D.

Turbo Function
NINTENDO SWITCH
• This section uses the “A” button as an example. Replace “A”
1. NS (Switch) : Press and hold with another key as needed
the NS Button for 5 seconds • Press A and then T (Turbo) to activate normal Turbo function for
2. On the switch Host, go to A
Controllers> Change Grip/ • Press A and then T (Turbo) again to activate continuous Turbo
ASTRA ONE ULTRA: Quick Start Order function for A
3. Once your controller is • Press A and then T (Turbo) for 3rd time to disable Turbo function
detected on the switch, the for A
LED will turn solid green • While in Turbo mode, Press and Hold Turbo + Left Joystick Up/
4. You are ready to play. Down to adjust turbo

Changing Layout: To switch between Nintendo and XBOX button E. ReCalibration

If the joysticks are not running fully calibrated/ balanced, you can
layout, Press and hold A, Y and Power (wireless Icon) button till you
reset the calibration
feel a vibration
• Press and Hold Select (ST) and Wireless Icon key till Indicator
Other Modes
Lamp turns solid.
• Now release the keys and wait for controller to power off to
(Wireless Icon) 1. V3: Used for games that do not support controllers natively e.g.
complete calibration
* Press and Hold the Wireless Icon button for rst time BGMI/ PUBG
• Please ensure that the sticks are dead centre and your ngers
• Press and Hold the V3 button for 5 seconds to initiate pairing
Bluetooth Pairing with Phones are not touching/ moving the sticks when calibrating
• Install ShootingPlus V3 app from play store
Short Press same button to reconnect for subsequent • Visit our Website Support Section for instruction videos or
The above procedure is for calibrating the controller in Android/iOS/
usage scan QR code on last page
PC mode. To recalibrate for Switch/ V3, press and hold the Select
+ corresponding pairing button instead
2. Android HID Mode
Initial Usage/ Getting Started • Press and Hold the LT + Wireless Icon Button button for 5
F. Gyroscopic Controls
Android/ iOS/ PC/ Mac seconds to initiate pairing
You can assign the gyroscopic controls manually to either Left or
right stick (or turn it off altogether)
1. To get Started, Hold
• Press and hold T (Turbo) button for 8 seconds to activate Gyro
the wireless icon
Charging & Other Features controls for right stick
button for 5 seconds
• Press and hold T (Turbo) button for another 8 seconds to
to power on the A. Charging:
The indicator lamp will blink when activate Gyro controls for Left stick
device and enter •
• Press and hold T (Turbo) button for another 8 seconds to
pairing mode. The charge is low
Connect the supplied USB Type C deactivate Gyro controls
Bluetooth Indicator •

light will ash to USB A cable with a charger to

2. Your device is ready initiate charging SUPPORT
for pairing with your • The Indicator Lamp will ash
Mobile phone (iOS / Wireless Icon slowly while charging In the unlikely event of any issues with pairing or gameplay,
Android) or PC or Mac • The indicator lamp will turn off when please press the reset button (located next to the charging
3. Go to the Bluetooth Menu on your phone/ PC/ Mac to select charging is complete
and pair the controller
interface) with a paper-clip for 5 seconds.
4. You are ready to play. For games that do not support B. Lighting Effects: For any issues, please visit our website https://ninjadog.in
controllers, please refer to the next section • You can Turn Off/toggle LED lighting with Turbo + L3
and use the support form. Alternatively, you can email us at
5. After initial pairing, simply short press the wireless icon button C. Haptics/ Vibration:
to power on • Press and Hold Turbo + Right Stick Up/ Down to change [email protected] or whatsapp/ Call on +91 9372238794
fl
fl
fi
fi