080R
Installer S/W CD
Used to connect the LAN cable with a XNV-6080/

Quick Guide Cable bush 1
1 Use for all models diameter of Ø7~8.5. 6080R/8080R
(Optional)
For fixing a screw, Inserted in a hole XNV-6080/

Plastic Anchor 3
Warranty card (reinforced anchoring force) 6080R/8080R
1 Use for all models
(Optional)
Used for assembling the dome case
when installing the product on the XNV-6080/
Used to test the camera connection to Machine Screws 3
Cable for the testing monitor 1 Use for all models pipe, wall mount, etc. or blocking a 6080R/8080R
a portable display device hole.
XNV-6080/
Card-type moisture absorbent 1 Attached when installed.
Template 1 Product installation guide Use for all models 6080R/8080R
Options (not included)

Power Terminal Block 1 Plugged in the power plug Use for all models
Housing for installing indoor buried
Indoor Buried Housing Use for all models
type cameras
XND-6080/6080V/
Alarm cable 1 Used when connecting to an alarm 6080R/6080RV/
8080R/8080RV
English _7
overview
At a Glance (XND-6080/6080R/8080R) Components
Appearance
b ab c
T
d T
d
SE SE
e e
T RE T RE
F F
AF AF
N N
W W
DC 12
V ALARM:1
OUT 1 2 3
US
B
VID
EO f DC 12
V ALARM:1
OUT 1 2 3
US
B
VID
EO f
ALARM:2 ALARM:2
g g
IN IN
GND :3 GND :3
b
h h
c i i
<XND-6080> <XND-6080R/8080R>
Item Description
a Dome cover Case cover used to protect the lens and the main unit. o
b Camera Case Housing part that covers the camera body.
c Microphone hole Microphone is embedded.
T AUDIO IN T OU
LINK AC
j kl m n
8_ overview
Item Description Item Description
a Illumination Sensor Detects incoming light to control the IR LED. l Audio Out Jack Used to connect to speakers.
b Lens Lens for the camera. m Network Port Used to connect the PoE or Ethernet cable for network connection.
●● overview
c IR LED These infrared LED’s are controlled by the illumination sensor. n Microphone hole Microphone is embedded.
The button restores all camera settings to the factory default. Inside cover Protective cover for the main body.
Press and hold for about 5 seconds to reboot the system.
o
Reset Button J ‌If you reset the camera, the network settings will be adjusted so that DHCP can be
d enabled. If there is no DHCP server in the network, you must run the IP Installer
program to change the basic network settings such as IP address, Subnet mask,
Gateway, etc., before you can connect to the network.
T Zoom in (Tele)
W Zoom out (Wide)
e Zoom/Focus Control Button N Focusing on a near object (Near)
F Focusing on a far object (Far)
Focus Control Press this button for automatic focus control.
Output port for test monitoring the video output. Use the test monitor cable to connect to a
f Test Monitor Out
mobile display and check the test video.
Port to connect the Wi-Fi dongle.

You can check the installation video through the applications installed in the smartphone.
g MICRO USB port
Refer to “Connect to WiFi dongle” on page 21.
`` Wifi dongle and OTG gender are sold separately.
ARM-IN Used to connect the alarm input sensor or external day/night sensor.
h Alarm I/O Port ARM-OUT Used to connect the alarm output signal.
GND These are common ports to connect alarm input/output signals.
i Power Port Port for power terminal block.
Micro SD Memory Card

j Compartment for the Micro SD memory card.
Compartment
k Audio In Jack Used to connect to a microphone.
English _9
overview
At a Glance (XND-6080V/6080RV/8080RV) Components
Appearance
b ab c
T
d T
d
SE SE
e e
T RE T RE
F F
AF AF
N N
W W
DC 12
V ALARM:1
OUT 1 2 3
US
B
VID
EO f DC 12
V ALARM:1
OUT 1 2 3
US
B
VID
EO f
ALARM:2 ALARM:2
g g
IN IN
GND :3 GND :3
c b
h h
i i
<XND-6080V> <XND-6080RV/8080RV>
Item Description
a Dome cover Case cover used to protect the lens and the main unit.

o
c Microphone hole Microphone is embedded.
T AUDIO IN T OU
LINK AC
j kl m n
10_ overview
a Illumination Sensor Detects incoming light to control the IR LED. l Audio Out Jack Used to connect to speakers.
b Lens Lens for the camera. m Network Port Used to connect the PoE or Ethernet cable for network connection.
●● overview
c IR LED These infrared LED’s are controlled by the illumination sensor. n Microphone hole Microphone is embedded.
The button restores all camera settings to the factory default. Inside cover Protective cover for the main body.
o
T Zoom in (Tele)
W Zoom out (Wide)
f Test Monitor Out

g MICRO USB port
ARM-IN Used to connect the alarm input sensor or external day/night sensor.
h Alarm I/O Port ARM-OUT Used to connect the alarm output signal.
GND These are common ports to connect alarm input/output signals.
i Power Port Port for power terminal block.

j Compartment for the Micro SD memory card.
Compartment
k Audio In Jack Used to connect to a microphone.
English _11
overview
At a Glance (XNV-6080/6080R/8080R) Components
Appearance b de ab c d e
RESET
RESET
AF
AF
F
F
W
W
T
T
NETWORK NETWORK
N
ALARM ALARM
AUDIO AUDIO
VIDEO
VIDEO
USB
USB
LINK ACT LINK ACT
12 4V
12 4V
DC C 2
DC C 2
V
V
A
A
+
-
AC
24
V/
DC
12
V
T
b
F
N
RESE
W
VID EO
AF
T
f g h f g h
<XNV-6080> <XNV-6080R/8080R>
Item Description
a Dome cover Case cover used to protect the lens and the main unit.
A
AL UDIO
AR
M AC
1 T
NE LIN
TW K
OR
2 K
i jk
12_ overview
Item Description
a Illumination Sensor Detects incoming light to control the IR LED.
b Lens Lens for the camera.
●● overview
c IR LED These infrared LED’s are controlled by the illumination sensor.
The button restores all camera settings to the factory default.

T Zoom in (Tele)
W Zoom out (Wide)
f Power Port Port for power terminal block.

g MICRO USB port
h Test Monitor Out

i Compartment for the Micro SD memory card.
Compartment
Plug in the audio and alarm cable to this port to connect with external alarm device/
j Audio and alarm cable port
microphone/speaker.
k Network Port Used to connect the PoE or Ethernet cable for network connection.
English _13
installation & connection
Installation (XND-6080/6080R/8080R) 2. Using 2 tapping screws provided, fix the camera at 2 holes drilled
with a template.
GND :3
IN
ALAR :2
OUT M 1 2
ALARM:1 3
DC 12V
`` Set the < > mark imprinted on the camera to face the direction of camera
VID
EO
US
Precautions before installation

B
W
N
AF
F
RE T
SE
monitoring.
T
Ensure you read out the following instructions before installing the camera:
3. Connect the camera internal terminal with the corresponding
•• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera cable.
including the installation bracket.
4. Adjust the lens in a desired direction by referring to the “Adjusting
•• Stuck-in or peeled-off cables can cause damage to the product or a fire. the monitoring direction for the camera” section. (page 18)
•• For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
JJ `` We recommend you not to touch the lens as the camera lens has been
properly focused in the final process of manufacturing. If so, the lens may be out of focus or stained by alien substances.
Disassembling
5. Please connect the inner cover to the main body.
1. Use one hand to hold the camera’s bottom part and turn the cover Dome cover
6. While grabbing the bottom side of the camera with your hand, please
counterclockwise with another hand to separate it.
grab and push its cover with the other hand to align the two arrow signs,
as shown in the figure.
JJ `` When connecting the dome cover, align the arrows and connect it perpendicularly
to the main body.
If the dome cover is not connected properly, it can result in a distortion of the hood
around the lens, causing scattered reflection.
Secure the dome cover firmly. If the dome cover has not been turned or is not
NETWORK
ALARM
AUDIO
LINK ACT
assembled properly, it could cause scattered reflection, or the parts around the lens
12 V
DC C 24
V
T
could move and cause a change in the shooting range.
A
SE
T RE
F
AF
N
W
B
US O
DC 12V VIDE
`` Make sure that the dome cover is correctly connected to the bottom part as shown
ALARM:1 3
OUT M 1 2
ALAR :2
IN
GND :3
in the figure.
If the snap-fit is not connected correctly, the dome cover may fall, which may cause
2. Lift up the inner cover to separate it. injury.
T
SE
T RE
F
AF
N
W
B
US O
DC 12 VIDE
V ALARM:1 3
OUT M 1 2
ALAR :2
IN
GND :3
Installation
1. Attach the installation template to the selected area and punch 3
holes as shown in the figure.
14_ installation & connection

Installation (XND-6080V/6080RV/8080RV) 2. Using 2 tapping screws provided, fix the camera at 2 holes drilled
with a template.
GND :3
IN
ALAR :2
OUT M 1 2
ALARM:1 3
DC 12V
`` Set the < > mark imprinted on the camera to face the direction of camera
VID
EO
US
Precautions before installation

B
W
N
AF
F
RE T
SE
monitoring.
T
3. Connect the camera internal terminal with the corresponding
•• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera cable.
●● installation & connection

•• Stuck-in or peeled-off cables can cause damage to the product or a fire. the monitoring direction for the camera” section. (page 18)
•• For safety purposes, keep anyone else away from the installation site.
JJ `` We recommend you not to touch the lens as the camera lens has been properly focused in the final process of
manufacturing. If so, the lens may be out of focus or stained by alien substances.
Disassembling
5. Please connect the inner cover to the main body.
1. Use the hex key in the package to separate the dome Dome cover
6. Grab the bottom part of the camera with one hand and the cover with
cover by unscrewing the three (3) locking bolts of the dome
the other hand, align the arrows and assemble them using the hex key.
cover, turning them counterclockwise.
JJ `` When connecting the dome cover, align the arrows and connect it perpendicularly
to the main body.
If the dome cover is not connected properly, it can result in a distortion of the hood
Bolts around the lens, causing scattered reflection.
Make sure that the dome cover is connected firmly to the other part. If the dome
cover is not correctly connected to the bottom of the main body, scattered reflection
NETWORK
ALARM
AUDIO
LINK ACT
might occur.
12 V
DC C 24
V
A
T
SE
T RE
F
AF
`` Make sure that the dome cover is correctly connected to the bottom part as shown
N
W
B
US O
DC 12V VIDE
ALARM:1 3
OUT M 1 2
in the figure.
ALAR :2
IN
GND :3
If the snap-fit is not connected correctly, the dome cover may fall, which may cause
injury.
2. Lift up the inner cover to separate it.
`` When assembling the dome cover to the camera, make sure not to let the safety
wire get stuck between the dome cover and the camera. This will cause IR
scattered reflection.
T
LINK AC
T RE
SE T OUT AUDIO IN
F
AF
N
W
B
US O
DC 12 VIDE
V ALARM:1 3
OUT M 1 2
ALAR :2
IN
GND :3
Installation
1. Attach the installation template to the selected area and punch 3
holes as shown in the figure.
English _15
Installation (XNV-6080/6080R/8080R) Installation
1. Drill a hole (diameter : 6mm, depth : min 55mm) of the case
`` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are bottom and insert the provided plastic anchor to the end.
JJ recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. 2. Fit the bottom hole to the anchor hole and insert and fix the taping
screw (M4.5xL50).
DC C 24
A
12 V
V
Precautions before installation 3. Connect and arrange the necessary cables lest that they should
VIDEO
VIDEO
ACT
ACT LINK
LINK
AUDIO
AUDIO
ALARM
ALARM
NETWORK
NETWOR K
N
N
be damaged or twisted while installing the camera.
W
W
T
T
FF
AF
AF
RESET
RESET
•• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera the monitoring direction for the camera” section. (page 18)
5. Close the dome cover.
•• Stuck-in or peeled-off cables can cause damage to the product or a fire.
`` Securely fasten the fastening bolt using an L wrench to prevent water from
•• For safety purposes, keep anyone else away from the installation site. leaking.
Connecting waterproof power cable and LAN cable

Disassembling
1. Remove the dome cover and the case.
1. Using the L wrench provided, turn the 3 fastening bolts Dome cover 2. Pull out the long projected part of the rubber plug on the bottom and
on the dome cover counter clockwise to remove the
remove it as shown in the figure.
cover.
JJ `` Use an appropriate cable bush for the LAN cable to be connected.

-- Basic camera : Use the cable with a diameter of Ø5~6.5.
-- Components provided : Use the cable with a diameter of Ø7~8.5. AU
AL DIO
AR
M AC
1 T
NET LINK
WO
RK
2
Bolts
RESET
RESET
AF
AF
FF
W
W
T
T
NETWORK
NETWO RK
N
N
ALARM
ALARM
AUDIO
AUDIO
VIDEO
VIDEO
LINK
LINK ACT
ACT
Camera Body
12 4V
DC C 2
V
A
3. Insert the power cable into the small hole made by removing the projected
part of the rubber plug in step 2 above, and lay the cable along the long
groove.
4. Connect the power cable with the power terminal block.
Camera Case
RESET
AF
F
W
T
NETWORK
N
ALARM
AUDIO
VIDEO
USB
LINK ACT
12 4V
DC C 2
V
A
5. Insert the LAN cable into the large hole made by removing the projected Attaching to the unbundled adapter
part of the rubber plug in step 2 above.
Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation
6. Remove the sheath with a cable cutter, and align the cables. site or for your convenience.
7. Connect the LAN cable with a LAN connector, and insert it into the LAN
1. Remove the dome cover from the case by referring to the “Disassembling” section. (page 16)
tool.
2. Use the provided machine screw to fix the camera case to the unbundled adapter.
8. Connect the finished cable to the Ethernet port.
AU

AL DIO
AR
M AC
1 T
NET LINK
3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the
WO
RK
2
camera.
4. Install the camera body in the reverse order of “Disassembling”.
5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the
camera” section. (page 18)
CA ted e po
Ra th
UT Vo we
of
IO lta r
N: ge co
Be an nn
wa d ec tio
re Po n.
of lar
th ity
e
6. Close the dome cover.
`` Securely fasten the fastening bolt using an L wrench to prevent water from leaking.
Connecting the alarm and audio cable Outdoor installation

1. Remove the dome cover and the case. When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be
2. Pull out the rubber plug on the bottom as shown in the figure. purchased in stores) so that water does not leak from the gap of the cable connected to the outside.
1. Connect the power, I/O, BNC, and LAN cables. Camera System
2. Wrap the black cable jacket (Area A) and the cable connection area
with waterproof (butyl rubber) tape so that more than half of the
butyl rubber tape is overlapped. Camera System
AU
AL DIO
AR
M
JJ `` Ifleakage.
AC
the cable jacket is not waterproofed properly, then it can directly cause
1 T
NET LINK
WO
2
RK
A A
Make sure to protect the cable with a dense layer of taping. Camera System
`` Waterproof butyl tape is made of butyl rubber that can be stretched to twice
its normal length.
3. Insert the alarm/audio cable through the hole created by removing the
rubber cap in No. 2, and connect the cable to the alarm terminal.
4. Align the cable so that it should not be damaged or jammed when
installing the camera.
5. Put the rubber cap located on the alarm/audio cable in the hole.
6. Adjust the lens in a desired direction by referring to the “Adjusting the
AU
AL DIO
AR
M AC
1 T
monitoring direction for the camera” section. (page 18)

NE LINK
TW
OR
2 K
7. Attach the dome cover.
English _17
Optional Accessories for Installation Adjusting the monitoring direction for the camera
For your easier installation, you can purchase appropriate optional accessories available. Pan
1. WALL MOUNT ADAPTOR(SBP-300WM or SBP-300WM1)/
HANGING MOUNT(XND-6080/6080V/6080R/6080RV/8080R/
8080RV : SBP-300HM8, XNV-6080/6080R/8080R : SBP-
300HM6)
This adaptor is used when installing the dome camera onto a
DC C 24
A
12 V
V
wall.
USB
VIDEO
ACT LINK
AUDIO
ALARM
NETWORK
N
W
T
F
AF
RESET
Tilt
Lens rotation
2. CEILING MOUNT ADAPTOR(SBP-300CM)/HANGING MOUNT(XND- `` Adjusting the monitoring direction

6080/6080V/6080R/6080RV/8080R/8080RV : SBP-300HM8, XNV- You can adjust the camera direction only when the camera is fixed on the ceiling.
6080/6080R/8080R : SBP-300HM6) Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the
This adaptor is used when installing the dome camera on a concrete lens on its axis is called Rotation.
ceiling.
-- The effective range of pan is a total of 354 degrees.
-- The effective range of rotation is a total of 355 degrees.
-- The effective range of tilt is a total of 67 degrees.
JJ `` The image can be covered up by the camera case depending on the angle.
`` Do not forcefully turn the focus/zoom lens after the dome case is disassembled.
Otherwise, it may cause an incorrect focus due to a motor failure.
3. POLE MOUNT ADAPTOR(SBP-300PM)
This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP- `` Methods of adjustment
300WM1) installation on a pole whose diameter is bigger than 80mm. 1. After installing the camera, adjust the panning angle in consideration of the monitoring direction.
2. Set the horizontal angle so that the image is not reversed.
3. Adjust the tilt angle so that the camera faces toward the monitoring object.
4. CORNER MOUNT ADAPTOR (SBP-300KM)

This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or
SBP-300WM1) installation on the corner of wall joint.

Inserting/Removing a Micro SD Memory Card Removing a Micro SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory
`` Disconnect the power cable from the camera before inserting the Micro SD memory card. card from the slot.
JJ
`` Do not insert the Micro SD memory card while it’s upside down by force.
Otherwise, it may damage the Micro SD memory card.

`` When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
`` Disassembly of the product cover should be finished within 5 minutes, or there will be the risk of internal dew condensation.
Inserting a Micro SD Memory Card

1. Separate the Dome cover of the camera.
2. Insert a Micro SD card in the arrow direction shown in the figure. IN
UT AUDIO CT O
LINK A T AUDIO IN T OU
LINK AC
<XND-6080/6080V/6080R/6080RV/8080R/8080RV>
A
AL UDIO
IN
UT AUDIO CT O AR
M AC
LINK A T AUDIO IN 1 T
LINK AC
T OU
NE LIN
TW K
OR
2 K
A
AL UDIO
AR
M AC
1 T
NE LIN
TW K
OR
<XND-6080/6080V/6080R/6080RV/8080R/8080RV>
2 K
A
<XNV-6080/6080R/8080R>
AL UDIO
AR
M AC
JJ `` Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released.
1 T
NE LIN
TW K
OR
2 K
`` Before removing your Micro SD memory card, turn off the camera or go to <Storage>, turn the device off, and press the
A
AL UDIO
AR
M AC
1 T
NE LIN
TW K
[Apply] button. (Page 52)

OR
2 K
`` If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or
damaged.
<XNV-6080/6080R/8080R>
English _19
Memory Card Information (Not Included) Connecting with other Device
What is a memory card?

SOFT AP
The memory card is an external data storage device that has been developed to offer an entirely new way to
record and share video, audio, and text data using digital devices. Wi-Fi dongle
Selecting a memory card that’s suitable for you Monitor to install

Your camera supports Micro SD/SDHC/SDXC memory cards.
You may, however, experience compatibility issues depending on the model and make of the memory card.
The following types of memory cards from the following manufacturers are recommended for this camera.
-- Manufacturer : SanDisk, Transcend Ethernet
-- Product family : High endurance T
F
RE
SE
AF
T
Power
N
It is recommended to use a 16GB to 256GB (MLC type) memory card for this camera.
W
B
US O
DC 12 VIDE
V ALARM:1
OUT 1 2 3
ALARM:2
Playback performance can be affected depending on the speed of memory card.

IN
GND :3
Memory Card Components

<XND-6080/6080V/6080R/6080RV/8080R/8080RV>
Contacts SOFT AP
Wi-Fi dongle
Micro SD/SDHC/SDXC
AU
AL DIO
AR
M AC
1 T
NE LIN
TW K
OR
2 K
RESET
AF
F
W
T
NETWORK
N
ALARM
AUDIO
VIDEO
ACT
USB
LINK
Monitor to install
12 4V
DC C 2
V
A
Ethernet
Power
CA te e po
Ra th
UT d Vo we
of
IO lta r
N: ge co
Be an nn
wa d ec tio
re Po n.
of lar
th ity
e
<XNV-6080/6080R/8080R>
JJ `` The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.
`` The Micro USB out terminal of the product is provided for easier installation, and is not recommended for monitoring
purposes.

Ethernet Connection Power Supply (XNV-6080/6080R/8080R)
Connect the Ethernet cable to the local network or to the Internet. Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the
camera.
Connecting Wi-Fi
Camera Setup
JJ `` When supplying PoE and DC 12V or PoE and AC 24V power at the same time, the equipment is powered by the external
source (AC 24V, DC 12V).

1. Connect OTG gender (5-pin) and WiFi dongle to the micro USB terminal. -- You can also use a router featuring PoE to supply power to the camera.
Smartphone Setup -- Use PoE that is compliant with the IEEE 802.3af protocols.
1. Install the Wisenet Installation application. -- It is recommended to use a single source for powering the equipment among PoE, DC 12V and AC 24V.
2. Select the camera SSID after turning on the WiFi. `` Be careful not to reverse the polarity when you connect the power cable.
3. Run the Wisenet Installation application. `` AC 24V can be connected in non-polar union.
4. When you log in to the camera, the video will be connected. (initial password: 4321) `` If you want to connect an external device, you must turn off the external device before proceeding.
`` The video will be played without being logged in during the initial connection. `` Connect the set and the adapter power line first, and then connect the power cable to the outlet on the wall.
5. The camera angle can be adjusted through the smartphone video.

Power Cable Specification for Each Model
Recommended dongle manufacturer
Model Input power Wire Type (AWG) Cable Length (Max.)
Manufacturer Model #22 15m
XND-6080/6080V DC 12V
#20 24m
NETIS WF2123 n300
XND-6080R/8080R/ #20 17m
EDIMAX EW-7811Un DC 12V
6080RV/8080RV #18 27m
IP Time N100mini #22 15m
DC 12V
TP-LINK TL-WN823N V1 #20 24m
XNV-6080
ASUS USB-N13 #22 25m
AC 24V
NETGEAR WNA3100M #20 40m
#18 19m
DC 12V
#16 30m
Power Supply (XND-6080/6080V/6080R/6080RV/8080R/8080RV) XNV-6080R/8080R
#20 26m
AC 24V
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the #18 40m
camera.
Network Cable Specification
JJ `` If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from DC 12V. Item Contents Remark
-- You can also use a router featuring PoE to supply power to the camera.
Connector RJ45 (10/100/1000BASE-T)
-- Use PoE that is compliant with the IEEE 802.3af protocols. To operate with 1000BASE-T, a cable of
-- It is advisable to use only one power source from PoE and DC 12V. Ethernet 10/100/1000BASE-T UTP-6 or higher should be used for the
`` Be careful not to reverse the polarity when you connect the power cable. Giga hub.
Cable UTP Category 6
`` If you want to connect an external device, you must turn off the external device before proceeding.
Max Distance 100M
`` Connect the set and the adapter power line first, and then connect the power cable to the outlet on the wall.
PoE Support IEEE 802.3af
English _21
Connecting to Audio Input/Output •• Audio in (XND-6080/6080V/6080R/6080RV/8080R/8080RV) : Selectable (microphone/Line-in/Built-in
microphone), Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm
Speaker •• Audio in (XNV-6080/6080R/8080R) : Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA),
Input impedance: 2K Ohm
•• Audio out : Line-out (3.5mm mono jack), Maximum output: 1Vms
Microphone PC •• Line out impedance : 600Ω
Connecting to the I/O port box

Network Connect the Alarm I/O cable to the corresponding port of the port box.
Microphone
Amp Amp Speaker PC

Speaker
Microphone
Microphone
T
SE
T RE
F
AF
Speaker
N
W
B
US O
DC 12 VIDE
V ALARM:1
OUT 1 2 3
Network
ALARM:2
IN
GND :3
Speaker Amp Amp Microphone

Sensor Alarm
(Warning lamp)
Microphone <XND-6080/6080V/6080R/6080RV/8080R/8080RV>
Speaker
1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the
microphone is connected to.
MM `` You can use the built-in microphone in the camera without connecting an external microphone.
(only available in XND-6080/6080V/6080R/6080RV/8080R/8080RV)
2. Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the amplifier that the
speaker is connected to. A
ALAUDIO
3. Check the specifications for audio input.

RM
AC
1 T
NE LIN
TW K
OR
K
•• Audio Codec
2
-- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate:
16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling
Frequency: 16kHz)
-- Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)
•• Full duplex Audio
Sensor
Alarm (Warning lamp)
<XNV-6080/6080R/8080R>
•• ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.
•• ALARM-OUT : Used to connect the alarm output signal.
•• GND : Common port for alarm in/output signal.
JJ `` Ifcollector
devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open
method, it may cause malfunction.

Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. (page 23)
To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the
other strand to the [GND] port.
Alarm In Wiring Diagram

External Inside of the camera VCC_3.3V
connection
RESISTOR RESISTOR
Sensor
ALARM IN (5mA SINK) RESISTOR DIODE
MLCC TRANSISTOR
GND
GND
To connect the alarm out

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by
using the open collector method, it may cause malfunction.
Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and
current specifications.
Alarm Out Wiring Diagram

External connection Inside of the camera
Warning lamp / DC 5V or 3.3V
Siren power
(-) (+)
DIODE
RESISTOR 10K ohm
ALARM OUT (12VDC 20mA MAX)
TRANSISTOR RESISTOR
Warning lamp / RELAY TRANSISTOR

Siren
GND
GND
GND
English _23
network connection and setup
You can set up the network settings according to your network configurations. Connecting the Camera Directly to a DHCP Based DSL/Cable
Modem
Connecting the Camera Directly to Local Area Networking
Connecting to the camera from a local PC in the LAN
VIDEO
RESET
AF
W
N
F
12V
T
/ DC
24V
INTERNET
AC
-
+
DSL/Cable Modem
1. Launch an Internet browser on the local PC. External Remote PC
2. Enter the IP address of the camera in the address bar of the browser. Camera
DDNS Server
(Data Center, KOREA)
Camera
1. Connect the user PC directly with the network camera.
VIDEO
RESET
AF
2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on
W
N
F
12V
T
/ DC
24V
AC
INTERNET
-
+
your desktop to connect to the Internet.

3. Use the Internet browser to connect to the web viewer.
External Remote PC
Camera
4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.
DDNS Server
6. Move to [Basic] – [IP & Port], and set the IP type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
Local PC (Data Center, KOREA)
<Local Network> 8. Restart the camera.
MM `` Aif the
remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet
port-forwarding is not properly set or a firewall is set.
MM `` For configuring the DDNS settings, refer to “DDNS”. (page 48)
`` For registering the DDNS settings, refer to “Registering with DDNS”. (page 48)
In this case, to resolve the problem, contact your network administrator.
`` Refer to “IP & Port” for how to setup IP. (page 40)
`` In the IP installer, you can use the initial password, “4321” to set IP Address, Subnet Mask, Gateway, HTTP Port, VNP Port, IP
type. After changing the network interface, for better security, access the web viewer and change the password.
`` By factory default, the IP address will be assigned from the DHCP server automatically.
If there is no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 26)
24_ network connection and setup

Connecting the Camera Directly to a PPPoE Modem Connecting the Camera to a Broadband Router with the
PPPoE/Cable Modem
VIDEO
RESET
AF
W
N
F
12V
T
This is for a small network environment such as homes, SOHO and ordinary shops.
/ DC
24V
INTERNET
AC
-
+
PPPoE Modem
External Remote PC
●● network connection and setup

Camera
Camera
DDNS Server
(Data Center, KOREA)
VIDEO
RESET
AF
W
N
F
12V
T
/ DC
24V
AC
-
+
INTERNET
PPPoE or PPPoE or
Broadband
1. Connect the user PC directly with the network camera.
Cable Modem Cable Modem
Camera Router External Remote PC
2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on
your desktop to connect to the Internet.
DDNS Server
3. Use the Internet browser to connect to the web viewer. (Data Center, KOREA)
Local PC
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
Configuring the network settings of the local PC connected to a Broadband Router
6. Move to [Basic] – [IP & Port] Setup Page, set the IP type to [PPPoE], and enter the network service’s ID
Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions
and password.
below.
7. Connect the camera, which was removed from your PC, directly to the modem.
•• Select : <Network>  <Properties>  <Local Area Connection>  <General>  <Properties> 
8. Restart the camera. <Internet Protocol (TCP/IP)>  <Properties>  <Obtain an IP address automatically> or <Use the
following IP address>.
MM `` For configuring the DDNS settings, refer to “DDNS”. (page 48) •• Follow the instructions below if you select <Use the following IP address>:
`` For registering the DDNS settings, refer to “Registering with DDNS”. (page 48) ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1
IP address : 192.168.1.100
`` Refer to “IP & Port” for how to setup IP. (page 40)
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1
IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1
IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
MM ```` For the address of the Broadband Router, refer to the product’s documentation.
For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”.
(Page 28)
English _25
Buttons used in IP Installer Item Description
Scans for cameras with the IPv6 setting.
i IPv6
a b c d e f g Activated in an IPv6 compliant environment only.
Scans for cameras that are currently connected to the network.
j Search
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
k Auto Set The IP Installer automatically configures the network settings.
l Manual Set You should configure the network settings manually.
m Exit Exits the IP Installer program.
MM `` For the IP installer, use only the installer version provided in the installation CD or use the latest one if available. You can download
the latest version from the Hanwha Techwin web site.
`` If the supporting OS is Windows 8.1, it is recommended that you use the Wisenet Device Manager instead of the IP Wisenet.
The Wisenet Device Manager Program can be downloaded by visiting the Hanwha Techwin website (http://www.hanwha-
security.com) under the menu <Customer Support> - <Technical Guides> - <Online Tool>.
hi j k l m
Static IP Setup
Item Description
Model name of the connected camera. Manual Network Setup
a Device Name Click the column to sort the list by model name. Run <IP Installer_v2.XX.exe> to display the camera search list.
However, search will be stopped if clicked during the search. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
Alias
b This function is not currently implemented.
MM `` For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.
Displays either <Static>, <Dynamic> or <PPPoE> for the current network connection
c Mode 1. Select a camera in the search list.
status.
Check the MAC address of the camera on the camera’s label.
Ethernet address for the connected camera. Both the [Auto Set] and [Manual Set] buttons will be
d MAC(Ethernet) Address Click the column to sort the list by Ethernet address. activated.
However, search will be stopped if clicked during the search. 2. Click [Manual Set].
IP address. The Manual Setting dialog appears.
IP Address Click the column to sort the list by IP address. <IP Address>, <Subnet Mask>, <Gateway>, <HTTP
e Port>, and <VNP Port> of the camera are displayed in the
However, search will be stopped if clicked during the search.
preset values.
Network setting for the camera.
3. In the <Address> pane, provide the necessary information.
f Protocol The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”. •• MAC (Ethernet) Address : The MAC address imprinted on
the camera label is automatically displayed and requires no
DDNS URL address enabling access from the external Internet. user setting.
g URL However, this will be replaced with the <IP Address> of the camera if DDNS registration
has failed. MM `` IP related parameters can be set only when DHCP is not checked.
h IPv4 Scans for cameras with the IPv4 setting.

If not using a Broadband Router If the Broadband Router has more than one camera connected
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator. Configure the IP related settings and the Port related settings distinctly with each other.
4. In the <Port> pane, provide necessary information. ex)

•• HTTP Port : Used to access the camera using the Internet Category Camera #1 Camera #2
browser, defaulted to 80.

•• VNP Port : Used to control the video signal transfer, IP Address 192.168.1.100 192.168.1.101
defaulted to 4520. IP related settings Subnet Mask 255.255.255.0 255.255.255.0
Gateway 192.168.1.1 192.168.1.1
5. Enter the password.
Enter the password of “admin” account, which was used to
access the camera. HTTP Port 8080 8081
Port related settings
VNP Port 4520 4521
JJ `` For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and lowercase and
the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar of the Internet browser
special characters for your password.
`` If you want to change the password, refer to “Administrator password change” of the user setup. (page 39)
MM `` Ifbefore you can access the camera.
ex) http://IP address : HTTP Port
6. Click [OK]. http://192.168.1.100:8080
Manual network setup will be completed.
Auto Network Setup
If using a Broadband Router Run <IP Installer_v2.XX.exe> to display the camera search list.
•• IP Address : Enter an address falling in the IP range provided At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
by the Broadband Router.
ex) 192.168.1.2~254, 192.168.0.2~254, MM `` For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.
192.168.XXX.2~254
1. Select a camera in the search list.
•• Subnet Mask : The <Subnet Mask> of the Broadband Router
Check the MAC address of the camera on the camera’s label.
will be the <Subnet Mask> of the camera.
Both the [Auto Set] and [Manual Set] buttons will be
•• Gateway : The <Local IP Address> of the Broadband Router activated.
will be the <Gateway> of the camera.
2. Click [Auto Set].
MM `` The settings may differ depending on the connected Broadband
Router model.
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>, and <Gateway> will
For more information, refer to the user manual of the applicable router. be set automatically.
`` For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”. 3. Enter the password.
(Page 28) Enter the password of “admin” account, which was used to
access the camera.
JJ `` For the security purposes, you are recommended to use a

combination of numbers, alphabets uppercase and lowercase and
special characters for your password.
`` If you want to change the password, refer to “Administrator
password change” of the user setup. (page 39)
4. Click [OK].
Auto network setup will be completed.
English _27
Dynamic IP Setup 3. When done, click [Save Settings].
Your settings will be saved.
Dynamic IP Environment Setup

•• Example of the Dynamic IP environment
MM `` Above sample instructions are based on the CISCO’s Broadband Router.
`` The settings may differ depending on the connected Broadband Router model.
-- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server For more information, refer to the user manual of the applicable router.
-- If connecting the camera directly to modem using the DHCP protocols
-- If IPs are assigned by the internal DHCP server via the LAN
Setting up Port Range Forward for several network cameras
Checking the Dynamic IP •• You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page.
1. Run the IP Installer on the user’s local computer. •• A user can change each port using the camera setting screen.
Cameras allocated with <Dynamic IP> address are shown in When Camera1 and Camera2 are connected to a router :
the list.
2. Select a camera from the search result.
3. Click the [Manual Set] button and check the camera’s
<Dynamic IP> address.
User
 Internet
If you uncheck <DHCP>, you can change IP to <Static>.
 Camera1 (192.168.1.100)
Broadband Router HTTP port 8080
Start
3000
End
3000
Protocol
TCP/UDP
IP Address
192.168.1.100
 Device port 4520
RTSP port 3000
3001 3001 TCP/UDP 192.168.1.101
4520 4520 TCP/UDP 192.168.1.100
Camera2 (192.168.1.101)
4521 4521 TCP/UDP 192.168.1.101
HTTP port 8081
8080
8081
8080
8081
TCP/UDP
TCP/UDP
192.168.1.100
192.168.1.101
 Device port 4521
RTSP port 3001
Port Range Forward (Port Mapping) Setup
If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the
Broadband Router so that a remote PC can access the camera in it.
MM `` Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function.
After connecting the network camera, select the checkbox from the menu <Quick connect> in <Wisenet DDNS> in
“Settings -> Network -> DDNS”.
Manual Port Range Forwarding
1. From the Setup menu of the Broadband Router, select
<Applications & Gaming> - <Port Range Forward>.
For setting the port range forward for a third-party Broadband
Router, refer to the user guide of that Broadband Router.
2. Select <TCP> and <UDP Port> for each connected camera
to the Broadband Router.
The number of each port to be configured to the IP router
should be set according to the port number designated
in <Setup> - <Basic> - <IP & Port> on the camera web
viewer.

Connecting to the Camera from a Shared Local PC
1. Run the IP Installer.
It will scan for connected cameras and display them as a list.
2. Double-click a camera to access.
The Internet browser starts and connects to the camera.

MM `` Access to the camera can also be gained by typing the camera’s IP
address in the address bar of the Internet browser.
Connecting to the Camera from a Remote PC via the

Internet
Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not
allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL.
1. Before you can access a camera in the Broadband Router network, you should have set the port range
forward for the Broadband Router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the
IP address of the Broadband Router in the address bar.
ex) http://ddns.hanwha-security.com/ID
MM `` For registering the DDNS settings, refer to “Registering with DDNS”. (page 48)
English _29
web viewer
Connecting to the Camera Connecting via Bonjour
1. Run the client or operating system in support of the Bonjour protocol.
Normally, you would 2. Click the camera name for search.
1. Launch the Internet browser. In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.
2. Type the IP address of the camera in the address bar. -- The login window is displayed.
ex) • IP address (IPv4) : 192.168.1.100 
http://192.168.1.100 To check the DDNS address
- the Login dialog should appear.
If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE modem, the IP
• IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111
address of your network will be changed each time you try to connect to the ISP (Internet Service Provider)
 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login
server.
dialog should appear.
If this is the case, you will not be informed of the IP address changed by DDNS.
If the HTTP port is other than 80 Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP
when you try to access the device.
1. Launch the Internet browser. To register your device to the <DDNS> server, visit http://ddns.hanwha-security.com and register your device
2. Type the IP address and HTTP port number of the camera in the address bar. first, and then set the Web Viewer’s <Network> - <DDNS> to <Wisenet DDNS>, as well as providing
ex) IP address : 192.168.1.100:HTTP Port number(8080) <Product ID> that had been used for DDNS registration.
 http://192.168.1.100:8080 - the Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
ex) URL address : http://ddns.hanwha-security.com/ID
- the Login dialog should appear.
JJ `` Network connection is disabled in the LAN only environment.

Connecting via UPnP
1. Run the client or operating system in support of the UPnP protocol.
2. Click the camera name for search.
In the Windows operating system, click the camera name searched from the network menu.
-- The login window is displayed.
30_ web viewer

Password setting Plug-in support specifications for each browser
When you access the product for the first time, you must register the The existing plug-in web viewer and a new plug-in free web view is embedded together.
login password. This allows you to use the web viewer in newer browser environments that do not support plug-ins, such as
When the “Password change” window appears, enter the new Chrome, EDGE, FireFox (Windows 64-bit only), and Safari. For browsers that allow the installation of plug-ins,
password. such as IE and Safari, installing the plug-in is recommended.
●● web viewer
According to the browser environment, the following differences may be observed.
JJ `` For a new password with 8 to 9 digits, you must use at least 3 of

the following: uppercase/lowercase letters, numbers and special
•• Chrome, FireFox(Windows 64bit only), EDGE browser : Although they don’t support plug-ins, you can
use a web viewer as a plug-in free web viewer is embedded.
characters. For a password with 10 to 15 digits, you must use at
least 2 types of those mentioned.
-- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ JJ `` Asquality
the plug-in free webviewer has lower performance than the plug-in webviewer, it has a limit on the monitoring of high
profiles and playback of saved videos.
To monitor high quality profiles and play saved videos, use either a plug-in webviewer or SmartViewer.
`` For higher security, you are not recommended to repeat the same characters or consecutive keyboard inputs for your
passwords. -- Plugin-free webviewer creation conditions: The selected profile exceeds MJPEG Full HD 10fps H.264 (Chrome : full screen
resolution supported / Edge, Firefox, Safari : Full HD 30 fps or higher) H.265 FullHD 10fps 2Mbps or higher
`` If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose your password by using a
memo pad or memorizing it. -- Plugin-free playback conditions: MJPEG/H.264 full screen resolution, H.265 HD or below
`` The plug-in free feature has been optimized for the Chrome browser.
Login `` Supports Adaptive Streaming
-- This is the feature that automatically lowers the profile if there is a delay of more than 5 seconds. It was made to prevent
Whenever you access the camera, the login window appears. issues such as increased latency and no response from the browser when playing the video on a system with lower hardware
Enter the User ID and password to access the camera. specifications than recommended.
The video profile is reduced in the following sequence: 1920X1080(20fps) -> 1280X720(20fps) -> 640X480(20fps).
1. Enter “admin” in the <User name> input box.
The administrator ID, “admin”, is fixed and can not be `` In the following cases, the detection performance may be impaired or an malfunction may occur.
changed.
-- Monotonous monitoring environment, night or low illumination environment
2. Enter the password in the <Password> input field.
-- Severe camera wobbling and sudden changes in illumination
3. Click [OK].
If you have logged in successfully, you will the Live Viewer •• IE, Safari browser : You can use a web viewer even if you don’t install the existing plug-in web viewer.
screen.
JJ ```` ToIn themonitor/play saved video seamlessly, you are required to install a plug-in.
JJ `` When you access the camera web viewer, pay special attention to the
security by checking whether the image data is encrypted.
following cases, the detection performance may be impaired or an malfunction may occur.
`` If you check the “Remember my credentials” option when your input is done, in future you will be logged in automatically -- Severe camera wobbling and sudden changes in illumination
MM without being prompted to enter the login information.
`` You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut the image on the borders.
English _31
web viewer
Installing WebViewer Plugin Using the Live Screen
To access to the plug-in webviewer and play a live video (H.264/H.265) or a recorded video, an installation
message will be prompted. At this time you need to install the webviewer plug-in to use the function properly. a b c d e f
1. When the monitoring page is accessed for the very first time, the installation page is displayed. Click
[Download plugin] to begin installation.
JJ `` If“Release
the plug-in installation file download status is suspended at 99% in the Internet Explorer browser, retry it after selecting
SmartScreen filter” in “Tool  SmartScreen filter”.
2. Click [Run] in the message window.

3. Click [Yes] when the notice window saying that all browser windows will be closed.
MM `` Steps 4 and 5 will be skipped if no Web Viewer Plug-in is installed.

4. When the old version of the Web Viewer Plug-in is installed, a notice window saying the old version will be
deleted is displayed.
Click [Yes] when the notice window is displayed.
5. Click [OK].
The old version of Web Viewer Plug-in is deleted.
6. Click [Install] to begin installation of the Web Viewer Plug-in.
7. Click [Finish].
Web Viewer Plug-in installation is completed.
JJ `` Inwebviewer_activexplugin_lib.control
your internet explorer, if you need to move to the installation screen after installing the webviewer plugin, check whether
in the “Tool  Additional Function Management” menu is “Activated”. If not, and if there
is a persisting problem, then select “Tools  Internet Options  General” and delete all the search records.
If the problem persists, please register the IP or Domain of your camera in “Tools  Internet Options  Security  Trusted
sites”. g h i j klmn o p
Item Description
Using a Plug-in Free Webviewer
a Live Moves to the Live screen.
Although it is not possible to install plug-ins separately If you access the camera from Google Chrome, Mozilla
Firefox, or the MS Edge web browser, you can view and control the camera video without installing plug-ins. Move to the screen where you can search for the video recording saved in your Micro SD memory
b Playback
1. Enter your username and password to log in. card or NAS.
2. When you are logged in, a camera live view screen appears. Setup Move to the Setup screen.
c
Displays the Live video on the screen.
d Viewer Screen
`` You can use the mouse wheel to activate the digital zooming in Viewer screen.
Webviewer plug-in
e You can install webviewer plug-ins to play live or recorded videos (only available in IE and Safari).
installation
f Online help The Online help provides detailed descriptions for each function.
32_ web viewer

You can select a profile type in <Video profile> under the <Basic> setup menu. Alarm output Activate the Alarm Out port.
o
`` Click the icon to display the name of the current profile.
p Audio control Activates audio and adjusts the volume.
JJ ` Afterimages can be displayed on the screen under the following conditions if the video is
g Profile type
●● web viewer
played in the monitoring page:
-- The resolution is changed due to a profile change.
-- Incoming data is being slowed due to a network delay when the profile is changed. JJ `` Some functions may not work on a specific browser or codec.
-- The web browser window size and location is changed.
Controls the PAN/TILT/ZOOM motion. To capture the snapshot
Drag the bar on the right side of the UI up, or click the [ ] button 1. Click [Capture ( )] on the scene to capture.
Zoom In ( )
to zoom in the screen. 2. When a captured video is saved, a notification message appears.
The farther the bar position is from the center, the faster the screen The captured image is saved in the designated folder for each browser.
will be zoomed in.
h PTZ
Drag the bar on the right side of the UI down or click the [ ] MM `` If the screen is not captured by IE browser in Windows 7 or higher, run the IE Browser with the Admin privilege.
button to zoom out the screen.
Zoom Out ( )
The farther the bar position is from the center, the faster the screen To save
will be zoomed out.
1. Click the [Record ( )] icon.
Move screen ( ) Moves in the direction where the cursor is located.
2. To end the recording, press [Record ( )] again.
Click the icon to turn it ON, and the camera will track a moving
Auto tracking ( )
person or object automatically.
MM `` You can save the recorded file on the PC in an avi file format. Designate a path and save the video.
i Profile access information You can read the profile information.
To fit the full screen
Double click on the video screen, and the current video will be
Full Screen ( ) 1. Click the [Full Screen ( )] icon.
played in the full screen of the monitor.
2. This will fit the Viewer to the full screen.
A view mode in which the size of the camera video automatically fits
Fit to screen ( ) 3. To leave full screen mode, click the [Full Screen ( )] button again or press the [Esc] key on the
to the web browser size.
j Switch View Mode keyboard.
Size of the original file
View mode in which the video is played in the actual resolution.
( )
To Use Audio
Maintain Aspect Ratio
View mode that adjusts the aspect ratio to best fit the resolution. 1. Click [Audio ( )] icon to activate audio communication.
( )
2. Use [ ] bar to control the volume.
k Capture Saves the snapshot as an image file in the .png format.
If there is no sound from pulling in and out the audio jack while it is in operation, click the [Audio ( )] icon to enable it
l Record The user can save the video on the PC. MM `` again.
Pixel Counter Checks the number of pixels in the selected area on the video screen. `` To use audio, you need to set <Audio in> in “Video Profile” to <Enable> (page 37).
m
n Microphone control Activates the microphone.
English _33
web viewer
To Use Microphone To check the profile status
Click [Mic ( )] icon to activate the microphone. You can check the profile information.
MM `` If you are using IE or the Safari browser, you will need to install plug-in.
To count the number of pixels
1. Click the [Pixel count ( )] icon to activate it. 1. Click the [Status ( )] icon.
2. Drag the mouse on the video to select an area. 2. The profile access information screen is updated whenever the screen is enabled.
3. The number of pixels in the selected area is displayed on the screen. •• Profile access : Show the information of the newly added profile.
-- Profile : Show the information of the newly added codec.
To control PTZ -- Bitrate(kbps) : Show both the actual bit rate and the set bit rate.
-- Framerate(fps) : Show both the actual frame rate and the set frame rate.
1. Click the [PTZ ( )] icon.
-- ATC(%) : Show the ATC status.
2. Move the cursor of the Move Screen pad [ ] to move the camera direction or adjust the zoom or focus.
-- Concurrent users count : Show the number of concurrent users who access the profile.
•• Current users : Shows information on users accessing web viewer and displaying monitoring video.
-- Profile : Show the name of the profile accessed by the user.
-- Bitrate(kbps) : Show the current bit rate.
-- Network connection status : It shows whether the network is working fine.
-- IP address : Show the IP address of the current user.
34_ web viewer

Playing the recorded video Item Description
e Search range setting Set the search date and time range for data saved in your Micro SD memory card or NAS.
MM `` Before you can play the video, you must configure the record settings. For details on record settings, refer to “Storage”. (page 52)
Saves the current video screen in an image file format (format may vary depending on the
Capture
Playback Screen Name and Features f browser).
●● web viewer
Set the desired date to make a backup copy of video data saved in your Micro SD memory card
g Backup or NAS.
`` You can set up to 5 minutes for the backup of a saved video.
To listen to a voice signal (if present) in the recorded video, then activate the voice signal icon
h Audio
when you play it.
i Viewer Screen The recorded video will appear.
To play the content after searching by event

1. On the Playback screen, click the [Show ( )] button.
2. If there is a video recorded on the date of search, the
applicable video is displayed on the time bar.
3. To perform a search by event type, click the [All] button at
the top of the time bar and select an event type.
4. When done, click [Apply].
Event searched is displayed on the time bar.
5. Click the [Play ( )] button.
6. To pause the video, click the [Pause ( )] button.
a b cd e f gh i
Item Description
a Time Bar Move the time bar to play the video at a desired time.
The contextual menu screen at the bottom will disappear, and only the menu icon will be
b Hide the context menu
displayed.
c Search event setting Set the event type to search within the search period.
Double click on the video screen, and the current video will be
Full Screen ( )
played in the full screen of the monitor.
A view mode in which the size of the camera video automatically fits
Fit to screen ( )
to the web browser size.
d Switch View Mode
Size of the original file
View mode in which the video is played in the actual resolution.
( )
Maintain Aspect Ratio

View mode that adjusts the aspect ratio to best fit the resolution.
( )
English _35
web viewer
To play after searching by time To Play an AVI File
1. Click the [ ] icon. (1) Micro SD memory card
2. On the calendar, set the search date, start time and end time.
The event searched is displayed on the time bar. 1. Separate the Micro SD memory card from the camera.
3. Click the [Play ( )] button.
The video at the selected time will be played. JJ `` Before separating the Micro SD memory card, set the <Device> to <Off> in the “Setup  Event  Storage” menu.
4. When a video is played, the recording time of the video 2. Insert the Micro SD memory card into the PC.
currently being played is displayed. 3. Play the AVI file in the “\ch00\img\YYYY_mm_DD\AVI”
5. Search the video forward and backward and adjust the directory, using a media player.
playback speed.
-- How to Move Playback Interval
Select the [ , ] button to move 1 frame forward/
MM `` Aandfilename starts with the format “001_YYYYMMDD_HHMMSS.avi”
the file number is incremented by one.
backward. YYYYMMDD_HHMMSS indicates the start time of data saving.
-- How to Control Playback Speed `` “001_YYYYMMDD_HHMMSS.smi” file is a caption file, and you can
Click the [ ] button and you can select a speed of view it if it exists in the same directory as its related AVI file.
either 1x, 2x, 4x and 8x or -1x, -2x, -4x and -8x, and you can set the playback speed as desired.
`` The max recording time per AVI file is 5 minutes.
6. Move the position of the [Time Bar ( )] to play the video at a desired time.
`` Once corrupted, the data in the Micro SD memory card cannot be
replayed in the Web Viewer’s [Playback].
To back up the searched video
1. During playback, click [Backup] on the scene to back up.
The data in the applicable section will be backed up.
2. Click [Apply] button.
The Save As window appears. (2) NAS (Network-Attached Storage)
3. Confirm the save path and click [Save] button.
The screenshot will be backed up to the specified path. 1. In Windows browser, use \\<ip address>\ to access.
ex)\\192.168.20.31\defaultfolder\ch01\img\2013_07_02\AVI
2. Go to <Computer>  <Network drive connection> 
Enter 1.
3. Connected to the NAS.
The directory structure is same as the directory structure for a
Micro SD memory card.
MM `` Aandfilename starts with the format “001_YYYYMMDD_HHMMSS.avi”

the file number is incremented by one.
YYYYMMDD_HHMMSS indicates the start time of data saving.
To play the backup video `` “001_YYYYMMDD_HHMMSS.smi” file is a caption file, and you can
view it if it exists in the same directory as its related AVI file.
The backed up images are saved in an .avi format. Installing the media player that supports the format for the
user PC is recommended. `` The max recording time per AVI file is 30 minutes.
`` If you change or damage the saved data on your own, it will not play back or save properly.
`` If playback does not run smoothly due to the user environment, optimizing by installing the latest codec and other methods
MM are required.
36_ web viewer

setup screen
Setup 7. According to your situation, set ATC (Auto Transmit Control) mode.
•• ATC mode : It adjusts the video properties according to the
You can configure the basic camera information, PTZ, video and audio, network, event, analyze and system variance in the network bandwidth, controlling the bit rate.
settings. Adjusting the bit rate depends on the ATC mode.
-- Control framerate : Reduce the frame rate if the network
1. On the live screen, click the [Setup ( )] button. bandwidth drops down.
●● setup screen
2. The Setup screen appears.
-- Control compression : Control the compression rate if the network bandwidth drops down.
Compression adjustment can cause deterioration of the image quality.
Basic Setup -- Event(MD) : Activated when the motion detection (MD) event is set. Frame rate is adjusted when an
event occurs.
If no motion is detected in the surrounding area, the minimum amount of frames is output to save the
Video profile bandwidth use.
1. From the Setup menu, select the <Basic ( )> tab. `` If <Bitrate control> is set to <CBR>, the encoding priority according to the ATC mode will be fixed as below:
2. Click <Video profile>.
Bitrate control / ATC mode Control framerate Control compression Event(MD)
3. Set the <Video profile connection policy>.
•• Keep connection when profile setting is changed : Output CBR Compression Framerate Framerate
uses the same settings even when the settings of the
•• Sensitivity : Affect the transfer rate according to the variance in the network bandwidth.
active profile are changed.
The transfer rate will be adjusted to the fastest if the bandwidth is <Very high>, and adjusted to the
If not selected, changing a profile used by an existing
latest if the bandwidth is <Very low>.
connection resets such connection.
•• Limit : If the quality or frame rate is adjusted, the property will be changed to the applied value (%)
4. Select each profile properties. against the previous setting value (100%).
For more details, refer to “To Add/Change the Video Note that if you reduce the property value too much, you may encounter flickering on the screen. So it
Profile”. (Page 38) is advisable to adjust the value within the threshold.
5. Click the input box of each item and enter / select a desired
value. JJ ```` ItSetis the
recommended to apply ATC control only for cameras supporting ATC.
ATC sensitivity to <Very low> in a network environment with high variance in the network bandwidth.
`` The context menu may differ depending on the selected codec type.
•• Default profile : If no profile is selected when using the Web `` If the network connection is unstable, you may encounter flickering on the screen.
Viewer, the default video profile is applied.
8. Select Able or Disable for the Crop Encoding function.
•• E-mail/FTP profile : Video profile to be transferred to the specified email or FTP site. For more details, refer to “To Use Crop Encoding”. (Page 39)
`` Only the MJPEG codec can be set as the E-mail/FTP profile. •• Crop encoding : It cuts only the selected area out of the full screen and outputs it at the resolution
•• Record profile : This is the profile that is applied to video recording. specified in <Profile setting>.
•• DPTZ Profile : Profile applied when using the PTZ. The resolution should be less than the Crop Encoding setting area.
`` To use PTZ, add a DPTZ profile. 9. When done, click [Apply].
6. Select whether or not to input audio in the video.
Select the <Audio In> check box and you can input audio in the video.
English _37
setup screen
To Add/Change the Video Profile •• Dynamic GOV : When the bit rate control is VBR in H.264/H.265 codec, it makes the GOV length
automatically change to the set value of the maximum dynamic GOV.
The profile setup can be added or modified to accommodate various profiles depending on the recording
conditions. •• Dynamic FPS : Set the FPS value to automatically change the setting of the FPS value to the maximum
dynamic value when the bit rate control is VBR between H.264/H.265 codec.
1. In <Video profile>, click the <Add> button. •• Multicast(RTSP) : Specify the use of the RTSP protocol.
2. Provide the name and select a codec. -- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.
3. Specify the conditions under which the codec will be applied. -- Port : Specify the video communication port.
4. Specify the details of the selected codec including resolution and frame rate. -- TTL : You can set the TTL for the RTP packet.
•• Resolution : Set the video size of the H.264/H.265 and MJPEG files.
•• Framerate : Set the max number of video frames per sec.
JJ `` Ifcase,
you set the Multicast address to 224.0.0.0~224.0.0.255, multicast may not work properly in all environments. In that
we recommend you change the multicast address.
`` The Sensor mode setup in Camera Setup changes the maximum configurable framerate.
MM
Sensor 25 fps 30 fps 50 fps 60 fps What is GOV length?
Framerate 1~25 fps 1~30 fps 1~50 fps 1~60 fps GOV(Group of Video object planes) is a set of video frames for H.264/H.265 compression, indicating a
collection of frames from the initial I-Frame to the next I-Frame. GOV consists of 2 kinds of frames: I-Frame
•• Maximum bitrate : Set the max bit rate of video when the bit rate control is set to VBR.
and P-Frame.
JJ `` Ascanthebe bitgreater
rate can be adjusted limitedly according to the resolution, frame rate and screen complexity, the actual bit rate
than the maximum bit rate. So you must consider the use conditions when setting the value.
I-Frame is the basis frame of compression, and contains data for a completed single image. P-Frame
contains only the data that has changed from the preceding I-Frame.
•• Target bitrate : Set the target bit rate when the bit rate control is set to CBR. For H.264/H.265 codec, you can determine the GOV length.
•• Bitrate control : You can select one from constant bit rate and variable bit rate for compression. Fixed If you set a recording profile with H.264/H.265 codec, the GOV length will be framerate/2.
bitrate means that the network transmission bitrate is fixed while varying the video quality or frame rate,
variable bitrate means that a higher priority is placed on the video quality while varying the bitrate.
What is dynamic GOV?
Dynamic GOV is a function that enables the GOV to automatically change in a range from the set value of the
JJ `` After setting the fixed bit rate for bit control, if you select the video quality priority mode, depending on the complexity of
the screen, the actual transmitted frame rate may differ from the frame rate setup in order to guarantee the optimal video
minimum GOV length to the maximum dynamic GOV set value according to the situation of the video.
quality for the given bit rate. In a video with almost no motion, GOV operates with the dynamic GOV settings, which makes the bit rate of
the entire video reduced. The I-frame is output right after a motion is detected and GOV operates with the
•• Encoding priority : You can set the priority of video transmission to frame rate or compression. GOV length settings until the motion disappears.
•• GOV length : It specifies the distance (in terms of number of frames) between two consecutive I-Frames If you use this function, the GOV of a video operates with the minimum GOV length settings.
in a video sequence when H.264/H.265 codec was selected. (One I-Frame + 0~Several P-Frames)
•• Profile : You can select the H.264/H.265 profiling method.
•• Entropy coding : Reduce the possible compression loss due to encoding.
•• Smart codec : Specify the use of Smart codec.
MM `` You can use this when the bit rate control value is CBR. Detailed settings are configured in the Smart Codec on the
Audio & Video tab. (Page 47)
38_ setup screen

To Use Crop Encoding User
1. Select <Enable>. 1. From the Setup menu, select the <Basic ( )> tab.
2. Click <Set area>. 2. Click <User>.
The Crop Encoding Area Setup window will pop up. 3. Provide the necessary user information.
•• 16:9 : The aspect ratio shall be set to 16:9 as close as to •• Administrator password change : Change the password
●● setup screen
the user specified area. for the administrator.
The supporting size ranges from 640X360 to 1280X720
and supporting output resolutions are 640X360, 800X448,
1280X720.
JJ `` For the security purposes, you are recommended to use a
combination of numbers, alphabets uppercase and lowercase
•• 4:3 : The aspect ratio shall be set to 4:3 as close as to the and special characters for your password.
user specified area. `` It is recommended to change your password once every three
The supporting size ranges from 320X240 to 1280X960 months.
and supporting output resolutions are 320X240, 640X480,
800X600, 1024X768, and 1280X960. `` The password length and limits are shown as follows.
•• Manual : It sets up the aspect ratio of the user specified -- A combination of at least three types of upper case, lower case, numeric, and special characters: 8 to 9 characters.
area. -- A combination of at least two types of upper case, lower case, numeric, and special characters: 10 to 15 characters.
The supporting size ranges from XND-6080/6080V/6080R/6080RV, XNV-6080/6080R: 320X240 ~ -- Should be different from the ID.
1280X1024 / XNV-8080R, XND-8080R/8080RV: 320x240 ~ 1600x1200 and all supporting output
-- Cannot repeat the same letter, number of special characters more than 4 times.
resolutions are available except 1920X1080.
-- Don’t use 4 or more characters consecutive together. (examples : 1234, abcd)
3. Drag the mouse on the screen to specify the Crop Encoding area at your discretion.
-- Don’t use 4 or more characters repeated. (examples : !!!!, 1111, aaaa)
JJ `` Iftheyouimage
set output as <Manual>, you can specify a desired range. However, if output is only available at a supported resolution,
will be output at the resolution that is closest to the range that you specified.
--
--
Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
After the factory setting, the admin and user passwords are initialized. You need to reset the password.
`` The Crop Encoding area setup can change depending on the DIS setup. Reset the Crop Encoding area when the DIS setup is -- When you access the camera web page for the first time or access it after the initialization, you will be moved to the
changed. admin password setting menu.
-- In this menu, you need to login again with the new password before using the camera web page menus.
-- If the existing password is not matched, when you change the admin password, you cannot change the password.
-- After changing your password, if there is a camera connected to a CMS or NVR client, then you need to re-register it
with the newly changed password. If the camera is still connected with the same password, then the account may be
locked because a client uses the previous password.
`` If you try to login with the registered account, 5 or more consecutive password authentication has failed, and then the
account may be locked for thirty seconds.
`` When the password is changed while multiple connections are active from a PC, the browser may malfunction. In that
case, reconnect to the server.
•• Guest setup : If you select <Enable guest access>, the guest account can access the Web viewer
screen but can only view the live Viewer screen.
`` The ID/password for the guest account is <guest/guest>, which cannot be changed.
•• Authentication setup : If you select <Enable RTSP connection without authentication>, you can
access RTSP without logging in and view the video.
English _39
setup screen
•• Current users : If you select <Use>, you can set or change the user permissions. IP & Port
`` The administrator can set the audio input, audio output, alarm output permissions.
1. From the Setup menu, select the <Basic ( )> tab.
`` Audio input/Audio output/Alarm output : You can enable/disable Audio input/Audio output/Alarm output in the live mode on the
current user account. 2. Click <IP & Port>.
`` Profile : If you select <Default>, you can only see the default profile video; if selecting <All>, you can see the full profile 3. Click <IP address>.
videos. 4. Set the <IPv4 setup>.
•• IP type : Select an IP connection type.
JJ `` ONVIF functions available to a registered user allowed to use ONVIF functions are limited to those of granted with permission. -- Manual : Specify the IP address, Subnet mask,
Gateway, DNS1, and DNS2.
4. When done, click [Apply]. -- DHCP : Specify the DNS1 and DNS2.
-- PPPoE : Specify the DNS1, DNS2, ID and Password.
Date & Time
`` If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.
1. From the Setup menu, select the <Basic ( )> tab.
•• MAC address : Shows the MAC address.
2. Click <Date & Time>. •• IP address : Displays the current IP address.
3. Specify the time and date that will be applied to the camera. •• Subnet mask : Displays the <Subnet mask> for the set IP.
•• Current system time : Displays the current time settings of •• Gateway : Displays the <Gateway> for the set IP.
your system. •• DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
•• Timezone : Specify the local time zone based on the GMT.
5. Set the <IPv6 setup>.
•• Daylight saving time : If checked, the time will be set one
hour before the local time zone for the specified time
`` Set to <Use> to use IPv6 address.
period. •• Default : Use the default IPv6 address.
This option will be displayed only in areas where DST is applied. •• DHCP : Display and use the IPv6 address obtained from the DHCP server.
•• System time setup : Specify the time and date that will be applied to your system. •• Manual : Enter IP address and gateway manually and use it.
-- Manual : Sets the current time of the camera manually.
When you select the <Synchronize with PC viewer> check box, the time of the webviewer is set to
the time displayed on the PC that runs the webviewer. JJ `` The IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous settings will be restored
automatically.
-- Synchronize with NTP server : Sync with the time of the specified server address. `` Once completed with editing, click [Apply] to apply changes and the browser exits. After a while, connect again with the
changed IP.
JJ `` IfPC.you select the <Synchronize with PC viewer>, the standard timezone should be set the same as the current timezone in
40_ setup screen

6. Click <Port>. PTZ setup
7. Type in each item in the Port menu as necessary.
`` Neither the port range between 0 and 1023 nor port 3702 is available. Digital PTZ
•• HTTP : HTTP port used to access the camera via the web Use this settings page to move the camera view and perform the digital zoom.
browser.
The default is 80(TCP).
JJ `` <DPTZ profile> from <Video profile> should be selected for the setting.
●● setup screen
`` Setting the HTTP port for Safari and Google Chrome browsers to
1. From the Setup menu, select the <PTZ ( )> tab.
65535 is not allowed by security policy.
•• HTTPS : In this version, the security of the web communication protocol HTTP is strengthened. It can 2. Click <Digital PTZ>.
be used when you set HTTPS mode in SSL.
To add a preset
The initial value is set to 443(TCP).
`` The available setting range is 1024~65535. (For security reasons, in your Safari or Google Chrome browser, you may not use 1. Select the preset number to add.
65535 as your HTTPS port.)
2. Set the name for the preset.
•• RTSP : Used to transfer videos in the RTSP mode; the default is 554.
3. Press the [Add] button.
•• Timeout : When connecting to RTSP, this function resets the connection if there’s no response for a
certain time. To delete a preset
1. Select the preset number to delete.

MM `` IfAfterwards,
changed the HTTP port, the browser exits.
address should contain the newly assigned HTTP port trailing the IP. 2. Press the [Remove] button.
ex) IP address: 192.168.1.100, HTTP port : Assigned 8080  http://192.168.1.100:8080
(If HTTP port is set to 80, no need to specify the port number) To move to a desired preset
`` Using RTSP and HTTPS is recommended in order to prevent the image information from being restored. 1. Select a preset number that you want to move.
8. When done, click [Apply]. 2. Press the [Go] button.
To set a group
The group function enables you to group various presets before calling them in sequence. Six groups can
save a total of 128 presets each.
1. Select a group setting mode.

2. Press the [Add] button.
Entered in the bottom list.
3. If you want to delete a preset added, select it and press the [Delete] button.
4. Press the [Start] button.
It performs the group operation.
5. Press the [Stop] button.
The running group will be stop.
6. Press the [Remove] button.
Selected group data will be deleted.
English _41
setup screen
Video & Audio setup Audio setup
You can configure the I/O settings of the audio source from the camera.
Video setup 1. From the Setup menu, select the <Video & Audio ( )>
1. From the Setup menu, select the <Video & Audio ( )> tab.
tab. 2. Click <Audio setup>.
2. Click <Video setup>. 3. Set the audio input value.
3. Select a <Video rotation> mode. •• Source : Sets the audio input.
•• Flip : Turn upside down the image that is captured by the -- Internal microphone : Built-in microphone embedded in
camera. the camera.
•• Mirror : Flip horizontal the image that is captured by the (only available in XND-6080/6080V/6080R/6080RV/8080R/8080RV)
camera. -- Line : Connect the cable to the audio device.
•• Hallway view : Rotates the video captured by the camera -- External microphone : Uses an external microphone.
according to the set angle.
You can rotate the video 0, 90 or 270 degrees. •• Apply power to Ext. Mic. : Select this check box when the external microphone is not powered, and the
power will be supplied from the camera to the microphone. You can configure settings when selecting
`` If you change settings, the browser window will be closed and the camera restarted. Please access again later.
<External microphone>.
4. Specify whether to use the analog video output function. •• Codec : Specify the audio codec.
`` To decrease the performance reduction, the usage should only be unlocked after installation. -- G.711 : A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding.
5. Select the video type. ITU standard audio codec that is adequate for digital voice transfer in PSTN network or through a
PBX.
6. Specify the privacy zone.
-- G.726 : ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code Modulation) for
`` You can set the pattern of the privacy area either to Opaque or Mosaic.
variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding.
7. When done, click [Apply]. -- AAC : Acronym of Advanced Audio Coding, which is an international standard designed to be the
successor of the MP3 format. You can use audio at a higher sampling rate than when you use the
To set the privacy zone existing G.711 or G.726 codec.
You can specify a certain area of the camera video to be protected for your privacy. •• Sampling rate : Refers to the number of times of sampling when digitalizing an analog soundtrack. The
higher this value is, the better the sound quality is.
1. Set it to <Enable Privacy area>. •• Bitrate : Set the bit rate to differentiate compression ratio if using G.726 codec.
2. Click [Apply]. •• Gain : Specify the audio input amplification.
3. Select 4 vertices on the screen with your mouse to specify
the area. JJ `` Sound quality deterioration or howling may occur if the loudness of the sound source or gain value were set excessively.
4. Enter the name and select the color, and then click [OK]. 4. Set the audio output level.
5. If you want to delete a name in the list, select it and click •• Enable : Sets whether to use audio output.
[Delete]. •• Gain : Specify the audio output amplification.
42_ setup screen

Camera setup •• User preset : Select it if you want to display video with settings chosen by you.
You can change the camera settings according to the environment where the camera is located.
JJ `` When selecting a mode other than the preset mode, you can’t set the shutter speed, AGC, SSDR, SSNR and color.
1. From the Setup menu, select the <Video & Audio ( )> 2. Set the camera item for each image preset mode.
tab.
3. Set the <Activation time>.
2. Click <Camera setup>.
•• Off : Your camera will execute a specific image preset operation at all times.
●● setup screen
3. Configure the settings as necessary of : Image preset mode, •• Only scheduled time : Your camera will execute a specific image preset operation for the time period set
Sensor, SSDR, White balance, Back light, Exposure, Day/ by you on each date.
Night, Special, OSD, Heater, IR
4. Click the [ ] button.
5. Set the <Mode> and <Time>.
`` If a certain time (timeout: 240s) is elapsed with your not pressing the
[Apply] button after changing the settings, your changes will not be 6. When done, click [Apply].
applied.
If you want to set an image preset

Users can set presets easily.
The selected image preset mode will be in operation during the configured period, but at other times the
values configured in the user preset mode are reflected.
1. Select a desired mode from the image presets.

•• Motion & Bright video : This is the factory setting for Initial setting for each image preset mode
your camera. Select it for video recording, focusing on
reproducibility. Minimum Maximum Prefer
Image preset AGC SSDR SSNR 2D SSNR 3D COLOR
•• Motion : Record a moving object clearly. If there are many shutter shutter shutter
moving objects, such as on a road or in a crowded place
Default Default
like a museum, select this option. Motion & Bright video 1/12000 1/60(1/50) Default (12) Default (12) Default (12) Default (50)
(1/5) (High)
`` Noise level can increase in a low illumination environment, and
JJ sensitivity can go down. Motion 1/30 1/12000 1/200
Default
(High)
Default (12) 4 4 Default (50)
•• Noise reduction : Select this when you need a video with low noise in the low illumination environment. Noise reduction 1/15 1/12000 1/60(1/50) Middle Default (12) Default (12) Default (12) Default (50)
•• Bright video : This makes the dark area in a full video brighter. Default Default
Bright video 1/12000 1/60(1/50) 18 Default (12) Default (12) Default (50)
`` Video contracts effects are reduced. (1/5) (High)
JJ Motion & Noise
1/30 1/12000 1/200 Middle Default (12) 4 4 Default (50)
•• Motion & Noise reduction : Use this when there are many moving objects, such as on a road or reduction
in a crowded place like a museum, or when you need a video with low noise in a low illumination
Default
environment. High definition 1/30 1/12000 1/200 18 4 4 Default (50)
(High)
•• High definition : Use it when there are many moving objects, such as on a road or in a crowded place
like a museum, or when you need to make a dark area in full video brighter. Default Default
Vivid video 1/12000 1/60(1/50) 18 Default (12) Default (12) 90
•• Vivid video : Makes the entire video displayed in vivid colors. (1/5) (High)
User preset Manual Manual Manual Manual Manual Manual Manual Manual
JJ `` The contrast of the video reduces and the color reproducibility becomes low.
MM `` The
use.
preset setup functions as an aid to users to configure setup. If you don’t want the preset function, deactivate it before
`` If you change the image preset, only shutter/AGC/SSDR/SSNR/COLOR are reset to the default value for each model.
`` The “Camera Setting” value does not change between presets.
English _43
setup screen
To Set the Sensor To Set BLC
It specifies how many frames the camera CMOS sensor will capture per second. You can specify a desired area on the video manually and set the area to be displayed more clearly.
1. Select <Sensor>. 1. Select <Back light>.

2. Select <Mode>. 2. Set <Mode> to <BLC>.
3. Set <BLC level>.
MM `` Refer to “Video profile” for the framerate setup range of the <Video profile> according to mode setup. (Page 37) You can change the level to adjust the brightness of the
monitoring area.
To Set SSDR 4. Set the <Top, Bottom, Left, Right> levels to specify the
target area.
In a scene where the difference between bright and dark is severe, you can increase the brightness of the
dark area alone to regulate the overall brightness.
1. Select <SSDR>.
JJ `` When setting BLC, a green box is displayed on the screen for 15 seconds.
`` To prevent malfunction at the time of BLC setup, the vertical space of the BLC area should be over 40 and below 60 while the
2. Set the SSDR use option to <Enable>. horizontal space over 30 and below 60.
3. Configure the <Level> and <D-Range> settings as
necessary.
HLC (Highlight Compensation) Setup
•• Level : Adjust the level of the dynamic range.
If a strong light like a streetlamp or vehicle headlight points toward the camera, the area can be set to be cut
•• D-Range : Select the amplitude area of the dynamic range.
off to prevent a saturated area on the monitor.
To Set White Balance 1. Select <Back light>.

You can correct the image colors based on white under any lighting conditions. 2. Set <Mode> to <HLC>.
•• HLC level : This adjusts the brightness level to cut off the
1. Select <White balance>. highlighted area.
2. Select <Mode>. •• Mask
•• ATW : Corrects the colors of the camera video -- Off : Does not block an area with a brightness that is a
automatically. certain level or higher.
•• Manual : You can adjust the red and blue gains of the -- On : Always blocks an area with a brightness that is a
camera video manually. certain level or higher.
•• Outdoor : Automatically corrects the video colors of the camera to be optimized to the outdoor -- Night only : No blocked area is generated if the surrounding environment becomes dark to a certain
environment. level.
•• Indoor : Automatically corrects the video colors of the camera to be optimized to the indoor -- All day : No blocked area is generated if the surrounding environment becomes dark or bright to a
environment. certain level.
•• AWC : Corrects the colors of the camera video to be optimized to the current lighting condition and •• Mask color : You can select the color of the blocked area.
screen mode. •• Mask tone : You can adjust the brightness of the color in the blocked area.
To obtain the optimal condition for the current lighting, put the focus of the camera to a white paper
•• Dimming : Detects an area on the screen with strong light, and adjusts the brightness and reduces the
and press the [Set] button. If the lighting environment is changed, you should readjust the settings
saturated area.
accordingly.
3. Set the <Top, Bottom, Left, Right> levels to specify the target area.
`` In AWC mode, click the [Set] button if you want to keep the white balance level of the current image.
MM
JJ `` When setting HLC, a green box is displayed on the screen for 15 seconds.
`` To prevent malfunction at the time of HLC setup, the vertical space of the HLC area should be over 40 and below 60 while
JJ `` The white balancing may not work properly in the following conditions:
If this is the case, switch to AWC mode. the horizontal space over 30 and below 60.
-- If the surrounding condition of the object is out of the temperature correction range
ex) Clear sky, sunset MM `` Atenvironment.
night operation, this function will be activated only if the incoming highlight exceeds a certain area in a low contrast
-- If the surrounding of the object is dark
-- If the focus of the camera directly faces the florescent lighting or if the camera is installed in a place of variable `` At night operation, HLC will not function in too a bright or too a dark scene.
illumination, the white balancing operation may be unstable. `` During daytime operation, HLC will not work in dark condition.
44_ setup screen

To Set WDR •• SSNR 2D Level : Adjusts the 2DNR level.
It displays a sharp image of the objects in a scene where both bright and dark areas exist. -- 2DNR : This is a method of reducing the noise by using the adjacent pixel information on a single
video frame.
1. Select <Back light>. If you increase the level, the noise will be reduced but the video may be blurred.
2. Set <Mode> to <WDR>. •• SSNR 3D Level : Adjusts the 3DNR level.
3. Select each item and set it properly. -- 3DNR : This is a method of reducing the noise by using multiple video frames.
●● setup screen
•• WDR level : Adjusts the intensity of backlight If you increase the level, the noise will be reduced but the video may drag.
compensation.
•• Iris : Select it to set the camera lens to auto or manual.
•• Auto : Detects the surrounding environment and automatically uses backlight compensation.
-- DC(Auto) : The iris is automatically adjusted to the amount of the surrounding light.
•• Turn off in low light : Does not use automatic backlight compensation when detecting a dark
environment. -- Manual : Sets the iris F-No to manual.
•• Turn off in B/W : Does not use backlight compensation when switching to B/W mode. -- P-Iris : This is the depth priority mode. You can close the shutter during the day to get good depths
and in the nighttime, you can open the shutter to get more lights.
JJ `` It is recommended to use WDR in the indoor environment. •• Iris F-No : Set up the F value of the iris.
`` Noise may exist between the dark area and the bright area in the WDR mode. •• AGC : Select AGC Control mode.
`` With WDR mode On or Off, the minimum, maximum and user-preferred shutter value will be reset. Adjust the gain value of the video (that, in particular, was recorded at a low contrast scene and had a
lower brightness level than normal) to control the video brightness.
`` If you use the P aperture lens manually or a shaking preventive shutter, the WDR performance is partially limited.
`` In WDR mode, noise may occur in the motion area.
JJ `` The image exposure can be saturated depending on the Shutter setup range.
`` It may take some time from the point when you enable the WiseNR mode to the point when the effect is actually applied/
To Set Exposure released.
You can adjust the exposure level of the camera. `` When the WiseNR mode is enabled, the identifiability of the video will be improved, but the noise may be increased as
well.
1. Select <Exposure>.
`` In a bright environment with less noise, WiseNR may not be so effective.
2. Select each item and set it properly.
•• Brightness : Adjust the screen brightness. `` With intelligent NR enabled, the motion detection in the video will be performed according to the operation conditions
of the motion detection event, as motion detection uses the motion detection function internally. For more information,
•• Minimum shutter : The limit of the longest exposure time.
please refer to “Motion detection” (page 56).
`` Shutter is the mode to set up the range of the sensor exposure time
which will specify the upper and lower limits for the electronic shutter
movement. To Set Day/Night
`` The framerate may be reduced in the dark condition if Shutter has a 1. Select <Day/Night>.
lower value than specified in the Sensor mode.
•• Maximum shutter : The limit of the shortest exposure time. •• Mode : Mode is used to adjust the color of Color or Black
•• Prefer shutter : Sets an appropriate exposure duration that is preferentially applied within the exposure and White.
duration range. -- Color : The video is always output in color.
•• Anti flicker : It prevents screen flickering incurring from the dissonance between the surrounding lighting
-- B/W : The video is always output in black and white.
and the frequency.
•• SSNR -- Auto : Normally, it is set to Color but to B&W under low
luminance at night.
-- On : Noise of the video is removed.
`` If AGC of the <Exposure> menu is set to <Off>, the day/night
-- Wise NR : Automatically adjusts the nose reduction level when there is a moving object in the video mode cannot be set to <Auto>.
to increase the identifiability.
English _45
setup screen
-- External : It controls the color of the video when the alarm input terminal is synchronized with an To Set OSD
external device.
1. Select <OSD>.
-- Schedule : Set the time during which the camera is operated in the color mode.
•• Dwell Time : It specifies the period for which the selected brightness condition must be maintained to
•• Camera title : It specifies the name of the camera to be
switch the lighting mode from Day to Night or vice versa.
displayed on the screen.
•• Duration : It specifies the interval of lighting mode conversion. Select the <Use> check box to add a camera name.
•• Alarm in : The video is set to Color or B/W as the alarm sensor is open or closed. -- Add : Click the <Add> button and you can add a
`` If the Day/Night mode is set to External Input, the alarm input function of the Event-Alarm Input page is disabled. total of 5 lines, 15 characters per line and a total of 60
•• Activation time(Color) : It specifies the schedule for color mode operation. characters.
`` If it is set, the Color mode is maintained from 00 second of the starting time to 59 second of the ending time. -- Preview : Click the <Preview> button to check the name of camera that will be displayed on the
screen.
•• Camera title X, Y : It specifies the position of the camera name on the screen.
JJ `` When you switch to day/night mode, motion detection mode does not work. •• Date & time : Set the time display and date formats on the screen.
•• Date & Time X, Y : Specify the position of time display on the screen.
To Setup Special •• Weekday overlay : Specify the use of date display date on the screen.
1. Select <Special>. •• Size : Sets the size of OSD to small/medium/large.
2. Select each item and set it properly. •• Color : Sets the color of the OSD to white/red/blue/green/black/gray.
•• DIS : Compensates the image automatically when it is seen •• Transparency : Sets the transparency of OSD to opaque / low / middle / high.
to shake for stable image output.
MM `` Mitigate the degree of image vibration when the camera JJ `` Aitem.

position-adjustable item (Camera title, Date & Time) may not be displayed normally if it overlaps with another fixed OSD
vibrates due to the external factors such as wind.

`` Multilingual other than English: Input only in the selected language is available.
•• Sharpness : Adjust the overall sharpness of the image.
If selecting <On>, you can adjust the sharpness of the
image. To set the heater
•• Sharpness level : The higher the level is, the sharper and clearer the outline of the image becomes. 1. Select <Heater>.
•• Gamma : Adjust the contrast of the image. When frost forms, the user can click the button and turn on
•• Contrast : Adjusts the difference between the darkest area and the brightest area in the video. the heater for 30 minutes to remove the frost.
•• Color level : Adjust the strength of video color.
•• Defog : Compensate the video in the foggy or cloudy weather.
It is set to <Off> as a default. Specials are used when the video looks blurry in the foggy weather.
JJ `` Aton;lowat atemperature when frost is likely to form, the heater is always
high temperature where the product can be affected by it, it does not operate, even when the request to operate has
been sent.
-- Off : Disable the fog elimination function.
-- Auto : The image is automatically compensated according to the foggy level. Adjust <Defog level>
to be more effective. To Set IR
-- Manual : The user manually sets the amount of compensation for each image. 1. Select <IR>.
`` If the defog mode is set to <Auto>, the performance is proportional to the fog level. To keep the set defog level without
JJ regard to the fog level, set the defog mode to <Manual>. •• Mode : When the IR indicator turns on in B/W mode, the
screen will be protected from saturation on the center area
`` If the manual defog level is high in a thin fog, the image may become too dark. so that you can identify a short-distant object.
•• Defog level : Control the defog level. -- Off : IR mode will be disabled.
•• LDC : To determine whether or not to use the image distortion correction. -- Auto1 : Adjust the IR brightness according to the brightness of the object on the center screen.
•• LDC Level : To adjust the level of the distortion correction factor. -- Auto2 : The brightness of the IR is automatically adjusted according to the brightness of the object
located in the middle or periphery of the screen.
-- Manual : Adjust the IR brightness manually.
•• Level : Adjust the level of IR in manual mode.
46_ setup screen

Smart codec WiseStream
Set a desired area of the video incoming from the camera as ROI area and specify the detection sensitivity for This is the feature that optimizes the size of the video data by reducing the bit rate through increasing the
the area. compression of the parts where there is no movement after detecting the complexity in the image.
1. From the Setup menu, select the <Video & Audio ( )> 1. From the Setup menu, select the <Video & Audio ( )>
tab. tab.
●● setup screen
2. Click <Smart codec>. 2. Click <WiseStream>.
3. Set the image quality. 3. Select wise stream mode.
The ROI area will be displayed in the specified quality. -- Off : Wise Stream function will be disabled.
4. Specify an area of interest to monitor manually. -- Low ~ High : use the wise stream to select the bit rate
5. Select a desired area with the mouse pointer, and drag it as reduction level.
much as you want. 4. When done, click [Apply].
`` You can specify up to 5 distinct areas.
6. To cancel all the settings for the area, click the [Clear] button. JJ `` In the following cases, the WiseStream function may malfunction.
7. When done, click [Apply]. -- Sudden screen switch may cause distortion of the video.
-- It is not appropriate to use in an environment with too much movement and motion on the screen.
JJ `` The Smart codec will not be active if it is set to <Off> in <Video profile>. (page 37)
Focus setup
You can adjust the focus and zoom ratio of video image.
1. From the Setup menu, select the <Video & Audio ( )>
tab.
2. Click <Focus setup>.
3. Set the focus according to the following procedures.
1) Reset : Click the [Reset] button to return focus to the
default flange back position.
2) Focus (lens adjustment) : Adjusts the lens focus (Far  Near) and sharpens the image.
3) Zoom (lens adjustment) : Manually adjusts the magnifications (Wide  Tele).
4) Simple focus : Drags the mouse on the screen to designate a position on which to set the auto focus.
Press the [ ] button to automatically focus the video.
JJ `` The Simple focus mode may not fit correctly in the following cases:
-- Sudden change to the object in Simple focus mode (sudden movement, appearance or disappearance)
-- Radical change to the brightness in Simple focus mode
-- Image of a low contrast
-- If the camera is exposed to a strong light source in the front or surroundings
`` In case the focus is inappropriate apart from mentioned above, use [ , , , , , ] button to
manually adjust the focus.
`` In a situation where Simple focus is hardly applied, try to use the manual focus mode.
English _47
setup screen
Network Setup Registering with DDNS
To register your product with the Wisenet DDNS
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a 1. Visit the Wisenet DDNS web site (http://ddns.hanwha-
general Host Name so that the user can easily remember it. security.com) and sign in with a registered account.
JJ `` You can use the DDNS service only if the internet is connected.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <DDNS>.
3. Select the <DDNS> connection type.
4. Type in the DDNS items according to the selected type.
2. From the top menu bar, select <MY DDNS>.
•• Wisenet DDNS : Select this if you use the DDNS server
provided by Hanwha Techwin.
-- Product ID : Enter the product ID that is registered with
the Wisenet DDNS service.
3. Click the [Register Product] tab.
-- Quick connect : It sets port forwarding automatically when used with a UPnP (Universal Plug and 4. Enter the product ID.
Play) supporting router.
MM `` Ifgoyouto thewanthubto menu

use the DDNS service without using a hub that supports the UPnP function, click Quick connect, then
and activate port forwarding for your hub.
For more on how to set port forwarding for your hub, refer to “Port Range Forward (Port Mapping) Setup”. (page
28)
•• Public DDNS : Select one of provided public DDNS servers when you use a public DDNS server.
-- Service : Select desired public DDNS service server.
5. Select a <Type> and specify the <Model>.
-- Host name : Enter the name of the host that is registered with the DDNS server.
6. Specify the product location with a description if necessary.
-- User name : Enter the user name for the DDNS service.
7. Click [Product Registration].
-- Password : Enter the password for the DDNS service. The product will be added to the product list that you can
check.
JJ `` If selected <Quick connect>, be sure to select Wisenet DDNS service.
48_ setup screen

selected <Allow registered IP> for IP Filtering and <IPv6 setup> of <IP & Port> is set to <Use>, both IPv4 and IPv6
To connect to the Wisenet DDNS in camera setup
MM `` Ifaddresses of the computer currently configuring should be assigned.
1. From the DDNS setup page, set <DDNS> to <Wisenet
DDNS>. `` The IP address of the computer used for the current setup cannot be added to <Deny registered IP>, it should be added to
<Allow registered IP>.
2. Provide the <Product ID> that you registered product ID with
the DDNS site. `` Only the IP addresses that are set to <Use> will be displayed in the filter column.
●● setup screen
3. Click [Apply].
6. Select an IP to delete from the list.
When the connection is successfully made, you will see the
Click the [Delete] button.
message of <(Success)> on the screen.
Configuring public DDNS in Camera Settings HTTPS

1. Open the DDNS settings page and select <Public DDNS> for <DDNS>. You can select a secure connection system or install the public certificate for this purpose.
2. Enter the corresponding site’s host name, user name and password. 1. From the Setup menu, select the <Network ( )> tab.
3. Click [Apply] button. 2. Click <HTTPS>.
If the connection properly establishes, <(Success)> appears. 3. Select a secure connection system.
4. When done, click [Apply]. `` To access the camera using HTTPS mode, you have to type the IP
address for the camera in the form of “https://<Camera_IP>”.
MM `` ToForuseportDDNS service properly, both DDNS setup and the router’s port forwarding setup are required.
forwarding setup, refer to “Port Range Forward (Port Mapping) Setup”. (page 28)
If you failed to configure the Web viewer settings in HTTPS mode with
Internet Explorer, edit the Internet options as follows: <Menu  Tools 
Internet Options  Advanced  Security  Uncheck TLS 1.0, and check
TLS 1.1, TLS 1.2>
IP filtering 4. Search for the public certificate that you want to install on the camera.
You can create a list of IPs that you want to grant or deny access to them. To install the certificate on the camera, you need to provide a certificate name (it can be arbitrarily assigned
by the user), certificate file issued from the certification authority and a key file.
1. From the Setup menu, select the <Network ( )> tab. `` The <HTTPS (Secure connection mode using the public certificate)> item will be active only if there exists a public certificate
2. Click <IP filtering>. installed.
3. Select <Filtering type>. 5. When done, click [Apply].
•• Deny registered IP : If selecting this, access from those IPs
that are added to the filtering will be restricted.
Installing the certificate
•• Allow registered IP : If selecting this, access from only
those IPs that are added to the filtering will be accepted. 1. Enter the certificate name.
4. Click the [Add] button. 2. Click the [Browse ( )] button, select the public certificate file and key file to be installed, and then click
The IP list will be created. the [Install] button.
5. Provide the IP that you want to grant or deny access from.
When you enter an IP address and a Prefix, the list of IP addresses available will appear in the right-side Deleting the certificate
filter range column.
1. Click [Delete] button.
2. To delete a public certificate, you should access the network video decoder in the mode of <HTTP (Do
not use secure connection)> or <HTTPS (Secure connection mode using a unique certificate)>.
English _49
setup screen
802.1x QoS
When connecting network, you can choose whether using 802.1x protocol, and then install the certification. You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the <Network ( )> tab. 1. From the Setup menu, select the <Network ( )> tab.
2. Click <802.1x>. 2. Click <QoS>.
3. Set the <IEEE 802.1x setting>. 3. Click the [Add] button.
•• IEEE 802.1x : Specify the use of the 802.1x protocol. The IP list will be created.
•• EAP type : Select EAP-TLS or LEAP. 4. Enter an IP address to which you will apply QoS.
•• EAPOL version : Select version 1 or 2.
•• ID : Enter the client certificate ID in EAP-TLS and the user ID in LEAP.
•• Password : Enter the client private key password in EAP-TLS and the user password in LEAP. You do
MM `` The default prefix for IPv4 is 32;
For DSCP, the default is set to 63.
not have to enter the password in EAP-TLS if it uses a key file that is not encrypted. `` Only the IP addresses that are set to <Use> can be prioritized.
5. Select an IP to delete from the list.
JJ `` If the connected network device does not support the 802.1x protocol, the protocol will not operate properly even if you set it. Click the [Delete] button.
`` LEAP is an authentication method with poor security. Use it only in an environment where EAP-TLS is not available.
4. Install/remove the certificate.
The certificate is needed only for EAP-TLS.
SNMP
•• CA certificates : Select a public certificate that contains the public key.
•• Client certificate : Select a public certificate that contains the client certificate key. With the SNMP protocols, the system or network admin can monitor the network devices on a remote site,
and configure the environment settings.
•• Client private Key : Select a public certificate that contains the client private key.
5. When done, click [Apply]. 1. From the Setup menu, select the <Network ( )> tab.
2. Click <SNMP>.
To install/remove 802.1x related certificates 3. Specify the <SNMP>.
•• Enable SNMP v1 : SNMP version 1 will be active.
1. Press the [Browse ( )] button for each item and select a certificate to install.
•• Enable SNMP v2c : SNMP version 2 will be active.
2. If no certificate is installed, you will see “Not Available” appearing next to the selected item. -- Read community : Provide the name of the read
3. Press the [Install] button to start installation with a message of “Installed” next to the item. community where you can access to the SNMP
4. Press the [Delete] button to remove the certificate. information.
The default name is <public>.
-- Write community : Provide the name of the write community where you can access to the SNMP
information. The default name is <write>.
•• Enable SNMP v3 : SNMP version 3 will be active.
-- Password : Specify the default password for SNMP version 3.
`` The default password can be exposed to a hacking thread so it is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
`` Password should be longer than 8 characters, no more than 16 characters.
50_ setup screen

•• Enable SNMP Trap : SNMP trap is used to send important events and conditions to the Admin. Event Setup
-- Community : Enter the trap community name to receive messages.
-- IP address : Enter the IP address to which messages will be sent. Event setup
-- Authentication failure notification : It specifies whether an event shall be generated when the You can easily set the event detection items, and move to the detailed setting.
community information is invalid.
1. From the Setup menu, select the <Event ( )> tab.
●● setup screen
-- Network connection notification : It specifies whether an event shall be generated when the network
disconnection is restored. 2. Click <Event setup>.
4. When done, click [Apply]. 3. Activate desired items on the Event list.
`` SNMP v3 is only able to be set when the secure connection mode is HTTPS.
JJ Refer to “HTTPS”. (page 49)
MM `` Toredirected
configure detailed event settings, click a desired type. You will be
to the detailed settings.
`` If you don’t use SNMP v3, there may be a security issue.
Auto IP configure
You can set the IP available for access and camera searching automatically. FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to
1. From the Setup menu, select the <Network ( )> tab.
your PC if an event occurs.
2. Click <Auto IP configure>.
3. Set the <Link-Local IPv4 address>.
An additional IP address may be assigned to assess the 2. Click <FTP / E-mail>.
camera from the Link-Local network. 3. Select <FTP configuration> or <E-mail configuration> and
•• Auto configure : It specifies Able or Disable for the Link- enter / select a desired value.
Local IPv4 address. •• FTP configuration
•• IP address : Display the assigned IP address. -- Server address : Enter the IP address of the FTP server
•• Subnet mask : Display the subnet mask of the assigned IP. that you transfer the alarm or event images to.
4. Set the <UPnP discovery>. -- ID : Enter the user ID with which you will log in to the
Cameras can be automatically searched in the client and operating system in support of the UPnP FTP server.
protocol.
•• UPnP discovery : It specifies Able or Disable for UPnP Discovery. -- Password : Enter the user account password for logging
into the FTP server.
•• Friendly name : Display the camera name.
Friendly name is displayed in the format of WISENET-<Model Name>-<MAC Address>. -- Upload directory : Specify the FTP path where you will transfer the alarm or event images.
-- Port : The default port of the FTP server is 21; however, you can use a different port number
MM `` In the Windows operating system which basically supports UPnP, the cameras connected to the network are displayed. according to the FTP server settings.
5. Set the <Bonjour>. -- Passive mode : Select <On> if you need to connect in passive mode due to the firewall or the FTP
Cameras can be automatically searched in the client and operating system in support of the Bonjour server settings.
protocol.
•• Bonjour : It specifies Able or Disable for Bonjour.
•• Friendly name : Display the camera name.
Friendly name is displayed in the format of WISENET-<Model Name>-<MAC Address>.
MM `` InBonjour
the Mac operating system, which support Bonjour by default, the connected cameras are automatically displayed in the
bookmark of the Safari web browser.
If the Bonjour bookmark is not displayed, check Bookmarks Setup in the “Preference” menu.
English _51
setup screen
•• E-mail configuration To make recording on the Micro SD memory
-- Server address : Enter the SMTP address of the email server that you transfer the alarm or event
1. Set the SD card unit to <On>.
images to.
2. Click the [Apply] button.
-- Authentication : Select whether to use authorization.
3. Check the memory card’s <Free size> and <Total size>.
-- TLS : Specify the use of TLS. You can format the Micro SD card by clicking the <Format> button.
-- ID : Enter the user ID for logging into the email server. `` Some frames may be skipped if the Micro SD memory card operates at the lower speed than recommended.
For more details, refer to “Recommended Micro SD/SDHC/SDXC Memory Card Specifications”. (Page 6)
-- Password : Enter the user account password for logging into the email server.
`` For a Micro SD memory card with a large capacity, the formatting will be slowed down accordingly.
-- Port : The default port of the email server is 25; however, you can use a different port number
`` The data traffic will increase when the camera is set to higher resolution, higher bit rate, and/or higher framerate.
according to the email server settings. If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
-- Recipient : Enter the address of the email recipient. `` When a frame skip occurs, images are saved at the rate of min. one image per sec.
-- Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the 4. Specify the storage action.
sender may be classified as SPAM by the email server and thus may not be sent. •• Record profile : The name of profile to be recorded is displayed.
-- Subject : Enter a subject for your email. •• Normal recording : Make recording at a certain frame rate.
-- Body : Provide the text for the massage. Attach the alarm or event images to the email that you are •• Event recording : Set the recording type for a certain event that occurs.
preparing. •• Pre event duration : Specify the time point before the occurrence of the alarm; starting from the time
point, the images will be transferred. You can specify up to 5 seconds before the occurrence of the
4. When done, click [Apply]. alarm.
•• Post event duration : Specify the time point after the occurrence of the alarm; to the specified time
point, the images will be transferred. You can specify up to 120 seconds after the occurrence of the
Storage
alarm.
You can activate recording on your device, set the recording conditions, check the saved data capacity and •• Record file type : It specifies the file format of the recorded images.
format the device itself.
-- STW : It is Hanwha Techwin’s unique file format.
1. From the Setup menu, select the <Event ( )> tab. -- AVI : It is the conventional avi format.
2. Click <Storage>.
3. Select a device to save data in. JJ `` If the Record file type is changed, the existing data is formatted.
•• Overwrite : If the Micro SD memory is full, this will delete old data and store new data in replacement.
MM `` If your device is properly recording data, it will display “Recording”. •• Auto delete : Data for a certain period is deleted, while other data is not deleted.
`` If you see an “Error” message, check the following: This can be set within the range of one day to 180 days.
-- Check the storage to see if it is connected to the device.
-- Check the files in the storage to see if they are damaged.
JJ `` Ifrecovered.
the storage period is expired, data is automatically deleted and new data will be recorded. Once deleted, it cannot be
-- Check the storage to see if they are physically damaged.

5. Set <SD File System>.
`` If the “Error” message does not disappear after following the instructions, format the Micro SD card.
•• Type : Camera supports VFAT and ext4 as an SD card file system, which can be configured by the user.
After formatting, if the error message still remains, replace the Micro SD card.
(However, in case of ext4 file system, an additional application is required to recognize the Windows
`` If you remove the Micro SD card without changing a button to ‘off’ position in settings or if you connect a camera to an operating system)
unstable power source, the Micro SD card may be damaged.
JJ `` If the settings are changed, the existing data will be formatted.
`` The number of simultaneously accessible new profiles after the recording mode is activated is 2. `` It may take up to 10 minutes to format an SD card in the ext4 file system.
JJ
6. Specify the <Normal record schedule>.
•• Always : Always save recorded video in the Micro SD memory card.
`` If set to Always, the activation time cannot be changed.
•• Only scheduled time : Records only on the specified time of the specified day of week.
52_ setup screen

If you want to record in your NAS NAS (Network Attached Storage) guide
1. Set the saving operation and basic recording.
JJ `` Auto deletion is supported only if your NAS meets the recommended JJ `` Since data may not be saved after a temporary network interruption when using NAS, it is recommended that you use SD at
the same time to prevent loss of recorded images.
specifications.
`` If the setting allows a Micro SD memory card and the NAS to be simultaneously connected for use, the higher priority for
●● setup screen
2. Enter the information registered in your NAS. recording goes to the NAS.
•• IP address : Unique IP address assigned to the NAS. `` If you activate Overwrite to the NAS by setting it to <Off> and the available capacity is below 1%, it will be saved in the Micro
•• ID : An ID registered in the NAS. SD card.
•• Password : Password registered in the NAS. `` If you are saving data in the NAS, you might be unable to save it when you insert a Micro SD memory card used by another
•• Default folder : Designate the NAS user folder to save data camera.
in.
`` NAS recommended specs : Refer to “NAS recommended specs”. (Page 6)
3. Click the [Test] button to see if you can successfully connect to the NAS.
`` If you change the NAS saving while saving data in the NAS, it will not be reflected in the system immediately.
`` If you remove NAS equipment on your own while saving data, or if the network is disconnected, NAS saving operation will be
JJ `` If the success message is displayed, it means that you can successfully save data in the NAS. terminated abnormally.
`` If the fail message is displayed, check the following.
`` NAS saving allows only one camera to a folder. Logging in with another camera is not allowed, and the images will not be
-- Confirm that the IP address of the NAS is valid.
saved.
-- Confirm that the ID/password of the NAS is valid.
-- Confirm that you can access the folder designated as the default folder using the ID of the NAS. The following is a description of how to save data using the NAS according to the Synology NAS method,
which is one of the recommended products.
-- Confirm that the NAS SMB/CIFS items are unchecked.
-- Confirm that the NAS IP address and the camera IP address are in the same format. 1. Access the Synology NAS as an admin.
ex) The NAS & camera subnet mask initial value is 255.255.255.0. In this example, the NAS IP Address is set to
If the IP address is 192.168.20.32 then the NAS IP address should be in the range of 192.168.20.1~192.168.20.255. [192.168.20.253].
-- Check whether you tried to access as another user without formatting the default folder saved or used.
-- Confirm that you used recommended NAS equipment.
4. After the settings are completed, set the NAS unit to <On>.
6. Log in the NAS and check the <Free size> and <Total size>.
You can format the default folder specified in the NAS connection setting by clicking the <Format> button. 2. If you access it as an admin, the following screen will be
`` Since data may not be saved after a temporary network interruption when using NAS, it is recommended that you use SD at the displayed. Click the [Control Panel].
same time to prevent loss of recorded images.
`` The data traffic will increase when the camera is set to higher resolution, higher bit rate, and/or higher framerate.
If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
`` When a frame skip occurs, images are saved at the rate of min. one image per sec.
3. Click the <Shared Folder> in the file sharing and privilege

menu.
English _53
setup screen
4. Click the [Create] button. 10. Basic setting in the NAS is completed.
5. After entering the shared folder name(ID), click the [OK] Connect your camera to the actual NAS.
button to create a shared folder. As shown below, enter the NAS connection setting items.
In this example, the shared folder name is [testDirectory].
11. After entering item 10, check <On>.

Finish saving by using the NAS.
6. In Windows, for NAS access, set the privilege for the shared
folder as follows. Alarm output
Check the admin’s [Read/Write].
2. Click <Alarm output>.
7. Click on the <User> in the file sharing and privilege menu. 3. Configure the camera alarm output settings.
`` If you change the alarm output type, the alarm out button on the
monitoring page and alarm output type displayed on Event Setup page
will be changed accordingly.
•• Type
-- N.O. (Normal Open) : Considers “Open circuit” status
of the sensor or alarm input device as normal, and triggers alarm event if becomes “Closed circuit”
status.
-- N.C. (Normal Close) : Considers “Closed circuit” status of the sensor or alarm input device as normal,
8. After clicking the [Create] button, enter name(ID) and and triggers alarm event if becomes “Open circuit” status.
password.
•• Mode : Sets the alarm output method.
In this example, name(ID) is set to [testID] and password is
also set to [testID]. `` There is difference between operations when clicked alarm output button while disabled.
-- Pulse : It is activated during the time period specified by the duration (switching interval) and then
becomes inactive automatically.
-- Active/Inactive : It maintains as activated until the user clicks the button again to make it inactive.
•• Duration : Set the alarm duration that maintains activated if the mode is set to pulse, from 1 to 15
9. In Windows, set the privilege for NAS access. seconds.
For the shared folder created in step 4 called “testDirectory” 4. When done, click [Apply].
check [Read/Write].
54_ setup screen

Alarm input Time schedule
You can set the alarm input type, activation time, and operation mode. You can configure settings to transmit images at regular intervals at a scheduled operation time regardless of
the occurrence of an event.
2. Click <Alarm input>. 1. From the Setup menu, select the <Event ( )> tab.
3. Set whether or not to <Enable>. 2. Click <Time schedule>.
●● setup screen
4. Select the type. 3. Set whether or not to <Enable>.
•• N.O. (Normal Open) : It is normally open, but if it is closed, 4. Specify the <Transfer interval>.
an alarm will be triggered. 5. Specify the <Event activation time>.
•• N.C. (Normal Close) : It is normally closed, but if it is open, •• Always : Always activates in operated mode at the set
an alarm will be triggered. interval.
5. Specify the <Event activation time>. •• Only scheduled time : Periodically activates in operated mode at a specified time and date.
•• Always : Always check if an alarm occurs. It activates in
operated mode when the alarm occurs. JJ `` The transfer interval setting value must be smaller than the preset activation interval to succeed in image transmission.
`` If set to <Always>, the activation time cannot be changed. 6. Specify the activation conditions.
•• Only scheduled time : Check if an alarm occurs at a specified day of the week for a specified time •• FTP : Specify the use of the FTP transfer if an event occurs.
period. It activates in operated mode when the alarm occurs.
`` Refer to “FTP / E-mail” for more details. (page 51)
-- [ ] : Sets the time display format on the vertical axis.
-- [Reset] : Reset all settings.
6. Specify an operation that will perform if an alarm occurs.
•• FTP : Specify the use of FTP transfer in the alarm input setup.
•• E-mail : Specify the use of email transfer in the alarm input setup.
•• Record : You can set up the alarm to record to a Micro SD card or an NAS when operating.
`` Set <Device> to <On> in <Storage>. (page 52)
•• Alarm output1 : Select whether to set the alarm output if an alarm is incoming, and specify the alarm
output time.
English _55
setup screen
Network disconnection Configure analysis settings
When the network is physically disconnected, it is considered as an event to be saved.

Motion detection
You can configure settings to generate an event signal when a motion is detected.
2. Click <Network disconnection>.
3. Set whether or not to <Enable>. 1. From the Setup menu, select the <Analytics ( )> tab.
4. Configure the event motion schedule and event motion 2. Click <Motion detection>.
conditions. 3. Set whether or not to <Enable Motion detection>.
`` For more information about <Event activation time> and <Event 4. Set an <Area> and <Exclude area>.
action settings>, refer to “Alarm input”. (page 55) You can set up to 8 areas.
5. When done, click [Apply]. You can specify level and sensitivity settings separately for
each area.
A single area supports a shape with up to 8 vertexes.
Select 4 vertexes on the video using the mouse to create a
rectangle, and select each line of the rectangle and add up to
App event 4 more points to create a desired shape.
You can set the system to generate signals for the events defined on the application. The event signals 5. Configure settings for each item.
provided vary depending on the application function. •• Level of detection : If the motion is greater than the level configured, a motion detection event is
generated.
Even on the chart, if the motion is greater than the boundary of the level configured, the color is
2. Click <App event>. displayed differently.
3. Set whether or not to <Enable>. •• Sensitivity : Sets the sensitivity of motion detection for each area. Decrease the sensitivity in an
4. Configure the event motion schedule and event motion environment where the background and the object are clearly distinguished, and increase the sensitivity
conditions. in a dark environment where the background and the object cannot be clearly distinguished.
`` For more information about <Event activation time> and <Event •• Hand over : To use Handover, select <Enable>. You can relocate a specific camera to a specific PTZ
action settings>, refer to “Alarm input”. (page 55) preset position when a motion is detected in a configured detection area. Specifies a camera for each
detection area.
5. When done, click [Apply]. •• Receiver camera : The receiving camera can be inter-operated with the detection area.
6. Configure the event motion schedule and event motion conditions.
`` For more information about <Event activation time> and <Event action settings>, refer to “Alarm input”. (page 55)
JJ `` Detected size of an object may have difference with the actual size according to its shape.
`` In the following cases, motion detection performance may be impaired or a malfunction may occur.
-- The object color or brightness is similar to the background.
-- Small activities around the border area of the camera’s field of view.
-- Multiple movements continue occurring at random due to a scene change, rapid lighting changes or other reasons.
-- A fixed object continues moving in the same position.
-- Motions of less position changing such as approaching to the camera or fading away from the camera.
-- Moving object approaches to the camera too close
-- An object hides other objects behind.
-- Too fast object (for a proper detection, one object should be found overlapping between contiguous frames).
-- Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp.
-- In severe snow, rain, wind or in dawn / dusk.
56_ setup screen

Tampering detection Defocus detection
You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing You can configure settings to generate an alarm signal when a defocus of the camera lens is detected.
direction, blocked lens and other overall change of scenes from the video.
1. From the Setup menu, select the <Analytics ( )> tab.
1. From the Setup menu, select the <Analytics ( )> tab. 2. Click <Defocus detection>.
2. Click <Tampering detection>. 3. Set whether or not to <Enable Defocus detection>.
●● setup screen
3. Set whether or not to <Enable Tampering detection>. 4. Configure settings for each item.
4. The chart represents the degree of tempering. Set the level •• Level of detection : An alarm is generated if the current
sensitivity of tempering to detect (range: 1 to 100). level is higher than the detection level configured.
5. Set the sensitivity. •• Sensitivity : The higher the intensity is, the higher the level
The higher the set value, the more sensitive the camera of the chart that is output for the same video.
reaction (range: 1 to 100). •• Minimum duration (s) : An alarm is generated if the level state higher than the detection level remains
6. Specify the minimum monitoring duration. continuously for the minimum monitoring duration configured.
An event signal is generated if a state higher than the detection level remains for the minimum monitoring 5. Configure the event motion schedule and event motion conditions.
duration (unit: seconds)
7. Specify whether to exclude dark areas.
This function makes it difficult to distinguish darkness due to de-illumination from darkness due to being
blocked by an object. Despite this property, if you want to exclude an alarm for sudden changes in screen
brightness such as de-illumination, you should enable this function. JJ `` After an alarm for defocus detection is generated, if you want to receive an alarm for defocus detection again, you need to
return to a stable state at least once. Examples of returning to a stable state are as follows.
`` For more information about <Event activation time> and <Event action settings>, refer to “Alarm input”. (page 55) -- Use Defocus Detection check box is deselected
-- Video identification is available, as simple focus is activated
-- If an object in the video moves to a position at which good focus is ensured and thus an identifiable tempering is detected
`` In the following cases, the defocus detection performance may be impaired or a malfunction may occur.
JJ `` The detection will be restarted after stabilization for a certain period of time (about 5 seconds). During stabilization, detection
is not available.
`` If false alarms are frequently generated, you should gradually decrease the sensitivity to minimize false alarms. -- Sudden changes in the illumination (e.g. indoor light shutting off)
`` If you use a low sensitivity, alarms may be generated even by very small changes on the screen, but false detection may -- Lens blocked by a large object that covers almost all of the screen
occur in response to changes in moving objects or brightness. -- Changes the focus object by changing the camera position.
`` In the following cases, the tempering detection function may malfunction.
-- Monitoring environment with simple background, night and low light level environment.
-- Severe camera vibration or sudden lighting changes
English _57
setup screen
Fog detection Face detection
You can configure settings to generate an event signal when fog is detected. You can configure the settings to generate an event signal in response to the detection of a face in the
specified area.
2. Click <Fog detection>. 1. From the Setup menu, select the <Analytics ( )> tab.
3. Set whether or not to <Enable Fog detection>. 2. Click <Face detection>.
4. Configure settings for each item. 3. Set whether or not to <Enable Face detection>.
•• Level of detection : An alarm is generated if the current 4. Set an <Area> and <Exclude area>.
level is higher than the detection level configured. 5. Set the sensitivity level.
•• Sensitivity : The higher the intensity is, the higher the level `` The higher the sensitivity, the more detailed and precise face detection is
of the chart that is output for the same video. available.
•• Minimum duration (s) : An alarm is generated if the
6. Configure the event motion schedule and event motion
level state higher than the detection level remains continuously for the minimum monitoring duration
conditions.
configured.
`` Defog : Specifies whether to use the fog removal function when fog is detected.
6. When done, click [Apply]. IVA (Intelligent Video Analysis)
You can configure settings to generate an event signal when a motion or situation meeting the specified
`` After an alarm for the fog detection is generated, if you want to receive an alarm for fog detection again, you will need to event rules is detected.
JJ return to a stable state at least once. Video improvement after fog removal is not recognized as a stable state. Examples of
returning to a stable state are as follows.
2. Click <IVA>.
-- Use Fog Detection check box is deselected.
3. Set whether or not to <Enable IVA>.
-- Video is identifiable as fog or smoke disappears.
4. Configure rules to detect. For more information about
`` In the following cases, fog detection performance may be impaired or a malfunction may occur. settings, refer to “Configure analysis rules”.
-- Monotonous monitoring environment, night or low illumination environment Configurable rules are as follows.
-- Sudden changes in the illumination (e.g. indoor light shutting off) -- Crossing : You can detect an object passing in the
selected direction on a specified virtual line.
-- Lens blocked by a large object that covers almost all of the screen
-- Changes the focus object by changing the camera position. -- Intrusion : You can detect the emergence of a moving
object within a virtual area.
-- Enter : Detects an object entering from the outside to the inside of the virtual area.
-- Exit : Detects an object exiting from the inside to the outside of the virtual area.
-- Appear(Disappear) : Detects a new object appearing inside a virtual area, which is monitored for a
specified period of time after its position is fixed, or detects a fixed object that disappears and is not
monitored for the monitoring duration.
-- Loitering : Detects an object wandering inside the virtual area for longer than the monitoring duration.
5. Select area(s) that you don’t want to include in the analysis, and excluded area(s).
6. Set the sensitivity level and a size of interest (if necessary).
For more information about settings, refer to “Common Settings”.
58_ setup screen

Configure analysis rules Audio detection
You can configure individual analysis rules as follows. You can set to detect sound over the specified level and trigger an event accordingly.
•• Crossing 1. From the Setup menu, select the <Analytics ( )> tab.
1. Select the <Virtual line> tab. 2. Click <Audio detection>.
2. Left-click on the screen to specify the start and end of the line at a desired position to detect. 3. Set whether or not to <Enable Audio detection>.
●● setup screen
3. Select a direction of interest. 4. Set the audio detection’s sound level.
4. When done, click [Apply]. The lower the level, the smaller the sound change is detected.
5. To remove the rules that have been configured, right-click on the line and click the [OK] button in the pop-
up window that appears.
MM `` The audio detection level is designed to normalize the input data to a
value between 1 and 100 and detect the signal larger than threshold
level. It is unrelated to the decibel (dB) level.
•• Intrusion, Enter, Exit, Appear(Disappear), Loitering
1. Click on the <Virtual area> tab.
2. Left click on the screen to specify 4 vertexes at desired positions.
3. From the virtual area that has been configured, select an analysis category.
4. When done, click [Apply]. <Video & Audio> - <Audio setup> and set the proper volume for your MIC as an audio input source, so that the
5. To remove the rules that have been configured, right-click on the line and click the [OK] button on the pop-
MM `` Select
audio detection function can work properly.
up window that appears. `` If detected audio level is too low, set the audio input gain to a higher level in <Audio setup>.
`` You can use the audio detection function when the camera is connected with an audio input device.
Common settings
Common settings are settings to increase the detection accuracy and minimize false positives, based on the Sound classification
use environment.
You can configure settings to generate an event signal in response to the detection of a specified sound
•• Sensitivity source.
1. Select the <Common> tab. 1. From the Setup menu, select the <Analytics ( )> tab.
`` You can change the sensitivity of distinguishing the screen background from motions.
2. Click <Sound classification>.
In a situation in which objects can be clearly distinguished from backgrounds, set this to a low sensitivity level. For the opposite
scenario, in which it is hard to distinguish objects, such as in a low illumination situation, set this to a high level. 3. Set whether or not to <Enable Sound classification>.
2. When done, click [Apply]. 4. Set the level of audio energy for the sound source to
classify. The energy level value for the input audio is updated
•• Size periodically from right to left, and is drawn on the area. Sound
1. Select the <Common> tab. source classification is only applied to audio at a level higher
than the specified value.
2. For each rectangle that represents the minimum size and the maximum size, right-click on the vertex at
the bottom-right to move and resize it. 5. Configure settings for each item.
`` Motions smaller than the specified minimum size or bigger than the maximum size are not detected. To avoid unintended •• Noise reduction : Specify the <Enable> status.
detections caused by great and small noises, set minimum/maximum motion sizes appropriately in accordance with your `` If the noise in the surrounding environment is too loud, exceeding 55 to 60dB, use the noise reduction function.
environment. Note that the same motions on the same location can be detected differently in terms of their detection size; it is If the noise reduction function is used, the sound classification function may be degraded or may malfunction depending on
recommended to consider and include the tolerable difference when setting the minimum/maximum detection sizes. the environment, as the original sound source is reduced. If you use the noise reduction filter in a quiet environment, the sound
source classification function may be impaired.
•• Categories : Select a sound source to classify.
`` Sound source definition
-- Scream : Loud sound generated by humans, such as a scream or shout by a male/female adult or children
-- Gunshot : Gunshot sound (excluding rapidly-generated, consecutive gunshot sounds)
-- Explosion : Sound of sudden explosion that is the result of a destructive action
-- Crashing glass : Sound of glass breakage
English _59
setup screen
6. Configure the event motion schedule and event motion conditions. System Setup
7. When done, click [Apply]. Product information
1. From the Setup menu, select the <System ( )> tab.
JJ `` In <Video & Audio> - <Audio setup>, it is recommended to set the audio input gain to a value ranging from 4 to 6. 2. Click <Product information>.
`` In <Video & Audio> - <Audio setup>, if you set the audio input source to an external microphone, the recommended
microphone specifications are as follows. 3. Check the camera information, or provide details according
to your network environment.
-- Frequency range: 40 to 16,000Hz •• Model : Model name of the product.
-- Impedance: 1,500Ω •• Serial number : Product serial number.
-- Sensitivity: -40±3 dB (7.1~14.1 mV) •• Device name : Provide a device name that will be displayed
`` In the following cases, sound source classification performance may be impaired or malfunction. on the Live screen.
•• Location : Specify the location where the camera is installed.
-- Gunshot sounds are generated consecutively, such as the sound made by a machine gun rather than a one-shot sound.
•• Description : Provide detailed information about the camera location.
-- Noise is too loud to distinguish from the target sound source.
•• Memo : Provide an explanation about the camera for better understanding.
-- 2 or more sound sources are input simultaneously.
•• Language : Select a preferred language for the Web Viewer OSD.
-- Sound source classification is applied in a quiet environment using the noise removal function
-- Sound of applause or scream is heard from a close distance (within 1m) from the camera
-- A loud sound source that does not belong to any of the sound source categories such as aircraft sound or siren sound is MM `` The default language is set to <English>.
suddenly generated
-- The external microphone does not conform to the recommended specifications 4. When done, click [Apply].
Upgrade / Reboot
1. From the Setup menu, select the <System ( )> tab.
2. Click <Upgrade / Reboot>.
3. Select a desired item and set it appropriately.
•• Upgrade : Performs upgrading the system.
When reconnecting, the web viewer will not run normally if
the browser cache is not completely clear.
•• Factory default : Initializes all setting information including the camera settings to the factory reset state.
(however, logs are not initialized)
-- Select the <Except network parameter & Open Platform> check box and settings other than
network settings and open platform settings will be reset.
`` The IP addressing system will be defaulted to DHCP if you reset the camera. If no DHCP server is found, the previous settings
will be restored automatically.
•• Configuration backup & Restore : Backs up the current system settings before performing the
restoration process. The system is automatically restarts after backup or restoration.
•• Restart : Restarts the system.
60_ setup screen

To perform the upgrade Log
1. Click [Browse ( )] and specify a file to upgrade. You can check the system log or event log.
2. Click [Upgrade]. 1. From the Setup menu, select the <System ( )> tab.
3. An “Upgrade” progress bar is prompted to show the upgrading status. 2. Click <Log>.
4. Once completed upgrading, the browser exits and the camera restarts. 3. Select a log type.
●● setup screen
•• Access Log : You can check the log information that
MM `` ItIf may take a max of 10 minutes for the upgrade process.
you forcibly terminate the upgrade process, upgrade will not be completed properly.
contains the user’s access and the access time.
•• System log : You can check the system logs where
`` During restarting the system, accessing with web viewer will not be made. any system changes are recorded including the time
information.
`` You can download the latest version from the Hanwha Techwin web site. •• Event log : You can check the event logs including the time
information.
4. From the right log list, select an item to search for.
To back up the current settings
•• If you select <All> in the top left dropdown list, all logs for the applicable log type will be displayed.
1. Click [Backup]. 5. If one page can not display all the logs available, use the bottom buttons to move to the previous, next, or
2. A file in a “.bin” file format is saved in “Library” -> “Document” -> “ Downloads”. the last item.
6. Click on the <Backup> button to save all the log data for the currently selected mode in the “time stamp
value create by camera in modelname-mode-camera.txt file” in the download folder for the browser.
To restore the backup settings
1. To restore the backup settings, click [Restore]. MM `` Each page displays 15 logs with the latest one displayed at the top.
2. Select a desired backup file. `` Each log contains up to 1,000 records and after 1,000 records are saved, the oldest log is deleted when a new record is
generated.
`` If you perform the backup or restoration, the web browser will be closed and the camera will reboots.
MM
`` If you try to recover the config file backed up in other model, some functions may malfunction and you need to change the
setting manually.
English _61
setup screen
Open Platform Setup
Open Platform
A user can install an application on their camera to execute additional functions.
1. From the Setup menu, select the <Open Platform ( )>

tab.
2. Click <Open Platform>.
3. Click the [Browse ( )] button to select the *.cap file from
the user folder.
4. Click the [Install] button to install your application.
5. The information of the installed application is displayed in the list.
•• Uninstall : Deletes installed or operating applications.
•• Go App : You will be redirected to the app page of each application.
•• Start : Execute an installed application.
•• Stop : Terminates a running application.
•• Health : Displays the currently running application’s resource occupation rate, thread counts and
execution time, etc.
•• Priority : Sets the priority of running applications.
If the total resource utilization rate of the camera (including main tasks and applications) exceeds
80%, an ongoing application will be forced to stop. In this case, the priority set by the user is used to
determine which application should be stopped first.
•• Auto start : When the camera’s power supply or main task is running, a certain application for which
auto execution has been activated will run automatically.
•• Application manager : This displays the resource occupation rate of an application currently running in
your camera.
-- Memory Usage (%) : This is the memory utilization rate for each application.
-- CPU Usage (%) : This is the CPU utilization rate for each application.
-- Thread count : This is the number of threads created by each application.
-- Duration : This is the total execution time of each application.
-- Kill Task : Terminates an application.
-- Total Usage : This is the total resource occupation rate of the camera (including main tasks and
applications).
MM `` For questions about application use or installation, check the Techwin developer website.
62_ setup screen

appendix
Specification Description
Items XND-6080/XND-6080V/ XND-6080R/XND-6080RV/ XND-8080R/XND-8080RV/
Description
XNV-6080 XNV-6080R XNV-8080R
Items XND-6080/XND-6080V/ XND-6080R/XND-6080RV/ XND-8080R/XND-8080RV/
Backlight Compensation Off / BLC / HLC(Masking/Dimming) / WDR
XNV-6080 XNV-6080R XNV-8080R
Wide Dynamic Range
●● appendix
Imaging Device 1/2.8” 2M CMOS 1/1.8” 6M CMOS 150dB 120dB
Total Pixels 1945(H) x 1109(V) 2.16M 3096(H) x 2094(V) Contrast Enhancement SSDR (Off / On)
Effective Pixels 1945(H) x 1097(V) 2.13M 2616(H) x 1976(V) Digital Noise Reduction SSNR5 (2D+3D Noise Filter) (Off / On)
Scanning System Progressive Scan Digital Image Stabilization Off / On
Video Color : 0.015 lux(F1.4, Color : 0.015 lux(F1.4, Color : 0.07 lux(F1.3, Defog Auto(input from fog&Dust detection)/Manual/Off
Min. Illumination 1/30sec), B/W : 0.0015 1/30sec), B/W : 0 lux(IR 1/30sec), B/W : 0 lux(IR
lux(F1.4, 1/30sec) LED On) LED On) Motion Detection Off/ On(8ea, 8point Polygonal zones), Handover
S / N Ratio 50dB Off / On (32ea, polygonal zones)
Privacy Masking - Color : Gray, Green, Red, Blue, Black, White
CVBS : 1.0 Vp-p / 75Ω composite, 720x480(N), 720x576(P), for installation
Video Out - Mosaic
USB : Micro USB type B, 1280x720 for installation
Off / Low / Middle / High /
Focal Length (Zoom Ratio) 2.8~12mm(4.3x) motorized varifocal
3.9~9.4mm(2.4x) Gain Control Off / Low / Middle / High
motorized varifocal Manual
Max. Aperture Ratio 1.4(Wide) ~ 3.6(Tele) F1.3 White Balance ATW / AWC / Manual / Indoor / Outdoor (included Mercury & Sodium)
H: 92.1˚, V: 67.2˚, D: Contrast level adjustment

H: 119.5˚, V: 62.8˚, D: 142.1˚
Angular Field of View 119.9˚
H: 27.9˚, V: 15.7˚, D: 32.0˚ Operational LDC On/Off (5 levels with Min/Max)
H: 38.7˚, V: 29.0˚, D: 48.6˚
Lens
Min. Object Distance 0.5m (1.64ft) Electronic Shutter Speed Minimum / Maximum / Anti flicker (2 ~ 1/12,000sec)
Simple Focus (Motorized V/F) / Manual - Remote control via network (Manual, Digital PTZ 24X, Digital PTZ(Preset, Group)
Focus Control
Simple Focus)
Flip : On/Off
Lens Type DC Auto Iris, P-iris Flip / Mirror Mirror : On/Off
Mount Type Board-in type Hallway : 90°/270°
Pan Range 0° ~ +354° Tampering, Loitering, Directional Detection, Defocus Detection, Fog&Dust Detection,
Pan / Tilt /Rotate Tilt Range 0° ~ +67° Video & Audio Analytics Virtual Line, Enter/Exit, Appear / Disappear, Audio Detection, Face Detection, Motion
Detection, Digital Auto Tracking, Sound Classification
Rotate Range 0° ~ +355°
Alarm I/O Input 1ea / Output 1ea
XND-6080R/8080R/6080RV/8080RV : 30m(98.4ft)
IR Viewable Length - Alarm Triggers Alarm Input, Motion Detection, Video & Audio Analytics, Network Disconnect
XNV-6080R/8080R : 50m(164.04ft)
Off / On (Displayed up to 85 characters) yy File upload via FTP, E-Mail
Operational - W/W : English/Numeric/Special Characters yy Notification via E-Mail
Camera Title
- Common : Multi-line (Max 5), Color (Grey/Green/Red/Blue/Black/White),
Alarm events yy Local storage(SD/SDHC/SDXC) or NAS recording at Event (Alarm Triggers)
Transparency, Auto Scale by Resolution
yy External output
Day & Night Auto (ICR) / Color / B/W / External / Schedule
yy DPTZ preset
English _63
appendix
Description Description
Items XND-6080/XND-6080V/ XND-6080R/XND-6080RV/ XND-8080R/XND-8080RV/ Items XND-6080/XND-6080V/ XND-6080R/XND-6080RV/ XND-8080R/XND-8080RV/
XNV-6080 XNV-6080R XNV-8080R XNV-6080 XNV-6080R XNV-8080R
XND-6080/6080R/8080R/6080V/6080RV/8080RV : Selectable (Mic IN/Line IN/ Audio Communication Bi-directional (2-Way)
Built-in mic)
IP IPv4, IPv6
Audio In Supply voltage: 2.5VDC(4mA), Input impedance: approx. 2K Ohm
XNV-6080/6080R/8080R : Selectable (Mic IN/Line IN) TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS, SSL/TLS,
Operational
Supply voltage: 2.5VDC(4mA), Input impedance: approx. 2K Ohm Protocol DHCP, PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS,
QoS, PIM-SM, UPnP, Bonjour
Audio out Line out, Max output level: 1 Vrms
HTTPS(SSL) Login Authentication
Pixel Counter Support
Digest Login Authentication
Ethernet RJ-45 (10/100/1000BASE-T) Security IP Address Filtering
H.265/H.264 (MPEG-4 Part 10/AVC) : Main/Baseline/High User access Log
Video Compression Format
Motion JPEG 802.1x Authentication (EAP-TLS, EAP-LEAP)
2560x1920 / 2560x1440 / Streaming Method Unicast / Multicast
1920x1080 / 1600x1200
/ 1280x1024 / 1280x960 Max. User Access 20 users at Unicast Mode
1920x1080 / 1280x1024 / 1280x960 / 1280x720
/ 1280x720 / 1024x768
Resolution / 1024x768 / 800x600 / 800x448 / 720x576 / SD/SDHC/SDXC 2slot (up to 512 GB)
/ 800x600 / 800x448 /
720x480 / 640x480 / 640x360 / 320x240 - Continuous recording(1’st slot to 2’nd slot)
720x576 / 720x480 /
640x480 / 640x360 / Network Edge Storage - Motion Images recorded in the SD/SDHC/SDXC memory card can be downloaded.
320x240 NAS(Network Attached Storage)
H.265/H.264 : Max. 30fps Local PC for Instant Recording
H.265/H.264 : Max. 60fps at all resolutions
Max. Framerate at all resolutions
ONVIF Profile S/G
Motion JPEG : Max. 30fps Motion JPEG : Max. 30fps Application Programming
Network SUNAPI(HTTP API)
Interface
Smart Codec Manual mode(Area-based : 5ea) Open Platform
WiseStream Support English, Korean, French, German, Spanish, Italian, Chinese, Russian, Japanese,
Webpage Language
H.264/H.265 : Target Bitrate Level Control Swedish, Portuguese, Czech, Polish, Turkish, Dutch, Hungarian, Greek
Video Quality Adjustment
MJPEG : Target Bitrate Level Control Supported OS : Windows 7 / 8.1 / 10, MAC OS X 10.10, 10.11, 10.12
H.264/H.265 : CBR or VBR Plug-in free web viewer
Bitrate Control Method Supported web browsers : Google Chrome 54, MS Edge 38, Mozilla Firefox
Motion JPEG : VBR Web Viewer
49(Window 64bit only) , Apple Safari 9 (Mac OS X only)
Streaming Capability Multiple Streaming (Up to 10 Profiles) Plug-in web viewer
Supported web browsers : MS Explorer 11, Apple Safari 9 (Mac OS X only)
G.711 µ-law /G.726 Selectable
G.726 (ADPCM) 8KHz, G.711 8KHz Central Management
SmartViewer, SSM
Audio Compression Format Software
G.726 : 16Kbps, 24Kbps, 32Kbps, 40Kbps
AAC-LC : 48Kbps at 8/16/32/48KHz
64_ appendix
Description Product Overview
Items XND-6080/XND-6080V/ XND-6080R/XND-6080RV/ XND-8080R/XND-8080RV/ XND-6080/6080R/8080R
XNV-6080 XNV-6080R XNV-8080R Unit : mm (inch)
XND-6080/6080R/8080R/6080V/6080RV/8080RV : -10°C ~ +55°C (14°F ~
Operating Temperature / +131°F) / Less than 90% RH
●● appendix
Humidity
XNV-6080/6080R/8080R : -40°C ~ +55°C (-40°F ~ +131°F) / Less than 90% RH
Storage Temperature
-50°C ~ +60°C (-58°F ~ +140°F) / Less than 90% RH
/ Humidity
Environmental
XND-6080/6080R/8080R/6080V/6080RV/8080RV : -
Ingress Protection
XNV-6080/6080R/8080R : IP67, IP66, NEMA 4X
XND-6080/6080R/8080R/6080V/6080RV/8080RV : IK08
Vandal Resistance
XNV-6080/6080R/8080R : IK10
XND-6080/6080R/8080R//6080V/6080RV/8080RV : 12VDC ± 10%, PoE
Input Voltage / Current (IEEE802.3af)
XNV-6080/6080R/8080R : 24VAC ± 10%, 12VDC ± 10%, PoE (IEEE802.3af)
Electrical XND-6080/6080V : Max. 6W (12VDC), Max. 6.5W (PoE)
XND-6080R/8080R/6080RV/8080RV : Max. 9W (12VDC), Max. 10W (PoE)
Power Consumption
XNV-6080 : Max. 7W (12VDC), Max. 7.8W (PoE), Max. 8.2W (24VAC)
XNV-6080R/8080R : Max. 11.5W (12VDC), Max. 12.95W (PoE), Max. 14W (24VAC)
XND-6080/6080R/8080R/6080V : Ivory / Plastic
Color / Material
XND-6080RV/8080RV, XNV-6080/6080R/8080R : Ivory / Aluminum
XND-6080/6080R/8080R/6080V/6080RV/8080RV : Ø 140.8 X H113.0mm(Ø5.54”
Dimension (ØxH) x H4.45”)
XNV-6080/6080R/8080R : Ø 160 X H118.5mm (Ø6.3” x H4.67”)
XND-6080 : 610g(1.34lb)
XNV-6080 : 985g(2.17 lb)
Mechanical
XND-6080R : 624g(1.38lb)
XNV-6080R : 995g (2.19 lb)
Weight XND-8080R : 628g(1.38lb)
XNV-8080R : 1.01Kg (2.23 lb)
XND-6080V : 714g(1.57lb)
XND-6080RV : 724g(1.60lb)
XND-8080RV : 732g(1.61lb)
English _65
appendix
XND-6080V/6080RV/8080RV XNV-6080/6080R/8080R
Unit : mm (inch) Unit : mm (inch)
66_ appendix
Troubleshooting PROBLEM SOLUTION
PROBLEM SOLUTION <Motion detection> of <Analytics> is yy Verify the settings in the following sequence:
set to <Enable>, but no notification A. Check <Data & Time> settings.
When an Windows 10 user accesses e-mail reaches me even when an B. The <Motion detection> should be set to <Enable>.
yy This is what happens when microphone driver has been set to Realtek driver.
the web viewer through Chrome analysis event had occurred.
Install the High Definition Audio device (Windows Default Driver) or the third party driver as C. Check if the <E-mail> option of <Event setup> menu is checked to use.
●● appendix
or Firefox, the sound volume of
the microphone driver.
microphone changes periodically. Can I define event rules even when I
yy Yes, it can be. You can set rules for events despite of the intelligent video analysis setting.
don’t use <Motion detection>?
yy On the authentication popup window prompted when initially accessing https, click "View
Authentication Certificate" and select the "Always trust when connecting to the designated No signal is found at the Alarm Output
No video is displayed when accessing webviewer IP" check box.
the plug-in free webviewer on Safari port even when an intelligent video yy Check alarm output port settings.
via HTTPS. yy If the webviewer continues failing to display a video after you select "Next" on the message analysis event is generated.
window below, press the command key + Q to exit the Safari browser, access again and
follow the procedures stated above. Cannot record into the Micro SD
yy Check if the memory card is defective.
memory card.
yy Check to make sure that the camera’s Network settings are appropriate.
yy Check if the memory card is inserted in the proper direction. Operation of memory card that
yy Check to make sure that all network cables have been connected properly. Micro SD memory card is inserted but is formatted by other devices is not guaranteed with this camera unit
I can’t access the camera from a web yy If connected using DHCP, verify that the camera is able to acquire dynamic IP addresses the camera does not operate properly.
browser. yy Format the memory card again in <Setup>  <Event>  <Storage> menu.
without any problem.
yy If the camera is connected to a Broadband Router, verify that port forwarding is properly Cannot record in the NAS. yy Confirm that the information registered in the NAS is correct.
configured.
yy Confirm that the IP address of the NAS is valid.
yy Connected Viewers become disconnected upon any change to camera or network
configurations. yy Confirm that the ID/password of the NAS is valid.
Viewer got disconnected during yy Confirm that you can access the folder designated as the default folder using the ID of the
yy Check all network connections.
monitoring. NAS.
yy If the camera is connected over an PPPoE network, it’ s possible for Viewer to disconnect
under poor network conditions. yy Confirm that the NAS SMB/CIFS items are unchecked.
It reports that NAS setting has failed. yy Confirm that the NAS IP address and the camera IP address are in the same format.
The camera connected to the network ex) The NAS & camera subnet mask initial value is 255.255.255.0.
is not detected in the IP installer yy Turn off the firewall settings on your PC and then search the camera again. If the IP address is 192.168.20.32 then the NAS IP address should be in the range of
program. 192.168.20.1~192.168.20.255.
yy Check whether two or more cameras are set to a single multicast address instead of different yy Check whether you tried to access as another user without formatting the default folder
Images overlap. saved or used.
addresses. If a single address is used for multiple cameras, the images may overlap.
yy Confirm that you used recommended NAS equipment.
yy If the transmission method is set to multicast, check whether there is a router that supports
No image appears.
multicast in the LAN the camera is connected to.
English _67
Open Source Announcement GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
GPL/LGPL software license Copyright (C)1989, 1991 Free Software Foundation, Inc. 51 Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Preamble
Source code from us for a period of three years after our last shipment of this product by sending email to [email protected]
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source guarantee your freedom to share and change free software-- to make sure the software is free for all its users. This General Public License applies to most of the
distribution might be charged. Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered
by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you
GPL SW wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs ; and that you know
you can do these things.
Component Name License URL To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you modify it.
Base Kernel GPL 2.0
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have.
Busybox GPL 2.0 http://www.busybox.net/downloads/snapshots
iproute2-4.3.0 GPL 2.0 You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights
with two steps :
iptables-1.4.21 GPL 2.0 http://ftp.netfilter.org/pub/iptables
ethtool-4.2 GPL 2.0 (1)copyright the software, and (2)offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s
protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone
mtd-1.5.2 GPL 2.0 ftp://ftp.infradead.org/pub/mtd-utils else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the
mii-diag-2.11 GPL 2.0 original authors’ reputations.
rp-pppoe-3.11 GPL 2.0 http://www.roaringpenguin.com/pppoe/ Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain
wpa_supplicant-2.5 GPL 2.0 patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not
bash-4.3.30 GPL 3.0 licensed at all. The precise terms and conditions for copying, distribution and modification follow.
zeroconf GPL 2.0
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
LGPL SW
Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin S
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
Component Name License URL General Public License.
The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under
gLibc LGPL 2.0 copyright law : that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
Inetutils LGPL 3.0 (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
neon-0.29.6 LGPL 2.0 http://www.webdav.org/neon/ Activities other than copying, distribution and modification are not covered by this License ; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by
running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the
absence of any warranty ; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions :
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run,you must cause it, when started running for such interactive use in the most
ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that
you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
(Exception:if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print
an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably
considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate
works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you ; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program
(or with a work based on the Program)on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2)in object code or executable form under the terms of Sections 1 and 2
above provided that you also do one of the following :
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange ; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source
distribution, a complete machinereadable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange ; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial
distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code
for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for
all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However,
as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for the program,if necessary. Here is a
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source sample ; alter the names:
code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object Yoyodyne, Inc.,hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of
code. Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your
4. Y
ou may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is Lwihcaetn ysoeu want to do,
sublicense or distribute the Program is void, and will automatically terminate your rights under this License. use the GNU Lesser General Public instead of this License.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminatedso long as such parties remain in full GNU GENERAL PUBLIC LICENSE
compliance. Version 3, 29 June 2007
5. Y
ou are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/>
its derivative works. Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
These actions are prohibited by law if you do not accept this License.Therefore, by modifying or distributing the Program (or any work based on the Program), you Preamble
indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to
distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights share and change all versions of a program-- to make sure it remains free software for all its users.
granted herein. You are not responsible for enforcing compliance by third parties to this License. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its
authors.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)that contradict the conditions of this License, they do not excuse you from the conditions of this License. You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to
If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you
may not distribute the Program at all. want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities
For example, if a patent license would not permit royaltyfree redistribution of the Program by all those who receive copies directly or indirectly through you, then
if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a
the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two
a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it. For the developers’ and
contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by authors’ protection, the GPL clearly explains that there is no arranty for this free software. For both users’ and authors’ sake, the GPL requires that modified
public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny
application of that system ; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the
impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is
precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of
places the Program under this License may add an explicit geographical distribution limitation excluding those countries,so that distribution is permitted only
users.
in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar
purpose omputers, but in those that do, we wish to avoid the special anger that patents applied to a free program could make it ffectively proprietary. To prevent
in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the
this, the GPL assures that atents cannot be used to render the program non-free. he precise terms and conditions for copying, distribution and modification
Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either
follow.
of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may
choose any version ever published by the Free Software Foundation.
TERMS AND CONDITIONS
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.
For software which is copyrighted by the Free Software Foundation,write to the Free Software Foundation ; we sometimes make exceptions for this. Our 0. Definitions.
decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software “This License” refers to version 3 of the GNU General Public License.
generally. Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. “The Program” refers to any copyrightable work
licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
NO WARRANTY
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
A “covered work” means either the unmodified Program or a work based on the Program.
“ASIS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable
WITH YOU. SHOULD THE PROGRAMPROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. copyright law, except executing it on a computer or modifying a private copy.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
WHO MAY MODIFY AND/OR REDISTRIBUTE DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH network, with no transfer of a copy, is not conveying. An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent
that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of
END OF TERMS AND CONDITIONS user commands or options, such as a menu, a prominent item in the list meets this criterion.
How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way 1. Source Code.
to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty ; and each file should have at least the “copyright” The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
line and a pointer to where the full notice is found.one line to give the program’s name and an idea of what it does. A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a
Copyright (C)yyyy name of author particular programming language, one that is widely used among developers working in that language.
This program is free software ; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major
Foundation ; either version 2 of the License, or (at your option)any later version. Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a
Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY ; without even the implied warranty of MERCHANTABILITY or component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. work, or an object code interpreter used to run it.
You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object
Street, Fifth Floor, Boston, MA 02110-1301, USA. code and to modify the work, including scripts to control those activities.
Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an
interactive mode : However, it does not include the work’s System Libraries, or generalpurpose tools or generally available free programs which are used unmodified in performing
those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY ; for details type ‘show w’. This is free software, work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data
and you are welcome to redistribute it under certain conditions ; type ‘show c’ for details. communication or control flow between those subprograms and other parts of the work.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. The Corresponding
be called something other than ‘show w’ and ‘show c’ ; they could even be mouse-clicks or menu items-- whatever suits your program. Source for a work in source code form is that same work.
2. Basic Permissions. The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that
has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This
the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an
output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey
7. Additional Terms.
covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided
that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for “Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions
you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If
their relationship with you. Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed
makes it unnecessary. by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional
permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the
3. Protecting Users’ Legal Rights From anti-Circumvention Law.
work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material)
treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. supplement the terms of this License with terms:
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of
enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures. b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works
containing it; or
4. Conveying Verbatim Copies.
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on from the original version; or
each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply
to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program. You may charge any d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
price or no price for each copy that you convey, and you may offer support or warranty protection for a fee. e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
5. Conveying Modified Source Versions. f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors. All other
provided that you also meet all of these conditions: non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it,
contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document
a) The work must carry prominent notices stating that you modified it, and giving a relevant date. contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms
of that license document, provided that the further restriction does not survive such relicensing or conveying. If you add terms to a covered work in
b) T
he work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating
the requirement in section 4 to “keep intact all notices”. where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along exceptions; the above requirements apply either way.
with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no 8. Termination.
permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
display Appropriate Legal Notices, your work need not make them do so. A compilation of a covered work with other separate and independent works,
which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright
a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior
the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you ofthe violation
other parts of the aggregate. by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the
violation prior to 30 days after your receipt of the notice. Termination of your rights under this section does not terminate the licenses of parties who have received
6. Conveying Non-Source Forms. copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding same material under section 10.
Source under the terms of this License, in one of these ways: 9. Acceptance Not Required for Having Copies.
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a
fixed on a durable physical medium customarily used for software interchange. consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating
three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code a covered work, you indicate your acceptance of this License to do so.
either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily 10. Automatic Licensing of Downstream Recipients.
used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the
Corresponding Source from a network server at no charge. Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject
to this License. You are not responsible for enforcing compliance by third parties with this License. An “entity transaction” is a transaction transferring control
c) Convey individual copies of the object code with a copy of the written offer to provide the corresponding Source. This alternative is allowed only of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from
occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b. an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if
in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object the predecessor has it or can get it with reasonable efforts. You may not impose any further restrictions on the exercise of the rights granted or affirmed under
code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party) this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate
that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing
Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these the Program or any portion of it.
requirements. 11. Patents.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed
work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded is called the contributor’s “contributor version”. A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether
from the Corresponding Source as a System Library, need not be included in conveying the object code work. A “User Product” is either (1) a “consumer already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version,
product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control”
sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For includes the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive,
a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of worldwide, royaltyfree patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and
the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product propagate the contents of its contributor version.
regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of
use of the product. In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an
express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowingly relying on a patent license, and the Corresponding
versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other
functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the
work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream
and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your
Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid. If,
retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM). pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, 6. R
edistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for
then the patent license you grant is automatically extended to all recipients of the covered work and works based on it. A patent license is “discriminatory” if it use in the OpenSSL Toolkit (http://www.openssl.org/)"
does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically
granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT `ÀS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants, TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
to any of the parties who would receive the covered work from you, a discriminatory patent license OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
(a) in connection with copies of the covered work conveyedby you (or copies made from those copies), or BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
(b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to This product includes cryptographic software written by Eric Young([email protected]). This product includes software written by Tim Hudson ([email protected]).
infringement that may otherwise be available to you under applicable patent law.
Original SSLeay License
12. No Surrender of Others’ Freedom.
Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from
the conditions of thisLicense. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent This package is an SSL implementation written by Eric Young ([email protected]).
obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying
from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the The implementation was written so as to conform with Netscapes SSL.
Program. This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found
13. Use with the GNU Affero General Public License. in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the
same copyright terms except that the holder is Tim Hudson ([email protected]).
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU
Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should
the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online
combination as such. or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following
conditions are met:
14. Revised Versions of this License.
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
The Free Software Foundation may publish revised and/ or new versions of the GNU General Public License from time to time. Such new versions will be similar
in spirit to the present version, but may differ in detail to address new problems or concerns. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later
version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes cryptographic
Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the software written by Eric Young ([email protected])" The word 'cryptographic' can be left out if the rouines from the library being used are not cryptographic
Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s related :-).
public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional 4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This
or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version. product includes software written by Tim Hudson (tjh@cryptsoft. com)"
15. Disclaimer of Warranty. THIS SOFTWARE IS PROVIDED BY ERIC YOUNG `ÀS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
16. Limitation of Liability. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and
put under another distribution licence [including the GNU Public Licence.]
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
BSD License
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO Some software components of this product incorporate source code covered under the BSD license as follows.
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Component Name License URL
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply net-snmp-5.7.3 BSD http://www.net-snmp.org/about/license.html
local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability
pcre-8.38 BSD
accompanies a copy of the Program in return for a fee.
libcap-1.7.4 BSD 2.0 http://www.kernel.org/pub/linux/libs/security/linux-privs/libcap2
OpenSSL Combined License lighttpd-1.4.35 BSD 2.0 http://www.opensource.org/licenses/bsd-license.html
MiniUPnP Project Client BSD 2.0
pppd-2.4.7 BSD 2.0 http://opensource.org/licenses/BSD-3-Clause
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please
contact [email protected]. lighttpd is a secure, fast, compliant, and very flexible webserver that has been optimized for high-performance environments. It has a very low memory footprint
compared to other webservers and takes care of cpuload. Its advanced feature-set (FastCGI, CGI, Auth, Output-Compression, URL-Rewriting and many more)
make lighttpd the perfect webserver-software for every server that suffers load problems. Simple Network Management Protocol (SNMP) is an Internetstandard
protocol for managing devices on IP networks. It is used mostly in network management systems to monitor the devices attached to the network for conditions
that need administrative attention. Net-SNMP is a suite of applications used to implement SNMP v1, SNMP v2c and SNMP v3 using both IPv4 and IPv6. For
openssl-1.0.2e OpenSSL Combined License http://www.openssl.org/source more additional information, send email to [email protected].
Copyright (C) 2004, Kneschke, incremental
Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met :
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed
by the OpenSSL Projectfor use in the OpenSSL Toolkit. (http://www.openssl.org/)" - Neither the name of the ‘incremental’ nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission.
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written
permission. For written permission, please contact [email protected].
5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the
OpenSSL Project.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. OF SUCH DAMAGE.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
Various copyrights apply to this package, listed in various separate parts below. Please make sure that you read all the parts.
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR Part 1: CMU/UCD copyright notice: (BSD like)
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE. Copyright 1989, 1991, 1992 by Carnegie Mellon University Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the University of California
Copyright (c) 1998-2001 University College London
All Rights Reserved
Permission to use, copy, modify and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above
Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met : copyright notice appears in all copies and that both that copyright notice and this permission notice appear in supporting documentation, and that the name
of CMU and The Regents of the University of California not be used in advertising or publicity pertaining to distribution of the software without specific written
permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE UNIVERSITY OF CALIFORNIA BE
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA
by the Computer Science Department at University College London. OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE
USE OR PERFORMANCE OF THIS SOFTWARE.
4. Neither the name of the University nor of the Department may be used to endorse or promote products derived from this software without specific prior
written permission. Part 2 : Networks Associates Technology, Inc copyright notice (BSD)
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND CONTRIBUTORS `ÀS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT Copyright (c) 2001-2003, Networks Associates Technology, Inc
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSEARE DISCLAIMED. IN NO EVENT
SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of the Networks Associates Technology, Inc nor the names of its contributors may be used to endorse or promote products derived from this software
Copyright (c) 1988, 1989, 1990, 1991, 1993, 1994, 1995, 1996 The Regents of the University of California.
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
other materials provided with the distribution. TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
3. Neither the name of the Regents of the University of California nor the names of its contributors may be used to endorse or promote products derived from
this software without specific prior written permission. Part 3: Cambridge Broadband Ltd. copyrightnotice (BSD)
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, Portions of this code are copyright (c) 2001-2003, Cambridge Broadband Ltd.
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy The
OF SUCH DAMAGE. name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived from this software without specific prior written permission.
Copyright (c) 2006, Creative Labs Inc THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or Part 4: Sun Microsystems, Inc. copyright notice
(BSD)
3. Neither the name of the Creative Labs nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission. Copyright (c) 2003 Sun Microsystems, Inc., 4150 Network
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, Circle, Santa Clara, California 95054, U.S.A.
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR Use is subject to license terms below. This distribution may include materials developed by third parties. Sun, Sun Microsystems, the Sun logo and Solaris
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Redistribution and use in source and binary forms, with or
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice,
OF SUCH DAMAGE. this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of the Sun Microsystems, Inc. nor the
Copyright (c) 2005-2012, Thomas BERNARD
names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
other materials provided with the distribution. TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
3. Neither the name of Thomas BERNARD nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission. Part 5: Sparta, Inc copyright notice (BSD)
Copyright (c) 2003-2009, Sparta, Inc
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. All rights reserved.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither The MIT License
the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, Some software components of this product incorporate source code covered under the MIT license as follows
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, MIT License 2.0
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
- Acewidget, bettermeans, jquery-ui, libxml, libxml2, Mesa3D-MesaLib,mwEmbed,OpenGL Samples Pack, Wide Studio, xorg-server, dropbear-2012.55,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
ncurses-5.7
OF SUCH DAMAGE.
Part 6: Cisco/BUPTNIC copyright notice (BSD) Copyright (c) 2011, The Dojo Foundation
Copyright (c) 2004, Cisco, Inc and Information Network Copyright 2010, AUTHORS.txt (http://jqueryui.com/about)
Center of Beijing University of Posts and Telecommunications. Dual licensed under the MIT or GPL Version 2 licenses.
All rights reserved. - http://jquery.org/license
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions - http://docs.jquery.com/UI/Widget
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the Copyright Daniel Veillard
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of Cisco, Inc, Beijing University of Posts and Telecommunications, nor the names of their contributors may be used to endorse or promote products Copyright Igor Zlatovic <[email protected]>
derived from this software without specific prior written permission. Copyright Aleksey Sanin
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, Copyright Gary Pennington <[email protected]>
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, Copyright Alfred Mickautsch <[email protected]>
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, Copyright Bjorn Reese <[email protected]>
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY Copyright Joel W. Reed
OF SUCH DAMAGE. Copyright William Brack <[email protected]>
Part 7: Fabasoft R&D Software Software GmbH & Co KG copyright Notice (BSD) Copyright (c) 2007-2010 The Khronos Group Inc.
Copyright (c) Fabasoft R&D Software GmbH & Co KG, [email protected] Copyright Atish Kumar Patra
Author: Bernhard Penz Copyright (c) 2006 Free Software Foundation, Inc.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software,
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy The and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
name of Fabasoft R&D Software GmbH & Co KG or any of its subsidiaries, brand or product names may not be used to endorse or promote products derived
from this software without specific prior written permission. The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Mozilla Public License
Part 8: Apple Inc. copyright notice (BSD)
Copyright (c) 2007 Apple Inc.
Since we, at Hanwha Techwin, used the Mozilla Firefox component without modifying the source code according to the MOZILLA Public license 1.1, we
All rights reserved. are not obliged to provide the source code of the corresponding component.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: •• Version 1.1
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or 1. Definitions.
other materials provided with the distribution. 3. Neither the name of Apple Inc. (“Apple”) nor the names of its contributors may be used to endorse or promote 1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party.
products derived from this software without specific prior written permission.
1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications.
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT 1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor, and the Modifications made by that particular Contributor.
SHALL APPLE OR ITSCONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and Modifications, in each case including portions thereof.
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 1.4. "Electronic Distribution Mechanism" means a mechanism generally accepted in the software development community for the electronic transfer of data.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 1.5. "Executable" means Covered Code in any form other than Source Code.
Part 9: ScienceLogic, LLC copyright notice(BSD) 1.6. "Initial Developer" means the individual or entity identified as the Initial Developer in the Source Code notice required by Exhibit A.
Copyright (c) 2009, ScienceLogic, LLC 1.7. "Larger Work" means a work which combines Covered Code or portions thereof with code not governed by the terms of this License.
All rights reserved. 1.8. "License" means this document.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions aremet: yy Redistributions 1.8.1. "Licensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the rights conveyed herein.
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of ScienceLogic, LLC nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior 1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or any previous Modifications. When Covered Code is
written permission. released as a series of files, a Modification is:
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, A. Any addition to or deletion from the contents of a file containing Original Code or previous Modifications.
B. Any new file that contains any part of the Original Code or previous Modifications.
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, 1.10. "Original Code" means Source Code of computer software code which is described in the Source Code notice required by Exhibit A as Original Code, and which,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR at the time of its release under this License is not already Covered Code governed by this License.
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY 1.10.1. "Patent Claims" means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent
OF SUCH DAMAGE Licensable by grantor.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface for the Executable version does not attempt to limit or alter the recipient’s rights in the Source Code version from the rights set forth in this License. If You distribute
definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another the Executable version under a different license You must make it absolutely clear that any terms which differ from this License are offered by You alone, not by the
well known, available Covered Code of the Contributor’s choice. The Source Code can be in a compressed or archival form, provided the appropriate decompression or Initial Developer or any Contributor. You hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or such
de-archiving software is widely available for no charge. Contributor as a result of any such terms You offer.
1.12. "You’’ (or "Your") means an individual or a legal entity exercising rights under, and complying with all of the terms of, this License or a future version of this License 3.7. Larger Works. You may create a Larger Work by combining Covered Code with other code not governed by the terms of this License and distribute the Larger Work
issued under Section 6.1. For legal entities, "You’’ includes any entity which controls, is controlled by, or is under common control with You. For purposes of this as a single product. In such a case, You must make sure the requirements of this License are fulfilled for the Covered Code.
definition, "control’’ means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of
4. Inability to Comply Due to Statute or Regulation.
more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered Code due to statute, judicial order, or regulation then
2. Source Code License.
You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must
2.1. The Initial Developer Grant. The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property be included in the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to the extent prohibited by statute or
claims: regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it.
(a) u
nder intellectual property rights (other than patent or trademark) Licensable by Initial Developer to use, reproduce, modify, display, perform, sublicense and 5. Application of this License.
distribute the Original Code (or portions thereof) with or without Modifications, and/or as part of a Larger Work; and This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to related Covered Code.
(b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise 6. Versions of the License.
dispose of the Original Code (or portions thereof).
6.1. New Versions. Netscape Communications Corporation (‘’Netscape’’) may publish revised and/or new versions of the License from time to time. Each version will be
(c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes Original Code under the terms of this License. given a distinguishing version number.
(d) Notwithstanding Section 2.1(b) above, no patent license is granted: 1) for code that You delete from the Original Code; 2) separate from the Original Code; or 6.2. Effect of New Versions. Once Covered Code has been published under a particular version of the License, You may always continue to use it under the terms of that
3) for infringements caused by: i) the modification of the Original Code or ii) the combination of the Original Code with other software or devices. version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape
2.2. Contributor Grant. Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free, non-exclusive license has the right to modify the terms applicable to Covered Code created under this License.
(a) u
nder intellectual property rights (other than patent or trademark) Licensable by Contributor, to use, reproduce, modify, display, perform, sublicense and 6.3. Derivative Works. If You create or use a modified version of this License (which you may only do in order to apply it to code which is not already Covered Code
distribute the Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/ governed by this License), You must (a) rename Your license so that the phrases "Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar
or as part of a Larger Work; and phrase do not appear in your license (except to note that your license differs from this License) and (b) otherwise make it clear that Your version of the license contains
terms which differ from the Mozilla Public License and Netscape Public License. (Filling in the name of the Initial Developer, Original Code or Contributor in the notice
(b) under Patent Claims infringed by the making, using, or selling of Modifications made by that Contributor either alone and/or in combination with its described in Exhibit A shall not of themselves be deemed to be modifications of this License.)
Contributor Version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) Modifications made by
that Contributor (or portions thereof); and 2) the combination of Modifications made by that Contributor with its Contributor Version (or portions of such 7. DISCLAIMER OF WARRANTY.
combination). COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN "AS IS’’ BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
(c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date Contributor first makes Commercial Use of the Covered Code. WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-
INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE
(d) Notwithstanding Section 2.2(b) above, no patent license is granted: 1) for any code that Contributor has deleted from the Contributor Version; 2) separate from the DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING,
Contributor Version; 3) for infringements caused by: i) third party modifications of Contributor Version or ii) the combination of Modifications made by that Contributor REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS
with other software (except as part of the Contributor Version) or other devices; or 4) under Patent Claims infringed by Covered Code in the absence of Modifications AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
made by that Contributor.
8. TERMINATION.
3. Distribution Obligations.
8.1. This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of
3.1. Application of License. The Modifications which You create or to which You contribute are governed by the terms of this License, including without limitation Section
becoming aware of the breach. All sublicenses to the Covered Code which are properly granted shall survive any termination of this License. Provisions which, by their
2.2. The Source Code version of Covered Code may be distributed only under the terms of this License or a future version of this License released under Section 6.1,
nature, must remain in effect beyond the termination of this License shall survive.
and You must include a copy of this License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source Code version that
alters or restricts the applicable version of this License or the recipients’ rights hereunder. However, You may include an additional document offering the additional rights 8.2. If You initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against Initial Developer or a Contributor (the Initial Developer
described in Section 3.5. or Contributor against whom You file such action is referred to as "Participant") alleging that:
3.2. Availability of Source Code. Any Modification which You create or to which You contribute must be made available in Source Code form under the terms of this (a) such Participant’s Contributor Version directly or indirectly infringes any patent, then any and all rights granted by such Participant to You under Sections 2.1 and/
License either on the same media as an Executable version or via an accepted Electronic Distribution Mechanism to anyone to whom you made an Executable version or 2.2 of this License shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice You either: (i) agree in writing
available; and if made available via Electronic Distribution Mechanism, must remain available for at least twelve (12) months after the date it initially became available, or to pay Participant a mutually agreeable reasonable royalty for Your past and future use of Modifications made by such Participant, or (ii) withdraw Your litigation claim
at least six (6) months after a subsequent version of that particular Modification has been made available to such recipients. You are responsible for ensuring that the with respect to the Contributor Version against such Participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed
Source Code version remains available even if the Electronic Distribution Mechanism is maintained by a third party. upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by Participant to You under Sections 2.1 and/or 2.2 automatically terminate at
3.3. Description of Modifications. You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to create that Covered the expiration of the 60 day notice period specified above.
Code and the date of any change. You must include a prominent statement that the Modification is derived, directly or indirectly, from Original Code provided by the Initial (b) any software, hardware, or device, other than such Participant’s Contributor Version, directly or indirectly infringes any patent, then any rights granted to You by such
Developer and including the name of the Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in which You Participant under Sections 2.1(b) and 2.2(b) are revoked effective as of the date You first made, used, sold, distributed, or had made, Modifications made by that
describe the origin or ownership of the Covered Code. Participant.
3.4. Intellectual Property Matters 8.3. If You assert a patent infringement claim against Participant alleging that such Participant’s Contributor Version directly or indirectly infringes any patent where
such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such
(a) Third Party Claims. If Contributor has knowledge that a license under a third party’s intellectual property rights is required to exercise the rights granted by such Participant under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the Source Code distribution titled "LEGAL’’ which describes the claim and the party
making the claim in sufficient detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is made available as 8.4. In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by
described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies Contributor makes available thereafter and shall take other steps (such as You or any distributor hereunder prior to termination shall survive termination.
notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has been obtained. 9. LIMITATION OF LIABILITY.
(b) Contributor APIs. If Contributor’s Modifications include an application programming interface and Contributor has knowledge of patent licenses which are reasonably UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE
necessary to implement that API, Contributor must also include this information in the LEGAL file. INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO
(c) Representations. ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above, Contributor believes that Contributor’s Modifications are Contributor’s original
IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY
creation(s) and/or Contributor has sufficient rights to grant the rights conveyed by this License.
FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY’S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME
3.5. Required Notices. You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a particular Source Code file JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY
due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created NOT APPLY TO YOU. 10. U.S. GOVERNMENT END USERS.
one or more Modification(s) You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License in any documentation for
The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial
the Source Code where You describe recipients’ rights or ownership rights relating to Covered Code. You may choose to offer, and to charge a fee for, warranty, support,
computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through
indemnity or liability obligations to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of the Initial Developer
227.7202-4 (June 1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein.
or any Contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by You alone, and You hereby agree to
indemnify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or such Contributor as a result of warranty, support, indemnity or 11. MISCELLANEOUS.
liability terms You offer.
This License represents the complete agreement concerning subject matter hereof. If any provision of this License is held to be unenforceable, such provision shall
3.6. Distribution of Executable Versions. You may distribute Covered Code in Executable form only if the requirements of Section 3.1-3.5 have been met for that Covered be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if
Code, and if You include a notice stating that the Source Code version of the Covered Code is available under the terms of this License, including a description of how any, provides otherwise), excluding its conflictof-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered
and where You have fulfilled the obligations of Section 3.2. The notice must be conspicuously included in any notice in an Executable version, related documentation or to do business in the United States of America, any litigation relating to this License shall be subject to the jurisdiction of the Federal Courts of the Northern District of
collateral in which You describe recipients’ rights relating to the Covered Code. You may distribute the Executable version of Covered Code or ownership rights under California, with venue lying in Santa Clara County, California, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys’
a license of Your choice, which may contain terms different from this License, provided that You are in compliance with the terms of this License and that the license fees and expenses. The application of the United Nations Convention on Contracts for the International Sale of Goods is expressly excluded. Any law or regulation which
provides that the language of a contract shall be construed against the drafter shall not apply to this License. ansi2knr.c is NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that
you must include source code if you redistribute it. (See the file ansi2knr.c for full details.) However, since ansi2knr. c is not needed as part of any program
12. RESPONSIBILITY FOR CLAIMS.
generated from the IJG code, this does not limit you more than the foregoing paragraphs do.
As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under
The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free Software Foundation but is freely distributable. The same
this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be
holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain. sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable.
deemed to constitute any admission of liability.
It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally
13. MULTIPLE-LICENSED CODE.
be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software. (Since arithmetic
Initial Developer may designate portions of the Covered Code as Multiple-Licensed. Multiple-Licensedmeans that the Initial Developer permits you to utilize portions of coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.) So far as we are aware,
the Covered Code under Your choice of the MPL or the alternative licenses, if any, specified by the Initial Developer in the file described in Exhibit A. there are no patent restrictions on the remaining code.
EXHIBIT A -Mozilla Public License. The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the Unisys LZW patent, GIF reading support has been removed
altogether, and the GIF writer has been simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the resulting GIF files are
The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this file except in compliance with the License. You may larger than usual, but are readable by all standard GIF decoders.
obtain a copy of the License at http://www.mozilla.org/MPL/Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
KIND, either express or implied. See the License for the specific language governing rights and limitations under the License. We are required to state that
The Original Code is ___________________________________. "The Graphics Interchange Format(c) is the Copyright property of CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."
The Initial Developer of the Original Code is ________________________. Portions created by ______________________ are Copyright (C) ______
_______________________. All Rights Reserved. T-Kernel License
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the terms of the _____ license (the [___] License), in which case the provisions of [______] License are applicable - This Product uses the Source Code of T-Kernel under T-License granted by the T-Engine Forum(www.t-engine.org)
instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] License and not to allow others to use your version of this file
under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] License. If you do not
delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] License."
T-License [License Agreement for Source Code of T-Kernel]
[NOTE: The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the Original Code. You should use the text of this Exhibit A
rather than the text found in the Original Code Source Code for Your Modifications established by T-Engine Forum
on January 23, 2004
The Independent JPEG Group’s JPEG Software revised on June 17, 2004
revised on December 21, 2006
revised on March 24, 2009
The software included in this product contains copyrighted software that is licensed under the JPEG license. Article 1. Scope of License Agreement
•• JPEG license
-- Code project . Generating Outline OpenGL, Libjpeg 1. This License Agreement sets forth copyrights and the terms and conditions of use applicable to the source code of T-Kernel distributed by T-Engine Forum
and any derivative work created therefrom.
This distribution contains the sixth public release of the Independent JPEG Group’s free JPEG software. You are welcome to redistribute this software and to use it for Article 2. Definition
any purpose, subject to the conditions under LEGAL ISSUES, below.
1. "T-Kernel" means a real-time operating system controlled and distributed by T-Engine Forum on behalf of the copyright holder thereof.
Serious users of this software (particularly those incorporating it into larger programs) should contact IJG at [email protected] to be added to our electronic mailing
list. Mailing list members are notified of updates and have a chance to participate in technical discussions, etc. 2. "Source Code" means a source program, including related comments and documentations, for the T-Kernel and the Ported Source Code defined in Article 2.8
This software is the work of Tom Lane, Philip Gladstone, Jim Boucher, Lee Crocker, Julian Minguillon, Luis Ortiz, George Phillips, Davide Rossi, Guido Vollbeding, Ge’ which is registered with T-Engine Forum.
Weijers, and other members of the Independent JPEG Group.
3. "Hardware-dependent Part" means the part of the Source Code which depends on hardware and needs to be changed when the Source Code is ported and
IJG is not affiliated with the official ISO JPEG standards committee. operated on the target hardware, and is designated and separated as such part.
LEGAL ISSUES 4. "Compiler-dependent Part" means the part of the Source Code which depends on compiler and needs to be changed when the Source Code is ported and
============ operated on the target hardware, and is designated and separated as such part.
In plain English: 5. "Header File" means the part of the Source Code which contains definitions necessary to develop application programs.
1. We don’t promise that this software works. (But if you find any bugs, please let us know!)
6. "T-Engine Hardware" means the hardware which is manufactured in accordance with the T-Engine Hardware specifications or the μT-Engine Hardware
2. Y
ou can use this software for whatever you want. You don’t have to pay us. specifications issued by T-Engine Forum, and registered with T-Engine Forum.
3. Y
ou may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you’ve used the
IJG code. 7. "Similar Hardware to T-Engine Hardware" means any hardware (including software which emulates hardware) other than that defined in Article 2.6 above, on
which the T-Kernel can be operated.
In legalese:
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for 8. "Ported Source Code" means a source program produced from the Source Code by modifying only its Hardwaredependent Part and/or Compiler-dependent
a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy. Part to enable it to be operated on the T-Engine Hardware or the Similar Hardware to T-Engine Hardware. The Ported Source Code which is registered with
T-Engine Forum shall be included in the Source Code.
This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions: 9. "Modified Source Code" means a source program modified from the Source Code for the purpose of improving its performance, increasing or decreasing its
function, and the like. The Ported Source Code shall not be included in the Modified Source Code.
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered;
and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation. 10. "Binary Code" means an executable code form which is created by compiling programs, which include all or part of the Source Code or the Modified Source
(2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent Code.
JPEG Group".
11. "Derivative Work" means the Modified Source Code or the Binary Code.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY
for damages of any kind. 12. "Embedded Product" means any product which operates with executable code form of the Source Code, the Modified Source Code or the Binary Code
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge loaded on its hardware.
us.
13. "End User" means a consumer who uses the Embedded Product.
Permission is NOT granted for the use of any IJG author’s name or company name in advertising or publicity relating to this software or products derived from it.
This software may be referred to only as "the Independent JPEG Group’s software". 14. "System Developer" means any person who develops the Embedded Product by itself or has a third party develop the same, and provides, whether with or
We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by without payment, the End User with the Embedded Product.
the product vendor.
15. "Distributor of Modification" means any person who produces the Modified Source Code and, whether with or without payment, distributes the same to any
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. third party.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary Source Code on the T-Engine Hardware or the Similar Hardware to T-Engine Hardware:
Code thereof.
1. ‌The Hardware-dependent Part and/or Compiler-dependent Part; provided that the Source Code User and the System Developer shall inform T-Engine Forum
17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the of, and T-Engine Forum may publish, a method for distributing said Part(s) to third parties.
Source Code or the Binary Code thereof.
2. ‌The Header File; provided that the Header File shall be distributed together with the Binary Code of the Ported Source Code.
18. "Source Code User" means a person who uses the Source Code.
2. Any member of T-Engine Forum may request T-Engine Forum to register and distribute, as an original source code for T-Kernel, the Ported Source Code on
19. "Distribution" means any of the following acts: the T-Engine Hardware or the Similar Hardware to T-Engine Hardware.
1. ‌to transmit a work to a large number of specific persons through the Internet communication, broadcasting, and the like; 3. Any member of T-Engine Forum who requests the distribution mentioned in the preceding paragraph shall accede to the following conditions:
2. ‌to transmit a work to the general public through the Internet communication, broadcasting, and the like automatically in response to a request from the 1. ‌The member shall confirm that the object hardware is the T-Engine Hardware or the Similar Hardware to T-Engine Hardware.
public; and
2. ‌The member shall provide T-Engine Forum with a complete set of operational environment for the object hardware and T-Kernel free of charge when
3. ‌to distribute a copy of a work to the general public or a large number of specific persons. requesting the distribution.
Article 3. Copyright 3. ‌The member shall submit test results of the Ported Source Code to T-Engine Forum when requesting the distribution.
1. The copyrights of the Source Code shall be owned by Ken Sakamura. 4. In the event that T-Engine Forum accepts the request mentioned in Article 6.2, T-Engine Forum shall register and distribute the Ported Source Code as the
Source Code for T-Kernel. Provided, however, that the Ported Source Code may be treated in the same way as the Modified Source Code until the time of
Article 4. License of Source Code registration hereunder.
1. As provided for in this Article, T-Engine Forum shall provide, and grant a license to use, the Source Code free of charge to any person who has taken the 5. The provision set forth in Article 3 shall apply to the Ported Source Code registered in accordance with this Article.
necessary procedure for registration as prescribed by T-Engine Forum and agreed to the T-License.
Article 7. Use for Other Purpose
2. The Source Code shall be distributed exclusively by T-Engine Forum. Any person who obtains the Source Code under Article 4.1 above shall not make any
re-Distribution of the Source Code. 1. Any use of the Source Code, the Modified Source Code or the Ported Source Code other than those stipulated in Articles 4, 5 and 6 shall be subject to the
prior approval of T-Engine Forum.
3. In accordance with the license granted under Article 4.1 above, the Source Code User may perform the following acts:
Article 8. Limited Warranty
1. ‌to copy and/or modify the Source Code provided by T-Engine Forum hereunder for its own research, development and the like.
1. T-Engine Forum and the copyright holder of the Source Code warrant that the Source Code does not infringe third party’s copyrights. Provided, however, that
2. ‌to run the Source Code provided by T-Engine Forum hereunder for its own research, development and the like. T-Engine Forum and the copyright holder of the Source Code make no warranty as to the Hardware-dependent Part and/or Compiler- dependent Part set forth
in Article 6.2 in the Ported Source Code by any third party.
3. ‌to run the Source Code modified in accordance with the provision of Article 4.3 (1) above for its own research, development and the like.
2. Neither T-Engine Forum nor the copyright holder of the Source Code warrants that the Source Code will fit for any particular purpose of the Source Code
4. ‌to distribute the Binary Code created from the Source Code provided by T-Engine Forum hereunder or from the Source Code modified in accordance with User.
the provision of Article 4.3 (1) above.
3. Neither T-Engine Forum nor the copyright holder of the Source Code warrants that the Source Code does not infringe any third party’s industrial property
4. In accordance with the license granted under Article 4.1 above, the System Developer may perform the following acts: rights. In no event shall T-Engine Forum and the copyright holder of the Source Code be liable for any dispute which may arise between the Source Code User
and a third party in connection with the third party’s industrial property rights.
1. ‌to perform any and all acts set forth in the Article 4.3 above.
Article 9. Indemnity
2. ‌to develop and manufacture the Embedded Product containing the Binary Code, and, whether with or without payment, provide the End User with the same
and make the Binary Code available to the End User on the Embedded Product. 1. Neither T-Engine Forum nor the copyright holder of the Source Code shall be liable for any damages (including, but not limited to, damages resulting from
loss of profit, business interruption, loss of business information or any other pecuniary damage) arising out of use or impossibility of use of the Source Code,
5. The Source Code User and the System Developer shall be obligated to give a notice that the Source Code is used, in such a way as separately specified by even if T-Engine Forum and the copyright holder have been informed of the possibility of such damages.
T-Engine Forum, when they use the Source Code or the Binary Code, or make the Binary Code available for the End User on the Embedded Product.
Article 10. Breach of Agreement
Article 5. Distribution of Modified Source Code
1. In case that T-Engine Forum considers that this License Agreement is breached or that the popularization of T-Kernel is obstructed, T-Engine Forum shall take
1. Any of A- members of T-Engine Forum may become the Distributor of Modification by obtaining the approval of T-Engine Forum through the registration measures to correct such breach or such obstruction, take measures on the ground of copyright infringement, or take any other necessary measures against
procedure as prescribed by the Forum provided that only the department of the A- member which has taken the registration procedure may distribute the the breaching person or the obstructing person, regardless of whether or not the said person is a member of T-Engine Forum.
Modified Source Code in such a way as provided for in this Article as long as it holds the Amembership.
2. In case of breach of this License Agreement by a member of T-Engine Forum, T-Engine Forum may take appropriate measures against the member; for
2. The Distributor of Modification may create the Modified Source Code based on the Source Code provided by T-Engine Forum and the Patch for Modification example, the member is disqualified from membership, depending on what kind of breach has been committed by it.
to be applied to create such Modified Source Code from the Source Code.
3. Any legal dispute which may arise in relation to any breach of this License Agreement shall be subject to the exclusive jurisdiction of the Tokyo District Court.
3. The Distributor of Modification shall, prior to the distribution, inform T-Engine Forum of and register a name and description of the Modified Source Code in
such a way as specified by T-Engine Forum. Article 11. Governing Law and Language
4. The Distributor of Modification shall determine the name of the Modified Source Code subject to the rules separately established by T-Engine Forum and 1. This License Agreement shall be governed by and interpreted under the laws of Japan.
publish an appropriate notice as required by the rules on the Patch for Modification and the Modified Source Code.
2. This License Agreement is executed in both Japanese text and English text provided that the Japanese text shall govern the interpretation and performance
5. The Distributor of Modification may distribute the Modified Source Code to a third party, whether with or without payment, provided that the Distributor of of this License Agreement.
Modification shall take the necessary measures to prohibit the third party from making the re-Distribution of the Modified Source Code.
Apache License 2.0
6. Developer with the Patch for Modification. Provided, however, that the Distributor of Modification shall be obligated to confirm that the System Developer is
the Source Code User duly licensed under Article 4.1.
7. The Distributor of Modification may perform the Vicarious Execution of Patch Processing for the System Developer.
mDNSResponder_bonjour Apache License 2.0 http://www.apache.org/licenses/LICENSE-2.0
8. The System Developer shall not distribute the Modified Source Code in further modified form to any third party as a stand-alone software product.
9. The System Developer may, under the same obligation as imposed in Article 4.5, make the Embedded Product available for the End User through use of the TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
Patch for Modification distributed by the Distributor of Modification or the Derivative Works obtained through the Vicarious Execution of Patch Processing. 1. ‌Definitions.
"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
Article 6. Distribution and Registration of the Ported Source Code
"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
1. The Source Code User and the System Developer may, whether with or without charge, distribute to any third party only the following parts of the Ported
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the BZip2 License
purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii)
ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License. "Source" form shall mean the preferred form for making This program, "bzip2", the associated library "libbzip2", and all documentation, are copyright (C) 1996-2007 Julian R Seward. All rights reserved.
modifications, including but not limited to software source code, documentation source, and configuration files.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code,
generated documentation, and conversions to other media types.
bzip2-1.0.6 Bzip2 http://www.bzip.org/
"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in
or attached to the work (an example is provided in the Appendix below).
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions,
annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof. 2. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an
"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works acknowledgment in the product documentation would be appreciated but is not required.
thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf 3. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its
representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed 4. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise THIS SOFTWARE IS PROVIDED BY THE AUTHOR `ÀS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
designated in writing by the copyright owner as "Not a Contribution." "Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR
Contribution has been received by Licensor and subsequently incorporated within the Work. BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
2. ‌Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no- PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
such Derivative Works in Source or Object form. OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
3. ‌Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, Julian Seward, [email protected]
royaltyfree, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where
such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their bzip2/libbzip2 version 1.0.5 of 10 December 2007
Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a crossclaim or counterclaim in
a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted University of Illinois / NCSA Open Source License
to You under this License for that Work shall terminate as of the date such litigation is filed.
4. ‌Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object
form, provided that You meet the following conditions: Copyright (c) 1999-2007, The Board of Trustees of the University of Illinois All Rights Reserved.
(a) ‌You must give any other recipients of the Work or Derivative Works a copy of this License; and
(b) ‌You must cause any modified files to carry prominent notices stating that You changed the files; and Component Name License
(c) ‌You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the
Work, excluding those notices that do not pertain to any part of the Derivative Works; and iperf-2.0.5 University of Illinois / NCSA Open Source
(d) ‌If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution
notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: Iperf performance test
within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or,
within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational Mark Gates
purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum Ajay Tirumala
to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License.
Jim Ferguson
You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or
distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the Jon Dugan
conditions stated in this License.
Feng Qin
5. ‌Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be
Kevin Gibbs
under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the
terms of any separate license agreement you may have executed with Licensor regarding such Contributions. John Estabrook
6. ‌Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for National Laboratory for Applied Network Research
reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
National Center for Supercomputing Applications
7. ‌Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and eachContributor provides its Contributions) on an
University of Illinois at Urbana-Champaign
"AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of
TITLE, NONINFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of http://www.ncsa.uiuc.edu
using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software (Iperf) and associated documentation files (the "Software"), to deal
8. ‌Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers.
of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the
possibility of such damages. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other
materials provided with the distribution.
9. ‌Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of
support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your Neither the names of the University of Illinois, NCSA, nor the names of its contributors may be used to endorse or promote products derived from this Software
own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for without specific prior written permission. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability. BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE CONTIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
END OF TERMS AND CONDITIONS
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
APPENDIX: How to apply the Apache License to your work.
To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information.
(Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and
description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.
Copyright [yyyy] [name of copyright owner]
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License
at http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
PHP 3.01 License
The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved.
php-5.2.17 PHP 3.01 http://www.php.net/distributions
Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met:
Any changes or modifications in construction of this device which are not expressly approved by the
other materials provided with the distribution. party responsible for compliance could void the user's authority to operate the equipment.
3. The name "PHP" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, This device complies with part 15 of the FCC Rules. Operation is subject to the following two
please contact [email protected].
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
4. Products derived from this software may not be called "PHP", nor may "PHP" appear in their name, without prior written permission from [email protected].
You may indicate that your software works in conjunction with PHP by saying "Foo for PHP" instead of calling it "PHP Foo" or "phpfoo" interference received, including interference that may cause undesired operation.
5. The PHP Group may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. Once This equipment has been tested and found to comply with the limits for a Class A digital device,
covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also
choose to use such covered code under the terms of any subsequent version of the license published by the PHP Group. No one other than the PHP Group
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
has the right to modify the terms applicable to covered code created under this License. against harmful interference when the equipment is operated in a commercial environment.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes PHP software, freely available from <http://www. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
php.net/software/>". in accordance with the instruction manual, may cause harmful interference to radio communications.
THIS SOFTWARE IS PROVIDED BY THE PHP DEVELOPMENT TEAM `ÀS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT Operation of this equipment in a residential area is likely to cause harmful interference in which case
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE PHP DEVELOPMENT TEAM OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR the user will be required to correct the interference at his own expense.
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
OF SUCH DAMAGE.
This software consists of voluntary contributions made by many individuals on behalf of the PHP Group. The PHP Group can be contacted via Email at group@ Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide
php.net.
customers with more environmentally friendly products.
For more information on the PHP Group and the PHP project, please see <http://www.php.net>. PHP includes the Zend Engine, freely available at <http://www.
zend.com>. The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates
that the product satisfies the EU RoHS Directive.
zlib / libpng License
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of
this software.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
zlib-1.2.8 zlib / libpng http://zlib.net/
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Copyright (C) 1995-2010 Jean-loup Gailly and Mark Adler
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an
resources.
acknowledgment in the product documentation would be appreciated but is not required. Household users should contact either the retailer where they purchased this product, or their local government
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. office, for details of where and how they can take these items for environmentally safe recycling.
3. This notice may not be removed or altered from any source distribution. Business users should contact their supplier and check the terms and conditions of the purchase contract. This
Jean-loup Gailly Mark Adler product and its electronic accessories should not be mixed with other commercial wastes for disposal.
[email protected] [email protected]
The data format used by the zlib library is described by RFCs (Request for Comments) 1950 to 1952 in the files http://www.ietf.org/rfc/rfc1950.txt (zlib format),
rfc1951.txt (deflate format) and rfc1952.txt (gzip format).
Correct disposal of batteries in this product
Portions of this software are copyright 1996-2002 The FreeType Project (www.freetype.org). All rights reserved.
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other
household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these
substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them
through your local, free battery return system.
Head Office
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : +82.70.7147.8753 Fax : +82.31.8018.3740
www.hanwha-security.com
Hanwha Techwin America

500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax +1.201.373.0124
www.hanwha-security.com
Hanwha Techwin Europe

Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel +44.1932.57.8100 Fax +44.1932.57.8101
www.hanwha-security.eu

xnd-6080_6080v_6080r_6080rv_8080r_8080rv_xnv-6080_6080r_8080r_usermanual

Uploaded by

Copyright:

Available Formats

xnd-6080_6080v_6080r_6080rv_8080r_8080rv_xnv-6080_6080r_8080r_usermanual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

xnd-6080_6080v_6080r_6080rv_8080r_8080rv_xnv-6080_6080r_8080r_usermanual

Uploaded by

Copyright:

Available Formats

NETWORK CAMERA

 Design and specifications are subject to change without prior notice.

installation & connection 14

Used to connect with the audio and XNV-6080/

Used to connect the LAN cable with a XNV-6080/

For fixing a screw, Inserted in a hole XNV-6080/

Options (not included)

c Microphone hole Microphone is embedded.

W Zoom out (Wide)

e Zoom/Focus Control Button N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Port to connect the Wi-Fi dongle.

i Power Port Port for power terminal block.

Micro SD Memory Card

k Audio In Jack Used to connect to a microphone.

b Camera Case Housing part that covers the camera body.

W Zoom out (Wide)

e Zoom/Focus Control Button N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

Port to connect the Wi-Fi dongle.

i Power Port Port for power terminal block.

Micro SD Memory Card

k Audio In Jack Used to connect to a microphone.

b Camera Case Housing part that covers the camera body.

a Illumination Sensor Detects incoming light to control the IR LED.

b Lens Lens for the camera.

The button restores all camera settings to the factory default.

W Zoom out (Wide)

e Zoom/Focus Control Button N Focusing on a near object (Near)

F Focusing on a far object (Far)

Focus Control Press this button for automatic focus control.

f Power Port Port for power terminal block.

Port to connect the Wi-Fi dongle.

Micro SD Memory Card

Precautions before installation

could move and cause a change in the shooting range.

14_ installation & connection

Precautions before installation

●● installation & connection

Connecting waterproof power cable and LAN cable

JJ `` Use an appropriate cable bush for the LAN cable to be connected.

●● installation & connection

Connecting the alarm and audio cable Outdoor installation

monitoring direction for the camera” section. (page 18)

7. Attach the dome cover.

2. CEILING MOUNT ADAPTOR(SBP-300CM)/HANGING MOUNT(XND- `` Adjusting the monitoring direction

4. CORNER MOUNT ADAPTOR (SBP-300KM)

18_ installation & connection

●● installation & connection

Inserting a Micro SD Memory Card

[Apply] button. (Page 52)

What is a memory card?

Selecting a memory card that’s suitable for you Monitor to install

Playback performance can be affected depending on the speed of memory card.

Memory Card Components

20_ installation & connection

●● installation & connection

5. The camera angle can be adjusted through the smartphone video.

Design and specifications are subject to change without prior notice.