DeskTop Theater™5.

1
DTT2500 Digital
Five Satellite/Subwoofer
Speaker System With Dolby Digital Processor
Installation and Operating Instructions

© 1999 Cambridge SoundWorks, Inc.

0420000547 REV. B SINGLE 1 2/9/01, 1:50 PM

 Safety & Regulatory Information
The following sections contain notices for various countries:
Notice for the USA Compliance
FCC Part 15: This equipment has been tested All cables used to connect the computer and Declaration of Conformity This product conforms to the following Council
and found to comply with the limits for a Class B peripherals must be shielded and grounded. According to the FCC96 208 and ET95-19
Operation with non- certified computers or non- Directive:
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide shielded cables may result in interference to Name: Creative Labs Inc. • Directive 89/ 336/ EEC, 92/ 31/ EEC (EMC),
reasonable protection against harmful radio or television reception. Address: 1901 McCarthy Boulevard
interference in a residential installation. This 73/23/EEC (LVD)
Milpitas, CA. 95035
equipment generates, uses, and can radiate radio Modifications United States
frequency energy and, if not installed and used Any changes or modifications not expressly Tel: (408) 428-6600
in accordance with the instructions, may cause approved by the grantee of this device could void
the user’s authority to operate the device. declares under its sole responsibility that the
harmful interference to radio communications. product
However, this notice is not a guarantee that
interference will not occur in a particular Notice for Canada Trade Name: Creative Labs/
installation. If this equipment does cause This apparatus complies with the Class B limits Cambridge SoundWorks
harmful interference to radio or television for radio interference as specified in the Model Number: CSW3500
reception, which can be determined by turning Canadian Department of Communications Radio
the equipment off and on, the user is encouraged Interference Regulations. has been tested according to the FCC / CISPR22/85
to try one or more of the following measures: requirement for Class B devices and found
Cet appareil est conforme aux normes de CLASSE compliant with the following standards:
• Reorient or relocate the receiving “B” d’interference radio tel que spe’cifie’ par le EMI/ EMC: ANSI C63.4 1992, FCC Part 15 Subpart
antenna. Ministère Canadien des Communications dans les B
• Increase the distance between the règlements d’interfèrence radio.
This device complies with part 15 of the FCC
equipment and receiver. Rules. Operation is subject to the following two
• Connect the equipment to an outlet on a conditions:
circuit different from that to which the 1. This device may not cause harmful
receiver is connected. interference, and WARNING: To prevent fire
• Consult the dealer or an experienced 2. This device must accept any interference or shock hazard, do not
radio/ TV technician. received, including interference that may expose this appliance to
cause undesirable operation. rain or moisture.
CAUTION: To comply with the limits for the
Class B digital device, pursuant to Part 15 of the Ce matériel est conforme à la section 15 des
FCC Rules, this device must be installed with régles FCC. Son fonctionnement est soumis aux
computer equipment certified to comply with the deux conditions suivantes:
Important Notice
Class B limits. 1. Le matériel ne peut étre source d’interférences
et The serial number for the DTT2500 Digital is
located on the Decoder Amplifier. Please write
2. Doit accepter toutes les interférences reques, Y this number down and keep it in a secure area.
compris celles pouvant provoquer un
fonctionnement indésirable. This is for your security.

Compliance Manager
Creative Labs, Inc.
March 4, 1999

0420000547 REV. B SINGLE 2 2/9/01, 1:50 PM

 IMPORTANT SAFETY INSTRUCTIONS
READ INSTRUCTIONS - All safety and oper- should use a mounting accessory recom- the plug fully into the outlet, try reversing DAMAGE REQUIRING SERVICE - Unplug
ating instructions should be read before the mended by Cambridge SoundWorks. the plug. If the plug should still fail to fit, the power supply from the wall outlet or
DTT2500 Digital amplified subwoofer/sat- VENTILATION - Slots and openings in the contact your electrician to replace your other power source and refer servicing to
ellite system is operated. Decoder Amplifier are provided for venti- obsolete outlet. Do not defeat the safety qualified service personnel under the fol-
RETAIN INSTRUCTIONS - The safety and lation and to ensure reliable operation of purpose of the polarized plug. lowing conditions:
operating instructions should be retained the Decoder Amplifier and to prevent it POWER-CORD PROTECTION - Power sup- a) When the power supply cord or plug is
for future reference. from overheating. These openings must ply cords should be routed so that they are damaged.
HEED WARNINGS - All warnings on the not be blocked or covered. The openings not likely to be walked on or pinched by b) If liquid has been spilled, or objects
subwoofer and in the operating instruc- should never be blocked by placing the items placed upon or against them, paying have fallen into the subwoofer.
tions should be adhered to. product on a bed, sofa, rug, or other simi- particular attention to cords at plugs, con- c) If the Decoder Amplifier has been ex-
FOLLOW INSTRUCTIONS - All operating lar surface. The Decoder Amplifier should venience receptacles, and the point where posed to rain or water.
and use instructions should be followed. not be placed in a built-in installation such they exit from the Decoder Amplifier. d) If the subwoofer does not operate nor-
CLEANING - Unplug the Power Supply as a bookcase or rack unless proper ven- LIGHTNING - For added protection for the mally by following the operating instruc-
Adapter from the wall outlet or other power tilation is provided or Cambridge DTT2500 Digital system during a lightning tions; or exhibits a distinct change in per-
source before cleaning. Do not use liquid SoundWorks’ instructions have been ad- storm, or when it is left unattended and formance.
cleaners or aerosol cleaners. Use a damp hered to. unused for long periods of time, unplug it e) If the product has been dropped or
cloth for cleaning. HEAT - The Decoder Amplifier should be from the wall outlet. This will prevent dam- damaged in any way.
ATTACHMENTS - Do not use attachments situated away from heat sources such as age to the Decoder Amplifier due to light- REPLACEMENT PARTS - When replace-
not recommended by Cambridge radiators, heat registers, stoves, and other ning and power-line surges. ment parts are required, be sure the ser-
SoundWorks as they may cause hazards. products (including amplifiers) that pro- OVERLOADING - Do not overload wall out- vice technician has used replacement
WATER AND MOISTURE - Do not use the duce heat. lets, extension cords, or integral conve- parts specified by Cambridge SoundWorks
Decoder Amplifier near water—for ex- POWER SOURCES - The Decoder Amplifier nience receptacles as this can result in a or have the same characteristics as the
ample, near a bath tub, wash bowl, kitchen should be operated only from the type of risk of fire or electric shock. original parts. Unauthorized substitutions
sink, or laundry tub; in a wet basement; or power source indicated on the marking OBJECT AND LIQUID ENTRY - Never push may result in fire, electric shock, or other
near a swimming pool; and the like. label. If you are not sure of the type of objects of any kind into the Decoder Am- hazards.
ACCESSORIES - Do not place the DTT2500 power supply to your home, consult your plifier through openings as they may touch SAFETY CHECK - Upon completion of any
Digital Decoder Amplifier on an unstable product dealer or local power company. dangerous voltage points or short out service or repairs to the DTT2500 Digital
cart, stand, tripod, bracket, or table. The For products intended to operate from parts that could result in a fire or electric system, ask the service technician to per-
Decoder Amplifier may fall, causing seri- battery power, or other sources, refer to shock. Never spill liquid of any kind on the form safety checks to determine that the
ous injury to a child or adult, and serious the operating instructions. speakers or the Decoder Amplifier. DeskTop Theater 5.1 system is in proper
damage to the product. Use only with a POLARIZATION - The power supply may be SERVICING - Do not attempt to service the operating condition.
cart, stand, tripod, bracket, or table rec- equipped with a polarized alternating-cur- any part of the DTT2500 Digital yourself WALL OR CEILING MOUNTING - The
ommended by Cambridge Sound-Works, rent line plug (a plug having one blade as opening or removing covers may ex- DTT2500 Digital satellites should be
or sold with the product. Any mounting of wider than the other). This plug will fit into pose you to dangerous voltage or other mounted to a wall or ceiling only as rec-
the satellites or subwoofer should follow the power outlet only one way. This is a hazards. Refer all servicing to qualified ommended by Cambridge SoundWorks.
the manufacturer’s instructions, and safety feature. If you are unable to insert service personnel.

ii

0420000547 REV. B SINGLE 3 2/9/01, 1:50 PM

 Contents
DeskTop Theater 5.1 Declaration Of Conformity ................................................................... i
Safety Precautions .......................................................................... i, ii
Introduction ....................................................................................... 1

DTT2500 Digital Inspecting For Damage ....................................................................... 2

Important Notes .................................................................................. 2
Installation Sequence .......................................................................... 3
Speaker Placement .............................................................................. 3
Speaker Wire and Stand Installation .................................................... 6
Mounting The Speakers ...................................................................... 7
Decoder Amplifier Placement ............................................................... 8
Making Connections ........................................................................... 8
Wiring Diagram .................................................................................. 9
Connection to Sound Blaster Live! Via Digital DIN ............................... 9
Decoder Amplifier Functions ............................................................. 10
Surround Reference .......................................................................... 12
Dolby Digital ................................................................................. 12
Dolby Surround with Pro Logic ...................................................... 12
Creative Multi Speaker Surround .................................................... 13
Audio Mode Selection .................................................................... 13
Applications Guide ............................................................................ 14
Specifications .................................................................................... 18
Important ......................................................................................... 18
Technical Support ............................................................................. 18
1-Year Limited Warranty .................................................................. 20

iii

0420000547 REV. B SINGLE 4 2/9/01, 1:50 PM

 Introduction
T
hank you for purchasing Cambridge SoundWorks
DeskTop Theater 5.1 1-800-FOR-HIFI
DTT2500 Digital by (1-800-367-4434),
Cambridge SoundWorks. 8 AM to Midnight,
DeskTop Theater 5.1 DTT2500 Eastern time
Digital lets you experience the full 1 PM to 4 AM
potential of Dolby®Digital Greenwich Mean Time
multichannel sound from your In Canada: 1-800-525-4434
computer DVD player, with a Outside US or Canada:
dynamic output that rivals a Tel: 617-332-5936
component home theater system. Fax: 617-527-3194
It processes both Dolby Digital and www.hifi.com
Dolby Surround program material. or e-mail us at [email protected]
DeskTop Theater 5.1 DTT2500
Digital offers discrete four-channel
support for Microsoft® DirectSound®
3D and its other derivatives. In
some of today’s best CD-based
action games, DeskTop Theater 5.1
DTT2500 Digital can automatically
decode the Dolby Surround cut-
scenes while offering enveloping
positional four channel audio. It’s
ready for the new era of DVD-based
games.
Also included is Creative Multi
Speaker Surround, which lets you
hear all of your favorite stereo
program material with a new and
exciting three-dimensional quality.

0420000547 REV. B SINGLE 5 2/9/01, 1:50 PM

 Inspecting
For Damage Important Notes
Examine each unit carefully for These instructions assume you should utilize the exclusive Digital that are 3 meters (9 feet) long. The
signs of shipping damage. If there is have a DVD player with a coaxial DIN connection, to hear the other pair has cables that are 5
any damage, do not install the Dolby Digital (AC-3) output (for clearest digital audio available. meters (16 feet) long. Typically, the
system. Consult the store where you example, the Creative Labs PC-DVD Conventional 2-channel sound two satellites with the longer
purchased the system or call the Encore). These instructions also cards such as Sound Blaster 16 or cables will be used on the surround
appropriate Creative Technology, Ltd. assume your sound card supports the Sound Blaster AWE series can channels, but the satellites are
support group at the number listed processing of DirectSound®3D, also be used with DTT2500 otherwise identical. If you need
at the end of this publication. Save including front and rear two- Digital, but these cards will not extra cable length for the front
the shipping carton and inserts in channel minijack line outputs (like provide rear channel output when channel satellites, use the pair
case you have to transport the Creative Labs Sound Blaster PCI playing games using with the longer cables instead.
system later. series or Sound Blaster Live! DirectSound®3D or its derivatives. All the speakers are magnetically
All the items shown in the series). Sound Blaster Live! owners One pair of satellites has cables shielded, but the subwoofer is not.
illustration should be included. If
anything is missing, notify the
retailer.

Holder/Cap (2) Satellites (5) 3 meter speaker wires (4)

PRO LOGIC
DOLBY
MUSI MOVI FOURPOIN STEREO DIGITA DIGITAL IN ANALOG IN LL R
L

CREATIVE DOLBY AUDIO SPEAKER MUT

MULTI SPEAKER

Supports (6) DTT 3500 DIGITAL

POWER

MASTE CENTE SUBWOOFE SURROUND

(5) Wall Mounting Hardware

Quick Reference Guide Decoder Amplifier Strips of 4 feet (5) 5 meter speaker wires (2)
SPDIF DIN Cable
Feet (6)

SUB
RS
LS
R

C
L
L R LS RS SUB C
Tandem Audio Cable (Green and Black Miniplugs)
L R LS RS SUB C
Support Extends (18) Frames (2)
Desktop Stands for satellites (5) Monitor Stand SPDIF Cable (RCA to RCA) Hook and Loop Fasteners (10) Satellite Position Stickers

0420000547 REV. B SINGLE 6 2/9/01, 1:50 PM

 Installation Sequence Speaker Placement
1. Read all of the instructions should use the supplied cable to The Front Satellites. The left front The satellites may also be hung
before installing the speaker connect it to the Digital DIN and right front satellites play on the wall behind the monitor
system. input instead. stereo music, the off-screen sounds using the screw and wall anchors
2. Using the placement instruc- 6. With the Decoder Amplifier’s of video playback and the front provided (see Mounting The
tions as a guide, position the power switch “off”, connect the channels of four channel games. Speakers, page 7).
satellites, the center channel power supply adaptor to the These satellites should be placed If you wish to save desktop
speaker and subwoofer around Decoder Amplifier. to the sides of your monitor (see space, use the hook and loop
your computer. Install the 7. Turn on the power. Use the Diagram A). Be sure to have a fasteners to attach the satellite
Desktop Stands and Floor SPEAKER TEST mode to position clear line of sight from your speakers to the sides of the
Stands as appropriate. If you and balance the speakers. listening position to these computer monitor (see Diagram B).
wish to substitute a powered 8. You may wish to experiment satellites. The satellites intended The Center Channel Speaker. The
subwoofer for the subwoofer with speaker placement briefly for front placement have 3 meters center channel speaker provides
that comes with the DTT2500 before concealing the connecting (9 feet) of cable. the on-screen effects and dialog in
Digital, read Substituting a cables and making the installa- Install the satellite’s Desktop Dolby Digital, Dolby Surround or
powered subwoofer page 5. tion more permanent. Stands when using them on the Creative Multi Speaker Surround
3. Connect the satellite speakers, 9. The unit is ready for you to desktop (see page 6). modes. It should be placed as close
center channel speaker, and enjoy. Refer to the Quick to the center of your computer
subwoofer to the back of the Reference guide for information monitor as possible.
Decoder Amplifier. about settings for specific
4. Connect the Dolby Digital output program sources like DVD, CDs,
of your digital program source Video CD and games.
(typically a DVD player) to the A B
Dolby Digital input of the
Decoder Amplifier.
5. Connect your normal audio
PRO LOGIC
DOLBY
MUSIC MOVIE FOURPOINT STEREO DIGITAL DIGITAL IN ANALOG IN LL RR

CREATIVE DOLBY SURROUND AUDIO MODE SPEAKER TEST MUTE

MULTI SPEAKER SURROUND

POWER

DTT 3500 DIGITAL MASTER CENTER SUBWOOFER SURROUND

signal sources via the Line In

and Rear In inputs. An owner of
a Sound Blaster Live! sound
card with a Digital DIN output

0420000547 REV. B SINGLE 7 2/9/01, 1:50 PM

 There are many mounting channel so that it is as far forward Speaker Surround modes. They at the same height as the front
possibilities. The monitor stand as possible. also provide the discrete rear satellites.
can be attached with hook and Use a Desktop Stand to position sounds produced in four channel If you have side walls close to
loop fasteners to the top of the a center channel satellite in front gaming. your listening position, excellent
computer monitor. It directs the of the monitor. It directs the sound 5 meters (16 feet) of cable is placement for the rear satellites is
sound down towards the listener up towards the listener (see provided with the two remaining slightly behind your listening
(see Diagram C). Diagram E). small satellites for more flexibility position, slightly above ear level
If your computer monitor’s The Center Speaker may also be in rear channel placement. (see Diagram F). The satellites may
construction directs the sound of hung on the wall behind the The rear satellites may be placed be hung on the wall using the
the center channel satellite monitor using the screw and wall in any convenient sites alongside screw and wall anchors provided
towards you without a stand, anchors provided (see Mounting the listener, including sites slightly (see Mounting The Speakers, page 7).
attach the satellite directly to the The Speakers, page 7). forward of the listening location. Do not be concerned if this
top of the monitor, using the hook The Rear Satellites. The rear The rear satellites do not have to placement is not practical. Any
and loop fasteners (see Diagram satellites provide the surround be at exactly the same height, nor rear satellite placement to the left
D). Position the face of the center effects in Dolby Digital, Dolby and right side of the listening
Surround and Creative Multi position will provide strong
directional and surround effects.

C D E

F G

0420000547 REV. B SINGLE 8 2/9/01, 1:50 PM

 The rear satellites may be Also, you may attach the rear recommend placing the subwoofer inches away from a computer
installed on their convenient floor satellites under a desktop or at the on the floor (see Diagram J). monitor.
stands. While listening, the stands sides of a desk using the hook and Leave at least 8 cm (3 inches) of Substituting a powered
should be positioned to the left and loop fasteners (see Diagram I). space between the subwoofer face subwoofer. You may substitute a
right of your listening position (see After you have positioned the and a wall. Small objects in front powered subwoofer for the
Diagram G on the previous page). rear satellites, use the test sound of, but not touching the subwoofer subwoofer that comes with the
The Floor Stands are small to make sure each speaker can be (table legs, for instance) will have DTT2500 Digital. Connect its line
enough to be stowed underneath a heard clearly. no effect on its sound. If you have level input (typically an RCA jack)
desk when not in use. See page 7 The Subwoofer. The subwoofer’s no available floor space, the to the dedicated subwoofer output
for floor stand assembly instruc- optimum position is on the floor subwoofer can be placed on a on the back of the Decoder
tions. against the wall under the shelf, desktop or other sites, but its Amplifier, using a shielded audio
Larger work surfaces can computer desk. The nearer the maximum output will be reduced. cable with RCA plugs on each end.
accommodate both front and subwoofer is to the corner of the The subwoofer is not magnetically Refer to the powered subwoofer’s
surround pairs of satellites on room, the stronger its maximum shielded, so position it at least 18 User Manual for adjustment
their Desktop Stands. Try the bass output will be. We strongly procedures.
extreme corners of a desk using
the Desktop Stands (see Diagram H).

H I J

0420000547 REV. B SINGLE 9 2/9/01, 1:50 PM

 Speaker Wire and Stand Installation
Typically, the 3 meter speaker 3. Remove the backing from the Diagram K: To connect the
cables will connect the front and remaining, longer “L” label and speaker wire to each satellite,
center satellites to the Decoder wrap it around the opposite end press one of the spring-loaded tabs
Amplifier and the 5 meter cables of the speaker cable near the to expose the connection hole.
will connect the rear satellites to RCA-type plug. Insert the bare end of the wire
the Decoder Amplifier. A panel of 4. Place the satellite in the front into the exposed hole, then release
twelve self-adhesive labels is left position. the tab to lock the wire in place. L
REAR
C

C
RIGHT

SUB

SUB
SUB

provided to identify each satellite 5. Repeat this process using Connect wires with red bands to

RS

RS
RS

and subwoofer and the opposite another 3 meter cable for the red tab connectors, and unmarked K

LS

LS
LS

R
end of the cable connected to a front right satellite, using the wires to black tab connectors.

R
satellite and subwoofer. “R” labels. Notes: Matching red wires to red
1. Identify a 3 meter cable. Most 6. Connect another 3 meter cable to tabs and unmarked wires to black
often, a satellite will be used a satellite. Use the “C” (center) tabs insures the speakers all play
with a desktop stand. In this labels. If used, the Monitor “in phase”. “Out-of-phase”
case, thread the bare wire end of Stand attaches to the satellite in connections will do no electrical
a 3 meter cable through the hole the same manner as the harm, but the overall sound
in the desktop stand. Connect Desktop Stands, although it quality will be greatly reduced.
this end to a satellite (as shown does not have a hole for the You can substitute regular 18
in Diagram K). Carefully insert speaker wire. Route the wire to gauge speaker wire to create
the desktop stand’s attachment the left or right side of the longer cables, if needed.
arm into the socket in the back attachment strut. Position the
of the satellite, taking up any satellite.
slack in the cable as required. 7. If you wish to use the Floor
2. To use this satellite in the front Stands with the rear satellites,
left position, remove the backing assemble the stand according to DOLBY DIGITAL LINE IN REAR IN DIGITAL ANALOG AUTO
(AC-3) SPDIF IN DIN
from the small, round “L” label Attaching The Floor Stand SUBWOOFER
INPUT 15V
DC IN
LINE OUT SPEAKER OUTPUTS
and apply it to the back of the instructions on page 7. Use the C SUBWOOFER RS LS R L
satellite (see Diagram K). RS and LS labels (right and left
surround) and 5 meter cables.
8. Connect the subwoofer using the
last 3 meter cable to the “SUB”
labels. L

0420000547 REV. B SINGLE 10 2/9/01, 1:50 PM

 Mounting The Speakers
Screw Mounting: The Satellite Plastic anchors may be needed to Hook and Loop Fasteners: When
and Center Channel speakers may secure the screws into particularly mounting speakers with hook and
be hung on a wall using an M5 hard or soft material. If so, drill the loop fasteners, make sure that all
screw and their keyhole openings. appropriate sized holes in the wall surfaces are clean and free of dirt
First attach four self-adhesive and tap the anchors into the holes and grease. Hard, flat, unpainted
feet to the back of each satellite until they are flush with the wall. surfaces work best with hook and
(see Diagram P) insuring a Insert the screws into the anchors loop fasteners (see Diagram Q).
vibration-free, secure installation. until they protrude 3/8 inch from Attach the fastener first to a
Leave about 3/8 of an inch of the the wall. speaker. Then remove the
screw-head exposed to fit into the remaining backing and adhere to
back of the speaker. the chosen surface.

P Q
L
REAR
RIGHT

PRO LOGIC
DOLBY
MUSIC MOVIE FOURPOINT STEREO DIGITAL DIGITAL IN ANALOG IN LL RR

CREATIVE DOLBY SURROUND AUDIO MODE SPEAKER TEST MUTE

MULTI SPEAKER SURROUND

POWER

DTT 3500 DIGITAL MASTER CENTER SUBWOOFER SURROUND

0420000547 REV. B SINGLE 11 2/9/01, 1:50 PM

 Decoder Amplifier
Placement Making Connections
The Decoder Amplifier can be R Consult the Wiring Diagram on connect a cable to the Line In and
placed on the desktop, a shelf or the next page before making any Rear In input in this instance.
any site that makes the controls connections. Refer to Connection to Sound
convenient (see Diagram R). MUSIC MOVIE

CREATIVE
FOURPOINT

MULTI SPEAKER SURROUND

STEREO
DOLBY
PRO LOGIC
DIGITAL DIGITAL IN ANALOG IN

DOLBY SURROUND
LL RR

AUDIO MODE SPEAKER TEST MUTE

Speaker Connections. Insert one Blaster Live! via Digital DIN

The Power Adapter cord must be (next page) for more information
POWER

DTT 3500 DIGITAL MASTER CENTER SUBWOOFER SURROUND

satellite’s plug into the corre-

able to reach from the Decoder sponding Speaker Output on the about this connection.
Amplifier back panel to your AC Decoder Amplifier. Repeat this For all other sound cards: Use
power receptacle. process for the remaining the tandem audio signal cable.
Place the Decoder Amplifier on a satellites and subwoofer. If Connect the green stereo
hard, flat surface. substituting a powered miniplugs to the Line Out
There are ventilation slots on the subwoofer, connect it to the minijack output of your sound
bottom and top of the Decoder SUBWOOFER LINE OUT. card and to the Line In minijack
Amplifier’s enclosure. Don’t block output of the Decoder Amplifier.
the ventilation slots by placing Signal Connections. Connect the black stereo
material on top of or below the Dolby Digital. Connect the Dolby miniplugs to the Rear Out
Decoder Amplifier. Digital/SPDIF output of your minijack output of your sound
signal source to the Decoder card (if present) and to the Rear
Amplifier’s Dolby Digital input In minijack input of the Decoder
using the cable with the RCA Amplifier.)
plugs at each end. Power Supply Adapter Connec-
For Sound Blaster Live! sound tions. Confirm the power switch
cards with a digital I/O card: is in the “OFF” position. Insert
Connect its Digital DIN output to the power supply’s AC plug into
the Digital DIN input with the an appropriate receptacle. Insert
supplied Digital DIN cable (the the small DC connector into the
one with the red plugs at each “15V DC IN” receptacle on the
end). It is not necessary to back of the Decoder Amplifier.

0420000547 REV. B SINGLE 12 2/9/01, 1:50 PM

 Connection to Sound BLaster
Wiring Diagram Live! via Digital DIN
DVD OUTPUT
(EXAMPLE: CREATIVE LABS SOUNDCARD OUTPUT If your Sound Blaster Live! sound • Bring your mouse pointer to
PC-DVD ENCORE Dxr2) (EXAMPLE: SOUND BLASTER LIVE!)
DIGITAL REAR LINE
card includes a Digital I/O card, the top of the monitor screen
OUTPUT OUT OUT you can take advantage of the to display the Creative
clear, distortion-free audio Launcher.
available from its Digital DIN • Click on AudioHQ.
output. • Click on the Speaker tab.
GREEN

BLACK
1. Insert on end of the SPDIF The speaker dialog box will
cable into the Digital DIN appear.
DOLBY DIGITAL LINE IN REAR IN DIGITAL ANALOG AUTO
output jack on the Sound • On the configuration tabbed
(AC-3) SPDIF IN
SUBWOOFER
DIN
INPUT 15V
Blaster Live! Digital I/O card. page, select the “4 Speakers”
LINE OUT SPEAKER OUTPUTS
C SUBWOOFER RS LS R L
DC IN
The position of the Digital DIN option.
connector on the Digital I/O • A sofa icon (representing you)
card may be different from this appears in the center of the
POWER
SUPPLY
diagram. The Digital DIN preview box, with four speakers
ADAPTER connector is the only connector at the corners of the box.
with a 9-pin configuration. • In some versions of Sound
2. Insert the other end of the Blaster Live! software, you can
SPDIF cable into the Digital select the “four-speaker” output
DIN input on the decoder option in the Environment deck
amplifier. of the Surround Mixer applica
3. Use the following procedure to tion (located in the Sound
configure the Sound Blaster Blaster Live! program tab of the
Live! sound card for four Creative Launcher).
speakers: Note: When the Analog/Auto
RIGHT SURROUND LEFT SURROUND
SATELLITE SUBWOOFER SATELLITE SPDIF CABLE switch is pushed towards the Auto
side, the signal at the Digital DIN
input is given priority and the
signal at the Analog Audio inputs
will be ignored. To listen to a
DOLBY DIGITAL LINE IN REAR IN DIGITAL ANALOG AUTO
(AC-3) SPDIF IN DIN DIGITAL I/O CARD DIGITAL DIN Digital DIN Connector
SUBWOOFER
INPUT 15V
LINE OUT SPEAKER OUTPUTS DC IN
C SUBWOOFER RS LS R L
sound source through the analog
RIGHT SATELLITE CENTER CHANNEL LEFT SATELLITE DTT2500 Digital Decoder Amplifier
audio inputs, push the switch to
SPEAKER
the Analog side.

0420000547 REV. B SINGLE 13 2/9/01, 1:50 PM

 Decoder Amplifier Functions
When the power is switched Top Row No lights illuminated: Mutes Repeated presses of the button
“ON”, the green indicator lights 4. Creative Multi Speaker any analog stereo or CMSS selects which channel is fed to
on the face of the Decoder Surround: CMSS processes output. Use this setting if you both the Left and Right front
Amplifier will sequentially light analog program material. wish to play an analog stereo speakers.
from the left to the right. The Repeated presses of this button signal through the Dolby Pro LL-Left channel to both Left and
CMSS Music light will remain steps through five different Logic processor. For more Right front speakers.
illuminated after start-up. The operation modes. information about Creative Multi RR-Right channel program to
indicator light for Dolby Digital Music: Creates a 5.1 speaker Speaker Surround, see page 13. both Left and Right front
will illuminate automatically if a soundfield appropriate for music 5. Dolby Digital indicator light: speakers. See Audio Mode
Dolby Digital program is playing. from any analog sound source. This light turns on whenever a Selection, page 13 for further
1. ON/OFF: Switches DeskTop Movie: Creates a 5.1 speaker Dolby Digital signal is detected at information about this feature.
Theater DTT2500 Digital power soundfield appropriate for movie the SPDIF input of the DTT2500 8. Speaker Test: Press this
on and off. An indicator light or game enjoyment from an Digital. For Dolby Digital 5.1 button to start the “test sound”
signals the power is on. analog sound source. sound reproduction, make sure generator. Use this test sound to
FourPoint: Use this mode for only this light is illuminated. position all the speakers and to
2. Master: Adjusts the volume of 6. Dolby Surround: This button balance their relative output.
DVD games having Dolby Digital
the entire system. cycles between Dolby Pro Logic The test sound moves in sequence
soundtracks with Environmental
3. Center, Subwoofer and Audio Extensions or Microsoft® processing of the digital signal, from the left satellite, the center
Surround: These controls adjust DirectSound®3D for real-time then the analog input and no Pro speaker, the right satellite, then
the level of the indicated positioning of sound effects. Logic processing. To decode to the right surround satellite,
channels. Their output level Stereo: Use this mode when you Dolby Surround program at the left surround satellite and the
should be balanced with the fixed want to hear just stereo effects or Digital DIN input, select the subwoofer. All of the indicator
output level of the Left and Right Analog Pro Logic mode. lights will blink on and off while
front speakers. 7. Audio Mode: Use this button the test sound generator is in
A Quick Reference Guide is to play just the left or right operation.
provided separately. channels of a stereo digital The test sound will operate for
Consult this guide for signal (PCM from an audio CD, a three complete cycles and then
advice about playing Video CD or a stereo signal from stop. You can terminate the sound
different program sources. a DVD). Use this when, for at any point by pressing the Speaker
Slip it underneath the example, a Video CD has different Test button again.
Decoder Amplifier for languages on the left and right First use the test sound to verify
future use.
channels. that each speaker is operating.

10

0420000547 REV. B SINGLE 14 2/9/01, 1:50 PM

 Then make sure the speakers The speaker level controls
are positioned so that the test operate at all times. If desired,
sound can be clearly heard. you may adjust these controls
Finally, adjust the front panel during program material to fine-
level controls for the center, tune the balance.
subwoofer and rear speakers. 9. Mute: Mutes all output from
Adjust each control so its speaker the DTT2500 Digital. Press the
achieves a balanced output level button once to mute. Press a
with the left and right satellites second time to restore audio
(which provide a fixed “reference” output.
output level). The CMSS, Dolby Surround,
All Decoder Amplifier functions Audio Mode and Speaker Test
except for the level controls are buttons are operable during
disabled while the test sound is mute.
running.
PRO LOGIC
DOLBY
MUSIC MOVIE FOURPOINT STEREO DIGITAL DIGITAL IN ANALOG IN LL R

5
4 6 7 8 9
CREATIVE DOLBY SURROUND AUDIO MODE SPEAKER TEST MUTE
MULTI SPEAKER SURROUND

POWER
CAMBRIDGE
SOUNDWORKS 1 MASTER
2 CENTER SUBWOOFER SURROUND

11

0420000547 REV. B SINGLE 15 2/9/01, 1:50 PM

 Surround Reference
Dolby Digital When listening to DVD movies Dolby Pro Logic CD-ROMs and CD’s with Dolby
Dolby Digital (earlier called AC-3) with 5.1 channel Dolby Digital Dolby Surround is an earlier Surround encoding will feature
delivers five discreet full-range sound, be sure to listen only to the surround sound standard which is the Dolby Surround logo at the
channels (left front, center, right digital program source. You can decoded with a Pro Logic processor beginning of the program or on the
front, left surround and right insure this by: in the DTT2500 Digital. The Pro packaging. Process these programs
surround) plus a separate Low 1) making sure your DVD Logic steering circuitry derives by making sure all CMSS indicator
Frequency Effects (LFE) channel. player’s stereo downmix is separate center and rear channels lights are off and selecting the Pro
Many soundtracks on the latest not sent to your soundcard. For from encoded stereo program Logic Analog Input setting of the
generation laser discs, DVDs and example, disconnect any cable sources. Surround Mode button. Use this
High Definition Television (HDTV), link between the cards. Pro Logic processing provides a Analog Pro Logic Mode to decode
are encoded with Dolby Digital 2) making sure all four CMSS convincing movie soundfield when Dolby Surround program material
technology. indicator lights are off the material is specifically encoded at the Digital DIN input.
When a 5.1 channel Dolby (MUSIC, MOVIE,FOURPOINT for Dolby Surround. Most older Do not select a Pro Logic
Digital program source is playing, and STEREO) stereo movie soundtracks will only decoding mode if the program
such as from a Creative PC-DVD 3) muting the “CD” input of be encoded for Dolby Surround, material is not encoded for Dolby
player, the Dolby Digital indicator your computer’s software mixer/ even though the program source Surround. Excessive center
light will illuminate automatically. volume control application. may be a DVD’s digital output. channel output will result, and
Note: Not every section of a DVD When playing a DVD game with Most DVDs containing Dolby most stereo effect will be lost. Use
will be 5.1-channel encoded. On a mix of Dolby Digital 5.1 sound (a Surround program material will CMSS “Movie” or “Music” modes
many DVDs, only the main movie digital signal at the SPDIF input) cause both the Dolby Digital and to upmix stereo programs to a
program will be available in 5.1 and soundcard wavetable output Digital Pro Logic lights to realistic 5.1 channel sound field.
channel sound. Other supporting (a signal at the analog input), be illuminate. DTT2500 Digital will
chapters (like a “Director’s sure to engage the FOURPOINT decode these digitally transferred
Comment” section) may be in mode in the CMSS settings. Dolby Surround programs through
stereo or mono. These sections will the digital Pro Logic decoder
not light the Dolby Digital indicate automatically.
or even though the sound will be
properly reproduced by the
DTT2500 Digital.

12

0420000547 REV. B SINGLE 16 2/9/01, 1:50 PM

 Creative Multi Speaker Unlike Pro Logic decoding, CMSS Audio Mode Selection during stereo playback, select the
Surround (CMSS) Music, Movie and Four Point
modes are appropriate for use with
The stereo soundtracks of some “LL” and “RR” settings until you
find the language soundtrack you
CMSS is a 2-channel to 5.1- movies on the Video CD (VCD
multi-coded sources such as DVD format) contain different lan- want.
channel sound processor similar in games. In some game titles, the The Audio Mode selection feature
some aspects to a Dolby Surround guages. For example, a two
movie sequences may be encoded channel soundtrack may contain can only be used with the PCM
with Pro Logic processor. in Dolby Surround but the game digital soundtrack of a Video CD or
CMSS Music mode creates a Mandarin on the right channel and
sequences may be in the WAV English on the left channel. The DVD with a stereo soundtrack, not
convincing 5.1 channel surround format. CMSS Movie mode a DVD encoded with Dolby Digital
soundfield with typical stereo VCD program literature should
supports 6-channel output for indicate the presence of dual- 5.1 sound or Dolby Surround-
sources, whether they are Dolby .WAV, .AVI, .MIDI and other audio encoded material. If you have an
Surround-encoded or not. It works language soundtracks. Similarly,
software formats. Few, if any of some movies in the DVD format analog program with separate left
well with Dolby Pro Logic, WAVE, these kinds of formats are Dolby and right channels (the analog
AVI and MIDI program material. In will contain dual-language
Surround encoded. soundtracks. DTT2500 Digital lets output of a CD ROM, or the analog
essence, CMSS Music mode puts The FOURPOINT mode passes stereo output of a “software” video
you “on the stage” for the you select one of these languages
the four discreet channel audio of and play it through both the Left CD, for instance), you will have to
music’s performance, surround- four-channel games direct to each use the balance control in your
ing you with the performers. and Right speakers.
satellite channel. It does not If there is no indication of which PC’s audio software to mute the
In a similar manner, CMSS Movie synthesize rear channel output, so undesired channel.
mode provides the sonic impres- channel is which and you hear two
stereo signal in this mode will play different language soundtracks
sion of being front and center at a just through the front two speakers
movie screening. Dialog and all and subwoofer.
normally centered sounds from a The STEREO mode plays the Left
stereo program are heard through and Right Front speakers and the
the center speaker. Use this mode subwoofer. It also lets you hear
whenever a music program has the stereo downmix from any DVD.
sounds you want to blend with on-
screen action or dialog.

13

0420000547 REV. B SINGLE 17 2/9/01, 1:50 PM

 Applications Guide
Playing DVD Movies: Using DVD player on TV
Using PC-DVD player on PC 1. Connect Video Out of the DVD
1. Disable the ‘Creative Multi player to Video Input of your
Speaker Surround’ (CMSS) television.
function by pressing the CMSS 2. Connect Dolby Digital com-
button until all four LEDs are pressed signal output from
off. your DVD player to the DOLBY
DIGITAL (AC-3) SPDIF IN of
For movies with Dolby your DTT2500 Digital decoder Digital
Audio
Analog
Audio

Digital 5.1 (AC-3) amplifier unit. PC-DVD ROM Drive

soundtracks: 3. Press the CMSS button until all
MPC-to-MPC CD-Audio Cable

This signal is detected auto- its three LEDs are off to

matically and the DOLBY disable the Creative Multi
DIGITAL LED lights up. You Speaker Surround (CMSS) LINE IN
CD_IN AUX_IN

will experience Dolby Digital function. MIC IN

LINE OUT

5.1 channel output. REAR OUT

For movies with Dolby

Digital 5.1 (AC-3) 4-Channel Sound Card
For two-channel movies soundtracks:
(e.g. Sound Blaster Live!)
which are Dolby Surround- This signal is detected auto-
encoded carried within the matically and the DOLBY
Dolby Digital compressed DIGITAL LED lights up. You
Dolby Digital (AC-3)
SPDIF Out
AUDIO_OUT

bitstream: will experience Dolby Digital

The Dolby Pro Logic decoder 5.1 channel output.
DOLBY DIGITAL
(AC-3) SPDIF IN
LINE IN REAR IN DIGITAL
DIN
ANALOG

INPUT
AUTO

15V
will automatically decode the SUBWOOFER
LINE OUT SPEAKER OUTPUTS
C SUBWOOFER RS LS R L
DC IN

program for 5.1 channel movie Encore Dxr2 / PC-DVD MPEG2

experience. For two-channel DVD Decoder Card (Luxsonar)
movies which are Dolby Connection Guide for DeskTop Theatre 5.1 DTT2500 Digital with Sound Blaster Live! and Creative PC-DVD system.
Surround-encoded:
The Dolby Pro Logic decoder
will automatically decode the
program for 5.1 channel movie
experience.

14

0420000547 REV. B SINGLE 18 2/9/01, 1:50 PM

 Playing VCD Movies: Using SoftMPEG player or Using VCD player on TV
Using PC-DVD player on PC PlayCenter on PC 1. Connect Video Out of the VCD
1. Disable the ‘Creative Multi 1. Select the MOVIE mode by player to Video Input of your
Speaker Surround’ (CMSS) pressing the Creative Multi television.
function by pressing the CMSS Speaker Surround (CMSS) 2. Connect the Audio Out of the
button until all four LEDs are button until the LED for VCD player to the Line In of
off. MOVIE mode lights up. your DTT2500 Digital decoder
amplifier unit.
For VCD movies with This mode lets you experience 3. Select the MOVIE mode by
Dolby Surround-encoded the surround sound with 5.1- pressing the Creative Multi
stereo program: channel output; all dialog and Speaker Surround (CMSS)
You can use the Dolby Pro central sounds will be heard button until the LED for
Logic decoder, by selecting through the center speaker, MOVIE mode lights up.
PRO LOGIC DIGITAL IN, to while music and off-stage
experience 5.1-channel movie sounds are heard through the You can experience surround
viewing. other four satellites. sound instead of mono/stereo
sound; all dialog and central
For VCD movies: If you are using PlayCenter to sounds will be heard through the
You will have Digital 2.1 play the VCDs, disable all CMSS center speaker, while music and
channel output. To enhance effects in your PlayCenter - use off-stage sounds are heard
the experience, enable the only DTT2500 Digital CMSS through the other four satellites.
Digital Pro Logic by pressing MOVIE mode.
the DOLBY SURROUND button
until the DIGITAL IN LED
lights up.

15

0420000547 REV. B SINGLE 19 2/9/01, 1:50 PM

 Playing Games: Playing Microsoft DirectSound Playing Conventional Games
Playing Multi-format DVD 3D or Environmental Audio Select MUSIC or MOVIE by
Games Games pressing the Creative Multi
These games have Dolby Digital 1. Under CMSS on your DTT2500 Speaker Surround (CMSS) button
or Dolby Pro Logic movie clips Digital decoder amplifier, select until the LED for MUSIC or
mixed with the actual game FOURPOINT to fully enjoy the MOVIE mode lights up.
sequence. 4-channel gaming experience
Select the MUSIC or MOVIE mode from Microsoft DirectSound3D
by pressing the Creative Multi or Creative Environmental
Speaker Surround (CMSS) button Audio (EA) titles with a 4-
until the LED for MUSIC or channel audio card.
MOVIE mode lights up. 2. For Sound Blaster Live! users,
enable the 4-Speaker
configuration on your PC.
Otherwise, select FourPoint
under CMSS on your DTT2500
Digital decoder amplifier unit.

16

0420000547 REV. B SINGLE 20 2/9/01, 1:50 PM

 CD Audio Music: Karaoke Music: Singing Karaoke on PC with SB
Enjoying CD Audio on PC Singing Karaoke on PC with SB Live! only (with Creative
Select the MUSIC mode by Live! and Creative PC-DVD PlayCenter)
pressing the Creative Multi Decoder Card (with Creative 1. Connect your microphone to
Speaker Surround (CMSS) button Navigator application) the MIC IN of SB Live!.
until the LED for MUSIC mode 1. Connect your microphone to 2. Enable the Microphone source
lights up. This mode creates an the MIC IN of SB Live!. in the Mixer.
enveloping five-speaker surround 2. Enable the Microphone source 3. Select one of the seven
effect that enhances stereo in the Mixer. Karaoke modes under Environ
music. 3. Select one of the seven ment in Creative Launcher.
Karaoke modes under Environ 4. Click the Audio Menu button
ment in Creative Launcher. on the Creative PlayCenter to
4. Press the AUDIO MODE button hear only the music, i.e. with
of the DTT2500 Digital the vocal portion masked out.
decoder amplifier unit until
you hear only the music i.e.
vocal portion is masked out.

17

0420000547 REV. B SINGLE 21 2/9/01, 1:50 PM

 Specifications Important Technical Support
DeskTop Theater 5.1 Playback Levels Inside U.S.A., Canada and Latin America
DTT2500 Digital DDT2500 Digital is intended for Creative Labs Inc. Technical Support
Six-channel individual or small group listening
If you need technical assistance, call 405-742-6622. Operating hours:
Amplifier Specifications and will achieve surprisingly high
(Central Time) Mon-Sat: 8am - 10pm and Sun Noon - 8pm. You can get
output levels. However, playing the
Left, Right, Left Surround, Right the latest program and driver updates from Creative Labs’ bulletin board, 24
system continuously at overly loud,
Surround amplifiers, each of hours a day. Call 405-742-6660; use modem settings:
distorted levels on heavy bass
four: 7 watts RMS per channel
program material may cause its
Baud rate: 300 to 14400
internal fuse to blow.
Center Channel amplifier: 21 (V.32/V.42 bis)
The fuse can be replaced only by
watts per channel Data bits: 8
a qualified representative. To avoid
Parity: none
this inconvenience and a possible
Subwoofer amplifier: 20 watts Stop bits: 1
non-warranty repair charge, reduce
per channel
the playback volume when the
You can also send a FAX at 405-742-6633 or write us at:
system shows obvious signs of
stress, i.e. it sounds “raspy,”
Technical Support
“fuzzy,” and/or “muddy.”
Creative Labs, Inc.
1523 Cimarron Plaza
Stillwater, OK 74075

To reach Creative Technical support via the Internet, visit our technical
support web site at http://www.creativehelp.com, for troubleshooting help.

For information about this product and other Creative Labs’ products,
visit Creative Zone at http://www.soundblaster.com. Or, call Customer
Service at 800-998-1000.

Faxback information is available by calling 405-372-5227.

18

0420000547 REV. B SINGLE 22 2/9/01, 1:50 PM

 Inside Europe Holland Tel: +3115578244
Creative Labs (Ireland) Ltd. Technical Support Italy Tel: +39 2 982 4 4100
Norway Tel: 800 11663 (Freephone)
Ballycoolin Business Park, Blanchardstown Dublin, BBS: +45 4824 4351 (HST V.34)
15 Ireland +45 4824 4361 (ZyTEL 19,200)

Ireland Tel: +353 1 820 7555 Scandinavia Tel: +45 4824 4322
Fax: +353 1 820 5052 Fax: +45 4824 4323
BBS: +353 1 820 3784 (HST) Spain Tel: 900 953536 (Freephone)
+353 1 820 3818 (ZyXEL) Sweden Tel: 020 791088 (Freephone)
Belgium Tel: +32 32300997 (French) BBS: +45 4824 4351 (HST V.34)
(for Benelux) Fax: +32 32300998 (Dutch) +45 4824 4361 (ZyTEL 19,200)
BBS: +32 3281 4631 (HST V.34) UK Tel: +44 01734 344 744
+32 3281 4632 (V.34) Fax: +44 01734 320 271
Denmark Tel: 8001 7177 (Freephone) BBS: +44 01743 360 287
BBS: +45 4824 4351 (HST V.34) Operating hours
+45 4824 4361 (V.34) Mon-Fri: Business Hours
Finland Tel: 08001 18052 (Freephone) Sat-Sun: Closed
BBS: +45 4824 4351 (HST V.34) Faxback is a facility that allows you to obtain product and technical infor-
+45 4824 4361 (ZyXEL 19,200) mation through facsimile services. In Europe, use the following number:
France Tel: +33 1 39 20 04 21 +353 1 820 3667.
Fax: +33 1 39 20 90 10
BBS: +33 1 39 20 90 43 (HST)
+33 1 39 20 90 47 (V.32bis)
Minitel: 3615 CREATIVE and 3617 CREATIVE
Germany Tel: +49 089 9579081
(for Central and Fax: +49 089 9577453
Eastern Europe) BBS: +49 089 9577274

19

0420000547 REV. B SINGLE 23 2/9/01, 1:50 PM

 1-Year Limited Warranty
Inside Asia
T
o the original purchaser, This is the sole and express
Cambridge SoundWorks, warranty. This warranty is in lieu
Creative Technology Ltd. Technical Support Inc. (a division of Creative of all other warranties, expressed
31 International Business Park, Technologies, Ltd.) will or implied, of merchantability,
Creative Resource, Singapore 609921 warrant the DeskTop Theater 5.1 fitness for purpose or otherwise.
DTT2500 Digital system to be In no event shall Cambridge
Tel: +65 8954100 free of defects in material and SoundWorks be liable for
Fax: +65 8954999 workmanship for a period of one incidental or consequential
BBS: +65 776 2423 (1) year from date of purchase. damages or have any liability
Operating Hours (Singapore Time) With respect to defects, Cam- with respect to defects other than
Mon-Thu: 9am-6:30pm bridge SoundWorks will, at its the obligations set forth as
Fri: 9am-6pm option, replace the product or stated.
Sat-Sun & Public Holidays: Closed repair the defect in the product To ensure warranty coverage, it
with no charge to the original is incumbent upon the original
purchaser for parts or labor. purchaser of DeskTop Theater 5.1
This warranty does not extend DTT2500 Digital to inform the
to any defect, malfunction or retailer of the defect within the
failure caused by misuse, abuse, warranty period. The only
accident, faulty hookup, defective acceptable method of establish-
associated equipment or use of ing warranty status is
the speaker with equipment for a copy of the original proof of
which it is not intended. purchase indicating customers
This warranty is valid only name and purchase date.
when the speaker is returned to
the retailer that sold the DeskTop
Theater 5.1 DTT2500 Digital to
the original purchaser.
© 1999 Cambridge SoundWorks, Inc. All rights reserved. Cambridge SoundWorks is a registered trademark, and PCWorks and DeskTop Theater are trademarks of Cambridge
SoundWorks, Inc., Newton, MA. The Creative logo and Sound Blaster logo are registered trademarks and the Environmental Audio logo and Creative Multi Speaker Surround are
trademarks of Creative Technology Ltd. The DeskTop Theater 5.1 DTT2500 Digital Dolby Digital Decoder Amplifier is manufactured under the license from Dolby Laboratories. “Dolby”,
“Pro Logic”, “AC-3”, and the Double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories, Inc. All rights reserved.
Microsoft and DirectSound are registered trademarks of Microsoft Inc. All other brands and product names are trademarks or registered trademarks of their respective holders. All
specifications are subject to change without prior notice. Actual contents may differ slightly from those pictured.

20

0420000547 REV. B SINGLE 24 2/9/01, 1:50 PM

0420000547 REV. B SINGLE 25 2/9/01, 1:50 PM
 311 Needham Street, Newton, MA 02464
1-800-367-4434 Fax: 617-527-3194
www.hifi.com or e-mail us at [email protected]
Rev. B
0420000547

0420000547 REV. B SINGLE 26 2/9/01, 1:50 PM