PID Tutorial

Introduction
The three-term controller
The characteristics of P, I, and D controllers
Example Problem

Open-loop step response

Proportional control
Proportional-Derivative control
Proportional-Integral control
Proportional-Integral-Derivative control
General tips for designing a PID controller

Key Matlab Commands used in this tutorial are: step cloop

Note: Matlab commands from the control system toolbox are highlighted in red.

Introduction
This tutorial will show you the characteristics of the each of proportional (P), the integral
(I), and the derivative (D) controls, and how to use them to obtain a desired response. In
this tutorial, we will consider the following unity feedback system:

Plant: A system to be controlled

Controller: Provides the excitation for the plant; Designed to control the overall
system behavior
The three-term controller
The transfer function of the PID controller looks like the following:

 Kp = Proportional gain
 KI = Integral gain
 Kd = Derivative gain

First, let's take a look at how the PID controller works in a closed-loop system using the
schematic shown above. The variable (e) represents the tracking error, the difference
between the desired input value (R) and the actual output (Y). This error signal (e) will be
sent to the PID controller, and the controller computes both the derivative and the integral
of this error signal. The signal (u) just past the controller is now equal to the proportional
gain (Kp) times the magnitude of the error plus the integral gain (Ki) times the integral of
the error plus the derivative gain (Kd) times the derivative of the error.

This signal (u) will be sent to the plant, and the new output (Y) will be obtained. This
new output (Y) will be sent back to the sensor again to find the new error signal (e). The
controller takes this new error signal and computes its derivative and its integral again.
This process goes on and on.

The characteristics of P, I, and D controllers

A proportional controller (Kp) will have the effect of reducing the rise time and will
reduce ,but never eliminate, the steady-state error. An integral control (Ki) will have the
effect of eliminating the steady-state error, but it may make the transient response worse.
A derivative control (Kd) will have the effect of increasing the stability of the system,
reducing the overshoot, and improving the transient response. Effects of each of
controllers Kp, Kd, and Ki on a closed-loop system are summarized in the table shown
below.

CL RESPONSE RISE TIME OVERSHOOT SETTLING TIME S-S ERROR

Kp Decrease Increase Small Change Decrease
Ki Decrease Increase Increase Eliminate
Kd Small Change Decrease Decrease Small Change
Note that these correlations may not be exactly accurate, because Kp, Ki, and Kd are
dependent of each other. In fact, changing one of these variables can change the effect of
the other two. For this reason, the table should only be used as a reference when you are
determining the values for Ki, Kp and Kd.

Example Problem
Suppose we have a simple mass, spring, and damper problem.

The modeling equation of this system is

(1)

Taking the Laplace transform of the modeling equation (1)

The transfer function between the displacement X(s) and the input F(s) then becomes

Let

 M = 1kg
 b = 10 N.s/m
 k = 20 N/m
 F(s) = 1

Plug these values into the above transfer function

The goal of this problem is to show you how each of Kp, Ki and Kd contributes to obtain

 Fast rise time

 Minimum overshoot
 No steady-state error

Open-loop step response

Let's first view the open-loop step response. Create a new m-file and add in the following
code:

num=1;
den=[1 10 20];
step(num,den)

Running this m-file in the Matlab command window should give you the plot shown
below.

The DC gain of the plant transfer function is 1/20, so 0.05 is the final value of the output
to an unit step input. This corresponds to the steady-state error of 0.95, quite large indeed.
Furthermore, the rise time is about one second, and the settling time is about 1.5 seconds.
Let's design a controller that will reduce the rise time, reduce the settling time, and
eliminates the steady-state error.

Proportional control
From the table shown above, we see that the proportional controller (Kp) reduces the rise
time, increases the overshoot, and reduces the steady-state error. The closed-loop transfer
function of the above system with a proportional controller is:

Let the proportional gain (Kp) equals 300 and change the m-file to the following:

Kp=300;
num=[Kp];
den=[1 10 20+Kp];

t=0:0.01:2;
step(num,den,t)

Running this m-file in the Matlab command window should gives you the following plot.

Note: The Matlab function called cloop can be used to obtain a closed-loop transfer
function directly from the open-loop transfer function (instead of obtaining closed-loop
transfer function by hand). The following m-file uses the cloop command that should
give you the identical plot as the one shown above.
num=1;
den=[1 10 20];
Kp=300;

[numCL,denCL]=cloop(Kp*num,den);
t=0:0.01:2;
step(numCL, denCL,t)
The above plot shows that the proportional controller reduced both the
rise time and the steady-state error, increased the overshoot, and
decreased the settling time by small amount.

Proportional-Derivative control
Now, let's take a look at a PD control. From the table shown above, we
see that the derivative controller (Kd) reduces both the overshoot and
the settling time. The closed-loop transfer function of the given system
with a PD controller is:

Let Kp equals to 300 as before and let Kd equals 10. Enter the following
commands into an m-file and run it in the Matlab command window.

Kp=300;
Kd=10;
num=[Kd Kp];
den=[1 10+Kd 20+Kp];

t=0:0.01:2;
step(num,den,t)

This plot shows that the derivative controller reduced both the
overshoot and the settling time, and had small effect on the rise time
and the steady-state error.

Proportional-Integral control
Before going into a PID control, let's take a look at a PI control. From
the table, we see that an integral controller (Ki) decreases the rise
time, increases both the overshoot and the settling time, and eliminates
the steady-state error. For the given system, the closed-loop transfer
function with a PI control is:

Let's reduce the Kp to 30, and let Ki equals to 70. Create an new m-file
and enter the following commands.

Kp=30;
Ki=70;
num=[Kp Ki];
den=[1 10 20+Kp Ki];

t=0:0.01:2;
step(num,den,t)
Run this m-file in the Matlab command window, and you should get the
following plot.

We have reduced the proportional gain (Kp) because the integral

controller also reduces the rise time and increases the overshoot as the
proportional controller does (double effect). The above response shows
that the integral controller eliminated the steady-state error.

Proportional-Integral-Derivative control
Now, let's take a look at a PID controller. The closed-loop transfer
function of the given system with a PID controller is:
After several trial and error runs, the gains Kp=350, Ki=300, and Kd=50
provided the desired response. To confirm, enter the following commands
to an m-file and run it in the command window. You should get the
following step response.

Kp=350;
Ki=300;
Kd=50;

num=[Kd Kp Ki];
den=[1 10+Kd 20+Kp Ki];

t=0:0.01:2;
step(num,den,t)

Now, we have obtained the system with no overshoot, fast rise time, and
no steady-state error.

General tips for designing a PID

controller
When you are designing a PID controller for a given system, follow the
steps shown below to obtain a desired response.
1. Obtain an open-loop response and determine what needs to be
improved
2. Add a proportional control to improve the rise time
3. Add a derivative control to improve the overshoot
4. Add an integral control to eliminate the steady-state error
 5. Adjust each of Kp, Ki, and Kd until you obtain a desired overall
response. You can always refer to the table shown in this "PID
Tutorial" page to find out which controller controls what
characteristics.

Lastly, please keep in mind that you do not need to implement all three
controllers (proportional, derivative, and integral) into a single
system, if not necessary. For example, if a PI controller gives a good
enough response (like the above example), then you don't need to
implement derivative controller to the system. Keep the controller as
simple as possible.

User Feedback
We would like to hear about difficulties you had with the tutorials,
suggestions you have for improvement, errors that you found, or any
other comments that you have. This feedback is anonymous; include your
email address if you want a reply.

PID Examples
Cruise Control | Motor Speed | Motor Position | Bus Suspension |
Inverted Pendulum | Pitch Controller | Ball and Beam
Tutorials
Basics | Modeling | PID | Root Locus | Frequency Response | State
Space | Digital Control | Examples

8/26/97 DK