PVC-flat

300/500 V and 450/750 V

Technical data Cable structure Properties

• Special PVC-flat cable adapted to • Bare copper-conductor, to • Extensively oil resistant, oil-/ chemical
EN 50214 / DIN VDE 0283-2 DIN VDE 0295 cl.5, fine-wire, Resistance - see table Technical
Temperature range BS 6360 cl.5, IEC 60228 cl.5 Informations
flexing -5°C to +70°C • Core insulation of PVC • Extremely small bending radius
fixed installation -40°C to +80°C compound type TI2 to • High flexibility
• Nominal voltage DIN VDE 0207-363-3 / DIN EN 50363-3 • Minimum waste of space
up to 1 mm² U0/U 300/500 V • Core identification to DIN VDE 0293 • Packeting possibility
from 1,5 mm² U0/U 450/750 V - up to 5 cores coloured Tests
• Test voltage - from 7 cores, black with continuous • PVC self-extinguishing and flame retardant
up to 1 mm² 2000 V white numbering acc. to DIN VDE 0482-332-1-2,
from 1,5 mm² 2500 V • Cores laying parallel DIN EN 60332-1-2, IEC 60332-1 (equivalent
• Minimum bending radius • GN-YE conductor DIN VDE 0472 part 804 test method B)
10x cable thickness • Outer sheath of special PVC
• Radiation resistance compound type TM2 to Note
up to 80x106 cJ/kg (up to 80 Mrad) DIN VDE 0207-363-4-1/DIN EN 50363-4-1 • Part no. 27012 (6x4).
• Sheath colour black (RAL 9005) • G = with green-yellow conductor
• AWG sizes are approximate equivalent
values. The actual cross section is in mm².

Application
PVC type of flat cables are used mainly as trailing cable for crane installations, floor conveyer systems and shelf control units.
Installation notes
Cables reels with flat cables must be transported in standing position on the flange. A bending flexibility can be achieved on a plane surface. For this
purpose, the corresponding fitting instructions should be followed.
• Put the cable trolly on the guiding rail or upon carrier beam and push them together at the starting point. The distance between the bedding surface
of two cable trollys must be wider than the double thickness of a cable-packet.
• During the packeting performance, it must be started with the smaller cross section which lays on the bedding surface and will be builded successively
so that the biggest cross section is laying on the top.
• Further, be careful of a symmetrical load distribution.
• In case of multicore flat cables with small cross section, smaller than 2,5 mm², is very critical due to its low tensile stress. In such case, you should
add 10% reserve wire for calculation.
= Product conforms with EC Low-Voltage Directive 2006/95/EC.

Part no. No.cores x Outer Cop. Weight AWG-No. Part no. No.cores x Outer Cop. Weight AWG-No.
cross-sec. dimension weight app. cross-sec. dimension weight app.
mm² app. mm kg / km kg / km mm² app. mm kg / km kg / km
26980 4 G 0,75 4,3 x 12,6 28,8 90,0 19 27006 12 G 1,5 4,5 x 38,9 173,0 421,0 16
26981 5 G 0,75 4,3 x 16,1 36,0 115,0 19 27028 16 G 1,5 4,5 x 51,5 230,4 555,0 16
26982 6 G 0,75 4,3 x 19,4 43,2 141,0 19 27030 24 G 1,5 4,5 x 83,0 346,0 820,0 16
26983 9 G 0,75 4,3 x 26,4 64,8 198,0 19 27007 4 G 2,5 5,5 x 17,0 96,0 205,0 14
26984 10 G 0,75 4,3 x 30,1 72,0 224,0 19 27008 5 G 2,5 5,5 x 21,5 120,0 256,0 14
26985 12 G 0,75 4,3 x 33,8 84,4 258,0 19 27009 7 G 2,5 5,5 x 30,3 168,0 344,0 14
26986 16 G 0,75 4,3 x 44,4 115,2 340,0 19 27010 8 G 2,5 5,5 x 31,9 192,0 389,0 14
26987 18 G 0,75 4,3 x 49,2 129,6 380,0 19 27011 12 G 2,5 5,8 x 47,1 288,0 580,0 14
13.04.2016 / Dimensions and specifications may be changed without prior notice.

26988 20 G 0,75 4,3 x 55,0 144,0 424,0 19 27029 16 G 2,5 5,8 x 55,1 384,0 674,0 14
26989 24 G 0,75 4,3 x 65,6 172,8 509,0 19 27012 24 G 2,5 15,0 x 63,0 604,0 950,0 14
26990 3G1 4,5 x 10,8 28,8 80,0 18 27027 24 G 2,5 5,8 x 120,0 604,0 950,0 14
26991 4G1 4,5 x 13,4 38,4 104,0 18 27013 4G4 7,0 x 21,8 154,0 344,0 12
26992 5G1 4,5 x 16,0 48,0 134,0 18 27014 5G4 7,0 x 27,4 192,0 428,0 12
26993 6G1 4,5 x 20,6 57,6 161,0 18 27015 7G4 7,9 x 36,6 269,0 590,0 12
26994 9G1 4,5 x 28,4 86,4 230,0 18 27016 4G6 8,2 x 24,8 230,0 424,0 10
26995 10 G 1 4,5 x 30,0 96,0 256,0 18 27017 5G6 8,2 x 31,8 288,0 530,0 10
26996 12 G 1 4,5 x 36,2 115,2 298,0 18 27018 7G6 8,2 x 42,6 403,0 760,0 10
26997 16 G 1 4,5 x 47,6 153,6 395,0 18 27019 4 G 10 10,0 x 29,6 384,0 710,0 8
26998 18 G 1 4,5 x 52,8 172,8 441,0 18 27020 4 G 16 11,2 x 34,4 614,0 1014,0 6
26999 20 G 1 4,5 x 59,0 192,0 495,0 18 27025 5 G 16 13,0 x 46,6 768,0 1370,0 6
27000 24 G 1 4,5 x 70,4 230,4 590,0 18 27021 4 G 25 13,7 x 42,6 960,0 1365,0 4
27001 4 G 1,5 4,5 x 13,7 58,0 133,0 16 27026 5 G 25 15,5 x 55,5 1200,0 2000,0 4
27002 5 G 1,5 4,5 x 17,9 72,0 169,0 16 27022 4 G 35 15,4 x 47,6 1344,0 2100,0 2
27003 7 G 1,5 4,5 x 23,5 101,0 235,0 16 27023 4 G 50 18,2 x 57,0 1920,0 2940,0 1
27004 8 G 1,5 4,5 x 26,8 115,0 265,0 16 27024 4 G 70 20,0 x 64,2 2688,0 4090,0 2/0
27005 10 G 1,5 4,5 x 33,5 144,0 332,0 16

Dimensions and specifications may be changed without prior notice. (RJ01)