w (t/m2) lx(m) Mm(N-mm/m run) Ms(N-mm/m run) Am(cm2) As(cm2)

35 0.5 8750000 7291666.666667 3.987785981 3.323154984

7291666.6666667

1900
8250

w (t/m2) lx(m) Mm(N-mm/m run) Am(mm2)

35 0.6 63000000 8.695652174

420
Bar Dia (m 12
Spacing ( 125

Ast Avaiab 9.047787 OK

M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Slab Panel Mkd. S2
Lx= Data
5.01 M
a) Ly/Lx =
b) Edge Condition:

c) Loading: 160 0
S2 UDL for DL+LL ,w =

M
d) Concrete Grade =M

9.45
e) Grade of steel= Fe
Ly=

f) Overall depth of Slab (D)=

Effective Depth of Slab = D-15-4=

From Table - 26 of IS: 456 - 2000,Moment Factors and subsequently Moments and reinforcements are obtained

Moments k=1-4.6*r/
Dir. Location Moment Factors r=M/bd^2
(T-M/M run) fck

Suppt. axs = 0.088 axs.w.lx2 = 2.06 1.55 0.71

X-Dir
Span axm = 0.066 axm.w.lx2 = 1.55 1.17 0.78
Suppt. ays = 0.047 ays.w.lx2 = 1.10 0.83 0.85
Y-Dir
Span aym = 0.035 aym.w.lx2 = 0.82 0.62 0.89

CHECK FOR SERVICABILITY

Ast Provided = 5.03 cm2/Mrun Fs= 232.35

pt Provided = 0.36 %
Referring to IS: 456 -2000;Cl.23.2.1and FIG. 4

Effective depth of Slab Reqd. (d) = 141 Effective span/26.0/Mod. Factor

Where,
Effective Span (Lx) = centre to centre dist. of support = 5.01
Mod Factor= depending on pt provided = 1.60

Therefore,
dreqd. = 120.43 mm.<Provided
OK

830729938.xls,S2 12/23/2024
 M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Panel Type 4

1.89 89 80 90

50 6 0.533
= 0.933 T/M2
25

415

160
Slab = D-15-4= 141

Moments and reinforcements are obtained as below:

Ast
pt=50*p*fc Reqd. Ast
p=1-sqrtk Ast(cm^2/m run) Reinf. Provided
k/Fe (cm2/ Prov.
Mrun)

0.15 0.47 6.57 6.89 8 Tor @ 125 c/c 4.02

0.11 0.34 4.85 5.20 8 Tor @ 100 c/c 5.03

0.08 0.24 3.38 3.69 8 Tor @ 150 c/c 3.35

0.06 0.18 2.49 2.75 8 Tor @ 175 c/c 2.87

N/mm2

830729938.xls,S2 12/23/2024
M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Slab Panel Mkd. S5
Lx= Data
3.33 M
a) Ly/Lx = 1.15
b) Edge Condition:

c) Loading:
S5 UDL for DL+LL ,w = 1.303 T/M2

M
d) Concrete Grade =M 20

3.81
e) Grade of steel= Fe 415
Ly=

f) Overall depth of Slab (D)= 100

Effective Depth of Slab = D-15-4= 81

From Table - 26 of IS: 456 - 2000,Moment Factors and subsequently Moments and reinforcements are
obtained as below:

Ast
Moments Reqd. Ast
Dir. Location Moment Factors Reinf. Provided
(T-M/M run) (cm2/ Prov.
Mrun)

Suppt. axs = 0.060 axs.w.lx2 = 0.86 5.04 8 Tor @ 100 c/c 5.03
X-Dir
Span axm = 0.045 axm.w.lx2 = 0.65 3.78 8 Tor @ 125 c/c 4.02

Suppt. ays = 0.047 ays.w.lx2 = 0.68 3.95 8 Tor @ 125 c/c 4.02
Y-Dir
Span aym = 0.035 aym.w.lx2 = 0.50 2.94 8 Tor @ 150 c/c 3.35

CHECK FOR SERVICABILITY

Ast Provided = 4.02 cm2/Mrun Fs= 226.39 N/mm2

pt Provided = 0.50 %
Referring to IS: 456 -2000;Cl.23.2.1and FIG. 4

Effective depth of Slab Reqd. (d) = 81 Effective span/24.0/Mod. Factor

Where,
Effective Span (Lx) = centre to centre dist. of support = 3.33 M
Mod Factor= depending on pt provided = 1.60

Therefore,
dreqd. = 86.59 mm.<Provided
O.K.

830729938.xls,S2 A 12/23/2024
M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Slab Panel Mkd. S3
Lx= Data
1.31 M
a) Ly/Lx = 1.13
b) Edge Condition: Two adjacent edge
discontinuous
c) Loading:
S3 UDL for DL+LL ,w = 1.303 T/M2

M
d) Concrete Grade =M 20

1.48
e) Grade of steel= Fe 415
Ly=

f) Overall depth of Slab (D)= 100

Effective Depth of Slab = D-15-4= 81

From Table - 26 of IS: 456 - 2000,Moment Factors and subsequently Moments and reinforcements are
obtained as below:

Ast
Moments Reqd. Ast
Dir. Location Moment Factors Reinf. Provided
(T-M/M run) (cm2/ Prov.
Mrun)

Suppt. axs = 0.060 axs.w.lx2 = 0.13 0.78 8 Tor @ 100 c/c 5.03
X-Dir
Span axm = 0.045 axm.w.lx2 = 0.10 0.59 8 Tor @ 125 c/c 4.02

Suppt. ays = 0.047 ays.w.lx2 = 0.11 0.61 8 Tor @ 150 c/c 3.35
Y-Dir
Span aym = 0.035 aym.w.lx2 = 0.08 0.46 8 Tor @ 200 c/c 2.51

CHECK FOR SERVICABILITY

Ast Provided = 4.02 cm2/Mrun Fs= 42.34 N/mm2

pt Provided = 0.50 %
Referring to IS: 456 -2000;Cl.23.2.1and FIG. 4

Effective depth of Slab Reqd. (d) = 81 Effective span/24.0/Mod. Factor

Where,
Effective Span (Lx) = centre to centre dist. of support = 1.31 M
Mod Factor= depending on pt provided = 1.80

Therefore,
dreqd. = 30.32 mm.<Provided
O.K.

830729938.xls,S3A 12/23/2024
M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Slab Panel Mkd. S4
Lx= Data
3.25 M
a) Ly/Lx = 1.42
b) Edge Condition:

c) Loading:
S4 UDL for DL+LL ,w = 1.230 T/M2

M
d) Concrete Grade =M 20

4.62
e) Grade of steel= Fe 415
Ly=

f) Overall depth of Slab (D)= 115

Effective Depth of Slab = D-15-4= 96

From Table - 26 of IS: 456 - 2000,Moment Factors and subsequently Moments and reinforcements are
obtained as below:

Ast
Moments Reqd. Ast
Dir. Location Moment Factors Reinf. Provided
(T-M/M run) (cm2/ Prov.
Mrun)

Suppt. axs = 0.053 axs.w.lx2 = 0.69 3.39 8 Tor @ 125 c/c 4.02
X-Dir
Span axm = 0.041 axm.w.lx2 = 0.53 2.62 8 Tor @ 175 c/c 2.87

Suppt. ays = 0.032 ays.w.lx2 = 0.42 2.05 8 Tor @ 175 c/c 2.87
Y-Dir
Span aym = 0.024 aym.w.lx2 = 0.31 1.53 8 Tor @ 200 c/c 2.51

CHECK FOR SERVICABILITY

Ast Provided = 2.87 cm2/Mrun Fs= 219.74 N/mm2

pt Provided = 0.30 %
Referring to IS: 456 -2000;Cl.23.2.1and FIG. 4

Effective depth of Slab Reqd. (d) = 96 Effective span/24.0/Mod. Factor

Where,
Effective Span (Lx) = centre to centre dist. of support = 3.25 M
Mod Factor= depending on pt provided = 1.60

Therefore,
dreqd. = 84.64 mm.<Provided
O.K.

830729938.xls,S4 12/23/2024
M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Slab Panel Mkd. S5
Lx= Data
4.66 M
a) Ly/Lx = 1.70
b) Edge Condition:

c) Loading:
S5 UDL for DL+LL ,w = 1.300 T/M2

M
d) Concrete Grade =M 20

7.90
e) Grade of steel= Fe 415
Ly=

f) Overall depth of Slab (D)= 150

Effective Depth of Slab = D-15-4= 131

From Table - 26 of IS: 456 - 2000,Moment Factors and subsequently Moments and reinforcements are
obtained as below:

Ast
Moments Reqd. Ast
Dir. Location Moment Factors Reinf. Provided
(T-M/M run) (cm2/ Prov.
Mrun)

Suppt. axs = 0.060 axs.w.lx2 = 1.69 6.10 10 Tor @ 200 c/c 0.39
X-Dir
Span axm = 0.045 axm.w.lx2 = 1.27 4.58 8 Tor @ 200 c/c 2.51

Suppt. ays = 0.032 ays.w.lx2 = 0.90 3.25 8 Tor @ 250 c/c 2.01
Y-Dir
Span aym = 0.024 aym.w.lx2 = 0.68 2.44 8 Tor @ 200 c/c 2.51

CHECK FOR SERVICABILITY

Ast Provided = 2.51 cm2/Mrun Fs= 527.90 N/mm2

pt Provided = 0.19 %
Referring to IS: 456 -2000;Cl.23.2.1and FIG. 4

Effective depth of Slab Reqd. (d) = 131 Effective span/24.0/Mod. Factor

Where,
Effective Span (Lx) = centre to centre dist. of support = 4.66 M
Mod Factor= depending on pt provided =

Therefore,
dreqd. = #VALUE! mm.<Provided
O.K.

830729938.xls,S5 12/23/2024
PANEL LIST
1 Column1 Column1 Y
2 Y Y Column1
3 N N Y
4 N N
5
6
7 Y
8 N
9
2
3 Check Box 3
4
Y
5

Column1
Y Y Column1
N N Y
N

W
W

One Edge Dis

One Edge Dis

One Edge Dis
Two Adjacent Edge

1
3

Column1
1

Column1
PANEL
a
b
c
d
 0.028
0.037
Y
 Effective Depth
Panel Type Lx (mm) Ly (mm) Overall Depth (mm) (mm) Drop (mm) Floor Finish (mm) Plaster (mm) Loading (t/m^2) Concrete (M)
 One Way or k=1- pt=50*p*f Ast(cm^2/
Steel (Fe) Lx/Ly Two Way Coeff. Moment r=M/bd^2 4.6*r/fck p=1-sqrtk ck/Fe m run) Fs
axs Mx Supp.
axm Mx Span.
ays My Supp.
aym My Span.
Depth Mod. Depth
Factor Factor. dreqd. dprov. Checking
 INPUT MATERIAL
INPUT PROPERTIES

Panel Type (As per Two Adjacent Edges

IS 456) Discontinuous Concrete (M) 25

Lx (m) 5.01 Steel (Fe) 415

Click Here to get Output Data
Ly (m) 9.450

Load (t/m^2) 0.933

OUTPUT
OR

Dir. Location Ast Reqd. (cm2/Mrun) Ast Shcedule Ast Prov.

Put Load intensity in
t/m^2 or Put the
following details N
Depth of Slab(mm) 160 Suppt. 06.57 8 Tor @ 125 c/c 04.02
X-Dir
Span 04.85 8 Tor @ 100 c/c 05.03
Drop(mm) 0 Suppt. 03.38 8 Tor @ 150 c/c 03.35
Y-Dir
Span 02.49 8 Tor @ 175 c/c 02.87
Floor Finish(mm) 50 Depth Checking
Eff. Depth Required 120.43 Click Here to get Output Data for One Way Slab
Plaster(mm) 6 Eff. Depth Provided 141.00 OK

Message The Slab Has Been Designed as Two Way Slab

Y
N
Interior Panels
One Short Edge Discontinuous
One Long Edge Discontinuous
Two Adjacent Edges Discontinuous
Two Short Edge Discontinuous
Two Long Edge Discontinuous
One Long Edge Continuous
One Short Edge Continuous
Four Edges Discontinuous
utput Data for One Way Slab
 NEGATIVE
01.00 01.10 01.20 01.30 01.40 01.50 01.75 02.00 ALFAY
1 0.032 0.037 0.043 0.047 0.051 0.053 0.06 0.065 0.032
2 0.037 0.043 0.048 0.051 0.055 0.057 0.064 0.068 0.037
3 0.037 0.044 0.052 0.057 0.063 0.067 0.077 0.085 0.037
4 0.047 0.053 0.06 0.065 0.071 0.075 0.084 0.091 0.047
5 0.045 0.049 0.052 0.056 0.059 0.06 0.065 0.069 0
6 0 0 0 0 0 0 0 0 0.045
7 0.057 0.064 0.071 0.076 0.08 0.084 0.091 0.097 0
8 0 0 0 0 0 0 0 0 0.057
9 0 0 0 0 0 0 0 0 0

POSITIVE
01.00 01.10 01.20 01.30 01.40 01.50 01.75 02.00 ALFAX
1 0.024 0.028 0.032 0.036 0.039 0.041 0.045 0.049 0.024
2 0.028 0.032 0.036 0.039 0.041 0.044 0.048 0.052 0.028
3 0.028 0.033 0.039 0.044 0.047 0.051 0.059 0.065 0.028
4 0.035 0.04 0.045 0.049 0.053 0.056 0.063 0.069 0.035
5 0.035 0.037 0.04 0.043 0.044 0.045 0.049 0.052 0.035
6 0.035 0.043 0.051 0.057 0.063 0.068 0.08 0.088 0.035
7 0.043 0.048 0.053 0.057 0.06 0.064 0.069 0.073 0.043
8 0.043 0.051 0.059 0.065 0.071 0.076 0.087 0.096 0.043
9 0.056 0.064 0.072 0.079 0.085 0.089 0.1 0.107 0.056

120 125 130 135 140 145 150 155 160

0.1 2 2
0.2 2 2
0.3 2 2
0.4 2 2
0.5 2 1.98
0.6 2 1.8
0.7 1.9 1.64
0.8 1.8 1.56
0.9 1.7
1 1.6
1.1 1.55
1.2 1.5
1.3 1.45
1.4 1.4
1.5 1.285
1.6 1.275
1.7 1.26
1.8 1.25
1.9 1.225
2 1.215
2.1 1.205
2.2 1.2
2.3 1.195
2.4 1.18
2.5 1.16
2.6 1.14
2.7 1.135
2.8 1.125
2.9 1.1
3 1.095
165 170 175 180 185 190 195 200 205 210
215 220 225 230 235 240 245 250 255 260
265 270 275 280 285 290
M.N.Consultants(P) Ltd. HSG 010 (Block-A) 1st Floor

TYPICAL DESIGN OF SLAB

Slab Panel Mkd. S5
Lx= Data
4.00 M
a) Ly/Lx = 1.53
b) Edge Condition:

c) Loading:
S5 UDL for DL+LL ,w = 0.646 T/M2

M
d) Concrete Grade =M 20

6.12
e) Grade of steel= Fe 415
Ly=

f) Overall depth of Slab (D)= 125

Effective Depth of Slab = D-15-4= 106

From Table - 26 of IS: 456 - 2000,Moment Factors and subsequently Moments and reinforcements are
obtained as below:

Ast
Moments Reqd. Ast
Dir. Location Moment Factors Reinf. Provided
(T-M/M run) (cm2/ Prov.
Mrun)

Suppt. axs = 0.080 axs.w.lx2 = 0.83 3.68 8 Tor @ 200 c/c 2.51
X-Dir
Span axm = 0.058 axm.w.lx2 = 0.60 2.67 8 Tor @ 200 c/c 2.51

Suppt. ay s = ays.w.lx2 = #VALUE! ### 8 Tor @ 250 c/c 2.01

Y-Dir
Span aym = 0.024 aym.w.lx2 = 0.25 1.11 8 Tor @ 200 c/c 2.51

CHECK FOR SERVICABILITY

Ast Provided = 2.51 cm2/Mrun Fs= 308.16 N/mm2

pt Provided = 0.24 %
Referring to IS: 456 -2000;Cl.23.2.1and FIG. 4

Effective depth of Slab Reqd. (d) = 106 Effective span/24.0/Mod. Factor

Where,
Effective Span (Lx) = centre to centre dist. of support = 4.00 M
Mod Factor= depending on pt provided =

Therefore,
dreqd. = #VALUE! mm.<Provided
O.K.

830729938.xls,S7 12/23/2024
Story Point Load FX FY FZ MX MY MZ
BASE 319 FDN 0.08 -0.93 83.69 0.951 0.092 0
BASE 320 FDN -0.09 -0.93 83.78 0.946 -0.102 0
BASE 321 FDN 0.26 1.07 74.7 -1.314 0.3 0
BASE 322 FDN -0.27 1.06 74.74 -1.308 -0.311 0
BASE 332 FDN -0.31 0.05 64.87 -0.22 -0.359 0
BASE 333 FDN 0.34 0.05 65.41 -0.215 0.381 0
BASE 334 FDN -0.21 -0.16 37.63 0.024 -0.251 0
BASE 335 FDN 0.2 -0.16 37.79 0.028 0.224 0
522.61