Model ATC-3200 • Multiple Low Power Operating modes RS-232 Connection

Zigbee to RS232/422/485 Converter • 3-in-1 RS-232/422/485 interface Max.115.2Kbps Serial

User’s Manual interface and zigbee.
• Supports 4- and 2-wire RS-485 with AUTO-SEND ™ and
built-in terminator
• Supports industrial 24 VDC power input and optional Power
over Serial
• Terminal block accessories for easy RS-422/485 serial wiring
• Easy and powerful configuration program RS-422 Connection
Introduction • Approval CE, RoHS
The ATC-3200 is a cost effective and highly integrated Hardware Description
Serial-to-Zigbee wireless Converter. Built on ZigBee technology, 1. RS-232 Pinout：（DB9 Male）
the ATC-3200 is ideal for a range of applications from simple （DB9Male） Signal I/O
RS-232 cable replacement to sophisticated multi-drop RS-485 PIN2 RXD IN
networks and everything in between. Available in PIN3 TXD OUT
RS-232/RS-422/RS-485. PIN5 GND -
ZigBee is the global wireless language connecting dramatically
different devices to work together and enhance everyday life. 2. RS-422/485 Pinout：（six Terminal from left）
The ZigBee Alliance is a non-profit association of more than Terminal RS-485 Connection
1 2 3 4 5 6
280 member companies driving development of ZigBee No
wireless technology. The Alliance promotes world-wide RS-422 T+ T- R+ R- VIN GND
adoption of ZigBee as the leading wirelessly networked, RS-485 485+ 485- - - VIN GND
sensing and control standard for use in energy, home,
commercial and industrial areas. 3. Power Supply：
Features:
ATC-3200 Zigbee converter can adopt the product ’s 9V power
• Utilizes globally available 2.4 GHz ISM band adapter for power supply or adopt power from other DC power or
• Control and Configuration with UART commands. device.(+9--+24V@500-100mA)。
Applications
• 65535 unique node addresses, IDs allow multiple large 4. ATC-3200 LED indication： • Wireless remote control
networks to coexist. SET Indication Zigbee Link ， yellow on Zigbee Link • Building automation
• Programmable Transmit Power Output, max. 12 dBm established。 • Personal area network
• Complete IEEE 802.15.4 spec compliant LINK Data Sending/Receiving between Serial and the • Industrial control
• Typical Receiver Sensitivity –102 dBm Zigbee • OEM equipment
• Typical Throughput rate 250,000 bps PWR Indication Power • PC peripherals
• Obstructed signal range to 500 meters @ 12dBm/PA and
-102dBm/LNA 5. Connection Diagram
Configuration and Operation Selection is complete, click "Write To", began to set Step9. Click "Next", enter the Slave matching images.
1. ATC-3200 default Settings parameters.
Master Com Port No: com1
Slave Com Port No: com1
Pan ID: 5152
Channel: 01-2410MHz
Baud rate: 9,600
Parity Check: Unknow
Encryption:01-Encry
Encryption Key:ffff
Check Time:Unknow Step5. When the screen appears the following screen, on Setp10. Click the "Write To Slave", set the Slave parameters
2. Configure ATC-3200 behalf of parameters are set. start
Step1. Use a configuration cross cable(have been adapted) to Setp11. When the screen appears the following screen, on
make an connection between the ATC-3200 and PC serial port. behalf of parameters are set.

Step2. With a fine needle through the small hole next to the
power plug inside the set by holding down the switch for 5
seconds, the red light flashes. Equipment belonging to the state
can be set. Step6. Click the "Setup Slave", enter the Slave matching
Step3. Start software QR RS232 1 to N, selected using a process.
computer to connect the Master module serial port Step7. Remove Master module, COM Port connection Slave Step12. If the remaining Slave modules required settings, click
module. the "Other Slave". Starting from step 7 to reset.

Step4. Click the “Next” button to read the ATC-3200 firmware Step8. Press the pairing button Slave module until the
configuration. Select Master module parameters. matching light flashes.