Scribd
Upload
67 views3 pages

Assignment Electronics 2017

ECE

Uploaded by

chalchisa.takala
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
67 views3 pages

Assignment Electronics 2017

ECE

Uploaded by

chalchisa.takala
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Individual Assignment (10%) Due Date January 3

1. Design a voltage regulator using the circuit shown below. The voltage regulator is to power a car
radio at VL = 9 V from an automobile battery whose voltage may vary between 11 and 13.6 V.
The current in the radio will vary between 0 (off) to 100 mA (full volume).

2. A load draws between 20mA and 40mA at a voltage of 20V(DC). The available dc power varies
between 100V and 140V
(a). Design a voltage regulator using the following components
• Zener diode- regulates for a zener current of 5mA to 50mA
• Resistors- any size; any number
(b). The value engineering department has found an “equivalent” zener diode that can be
purchased for 70% of the cost of your original diode. This diode regulates for a zener
current of 3mA to 42mA. What effect on your design will the substitution have? Is a
redesign necessary?

3. . For the circuit shown below. The data sheet says that 𝛽 = 100. (a) Find V𝑡ℎ & R 𝑡ℎ for the base
circuit (b) Calculate VCEQ & ICQ.
Individual Assignment (10%) Due Date January 3

4. For each transistor in the circuit given in the Figure, the parameters are: 𝛽𝑛𝑝𝑛 = 125 & 𝛽𝑝𝑛𝑝 =
80 , VBE (on) = 0.7 V. Determine I𝐵1 , I𝐶1 , V𝐶𝐸! , & V𝐸𝐶2

5. A CE amplifier is driven by a voltage source of internal resistance Rs = 800 Ω and the load
resistance RL = 1000 Ω. The h-parameters are ℎ𝑖𝑒 = 1 𝑘Ω, ℎ𝑟𝑒 = 2 × 10−4 , ℎ𝑓𝑒 = 50, and
ℎ𝑜𝑒 = 25 µ𝐴/𝑉. Compute the current gain AI, input resistance RI, voltage gain AV, and output
resistance Ro, using exact analysis and also using the approximate analysis
6. For the amplifier circuit shown in the Figure, calculate AV, Ri and Ro, given that 𝑅𝐷 = 2 𝑘𝛺,
𝑅3 = 20 𝑘𝛺, 𝑅𝑆 = 0.5 𝑘𝛺, 𝑅4 = 0.5 𝑘𝛺, 𝑅1 = 2 𝑀𝛺, 𝑅2 = 1 𝑀𝛺, 𝑔𝑚 = 2 𝑚𝑉/𝑉, and
𝑟𝑑 = 30 𝑘𝛺
Individual Assignment (10%) Due Date January 3

7. The transistor in the circuit shown below has parameters 𝛽 = 125, 𝑉𝐵𝐸(𝑜𝑛) = 0.7V, VA =
`100𝑉, 𝐶𝜋 = 24PF, 𝑎𝑛𝑑 𝐶𝜇 = 3 PF. (a) Calculate the Miller capacitance (b) Determine the upper
3dB frequency (c) Determine the small signal midband voltage gain

You might also like