Scribd
Upload
10 views1 page

Aec - Module 1 & 2 - Assignment 1

Uploaded by

rudramuniswsmyhiremath
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
10 views1 page

Aec - Module 1 & 2 - Assignment 1

Uploaded by

rudramuniswsmyhiremath
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

DEPARTMENT OF ELECTRICIAL AND ELECTRONICS ENGINEERING

SUBJECT Analog Electronics Circuits SUB. CODE BEE303


SEMESTER 3rd VTU SCHEME 2022 CBCS
BATCH 2023-24 ACADEMIC YEAR 2022-23
FACULTY Prof. Manjunatha Y DESIGNATION Assistant Professor
ASSIGNMENT NO. 1 DATE 18-12-2023
CO’s 1 and 2 Deadline 30-12-2023

Q Question (C0-1)
No. Module-1
1 Draw a double ended clipper circuit & Explain its working principle with transfer characteristics.
2 With a neat circuit diagram. Explain diode characteristics.

3 Draw & explain the working of clamper circuit which clamps the positive peak of a signal to zero.

4 What is clamping circuit? Explain the negative clamping circuit with & without reference voltage with
necessary waveforms and Applications of clipping and clamping circuits.
5 Define Operating Point? Explain the procedure to find the operating Point (Q-Point) of a transistor.
6 Derive an expression for ETH, IB, &VCE for voltage divider bias circuit analysis.
7 For a voltage divider bias circuit RC=1KΩ, RE=470Ω, R1=10KΩ, R2=5KΩ, β=100. Determine the
stability factor SICO. Draw the circuit diagram.
8 Draw the circuit of voltage divider bias. Take the circuit parameters as Vcc=10V,R2=17KΩ, R1=83KΩ,
RC=2KΩ, RE=0.5KΩ, Find Q Point & terminal voltages. The transistor as β =100 & VBE=0.7V.
9 For a voltage divider bias circuit VCC=18V, RC=3.3KΩ, RE=1KΩ, R1=39KΩ, R2=82KΩ, β=120,
VBE=0.7V. Determine the Q Point and stability factor SICO. Draw the circuit diagram.
10 Consider a fixed bias circuit of a transistor. Obtain expressions for stability factor SICO(S), SVBE(S’),
&Sβ(S’’).Draw the circuit diagram.
11 Explain the operation of transistor as switch with suitable circuit & necessary waveforms.
12 Derive the expression for stability factor for voltage divider biasing circuit with respect to SICO(S),
SVBE(S’).
13 What is bias compensation using thermistor and sensistor?
14 Draw the D.C load line for the Following transistor configuration. Obtain the Q-Point. VCC=12V,
RC=330Ω, RE=200Ω, R1=5.2KΩ, R2=1.24KΩ, β=100, VBE=0.7V.
Q Question (C0-3)
No. Module-3
1 List the general characteristics of negative feedback amplifier.

2 For the voltage series feedback amplifier. Derive an expression for transfer gain, input and output
impedance (Resistance).
3 Explain the general characteristics of negative feedback amplifier.

4 For the Current series feedback amplifier. Derive an expression for Zif and Zof.
5 For the Current shunt feedback amplifier. Derive an expression for transfer gain, input and output
impedance (Resistance).
6 Derive an expression for gain of a feedback amplifier with negative feedback.

a Mr. Manjunath Y (Assistant Professor, Dept. of EEE, GMIT, Davanagere)

You might also like