FOREWORD

This Supplementary Service Manual has been prepared to introduce new service and data for the
YZF-R6 (L) 2000. For complete service information procedures it is necessary to use this Supplemen-
tary Service Manual together with the following manual.

YZF-R6 ’99 SERVICE MANUAL: 5EB1-AE1

YZF-R6 (L) 2000

SUPPLEMENTARY
SERVICE MANUAL
 1999 by Yamaha Motor Co., Ltd.
First Edition, August 1999
Any reproduction or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd. is expressly
prohibited.
EB001000

NOTICE
This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manu-
al, so it is assumed that anyone who uses this book to perform maintenance and repairs on Yamaha
motorcycles has a basic understanding of the mechanical ideas and the procedures of motorcycles
repair.
Repairs attempted by anyone without this knowledge are likely to render the motorcycles unfit for use.
Yamaha Motor Company, Ltd. is continually striving to improve all its models. Modifications and signifi-
cant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers and
will appear in future editions of this manual where applicable.
NOTE:
Designs and specifications are subject to change without notice.

IMPORTANT INFORMATION
Particularly important information is distinguished in this manual by the following.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR

SAFETY IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to

WARNING
the motorcycle operator, a bystander or a person inspecting or repairing the
motorcycle.

CAUTION: A CAUTION indicates special precautions that must be taken to avoid damage
to the motorcycle.

NOTE: A NOTE provides key information to make procedures easier or clearer.

YP002000

HOW TO USE THIS MANUAL

This manual is intended as a handy, easy-to-read reference book for the mechanic. Comprehensive
explanations of all installation, removal, disassembly, assembly, repair and inspection procedures are
laid out with the individual steps in sequential order.
1 The manual is divided into chapters. An abbreviation and symbol in the upper right corner of each
page indicate the current chapter. Refer to “SYMBOLS” on the following page.
2 Each chapter is divided into sections. The current section title is shown at the top of each page,
except in Chapter 3 (“Periodic Inspections and Adjustments”), where the sub-section title (-s) appear.
(In Chapter 3, “Periodic Inspections and Adjustments”, the sub-section title appears at the top of each
page, instead of the section title.)
3 Sub-section titles appear in smaller print than the section title.
4 To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each
removal and disassembly section.
5 Numbers are given in the order of the jobs in the exploded diagram. A circled number indicates a
disassembly step.
6 Symbols indicate parts to be lubricated or replaced (see “SYMBOLS”).
7 A job instruction chart accompanies the exploded diagram, providing the order of jobs, names of
parts, notes in jobs, etc.
8 Jobs requiring more information (such as special tools and technical data) are described sequen-
tial0ly.

2 1 4 3

5 8

7
 EB003000

1 2 SYMBOLS
The following symbols are not relevant to every
GEN
SPEC vehicle.
INFO Symbols 1 to 9 indicate the subject of each
chapter.
3 4 1 General information
CHK 2 Specifications
ADJ ENG 3 Periodic checks and adjustment
4 Engine
5 6 5 Cooling system
6 Carburetor(-s)
7 Chassis
COOL CARB 8 Electrical system
9 Troubleshooting
7 8

CHAS ELEC
Symbols 10 to 17 indicate the following.
9 10
10 Serviceable with engine mounted
TRBL 11 Filling fluid
12 Lubricant
SHTG 13 Special tool
11 12 14 Tightening torque
15 Wear limit, clearance
16 Engine speed
17 Electrical data

13 14

15 16 17

Symbols 18 to 23 in the exploded diagrams indi-

18 19 20
cate the types of lubricants and lubrication
points.
18 Apply engine oil
19 Apply gear oil
21 22 23 20 Apply molybdenum disulfide oil
21 Apply wheel bearing grease
22 Apply lightweight lithium-soap base grease
23 Apply molybdenum disulfide grease

24 25
Symbols 24 to 25 in the exploded diagrams indi-
cate the following:
24 Apply locking agent (LOCTITE)
25 Use new one
 CONTENTS
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ENGINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
TIGHTENING TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CHASSIS TIGHTENING TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . 3
CABLE ROUTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PERIODIC CHECKS AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . 12

CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ADJUSTING THE CLUTCH CABLE FREE PLAY . . . . . . . . . . . . 12

OVERHAULING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DRIVE SPROCKET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
INSTALLING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PICKUP COIL AND PICKUP ROTOR . . . . . . . . . . . . . . . . . . . . . . . . . . 16
INSTALLING THE PICKUP COIL ROTOR . . . . . . . . . . . . . . . . . . 16

CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
REAR SHOCK ABSORBER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . 18
REMOVING THE REAR SHOCK ABSORBER ASSEMBLY . . . 19
SWINGARM AND DRIVE CHAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
INSTALLING THE SWINGARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

YZF-R6 (L) 2000 WIRING DIAGRAM

 GEN
SPECIAL TOOLS INFO
EB104000

SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly.
Use only the appropriate special tools as this will help prevent damage caused by the use of inappropri-
ate tools or improvised techniques.
When placing an order, refer to the list provided below to avoid any mistakes.

Tool No. Tool name/Function Illustration

Pivot shaft Pivot shaft wrench
wrench Adapter
90890-01471
Adapter This tool is used to loosen or tighten the pivot
90890-01476 adjust bolt and engine mount adjust bolt.

–1–
ENGINE SPECIFICATIONS/ELECTRICAL SPECIFICATIONS SPEC

ENGINE SPECIFICATIONS
Item Standard Limit
Pistons
Oil ring

Dimensions (B T) 1.5 2.0 mm SSS

End gap (installed) 0.10 X 0.35 mm SSS
Crankshaft
Crankshaft-journal-to-crankshaft- 0.028 X 0.052 mm SSS
journal-bearing clearance
Carburetors
ID mark 5EB1 SSS
Jet needle #1, 4: N7RA #2, 3: N7SA SSS
Pilot screw turns out 1-1/2 Y 2 SSS

ELECTRICAL SPECIFICATIONS
Item Standard Limit
Ignition system
Ignition timing 10_ BTDC at 1300 r/min SSS
Ignition coils
Primary coil resistance 0.204 X 0.276 Ω SSS
Secondary coil resistance 8.5 X 11.5 Ω SSS
Oil level switch model (manufacturer) 5EB (DENSO) SSS
Fuel pump relay model (manufacturer) G8R-30Y-M (OMRON) SSS
Resistance 162 X 198 Ω

–2–
 TIGHTENING TORQUES SPEC
CHASSIS TIGHTENING TORQUES

Tightening
Item Thread size torque Remarks
Nm mSkg
Engine mounting adjusting bolts 7 0.7
Rear shock absorber and frame M10 40 4.0
Pivot shaft adjust bolt 5 0.5

–3–
 CABLE ROUTING SPEC
EB206000

CABLE ROUTING
1 Throttle cables A Install the headlight relays onto the headlight housing bridge.
2 Clutch cable B Route the headlight lead through the plastic guide.
3 Left handlebar switch lead C Route the headlight lead through the headlight bracket right side, and
4 Starter cable connect relay.
5 Main switch lead D Don’t kink.
6 Front brake hose E Put coupler into stay.
7 Right handlebar switch lead F Make sure the connector is out off the bottom end of front cowling.
G Route the right handlebar switch lead in front of the front fork inner tube.
H Route the throttle cables between the brake hose and right handlebar
switch lead.
I Route the wire harness through under the left handlebar switch lead
and starter cable.
J Fasten the left handlebar switch lead to the front fork with a plastic lock-
ing tie and cut the end of locking tie.
K Fasten the throttle cables and starter cable with a band.

–4–
 CABLE ROUTING SPEC
L Locate the end of band to for ward.
Route the horn lead outside the throttle cables and
fasten it to the under bracket with a plastic locking
tie. Cut the end of locking tie.
And then, route the horn lead under the brake hose
and clamp it to the under cover.

–5–
 CABLE ROUTING SPEC
1 Fuel pump lead F Fasten the rear brake switch lead to the footrest
2 Pickup coil lead bracket with a plastic locking tie and cut the end of
3 Thermo switch locking tie.
4 Clutch cable G Fasten the fuel pump lead and rear brake switch
5 Rear brake switch lead lead with a plastic band on the fuel pump bracket.

A Route the ignition coil lead and thermo switch lead

over the heat protector plate.
B Route the clutch cable through the guide on the
frame.
C Position the face of steel clip up ward.
D Route the coolant hoses (3 hoses) under the heat
protector plate.
E Fasten the clutch cable to the coolant hose protec-
tor with a plastic band.

–6–
 CABLE ROUTING SPEC
1 AC magneto lead C Don’t touch the wireharness with the throttle cable
2 Reservoir tank breather hose pully. Route the wire harness under the radiator
3 Sidestand switch lead hose.
4 Oil level switch lead D Route the fuel tank breather hose and fuel tank
5 Speed sensor lead drain hose between reservor tank breather hose
6 Fuel pump lead and wireharness.
7 Neutral switch lead E Route the wireharness through the slite of rear
fender.
A Route the throttle cable through inside of the radia- F Route the seat lock cable outside of the wire-
tor bracket and outside of the wireharness. harness.
B Fasten the wireharness, radiator hose and fan mo- G Route the rear turn signal light leads (left and right)
tor lead with a plastic band. through the hole of rear fender.
Locate the end of band to inside. H Route the fuel tank drain hose and the fuel tank
Push the radiator fan motor lead connector be- breather hose behind the curve of the under
tween radiator hose and wireharness. cawl. 7

–7–
 CABLE ROUTING SPEC
I Route the fuel tank drain hose and the fuel tank
breather hose through the reservor tank holder
from its outside to inside. Don’t kink.
J Route the fuel tank drain hose and fuel tank breath-
er hose through the holder of the hook and the side-
stand. Don’t kink.
K When the sidestand is used.
L The bottom end of the drain hose comes here.
M Fasten the sidestand switch lead and oil level sen-
sor lead with a band.
N Route the reservoir tank breather hose, oil level
switch lead and sidestand switch lead through the
holder.
O Route the starter cable between wireharness and
left handlebar switch lead.

–8–
 CABLE ROUTING SPEC
1 Throttle cable 18 Fuel sender connector
2 Right handlebar switch lead 19 Coolant reservoir tank cap
3 Thermo unit lead 20 Crankcase breather hose
4 Reservoir tank breather hose 21 Heat protector
5 Carburetor idle adjusting cable 22 Radiator fan motor lead
6 Pickup coil connector 23 Clutch cable
7 Neutral switch connector 24 Left handlebar switch lead
8 Rear brake switch connector 25 Starter cable
9 Right handlebar switch connectors 26 Main switch lead
10 Throttle position sensor connector
11 Main switch connectors A Route the clutch cable through the guide.
12 Left handlebar switch connectors B Fasten the handlebar switch leads (left and right)
13 Neutral switch lead and main switch lead with a band.
14 Fuel pump connector Locate the end of band to inside.
15 Rear brake switch lead C Route the ignition coil lead and handlebar switch
16 Starter motor lead leads (left and right) over the heat protector.
17 Battery negative (–) lead D Route the radiator hoses under the heat protector.

–9–
 CABLE ROUTING SPEC
E Fasten the wireharness pickup coil lead handlebar L Position the rear turn signal light connectors (left
switch lead (left and right) main switch lead TPS and right) and taillight connector between the rear
lead with a band. fender and taillight bracket.
F To the carburetor. M Install the seatlock cable to the frame bracket with
G Insert the projection of the band to the hole of the protector side.
frame and fasten the wireharness, neutral switch N Fasten the lead through under the wireharness and
lead handlebar switch leads (left and right), main oil relay lead.
switch lead, TPS lead, rear brake switch lead and O Fasten the alarm leads wireharness oil relay lead
pickup coil lead with them. and ground lead with a band.
H Neutral switch lead can be put either over or under P Fasten the starter relay lead and battery negative
the wireharness and starter motor. (–) lead to the wireharness with a band. Don’t put
I Route the starter motor lead under the wireharness the upper end of the band between the seat rail and
and battery negative (–) lead. the seat bottom.
J Fasten the starter motor lead to the rear fender with Q From the engine.
a band. R To the fuel filter.
K Fasten the battery positive (+) lead and starter mo- S Fasten the battery negative (–) lead and wirehar-
tor lead with a band. ness with a band.

–10–
 CABLE ROUTING SPEC
T Insert the projection of the band (wireharness) into A’ Insert the projection of the band to the hole of the
the hole of the frame. frame and faster the starter cable and wireharness.
U 1: Speed sensor. Locate the end of band to left outside.
2: AC magneto connector. B’ To headlight lead.
3: Sidestand switch connector. C’ Route the starter cable over the heat protector.
4: Oil level switch connector. D’ Route the temperature lead upper the heat protec-
5: Meter ground lead. tor.
V Fasten the leads (above 1 X 5) and starter motor E’ Route the reservoir tank breather hose upper the
lead with a band. heat protector.
W Route the fuel tank drain hose and fuel tank breath- F’ The fuel tank drain hose, temperature sender lead
er hose outside of the wireharness and air chamber reservoir tank breather hose must be located over
hose. the groove.
X The starter cable must not be out off the guide G’ Reservoir tank breather hose above the wire-
groove of the cover. harness.
Y Insert the starter cable to the guide.
Z To radiator fan motor.

–11–
 CHK
ADJUSTING THE CLUTCH CABLE FREE PLAY ADJ
CHASSIS
EB303100

ADJUSTING THE CLUTCH CABLE FREE

PLAY
1. Measure:
S clutch cable free play a
Out of specification ! Adjust.

Clutch cable free play (at the end

of the clutch lever)
10 X 15 mm

2. Adjust:
S clutch cable free play

Handlebar side
a. Turn the adjusting bolt 1 in direction a or b
until the specified clutch cable free play is ob-
tained.
Clutch cable free play is
Direction a
increased.
Clutch cable free play is
Direction b
decreased.
NOTE:
If the specified clutch cable free play cannot be
obtained on the handlebar side of the cable, use
the adjusting nut on the engine side.

Engine side
a. Loosen the locknut 2 .
b. Turn the adjusting nut 3 in direction c or d
until the specified clutch cable free play is ob-
tained.
Clutch cable free play is
Direction c
increased.
Clutch cable free play is
Direction d
decreased.
NOTE:
When the align mark of the cover and the lever
are mated the gap.
Should be the maximum (78.3 mm).

a 70.0 Y 78.3 mm
c. Tighten the locknut.

–12–
 ENGINE ENG
EAS00190

OVERHAULING THE ENGINE

ENGINE
DRIVE SPROCKET

10 Nm (1.0 mSkg)

70 Nm (7.0 mSkg)

Order Job/Part Q’ty Remarks

Removing the drive sprocket Remove the parts in the order listed.
Reserve tank Refer to “CHANGING THE COOLANT”
1 Locknut 2
2 Shift rod 1
3 Shift arm 1
4 Drive sprocket cover 1
5 Nut 1
6 Lock washer 1
7 Drive sprocket 1
For installation reverse the remove
procedure.

–13–
 ENGINE ENG

ENGINE

24 Nm (2.4 mSkg)

45 Nm (4.5 mSkg) 55 Nm (5.5 mSkg)

38 Nm (3.8 mSkg)

13 Nm (1.3 mSkg)
55 Nm (5.5 mSkg)
24 Nm (2.4 mSkg)

7 Nm (0.7 mSkg)

Order Job/Part Q’ty Remarks

Removing the engine Remove the parts in the order listed.
NOTE:
Place a suitable stand under the frame and
engine.

1 Pinch bolts 4
2 Button head bolts 2
3 Collars 2
4 Front mounting bolts 2 Refer to “INSTALLING THE ENGINE”.
5 Collars 2
6 Rear mounting bolts 2
7 Engine mounting adjust bolts 2
NOTE:
Use the pivot shaft wrench to loosen the
engine mounting adjust bolt.

For installation, reverse the removal

procedure.
–14–
 ENGINE ENG
EAS00192

INSTALLING THE ENGINE

1. Install:
S engine mounting adjust bolts 1
S rear mounting bolts 2
S self-locking nuts 3
S collars 4
S front mounting bolts 5
S collars 6
S button head bolts 7
S pinch bolts 8
NOTE:
S Lubricate the rear mounting bolt threads with
lithium soap base grease.
S Do not fully tighten the nuts and bolts.

2. Tighten:
S self-locking nut 47 Nm (4.7mSkg)
S front mounting bolts 55 Nm (5.5 mSkg)
S button head bolt 39 Nm (3.9 mSkg)
S pinch bolt M8 24 Nm (2.4 mSkg)
M6 13 Nm (1.3 mSkg)
S engine mounting adjusting bolts
7 Nm (0.7 mSkg)
NOTE:
Use the pivot shaft wrench 1 and pivot shaft
wrench adapter 2 to tighten the engine mount-
ing adjust bolt.

Pivot shaft wrench

90890-01471
Pivot shaft wrench adapter
90890-01476

3. Install:
S drive sprocket 70Nm (7.0 mSkg)
4. Install:
S drive sprocket cover 10 Nm (1.0 mSkg)
NOTE:
Refer to “CABLE ROUTING” in chapter 2.

5. Install:
S shift arm 1 10 Nm (1.0 mSkg)
NOTE:
Align the punch mark a in the shift shaft with
the slot in the shift arm.

–15–
PICKUP COIL AND PICKUP ROTOR ENG
INSTALLING THE PICKUP COIL ROTOR
1. Install:
S pickup coil rotor 1
S plain washer
S pickup coil rotor bolt
NOTE:
When installing the pickup coil rotor, align the
pin 2 in the crankshaft sprocket with the groove
a in the pickup coil rotor.

2. Tighten:
S pickup coil rotor bolt 1
35 Nm (3.5 mSkg)
NOTE:
While holding the generator rotor 2 with the
sheave holder 3 , tighten the pickup coil rotor
bolt.

Sheave holder
90890-01701

3. Apply:
S sealant
(onto the pickup coil lead grommet)

Yamaha bond No.1215

90890-85505

4. Install:
S pickup coil cover
NOTE:
S When installing the pickup coil cover, align the
timing chain guide (intake side) pin 1 of the
with the hole 2 in the pickup coil cover.
S Tighten the pickup coil cover bolts in stages
and in a crisscross pattern.

–16–
PICKUP COIL AND PICKUP ROTOR ENG
5. Install
S Clutch cable holder
S Clutch cable
Refer to “ADJUSTING THE CLUTCH CABLE
FREE PLAY” in chapter 3.

–17–
 REAR SHOCK ABSORBER ASSEMBLY CHAS
EAS00685

REAR SHOCK ABSORBER ASSEMBLY

40 Nm (4.0 mSkg)

40 Nm (4.0 mSkg)

40 Nm (4.0 mSkg)

Order Job/Part Q’ty Remarks

Removing the rear shock absorber Remove the parts in the order listed.
assembly
Rear wheel Refer to “REMOVING THE REAR WHEEL”.
1 Self-locking nut/bolt 1/1
2 Self-locking nut/bolt 1/1
3 Self-locking nut/bolt/coller 1/1/1 Refer to “REMOVING THE REAR
4 Self-locking nut/bolt 1/1 SHOCK ABSORBER ASSEMBLY”.
5 Self-locking nut/bolt 1/1
6 Rear shock absorber assembly 1
7 Coller/oil seal/bearing 1/2/1
8 Relay arm 2
9 Coller/oil seal/bearing 1/2/1
10 Connecting arm 1
11 Coller/oil seal/bearing 1/2/1
For installation, reverse the removal
procedure.

–18–
REAR SHOCK ABSORBER ASSEMBLY CHAS
EAS00694

REMOVING THE REAR SHOCK ABSORBER

ASSEMBLY
1. Stand the motorcycle on a level surface.
WARNING
Securely support the motorcycle so that
there is no danger of it falling over.

NOTE:
Place the motorcycle on a suitable stand so that
the rear wheel is elevated.

2. Remove:
S rear wheel
S rear shock absorber assembly lower bolt 1
S relay-arm-to-swingarm bolt 2
NOTE:
While removing the rear shock absorber as-
sembly lower bolt, hold the swingarm so that it
does not drop down.

3. Remove:
S rear shock absorber assembly upper bolt 1
S rear shock absorber assembly
NOTE:
Raise the swingarm and then remove the rear
shock absorber assembly from between the
swingarm.

–19–
 SWINGARM AND DRIVE CHAIN CHAS
EAS00700

SWINGARM AND DRIVE CHAIN

95 Nm (9.5 mSkg) 5 Nm (0.5 mSkg)

6 Nm (0.6 mSkg)

6 Nm (0.6 mSkg)

Order Job/Part Q’ty Remarks

Removing the swingarm and drive Remove the parts in the order listed.
chain
Drive sprocket Refer to “ENGINE” in chapter 4.
Rear wheel Refer to “REAR WHEEL, BRAKE DISC,
AND REAR WHEEL SPROCKET”.
Rear shock absorber assembly Refer to “REAR SHOCK ABSORBER
ASSEMBLY”.
1 Adjusting bolt/locknut 2/2
2 Drive chain guard 1
3 Rear fender 1
4 Flap 1
5 Pivot shaft nut/washer 1/1
6 Pivot shaft 1
7 Swingarm 1

–20–
 SWINGARM AND DRIVE CHAIN CHAS

95 Nm (9.5 mSkg) 5 Nm (0.5 mSkg)

6 Nm (0.6 mSkg)

6 Nm (0.6 mSkg)

Order Job/Part Q’ty Remarks

8 Pivot shaft adjust bolt 2 Refer to “REMOVING/INSTALLING THE
SWINGARM”.
9 Drive chain 1
10 Dust cover 1
11 Oil seal 1
12 Bush 1
13 Shim 1
14 Drive chain guide 1
15 Bush 1
16 Left bearing 1
17 Right bearing 1
For installation, reverse the removal
procedure.

–21–
SWINGARM AND DRIVE CHAIN CHAS
EAS00711

INSTALLING THE SWINGARM

1. Lubricate:
S bearings
S spacers
S dust covers
S pivot shaft

Recommended lubricant
Lithium soap base grease

2. Install:
S swingarm
S pivot shaft
S washer
S pivot shaft adjust bolt 1
5 Nm (0.5 mSkg)
S pivot shaft nut 95 Nm (9.5 mSkg)
NOTE:
Use the pivot shaft wrench 2 and pivot shaft
wrench adapter 3 to tighten the pivot adjust
bolt.

Pivot shaft wrench:

90890-01471
Pivot shaft wrench adapter
90890-01476

3. Install:
S rear shock absorber assembly
S rear wheel
Refer to “REAR SHOCK ABSORBER AS-
SEMBLY” and “REAR WHEEL”.
4. Adjust:
S drive chain slack
Refer to “ADJUSTING THE DRIVE CHAIN
SLACK” in chapter 3.

Drive chain slack

40 X 50 mm

–22–
YZF-R6 (L) 2000 WIRING DIAGRAM (for EUR) 1 Main switch
2 Fuse (back up)
3 Rectifier / Regulator
4 AC magneto
5 Battery
6 Fuse (main)
7 Starter relay
8 Starter motor
9 Starting circuit cut-off relay
10 Sidestand switch
11 Fuel pump
12 Throttle position sensor
13 Pickup coil
14 CDI unit
15 Ignition coil #1
16 Ignition coil #2
17 Ignition coil #3
18 Ignition coil #4
19 Spark plug
20 Meter assembly
21 Fuel level indicator light
22 Oil level / coolant temperature warning light
23 Neutral indicator light
24 Tachometer
25 Combination meter
26 Hi beam indicator light
27 Turn signal indicator light
28 Illumination light
29. Speed sensor
30 Neutral switch
31 Thermo unit
32 Fuel sender
33 Right handlebar switch
34 Front brake light switch
35 Light switch
36 Engine stop switch
37 Start switch
38 Left handlebar switch
39 Pass switch
40 Dimmer switch
41 Horn switch
42 Clutch switch
43 Turn signal switch
44 Horn
45 Flasher relay
46 Headlight relay (Hi)
47 Headlight relay (Lo)
48 Headlight
49 Auxiliary light
50 Front turn signal light (left)
51 Front turn signal light (right)
52 Rear turn signal light (left)
53 Rear turn signal light (right)
54 Tail / brake light
COLOR CODE 55 Oil level relay
B ..... Black O .... Orange B/ Y . . . Black/ Yellow Gy/ B . Gray / Black R/ L . . . Red/ Blue 56 Oil level switch
Br . . . . Brown P ..... Pink Br/ B . . Brown/ Black L/B . . . Blue/ Black R/ W . . Red/ White 57 Rear brake light switch
Ch . . . Chocolate R..... Red Br/ L . . Brown/ Blue L/R . . . Blue/ Red R/ Y . . . Red/ Yellow 58 Fuse (ignition)
59 Alarm
Dg . . . Dark green Sb . . . . Sky blue Br/ R . . Brown/ Red L/W . . Blue/ White Sb/ W . Sky blue / White
60 Fuse (signaling system)
G .... Green W .... White Br/ W . Brown/ White L/Y . . . Blue/ Yellow W/ G . . White/ Green
61 Fuse (headlight)
Gy . . . Gray Y ..... Yellow G/R . . Green / Red O/B . . Orange / Black W/ R . . White/ Red
62 Fuse (radiator fan motor)
L ..... Blue B/ L . . . Black/ Blue G/W . . Green / White R/ B . . . Red/ Black W/ Y . . White/ Yellow
63 Thermo switch
Lg . . . . Blue green B/ R . . . Black/ Red G/Y . . Green / Yellow R/ G . . Red/ Green Y/ B . . . Yellow/ Black
64 Radiator fan motor
YZF-R6 (L) 2000 WIRING DIAGRAM (for AUS)
1 Main switch
2 Fuse (back up)
3 Rectifier / Regulator
4 AC magneto
5 Battery
6 Fuse (main)
7 Starter relay
8 Starter motor
9 Starting circuit cut-off relay
10 Sidestand switch
11 Fuel pump
12 Throttle position sensor
13 Pickup coil
14 CDI unit
15 Ignition coil #1
16 Ignition coil #2
17 Ignition coil #3
18 Ignition coil #4
19 Spark plug
20 Meter assembly
21 Fuel level indicator light
22 Oil level / coolant temperature warning light
23 Neutral indicator light
24 Tachometer
25 Combination meter
26 Hi beam indicator light
27 Turn signal indicator light
28 Illumination light
29. Speed sensor
30 Neutral switch
31 Thermo unit
32 Fuel sender
33 Right handlebar switch
34 Front brake light switch
36 Engine stop switch
37 Start switch
38 Left handlebar switch
39 Pass switch
40 Dimmer switch
41 Horn switch
42 Clutch switch
43 Turn signal switch
44 Horn
45 Flasher relay
46 Headlight relay (Hi)
47 Headlight relay (Lo)
48 Headlight
50 Front turn signal light (left)
51 Front turn signal light (right)
52 Rear turn signal light (left)
53 Rear turn signal light (right)
54 Tail / brake light
55 Oil level relay
56 Oil level switch
COLOR CODE 57 Rear brake light switch
B ..... Black O .... Orange B/ Y . . . Black/ Yellow Gy/ B . Gray / Black R/ L . . . Red/ Blue 58 Fuse (ignition)
Br . . . . Brown P ..... Pink Br/ B . . Brown/ Black L/B . . . Blue/ Black R/ W . . Red/ White 60 Fuse (signaling system)
Ch . . . Chocolate R..... Red Br/ L . . Brown/ Blue L/R . . . Blue/ Red R/ Y . . . Red/ Yellow 61 Fuse (headlight)
Dg . . . Dark green Sb . . . . Sky blue Br/ R . . Brown/ Red L/W . . Blue/ White Sb/ W . Sky blue / White 62 Fuse (radiator fan motor)
G .... Green W .... White Br/ W . Brown/ White L/Y . . . Blue/ Yellow W/ G . . White/ Green 63 Thermo switch
Gy . . . Gray Y ..... Yellow G/R . . Green / Red O/B . . Orange / Black W/ R . . White/ Red 64 Radiator fan motor
L ..... Blue B/ L . . . Black/ Blue G/W . . Green / White R/ B . . . Red/ Black W/ Y . . White/ Yellow
Lg . . . . Blue green B/ R . . . Black/ Red G/Y . . Green / Yellow R/ G . . Red/ Green Y/ B . . . Yellow/ Black