Scribd
Upload
21 views3 pages

CEP Assignment 2-PSA&D Fall 2024

Uploaded by

itsme876543
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
21 views3 pages

CEP Assignment 2-PSA&D Fall 2024

Uploaded by

itsme876543
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

ASSIGNMENT (CEP) -2

EE 461 Power System Analysis & Design S-VII EE, Fall 24


Cutoff Date of submission: 30 Dec 2024 Max. Marks: 25
Course Instructor: Dr Ashraf Yahya
------------------------------------------------------------------------------------------------------------------------
An SLD of a five-bus power system is shown below, and the data shown in the Tables

Bus data in Per unit

Bus No δ PG QG PL QL QGmax QG min


1 0 - - 0 0 - -
2 - 0 0 5.0 2.8 - -
3 - 4.0 - 0.8 0.4 4.0 -2.8
4 - 0 0 0 0 - -
5 - 0 0 0 0 - -
S base= 100 MVA , V base= 15 kV at bus 1,3 and 345 kV at buses 2,4,5
Line input data in per unit

From Bus - To R X X0 G B Max MVA


bus

2-4 0.0090 0.100 0.105 0 1.72 12.0


2-5 0.0045 0.050 0.085 0 0.88 12.0
4-5 0.00225 0.025 0 0.44 12.0

Transformer input data in per unit


From bus- to R X X0 Gc Bm Max MVA
bus

1-5 (delta-Y 0.00150 0.02 0,03 0 0 10.0


neutral Gnded)
3-4 (Y-Y both 0.00075 0.01 0.01 0 0 6.0
neutral
grounded)

Generator Data

Bus number X1 X2 X0 Xn
1 0.15 0,15 0,20 0.05
3 0.12 0.15 0.15 0
To solve:
1, It is now required to assess the power flow conditions of the system described above with
both manual calculations and in simulation environment (Powerworld simulator) with the aid
of suitable Algorithm(s). Develop your step-by-step assessment report. Provide solution to any
deviation from normalcy, if identified. The voltage-controlled bus-3 has a target voltage of 1.05
p.u.

2. Create any unsymmetrical fault at any of the buses in the system and calculate the fault
current magnitude. Verify your calculated value by Simulation results in Powerworld simulator
Assessed CLO

CLO No PLO No. BT level Max Marks


3 4 C6 10
4 5 C4 15

------------------------------------------------------------------------------------------------------------------------------
This CEP covers the following range of Complex Problem-solving WPs:

WP1 Depth of knowledge required A thorough understanding of load flow analysis


. iterative procedures and system operations (WK2),
(WK4)
WP3 Depth of analysis required Thorough analysis of system conditions by means of
. interpretation of simulation results
WP7 Interdependence The problem involves many sub problems such as
. interpretation of information, analysis of results, and
suggestion of corrective actions.
WP4 Familiarity of issue Familiarity to a new simulation environment,
. recognition of standard range of bus voltage (WK6)

You might also like