IBSC_Know-Your-Steel_V9_June2023

Know Your Steel
Steel Mass Reference and Product Catalogue

JUNE 2023 | Edition 9
Hot Rolled Structural | Tubular | Merchant Bar | Pipe & Fittings | Plate | Sheet
Reinforcing Mesh & Bar | Aluminium | Building Products | Fencing
Rural Products | Roofing & Rainwater | Accessories
infrabuild.com
KNOW YOUR STEEL
Know Your Steel Mass Book
Foreword • Stramit Corporation Pty Ltd (ABN 57 005 010 195) - Speed
Deck Ultra, Corrugated, Monoclad, Megaclad, Longspan,
This publication has been prepared by InfraBuild Steel Centre Capacity Plus, Minirib, Mini Corry, PrimeForm, Edge Forma
which is an operating business of InfraBuild Trading Pty • Illinois Tool Works Inc (ABN 48 052 404 092) - Galmet, Buildex,
Limited (ABN 50 007 519 646). The aim of this booklet is to Teks, Shed Teks, Ripple Teks, AutoTeks, SuperTEKS, RoofZips,
provide customers with useful information regarding steel and Hi-Teks, BattenZips, PolyZips, Pryda
accessory products. Every effort has been made to ensure
that the information contained in this publication is accurate.
However, it should be noted that the company cannot accept Range
responsibility for errors or omissions, or for changes which have
taken place since the printing of this edition. Unless required PLEASE NOTE:
by law, the company cannot accept any responsibility for • The product ranges shown in this book are an indicative
any loss, damage or consequence resulting from the use of range only.
this publication. The preferred range of sizes only has been
covered, some of these sizes may be subject to minimum • Some items may be subject to minimum order quantities.
order quantities, and every care should be taken to establish Sources Of Information
availability before proceeding based on the specifications
provided. Additional information concerning non-preferred • Liberty Steel - Product and Availability Guide -
sizes, range of specifications available, or related data not
Section Foreward
| header
Hot Rolled Structural Steel

included in this booklet is available on request through
InfraBuild Steel Centre Branches. • InfraBuild Steel - Pricing and Availability Guide -
Merchant Bar
NOTE: Mass Calculations have been based on a mass for • Austube Mills - Product and Availability Guide -
carbon steel of 7,850 kg/m3 rounded off and includes Pipe and Tube Structural Products
a 2.5 per cent rolling tolerance where applicable. • InfraBuild Reinforcing Product Guide
• BlueScope Steel Hot Rolled Price Schedule
Trademarks • BlueScope Steel Xlerplate Price Schedule
• BlueScope Steel Xlerplate Lite Schedule
• Austube Mills Pty Ltd (ABN 21 123 666 679) - DuraGal,
DuraGalClear, DuraPrimed, C450Plus • BlueScope Steel - Aluminium Catalogue
• BlueScope Steel - Steel Guide
• OneSteel Manufacturing Pty Ltd - 300PLUS
• InfraBuild Trading Pty Limited (ABN 50 007 519 646) - DuraGal
Flooring System Terms & Conditions Of Sale
• InfraBuild Reinforcing Pty Limited (ABN 22 004 148 289) -
HANDIMESH, ONEMESH, 500PLUS, UTEMESH A full copy of InfraBuild Terms & Conditions of Sale is located
at: www.infrabuild.com
• BlueScope Steel Limited (ABN 16 000 011 058) - TruSpec,
Xlerplate, Xlerplate Lite, Brightform, Blackform, Galvabond,
Galvaskin, Zincanneal, Zincalume, Colorbond, LY-TEN, Lysaght,
Longline 305, Multiclad, Easyclad, Quad 115 Hi Front, Trimline,
Sheerline, Emline, Half Round, Ranceline, Colonial, Novaline,
Bondek, W-Dek, Neetascreen, Smartascreen, Miniscreen,
Customscreen, Flatdek, Flatdek II, Firmlok, Headland, Manor
Red, Jasper, Sandbank, Classic Cream, Surfmist, Paperbark,
Dune, Shale Grey, Windspray, Woodland Grey, Bushland, Pale
Eucalypt, Wilderness, Cottage Green, Plantation, Blue Ridge,
Deep Ocean, Night Sky
• Bisalloy Steels Pty Ltd (ABN 27 001 641 292) - Bisalloy® Wear,
Bisalloy® Structural
Steel Centre
Note: InfraBuild Steel Centre reserve the right to change specifications without notice. Not all products are available at all InfraBuild Steel
Centre branches. InfraBuild Steel Centre also has access to a wide network of products not necessarily listed in this book. Please check with
your local InfraBuild Steel Centre branch for product availability.
Note: InfraBuild Steel Centre reserve the right to change specifications without notice. Not all products are available at all InfraBuild Steel Centre branches. InfraBuild Steel
Centre also has access to a wide network of products not necessarily listed in this book. Please check with your local InfraBuild Steel Centre branch for product availability.
2
KNOW YOUR STEEL
Our Purpose Engineering &
Design Optimisation
We exist to build our customers' possibilities: to make their
businesses stronger and more prosperous; to make their trucks As part of the broader InfraBuild and Liberty Steel group of
and caravans safer; to assist their farms to be more productive; businesses, InfraBuild Steel Centre can draw on significant
to contribute to more sustainable and secure futures. From expertise to provide engineering and design optimisation
large projects to small, those that build our nation and our solutions for our customers. Optimising materials for
communities, we partner with customers to build the businesses construction can assist with minimising risk while reducing
we work in and the homes we live in. We help our customers waste and cost, and can also contribute to the sustainability
to fulfil their ambitions with peace of mind that comes from credentials required for awarding Green Star® credit points.
quality, compliant and traceable product supply and service
solutions.
Our Processing Services
We Understand • Profile Cutting • Tapping
InfraBuild Steel Centre is Australia's largest vertically-integrated • Oxy Cutting • Slotting
steel distribution business. With our extensive steel product • Plasma Cutting • Coping
knowledge and experience, our team helps our customers to
• Flame Cutting • Bevelling
find solutions to deliver the right outcomes for large or small
Foreward
projects, as well as ongoing steel supply requirements. • Stitch Cutting • Penetrations
• Punching • Counter Boring
We Make It Easier • Drilling • Counter Sinking
• Shearing • Cut to Length
InfraBuild Steel Centre is backed by a national and international • Stamping • Pack Cutting
supply network to ensure our customers receive the best level
of service to support their needs. Our wide-ranging in-house • Notching • Cambering
processing capability reduces complexity for our customers to • Marking
reliably deliver on one-off and repeatable requirements with
accuracy to add value.
Compliance & Traceability
We Deliver InfraBuild supplies products that are compliant with relevant
Australian Standards. The quality of our products are
InfraBuild Steel Centres' comprehensive branch and delivery
checked by NATA endorsed testing laboratories. At all of our
network allows us to deliver to our customers how and when
manufacturing sites, InfraBuild has third party accreditation
they want to receive product. Our integrated supply chain and
to Quality Management System ISO 9001 and Environmental
network of industry partners means we can source a range of
Management System ISO 14001. In addition, our hot rolled
product to complement projects and deliver a complete supply
products are all produced at mills with ACRS third party
solution.
accreditation ensuring certification for reinforcing, pre-stressing
and structural steels. InfraBuild Steel Centre also supports the
Our Products Build With Standards initiative undertaken by InfraBuild which
aims to improve compliance and generate confidence in the
Our range includes structural and tubular steel, reinforcing quality, identification, certification and traceability of structural
and merchant bar, sheet and plate as well as pipes, valves and and reinforcing steels. Further information can be found at
fittings, flooring systems, rollform products, aluminium and a www.infrabuild.com
huge range of complementary products and accessories. We
also have the ability to source local and international products
with short lead times.
Steel Centre
Hot Rolled Structural | Tubular | Merchant Bar | Pipe & Fittings | Plate | Sheet
Reinforcing Mesh & Bar | Aluminium | Building Products | Fencing
Rural Products | Roofing & Rainwater | Accessories
3
Sustainable Products
KNOW YOUR STEEL
The Infrastructure Sustainability Council’s (ISC)

IS Rating Scheme.
Under Both Versions
Up to three points are available to reward design and practice
that reduces life cycle impacts via reduced material use such as
Prefabricated Reinforcing Elements, Engineered Reinforcing Bar
Carpet (BAMTEC®) or Engineered Mat (BARMAT®).
ISC aims to improve the productivity and liveability of industry Up to three points are available to reward environmentally
and communities through sustainability in infrastructure. ISC labelled products and supply chains:
developed and administers the Infrastructure Sustainability (IS) • One point is available via the use of products covered by
Rating Scheme. our EPDs
The IS scheme is Australia’s only comprehensive rating system • Two additional points are available if >9% of materials/
for evaluating sustainability across design, construction and products (by value) have an ISC- approved environmental
operation of infrastructure. label, such as InfraBuild’s EPD.
The scheme evaluates the sustainability (including environmental,
social, economic and governance aspects) of infrastructure Sustainability Outcomes
projects and assets. InfraBuild publishes Environmental Product Declarations (EPDs)
There are two versions of the IS materials calculator. Projects will that cover our hot-rolled steel, reinforcing bar and reinforcing
Section | Products
header
be awarded an IS Rating based on an overall score: mesh products. InfraBuild EPDs may help your project achieve
credits with ISv2.0 and ISv1.2.
ISv1.2 InfraBuild also publishes Corporate Sustainability reports.
There are up to 7 points available under the materials category; 6
Sustainable
InfraBuild has a range of policies and procedures that

points for the materials calculator and 1 point for environmentally demonstrates strong social, economic, safety and environmental
labelled products. credentials, which may contribute to additional IS credits such as
ISv2.0 Lea-1, Lea-2, Lea-3, Inn-1 Spr-2, Spr-3, Rso-4, Rso-6, Wfs-4
ISv1.2 (L3.4), Ecn-1 and Ecn-4 and ISv1.2 Mat-1, Mat-2, Pro-2, Pro-4,
Points Rating Level Was-1, Was-2, Was-3.
25 – 49+ Commended Early collaboration with InfraBuild fosters opportunities for
innovation, reduced environmental impacts, risk minimisation,
50 – 74+ Excellent knowledge sharing, offsite fabrication, design and logistics
75+ Leading optimisation and waste minimisation, as well as broader supply
chain engagement contributing to the above credits.
Related ISv1.2 Credits InfraBuild’s products are all manufactured to the relevant
Mat-1, Mat-2, Pro-2, Pro-4, Was-1, Was-2, Was-3 Australian Standards. InfraBuild has ACRS Certification for
our reinforcing products, which further underpins our strong
Rating Phases: As Built, Design, Planning
compliance credentials.
Our product traceability and transparency through the supply
ISv2.0 chain provides confidence to the market that the material
supplied meets the design, quality and sustainability specifications
There are up to 6 points available under the materials category:
of the project.
4.5 points for the materials calculator and 1.5 points for
environmentally labelled products. Read more about the IS Rating Scheme at the ISC website
(https://www.iscouncil.org/).
ISv2.0
Points Rating Level
25 – 39 Bronze
40 – 59 Silver
60 – 79 Gold
80 – 94 Platinum
95+ Diamond
Related ISv2.0 Credits

Ecn-1, Ecn-4, Inn-1, Lea-1, Lea-2, Lea-3, Rso-4,
Steel Centre
Rso-5, Rso-6, Rso-7, Spr-2, Spr-3, Wfs-4

As Built, Design, Operations
4
Green Star®
KNOW YOUR STEEL

Steel Credit Points
The Green Building Council of Australia (GBCA) Responsible Building Materials Credit 20.1A – Points
is a national authority on sustainable buildings, available: 1
communities and cities. • One point is available where 95% of the building’s steel (by
mass) is sourced from a responsible steel maker and at
least 60% (by mass) of the fabricated structural steelwork
is supplied by a steel fabricator / steel contractor
accredited to the Environmental Sustainability Charter of the
Australian Steel Institute.
• The GBCA administers the Green Star® environmental rating • InfraBuild meets the two requirements of being a
system for commercial, residential, industrial, healthcare and “Responsible Steel Maker” by having
education buildings.
In Australia, Green Star® is a trusted mark of quality for the i) A currently valid and certified ISO 14001
design, construction and operation of sustainable buildings, Environmental Management System (EMS) in place
fit-outs and communities ii) Membership of the worldsteel Climate Action Program
• Green Star® ratings are utilised by the majority of CBD Certification to demonstrate the above is available from
commercial multi-storey developments and government the InfraBuild website.
projects
• In 2017, the Green Building Council of Australia updated its Sustainable Products – Credit 21
Design and As Built Guidelines.
• Up to three (3) points are available when project teams can
Green
• The following lists the Steel Credit points that may be
Section
demonstrate that a specified percentage of eligible products
available through using InfraBuild's products under the current meet one of the following initiatives:
guidelines v1.3:
A. Reused Products, in accordance with 21A
Star| ®Header
Points under D&AB Tool B. Recycled Content Products, in accordance with 21B
Points Rating Outcome C. Environmental Product Declarations, in accordance with 21C
Steel Credit Points

45 – 59 Four Star Australian Best Practice D. Third-Party Certification, in accordance with 21D, or
60 – 74 Five Star Australian Excellence E. Stewardship Programs, in accordance with 21E.
75+ Six Star World Leadership
Points are awarded based on the percentage value of the
Life Cycle Impacts – Steel Credit 19B.2B – Points products that meet one of the specified initiatives. This is
available: 1 demonstrated by calculating the Project Sustainability Value (PSV)
• One point is available where project teams can demonstrate and comparing it with the Project Contract Value (PCV) as
a reduction in the mass of steel framing used in the building a percentage.
when compared to standard practice.
There are available pathways to achieving this Credit; InfraBuild can help achieve the Green Star® steel credit
A.19B.2A.A – through the use of a minimum proportion of high requirements in the following ways:
strength steel • InfraBuild Steel Centre sources a range of products from mills
with a valid ISO 14001 Environmental Management System
B.19B.2A.B – by demonstrating that the project results in a 5%
or more reduction in mass of steel framing, when compared to a • InfraBuild Steel Centre sources a range of products from mills
suitable reference case building. with membership of the worldsteel Climate Action Programme
• InfraBuild Steel Centre can assist in Credit 21 of the GBCA
Green Star scheme
For more information on Green Star® related products visit
the Green Star page of our website.
Steel Centre
5
KNOWYOUR
KNOW STEEL
YOURSTEEL
National Branch Network

InfraBuild Steel Centres' extensive national branch network provides solutions for our
customers, wherever they need them.
DARWIN
Branch| Network
header
MACKAY
KARRATHA EMERALD ROCKHAMPTON
GLADSTONE
SUNSHINE COAST
Section
TOOWOOMBA
BRISBANE
YATALA, GOLD COAST
National
LISMORE
GERALDTON
KALGOORLIE
LANDSDALE, COFFS HARBOUR
MIDVALE,
BIBRA LAKE TAMWORTH
NORTHAM NEWCASTLE
WELSHPOOL DUBBO
PERTH SILVERWATER
WAGIN WHYALLA WETHERILL PARK SYDNEY
MANDURAH PENRITH
MILDURA
WOLLONGONG
BUNBURY PORT ADELAIDE CANBERRA
HORSHAM
MOUNT GAMBIER SHEPPARTON ALBURY
BENDIGO
MELBOURNE
InfraBuild Steel Centre LOCATIONS

LAUNCESTON
MIDALIA STEEL LOCATIONS
InfraBuild Steel Centre / MIDALIA LOCATIONS
HOBART
Safety at Our Sites

At InfraBuild we have set ourselves a safety goal of < 2 TRIFR (Total Recordable Injury Frequency Rate)
by 2025. We have a roadmap to get us there called – WRIB Safe. All of our safety actions and behaviours
are underpinned by our ‘Be GFG Safe’ global strategy to ensure every employee returns home fit and well
at the end of each workday. By working together as one team, with respect for one another, we build our
safety culture. We take the time to do things safely, to intervene, and to speak up when we notice a risk or
hazard. At InfraBuild, we believe one injury is one too many.
We appreciate your compliance with our safety policies when you visit our sites.
Steel Centre
Hot rolled structural | tubular | merchant bar | pipe & fittings | plate | sheet
reinforcing mesh & bar | aluminium | building products | fencing
rural products | roofing & rainwater | accessories
6 www.Infrabuild.com
KNOW
KNOW YOUR
YOUR STEEL
STEEL
Our Valued Supply Partners
InfraBuild Steel Centre stock and supply quality products from suppliers and brands our
customers know and trust.
Building future s thro ug h sustainab le ste e l
Our
Section
Valued
| Header
Supply Partners
®
Steel Centre
Note: InfraBuild Steel Centre reserve the right to change specifications without notice. Not all products are available at all InfraBuild Steel
Centre branches. InfraBuild Steel Centre also has access to a wide network of products not necessarily listed in this book. Please check with your
local InfraBuild Steel Centre Branch for product availability.
7
Contents
KNOW YOUR STEEL
Structural Sheet and Coil Building Products

Equal Angles 10 BRIGHTFORM® Sheet 55 DuraGal Flooring System® 85
Unequal Angles 10 Hot Rolled Sheet 56 DuraGal® Mezzanine Flooring System 85
Universal Beams 11 Hot Rolled, Pickled and Oiled Sheet 56 Lintels – Traditional 86
Welded Beams 11 Cold Rolled Sheet 57 Lintels – Flat and Angle 87
Taper Flange Beams 12 GALVABOND® Sheet 58 C-Purlins 90
Universal Columns 13 ZINCANNEAL® Sheet 59 Z-Purlins 90
Welded Columns 13 ZINCALUME® Sheet 60 Battens, Roofing and Walling 92
Parallel Flange Channels 14 COLORBOND® Sheet 61 Flashings 94
Rails 14 COLORBOND® Steel Colour Range 94
Rainwater Products 95
Reinforcing Bar and Mesh Structural Products 97
Bar Sections Gutters and Fascia 97
HANDIMESH® 62
Structural Decking 97
Equal Angles 16 UTE MESH® 62
Fencing 98
Unequal Angles 17 ONEMESH® 62
Flat Bars – Round Edge 17 Plain Square Mesh 63
Flat Bars – Square Edge 18 Trench Mesh 63 Piping Systems
Round Bars 21 Deformed Reinforcing Bar 64
Square Bars 22 Reinforcing Accessories 65 Steel Pipes to American Standards 99
Parallel Flange Channels 22 Stainless Steel Pipes to American Standards 101
Contents
Billets 23 Carbon Steel Buttweld Fittings 101

DuraGal® Channels 23 Aluminium Flanges to American Standards 102
DuraGal® Angles 24 Bolting for ANSI Flanges 103
Aluminium Circular Tube 66
DuraGal® Flat Bars 26 Buttweld Fittings and Flanges to ASME
Aluminium Rectangular Tube 67 Standards 104
Aluminium Square Tube 68 Flanges to Australian Standards 105
Tubular Aluminium Angles 69 ISO Metric Hexagon Steel Bolts 106
Aluminium Channels 70
Square Hollow Sections (SHS) 27 Aluminium Tees 71
Rectangular Hollow Sections (RHS) 29 Aluminium Round Bars 71 Fencing and Fittings
Stock Rail and Posts 32 Aluminium Flat Bars 72
Silo Sections 32 Aluminium Square Bars 72 Fabricated Fencing 107
Stock Rail Accessories 33 Aluminium Sheet and Plate 73 Fence Wire 108
Circular Hollow Sections (CHS) 33 Trellis Wire 108
Structural CHS 39 Tie Wire 109
Telescoping RHS 41 Stainless Steel Barbed Wire 109
Telescoping SHS 42 Netting 109
Stainless Steel Angles 75 Posts 111
Telescoping CHS 44
Stainless Steel Sheet and Coil 75 Gates 112
End Colour Codes 46
Stainless Steel Flat Bars 76 Fittings, Clamps, Hinges and Gudgeons 113
Stainless Steel Round Bars 77
Plate
Fasteners
Flat Plate G250 47 Walkway Systems
Flat Plate G350 49 Fasteners 115
Grating and Flooring 78
K1042 Plate 50
Stair Stringers 79
Pressure Vessel Plate 50
Floor Plate G250 51
Stair Treads 80 General Information
Non-Weld Handrail Systems 81
Coil Plate HA250 51
Geometry and Mensuration 116
Floor Plate HA250 52
Gauge Conversions 116
Coil Plate HA350 52
Conversion Tables 117
Wear Plate 53
Useful Conversion Factors 118
Structural Plate 54
Handy Tips 120
Relevant Australian Standards 121
Steel Centre
8
KNOW YOUR STEEL
300PLUS® structural steel | C450PLUS™ structural tube
It's all About Integrity

In April 2016, revisions to four Australian
Standards and two Technical Specifications
covering structural steels were released by
Standards Australia.
These releases address increasing concerns in the construction industry about
the non-compliance of building materials and the risk they pose to the industry
and the community generally. Specifying and procuring compliant product
reduces your professional risk and the safety risk to the community. Projects
that specify these new Standards and Technical Specifications will be in a better
position to manage the risk that would otherwise exist.
The following mandatory The four Standards are: The two Technical Specifications:
requirements in the Australian • AS/NZS 1163-2016 – Cold-formed • SA TS 102-2016 – Structural steel –
Standards provide you with structural steel hollow sections Limits on elements added
confidence you are getting
• AS/NZS 3678-2016 Structural steel • SA TS 103-2016 – Welding to AS/
quality and compliant steel
– Hot rolled plates, floorplates and NZS 1554 Parts 1, 5 and 7– Limits
products:
slabs on boron in parent materials
Minimum specific information • AS/NZS 3679.1-2016 – Structural
on Test Certificates: steel – Part 1: Hot-rolled bars and
sections
• Testing to be performed by
laboratories with third party • AS/NZS 3679.2-2016 – Structural
accreditation from NATA steel – Part 2: Welded I sections
• Individual length identification
markings
Steel Centre
9
Structural
KNOW YOUR STEEL
Equal Angles
Various Standard Lengths
Size Mass Metres

mm × mm × mm kg/m per tonne
125 x 125 x 8 14.9 67

125 x 125x 10 18.0 56
125 x 125 x 12 22.5 44
125 x 125 x 16 29.1 34
150 x 150 x 10 21.9 46
150 x 150 x 12 27.3 37
150 x 150 x 16 35.4 28
150 x 150 x 19 42.1 24
200 x 200 x 13 40.0 25
Note: See page 14 for
200 x 200 x 16 48.7 21 Merchant Bar Equal Angles.
200 x 200 x 18 54.4 18
200 x 200 x 20 60.1 17
200 x 200 x 26 76.8 13
Angles
Typical Uses: Features:

• Engineering Construction • Meets AS/NZS 3679.1:2016
|
Structural
• Residential Construction • Up to 20% stronger for improved

• Non-Residential strength to weight ratios
Construction • Requires no special pre-heating
• Mining Infrastructure for welding
• Transport and Storage
• Manufacturing
Unequal Angles
Size Mass Metres

150 x 90 x 8 14.3 70
150 x 90 x 10 17.3 58
150 x 90 x 12 21.6 46
150 x 90 x 16 27.9 36
150 x 100 x 10 18.0 56
150 x 100 x 12 22.5 44

• Residential Construction • Up to 20% stronger for improved Merchant Bar Unequal Angles.
Steel Centre

• Manufacturing
10
KNOW YOUR STEEL
Universal Beams
Metric Size Mass Metres

Designation mm x mm kg/m per tonne
150 UB 150 x 75 14.0 71
150 UB 155 x 75 18.0 56
180 UB 173 x 90 16.1 62
180 UB 175 x 90 18.1 55
180 UB 179 x 90 22.2 45
200 UB 198 x 99 18.2 55
200 UB 202 x 133 22.3 45
200 UB 203 x 133 25.4 39
200 UB 207 x 134 29.8 34
250 UB 248 x 124 25.7 39
250 UB 252 x 146 31.4 32 Typical Uses:
250 UB 256 x 146 37.3 27
• Engineering Construction
310 UB 298 x 149 32.0 31
• Residential Construction
310 UB 304 x 165 40.4 25
Structural
• Non-Residential
310 UB 307 x 166 46.2 22
Construction
360 UB 352 x 171 44.7 22
• Mining Infrastructure
360 UB 356 x 171 50.7 20
360 UB 359 x 172 56.7 18
|
• Manufacturing
410 UB 403 x 178 53.7 19
Beams
410 UB 406 x 178 59.7 17
460 UB 454 x 190 67.1 15 Features:
460 UB 457 x 190 74.6 13
• Meets AS/NZS 3679.1:2016
460 UB 460 x 191 82.1 12
• Up to 20% stronger
530 UB 528 x 209 82.0 12 for better strength to
530 UB 533 x 209 92.4 11 weight ratios
610 UB 602 x 228 101 10 • Requires no special
610 UB 607 x 228 113 9 pre-heating for welding
610 UB 612 x 229 125 8
Structural Processing
InfraBuild Steel Centre can offer processing for Structural Steel sections using a variety
of machinery including Beamlines, Band Saws and Cambering Machines.
Applications include: Straight cuts, pack cuts, mitre cutting, drilling and cambering.
Steel Centre
Call your local branch to discuss your requirements
11
KNOW YOUR STEEL
Welded Beams
Metric Mass Size Metres

Designation kg/m mm x mm per tonne
700 WB 115 692 x 250 8.70

700 WB 130 700 x 250 7.69
700 WB 150 710 x 250 6.67
700 WB 173 716 x 275 5.78
800 WB 122 792 x 250 8.20
800 WB 146 800 x 275 6.85
800 WB 168 810 x 275 5.95
800 WB 192 816 x 300 5.21
900 WB 175 900 x 300 5.71
900 WB 218 910 x 350 4.59
Typical Uses:
900 WB 257 916 x 400 3.89 • Engineering Construction
900 WB 282 924 x 400 3.55 • Residential Construction
1000 WB 215 1000 x 300 4.65 • Non-Residential
Beams
1000 WB 258 1010 x 350 3.88 Construction

1000 WB 296 1016 x 400 3.38 • Mining Infrastructure
|
1000 WB 322 1024 x 400 3.11

• Manufacturing
Structural
1200 WB 249 1170 x 275 4.02

1200 WB 278 1170 x 350 3.60
1200 WB 317 1176 x 400 3.15 Features:
1200 WB 342 1184 x 400 2.92 • Meets AS/NZS 3679.2:2016
1200 WB 392 1184 x 500 2.55 • Up to 20% stronger for
1200 WB 423 1192 x 500 2.36 improved strength
1200 WB 455 1200 x 500 2.20 to weight ratios
• Requires no special pre-
Note: Made to order. Lead times may apply. heating for welding
Taper Flange Beams

Size Mass Metres

100 x 45 7.20 139

125 x 65 13.1 76

• Non-Residential
Steel Centre
Construction
Manufacturing
12
KNOW YOUR STEEL
Universal Columns

100 UC 14.8 97 x 99 68
150 UC 23.4 152 x 152 43
150 UC 30.0 158 x 153 33
150 UC 37.2 162 x 154 27
200 UC 46.2 203 x 203 22
200 UC 52.2 206 x 204 19
200 UC 59.5 210 x 205 17
250 UC 72.9 254 x 254 14
250 UC 89.5 260 x 256 11
310 UC 96.8 308 x 305 10
310 UC 118 315 x 307 8
310 UC 137 321 x 309 7
310 UC 158 327 x 311 6
Structural
• Residential Construction • Up to 20% stronger for better strength
|
to weight ratios
Columns
• Non-Residential
• Manufacturing
Welded Columns

350WC 197 331 x 350 5.08
350WC 230 339 x 350 4.35
350WC 258 347 x 350 3.88
350WC 280 355 x 350 3.57
400WC 144 382 x 400 6.94
400WC 181 390 x 400 5.52
400WC 212 400 x 400 4.72
400WC 270 414 x 400 3.70
400WC 303 422 x 400 3.30
400WC 328 430 x 400 3.05 Features:
400WC 361 430 x 400 2.77
• Meets AS/NZS 3679.2:2016
500 WC 228 490 x 500 4.39
500 WC 267 500 x 500 3.75
Note: Made to order.
Steel Centre
500 WC 290 506 x 500 3.45 Lead times may apply.

500 WC 340 514 x 500 2.94
500 WC 383 472 x 500 2.61
500 WC 414 480 x 500 2.42
500 WC 440 480 x 500 2.27
13
KNOW YOUR STEEL
Parallel Flange Channels

Size Mass Metres

150 × 75 17.7 56.5
180 × 75 20.9 47.8
200 × 75 22.9 43.7
230 × 75 25.1 39.8
250 × 90 35.5 28.2
300 × 90 40.1 24.9
380 × 100 55.2 18.1

• Residential & Non- • Up to 20% stronger for improved Note: See page 20 for
Residential Construction Small Channel Sections.
strength to weight ratios.
• Requires no special pre-heating
Channels and Rails
• Transport and Storage for welding.

• Manufacturing
Rails
|
Structural
Mass Metres
Section
kg/m per tonne
10 10.1 99.0
15 15.2 65.8
22 22.3 44.8
30 30.1 33.2
41 40.8 24.5
50 50.7 19.8
53 53.0 18.9
60 60.7 16.5
68 67.5 14.8
73 73.6 13.9
Note: Rails are not normally a stocked
86 85.5 11.7 item, lead times may apply.
Rely on the strength of 300PLUS®

• Manufactured in Australia by Liberty Steel
• Available across the entire Merchant Bar and Structural Steel Ranges
Steel Centre
• Up to 20% extra strength – improved strength to weight ratios mean your constructions can
save weight, as well as money
• Can be readily welded without requiring special pre-heating
14
Steel Centre
Processing Solutions
At InfraBuild Steel Centre we make it easier with steel supplied and
processed in one place. With processing equipment owned and operated
by InfraBuild Steel Centre, you can consult our team at every stage of your
project to manage your processing requirements. Whether it's accuracy,
tolerance or repeatability you need, we can help you achieve this through
our fully-programmable machinery and the extensive experience of our
people. Our industry knowledge and national support network ensures you
and your projects receive the highest level of service and support.
Bar Sections
KNOW YOUR STEEL
Equal Angles
Size Mass Metres

25 x 25 x 3 1.12 893
25 x 25 x 5 1.65 606
25 x 25 x 6 2.08 481
30 x 30 x 3 1.35 741
30 x 30 x 5 2.01 498
30 x 30 x 6 2.56 391
40 x 40 x 3 1.83 546
40 x 40 x 5 2.73 366
40 x 40 x 6 3.50 286
50 x 50 x 3 2.31 433
50 x 50 x 5 3.48 287
50 x 50 x 6 4.46 224 Note: See page 8 for
50 x 50 x 8 5.68 176 Structural Angles.
Equal Angles
55 x 55 x 5 3.84 260
55 x 55 x 6 4.93 203
65 x 65 x 5 4.56 219
65 x 65 x 6 5.87 170
65 x 65 x 8 7.51 133
65 x 65 x 10 9.02 111
|
Bar Sections
75 x 75 x 5 5.27 190
75 x 75 x 6 6.81 147
75 x 75 x 8 8.73 115
75 x 75 x 10 10.5 95
90 x 90 x 6 8.22 122
90 x 90 x 8 10.6 94
90 x 90 x 10 12.7 79
100 x 100 x 6 9.16 109
100 x 100 x 8 11.8 85
100 x 100 x 10 14.2 70
100 x 100 x 12 17.7 56

Construction
• Manufacturing
Steel Centre
16
KNOW YOUR STEEL
Unequal Angles
Size Mass Metres

65 x 50 x 5 4.02 249
65 x 50 x 6 5.16 194
65 x 50 x 8 6.59 152
75 x 50 x 5 4.40 227
75 x 50 x 6 5.66 177
75 x 50 x 8 7.23 138
100 x 75 x 6 7.98 125
100 x 75 x 8 10.3 97
100 x 75 x 10 12.4 81
125 x 75 x 6 9.16 109
125 x 75 x 8 11.8 85
125 x 75 x 10 14.2 70 Note: See page 8 for
125 x 75 x 12 17.7 57 Structural Angles.
Bar Sections
|
Construction
Unequal Angles
• Manufacturing
Flat Bars - Round Edge

Standard Length 4.0m
Size Mass Metres

10 x 3 0.25 4000
13 x 3 0.32 3125
13 x 5 0.53 1887
13 x 6 0.65 1538
16 x 3 0.40 2500
16 x 5 0.66 1515
16 x 8 1.06 943

• Engineering Construction • Meets AS/NZS 3679.1:2016 Note: Mass Calculations include a
• Residential Construction 2.5 per cent rolling tolerance for this
• Requires no special pre-heating product.
• Non-Residential for welding
Construction
Steel Centre
• Manufacturing
17
KNOW YOUR STEEL
Flat Bars - Square Edge

Size Mass Metres

20 x 3 0.48 2083
20 x 5 0.81 1235
20 x 6 0.96 1042
20 x 10 1.61 621
25 x 3 0.60 1667
25 x 5 1.00 1000
25 x 6 1.21 826
25 x 8 1.61 621
25 x 10 2.01 498
25 x 12 2.42 413
32 x 3 0.77 1299
32 x 5 1.29 775
32 x 6 1.55 645 Typical Uses:
32 x 8 2.06 485
32 x 10 2.57 389
32 x 12 3.09 324
40 x 3 0.96 1042
• Non-Residential
Construction
40 x 5 1.61 621
40 x 6 1.93 518
40 x 8 2.57 389
40 x 10 3.22 311 • Manufacturing
40 x 12 3.86 259
40 x 16 5.15 194 Features:
|
Bar Sections
40 x 20 6.44 155
• Meets AS/NZS 3679.1:2016
50 x 3 1.21 826
• Up to 20% stronger for
50 x 5 2.01 498
improved strength to
50 x 6 2.42 413 weight ratios
50 x 8 3.22 311
50 x 10 4.03 248 heating for welding
50 x 12 4.83 207
50 x 16 6.44 155
Note: Mass Calculations include a
50 x 20 8.05 124 2.5 per cent rolling tolerance for this
50 x 25 10.1 99 product.
65 x 3 1.57 637
65 x 5 2.61 383
65 x 6 3.14 318
65 x 8 4.18 239
65 x 10 5.23 191
65 x 12 6.27 159
65 x 16 8.36 120
65 x 20 10.5 95
65 x 25 13.1 76
75 x 5 3.01 332
75 x 6 3.62 276
75 x 8 4.83 207
Steel Centre
75 x 10 6.04 166
18
KNOW YOUR STEEL
Size Mass Metres

75 x 12 7.25 138
75 x 16 9.66 104
75 x 20 12.1 83
75 x 25 15.1 66
90 x 5 3.62 276
90 x 6 4.35 230
90 x 8 5.79 173
90 x 10 7.25 138
90 x 12 8.69 115
100 x 5 4.03 248
100 x 6 4.83 207
100 x 8 6.44 155
100 x 10 8.05 124 Typical Uses:
100 x 12 9.66 104
Bar Sections
100 x 16 12.9 78
100 x 20 16.1 62
100 x 25 20.1 50
• Non-Residential
Construction
100 x 50 40.3 25
110 x 6 5.31 188
|
110 x 8 7.08 141

110 x 10 8.86 113 • Manufacturing
110 x 12 10.7 93
130 x 5 5.23 191 Features:
130 x 6 6.27 159
• Meets AS/NZS 3679.1:2016
130 x 8 8.36 120
• Up to 20% stronger for
130 x 10 10.5 95
improved strength to
130 x 12 12.5 80 weight ratios
130 x 16 16.7 60
130 x 20 20.9 48 heating for welding
130 x 25 26.1 38
150 x 5 6.04 166
Note: Mass Calculations include a
150 x 6 7.25 138 2.5 per cent rolling tolerance for this
150 x 8 9.66 104 product.
150 x 10 12.1 83
150 x 12 14.5 69
150 x 16 19.3 52
150 x 20 24.2 41
150 x 25 30.1 33
150 x 50 60.4 17
180 x 5 7.25 138
180 x 6 8.69 115
180 x 10 14.5 69
180 x 12 17.4 57
180 x 16 23.2 43
180 x 20 29.0 34
Steel Centre
180 x 25 36.2 28
19
KNOW YOUR STEEL

Size Mass Metres

200 x 6 9.66 104

200 x 8 12.9 78
200 x 10 16.1 62
200 x 12 19.3 52
200 x 16 25.7 39
200 x 20 32.2 31
200 x 25 40.3 25
250 x 6 12.1 83
250 x 8 16.1 62
250 x 10 20.1 50
250 x 12 24.2 41 Note: Mass Calculations include
250 x 16 32.2 31 a 2.5 per cent rolling tolerance
for this product.
250 x 20 40.3 25
250 x 25 50.3 20
300 x 6 14.5 69
300 x 8 19.3 52
300 x 10 24.2 41
300 x 12 29.0 34
300 x 16 38.6 26
300 x 20 48.3 21
300 x 25 60.4 17
|
Bar Sections

• Non-Residential Construction strength to weight ratios
• Mining Infrastructure • Requires no special pre-heating
for welding
• Manufacturing
Steel Centre
20
KNOW YOUR STEEL
Round Bars
Size Mass Metres

10 0.64 1563
12 0.91 1099
14 1.24 806
16 1.62 617
18 2.05 488
20 2.53 395
22 3.05 328
24 3.64 275
27 4.61 217
30 5.69 176
33 6.88 145 Note: Mass Calculations include
36 8.19 122 a 2.5 per cent rolling tolerance
for this product.
39 9.61 104
42 11.2 89
Bar Sections
45 12.8 78
48 14.6 68
50 15.8 63
56 19.8 51
60 22.8 44
|
65 26.7 37
Round Bars
75 35.6 28
80 40.5 25
90 51.1 20
100 63.2 16
110 76.7 13
120 91.2 11
130 108 9
140 124 8
150 142 7
160 162 6
170 183 5
180 206 5
190 229 4
200 253 4

• Non-Residential Construction strength to weight ratios
• Mining Infrastructure • Requires no special pre-heating
for welding
• Manufacturing
Steel Centre
21
KNOW YOUR STEEL
Square Bars
Size Mass Metres

10 x 10 0.81 1235
12 x 12 1.16 862
16 x 16 2.06 485
20 x 20 3.22 311
25 x 25 5.03 199
32 x 32 8.24 121
40 x 40 12.9 78

• Engineering Construction • Meets AS/NZS 3679.1:2016 Note: Mass Calculations include a
2.5 per cent rolling tolerance for this
• Residential & Non- • Up to 20% stronger for improved product.
Residential Construction strength to weight ratios
Square Bars and Channels
• Transport and Storage for welding
• Manufacturing
Parallel Flange Channels

|

Bar Sections
Size Mass Metres

75 x 40 5.92 169
100 x 50 8.33 120
125 x 65 11.9 84

• Residential & Non- • Up to 20% stronger for improved
Residential Construction strength to weight ratios
• Transport and Storage for welding
• Manufacturing Structural Steel Channels.
Steel Centre
22
KNOW YOUR STEEL
Billets
Size Mass Metres

45 x 45 16.3 61
50 x 50 19.4 52
63 x 63 31.2 32
75 x 75 45.3 22
®
DuraGal Channels
Bar Sections
Length/Pack
Nominal
Length Mass Metres
Dim 1 Dim 2 Thickness Standard (m)
m kg/m per tonne
mm
9.0 12.0
|
75 x 40 x 4 9.0 4.43 226 18
Billets
100 x 50 x 4 9.0 5.58 179 18
125 x 65 x 4 9.0 7.60 132 18
150 x 75 x 5 12.0 11.2 89 12
180 x 75 x 5 12.0 12.4 81 12
200 x 75 x 5 12.0 13.2 76 12
200 x 75 x 6 12.0 15.7 64 12
230 x 75 x 6 12.0 17.2 58 12
250 x 90 x 6 12.0 19.6 51 8
300 x 90 x 6 12.0 22.0 45 6
Note: Some sizes may be subject to
rolling MOQs.
• Residential Construction • High strength roll-formed sections made from pre-
• Non-Residential coated strip of zinc, aluminium and magnesium
Construction • Minimum coating of 250g/m2 and self-healing
• Fabrication properties
• Smooth quality finish
• Significantly lighter than traditional hot rolled sections
• Smooth surface allows easy powdercoating and
painting
Steel Centre
23
KNOW YOUR STEEL
®
DuraGal Angles
Unequal Angles
Nominal
Length Mass Metres
Dim 1 Dim 2 Thickness m kg/m per tonne
mm
75 x 50 x 4 9.0 3.73 268
75 x 50 x 5 9.0 4.58 218
75 x 50 x 6 9.0 5.46 183
90 x 75 x 6 9.0 7.44 134
100 x 75 x 6 12.0 7.87 127
125 x 75 x 5 12.0 7.54 133
125 x 75 x 6 12.0 9.08 110
150 x 100 x 6 12.0 11.5 87

Note: Some sizes may be subject to
• Residential Construction • High strength roll-formed sections made from pre-
rolling MOQs.
• Non-Residential coated strip of zinc, aluminium and magnesium
DuraGal® Angles
Construction • Minimum coating of 250g/m2 and self-healing

• Fabrication properties
• Smooth quality finish
• Smooth surface allows easy powdercoating and
painting
|
Bar Sections
Merchant Bar Processing

We can process Flats, Rounds and Angles using Beamlines, Band Saws, Croppers and
Oxy Bevelling Machines.
Applications include: Straight cuts, pack cuts, mitre cutting, drilling, notching, punching,
shearing and cropping.
Steel Centre
24
KNOW YOUR STEEL
®
DuraGal Angles
Equal Angles
Length/Pack
Nominal
Length Mass Metres
Dim 1 Dim 2 Thickness Standard
m kg/m per tonne
mm
6.0 9.0 12.0
25 x 25 x 2.5 6.0 0.89 1119 80
30 x 30 x 2.5 6.0 1.09 915 80
40 x 40 x 2.5 6.0 1.49 671 60
40 x 40 x 4.0 6.0 2.31 433 39
45 x 45 x 2.5 6.0 1.69 592
50 x 50 x 2.5 6.0 1.89 530 33 33
50 x 50 x 4.0 6.0 2.94 340 27 27
50 x 50 x 5.0 12.0 3.59 278 24 24 24
50 x 50 x 6.0 9.0 4.25 235 21
65 x 65 x 4.0 9.0 3.89 257 22 Note: Some sizes may be subject to
65 x 65 x 5.0 9.0 4.78 209 22 rolling MOQs.
65 x 65 x 6.0 9.0 5.70 176 18

75 x 75 x 4.0 9.0 4.53 221 22
Bar Sections
75 x 75 x 5.0 6.0 5.57 180 22 22
75 x 75 x 6.0 9.0 6.66 150 18
90 x 90 x 5.0 9.0 6.75 148 22
90 x 90 x 6.0 9.0 8.11 123
100 x 100 x 6.0 12.0 9.08 110
|
150 x 150 x 6.0 12.0 13.9 72
DuraGal® Angles
• Residential Construction • High Strength roll-formed sections made from pre-coated
• Non-Residential strip of zinc, aluminium and magnesium
Construction • Minimum coating of 250g/m2 and self-healing properties
• Fabrication • Smooth quality finish
• Smooth surface allows easy powdercoating and painting
Steel Centre
25
KNOW YOUR STEEL
DuraGal® Flat Bars
Length/Pack
Length Mass Metres
Dim 1 Dim 2 Standard (m)
m kg/m per tonne
6.0
50 x 4 6.0 1.582 632 57
50 x 5 6.0 1.975 506 45
65 x 5 6.0 2.567 390 36
75 x 4 6.0 2.373 421 38
75 x 5 6.0 2.962 338 32
90 x 6 6.0 4.346 230 26
100 x 4 6.0 3.165 316 28
100 x 5 6.0 3.950 253 28
100 x 6 6.0 4.829 207 26
130 x 5 6.0 5.134 195 28 Note: some sizes may be subject
150 x 5 6.0 5.924 169 28 to rolling MOQs.
150 x 6 6.0 7.243 138 24

DuraGal® Flat Bars
200 x 5 6.0 7.899 127 32

250 x 5 6.0 9.874 101 23
300 x 5 6.0 11.849 84 19
Information reflects standard lengths as well as lengths available ex-rolling.

Subject to MOQ.
|

Bar Sections
• Residential Construction • High strength roll-formed sections made from pre-coated

• Non-Residential strip of zinc, aluminium and magnesium
Construction • Minimum coating of 250g/m2 and self-healing properties
• Fabrication • Smooth quality finish
• Smooth surface allows easy powdercoating and painting
Tubular Processing
InfraBuild Steel Centre can process Pipe and Tube using a variety of
machinery including Band Saws, Power Hacksaws, Tube saws and Beamlines.
Applications include: Straight cuts, pack cuts, drilling and de-burring.
Steel Centre
26
Tubular
KNOW YOUR STEEL

Square Hollow Sections (SHS)
Length/Pack
Size Surface Mass Metres Standard (m)
mm × mm × mm Finish kg/m per tonne
6.5 8.0
25 x 25 x 1.6 P,S 1.12 890 100
25 x 25 x 2.0 P,S 1.36 733 100
25 x 25 x 2.5 P,S 1.64 610 100
25 x 25 x 3.0 P,S 1.89 529 100
30 x 30 x 1.6 P,S 1.38 727 100
30 x 30 x 2.0 P,S 1.68 596 100
30 x 30 x 2.5 P,S 2.03 492 100
30 x 30 x 3.0 P,S 2.36 423 64
35 x 35 x 1.6 P,S 1.63 615 100
Surface Finishes:
35 x 35 x 2.0 P,S 1.99 502 100 C – DuraGal®Clear
35 x 35 x 2.5 P,S 2.42 412 64 S – DuraGal®
35 x 35 x 3.0 P,S 2.83 353 64 Z – DuraGal®ZB135/135
40 x 40 x 1.6 P,S 1.88 533 81 P – DuraPrimed®
Tubular
40 x 40 x 2.0 P,S 2.31 434 81
O – Oiled
40 x 40 x 2.5 P,S 2.82 355 64
40 x 40 x 3.0 P,S 3.30 303 64 Typical Uses:
|
40 x 40 x 4.0 P,S 4.09 244 49 • Engineering Construction
Square Hollow Sections

50 x 50 x 1.6 P,S 2.38 420 64
50 x 50 x 2.0 P,S 2.93 300 64
• Non-Residential
50 x 50 x 2.5 P,S 3.60 278 49
Construction
50 x 50 x 3.0 P,S 4.25 236 49
50 x 50 x 4.0 P,S 5.35 187 36
50 x 50 x 5.0 P,S 6.39 156 30
50 x 50 x 6.0 O 7.32 137 25
• Manufacturing
65 x 65 x 1.6 P,S 3.13 319 49 • Agriculture
65 x 65 x 2.0 P,S,C 3.88 258 42
65 x 65 x 2.5 P,S,C 4.78 209 42 Features:
65 x 65 x 3.0 P,S 5.66 177 36
• Available in Grades C350L0
65 x 65 x 4.0 P,S,C 7.23 138 30
and C450PLUS™.
65 x 65 x 5.0 P,S 8.75 114 25
65 x 65 x 6.0 P 10.1 98.6 20 • All tube manufactured to
75 x 75 x 2.0 P,S,C 4.50 222 36
meet AS/NZS 1163:2016
75 x 75 x 2.5 P,S,C 5.56 180 30 • Available in various coating
75 x 75 x 3.0 P,S 6.60 152 30 types including DuraGal®,
75 x 75 x 3.5 P,S 7.53 133 25 DuraGal®ZB135/135,
DuraPrimed® and NOPC
75 x 75 x 4.0 P,S,C 8.49 118 25
(No Oil or Paint Coating).
75 x 75 x 5.0 P,S 10.3 96.9 20
• DuraGal® hot-dip
75 x 75 x 6.0 P 12.0 83.1 16
galvanized coating has
89 x 89 x 2.0 S 5.38 186 20
a minimum average zinc
89 x 89 x 3.5 P,S,C 9.07 110 20 mass of 100g/m2.
89 x 89 x 5.0 P,S 12.5 80.0 16
89 x 89 x 6.0 P 14.7 68.3 12
90 x 90 x 2.0 Z 5.45 184 20 Note: See page 27-28 for Rectangular
Hollow Sections.
Steel Centre
27
KNOW YOUR STEEL
Square Hollow Sections (SHS)
Length/Pack
Size Surface Mass Metres
mm × mm × mm Finish kg/m per tonne Standard (m)
8.0 12
100 x 100 x 2.0 P 6.07 165 20 20
100 x 100 x 2.5 P,S 7.53 133 20
100 x 100 x 3.0 P,S,C 8.96 112 20 16
100 x 100 x 4.0 P,S 11.6 86.0 16 12
100 x 100 x 5.0 P,S,C 14.2 70.2 12 9
100 x 100 x 6.0 P 16.7 59.7 12 9
100 x 100 x 8.0 O 21.4 46.7 9 6
100 x 100 x 9.0 O 23.5 42.5 9 6 Surface Finishes:
100 x 100 x 10.0 O 25.6 39.0 6
C – DuraGal®Clear
125 x 125 x 4.0 P 14.8 67.7 12 9 S – DuraGal®
125 x 125 x 5.0 P 18.2 55.0 12 9 Z – DuraGal®ZB135/135
125 x 125 x 6.0 P 21.4 46.6 9 6 P – DuraPrimed®
125 x 125 x 8.0 O 27.7 36.1 6 4 O – Oiled

125 x 125 x 9.0 P,O 30.6 32.7 8 4
125 x 125 x 10.0 O 33.4 29.9 4 Typical Uses:
150 x 150 x 5.0 P 22.1 45.3 9 6
150 x 150 x 6.0 P 26.2 38.2 6 6
150 x 150 x 8.0 O 33.9 29.5 6 4
150 x 150 x 9.0 P,O 37.7 26.6 6 4 • Non-Residential
Construction
150 x 150 x 10.0 O 41.3 24.2 2
200 x 200 x 5.0 O 29.9 33.4 6 4
|
200 x 200 x 6.0 O 35.6 28.1 4 4

Tubular
200 x 200 x 8.0 O 46.5 21.5 4 2 • Manufacturing

200 x 200 x 9.0 O 51.8 19.3 4 2 • Agriculture
200 x 200 x 10.0 O 57.0 17.6 2
200 x 200 x 12.5 O 69.4 14.4 2 Features:
200 x 200 x 16.0 O 85.5 11.7 1
250 x 250 x 6.0 O 45.0 22.2 4 2 • Available in Grades C350L0
250 x 250 x 8.0 O 59.1 16.9 4 2 and C450PLUS™
250 x 250 x 9.0 O 65.9 15.2 2 2 • All tube manufactured to
250 x 250 x10.0 O 72.7 13.8 2 meet AS/NZS 1163:2016
250 x 250 x 12.5 O 89.0 11.2 1 • Available in various coating
250 x 250 x 16.0 O 111 9.04 1 types including DuraGal®,
300 x 300 x 8.0 O 71.6 14.0 1 DuraGal®ZB135/135,
300 x 300 x 10.0 O 88.4 11.3 1 DuraPrimed® and NOPC
300 x 300 x 12.5 O 109 9.21 1 (No Oil or Paint Coating).
300 x 300 x 16.0 O 136 7.36 1 • DuraGal® hot-dip galvanized
350 x 300 x 8.0 O 84.2 11.9 1
coating has a minimum
average zinc mass of 100g/
350 x 300 x 10.0 O 104 9.61 1
m2.
350 x 300 x 12.5 O 128 7.80 1
350 x 300 x 16.0 O 161 6.21 1
400 x 400 x 10.0 O 120 8.35 1
400 x 400 x 12.5 O 148 6.76 1 Note: See page 27-28 for Rectangular
Hollow Sections.
400 x 400 x 16.0 O 186 5.38 1
Steel Centre
28
KNOW YOUR STEEL
Rectangular Hollow Sections (RHS)
Length/Pack
8.0 12
50 x 25 x 1.6 P,S 1.75 571 96
50 x 25 x 2.0 P,S 2.15 465 96
50 x 25 x 2.5 P,S 2.62 382 72
50 x 25 x 3.0 P,S 3.07 326 60
65 x 35 x 2.0 P,S 2.93 341 54
65 x 35 x 2.5 P,S 3.60 278 54
65 x 35 x 3.0 P,S 4.25 236 45
65 x 35 x 4.0 P, S 5.35 187 45 Surface Finishes:
75 x 25 x 1.6 P,S 2.38 420 65
C – DuraGal®Clear
75 x 25 x 2.0 P,S 2.93 341 65 S – DuraGal®
75 x 25 x 2.5 P,S 3.60 278 48 Z – DuraGal®ZB135/135
75 x 50 x 1.6 P,S,C 3.01 332 54 54 P – DuraPrimed®
Tubular
75 x 50 x 2.0 P,S 3.72 269 42 42 O – Oiled
75 x 50 x 2.5 P,S 4.58 218 42 24
75 x 50 x 3.0 P,S 5.42 184 35 24 Typical Uses:
|
75 x 50 x 4.0 P,S 6.92 145 28 24
Rectangular Hollow Sections

75 x 50 x 5.0 P,S 8.35 120 24 20
75 x 50 x 6.0 P 9.67 103 20 16
100 x 50 x 1.6 P,S,C,Z 3.64 275 32 32 • Non-Residential
Construction
100 x 50 x 2.0 P,S,C,Z 4.50 222 32 32
100 x 50 x 2.5 P,S 5.56 180 32 24
100 x 50 x 3.0 P,S 6.60 152 32 24 • Transport and Storage
100 x 50 x 3.5 P,S 7.53 133 24 18 • Manufacturing
100 x 50 x4.0 P,S 8.49 118 24 18 • Agriculture
100 x 50 x 5.0 P,S 10.3 96.9 18 15
100 x 50 x 6.0 P 12.0 83.1 15 12 Features:
102 x 76 x 3.5 P, S 9.07 110 12
102 x 76 x 5.0 P, S 12.5 79.9 12 • Available in Grades C350L0
102 x 76 x 6.0 P, S 14.7 68.2 12 and C450PLUS™
125 x 75 x 2.0 P 6.07 165 24 • All tube manufactured to
125 x 75 x 2.5 P,S 7.53 133 20 20 meet AS/NZS 1163:2016
125 x 75 x 3.0 P,S 8.96 112 20 15 • Available in various coating
125 x 75 x 4.0 P,S 11.6 86.0 15 15 types including DuraGal®,
125 x 75 x 5.0 P,S 14.2 70.2 15 12 DuraGal®ZB135/135,
125 x 75 x 6.0 P 16.7 59.7 12 6 DuraPrimed® and NOPC
127 x 51 x 3.5 P 9.07 110 12 (No Oil or Paint Coating).
127 x 51 x 5.0 P 12.5 79.9 8 • DuraGal® hot-dip galvanized
127 x 51 x 6.0 P 14.7 68.2 8
average zinc mass of 100g/
m2.
Note: See page 25-26 for Square

Hollow Sections
Steel Centre
29
KNOW YOUR STEEL
Rectangular Hollow Sections (RHS)
Length/Pack
8.0 12
150 x 50 x 2.0 P,S,C,Z 6.07 165 21 21
150 x 50 x 2.5 P,S 7.53 133 24 18
150 x 50 x 3.0 P,S,C 8.96 112 21 15
150 x 50 x 4.0 P,S 11.6 86.0 15 15
150 x 50 x 5.0 P,S 14.2 70.2 15 9
150 x 50 x 6.0 P 16.7 59.7 15 9
150 x 100 x 4.0 P 14.8 67.7 12 9
150 x 100 x 5.0 P 18.2 55.0 12 8
150 x 100 x 6.0 P 21.4 46.6 9 6
Surface Finishes:
150 x 100 x 8.0 O 27.7 36.1 4 C – DuraGal®Clear
150 x 100 x 9.0 O 30.6 32.7 6 4 S – DuraGal®
152 x 76 x 5.0 O 16.4 60.7 8 8 Z – DuraGal®ZB135/135
152 x 76 x 6.0 O 19.4 51.5 8 8 P – DuraPrimed®

O – Oiled
200 x 100 x 4.0 P 17.9 55.8 8 6
200 x 100 x 5.0 P 22.1 45.3 8 6
200 x 100 x 6.0 P 26.2 38.2 8 4
Typical Uses:
200 x 100 x 8.0 O 33.9 29.5 6 4 • Engineering Construction
200 x 100 x 9.0 O 37.7 26.6 6 4
250 x 150 x 5.0 O 29.9 33.4 6 4
• Non-Residential
250 x 150 x 6.0 O 35.6 28.1 4 4 Construction
250 x 150 x 8.0 O 46.5 21.5 4 2
250 x 150 x 9.0 O 51.8 19.3 4 2
250 x 150 x 10.0 O 57.0 17.6 2
• Manufacturing
|
250 x 150 x 12.5 O 69.4 14.4 1

Tubular
250 x 150 x16.0 O 85.5 11.7 1 • Agriculture

300 x 200 x 6.0 O 45.0 22.2 2 1
300 x 200 x 8.0 O 59.1 16.9 2 1 Features:
300 x 200 x 9.0 O 65.9 15.2 2
• Available in Grades C350L0
300 x 200 x 10.0 O 72.7 13.8 1 1
and C450PLUS™
300 x 200 x 12.5 O 89.0 11.2 1
300 x 200 x 16.0 O 111 9.04 1 • All tube manufactured to
350 x 250 x 8.0 O 71.6 14.0 2
350 x 250 x 10.0 O 88.4 11.3 1 • Available in various coating
350 x 250 x 12.5 O 109 9.21 1 types including DuraGal®,
350 x 250 x 16.0 O 136 7.36 1
DuraGal® ZB135/135,
DuraPrimed® and NOPC
400 x 200 x 8.0 O 71.6 14.0 2
(No Oil or Paint Coating).
400 x 200 x 10.0 O 88.4 11.3 1
• DuraGal® hot-dip galvanized
400 x 200 x 12.5 O 109 9.21 1
400 x 200 x 16.0 O 136 7.36 1 average zinc mass of 100g/
400 x 300 x 8.0 O 84.2 11.9 1 m2.
400 x 300 x 10.0 O 104 9.61 1
400 x 300 x 12.5 O 128 7.80 1
400 x 300 x 16.0 O 161 6.21 1 Note: See page 25-26 for Square
Hollow Sections.
Information reflects standard lengths as well as lengths available ex-rolling. Subject to MOQ.
Steel Centre
30
Higher strength and more efficient
structural steel - C450PLUS™
C450PLUS™ is a unique dual-grade tubular section offering the strength of
450-grade steel with the elongation, formability and weldability of 350-grade.
Available in all sizes of SHS and RHS, with coating options including
DuraGal®, DuraPrimed® and oiled.
KNOW YOUR STEEL
Stock Rail and Posts
Stock Rail Sections

Designation Wall Thickness Mass Metres Pack Size
d x b mm mm kg/m per tonne (Lns)
53 x 35 1.6 1.77 565 48
60 x 48 2.0 2.88 347 36
66 x 44 1.6 2.23 448 36
75 x 40 1.6 2.39 418 20
75 x 40 2.0 2.97 337 20
97 x 40 2.0 3.65 274 21
115 x 42 2.0 4.27 234 21
115 x 42 2.5 5.30 189 21
120 x 48 2.0 4.53 221 18
Note: Some sizes subject to rolling MOQs.

Features:
• Coated in DuraGal® for
superior corrosion protection
Stock Rail and Silo Sections
Post Sections
Designation Wall Thickness Mass Metres Pack Size • All tube manufactured to
d x b mm mm kg/m per tonne (Lns) meet AS/NZS 1163:2016
40 x 40 1.6 1.88 532 81 • Smooth elongated edges
40 x 40 2.0 2.31 433 81 minimise risk of bruising and
50 x 50 1.6 2.38 420 64 injury to livestock
50 x 50 2.0 2.93 341 64 • Lightweight, easy to handle
75 x 75 4.0 8.49 118 25 and transport
100 x 100 4.0 11.6 86 16
• Flat sides allow for easy
connectivity
• Minimal weld spatter
|
or fumes
Tubular
Silo Sections
DuraPrimed®, DuraGal®
Designation Wall Thickness Mass Metres Pack Size
d x b mm mm kg/m per tonne (Lns)
75 x 64 2.5 4.75 211 36
75 x 64 3.0 5.56 180 24
Note: DuraPrimed® replaces Painted.
Features:
• Available in DuraPrimed®
and DuraGal®
• All tube manufactured to
Steel Centre
32
KNOW YOUR STEEL
Stock Rail Accessories
Product Image Product Name Product Code Weight (kg/EA) Box Quantity
Cattle Rail Joiner VRH115 0.50 30
Cattle Rail Zinc Cap VRH115C 0.10 50
Cattle Rail Clip VRH115CLIP 0.10 60
Tubular
Cattle Rail End Joiner VRH115EJ 0.50 30
|
Stock Rail Accessories
Cattle Rail Hanger Double
VCATTLECR 0.75 24
End
Cattle Rail Hanger Single VCATTLECRH 0.35 48
Cattle Rail Plastic End Cap VACEPC01154 0.09 125
Tubular Processing
InfraBuild Steel Centre can process Pipe and Tube using a variety of
machinery including Band Saws, Power Hacksaws, Tube saws and Beamlines.
Applications include: Straight cuts, pack cuts, drilling and de-burring.
Steel Centre
33
KNOW YOUR STEEL
Circular Hollow Sections (CHS)

Stock Range Overview
Nominal Outside Wall Mass Nominal Outside Wall Mass

Length Length
Size Section Diameter Thickness Size Section Diameter Thickness
m m
(NB) mm mm kg/m m/t (NB) mm mm kg/m m/t
8 Black M 13.5 2.3 5.8 0.641 1560 65 Black XL 76.1 2.3 6.5 4.19 239
8 Black H 13.5 2.9 5.8 0.765 1310 65 Black L 76.1 3.2 6.5 5.75 174
8 Gal. M 13.5 2.3 5.8 0.670 1490 65 Black M 76.1 3.6 6.5 6.43 156
8 Gal. H 13.5 2.9 5.8 0.792 1260 65 Black H 76.1 4.5 6.5 7.93 126
10 Black M 17.2 2.3 6.5 0.839 1190 65 Black XH 76.1 5.9 6.5 10.2 98
10 Black H 17.2 2.9 6.5 1.02 985 65 Gal. XL 76.1 2.3 6.5 4.37 229
10 Gal. M 17.2 2.3 6.5 0.877 1140 65 Gal. L 76.1 3.2 6.5 5.94 168
10 Gal. H 17.2 2.9 6.5 1.05 951 65 Gal. M 76.1 3.6 6.5 6.61 151
15 Black L 21.3 2.0 6.5 0.952 1050 65 Gal. H 76.1 4.5 6.5 8.12 123
15 Black M 21.3 2.6 6.5 1.21 830 80 Black XL 88.9 2.6 6.5 5.53 181
15 Black H 21.3 3.2 6.5 1.44 696 80 Black L 88.9 3.2 6.5 6.76 148
15 Black XH 21.3 3.6 6.5 1.57 636 80 Black M 88.9 4.0 6.5 8.37 120
15 Gal. L 21.3 2.0 6.5 1.00 999 80 Black H 88.9 5.0 6.5 10.3 97
15 Gal. M 21.3 2.6 6.5 1.25 798 80 Black XH 88.9 5.9 6.5 12.1 83
15 Gal. H 21.3 3.2 6.5 1.48 674 80 Gal. XL 88.9 2.6 6.5 5.75 174
20 Black XL 26.9 2.0 6.5 1.23 814 80 Gal. L 88.9 3.2 6.5 6.98 143
Circular Hollow Sections
20 Black L 26.9 2.3 6.5 1.40 717 80 Gal. M 88.9 4.0 6.5 8.58 117
20 Black M 26.9 2.6 6.5 1.56 642 80 Gal. H 88.9 5.0 6.5 10.5 95
20 Black H 26.9 3.2 6.5 1.87 535 90 Black XL 101.6 2.6 6.5 6.35 158
20 Black XH 26.9 4.0 6.5 2.26 443 90 Black L 101.6 3.2 6.5 7.77 129
20 Gal. XL 26.9 2.0 6.5 1.29 774 90 Black M 101.6 4.0 6.5 9.63 104
20 Gal. L 26.9 2.3 6.5 1.46 686 90 Black H 101.6 5.0 6.5 11.9 84
20 Gal. M 26.9 2.6 6.5 1.62 617 90 Gal. XL 101.6 2.6 6.5 660 152
20 Gal. H 26.9 3.2 6.5 1.93 518 90 Gal. L 101.6 3.2 6.5 8.02 125
25 Black XL 33.7 2.0 6.5 1.56 640 90 Gal. M 101.6 4.0 6.5 9.88 101
25 Black L 33.7 2.6 6.5 1.99 501 90 Gal. H 101.6 5.0 6.5 12.20 82
25 Black M 33.7 3.2 6.5 2.41 414 100 Black XL 114.3 3.2 6.5 8.77 114
25 Black H 33.7 4.0 6.5 2.94 340 100 Black L 114.3 3.6 6.5 9.83 102
|
25 Black XH 33.7 4.5 6.5 3.24 309 100 Black M 114.3 4.5 6.5 12.2 82
Tubular
25 Gal. XL 33.7 2.0 6.5 1.64 608 100 Black H 114.3 5.4 6.5 14.5 69
25 Gal. L 33.7 2.6 6.5 2.07 482 100 Gal. XL 114.3 3.2 6.5 9.05 110
25 Gal. M 33.7 3.2 6.5 2.49 401 100 Gal. L 114.3 3.6 6.5 10.1 99
25 Gal. H 33.7 4.0 6.5 3.02 332 100 Gal. M 114.3 4.5 6.5 12.4 80
32 Black XL 42.4 2.0 6.5 1.99 502 100 Gal. H 114.3 5.4 6.5 14.8 87
32 Black L 42.4 2.6 6.5 2.55 392 125 Black XL 139.7 3.0 6.5 10.1 99
32 Black M 42.4 3.2 6.5 3.10 322 125 Black L 139.7 3.5 6.5 11.8 85
32 Black H 42.4 4.0 6.5 3.80 263 125 Black M 139.7 5.0 6.5 16.6 60
32 Black XH 42.4 4.9 6.5 4.53 221 125 Black H 139.7 5.4 6.5 17.9 56
32 Gal. XL 42.4 2.0 6.5 2.10 477 125 Gal. XL 139.7 3.0 6.5 10.5 96
32 Gal. L 42.4 2.6 6.5 2.65 377 125 Gal. L 139.7 3.5 6.5 12.1 83
32 Gal. M 42.4 3.2 6.5 3.20 312 125 Gal. M 139.7 5.0 6.5 16.9 59
32 Gal. H 42.4 4.0 6.5 3.92 257 125 Gal. H 139.7 5.4 6.5 18.2 55
40 Black XL 48.3 2.3 6.5 2.61 383 150 Black XL 165.1 3.0 6.5 12.0 84
40 Black L 48.3 2.9 6.5 3.25 308 150 Black L 165.1 3.5 6.5 13.9 72
40 Black M 48.3 3.2 6.5 3.56 281 150 Black M 165.1 5.0 6.5 19.7 51
40 Black H 48.3 4.0 6.5 4.37 229 150 Black H 165.1 5.4 6.5 21.3 47
40 Black XH 48.3 5.4 6.5 5.71 175 150 Gal. XL 165.1 3.0 6.5 12.4 61
40 Gal. XL 48.3 2.3 6.5 2.73 367 150 Gal. L 165.1 3.5 6.5 14.4 70
40 Gal. L 48.3 2.9 6.5 3.36 297 150 Gal. M 165.1 5.0 6.5 20.1 50
40 Gal. M 48.3 3.2 6.5 3.68 272 150 Gal. H 165.1 5.4 6.5 21.7 46
40 Gal. H 48.3 4.0 6.5 4.49 223
50 Black XL 60.3 2.3 6.5 3.29 304
50 Black L 60.3 2.9 6.5 4.11 244
50 Black M 60.3 3.6 6.5 5.03 199
50 Black H 60.3 4.5 6.5 6.19 161
Steel Centre
50 Black XH 60.3 5.4 6.5 7.31 137

50 Gal. XL 60.3 2.3 6.5 3.44 291
50 Gal. L 60.3 2.9 6.5 4.25 235
50 Gal. M 60.3 3.6 6.5 5.18 193
50 Gal. H 60.3 4.5 6.5 6.33 158
Note: Some sizes subject to rolling MOQs.
34
KNOW YOUR STEEL
Black
Nominal Outside Wall

Mass Metres Pack Size
Size Section Diameter Thickness kg/m per tonne (Lns)
(DN) mm mm
25 Extra Light 33.7 2.0 1.56 641 91
25 Light 2.6 1.99 503 91
25 Medium 3.2 2.41 415 91
25 Heavy 4.0 2.94 340 91
32 Extra Light 42.4 2.0 1.99 503 61
32 Light 2.6 2.55 392 61
32 Medium 3.2 3.10 323 61
32 Heavy 4.0 3.80 263 61
40 Extra Light 48.3 2.3 2.61 383 61
40 Light 2.9 3.25 308 61
40 Medium 3.2 3.57 280 61
40 Heavy 4.0 4.38 228 61
40 Extra Heavy 5.4 5.71 175 61
50 Extra Light 60.3 2.3 3.29 304 37
Typical Uses:
Tubular
50 Light 2.9 4.11 243 37 • Engineering Construction
50 Medium 3.6 5.03 199 37 • Residential Construction
50 Heavy 4.5 6.19 162 37 • Non-Residential
|
50 Extra Heavy 5.4 7.31 137 37 Construction

65 Extra Light 76.1 2.3 4.19 239 37 • Mining Infrastructure
65 Light 3.2 5.75 174 37
65 Medium 3.6 6.43 156 37
• Manufacturing
65 Heavy 4.5 7.93 126 37
• Agriculture
65 Extra Heavy 5.9 10.2 97 37
80 Extra Light 88.9 2.6 5.53 181 19
80 Light 3.2 6.76 148 19 Features:
80 Medium 4.0 8.37 119 19
• Extra Light and
80 Heavy 5.0 10.3 97 19 Light sections meet
80 Extra Heavy 5.9 12.1 83 19 AS/NZS 1163: 2016 C350L0
90 Extra Light 101.6 2.6 6.35 157 19 • Medium and Heavy sections
90 Light 3.2 7.77 129 19 meet AS 1074 & AS/NZS
90 Medium 4.0 9.63 104 19 1163 - C250
90 Heavy 5.0 11.9 84 19
100 Extra Light 114.3 3.2 8.77 114 19
100 Light 3.6 9.83 102 19
100 Medium 4.5 12.2 82 19
100 Heavy 5.4 14.5 69 19
125 Extra Light 139.7 3.0 10.1 99 13
125 Light 3.5 11.8 85 13
125 Medium 5.0 16.6 60 13
125 Heavy 5.4 17.9 56 13
150 Extra Light 165.1 3.0 12.0 83 10
150 Light 3.5 13.9 72 10
150 Medium 5.0 19.7 51 10
150 Heavy 5.4 21.3 47 10
Steel Centre
35
KNOW YOUR STEEL

DuraGal®

(DN) mm mm
25 Extra Light 33.7 2.0 1.56 641 91
25 Light 2.6 1.99 503 91
25 Medium 3.2 2.41 415 91
32 Extra Light 42.4 2.0 1.99 503 61
32 Light 2.6 2.55 392 61
32 Medium 3.2 3.10 323 61
40 Extra Light 48.3 2.3 2.61 383 61
40 Light 2.9 3.25 308 61
40 Medium 3.2 3.57 280 61
50 Extra Light 60.3 2.3 3.29 304 37
50 Light 2.9 4.11 243 37
50 Medium 3.6 5.03 199 37
65 Extra Light 76.1 2.3 4.19 239 37
65 Light 3.2 5.75 174 37
Typical Uses:
65 Medium 3.6 6.43 156 37 • Engineering Construction

80 Extra Light 88.9 2.6 5.53 181 19 • Residential Construction
80 Light 3.2 6.76 148 19 • Non-Residential
80 Medium 4.0 8.37 119 19 Construction
90 Light 101.6 3.2 7.77 129 19 • Mining Infrastructure
90 Medium 4.0 9.63 104 19
100 Light 114.3 3.6 9.83 102 19
• Manufacturing
100 Medium 4.5 12.20 82 19
• Agriculture
Available off mill rolling only. Minimum order quantity required.
|
Tubular
Features:
• Medium Dual Specified
AS 1074 / AS/NZS 1163
C250L0
Circular Hollow Sections (CHS) • Extra Light and Light
AS/NZS 1163: 2016 C350L0
DuraPrimed Red™ • DuraGal coating
AS/NZS 4792: 2006
ZB100/100
(DN) mm mm
25 Medium 33.7 3.2 2.41 414 91
32 Medium 42.4 3.2 3.10 322 61
40 Medium 48.3 3.2 3.57 280 61
50 Medium 60.3 3.6 5.03 199 37
65 Medium 76.1 3.6 6.43 156 37
80 Medium 88.9 4.0 8.37 120 19
100 Medium 114.3 4.5 12.2 82.2 19

Steel Centre
• Fire System Tube • Dual Specified AS 1074 and AS/NZS 1163 C250LO
• Available in plain ends, screwed one end and
screwed both ends
36
KNOW YOUR STEEL
Hot-dip Galvanised

(DN) mm mm
32 Heavy 42.4 4.0 3.87 258 61
40 Heavy 48.3 4.0 4.46 224 61
50 Medium 60.3 3.6 5.14 195 37
50 Heavy 60.3 4.5 6.30 159 37
65 Medium 76.1 3.6 6.56 152 37
65 Heavy 76.1 4.5 8.07 124 37
80 Extra Light 88.9 2.6 5.75 174 19
80 Light 88.9 3.2 6.92 145 19
80 Medium 88.9 4.0 8.53 117 19
80 Heavy 88.9 5.0 10.50 95 19
90 Extra Light 101.6 2.6 6.64 151 19
90 Light 101.6 3.2 8.02 125 19
90 Medium 101.6 4.0 9.81 102 19
Tubular
90 Heavy 101.6 5.0 12.10 83 19
100 Extra Light 114.3 3.2 9.05 110 19
100 Light 114.3 3.6 10.00 100 19
100 Medium 114.3 4.5 12.40 81 19
|
100 Heavy 114.3 5.4 14.70 68 19

125 Extra Light 139.7 3.0 10.50 95 10
125 Light 139.7 3.5 12.10 83 10
125 Medium 139.7 5.0 16.90 59 10
125 Heavy 139.7 5.4 18.10 55 10
150 Extra Light 165.1 3.0 12.40 81 10
150 Light 3.5 14.40 69 10
150 Medium 5.0 20.00 50 10
150 Heavy 5.4 21.60 46 10

• Engineering Construction • Medium and Heavy Dual
• Residential Construction Specified AS 1074 and AS/NZS
1163 C250L0
• Non-Residential Construction
• Extra Light and Light AS/NZS
1163 C350L0
• Hot Dip Galvanized
• Manufacturing AS/NZS 4680: 2006 HDG 300
• Agriculture
Steel Centre
37
KNOW YOUR STEEL
Structural CHS
Size Mass Size Mass Size Mass

d x t mm kg/m d x t mm kg/m d x t mm kg/m
60.3 x 4.0 5.42 141.3 x 7.1 273.1 x 15.1
60.3 x 4.8 6.50 141.3 x 8.2 323.9 x 4.0
60.3 x 5.2 7.02 141.3 x 8.6 323.9 x 4.8 37.8
76.1 x 4.0 141.3 x 9.3 323.9 x 5.2
76.1 x 4.8 141.3 x 9.5 30.9 323.9 x 5.5 43.1
76.1 x 5.2 168.3 x 4.0 16.2 323.9 x 5.7
76.1 x 5.5 168.3 x 4.8 19.4 323.9 x 6.0
76.1 x 5.7 168.3 x 5.2 323.9 x 6.4 50.1
76.1 x 6.0 168.3 x 5.5 323.9 x 6.6
76.1 x 6.4 168.3 x 5.7 323.9 x 7.1 55.0
76.1 x 6.6 168.3 x 6.0 323.9 x 8.2 64.2
76.1 x 7.1 168.3 x 6.4 25.5 323.9 x 8.6 66.9 Features:
88.9 x 4.0 8.37 168.3 x 6.6 323.9 x 9.3
• Dual Grade API 5L B/X42
88.9 x 4.8 10.5 168.3 x 7.1 28.2 323.9 x 9.5 73.7 and AS/NZS 1163: 2016
88.9 x 5.2 168.3 x 8.2 33.1 323.9 x 11.0 85.6 C350L0
88.9 x 5.5 11.3 168.3 x 8.6 323.9 x 12.7 97.5
88.9 x 5.7 168.3 x 9.3 323.9 x 14.0 108

88.9 x 6.0 168.3 x 9.5 38.3 323.9 x 15.1
88.9 x 6.4 168.3 x 11.0 42.6 323.9 x 16.0
88.9 x 6.6 219.1 x 4.0 21.2 355.6 x 4.25
88.9 x 7.6 15.2 219.1 x 4.8 25.4 355.6 x 4.8
101.6 x 4.0 219.1 x 5.2 355.6 x 5.2
101.6 x 4.8 219.1 x 5.5 29.0 355.6 x 5.5
101.6 x 5.2 219.1 x 5.7 355.6 x 5.7
101.6 x 5.5 219.1 x 6.0 355.6 x 6.0
|
101.6 x 5.7 13.5 219.1 x 6.4 33.6 355.6 x 6.4 55.1

Tubular
101.6 x 6.0 219.1 x 6.6 355.6 x 6.6

101.6 x 6.4 219.1 x 7.1 38.4 355.6 x 7.1
101.6 x 6.6 219.1 x 8.2 42.6 355.6 x 8.2
101.6 x 7.1 219.1 x 8.6 355.6 x 8.6
101.6 x 8.2 18.7 219.1 x 9.3 355.6 x 9.3
114.3 x 4.0 11.3 219.1 x 9.5 355.6 x 9.5 81.1
114.3 x 4.8 13.0 219.1 x 11.0 355.6 x 11.0
114.3 x 5.2 219.1 x 12.7 64.6 355.6 x 12.7 107
114.3 x 5.5 273.1 x 4.0 355.6 x 14.0
114.3 x 5.7 273.1 x 4.8 31.8 355.6 x 15.1
114.3 x 6.0 16.0 273.1 x 5.2 34.1 355.6 x 16.0
114.3 x 6.4 273.1 x 5.5 36.2 355.6 x 17.0
114.3 x 6.6 273.1 x 5.7 406.4 x 4.25
114.3 x 7.1 273.1 x 6.0 42.1 406.4 x 4.8
114.3 x 8.2 273.1 x 6.4 42.1 406.4 x 5.2
114.3 x 8.6 22.4 273.1 x 6.6 406.4 x 5.5
141.3 x 4.0 273.1 x 7.1 406.4 x 5.7
141.3 x 4.8 16.16 273.1 x 8.2 406.4 x 6.0
141.3 x 5.2 273.1 x 8.6 406.4 x 6.4 63.1
141.3 x 5.5 273.1 x 9.3 60.50 406.4 x 6.6
Steel Centre
141.3 x 5.7 273.1 x 9.5 406.4 x 7.1

141.3 x 6.0 273.1 x 11.0 406.4 x 8.2
141.3 x 6.4 273.1 x 12.7 81.60 406.4 x 8.6
141.3 x 6.6 21.9 273.1 x 14.0 406.4 x 9.3
38
KNOW YOUR STEEL
Structural CHS
Size Mass Size Mass Size Mass

d x t mm kg/m d x t mm kg/m d x t mm kg/m
406.4 x 9.5 93.0 508.0 x 6.0 610 x 16.0
406.4 x 11.0 508.0 x 6.4 79.2 610 x 17.0
406.4 x 12.7 123 508.0 x 6.6 610 x 19.0
406.4 x 14.0 508.0 x 7.1 660 x 6.0
406.4 x 15.1 508.0 x 8.2 660 x 6.4
406.4 x 16.0 508.0 x 8.6 660 x 6.6
406.4 x 17.0 508.0 x 9.3 660 x 7.1
457.0 x 4.8 508.0 x 9.5 117 660 x 8.2
457.0 x 5.2 508.0 x 11.0 660 x 8.6
457.0 x 5.5 508.0 x 12.7 155 660 x 9.3
457.0 x 5.7 508.0 x 14.0 660 x 9.5
457.0 x 6.0 508.0 x 15.1 660 x 11.0 Features:
457.0 x 6.4 71.1 508.0 x 16.0 660 x 12.7
• Dual Grade API 5L B/X42
457.0 x 6.6 508.0 x 17.0 660 x 14.0 and AS/NZS 1163 C350L0
Tubular
457.0 x 7.1 508.0 x 19.0 660 x 15.1
457.0 x 8.2 610 x 6.0 660 x 16.0
457.0 x 8.6 610 x 6.4 660 x 17.0
|
457.0 x 9.3 610 x 6.6 660 x 19.0
Structural CHS
457.0 x 9.5 105 610 x 7.1
457.0 x 11.0 610 x 8.2
457.0 x 12.7 139 610 x 8.6
457.0 x 14.0 610 x 9.3
457.0 x 15.1 610 x 9.5
457.0 x 16.0 610 x 11.0
457.0 x 17.0 610 x 12.7
508.0 x 5.5 610 x 14.0
508.0 x 5.7 610 x 15.1
Peace of Mind With DuraGal®

Given the diverse climate and geography of the Australian landscape, only a DuraGal® coating can
give you the peace of mind that you have the protection you need for the job at hand. DuraGal® can
be used in a variety of residential construction applications such as roof trusses, fencing, verandahs,
elevated flooring solutions and shade structures. It is also commonly applied across a variety of other
sectors including mining, commercial, engineering, manufacturing,
agriculture and transport.
Steel Centre
39
Steel Centre
Processing Capabilities
InfraBuild Steel Centre’s national network of branches gives you acess to
an expansive range of processing solutions combined with a large range
of products, project management and technical expertise.
InfraBuild Steel Centre’s comprehensive range of in-house processing
equipment and proven experience will assist you in reducing risk on your
projects whilst maximising the quality of results.
www.infrabuild.com
KNOW YOUR STEEL
Telescoping RHS
Female (Outer) Nominal Clearance Male (Inner)

d b t Top Side d b
mm mm mm mm mm mm mm
50 20 1.6
50 20 2.0
No section available
50 20 2.5
50 20 3.0
50 25 1.6
50 25 2.0
No section available
50 25 2.5
50 25 3.0
65 35 2.0 11.0 6.00 50 25
Side Clearance
65 35 2.5 10.0 5.00 50 25
Female
65 35 3.0 9.00 4.00 50 25
65 35 4.0 7.00 2.00 50 25
75 25 1.6 21.8 1.80 50 20
Tubular
75 25 2.0 21.0 1.00 50 20
75 25 2.5 20.0 0.00 50 20
75 50 1.6 6.80 11.8 65 35 Side
Male
Clearance
75 50 2.0 6.00 11.0 65 35
|
Telescoping RHS
75 50 2.5 5.00 10.0 65 35
75 50 3.0 4.00 9.00 65 35
Note: RHS is not a precision
75 50 4.0 2.00 7.00 65 35 tube and all dimensions
75 50 5.0 0.00 5.00 65 35 shown in the chart, although
in accordance with the
75 50 6.0 13.0 13.0 50 25 specifications, may vary
100 50 1.6 20.8 20.8 76 38 marginally within the tolerance
AVAILABLE WA ONLY
bands permitted.
100 50 2.0 20.0 20.0 76 38
100 50 2.5 19.0 19.0 76 38 Sizes shown in bold print are
sizes that provide a clearance of
100 50 3.0 18.0 18.0 76 38
less than 2.0mm. The internal
100 50 3.5 17.0 17.0 76 38 weld bead and variation in
corner radii between sections
100 50 4.0 16.0 16.0 76 38
will need to be considered when
100 50 5.0 14.0 14.0 76 38 closer fits are indicated. Where
telescoping over some length
100 50 6.0 12.0 12.0 76 38
is desired, additional allowance
125 75 2.0 21.0 21.0 100 50 may be needed for straightness.
125 75 2.5 20.0 20.0 100 50 For tight fits it is suggested
that some form of testing
125 75 3.0 19.0 19.0 100 50 be carried out prior to
125 75 4.0 17.0 17.0 100 50 committing material.
125 75 5.0 15.0 15.0 100 50

How to use this chart
125 75 6.0 13.0 13.0 100 50
See page 41
200 100 4.0 40.0 40.0 152 76
200 100 5.0 38.0 38.0 152 76 Note: See page 34 for Circular
Hollow Sections and 25 for
200 100 6.0 36.0 36.0 152 76
Square Hollow Sections.
200 100 9.0 30.0 30.0 152 76
250 150 5.0 40.0 40.0 200 100
250 150 6.0 38.0 38.0 200 100
250 150 9.0 32.0 32.0 200 100
Steel Centre
41
KNOW YOUR STEEL
Telescoping SHS

d b t Top Side d b
20 20 1.6 1.8 1.8
25 25 1.6 1.8 1.8 20 20
25 25 2.0 1.0 1.0 20 20
25 25 2.5 0.0 0.0 20 20
30 30 1.6 1.8 1.8 25 25
30 30 2.0 1.0 1.0 25 25
35 35 1.6 1.8 1.8 30 30
35 35 2.0 1.0 1.0 30 30
35 35 2.5 0.0 0.0 30 30
35 35 3.0 4.0 4.0 25 25
40 40 1.6 1.8 1.8 35 35 Side Clearance
40 40 2.0 1.0 1.0 35 35 Female
40 40 2.5 0.0 0.0 35 35
Telescoping SHS
40 40 3.0 4.0 4.0 30 30

40 40 4.0 2.0 2.0 30 30
50 50 1.6 6.8 6.8 40 40
50 50 2.0 6.0 6.0 40 40 Male Side
Clearanc
50 50 2.5 5.0 5.0 40 40
50 50 3.0 4.0 4.0 40 40
50 50 4.0 2.0 2.0 40 40 Note: SHS is not a precision tube
|
50 50 5.0 0.0 0.0 40 40 and all dimensions shown in the

Tubular
chart, although in accordance

65 65 1.6 11.8 11.8 50 50 with the specifications, may vary
65 65 2.0 11.0 11.0 50 50 marginally within the tolerance
bands permitted.
65 65 2.5 10.0 10.0 50 50
65 65 3.0 9.0 9.0 50 50 Sizes shown in bold print are
sizes that provide a clearance
65 65 4.0 7.0 7.0 50 50 of less than 2.0mm. The internal
65 65 5.0 5.0 5.0 50 50 weld bead and variation in
65 65 6.0 3.0 3.0 50 50 will need to be considered when
75 75 2.0 6.0 6.0 65 65 closer fits are indicated.
Where telescoping over some
75 75 2.5 5.0 5.0 65 65 length is desired, additional
75 75 3.0 4.0 4.0 65 65 allowance may be needed for
straightness. For tight fits it is
75 75 3.5 3.0 3.0 65 65 suggested that some form of
75 75 4.0 2.0 2.0 65 65 testing be carried out prior to
committing material.
75 75 5.0 0.0 0.0 65 65
75 75 6.0 13.0 13.0 50 50 How to use this chart
89 89 3.5 7.0 7.0 75 75 See page 41
89 89 5.0 4.0 4.0 75 75

Note: See page 34 for Circular
89 89 6.0 2.0 2.0 75 75 Hollow Sections and 27 for
90 90 2.0 11.0 11.0 75 75 Rectangular Hollow Sections.
90 90 2.5 10.0 10.0 75 75

100 100 2.0 7.1 7.1 89 89
100 100 2.5 6.1 6.1 89 89
100 100 3.0 5.1 5.1 89 89
100 100 4.0 3.1 3.1 89 89
100 100 5.0 1.1 1.1 89 89
Steel Centre
100 100 6.0 13.0 13.0 75 75

100 100 9.0 7.0 7.0 75 75
125 125 4.0 17.0 17.0 100 100
125 125 5.0 15.0 15.0 100 100
42
KNOW YOUR STEEL
Telescoping SHS

d b t Top Side d b
125 125 6.0 13.0 13.0 100 100
125 125 9.0 7.0 7.0 100 100
150 150 5.0 15.0 15.0 125 125
150 150 6.0 13.0 13.0 125 125
150 150 9.0 7.0 7.0 125 125
200 200 5.0 40.0 40.0 150 150
200 200 6.0 38.0 38.0 150 150
200 200 9.0 32.0 32.0 150 150
250 250 6.0 38.0 38.0 200 200
250 250 9.0 32.0 32.0 200 200
Side Clearance
Female
Tubular
1. Select the appropriate table for the type 4. Where two telescoping sections are being
of hollow section required. Select the size used, thickness should be similar and Male Side
|
Clearanc
of female (or outside) member closest will be determined by normal structural
Telescoping SHS
to your requirements for the left hand requirements. If a third section is to be
column. used, consideration of both clearance and
thickness within the size list available may Note: SHS is not a precision tube
and all dimensions shown in the
2. Depending on the application select be required. chart, although in accordance
the clearance required between the two with the specifications, may vary
members. Members may need to slide 5. RHS has the obvious advantage that its marginally within the tolerance
bands permitted.
freely inside each other, or be locked with shape prevents rotation of the sections.
a pin, spot welded or fixed with wedges. When pipe is used it may need to be fixed Sizes shown in bold print are
This means, in some cases, a ‘sloppy’ against twisting by welding or bolting. sizes that provide a clearance
fit may be suitable, while for others of less than 2.0mm. The internal
weld bead and variation in
the tightest fit possible may be more 6. Press Fit. For short pieces with no need corner radii between sections
appropriate. for separation or sliding an interference will need to be considered when
fit can be achieved using the available closer fits are indicated.
3. Having selected the most suitable ductility of the steel.
length is desired, additional
clearance for your application, take allowance may be needed for
Note: Sizes where clearance is shown as 0.0 will
the appropriate size of the male (inner) generally require press fit.
section from the right hand column, eg: suggested that some form of
testing be carried out prior to
• Female Section (outer) 75 x 75 x 3.0
• Clearance mm 4.0x4.0 Note: See page 34 for Circular
Hollow Sections and 27 for
• Male Section (inner) 65 x 65 Rectangular Hollow Sections.
Note: Clearance is total available difference between
member dimensions, not the gap on both sides.
Steel Centre
43
KNOW YOUR STEEL
Telescoping CHS

1. Select the size of female (or outside) 4. Where two telescoping sections are being
member closest to your requirements for used, thickness should be similar and
the left hand column. will be determined by normal structural
requirements. If a third section is to be
2. Depending on the application select used, consideration of both clearance and
the clearance required between the two thickness within the size list available may
members. Members may need to slide be required.
freely inside each other, or be locked with
a pin, spot welded or fixed with wedges. 5. Pipe may need to be fixed against
This means, in some cases, a ‘sloppy’ twisting by welding or bolting.
fit may be suitable, while for others
the tightest fit possible may be more 6. Press Fit. For short pieces with no need
appropriate. (See Note 6 Press Fit). for separation or sliding an interference
fit can be achieved using the available Clearance
3. Having selected the most suitable ductility of the steel.
clearance for your application, take Female
Note: Sizes where clearance is shown as 0.0 will
the appropriate size of the male (inner) generally require press fit.
section from the right hand column, eg: do Bore
Male
Telescoping CHS
• Female Section (outer) 76.1 x 5.9

• Clearance mm 2.6
• Male Section (inner) 60.3
Note: Clearance is total available difference between
member dimensions, not the gap on both sides. Note: Clearance =
(AS/NZS 1163 Min do - 2t) -
(AS/NZS 1163 Max do).
|
Tubular
Female (Outer) Male (Inner) Note: CHS is not a precision

tube and all dimensions
do t di Min. Clearance shown in the chart, although
DN Quality DN
mm x mm mm mm in accordance with the
specifications, may vary
20 Extra LIght 26.9 x 2.0 15 21.3 0.4 marginally within the tolerance
25 Extra Light 33.7 x 2.0 20 26.9 1.6 bands permitted.
25 Light 33.7 x 2.6 20 26.9 0.4
Sizes shown in bold print are
25 Medium 33.7 x 3.2 15 21.3 4.8 sizes that provide a clearance of
25 Heavy 33.7 x 4.0 15 21.3 3.2
32 Extra Light 42.4 x 2.0 25 33.7 3.5 corner radii between sections
32 Light 42.4 x 2.6 25 33.7 2.3
closer fits are indicated.
32 Medium 42.4 x 3.2 25 33.7 1.1 Where telescoping over some
32 Heavy 42.4 x 4.0 20 26.9 6.3 length is desired, additional
allowance may be needed for
40 Extra Light 48.3 x 2.3 32 42.4 0.1 straightness. For tight fits it is
40 Light 48.3 x 2.9 25 33.7 7.6 suggested that some form of
40 Medium 48.3 x 3.2 25 33.7 7.0 committing material.
40 Heavy 48.3 x 4.0 25 33.7 5.4
40 Extra Heavy 48.3 x 5.4 25 33.7 2.6
50 Extra Light 60.3 x 2.3 40 48.3 6.4
50 Light 60.3 x 2.9 40 48.3 5.2
50 Medium 60.3 x 3.6 40 48.3 3.8
50 Heavy 60.3 x 4.5 40 48.3 2.0
50 Extra Heavy 60.3 x 5.4 40 48.3 0.2
Steel Centre
44
KNOW YOUR STEEL
Telescoping CHS
Circular Hollow Sections (CONTINUED)
Female (Outer) Male (Inner)

do t di Min. Clearance
DN Quality DN
mm x mm mm mm
65 Extra Light 76.1 x 2.3 50 60.3 9.8
65 Galtube® Plus 76.1 x 2.6 50 60.3 9.2
65 Light 276.1 x 3.2 50 60.3 8.0
65 Medium 76.1 x 3.6 50 60.3 7.2
65 Heavy 76.1 x 4.5 50 60.3 5.4
65 Extra Heavy 76.1 x 5.4 50 60.3 2.6
80 Extra Light 88.9 x 2.6 65 76.1 6.0
80 Light 88.9 x 3.2 65 76.1 4.8
80 Medium 88.9 x 4.0 65 76.1 3.2
80 Heavy 88.9 x 5.0 65 76.1 1.2 Clearance
80 Extra Heavy 88.9 x 5.9 50 60.3 15.3

Female
90 Extra Light 101.6 x 2.6 80 88.9 5.6
90 Light 101.6 x 3.2 80 88.9 4.4
do Bore
Tubular
90 Medium 101.6 x 4.0 80 88.9 2.8 Male
90 Heavy 101.6 x 5.0 80 88.9 0.8

100 Extra Light 114.3 x 3.2 90 101.6 4.1
100 Light 114.3 x 3.6 90 101.6 3.3
|
Telescoping CHS
100 Medium 114.3 x 4.5 90 101.6 1.5
Note: Clearance =
100 Heavy 114.3 x 5.4 80 88.9 12.6
(AS/NZS 1163 Min do - 2t) -
125 Extra Light 139.7 x 3.0 100 114.3 16.9 (AS/NZS 1163 Max do).
125 Light 139.7 x 3.5 100 114.3 15.9
125 Medium 139.7 x 5.0 100 114.3 12.9 Note: CHS is not a precision
tube and all dimensions
125 Heavy 139.7 x 5.4 100 114.3 12.1 shown in the chart, although
150 Light 165.1 x 3.0 125 139.7 15.4 in accordance with the
specifications, may vary
150 Medium 165.1 x 5.0 125 139.7 12.4 marginally within the tolerance
150 Heavy 165.1 x 5.4 125 139.7 11.6 bands permitted.
Sizes shown in bold print are

sizes that provide a clearance of
closer fits are indicated.
length is desired, additional
allowance may be needed for
suggested that some form of

See page 41
Steel Centre
45
KNOW YOUR STEEL
End Colour Codes

Square and Rectangular sections (RHS)
Wall Thickness
Colour
mm
Violet 1.6
Chocolate Brown 1.8
Yellow 2.0
Silver 2.3
Pink 2.5
Gold 2.8
Dark Blue 3.0
Grey 3.5
Green 4.0 Note: Meets AS/
NZS 4496:1997
Orange 5.0 (Recommended practice
White 6.0 for the colour coding of
steel products).
Pink 7.0
Red 8.0
Violet 9.0
End Colour Codes
End Colour Codes

Circular Sections (CHS)
|
Tubular
Colour Gauge
Green end Extra light (XL)
Yellow end Light (L)
Blue end Medium (M)
Red end Heavy (H)
Cream end Extra heavy (XH)
Note: Meets AS/NZS

4496:1997 (Recommended
practice for the colour
coding of steel products).
Steel Centre
46
Plate
KNOW YOUR STEEL

Flat Plate
Grade 250
Thickness Mass Width Length kg/lineal metre

mm kg/m mm m of plate width
5 39.25 2400 6.0 94.2
5 39.25 2400 9.0 94.2
5 39.25 3000 9.0 117
6 47.10 2400 6.0 11
6 47.10 2400 9.0 11
6 47.10 3000 9.0 141
6 47.10 3200 12.0 151
8 62.80 1800 6.0 113 Typical Uses:
8 62.80 2400 6.0 151
8 62.80 2400 9.0 151 • General fabrication
8 62.80 3000 9.0 188 • Structural members
8 62.80 3200 12.0 201 • High-rise buildings
10 78.50 1800 6.0 141 • Bridges
10 78.50 2400 6.0 188 • Storage tanks
Plate
10 78.50 2400 9.0 188
10 78.50 3000 9.0 236
10 78.50 3200 12.0 251
Features:
|
12 94.20 1800 6.0 170 • Meets AS/NZ 3678:2016.
Flat Plate
12 94.20 2400 6.0 226 (Structural Steel, Hot Rolled
12 94.20 2400 9.0 226 Floor Plates & slabs).
12 94.20 3000 6.0 283 • A medium strength
12 94.20 3000 9.0 283 structural steel plate product
12 94.20 3200 12.0 301
with nominal yield strength
of 250 MPa
16 125.60 1800 6.0 226
16 125.60 2400 6.0 301
16 125.60 2400 9.0 301
16 125.60 3000 6.0 377
16 125.60 3000 9.0 377
16 125.60 3200 12.0 402
20 157.00 1800 6.0 283
20 157.00 2400 6.0 377
20 157.00 2400 9.0 377
20 157.00 3000 9.0 471
20 157.00 3200 12.0 502
25 196.25 1800 6.0 353
25 196.25 2400 6.0 471
25 196.25 2400 9.0 471
25 196.25 3000 9.0 589
25 196.25 3200 12.0 628
28 219.80 2400 6.0 528
28 219.80 2400 9.0 528
32 251.20 1800 6.0 452
32 251.20 2400 6.0 603
32 251.20 2400 9.0 603
32 251.20 3000 9.0 754
36 282.60 2400 6.0 678
Steel Centre
36 282.60 2400 9.0 678

40 314.00 1800 6.0 565
40 314.00 2400 6.0 754
40 314.00 2400 9.0 754
47
KNOW YOUR STEEL
Flat Plate
Grade 250

45 353 2400 6.0 848
45 353 2400 9.0 848
50 393 1800 6.0 707
50 393 2400 6.0 942
50 393 2400 9.0 942
55 432 2400 6.0 1036
55 432 2400 8.4 1036
60 471 1800 6.0 848 Typical Uses:
60 471 2400 6.0 1130
70 550 1800 6.0 989 • General fabrication
70 550 2400 6.0 1319 • Structural members
80 628 1800 6.0 1130 • High-rise buildings
80 628 2400 5.2 1507 • Bridges
90 707 1800 6.0 1696 • Storage tanks
100 785 1800 5.6 1413
100 785 2400 4.0 1884
Features:
Flat Plate
110 864 1800 5.0 1554

110 864 2400 3.7 2072 • Meets AS/NZ 3678:2016.
120 942 1800 4.6 1696 (Structural Steel, Hot Rolled
120 942 2400 3.4 2261 Floor Plates & slabs).
|
130 1021 1800 4.2 1838 • A medium strength

Plate
130 1021 2400 3.1 2450 structural steel plate product

140 1099 1800 3.85 1978
with nominal yield strength
of 250 MPa
140 1099 2400 2.9 2638
150 1178 1800 3.6 2120
150 1178 2400 2.7 2826
XLERPLATE® Steel Plate

XELERPLATE® steel's consistent quality makes your manufacturing processes
more efficient, helping you maintain your quality assurance and enhances your
reputation as a supplier of high-calibre products.
Steel Centre
48
KNOW YOUR STEEL
Flat Plate
Grade 350

5 39.3 2400 6.0 94.2
5 39.3 2400 9.0 94.2
5 39.3 3000 9.0 118
6 47.1 2400 9.6 113
8 62.8 2400 9.6 151
10 78.5 2400 9.6 188
10 78.5 3100 9.6 243
12 94.2 2400 9.6 226
Typical Uses:
12 94.2 3100 9.6 292
16 126 2400 9.6 301 • General fabrication
16 126 3100 9.6 389 • Structural members
20 157 2400 9.6 377 • High-rise buildings
20 157 3100 9.6 487
• Bridges
25 196 2400 9.6 471
• Storage tanks
Plate
32 251 2400 9.6 603
40 314 2400 7.6 754
50 393 2400 7.6 942 Features:
|
60 471 2400 7.6 1130
Flat Plate
• Meets AS/NZ 3678: 2016
70 550 2400 6.0 1319 (Structural Steel, Hot Rolled
80 628 2400 5.5 1507 Floor Plates & slabs).
90 707 2400 6.3 1696 • A medium strength
90 707 2400 3.15 1696 structural steel plate product
100 785 2100 6.5 1649 with nominal yield strength
100 785 2100 3.25 1649 of 350 MPa
Plate Processing
InfraBuild Steel Centre can offer various plate processing options including
Oxy profiling and bevelling, Plasma cutting, Flame cutting and cropping.
We can also cut shapes, letters and numbers.
Applications include: Stripping, bevel cutting, stitch cutting, notching,
punching, shearing & cropping.
Steel Centre
49
KNOW YOUR STEEL
Plate
K1042 Plate

12 94.20 2400 6.0 226
16 125.60 2400 6.2 301
20 157.00 2400 6.0 377
25 196.25 2400 6.0 471
32 251.20 2400 6.3 603
40 314.00 2400 7.6 754
50 392.50 2400 6.0 942
60 471.00 2400 6.0 1130
70 549.50 2400 5.8 1319
80 628.00 2400 5.0 1507

• General engineering parts • Meets AS/NZS 3678: 2016 -
• Profile cut gears K1042
• Wear/abrasion applications • A heat treatable plate grade for
Flat Plate
general engineering applications

|
Plate
Pressure Vessel Plate

AS1548-PT430T
5 39.25 2400 9.0 94.2
AS1548-PT460T
6 47.10 3100 9.6 146
AS1548-PT460NR
8 62.80 3100 9.6 195
10 78.50 3100 9.6 243
12 94.20 3100 9.6 292
Typical Uses:
16 125.60 3100 9.6 389
20 157.00 3100 8.6 4867 • Boiler
25 196.25 3100 9.6 608 • Pressure Vessel
32 251.20 2400 9.6 603
40 314.00 2400 9.6 754 Features:
50 392.50 2400 7.6 942
60 471.00 2400 6.0 1130 • Meets AS 1548:2008
70 549.50 2400 6.0 1319 (Fine grained, weldable
steel plates for pressure
80 628.00 2400 5.2 1507
equipment)
90 706.50 2400 5.2 1696
• A fully killed, fine grained,
100 785.00 2400 5.2 1884
carbon-manganese steel
with a guaranteed minimum
Steel Centre
tensile strengthJ
50
KNOW YOUR STEEL
Floor Plate
XLERPLATE® Grade 250 Steel
Non-Stock
Thickness Mass Width Length Pack Mass lengths
mm kg/m2 mm m tonnes
mm kg/LM
6 48.60 1800 6.0 1.9 6 87.5
8 64.80 1800 6.0 1.4 8 117
10 80.50 1800 6.0 1.2 10 145
12 96.20 1800 6.0 1.0 12 173
Features:
• Meets AS/NZS 1594: 2002 • Hot rolled structural product with
Meets AS/NZS 1365: 1996 - HA250 minimum yield strength of 250MPa;
(Flat rolled steel products) good ductility and good weldability
Plate
|
Coil Plate
Coil Plate
TRU-SPEC™ HA250
Non-Stock
mm kg/LM
3 23.550 1200 2.4 2 3 28.3
3 23.550 1200 6.0 2 3 28.3
3 23.550 1500 3.0 2 3 35.3
3 23.550 1500 6.0 2 3 35.3
4 31.400 1200 2.4 2 4 37.7
4 31.400 1500 3.0 2 4 47.1
4 31.400 1500 6.0 2 4 47.1
5 39.250 1200 2.4 2 5 47.1 Typical Uses:
5 39.250 1500 3.0 2 5 58.9
• Brake press forming applications
5 39.250 1500 6.0 2 5 58.9
• General fabrication
6 47.100 1200 2.4 2 6 56.5
6 47.100 1500 3.0 2 6 70.7
• Laser cutting
6 47.100 1500 6.0 2 6 70.7
8 62.800 1200 2.4 2 8 75.4 Features:
8 62.800 1500 3.0 2 8 94.2
• Meets AS/NZS 1594: 2002
10 78.500 1200 2.4 2 10 94.2
Meets AS/NZS 1365: 1996
10 78.500 1500 3.0 2 10 118
• Hot rolled structural product
12 94.200 1200 2.4 2 12 113
with minimum yield strength of
12 94.200 1500 3.0 2 12 141 250MPa; good ductility and good
weldability
Steel Centre
51
KNOW YOUR STEEL
Floor Plate
TRU-SPEC™ HA250
Non-Stock
mm kg/LM
3 25.550 1200 2.4 2 3 30.7
3 25.550 1200 6.0 2 3 30.7
5 41.250 1200 2.4 2 5 49.5
5 41.250 1200 6.0 2 5 49.5
5 41.250 1500 6.0 2 5 61.9
6 49.100 1200 6.0 2 6 58.9
6 49.100 1500 6.0 2 6 73.7
8 64.800 1500 6.0 2 8 97.2

• Floorplate • Meets AS/NZS 1594: 2002
Meets AS/NZS 1365: 1996 - HA250
(Flat rolled steel products)
• Hot rolled structural product with
Coil Plate
minimum yield strength of 250MPa;

good ductility and good weldability
|
Plate
Coil Plate
TRU-SPEC™ HA350
Non-Stock
2
mm kg/m mm m tonnes
mm kg/LM
5 39.250 1500 8.0 2 5 58.9
6 47.100 1200 6.0 2 6 56.5
6 47.100 1500 6.0 2 6 70.6
8 62.800 1200 6.0 2 8 75.4
Features:
Meets AS/NZS 1365: 1996
• Hot rolled structural product
with minimum yield strength of
350MPa; good ductility and good
weldability
Steel Centre
52
Wear Plate
KNOW YOUR STEEL

BISALLOY®
BISALLOY® BISALLOY® BISALLOY®

Wear 320 steel Wear 400 steel Wear 450 steel
Thickness Mass
mm kg/m2 Tensile strength: Tensile strength: Tensile strength:
Typical - 1070 MPA Typical - 1320 MPA Typical - 1400 MPA
5 39.3 2400 x 8000 2400 x 8000

6 47.1 1525 x 8000 1526 x 8000 2400 x 8000
6 47.1 2485 x 8000 2485 x 8000 2400 x 8000
8 62.8 2485 x 8000 2486 x 8000 2485 x 8000
10 78.5 2485 x 8000 2485 x 8000 2485 x 8000
10 78.5 3100 x 8000 3100 x 8000 3100 x 8000
12 94.2 2485 x 8000 2485 x 8000 2485 x 8000
12 94.2 3100 x 8000 3100 x 8000 3100 x 8000
Typical Uses:
16 125 2485 x 8000 2485 x 8000 2485 x 8000
16 125 3100 x 8000 3100 x 8000 3100 x 8000 • Demolition tools
20 157 2485 x 8000 2485 x 8000 2485 x 8000 • Ground engaging tools
20 157 3100 x 8000 3100 x 8000 3100 x 8000 • Earthmoving buckets
25 196 2485 x 8000 2485 x 8000 2485 x 8000 • Drag Line buckets
25 196 3100 x 8000 3100 x 8000 3100 x 8800
• Wear plates
Plate
32 251 2485 x 8000 2485 x 8000 2485 x 8500
• Chutes
40 314 2485 x 8000 2485 x 8000 2485 x 8000
50 393 2485 x 8000 2485 x 8000 2485 x 8000
|
60 471 2485 x 6000 2485 x 6000 2485 x 6000
Wear Plate
70 549 1900 x 6000 1900 x 6000 1900 x 6000
75 589 1900 x 6000 1900 x 6000 1900 x 6000
80 628 1900 x 6000 1900 x 6000 1900 x 6000
90 706 1600 x 6000 1600 x 6000 1900 x 6000
100 785 1525 x 6000 1525 x 6000 1525 x 6000
BISALLOY® Wear BISALLOY® Wear

Thickness Mass 500 steel 600 steel
mm kg/m2 Tensile strength: Tensile strength:
Typical - 1640 MPA Typical - 2050 MPA
8 62.8 2485 x 8000
10 78.5 2485 x 8000
10 78.5 2485 x 8000
12 94.2 2485 x 8000 2400 x 8000
12 94.2 2485 x 8000 2400 x 8000
16 126 2485 x 8000 2400 x 8000
16 126 2485 x 8000 2400 x 8000
20 157 2485 x 8000 2400 x 8000
20 157 2485 x 8000 2400 x 8000
25 196 2485 x 8000 2400 x 8000
25 196 2485 x 8000 2400 x 8000
32 251 2485 x 8000 2400 x 8000
40 314 2485 x 8000 2400 x 8000
50 393 2485 x 8000 2400 x 6000
60 471 2485 x 6000
70 549 1900 x 6000
75 589 1900 x 6000
80 628 1900 x 6000
Steel Centre
90 706 1525 x 6000

100 785 1525 x 6000
53
Structural Plate
KNOW YOUR STEEL
BISALLOY®
BISALLOY® BISALLOY® BISALLOY® BISALLOY® BISALLOY®

Structural Structural Structural Structural Structural
60 steel 70 steel 80 steel 100 steel 110 steel
Thickness Mass
mm kg/m2 Tensile Tensile Tensile Tensile Tensile
strength: strength: strength: strength: strength:
Typical - 640 Typical - 760 Typical - 830 Typical - 1000 Typical - 1100
MPA MPA MPA MPA MPA
5 39.3 1525 x 8000 1525 x 8000 1525 x 8000 1525 x 8000
6 47.1 1525 x 8000 1525 x 8000 1525 x 8000 1525 x 8000 1525 x 8000
6 47.1 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
8 62.8 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
10 78.5 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
10 78.5 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000
12 94.2 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
12 94.2 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000
16 126 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
16 126 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000
20 157 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
20 157 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000
25 196 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
25 196 3100 x 8000 3100 x 8000 3100 x 8000 3100 x 8000
Structural Plate
32 251 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000

40 314 2485 x 8000 2485 x 8000 2485 x 8000 2485 x 8000
50 393 2485 x 8000 2485 x 8000 2485 x 8000
60 471 2485 x 6000 2485 x 6000 2485 x 6000
70 549 1900 x 6000 1900 x 6000 1900 x 6000
75 589 1900 x 6000 1900 x 6000 1900 x 6000
80 628 1900 x 6000 1900 x 6000 1900 x 6000
|
90 706 1600 x 6000 1600 x 6000 1600 x 6000

Plate
100 785 1525 x 6000 1525 x 6000 1525 x 6000
Typical Uses:
• Transport Equipment such as Low Loaders
• Structural Components for Mining Dump Trucks and
other Mobile Equipment
• Mining Equipment Roll Over Protection Systems (ROPS)
• Underground Longwall Mining Supports
• Storage Tanks for water, oil and gas
• Columns for Low and High Rise Buildings
• Transfer Beams for Low and High Rise Buildings
• Road and Rail Bridge Beams and Columns
• Excavator Buckets
• Mobile Lifting Equipment
• Overhead Cranes
• Container Handling Equipment
Steel Centre
54
Sheet and Coil
KNOW YOUR STEEL

Sheet and Coil Thickness Terminology
B.M.T. vs. T.C.T. vs. T.P.T.
Paint
Metallic Coating
T.C.T B.M.T Base Steel T.P.T
Metallic Coating
Paint
When ordering through different suppliers or importing sheet & coil products, it is important to understand the
difference between B.M.T., T.C.T. & T.P.T.
B.M.T. = Base Metal Thickness. This excludes any coatings applied to the base metal sheet.
Sheet and Coil

T.C.T. = Total Coated Thickness. This measures both the base sheet and the coating. For example: Zincalume,
Galvanised, Zincanneal and Electro-Galv.
T.P.T. = Total Painted Thickness. This applies to painted sheets such as Colorbond and Signwhite.
This is only a factor in coated material and painted material. Manufactured painted products (ie. Colorbond) use a
metallic-coated base metal.
|
BRIGHTFORM® Sheet
Most suppliers quote base metal thickness, B.M.T. but it is important the user understands how different coatings will
change the thickness.
BRIGHTFORM® Sheet
Base Metal Thickness Width
kg/m2
mm mm
1.60 910 12.6
1.60 1210 12.6
1.60 1510 12.6
2.00 910 15.7
2.00 1210 15.7
2.00 1510 15.7
2.50 1210 19.6
2.95 1210 23.2
3.00 910 23.6
3.00 1210 23.6

• Tubing • Meets AS/NZS 1365: 1996 (Tolerances for
Steel Centre
• Shelving flat rolled steel products)

• Simple pressings • Pickled, skin-passed low carbon steel with
a good surface, suitable for bending and
• Hidden appliance panels
moderate drawing and pressing.
55
KNOW YOUR STEEL
Hot Rolled Sheet

Formable HA1S Steel
kg/m2
mm mm
1.50 1200 11.8
1.50 1210 11.8
1.60 910 12.6
1.60 1195 12.6
1.60 1200 12.6
1.60 1210 12.6
1.95 900 15.3
1.95 1195 15.3
1.95 1200 15.3
1.95 1210 15.3
2.40 1200 18.8 Typical Uses:
2.50 1195 19.6
• Shelving
2.50 1210 19.6
2.50 1495 19.6
• Light structural members
2.50 1510 19.6 • Tanks
2.90 1210 22.8
Features:
Hot Rolled Sheet
2.90 1500 22.8

2.95 1200 23.2
2.95 1500 23.2
(Flat rolled steel products)
2.95 1800 23.2
and AS/NZS 1365: 1996
3.00 895 23.6 (Tolerances for flat rolled
3.00 1195 23.6 steel products)
3.00 1210 23.6 • Skin-passed, Hot-rolled low
|
3.00 1495 23.6 carbon steel suitable for

Sheet and Coil
3.00 1510 23.6 simple forming, bending and

3.00 1800 23.6 welding operations.
Hot Rolled, Pickled and Oiled Sheet

HA3 Steel

kg/m2
mm mm
1.60 1210 12.6
2.00 910 15.7
2.00 1210 15.7
2.50 1210 19.6
3.00 1210 23.6
4.00 1210 31.4
5.00 1210 39.3
6.00 1210 47.1

• Agricultural machinery • Meets joint AS/NZS 1594: 2002 (Flat rolled
• Automotive components steel products) and AS/NZS 1365: 1996
(Tolerances for flat rolled steel products)
Steel Centre
• Sealed unit housings

• Hot rolled, formable steel suitable when
• Mower parts
pickled for medium drawing and heavy
• Brackets pressing operations.
• Furniture
56
KNOW YOUR STEEL
Cold Rolled Sheet
CA3SN-G

kg/m2
mm mm
0.60 1220 4.71
0.80 1220 6.28
1.00 1220 7.85
1.20 1220 9.42
1.50 1220 11.8
1.60 1220 12.6
2.00 1220 15.7
2.50 1220 19.6
3.00 1220 23.6

• Unexposed drawn parts for • Meets AS/NZS 1595: 1998 (Cold-rolled,
automotive and appliance unalloyed, steel sheet and strip)
end uses. • Cold rolled, skin-passed deep
Sheet and Coil

drawing steel guaranteed non-ageing
and free from stretcher stain with a general
purpose surface.
|
Cold Rolled Sheet
TRU-SPEC® Steel Plate
TRU-SPEC® steel is available in a range of structural grades, widths and lengths. Typically used in
light and standard structural members, brake press forming applications, light poles, trailer and
automotive components, general fabrications and galvanising applications.
The benefits of selecting TRU-SPEC® steel include:
• Guaranteed minimum strength levels
• Various levels of weldability, formability and ductility (Good and Excellent)
• Excellent for galvanising applications
• Enhanced weather resistance
BlueScope’s stretch levelling process provides a consistently flat and 'memory-free' product every
time particularly suited to the industry's growing preference towards laser cutting.

Steel Centre
57
KNOW YOUR STEEL
GALVABOND® Sheet
G2 Z275

kg/m2
mm mm
0.40 915 3.43
0.40 1220 3.43
0.45 915 3.82
0.50 1220 4.22
0.55 915 4.61
0.55 1200 4.61
0.55 1220 4.61
0.55 1500 4.61
0.60 1525 5.00
0.70 1220 5.79 Typical Uses:
0.75 915 6.18
0.75 1200 6.18 • Tube
0.75 1220 6.18 • Air conditioning ducts,
0.75 1500 6.18 • Air conditioning panels,
0.80 1525 6.57 • Meter boxes
0.90 915 7.36 • Trailers
GALVABOND® Sheet
0.90 1220 7.36

• Partitioning systems
0.95 1200 7.75
• Cable trays
0.95 1220 7.75
• Scaffolding planks
0.95 1500 7.75
• Rendering mesh
1.00 1220 8.14
1.00 1525 8.14 • Feeder troughs
1.10 915 8.92
1.10 1220 8.92 Features:
|
1.15 915 9.32

Sheet and Coil

1.15 1200 9.32
(Tolerances for flat rolled
1.15 1220 9.32
steel products) and AS 1397:
1.15 1500 9.32 2011 (Continuous hot-dip
1.20 1525 9.71 metallic coated steel sheet
1.50 915 12.1 and strip - Coatings of
1.50 1220 12.1 zinc and zinc alloyed with
1.50 1500 12.1
aluminium and magnesium)
1.55 1200 12.5 • Galvabond G2 steel is a
1.55 1220 12.5
hot-dipped zinc-coated
commercial forming steel
1.55 1500 12.5
with a spangled surface,
1.60 1525 12.9 suitable for general
1.90 1220 15.2 manufacturing. Product
1.95 1200 15.6 is suitable for moderate
1.95 1220 15.6 drawing applications and is
2.40 1220 19.1 suitable for lockseaming up
to 1.6mm thick.
2.45 1200 19.5
2.90 1220 23.1
Steel Centre
58
KNOW YOUR STEEL
ZINCANNEAL® Sheet
G2S ZF100

kg/m2
mm mm
0.50 1220 4.06
0.55 1220 4.45
0.70 1220 5.63
0.75 1220 6.02
0.80 1200 6.41
0.90 915 7.19
0.90 1220 7.19
0.95 1200 7.59
0.95 1220 7.59
1.00 1200 7.98
Note: hot-dipped zinc/iron alloy-coated
1.10 1200 8.77 commercial forming steel with a skin-
1.10 1220 8.77 passed smooth surface suitable for
direct-on painting. Some powdering
1.15 1200 9.16 of the coating may occur with severe
1.15 1220 9.16 deformation.
Sheet and Coil

1.20 1200 9.55
1.40 1220 11.1
1.50 915 11.9
1.50 1200 11.9
1.50 1220 11.9
1.55 1200 12.3
|
1.60 1200 12.7
ZINCANNEAL® Sheet
1.90 1220 15.1
1.95 1200 15.4

• Exposed painted panels • Meets AS/NZS 1365: 1996 (Tolerances for flat rolled
• Non-exposed steel products) and AS 1397: 2011 (Continuous
automotive panels hot-dip metallic coated steel sheet and strip -
Coatings of zinc and zinc alloyed with aluminium
• Washing machines
and magnesium)
• Acoustic ceiling tiles
• Zincanneal G2S is a matte manufacturing. Product
• Door frames is suitable for moderate drawing applications and is
• Switchboards suitable for lockseaming up to 1.6mm thick.
• Commercial fridges
& freezers
Steel Centre
59
KNOW YOUR STEEL
ZINCALUME® Sheet
G300 AZ150

kg/m2
mm mm
0.40 1200 3.31
0.55 1200 4.49
0.55 900 4.49
0.75 1200 6.06
1.00 900 8.02
1.00 1200 8.02
1.20 900 9.59
1.20 1200 9.59

• Rainwater goods • Meets AS/NZS 1365: 1996 (Tolerances for
• Gutters flat rolled steel products) and AS 1397: 2011
(Continuous hot-dip metallic coated steel sheet
• Garden sheds
and strip - Coatings of zinc and zinc alloyed with
aluminium and magnesium)
ZINCALUME® Sheet
• Zincalume G300 steel is a hot-dipped zinc/

aluminium alloy-coated structural steel with
a regular spangle surface and a guaranteed
minimum yield strength of 300MPa with good
ductility. Suitable for roll forming to a minimum
internal diameter of 1t.
|
Sheet and Coil
Steel Centre
60
KNOW YOUR STEEL
COLORBOND® Sheet
Grade 300
Size Mass
Colours
mm x mm x mm sheets/tonne
1200 x 2400 x 0.55 76
1200 x 3050 x 0.55 Manor Red® Jasper® Classic Cream™ Surfmist® 60

Paperbark® Dune® Shale Grey™ Windspray®
1200 x 3660 x 0.55 Woodland Grey® Pale Eucalypt® Wilderness® 51
Cottage Green® Monument™ Deep Ocean®
1200 x 2400 x 0.80 63
Ironstone® Evening Haze®
1200 x 3000 x 0.80 43
1200 x 2440 x 0.55 Appliance 76
1200 x 1800 x 0.55 Sign White 100

Note: All colours listed are trademarks
or registered trademarks of BlueScope
• Roofing & accessories • Colorbond prepainted steel is specifically
Steel Ltd.
Sheet and Coil

• Wall cladding designed by BlueScope Steel to provide a
high durability, premier cladding and roofing
• Rainwater goods.
material for general use.
COLORBOND® Steel Standard Colour Range
|
COLORBOND® Sheet
Classic Cottage Evening
Basalt® Bluegum® Deep Ocean® Dover White™ Dune®
Cream™ Green® Haze®
Pale
GullyTM Ironstone® Jasper® Manor Red® Monument® Night Sky® Paperbark®
Eucalypt®
Woodland
Shale Grey™ Southerly® Surfmist® Terrain® Wallaby® Windspray®
Grey®
Steel Centre
The printed steel colours shown here have been reproduced to represent actual colours as
accurately as possible. However we recommend checking your chosen colour against an
actual product sample before purchasing as varying light conditions and print limitations
affect colour tones.
61
Reinforcing Bar and Mesh
KNOW YOUR STEEL
HANDIMESH®
Galvanized
Product Std Longitudinal Cross Mass Dimensions
Code Unit Wires* Wires* (kg) (m)
G112A Sheet 97 x 2.5 @ 25 121 x 2.5 @ 25 22 3 x 2.4
G122A Sheet 97 x 2.5 @ 25 61 x 2.5 @ 50 17 3 x 2.4
G113 Sheet 97 x 3.2 @ 25 121 x 3.2 @ 25 36 3 x 2.4
G123 Sheet 97 x 3.2 @ 25 61 x 3.2 @ 50 27 3 x 2.4
G234 Sheet 49 x 4 @ 50 41 x 4 @ 75 24 3 x 2.4
G235 Sheet 49 x 5 @ 50 41 x 5 @ 75 38 3 x 2.4
G224 Sheet 49 x 4 @ 50 61 x 4 @ 50 29 3 x 2.4
G225 Sheet 49 x 5 @ 50 61 x 5 @ 50 45 3 x 2.4
G445 Sheet 25 x 5 @ 100 31 x 5 @ 100 23 3 x 2.4
G445A Sheet 25 x 5.6 @ 100 31 x 5.6 @ 100 29 3 x 2.4
G465A Sheet 25 x 5.6 @ 100 21 x 5.6 @ 150 24 3 x 2.4
* Number of Wires x Diameter (mm) @ Spacing (mm)

• General Purpose Applications • Also available in ‘bright wire’ on request.
• DIY & Home Improvement
Mesh
UTEMESH®
|
Ribbed Square Mesh

8 x 6 @ 200
SL62UTE Sheet 20 x 6 @ 200 18 4x2
+4 x 4.24 @ 100
8 x 6.75 @ 200
SL72UTE Sheet 20 x 6.75 @ 200 23 4x2
+4 x 4.75 @ 100
8 x 7.6 @ 200
SL82UTE Sheet 20 x 7.6 @ 200 30 4x2
+4 x 5.35 @ 100

• Residential Construction • AS/NZS 4671 - Steel for the reinforcement of concrete
• Driveways and paths • Versatile and lightweight Note: *AS/NZS 4671 – Steel for the
• Shed slabs • Minimises wastage reinforcement of concrete UTEMESH® has
been designed to conform to road traffic
• Smaller concreting jobs • Can be handled by one person authorities’ regulations for transportation
(using the correct handling techniques) of oversize products. UTEMESH® can also be
handled by one person using the appropriate
• Safe and legal to transport lifting techniques. Now safer to handle with
reduced flying ends (reduced to 20 mm). Up
• Easy to setup, place and tie to 8% improved mesh cover through lap
efficiency across and along the sheet.
ONEMESH®
Ribbed Rectangular Mesh
RL718 Sheet 25 x 6.75 @ 100 30 x 7.6 @ 200 67 6 x 2.4
RL818 Sheet 25 x 7.6 @ 100 30 x 7.6 @ 200 79 6 x 2.4
RL918 Sheet 25 x 8.6 @ 100 30 x 7.6 @ 200 93 6 x 2.4
Steel Centre
RL1018 Sheet 25 x 9.5 @ 100 30 x 7.6 @ 200 109 6 x 2.4

RL1118 Sheet 25 x 10.7 @ 100 30 x 7.6 @ 200 130 6 x 2.4
RL1218 Sheet 25 x 11.9 @ 100 30 x 7.6 @ 200 157 6 x 2.4
Features: AS/NZS 4671 - Steel for the reinforcement of concrete

62
KNOW YOUR STEEL
ONEMESH®
Ribbed Square Mesh
10 x 6 @ 200
SL62 Sheet 30 x 6 @ 200 33 6 x 2.4
+4 x 4.24 @ 100
10 x 6.75 @ 200
SL72 Sheet 30 x 6.75 @200 41 6 x 2.4
+4 x 4.75 @ 100
SL81 Sheet 25 x 7.6 @ 100 60 x 7.6 @ 100 105 6 x 2.4
10 x 7.6 @ 200
SL82 Sheet 30 x 7.6 @ 200 52 6 x 2.4
+4 x 5.35 @ 100
10 x 8.6 @ 200
SL92 Sheet 30 x 8.6 @ 200 66 6 x 2.4
+4 x 6 @ 100
10 x 9.5 @ 200
SL102 Sheet 30 x 9.5 @ 200 80 6 x 2.4
+4 x 6.75 @ 100
SL53 6 x 4.75 @ 300
Sheet 20 x 4.75 @ 300 14 6 x 2.3
(WA ONLY) +4 x 4.75 @ 100
SL63 6 x 6 @ 300
Sheet 20 x 6 @ 300 21 6 x 2.3
(WA ONLY) +4 x 4.75 @ 100

Plain Square Mesh
F411 Roll 25 x 4 @ 100 601 x 4 @ 100 290 60 x 2.4
F41ST Roll 23 x 4 @ 100 601 x 4 @ 100 275 60 x 2.4
F41 Sheet 25 x 4 @ 100 61 x 4 @ 100 29 6 x 2.4
|
Mesh
Features: Multi-purpose square mesh
Trench Mesh
Product Std Longitudinal Mass Dimensions
Code Unit Wires* (kg) (m)
L8TM200 Sheet 3 x 7.6 @ 100 6.8 6 x 0.2
L8TM300 Sheet 4 x 7.6 @ 100 9.2 6 x 0.3
L8TM400 Sheet 5 x 7.6 @ 100 11.6 6 x 0.4
L8TM500 Sheet 6 x 7.6 @ 100 13.9 6 x 0.5
L11TM200 Sheet 3 x 10.7 @ 100 13.3 6 x 0.2
L11TM300 Sheet 4 x 10.7 @ 100 17.7 6 x 0.3
L11TM400 Sheet 5 x 10.7 @ 100 22.3 6 x 0.4
L11TM500 Sheet 6 x 10.7 @ 100 26.8 6 x 0.5
L12TM200 Sheet 3 x 11.9 @ 100 15.8 6 x 0.2
L12TM300 Sheet 4 x 11.9 @ 100 21.2 6 x 0.3
L12TM400 Sheet 5 x 11.9 @ 100 26.5 6 x 0.4
L12TM500 Sheet 6 x 11.9 @ 100 31.9 6 x 0.5
Steel Centre
FTM16200 Sheet 3 x 16 @ 100 30.6 6 x 0.2

FTM16300 Sheet 4 x 16 @ 100 41.1 6 x 0.3
63
KNOW YOUR STEEL
Deformed Reinforcing Bar

Class N
Mass Length
Product Code
kg/m (m/t)
N10S 0.64 1552
N12S 0.93 1077
N16S 1.65 605
N20S 2.58 387
N24S 3.71 269
N28S 5.05 198
N32S 6.59 151
N36S 8.35 119
N40S 10.3 97
Note: Calculated mass includes an allowance for rolling manufacturing variations as per our Terms
and Conditions. N40S is available only on request – Lead time required. AS/NZS 4671 - Steel for the
reinforcement of concrete.
Deformed Reinforcing Bar
Reinforcing Accessories
Danley Tape
Product Code Type Width (mm) Length (m)
STEGOST95 Seaming Tape 95 55

STEGOCT75 Claw Tape 75 55
|
STEGOTT51 Tack Tape 51 15
Plastic Mesh Chairs Clipfast
Product Code Height (mm) No./Bag
PC20M 20
PC25M 25
PC30M 30
PC32M 32
100
PC40M 40
PC50M 50
PC65M 65
PC75M 75
Steel Centre
64
KNOW YOUR STEEL
Plastic Bar Chairs
Product Code Height (mm) No./Bag
COM2540 25 or 40
COM5065 50 or 65
COM5065C 50 or 65
COM7590 75 or 90
COM7590C 75 or 90
COM85100 85 or 100
COM105110 105 or 110 100
COM115120 115 or 120
COM125130 125 or 130
COM135140 135 or 140
COM145150 145 or 150
COM155160 155 or 160
COM165170 165 or 170

C = Clip on

• Slab on ground • Sets concrete cover
• Polystyrene pod slab • Dual heights
• Swimming pools • Clip-on mechanism for stability
• Integrated base to minimise puncture of
polythene film
|
Tie Wire Roll
Product Code Wire Diameter (mm) Length (m) Approximate
TW 1.6 60
TW5 1.6 320
TW10 1.6 650
TW315 3.15 16
Tie Wire Belt Pack Black
BP1.4 1.4 100

BP1.5 1.5 93
Tie Wire Belt Pack Galvanised
BP1.5GAL 1.5 93
Steel Centre
Note: Large range of reinforcing accessories available - contact your local InfraBuild Steel Centre branch for assistance.
65
KNOW YOUR STEEL
Aluminium
Aluminium Circular Tube
Size Length Alloy / Weight

Die
mm x mm m Temper Kg
12 x 1.6 EX5004 6.5 6060 T5 0.917
16 x 1.6 EX5006 6.5 6060 T5 1.268
19 x 1.2 E40149 6.5 6060 T5 1.177
20 x 1.6 EX5008 6.5 6060 T5 1.575
25 x 1.6 EX5010 6.5 6060 T5 1.908
25 x 3.0 EX5011 6.5 6060 T5 3.64
32 x 1.6 EX5013 6.5 6060 T5 2.685
32 x 3.0 EX5014 6.5 6060 T5 4.428
38.09 x 3.25 EX2078 6.0 6060 T5 5.76
38.1 x 3.25 E40016 6.5 6060 T5 6.247
40 x 3.0 EX5017 6.5 6060 T591 6.123
44.45 x 3.25 EX2101 6.0 6060 T591 6.816
46 x 3.5 E40700 6.0 6060 T591 7.572
Note: * Sizes not available in all states
48.41 x 4.47 EX2202 6.0 6005A T5 9.996
Aluminium Circular Tube
50 x 1.6 EX5018 6.5 6060 T5 4.271

50 x 2.0 EX5019 6.5 6060 T591 5.291
50 x 3.0 EX5041 6.5 6082 T5 7.176
50 x 4.0 EX5081 6.5 6082 T5 9.366
50 x 6.0 E40545 6.5 6060 T5 13.428
60 x 2.0 EX5021 6.5 6063 T6 1.968
60 x 3.0 EX5022 6.5 6060 T591 9.425
60 x 5.0 EX5071 6.5 6060 T591 15.165
63.5 x 3.95 E40098 6.0 6060 T4 6.384
76.19 x 4.75 EX2207 6.5 6060 T1 17.256
|
76.19 x 6.35 EX2153 6.5 6005 T5 24.453

Aluminium
76.2 x 3.2 EP13843 6.5 6060 T4 12.678

76.2 x 3.8 EP8552 6.5 6060 T5 15.171
80 x 3.0 EX5024 6.5 6060 T5 12.734
88.9 x 5.33 EX2161 6.5 6060 T5 22.668
100 x 3.0 EX5026 6.5 6060 T5 16.042
Steel Centre
66
KNOW YOUR STEEL
Aluminium Rectangular Tube
Size Length Weight

Die Alloy / Temper
mm x mm m Kg
38 x 25 x 1.5 RAD E22174 6.5 6106 T6 3.06
40 x 20 x 2.0 RAD E22169 6.5 6060 T5 3.89
40 x 25 x 2.5 EB1014 6.5 6060 T5 5.27
40 x 25 x 3.0 RAD E22122 6.5 6060 T5 6.09
50 x 25 x 1.6 EQ3359 6.5 6060 T5 4.03
50 x 25 x 2.5 EU7751 6.5 6060 T5 6.14
50 x 25 x 3.0 EL8012 6.0 6082 T5 6.71
50 x 25 x 3.0 RAD EW5373 6.5 6060 T5 7.13
50 x 40 x 3.0 EL8013 6.5 6082 T5 8.85
60 x 40 x 3.0 EL8015 6.5 6060 T5 9.90
65 x 16 x 1.2 RAD EQ6823 6.5 6060 T5 3.22
65 x 16 x 1.4 RAD EQ6948 6.5 6060 T5 3.74
75 x 50 x 3.0 EL8017 6.5 6060 T5 12.5
76.2 x 25.4 x 2.4 EL4238 6.5 6060 T5 8.16 Note: * Sizes not available in all states
Aluminium
76.2 x 50.8 x 1.6 EQ1915 6.0 6060 T5 6.42
80 x 25 x 3.0 EL8018 6.5 6060 T5 10.4
80 x 40 x 3.0 EL8019 6.5 6060 T5 12.0
80 x 50 x 3.0 EL8020 6.5 6060 T5 13.1
100 x 25 x 2.5 EL8021 6.5 6060 T5 10.5
|
100 x 25.2 x 1.60 EQ2698 6.5 6060 T5 6.85
Aluminium Rectangular Tube

100 x 40 x 3.0 EL8023 6.5 6060 T5 14.1
100 x 50 x 1.6 EL8024 6.5 6060 T5 8.24
100 x 50 x 1.6 EP8087 6.5 6106 T6 8.25
100 x 50 x 3.0 EL8025 6.5 6063 T5 6.48
100 x 50 x 3.0 RAD E22177 6.0 6082 T5 14.0
100 x 50 x 6 RAD EB1592 6.0 6082 T5 10.7
101.6 x 76.2 x 2.29 RAD EG5074 8.0 6060 T5 16.8
125 x 40 x 3.0 EL8028 6.5 6060 T5 16.7
125 x 50 x 3.0 EL8030 6.5 6060 T5 17.8
150 x 50 x 3.0 EL8033 6.5 6060 T5 20.4
150 x 50 x 3.0 RAD E22178 6.5 6063 T5 20.5
200 x 50 x 3.0 EL8035 6.5 6060 T5 7.91
250 x 50 x 3 E22173 6.5 6106 T6 21.4
Steel Centre
67
KNOW YOUR STEEL
Aluminium Square Tube
Size Length Alloy / Weight

Die
mm x mm m Temper Kg
19.05 x 1.2 EK1333 6.5 6060 T5 1.50
20 x 1.6 E22101 6.5 6060 T5 2.07
20 x 3.0 EL2299 6.5 6060 T5 3.58
20 x 3.0 RAD E51872 6.5 6060 T591 3.44
25 x 1.5 RAD EL8819 6.5 6060 T5 2.48
25 x 1.6 E22103 6.5 6060 T5 2.63
25 x 2.0 RAD EN3238 6.5 6060 T5 3.23
25 x 3.0 EL8003 6.5 6060 T5 4.64
25 x 3.0 RAD E22120 6.5 6060 T5 4.50
25 x 3.0 RAD EQ4067 6.5 6060 T591 4.64
32 x 3.0 EL8005 6.5 6060 T5 6.11
40 x 1.6 EL7938 6.5 6060 T5 4.32
40 x 2 RAD EQ6818 6.5 6060 T5 5.21
40 x 2.0 EQ4000 6.5 6060 T5 5.34 Note: * Sizes not available in all states
Aluminium Square Tube
40 x 3.0 E22108 6.5 6060 T5 7.79

40 x 3.0 RAD E73599 6.5 6060 T5 7.70
45 x 2.5 E22109 6.5 6060 T5 7.46
50 x 1.6 EQ2259 6.5 6060 T5 5.43
50 x 1.6 RAD EQ6446 6.6 6060 T6 5.25
50 x 2.0 EB1003 6.5 6060 T5 6.74
50 x 2.5 EL8008 6.5 6060 T5 8.34
50 x 3.0 EB1004 6.5 6060 T5 9.90
50.8 x 3.18 RAD EL6217 6.5 6060 T5 10.5
65 x 2.5 EQ6382 6.5 6060 T5 11.0
|
65 x 3.0 RAD EU2011 6.5 6060 T5 13.1

Aluminium
75 x 3.0 RAD EQ6032 6.5 6060 T5 14.8

76 x 6.35 RAD EQ4171 6.0 6082 T6 26.4
76.2 x 6.35 RAD E11077 6.5 6005A T5 28.7
80 x 6 RAD E22129 6.0 6085 T5 28.8
Steel Centre
68
KNOW YOUR STEEL
Aluminium Angles
Length
A B T Die Alloy / Temper Mass/LEN
m
20 20 1.6 EK9107 6060 T5 6.5 1.07
20 20 3.0 EK9108 6060 T5 6.5 1.95
25 12 1.6 RAD EK9109 6060 T5 6.5 0.65
25 20 1.6 EK9111 6060 T5 6.5 1.22
25 25 1.6 EK9216 6060 T5 6.5 1.36
25 25 3.0 EK9217 6060 T5 6.5 2.48
32 20 1.6 EK9114 6060 T5 6.5 1.42
32 32 1.6 EB1126 6060 T5 6.5 1.75
32 32 3.0 EK9118 6060 T5 6.5 3.21
40 20 1.6 EL3257 6060 T5 6.5 1.64
40 20 3.0 EK9121 6060 T5 6.5 3.00
40 25 1.6 EL8124 6060 T5 6.5 1.78
40 25 3.0 EK9122 6060 T5 6.5 3.26
40 40 1.6 EK9123 6060 T5 6.5 2.20
Aluminium
40 40 3.0 EK9124 6060 T5 6.5 4.06
40 40 6.0 EK9126 6060 T5 6.5 7.79
50 25 1.6 EK9129 6060 T5 6.5 2.06
50 25 3.0 EK9130 6060 T5 6.5 3.79
50 40 3.0 EK9131 6060 T5 6.5 4.58
|
50 50 1.6 EL9417 6060 T5 6.5 2.76
Aluminium Angles
50 50 3.0 EK9132 6060 T5 6.5 5.11
50 50 6.0 EK9134 6060 T5 6.5 9.90
50 50 6.0 RAD EN5408 6060 T5 6.0 9.19
60 60 3.0 EK9135 6060 T5 6.5 6.61
60 60 6.0 EK9136 6060 T5 6.5 12.0
70 25 1.6 EN5714 6060 T5 6.5 2.61
70 40 1.6 EN7492 6060 T5 6.5 3.04
75 25 3.0 EL5923 6060 T5 6.5 5.12
76.2 50.8 6.35 RAD EG6410 6060 T5 6.0 12.8
76.2 76.2 3.2 E06168 6060 T5 6.5 8.31
80 20 3.0 EK9137 6060 T5 6.5 5.10
80 50 2.5 E20559 6060 T5 6.5 5.60
80 80 6.0 EK9138 6060 T5 6.5 16.2
100 50 3.0 EP12372 6060 T5 6.5 7.74
100 50 4.0 E20525 6060 T5 6.5 10.3
100 50 6.0 RAD EQ1558 6060 T5 6.5 14.1
100 100 6.0 EP12627 6060 T5 6.5 18.9
125 50 3.0 EK9139 6060 T5 6.5 9.06
125 50 6.0 RAD E20700 6060 T5 6.5 16.5
Steel Centre
69
KNOW YOUR STEEL
Aluminium Channels
Alloy / Length
A B C T1 T2 Die Mass/LEN
Temper m
10 10 10 1.6 EK9146 6060 T5 6.5 0.75
12 12 12 1.6 EK9149 6060 T5 6.5 0.92
12 20 20 2.5 EK9151 6060 T5 6.5 2.06
16 16 16 1.6 EK9152 6060 T5 6.5 1.26
20 20 20 1.6 EL1812 6060 T5 6.5 1.59
20 20 20 3 EK9155 6060 T5 6.5 2.84
22.32 20 20 1.2 RAD EN4619 6060 T5 6.5 1.29
25 12 12 3 EK9156 6060 T5 6.5 2.26
25 25 25 1.6 EL5249 6060 T5 6.5 2.02
25 25 25 3 EK9158 6060 T5 6.5 3.63
25 40 40 3 EK9159 6060 T5 6.5 5.21
32 16 16 1.6 E20784 6060 T5 6.5 1.70
32 25 25 3 EK9160 6060 T5 6.5 4.00
40 20 20 2 EQ1556 6060 T5 6.5 2.67
Aluminium Channels
40 20 20 3 EK9161 6060 T5 6.5 3.89

40 25 25 3 EK9162 6060 T5 6.5 4.42
40 40 40 3 E20790 6060 T5 6.5 6.00
44.45 25.4 25.4 3.18 EG1021 6060 T5 6.5 4.96
50 25 25 3 EK9215 6060 T5 6.5 4.95
50 50 50 3 EK9163 6060 T5 6.5 7.58
53 25 25 1.5 E20830 6060 T5 6.5 2.43
54.2 20 20 1.6 E20821 6060 T5 6.5 2.56
60 32 32 3 EK9164 6060 T5 6.5 6.21
|
Aluminium
76.2 38.1 38.1 RAD EG6435 6060 T5 6.5 16.4

80 25 25 3 EK9165 6060 T5 6.5 6.53
80 40 40 4 EK9166 6060 T5 6.5 10.7
80 40 40 4 RAD E20921 6060 T5 6.5 9.88
80 40 40 6 RAD E20922 6060 T5 6.5 14.5
100 25 25 3 EK9168 6060 T5 6.5 7.58
100 50 50 3 EB1208 6060 T5 6.5 10.2
100 50 50 5 RAD EN3527 6060 T5 6.5 19.5
100 50 50 6 RAD 9 EN3528 6060 T5 6.5 26.6
100 50 50 7.56 RAD EP13664 6060 T5 6.5 #N/A
101.6 50.8 50.8 7.9 RAD 6.3 EG6434 6060 T5 6.5 22.5
Steel Centre
70
KNOW YOUR STEEL
Aluminium Tees
Size Length Alloy /

Die Mass/LEN
mm x mm m Temper
20 x 20 x 1.6 EK9140 4.0 6060 T5 0.66
25 x 25 x 1.6 EK9142 6.5 6060 T5 1.36
25 x 25 x 3.0 EK9143 6.5 6060 T5 2.48
35 x 50 x 3.0 RAD EU9284 6.0 6082 T6 4.05
40 x 40 x 1.6 EL5287 6.5 6060 T5 2.20
40 x 40 x 3.0 EK9144 6.5 6060 T5 4.06
40 x 40 x 4.0 RAD EU9187 6.0 6082 T6 5.02
45 x 100 RAD EU7074 9.65 6082 T6 21.5
50 x 156 x 6.0 RAD EU8408 9.65 6082 T6 31.3
50 x 25 x 1.6 E20212 6.5 6060 T5 2.06
50 x 50 x 4.0 RAD E20219 6.0 6082 T6 6.32
50 x 50 x 6.0 RAD E20205 6.0 6082 T6 9.31
50 x 60 RAD EU6368 6.0 6082 T6 8.47
50 x 70 RAD EN5331 9.65 6082 T6 17.1
Aluminium
80 x 139 RAD EU7545 6.0 6082 T6 21.7
80 x 163 RAD EN5218 6.0 6082 T6 23.6
|
Aluminium Tees and Rounds
Aluminium Round Bar
Length Alloy /
Diameter Die Mass/LEN
m Temper
10 EX6000 4.0 6060 T5 0.85
12 EX6001 4.0 6060 T5 1.22
16 EX6002 4.0 6060 T5 2.17
20 EX6003 4.0 6060 T5 3.39
25.4 EX3000 4.0 6060 T5 5.48
33 EX6005 4.0 6061 T6 9.24
39 EX6006 4.0 6061 T6 12.9
Aluminium | Aluminium Tees

Steel Centre
71
KNOW YOUR STEEL
Aluminium Flat Bars
Size Length Alloy /

Die Mass/LEN
mm x mm m Temper
20 x 3 EX4004 4.0 6060 T5 0.65
20 x 6 EX4020 4.0 6060 T5 1.30
25 x 3 EX4005 4.0 6060 T5 0.81
25 x 6 EX4021 4.0 6060 T5 1.62
32 x 3 EX4006 4.0 6060 T5 1.04
32 x 6 EX4022 4.0 6060 T5 2.07
32 x 10 EX4030 4.0 6060 T5 3.46
40 x 3 EX4007 4.0 6060 T5 1.30
40 x 6 EX4023 4.0 6060 T5 2.59
40 x 10 EX4031 4.0 6060 T5 4.32
50 x 3 EX4008 4.0 6060 T5 1.62
50 x 6 EAL4035 4.0 6060 T5 3.24
50 x 6 RAD EX4024 4.0 6060 T5 3.23
50 x 10 EX4032 4.0 6060 T5 5.40
Aluminium Flat and Square Bars
50 x 12 EX4039 4.0 6060 T5 6.48

60 x 3 EX4009 4.0 6060 T5 1.94
60 x 6 EX4069 4.0 6060 T5 3.89
60 x 10 EX4070 4.0 6060 T5 6.48
60 x 12 EX4040 4.0 6060 T5 7.78
80 x 3 EX4010 4.0 6060 T5 2.59
80 x 6 EX4025 4.0 6060 T5 5.18
80 x 10 EX4033 4.0 6060 T5 8.64
80 x 12 EX4041 4.0 6060 T5 10.4
80 x 16 EX4044 4.0 6060 T5 13.8
100 x 1.5 RAD E34113 3.75 6060 T5 1.52
100 x 3 EX4011 4.0 6060 T5 3.24
100 x 6 EX4026 4.0 6060 T5 6.48
|
100 x 10 EX4034 4.0 6060 T5 10.8

Aluminium
100 x 12 EX4042 4.0 6060 T5 13.0

160 x 6 EX4027 4.0 6060 T5 10.4
160 x 10 EX4035 4.0 6060 T5 17.3 Note: * Sizes not available in all states
Aluminium Square Bars

Size Length Alloy /
Die Mass/LEN
mm x mm m Temper
6x6 EX6500 4.0 6060 T5 0.39
10 x 10 EX6501 4.0 6059 T5 1.08
12 x 12 EX6502 4.0 6060 T5 1.56
16 x 16 EX6503 4.0 6060 T5 2.77
20 x 20 EX6504 4.0 6060 T5 4.32
25 x 25 EX6505 4.0 6060 T5 6.75
40 x 40 EX6506 4.0 6106 T6 17.0
Steel Centre
72
KNOW YOUR STEEL
Aluminium Sheet and Plate
Sheet 5005 H34
Thickness Width Length

kg/sheet
mm mm m
0.60 1200 2.4 4.66
0.80 1200 2.4 6.22
1.00 1200 2.4 7.78
1.20 1200 2.4 9.33
1.60 1200 2.4 12.4
2.00 1200 2.4 15.5
2.00 1200 3.0 19.4
2.00 1500 3.6 29.2
2.50 1200 2.4 19.4
3.00 1200 2.4 23.3
3.00 1200 3.0 29.2
3.00 1500 3.0 36.3
3.00 1500 3.6 43.7
4.00 1200 2.4 31.1
Aluminium
5.00 1200 2.4 38.9
6.00 1200 2.4 46.6
|
PVC Coated 5005 H34

kg/sheet
mm mm m
1.20 1200 2.4 9.33
1.60 1200 2.4 12.4
2.00 1200 2.4 15.5
2.50 1200 2.4 19.4
3.00 1200 2.4 23.3

Grade kg/sheet
mm mm m
1.60 1200 2.4 12.4
2.00 1200 2.4 15.4
5052 H32
2.50 1200 2.4 19.4
3.00 1200 2.4 23.3
5251 H34 2.50 1500 3.0 30.2
Steel Centre
73
KNOW YOUR STEEL
Aluminium Tread Plate

3003 H22 - Propellor Bright

kg/sheet
mm mm m
1.60 1219 2.438 12.9
2.00 1219 2.438 17.1
3.00 1219 2.438 27.2
4.76 1219 2.438 45.0

5052 H114 - 5BAR

kg/sheet
mm mm m
1.60 1200 2.4 13.2
2.00 1200 2.4 17.0
2.00 1500 3.0 26.5
2.50 1200 2.4 21.3
2.50 1500 3.0 33.3
|
3.00 1200 2.4 25.3

Aluminium
3.00 1200 6.0 63.4

3.00 1500 3.0 39.6
3.00 1500 6.0 80.3
4.00 1200 2.4 33.1
4.00 1200 6.0 82.4
4.00 1500 6.0 103
5.00 1200 2.4 39.7
5.00 1200 3.66 62.0
5.00 1200 6.0 102
5.00 1500 6.0 127
6.00 1200 2.4 47.8
6.00 1500 3.0 74.7
Steel Centre
74
Stainless Steel
KNOW YOUR STEEL

Stainless Steel Angles
Grades 304, 316
Size Mass
mm x mm kg/m
25 x 25 x 3 1.13
25 x 25 x 5 1.77
25 x 25 x 6 2.06
30 x 30 x 3 1.36
30 x 30 x 5 2.17
30 x 30 x 6 2.53
30 x 30 x 5 1.02
30 x 30 x 6 1.21
40 x 40 x 3 1.85
40 x 40 x 5 2.98
40 x 40 x 6 3.49
50 x 50 x 3 2.36
50 x 50 x 5 3.79
50 x 50 x 6 4.46
Stainless Steel
|
Stainless Steel Sheet and Coil
Stainless Steel Angles

Austentic
Thickness Range Width
Grade
mm mm
316 0.55 to 6.00 914, 1219, 1500, 1525
304 0.55 to 6.00 914, 1219, 1500, 1525
Ferritic
Thickness Range Width
Grade
mm mm
Note: Range of Stainless Steel includes:
430 0.55 to 0.9 914, 1219 Grades: 304, 304L, 316, 316L
Finishes: 2B, No. 4 Polished, bright
annealed
Steel Centre
75
KNOW YOUR STEEL
Stainless Steel Flat Bars

Grades 304, 316
Size Mass
mm x mm kg/m
12 x 3 0.29
12 x 6 0.58
20 x 3 0.49
20 x 5 0.81
20 x 6 0.98
25 x 3 0.61
25 x 5 1.02
25 x 6 1.21
25 x 10 2.04
25 x 12 2.45
32 x 3 0.77
32 x 5 1.30 Note: Range of Stainless Steel includes:
32 x 6 1.57 Grades: 304, 304L, 316, 316L
32 x 10 2.62
Stainless Steel Flat Bars
40 x 3 0.98
40 x 5 1.61
40 x 6 1.96
40 x 10 3.27
40 x 12 3.92
50 x 3 1.21
50 x 5 2.04
50 x 6 2.45
50 x 10 4.08
|
50 x 12 4.90
Stainless Steel
65 x 5 2.61
65 x 6 3.18
65 x 10 5.31
75 x 5 3.06
75 x 6 3.68
75 x 10 6.04
75 x 12 7.25
100 x 6 4.91
100 x 10 8.18
Steel Centre
76
KNOW YOUR STEEL
Stainless Steel Round Bars
Grades 304, 316 & 430
Size Mass
mm x mm kg/m
3.18 0.06
4.76 0.14
6.35 0.25
7.94 0.39
9.00 0.50
10.0 0.62
12.0 0.89
12.7 0.99
15.9 1.55
16.0 1.58
19.1 2.24
20.0 2.47
22.2 3.04
24.0 3.55
Stainless Steel
25.4 3.98
30.0 5.55
31.8 6.21
32.0 6.31
35.0 7.55
38.1 8.94
|
40.0 9.86
Stainless Steel Round Bars

44.5 12.2
50.8 15.9
54.0 17.9
57.2 20.1
63.5 24.9
66.7 27.4
69.9 30.1
76.2 35.8
82.6 42.0
88.9 48.7
101.6 63.6
127 99.4
Steel Centre
77
Walkway Systems
KNOW YOUR STEEL
InfraBuild Steel Centre have partnered with leading suppliers Webforge

and Nepean Building & Infrastructure to supply walkway systems as either
fully prefabricated custom panels or as standard components. Grating,
handrail and components are available in mild steel, aluminium, stainless
steel, or corrosion/chemical resistant fibreglass reinforced plastic (FRP).
Stanchion and handrail products are available in a range of mounting
configurations to suit mounting for: platform, stairway, side mount, side
offset, conveyor, cored, weld-on, or bolt-on style.
FRP Grating
FRP grating is composed of 65% resin and 35% continuous glass fibres,
available in stock panels 3660 x 1220 with 6 mm load bar configurations
in a range of depths and sizes in green or yellow and a grey “Mini-mesh”.
The high resin content makes FRP resistant to a wide range of corrosive
chemicals, gases and fumes. Other properties that make FRP a valuable
choice in dangerous work areas are its fire retardant, non-sparking, and
Grating and Flooring
non-conductive properties. FRP is simple to cut and assemble on site

with standard tools. Ancillary items recommended for site assembly are
stainless steel mounting brackets, and sealing kits to seal cut edges.
Drainage Grates
InfraBuild Steel Centre offers a range of standard (stock) and custom
made mild steel drainage and trench grates that comply with AS3996.
|
Walkway Systems
Grates are rated to:

Class A: Extra light duty – suit pedestrian/cyclists
Class B: Light duty – suit light vehicles/tractors, livestock
Class C: Medium duty – suit malls and pedestrian areas open to slow
moving commercial vehicles
Class D: Heavy Duty – suit roads and areas open to commercial vehicles
Composite Flooring
Composite flooring comprises of floorplate welded to the top of grating
(shown right), and is available in mild steel or aluminium. Another option is
a composite comprised of grating with a light gauge mesh welded to the
underside to prevent tools or small objects from falling through the grating.
Expanded Walkway Mesh

Made from 5mm mild steel, walkway mesh is a strong, cost effective
solution for high impact and load applications. 3000mm long panels are
available in stock widths of 1200/900/750/600mm. 45mm SWM x 135mm
LWM and 30mm SWM x 75mm LWM configurations available.
Steel Centre
78
KNOW YOUR STEEL
Stair Stringers
Weldlok® stair stringers are available configured for 2 to 17 How to calculate the number
treads. Treads and mounting brackets can be purchased
separately. Advantages of pre-assembled stringers
of treads required
• Convenient and easy to install 1. Measure the vertical height from the ground to the
• Hot-dip galvanised to AS/NZS 4680 finished floor level of the landing.
• Standard with 175mm rise and 250mm going at 2. Divide the height by the rise (175mm)
an angle of 35 degrees 3. Round the result to the nearest whole number, then
• Designed to take a maximum tread width of 1000mm reduce by 1 for the top landing.
i.e. Height = 1000 divided by 175 = 5.71 rounded to 6 and
reduced by 1 = 5 step stringers required.
Vertical
Weldlok® Number RHS Thickness Weight per Pair
Height
Product Code of Steps (mm) (kg)
(mm)
G1TS 1 350 3.0 10
G2TS 2 525 3.0 15
Walkway Systems
G3TS 3 700 3.0 19
Accessory
G4TS 4 875 3.0 25
G5TS 5 1050 3.0 30
G6TS 6 1225 4.0 35
G7TS 7 1400 4.0 41
G8TS 8 1575 4.0 46
G9TS 9 1750 4.0 52
|
Stair Stringers
G10TS 10 1925 4.0 58
G11TS 11 2100 4.0 61
G12TS 12 2275 4.0 66 Notes:
G13TS 13 2450 5.0 107 * Treads must be >50mm thick
* Treads must not be greater than 1000mm wide
G14TS 14 2625 5.0 116
* When installing the stringers, in order to comply with the
G15TS 15 2800 5.0 124 Building Code of Australia, the "rise" of each tread must
be consistent, including the first step and the last step
G16TS 16 2975 5.0 132
up to the landing platform. This may require the ground
G17TS 17 3150 5.0 140 level to be built up.
Weldlok® Mastermesh® Galintel® Galserv®
Australia’s leading integrated manufacturers of metal products www.nepean.com

Steel Centre
79
KNOW YOUR STEEL
Stair Treads
Stair treads are made to measure from mild steel, aluminium, stainless steel, or FRP with options
of non slip nosing. Suitable for either bolt-on or weld-on attachment.
Weldok® stair treads can be supplied in Series 30, 40 & 60 forgebar grating.
Treads may be selected using the Recommended Width and Recommended Max. Length tables.
Non-standard treads can also be supplied on request. Please consult our sales department.
Type T1 Type T2 Type T3 Type T4
Mild steel with floor plate nosing,

Welded fixing, no nosing Mild steel bolted fixing Bolted fixing, floor plate nosing
welded fixing
Type T5 Type T6 FRP

Stair Treads
Aluminium with abrasive nosing, Bolted fixing, Holed End Plates, FRP tread with abrasive nosing,
welded fixing abrasive Nosing bolted fixing
|
Walkway Systems
Ordering Stair Treads

1. Select from the tread types shown (T1 to T6).
2. Refer to Recommended Max. Lengths table. Select a Load Bar Size and Series with a maximum length equal to or greater
than the required tread length. For example, if the required tread length is 1100mm, the Series 40 grating with 32 x 5 load
bars (A40-325) would be appropriate.
3. From the Recommended Widths table, choose a width that corresponds to the tread type and Series selected. For
example, based on the Series 40 grating and a T1 tread, the tread width would be either 125, 165, 205, 245, 285
or 325mm. Example would be: Tread Type T1 ~ 1100 x 285 from A40 – 325
Recommended Maximum Lengths (mm) Recommended Widths (mm)

Load Bar Size 25 x 5 32 x 5 40 x 5 Tread Types T1 to T6
Series 30 900 1300 1600 Series 30 125 155 185 215 245 275 305
Series 40 750 1200 1500 Series 40 125 165 205 245 285 325
Series 60 500 800 1300 Series 60 125 185 245 305
Bolted Connections Standard End Plates for Bolted Threads
End Plate Hole Centres (mm)

'A' 45 75 75 100 100 100 100
Steel Centre
Standard Stocked Treads (serrated):

600 x 285mm
750 x 285mm
900 x 245mm
Note: Special End Plate Hole Centres available on request.
900 x 275mm
80
KNOW YOUR STEEL
Non-Weld Handrail Systems
Top Rail
101 - Short Tee 104 - Long Tee 128 - Corner (Top Rail) 125 - 90 degree elbow
Suit Pipe Product code Suit Pipe Product code Suit Pipe Product code Suit Pipe Product code
32NB 101-C42 32NB 104-C42 32NB 128-C42 32NB 125-C42
40NB 101-D48 40NB 104-D48 40NB 128-D48 40NB 125-D48
48NB/32NB 101-D48/C42 40NB 104-D48 40NB 128-D48 48NB/32NB 125-D48/C42
Walkway Systems
Middle Rail
|
116 - Corner (Middle Rail)
119 - Cross (Middle Rail) 150 - Internal Expanding Joint
Suit Pipe Product code Suit Pipe Product code Suit Pipe Product code
32NB 116-C42 32NB 119-C42 32NB 150-C42
40NB 116-D48 40NB 119-D48 40NB 150-D48
Elbows & Knuckles
124 - Variable Elbow 15 - 60 degrees 166 - Adjustable knuckle 173 - Single Swivel Combination
Steel Centre
32NB 124-C42 32NB 166-C42 32NB 173-C42

40NB 124-D48 40NB 166-D48 40NB 173-D48
81
KNOW YOUR STEEL
Bases
232 - Heavy Duty

242 - Base Flange with
Railing Base Flange 246 - Heavy Duty Side Palm
Toe Board Fixing
32NB 232-C42 32NB 242-C42 32NB 246-C42
40NB 232-D48 40NB 242-D48 40NB 246-D48
Access Systems
|
Walkway Systems
745 - DDA Assist Expanding 746 - DDA Assist Saddle

766 - Adjustable elbow
Wall Bracket Wall Bracket
32NB 745-C42 32NB 746-C42 32NB 766-C42
*Will also fit 40NB *Will also fit 40NB *Will also fit 40NB
Note: In order to meet the requirements of accessability standards, the range forms flush joints with size 32NB tube.
Steel Centre
82
Build a better floor with a
DuraGal Flooring System®
Whether you're building a deck or a whole house, the DuraGal Flooring System® is assembled on-site and requires
no welding. Simple screwed connections make construction fast and easy.
DuraGal Flooring System® meets the industry durability guideline by including fully-galvanised Australian-made
tubular sections, which are corrosion resistant and won’t rot, warp or twist.
The strength of steel also allows for greater spans and reduces the impact of site works and sediment control issues.
KNOW YOUR STEEL
DuraGal Flooring System®
DuraGal Flooring System® building adhesive and gun-nailing. Most reputable nail tool
suppliers have hardened tipped nails to suit common nail guns to
DuraGal Flooring System® is a fully-engineered steel flooring attach sheet flooring to steel joists up to and including 2mm thick.
system developed to provide a fire-and-termite-resistant,
economical and easy-to-install alternative to conventional Spans
timber bearers and joists.
Joists are typically 100 x 50 x 1.6mm with continuous spans
of 2800mm and bearers are typically 150 x 50 x 2.0mm with
Easy to Install continuous spans of 3000mm. Other sizes may be specified
with differing spans subject to the floor layout and site
DuraGal Flooring System®M uses high strength C450L0 grade conditions. Your DuraGal Flooring System® distributor will be
galvanized DuraGal® ZB135/135 Hollow Sections. The sections able to nominate the most economical sizes and layout upon
are strong and lightweight making them easy to handle on site. receipt of the house plans.
DuraGal® ZB135/135 is easy to cut and drill, and best of all the
system has been designed so that it simply screws together on
Note: DuraGal Flooring System® requires independent engineering certification to
site using a screw gun fitted with a hex head bit. The DuraGal determine compliance of site specific conditions with statutory requirements.
Flooring System® features a range of speciality galvanized
fittings designed to allow you to get on with the job easily
and quickly. Fast and accurate levelling of the floor using the
adjustable piers during and after construction is a great feature.
Sheet flooring can still be attached in the traditional way using
DuraGal Flooring SystemTM
Typical sections of Bearer end support
DuraGal® ZB135/135 Blocking
Piers: 90 x 90 x 2.0mm
Bearers: 150 x 50 x 2.0mm Floor joist to bearer
Joists: 100 x 50 x 1.6mm
DuraGal® Pier
DING REQU
EL
W
IR
NO
ED
Pier to bearer connection
TO CONNE
SY C
EA
Pier to footing
Internal joiners Refer
DURAGAL® PLUSZB135/135
Pier adjustable top connection

End cap to bearer or joist
fits 90x90x2.0 DuraGal® SHS NOTE: Which type used will depend on
– 100mm on adjustment, the tie down requirements
Top bracing
NR maximum recommended
SIO ESIST <70mm Bottom bracing
RO – Suits 50mm wide bearers
AN
R
PRYDA®UNITIE
CO
– Maximum height 4.5m

T
®
DuraGal pier
90x90x2.0
Internal joiner
PRYDA® TRIPLE GRIPS

Pier bottom connection Double joists under
ITE RESISTA to suit 90x90x2.0 load bearing walls
RM DuraGal ® pier
NT
TE
4 hole Base Plate FDP-TBC-9020
PRYDA®PERGOLA ANGLES
PIER TO BEARER CONNECTION
ZONE SU
RE I
FI Adjustable top SPLIT LEVEL ARRANGEMENT
TA
H
fitting
BUS
(Not shown on main drawing)

BLE
DuraGal® Pier adjustable

joist
top connection
PIER TO FOOTING DETAIL DuraGal®bearer ®

DuraGal
PIER TO FOOTING DETAIL (upper level) joist
Pier bottom connection
CAL LARGE Masonry anchors 50mm min

MI
O
Depth to engineers
50mm min
SP
ECON
specifications Verandah
ANS
Masonry Sleeve DuraGal® bearer

anchors (lower level)
100mm min
(may be precast)
Footing to engineers specification. DuraGal® pier
Finished 50mm above ground level
Steel Centre
and trowelled level. Not included in

quotation Width or diameter to
engineers specifications
84
KNOW YOUR STEEL
DuraGal®
Mezzanine Flooring System
DuraGal® Mezzanine Flooring System DuraGal® Mezzanine Flooring System
• A user friendly system that can save you time in construction,
offers:
reducing the disruption to your business. • A high strength, lightweight steel flooring system which can be
• On-site assembly without welding, only normal tools such as used to increase the floor area of existing or new buildings.
cut-off saws and Tek screw guns are required. • The system can also allow for the height of the columns to
• High tensile strength and light weight sections allowing for be adjusted, therefore compensating for any variations in
a wider spacing of the bearers and, with the ]larger span the slab, with adjustment being available before or after
distances between columns, under-floor areas are still usable installation.
with large open areas for uses such as workshops, office • Columns, bearers and joists are all galvanised to be practically
accommodation and storage areas etc. maintenance free.
• All connections are either screwed or nailed. DuraGal® Mezzanine Flooring System uses high strength
• Effectively increases storage capabilities C450L0 grade galvanised DuraGal® ZB135/135. The sections are
• Long lasting and virtually maintenance free strong and lightweight making them easy and safe to handle
on site. The DuraGal® Mezzanine Flooring System is designed
• Minimum fabrication required
using a range of speciality fittings to allow safe and easy
• Minimum welding construction.
• Low cost
DuraGal® Mezzanine Flooring System

DING REQU RE
ZONE SU NR
SIO ESIST
EL FI I RO
W
IR
TA
AN
H
R
NO
ED
CO
BUS
BLE
CAL LARGE ITE RESISTA TO CONNE

MI RM
SY C
EA
O
SP
NT
T
TE
ECON
ANS
Steel Centre
85
Building Products
KNOW YOUR STEEL
Lintels - Traditional
Quick Selection and Safe Load Tables
Quick Selection Tables
Category
A B C D E
Description
Lightweight timber truss,

Cavity wall equally Lightweight sheet roof Load-bearing internal
Non-load bearing brick tiled roof and sheet
supported on both skins. and ceiling supported on brickwork under upper
veneer with separate ceiling supported on
(Supported roof span single skin. (Supported storeys. (Supported floor
structural timber frame single skin. (Supported
<8m) roof span <8m) span <8m)
roof span <8m)
Clear Span Length (mm)

Traditional Angle * Follow the colour code from the loading categories above. Add end bearing of 100-150mm to both ends of span
Category
100 x 75 x 10 - 13kg/m
900 1200 1500 1800 2100 2400 2700 3000
A
B
C
D
|
E
Building Products

* Follow the colour code from the loading categories above.
Traditional Angle
Category Add end bearing of 100-150mm to both ends of span
150 x 100 x 10 - 19kg/m
2100 2400 2700 3000 3300 3600 4000
A
B
C
D
E
Steel Centre
86
KNOW YOUR STEEL
Traditional Angle Clear Span Length (mm)

Category All tables are intended as a guide. Qualified expert advice should be sought in deciding the suitability of
100 x 75 x 10 - 13kg/m any structural product for a construction application. UDL = Uniform Distributed Load
Span (mm) 900 1200 1500 1800 2100 2400 2700

Bar Length (mm) 1200 1500 1800 2100 2400 2700 3000
Total Load (kg) 1345 1005 805 670 575 500 415
UDL (kg/m) 1494 840 538 373 274 210 154
Point Load (kg) 670 500 400 335 285 250 220
Traditional Angle Clear Span Length (mm)

150 x 100 x 10 - 19kg/m any structural product for a construction application. UDL = Uniform Distributed Load
Span (mm) 1800 2100 2400 2700 3000 3300 3600

Bar Length (mm) 2100 2400 2700 3000 3300 3600 4000
Total Load (kg) 3205 2355 1800 1425 1150 950 800
UDL (kg/m) 1781 1121 751 527 384 289 222
Building Products
Point Load (kg) 1690 1325 1010 800 645 535 450
• Loads limited by short term deflection of 1/600 span
Note: *Loads given are total (allowable) loads

including lintel and brickwork.
|
Steel Centre
87
KNOW YOUR STEEL
Lintels - Flat and Angle

Category
A B C D E
Description
Lightweight timber truss,

Cavity wall equally Lightweight sheet roof Load-bearing internal
Non-load bearing brick tiled roof and sheet
supported on both skins. and ceiling supported on brickwork under upper
veneer with separate ceiling supported on
(Supported roof span single skin. (Supported storeys. (Supported floor
structural timber frame single skin. (Supported
<8m) roof span <8m) span <8m)
roof span <8m)

Flat Bar * Follow the colour code from the loading categories above. Add end bearing of 100-150mm to both ends of span
Category
85 x 7 - 5kg/m
600 700 800 900 1200 1500 1800 2100 2400 2700 3000 3600
A
B
C
D
E
|
Building Products

Angle Bar * Follow the colour code from the loading categories above. Add end bearing of 100-150mm to both ends of span
Category
100 x 100 - 9kg/m
600 700 800 900 1200 1500 1800 2100 2400 2700 3000 3600
A
B
C
D
E

Angle Bar * Follow the colour code from the loading categories above. Add end bearing of 100-150mm to both ends of span
Category
150 x 100 - 12kg/m
600 700 800 900 1200 1500 1800 2100 2400 2700 3000 3600
A
B
C
D
Steel Centre
88
KNOW YOUR STEEL
Safe Load Tables
Flat Bar Clear Span Length (mm)

85 x 7 - 5kg/m any structural product for a construction application. UDL = Uniform Distributed Load
Span (mm) 600 700 800 900 1000

Bar Length (mm) 800 900 1000 1100 1200
Total Load (kg) 43.7 32.1 24.5 19.4 15.7
UDL (kg/m) 72.8 45.9 30.6 21.6 15.7
Total Load (kg) 72.8 53.4 40.9 32.3 26.2
UDL (kg/m) 121.3 76.3 51.1 35.9 26.2
Angle Bar Clear Span Length (mm)

Building Products
Span (mm) 1000 1200 1500 1800 2100 2400 2700 3000
Bar Length (mm) 1200 1500 1800 2100 2400 2700 3000* 3300*
Total Load (kg) 2083 1736 1265 878 645 486 384 311
UDL (kg/m) 2083 1447 843 488 307 203 142 104
Total Load (kg) 2083 1736 1389 1157 992 811 641 519
UDL (kg/m) 2083 1447 926 643 472 338 237 173
|
Angle Bar Clear Span Length (mm)
Span (mm) 1500 1800 2100 2400 2700 3000 3600

Bar Length (mm) 1800 2100 2400 2700 3000 3300 4000
Total Load (kg) 3024 2520 1993 1526 1206 976 676
UDL (kg/m) 2016 1400 949 636 447 325 188
Total Load (kg) 3024 2520 2100 1890 1680 1512 1312
UDL (kg/m) 2016 1400 1000 788 622 504 364
• Loads not limited by • Loads limited by short term deflection of 1/600 span
deflection
• Loads limited by short term deflection of 1/360 span
Steel Centre
89
KNOW YOUR STEEL
C-Purlins
Size Mass
Designation
mm x mm x mm kg/m
C 10010 102 x 51 x 1.0 1.78
C 10012 102 x 51 x 1.2 2.10
C 10015 102 x 51 x 1.5 2.62
C 10019 102 x 51 x 1.9 3.29
C 15012 152 x 64 x 1.2 2.89
C 15015 152 x 64 x 1.5 3.59
C 15019 152 x 64 x 1.9 4.51
C 15024 152 x 76 x 2.4 5.70
C 20015 203 x 76 x 1.5 4.49
C 20019 203 x 76 x 1.9 5.74
C 20024 203 x 76 x 2.4 7.24
Battens Roofing and Walling
C 25019 254 x 76 x 1.9 6.50 Note: Purlins are made from

high tensile steel to be fastened
C 25024 254 x 76 x 2.4 8.16 rather than welded. Purlins can
C 30024 300 x 96 x 2.4 10.1 be ordered pre-cut to length and
with pre-punched holes or slots.
Purlins
C 30030 300 x 96 x 3.0 12.6

C 35030 350 x 125 x 3.0 15.1
|
Building Products
Z-Purlins
|
Building Products
Web Thickness Flange Flange Flange Mass

Designation
D (mm) t (mm) E (mm) F (mm) L (mm) kg/m
Z 10010 102 1.0 53 49 12.5 1.78
Z 10012 102 1.2 53 49 12.5 2.10
Z 10015 102 1.5 53 49 13.5 2.62
Z 10019 102 1.9 53 49 14.5 3.29
Z 15012 152 1.2 66 61 15.5 2.89
Z 15015 152 1.5 66 61 16.5 3.59
Z 15019 152 1.9 66 61 17.5 4.51
Z 15024 152 2.4 70 60 19.5 5.70
Z 20015 203 1.5 77 74 15.0 4.49
Z 20019 203 1.9 80 74 18.5 5.74
Z 20024 203 2.4 82 73 21.5 7.24
Z 25019 254 2.4 79 74 18.0 6.50
Z 25024 254 2.4 79 73 21.0 8.16
Z 30024 300 2.4 105 93 27.0 10.1
Z 30030 300 3.0 107 93 31.0 12.6
Z 35030 350 3.0 134 121 30.0 15.1
Steel Centre
Note: Purlins are made from high

tensile steel to be fastened rather than
welded. Purlins can be ordered pre-cut
to length and with pre-punched holes
or slots.
90
KNOW YOUR STEEL
Battens, Roofing and Walling
LYSAGHT TOPSPAN®
LYSAGHT TOPSPAN® has been used in the building and construction

industry for many decades in commercial and residential applications.
Applications include sheds, garages, carports, and as ceiling and roof
battens as well as for handyman projects
TOPSPAN® 22
BMT MASS Yield Strength Coating Mass

mm kg/m Mpa g/m2
0.42 0.35 550 150
Description
22mm deep batten ideal for use as a ceiling batten for internal fixing of
ceiling or wall liner. MPa minimum yield stress, 150g/m2 minimum coating
mass).
Building Products
TOPSPAN® 40
NSW, ACT, QLD, SA, VIC ONLY BMT MASS Yield Strength Coating Mass
WA & NT mm kg/m Mpa g/m2
42mm 0.48* (VIC
0.60 550 150
ONLY)
|
0.55 0.67 550 150
41mm 0.75 0.91 550 150
Description
15mm
Ideal for use as a roofing batten for residential steel or tiled roof,
90mm
TOPSPAN® 40 is a 40mm deep batten offering a high strength yet light
weight solution that won’t shrink, warp or twist.
TOPSPAN® 61
BMT MASS Yield Strength Coating Mass

mm kg/m Mpa g/m2
0.60 0.95 550 125
0.75 1.18 550 125
1.00 1.56 550 125
1.20 1.87 550 125
Description
TOPSPAN® 61 is 61mm deep batten ideal for small framed

shed and awning applications with a convenient size between that
of a small purlin and large batten.
Steel Centre
91
KNOW YOUR STEEL
Battens, Roofing and Walling
TOPSPAN® 96* (QLD ONLY)
31.7mm BMT MASS Yield Strength Coating Mass

mm kg/m Mpa g/m2
0.75 1.68 550 125
1.00 2.22 550 125
1.20 2.66 550 125
96mm
Description
TOPSPAN® 96, available only in Queensland, is a 96mm deep roof purlin or

14mm wall girt ideal for sheds, garages, carports and awnings.
117mm
TOPSPAN® 120
40mm BMT MASS Yield Strength Coating Mass

mm kg/m Mpa g/m2

0.70 2.07 550 125
0.90 2.64 550 125
1.00 2.93 550 125
120mm
Description
A 120mm deep roof purlin or wall girt, TOPSPAN® 120 is commonly

used in rural, residential and small commercial applications for sheds,
26mm garages and awnings where longer spans or strength is required.
149mm
|
Building Products
At InfraBuild Steel Centre our complete one-stop-shop

saves you time and reduces complexity and risk on your
next building project. We take your plans and provide
a full-service solution: take offs, estimation, technical
support, scheduling and delivery for all steel requirements.
Our quality manufactured products give you confidence,
because they meet relevant Australian Standards and
Building Codes. Enquire with us today about how we can
help you deliver your next building project on time and on
budget.
Steel Centre
92
KNOW YOUR STEEL
Flashings
Ridge Cap
Stock lengths
Description
170 170 mm
30 30
Ridge Capping RC1 1800
2400
162 162
1800
20 20 Ridge Capping RC2
2400
1800
Ridge Roll Top RC3
2400
Note: Stock lengths and custom cut. Available in Zincalume® and Colorbond®. For fasteners refer to page 115.
Barge Mould/Corner Mould
Building Products
Size Stock lengths
mm mm
External
External – 75 x 75 1800 & 2400
External – 100 x 100 1800 & 2400
Internal – 150 x 100 1800 & 2400
Internal
|
Internal – 150 x 150 1800 & 2400
Flashings
Note: Stock lengths and custom cut. Available in Zincalume® and Colorbond®. For fasteners refer to page 115.
Barge Capping/Parapet
Stock lengths
Description Profile
mm
156
31 75 182 Barge Capping Spandek Hi-Ten 1800 & 2400
100 31 Custom Orb 1800 & 2400
Trimdek Hi-Ten 1800 & 2400
170 Parapet Flashing Spandek Hi-Ten 1800 & 2400
30 90 145
90 Custom Orb 1800 & 2400
15
Trimdek Hi-Ten 1800 & 2400
Barge Capping Parapet Flashing Note: Stock lengths and custom cut. Available in Zincalume® and Colorbond®.
For fasteners refer to page 115.
Steel Centre
93
KNOW YOUR STEEL
COLORBOND® Steel Colour Range
Standard Colour Range
Classic
Basalt® Cottage Green® CoveTM Deep Ocean® Dune® Evening Haze®
Cream™
GullyTM Ironstone® Jasper® Mangrove® Manor Red® Monument® Night Sky®

Building Products | COLORBOND® Steel Colour Range
Pale Woodland
Paperbark® Shale Grey™ Surfmist® Terrain® Wallaby® Windspray®
Eucalypt® Grey®
Matt Colour Range
Basalt® Dune® Monument® Shale Grey ™ Surfmist®
The printed steel colours shown here have been reproduced to represent actual colours as
accurately as possible. However we recommend checking your chosen colour against an
actual product sample before purchasing as varying light conditions and print limitations
affect colour tones.
Steel Centre
94
KNOW YOUR STEEL
Rainwater Products
Dimensions
Product Image Description
mm
Stramit® Quad Gutter Various sizes
Stramit® Half Round Gutter Various sizes
Stramit® M Pattern Gutter 85 x 123 x 140 front (QLD, NSW only)
Building Products
Stramit® Fascia Gutter 25 x 90 x 127, 140 front (VIC, TAS only)
Stramit® Downpipe Rectangular 100 x 50, 100 x 75, 100 x 100, 100 x 150
|
Rainwater Products
Stramit® Downpipe Round Diameter: 50, 65, 75, 90, 100
Stramit® Flashings Various sizes
Note: For fasteners refer to page 115.

®
Registered trademark of Stramit Corporation Pty Limited trading as Stramit Building Products ABN 57 005 010 195. A Member of the Fletcher Building Group.
COLORBOND® and ™ are trade marks of BlueScope Steel Limited.
Steel Centre
95
KNOW YOUR STEEL
Structural Products
Dimensions
Product Image Description
mm
27.5 30
0.75 & 1.00 BMT, 300mm Cover
54 55 Stramit Condeck HP®
55mm Rib Height
300
25
15
slab
thickness
Stramit® Edgeforma Various sizes
75
27mm
Stramit PrimeForm™ 0.60 & 0.75 BMT (VIC only)
500mm
600mm
Structural Products
Stramit® C & Z Purlins Various sizes
64 x 34 x 20 x 6, 96 x 34 x 20 x 6,
B Stramit® Top Hats
D 120 x 42 x 27 x 10 (A x B x C x D)
A
C
|
Building Products
Bearer
Joist
Stramit® Flooring Various sizes
Screw
(self-tapping)
Stramit® Roof Batten 40 x 40 x 15 x 6.0m & 7.5m

40
Stramit® Ceiling Batten Length 6.1m
40
Brackets & Angle Connectors Various sizes
®
Registered trademark of Stramit Corporation Pty Limited trading as Stramit Building Products ABN 57 005 010 195. A Member of the Fletcher Building Group.
COLORBOND® and ™ are trade marks of BlueScope Steel Limited.
Steel Centre
96
KNOW YOUR STEEL
Roofing and Walling
BMT Width of
Description Application Base Metal Thickness Coverage
mm mm
Longline 305 Roofing 0.7 305
Multiclad Walling 0.42 840
Easyclad Walling 0.42 300
Gutters and Fascia
Dimensions (mm)
Building Products | Gutters, Fascia and Decking

Product Availability
A B C
Quad 115 Hi Front QLD, SA, NSW, VIC, TAS 62 90 115
Trimline QLD, Nth NSW, VIC, TAS 72 116 124
Sheerline except QLD 81 141 124
Emline QLD 89 125 140
Half Round except NT 150
Ranceline WA 70 90 98
Colonial WA 63 90 90
Novaline QLD, SA, NSW, VIC, TAS, WA 18 185 35
Structural Decking
BMT Width of
Mass
Description Base Metal Thickness Coverage
kg/m2
mm mm
Bondek Plus 0.6 8.52 600

Steel Centre
Bondek Plus 0.75 10.5 600
Bondek Plus 1 13.79 600
97
KNOW YOUR STEEL
Fencing
Neetascreen Smartascreen Miniscreen Customscreen
Infill Sheet
Dimension Qty Dimension Qty Dimension Qty Dimension Qty
Height mm 3 Height mm 3 Height mm 3 Height mm 3
1190 (non std) 1190 (non std) 1190 (non std) 1190 (non std)
1490 1490 1490 1490
1790 1790 1790 1790
2090 2090 2090 2090
Non-standard Non-standard Non-standard Non-standard
Post
Height mm 2 Height mm 2 Height mm 2 Height mm 2
2100 2100 2100 2100
2400 2400 2400 2400
2700 2700 2700 2700
3000 3000 3000 3000
Rails
Universal Rail 2 Universal Rail 2 Miniscreen Rail 2 Customscreen Rail 2
Length mm Length mm Length mm Length mm
Fencing
2350 2350 2350 2370

3100 3100 3100 3100
(raked panels only) (raked panels only) (raked panels only) (raked panels only)
Miniscreen Centre Rail

|

Building Products
Length mm
2350
3100
(raked panels only)
Fasteners
Metal Teks Hex Metal Teks Hex Metal Teks Hex Metal Teks Hex
Head 10-16 x 16 17 Head 10-16 x 16 17 Head 10-16 x 16 17 Head 10-16 x 16 17
(no neo) (no neo) (no neo) (no neo)
Ripple Teks
Note: Miniscreen not available in SA. 7
10 x 16-20
Customscreen available in QLD and
SA only. Post Cap
1 1 1 1
Standard Fencing Colour Range
Basalt® Bluegum® Domain® Dune® Evening Haze® Ironstone® Monument®

Steel Centre
Pale Woodland
Paperbark® Riversand® Shale Grey™ Surfmist® Wilderness® Wollemi®
Eucalypt® Grey®
98
Piping Systems
KNOW YOUR STEEL

Steel Pipes to American Standards
Outside Nominal Wall Thicknesses & Weights for KEY: Dimensions - mm (Black)
Nominal Size
Diameter Welded & Seamless Steel Pipe ASME B36.10 Weight - kg/m (Green)
Extra XX Sched. Sched. Sched. Sched. Sched. Sched. Sched. Sched. Sched. Sched.
Dn Nps Mm Std
Strong Strong 10 20 30 40 60 80 100 120 140 160
1.73 2.41 1/3 2.41

6 1/8 10.3 – – – – – – – – –
0.37 0.47 0.37 0.47
2.24 3.02 2.24 3.02
8 1/4 13.7 – – – – – – – – –
0.63 0.80 0.63 0.80
2.31 3.2 2.31 3.2
10 3/8 17.1 – – – – – – – – –
0.84 1.10 0.84 1.10
2.77 3.73 7.47 2.77 3.73 4.78
15 1/2 21.3 – – – – – – –
1.27 1.62 2.55 1.27 1.62 1.95
2.87 3.91 7.82 2.87 3.91 5.56
20 3/4 26.7 – – – – – – –
1.69 2.20 3.64 1.69 2.20 2.90
3.38 4.55 9.09 3.38 4.55 6.35
25 1 33.4 – – – – – – –
2.50 3.24 5.45 2.50 3.24 4.24
3.56 4.85 9.7 3.56 4.85 6.35
32 1-1/4 42.2 – – – – – – –
3.39 4.47 7.77 3.39 4.47 5.61
3.68 5.08 10.15 3.68 5.08 7.14
40 1-1/2 48.3 – – – – – – –
4.05 5.41 9.56 4.05 5.41 7.25
3.91 5.54 11.07 3.91 5.54 8.74
50 2 60.3 – – – – – – –
5.44 7.48 13.44 5.44 7.48 11.11
5.16 7.01 14.02 5.16 7.01 9.53
65 2 - 1/2 73.0 – – – – – – –
8.63 11.41 20.39 8.63 11.41 14.92
5.49 7.62 15.24 5.49 7.62 11.13
Piping Systems
80 3 88.9 – – – – – – –
11.29 15.27 27.67 11.29 15.27 21.35
5.74 8.08 5.74 8.08
90 3 - 1/2 101.6 – – – – – – – – –
13.57 18.63 13.57 18.63
6.02 8.56 17.12 6.02 8.56 11.13 13.49
100 4 114.3 – – – – – –
16.07 22.32 41.03 16.07 22.32 28.32 33.54
6.55 9.53 19.05 6.55 9.53 12.7 15.88
125 5 141.3 – – – – – –
21.77 30.91 57.43 21.77 30.97 40.28 49.11
7.11 10.97 21.95 7.11 10.97 14.27 18.26
150 6 168.3 – – – – – –
|
28.26 42.56 79.22 28.26 42.56 54.20 67.56
Steel Pipes to American Standards

8.18 12.7 22.23 6.35 7.04 8.18 10.31 12.7 15.09 18.26 20.62 23.01
200 8 219.1 –
45.55 64.64 107.92 33.31 36.81 42.55 53.08 64.65 75.92 90.44 100.92 111.27
9.27 12.7 25.4 6.35 7.8 9.27 XS 15.09 18.26 21.44 XXS 28.58
250 10 273.1 –
60.31 81.55 155.15 41.77 51.03 60.31 81.55 96.01 114.75 133.06 155.15 172.33
9.53 12.7 25.4 6.35 8.38 10.31 14.27 17.48 21.44 XXS 28.58 33.32
300 12 323.9 –
73.88 186.97 186.97 49.73 65.20 79.73 108.96 132.08 159.91 186.97 208.14 238.76
9.53 12.7 6.35 7.92 Std. W.T. 11.13 15.09 19.05 23.83 27.79 31.75 35.71
350 14 355.6 –
93.27 107.10 54.99 67.90 81.33 94.55 126.70 158.10 194.96 224.65 253.56 281.70
9.53 12.7 6.35 7.92 Std. W.T. XS 16.66 21.44 26.19 30.96 36.53 40.49
400 16 406.4 –
93.27 123.30 62.64 77.83 93.27 123.50 160.12 203.53 245.56 286.64 333.19 365.35
9.53 12.7 6.35 7.92 11.13 14.27 19.05 23.83 29.36 34.93 39.67 45.24
450 18 457 –
105.16 139.15 70.57 87.71 122.38 155.80 205.74 254.55 309.62 363.56 408.26 365.35
9.53 12.7 6.35 Std. W.T. XS 15.09 20.62 26.19 32.54 38.1 44.45 50.01
500 20 508 –
117.15 155.12 78.55 117.15 155.12 183.42 247.83 311.17 381.53 441.49 508.11 564.81
9.53 12.7 6.35 Std. W.T. SX 22.23 28.58 34.93 41.28 47.63 53.98
550 22 559 – –
129.13 171.09 86.54 129.13 171.09 294.25 373.83 451.42 527.05 600.63 672.26
9.53 12.7 6.35 Std W.T. 14.27 17.48 24.61 30.96 38.89 46.02 52.37 59.54
600 24 610 –
141.12 187.06 94.53 141.12 209.64 255.41 355.26 442.08 547.71 640.03 720.15 808.22
9.53 12.7 7.92 XS
650 26 660 – – – – – – – – –
152.87 202.72 127.36 202.72
9.53 12.7 7.92 XS 15.88
700 28 711 – – – – – – – –
164.85 218.69 137.31 218.69 271.21
9.53 12.7 7.92 XS 15.88
750 30 762 – – – – – – – –
176.84 234.67 147.28 234.67 292.18
9.53 12.7 7.92 XS 15.88 17.48
800 32 813 – – – – – – –
188.82 250.64 157.24 250.64 312.15 342.91
9.53 12.7 7.92 XS 15.88 17.48
850 34 864 – – – – – – –
200.31 266.61 167.20 266.61 332.12 364.90
9.53 12.7 7.92 XS 15.88 19.05
900 36 914 – – – – – – –
212.56 282.27 176.96 282.27 351.7 420.42
9.53 12.7
1050 42 1067 – – – – – – – – – – –
248.52 330.19
Formula to attain approximate mass in kilograms per metre (kg/m) for Steel Round Pipe and Tubing
Steel Centre
m = (D – t) t x 0.02466 Where: m = mass to the nearest 0.01 kg/m Example

D = Outside Diameter in millimetres nominal Size Step 1. 323.9 – 9.53 = 314.37
(to nearest 0.1mm for OD up to 406.4mm) Dn300 nPS12 Step 2. 314.37 x 9.53 = 2995.9461
(to nearest 1.0mm for OD 457mm and above) OD = 323.9mm Step 3. 2995.9461 x 0.024 66
= Wall thickness to nearest 0.01mm W.t. = 9.53mm = 73.88kg/m
99
KNOW YOUR STEEL
Stainless Steel Pipes

to American Standards
Nominal Wall Thickness & Inside Diameter (mm) for Stainless Steel Pipe ASME B36.19
Nominal Outside
Schedule 55 Schedule 105 Schedule 405 Schedule 805
Size Diameter
(DN) mm Wall Inside Wall Inside Wall Inside Wall Inside
Thickness Diameter Thickness Diameter Thickness Diameter Thickness Diameter
6 10.29 – – 1.24 7.81 1.73 6.83 2.41 5.47
8 13.72 – – 1.65 10.42 2.24 9.24 3.02 7.68
10 17.15 – – 1.65 13.85 2.31 12.53 3.2 10.75
15 21.34 1.65 18.04 2.11 17.12 2.77 15.8 3.73 13.88
20 26.67 1.65 23.37 2.11 22.45 2.87 20.93 3.91 18.85
25 33.4 1.65 30.1 2.77 27.86 3.38 26.64 4.55 24.3
32 42.16 1.65 38.86 2.77 36.62 3.56 35.04 4.85 32.46
40 48.26 1.65 44.96 2.77 42.72 3.68 40.9 5.08 38.1
50 60.33 1.65 57.03 2.77 54.79 3.91 52.51 5.54 49.25
65 73.03 2.11 68.81 3.05 66.93 5.16 62.71 7.01 59.01
80 88.9 2.11 84.68 3.05 82.8 5.49 77.92 7.62 73.66
100 114.3 2.11 110.08 3.05 108.2 6.02 102.26 8.56 97.18
125 141.3 2.77 135.76 3.4 134.5 6.55 128.19 9.52 122.25
Stainless Steel Pipes to American Standards
150 168.28 2.77 162.74 3.4 161.47 7.11 154.05 10.97 146.33
200 219.08 2.77 213.54 3.76 211.56 8.18 202.72 12.7 193.68
250 273.05 3.4 266.24 4.19 264.67 9.27 254.51 12.70* 247.65
300 323.85 3.96 315.93 4.57 314.71 9.52 304.08 12.70* 298.45
350 355.6 3.96 347.68 4.78 346.05 – – – –
400 406.4 4.19 398.02 4.78 396.85 – – – –
450 457.2 4.19 448.82 4.78 447.65 – – – –
500 508 4.78 498.45 5.54 496.93 – – – –
600 609.6 5.54 598.53 6.35 596.9 – – – –
750 762 6.35 749.3 7.92 746.16 – – – –
|
Piping Systems
Innovative Mechanical Pipe Joining Solutions

Victaulic® manufacturers a range of innovative pipe joining and
flow control solutions with benefits including:
• Safer and faster installation
• Lower total installed cost
• Significantly reduced downtime
• Reduced operational costs
• Versatility of design
• Reusable parts help to expedite maintenance
Speak to the team at InfraBuild Steel Centre about a Victaulic®
solution to suit your application.
Steel Centre
100
KNOW YOUR STEEL
Carbon Steel Buttweld Fittings
Wall Thickness (mm) for Buttweld Fittings to ASME B16.19, B16.28 and BS.1640 E.
Nom. Pipe Std. Nom.
Size OD Sch. Sch. Sch. Std. Sch. Sch. Sch. Sch. Sch. Sch. Sch. X.X. A B K D V Wt. Size
Dn mm X Stg & Ex DN
10 20 30 Wt. 40 60 80 100 120 140 160 Stg
Stg
15 21.3 – – – 2.77 – 3.73 – – – 4.78 7.47 38 16 47.5 – – 25.4 15
20 26.7 – – – 2.87 – 3.91 – – – 5.56 7.82 38 19 43 19 33 25.4 20
25 33.4 – – – 3.38 – 4.55 – – – 6.35 9.09 38 22 55.5 25.4 41 38.1 25
32 42.2 – – – 3.56 – 4.85 – – – 6.35 9.7 47.5 25.4 70 32 52 38.1 32
40 48.3 – – – 3.68 – 5.08 – – – 7.14 10.15 57 29 82.5 38 62 38.1 40
50 60.3 – – – 3.91 – 5.54 – – – 8.74 11.07 76 35 106 51 81 38.1 50
65 73 – – – 5.16 – 7.01 – – – 9.53 14.02 95 44.5 132 63.5 100 38.1 65
80 88.9 – – – 5.49 – 7.62 – – – 11.13 15.24 114 51 159 76 121 50.8 80
90 101.6 – – – 5.74 – 8.08 – – – 16.15 133 57 184 89 140 63.5 90
100 114.3 – – – 6.02 – 8.56 – 11.13 – 13.49 17.12 152 63.5 210 102 159 63.5 100
125 141.3 – – – 6.55 – 9.53 – 12.7 – 15.88 19.05 190 79 262 127 197 76.2 125
150 168.3 – – – 7.11 – 10.97 – 14.27 – 18.26 21.95 229 95 313 152 237 88.9 150
200 219.1 – 6.35 7.04 8.18 10.31 12.7 15.09 18.26 20.62 23.01 22.23 305 127 414 203 313 102 200
250 273.1 – 6.35 7.8 9.27 12.7 12.7 15.09 18.26 21.44 25.4 28.58 25.4 381 159 517 254 390 127 250
300 323.9 – 6.35 8.38 9.53 10.31 14.27 12.7 17.48 21.44 25.4 28.58 33.32 25.4 457 190 619 305 467 152 300
350 355.6 6.35 7.92 9.53 9.53 11.13 15.09 12.7 19.05 23.83 27.79 31.75 35.71 – 533 222 711 356 533 165 350
400 406.4 6.35 7.92 9.53 9.53 12.7 16.66 12.7 21.44 26.19 30.96 36.53 40.49 – 610 254 813 406 610 178 400
450 457 6.35 7.92 11.13 9.53 14.27 19.05 12.7 23.83 29.36 34.93 39.67 45.24 – 686 286 914 457 686 203 450
500 508 6.35 9.53 12.7 9.53 15.09 20.62 12.7 26.19 32.54 38.1 44.45 50.01 – 762 318 1016 508 762 229 500
600 610 6.35 9.53 14.27 9.53 17.48 24.61 12.7 30.96 38.89 46.02 52.37 59.54 914 381 1219 610 914 267 600
750 762 7.92 12.7 15.88 9.53 – – 12.7 – – – – – 1143 470 1524 762 1143 267 750
900 914 7.92 12.7 15.88 9.53 19.05 – 12.7 – – – – – 1372 565 – 914 1372 267 900
Piping Systems
B16.9 B16.28
Long radius welding elbows, return bends & caps Radius welding elbows, return bends
B
K V
A E D
B
D D D
A A
|
A
90° 45° 180° 90° 180°
Carbon Steel Buttweld Fittings

Nominal Size Nominal Size Nominal Size
DN C M H DN C M H DN C M H
Straight tees (b16.9) Large Small Large Small Large Small
End End End End End End
20 20 28.6 – – 100 100 105 – – 400 400 305 – –
15 28.6 28.6 38.1 90 105 102 102 350 305 305 356
C
25 25 38.1 – – 80 105 98.4 102 300 305 295 356
20 38.1 38.1 50.8 65 105 95.3 102 250 305 283 356
C C 15 38.1 38.1 50.8 50 105 88.9 102 200 305 273 356
32 32 47.6 – – 40 105 85.7 102 150 305 264 356
25 47.6 47.6 50.8 125 125 124 – – 450 450 343 – –
20 47.6 47.6 50.8 100 124 117 127 400 343 330 381
15 47.6 47.6 50.8 90 124 114 127 350 343 330 381
40 40 57.2 – – 80 124 111 127 300 343 321 381
32 57.2 57.2 63.5 65 124 108 127 250 343 308 381
Reducing tees (b16.9) 25 57.2 57.2 63.5 50 124 105 127 200 343 298 381
20 57.2 57.2 63.5 150 150 143 – – 500 500 381 – –
15 57.2 57.2 63.5 125 143 137 140 450 381 368 508
M 50 50 63.5 – – 100 143 130 140 400 381 356 508
40 63.5 60.3 76.2 90 143 127 140 350 381 356 508
32 63.5 57.2 76.2 80 143 124 140 300 381 346 508
C C 25 63.5 50.8 76.2 65 143 121 140 250 381 333 508
20 63.5 44.5 76.2 200 200 178 – – 200 381 324 508
65 65 76.2 – – 150 178 168 152 600 600 432 – –
50 76.2 69.9 88.9 125 178 162 152 500 432 432 508
40 76.2 66.7 88.9 100 178 155 152 450 432 419 508
32 76.2 63.5 88.9 80 178 152 152 400 432 406 508
25 76.2 57.2 88.9 250 250 216 – – 350 432 406 508
Concentric & eccentric 80 80 85.7 – – 200 216 203 178 300 432 397 508
Reducers (b16.9) 65 85.7 82.6 88.9 150 216 194 178 250 432 384 508
50 85.7 76.2 88.9 125 216 191 178 750 750 559 – –
40 85.7 73.0 88.9 100 216 184 178 600 559 533 610
32 85.7 69.9 88.9 300 300 254 – – 500 559 508 610
H H 25 85.7 69.9 88.9 250 254 241 203 450 559 495 610
90 90 95.3 – – 200 254 229 203 400 559 483 610
80 95.3 92.1 102 150 254 219 203 900 900 673 – –
Steel Centre
65 95.3 88.9 102 100 254 210 203 750 673 635 610
50 95.3 82.6 102 350 350 279 – – 600 673 610 610
40 95.3 79.4 102 300 279 270 330 500 673 584 610
250 279 257 330 450 673 572 610
200 279 248 330
150 279 238 330
101
KNOW YOUR STEEL
Flanges to American Standards

DN 15 to 600 are to ASME B16.5 (BS1560). DN 750 & 900 are to BS 3293 for Slip-On & Weldneck only.
Blind Flanges up to DN600

Welding Neck Flange Threaded Flange Slip-On Flange Socket Welding (DN) 15-80 (Above DN600 see notes below †)
PN20 (Class 150) PN50 (Class 300) PN100 (Class 600)

Length Thru Length Thru Length Thru
Nom. Thick- Hub Thick- Hub Thick- Hub Nom.
Size ness Thrd. Dia of Dia of ness Thrd. Dia of Dia of ness Thrd. Dia of Dia of Size
Dia of No. of Dia of No. of Dia of No. of
Dn of Fig. Slip- On Weld Bolt Bolt of Fig. Slip- On Weld Bolt Bolt of Fig. Slip- On Weld Bolt Bolt DN
Fig. 0 Bolts Fig. 0 Bolts Fig. 0 Bolts
Min. Soc/ Neck Circle Holes Min. Soc/ Neck Circle Holes Min. Soc/ Neck Circle Holes
C(1)* Weld Y(1)* C(2)* Weld Y(2)* C(1)* Weld Y(1)*
Y(1)* Y(2)* Y(1)*
15 90 11.5 16 48 60.5 16 4 95 14.5 22 52 66.5 16 4 95 14.5 22 52 66.5 16 4 15
20 100 13 16 52 70 16 4 120 16 25 57 82.5 20 4 120 16 25 57 82.5 20 4 20
25 110 14.5 17 56 79.5 16 4 125 17.5 27 62 89 20 4 125 17.5 27 62 89 20 4 25
32 120 16 21 57 89 16 4 135 19.5 27 65 98.5 20 4 135 21 29 67 98.5 20 4 32
40 130 17.5 22 62 98.5 16 4 155 21 30 68 114.5 22 4 155 22.5 32 70 114.5 22 4 40
50 150 19.5 25 64 120.5 20 4 165 22.5 33 70 127 20 8 165 26.5 37 73 127 20 8 50
65 180 22.5 29 70 139.5 20 4 190 25.5 38 76 149 22 8 190 29 41 79 149 22 8 65
80 190 24 30 70 152.5 20 4 210 29 43 79 168.5 22 8 210 32 46 83 168.5 22 8 80
90 215 24 32 71 178 20 8 230 30.5 44 81 184 22 8 230 35 49 86 184 26 8 90
100 230 24 33 76 190.5 20 8 255 32 48 86 200 22 8 275 38.5 54 102 216 26 8 100
125 255 24 36 89 216 22 8 280 35 51 98 235 22 8 330 44.5 60 114 267 30 8 125
150 280 25.5 40 89 241.5 22 8 320 37 52 98 270 22 12 355 48 67 117 292 30 12 150
200 345 29 44 102 298.5 22 8 380 41.5 62 111 330 26 12 420 55.5 76 133 349 33 12 200
250 405 30.5 49 102 362 26 12 445 48 67 117 387.5 30 16 510 63.5 86 152 432 36 16 250
300 485 32 56 114 432 26 12 520 51 73 130 451 33 16 560 66.5 92 156 489 36 20 300
350 535 35 57 127 476 30 12 585 54 76 143 514.5 33 20 605 70 94 165 527 39 20 350
400 600 37 64 127 540 30 16 650 57.5 83 146 571.5 36 20 685 76.5 106 178 603 42 20 400
450 635 40 68 140 578 33 16 710 60.5 89 159 628.5 36 24 745 83 117 184 654 45 20 450
500 700 43 73 145 635 33 20 775 63.5 95 162 686 36 24 815 89 127 190 724 45 24 500
600 815 48 83 152 749.5 36 20 915 70 106 168 813 42 24 940 102 140 203 838 52 24 600
750 985 54 89 130.2 914 35 28 1090 92 210 210 997 48 28 1130 114 248 248 1022 54 28 750
900 1170 60.3 95 136.5 1086 41 32 1270 105 241 241 1168 54 32 1315 124 283 283 1194 67 28 900
PN150 (Class 900) PN250 (Class 1500) PN420 (Class 2500)

Length Thru Length Thru Length Thru
Hub Hub Hub
Nom. Thick- Thick- Thick- Nom.
Thrd.
Size ness Thrd. Dia of Dia of ness Thrd. Dia of Dia of ness Dia of Dia of Size
Dia of No. of Dia of No. of Dia of Slip- No. of
Dn of Fig. Slip- On Weld Bolt Bolt of Fig. Slip- On Weld Bolt Bolt of Fig. Weld Bolt Bolt DN
Fig. 0 Bolts Fig. 0 Bolts Fig. 0 On Bolts
Min. Soc/ Neck Circle Holes Min. Soc/ Neck Circle Holes Min. Neck Circle Holes
Soc/
C(2)† Weld Y(2)* C(2)† Weld Y(2)† C(2)† Y(2)†
Weld
Y(2)† Y(2)†
Y(2)†
15 120 22.5 32 60 82.5 22 4 135 30.5 40 73 89 22 4 15
20 130 25.5 35 70 89 22 4 140 32 43 79 95 22 4 20
25 150 29 41 73 101.5 26 4 160 35 48 89 108 26 4 25
32 Use PN250 Dimensions in these Sizes 160 29 41 73 111 26 4 185 38.5 52 95 130 30 4 32
40 180 32 44 83 124 30 4 205 44.5 60 111 146 33 4 40
50 215 38.5 57 102 165 26 8 235 51 70 127 171.5 30 8 50
65 245 41.5 64 105 190.5 30 8 270 57.5 79 143 197 33 8 65
|
80 240 38.5 54 102 190.50 26 8 270 48 73 118 203 33 8 305 67 92 168 228.5 36 8 80
100 295 44.5 70 114 235.00 32 8 310 54 90 124 241.5 36 8 355 76.5 108 190 273 42 8 100
Piping Systems
125 350 51 79 127 279.50 35 8 375 73.5 105 155 292 42 8 420 92.5 130 229 324 48 8 125
150 380 56 86 140 317.50 32 12 395 83 119 171 317.5 39 12 485 108 152 273 368.5 56 8 150
200 470 63.5 102 162 393.5 39 12 485 92 143 213 393.5 45 12 550 127 178 318 438 56 12 200
250 545 70 108 184 470 39 16 585 108 159 254 482.5 52 12 675 165.5 229 419 539.5 68 12 250
300 610 79.5 117 200 533.5 39 20 675 124 181 283 571.5 56 16 760 184.5 254 464 619 76 12 300
350 640 86 130 213 559 42 20 750 133.5 298 635 60 16 350
400 705 89 133 216 616 45 20 825 146.5 311 705 68 16 400
450 785 102 152 229 686 52 20 915 162 327 774.5 76 16 450
500 855 108 159 248 749.5 54 20 985 178 356 832 80 16 500
600 1040 140 203 292 901.5 68 20 1170 203.5 406 990.5 94 16 600
Notes: Raised Face O.D. Approximate Welding Neck Flange Bores – mm

Diam. Nom.
of
* 1. The 2mm Raised Face is included in Size
Pipe
thickness C(1) and length through hub All Press DN Sch. Sch. Sch. Std. Sch. Sch. Ext. Sch. Sch. Sch. Sch. Sch. X.X
Ratings mm Mm 10 20 30 Wt. 40 60 Stg. 80 100 120 140 160 Stg.
Y(1). This applies to PN20 and PN50
Pressure Ratings. 35 15 21.3 15.8 13.9 11.8 6.4
43 20 26.7 20.9 18.9 15.5 11
† 2. The 7mm Raised Face is not included in
51 25 33.4 26.6 24.3 20.7 15.2
thickness C(2) and length through hub
65 32 42.2 35.1 32.5 29.5 22.8
Y(2). PN100, 150, 250 and 420 Pressure
Same as EXT. STG.
73 40 48.3 40.9 38.1 34 27.9

Same as STD. WT.
Ratings are regularly furnished with 92 50 60.3 52.5 49.2 42.9 38.2
7mm . Raised Face which is additional 105 65 73 62.7 59 54 45
to the flange thickness C(2) and Y(2). 127 80 88.9 77.9 73.7 66.7 58.4
3. Always specify bore when ordering 140 90 101.6 90.1 85.4 – –
weldneck flanges. Bore dimensions 157 100 114.3 102.3 97.2 92.1 87.3 80.1
shown opposite also provide inside 186 125 141.3 128.2 122.3 115.9 109.6 103.2
pipe diameters. 216 150 168.3 154.1 146.3 139.7 131.8 124.4
270 200 219.1 206.4 205 202.7 198.5 193.7 188.9 182.6 177.8 173.1 174.6
Large Diameter Flanges Above DN 600 324 250 273.1 260.3 257.5 254.5 247.7 247.7 242.9 236.5 230.2 222.3 215.9 222.3
381 300 323.9 311.1 307.1 304.8 303.2 295.3 298.5 288.9 281 273.1 266.7 257.2 273.1
• For Blind Flanges refer to MSS SP44. 413 350 355.6 342.9 339.8 336.6 336.6 333.3 325.4 330.2 317.5 307.9 300 292.1 284.2
• BS 3293 covers Slip-On and Weldneck 470 400 406.4 393.7 390.6 387.4 387.4 381 373.1 381 363.5 354 344.5 333.3 325.4
but excludes Blind Flanges.
Steel Centre
533 450 457 444.5 441.4 434.9 438.2 428.7 419.1 431.8 409.5 398.5 387.4 377.9 366.7
• MSS SP44 covers Blind and Weldneck 584 500 508 495.3 489 482.6 489 477.8 466.8 482.6 455.6 442.9 431.8 419.1 408
but excludes Slip-On Flanges. 692 600 610 596.9 590.6 581.1 590.6 574.6 560.4 584.2 547.7 531.8 517.6 504.9 490.5
• BS 3293 Weldneck PN20 flange thickness, 857 750 762 746.2 736.6 730.2 743 736.6
C(1), is less than MSS SP44 equivalents. 1022 900 914 898.6 889 882.6 895.4 876.3 889
• API - 605 Dimensions for Large Diameter
Flanges vary considerably from both BS. All dimensions are shown in millimetres - mm
• 3293 and MSS SP44 — Details on request.
102
KNOW YOUR STEEL
Bolting for ANSI Flanges
Bolting L* L
To suit R.F. Flange sizes DN 15 to 600 to ASME- B16.5

(BS. 1560) and DN 750 & 900 to BS. 3293
*Point Height
Stud Bolt With Nuts Machine Bolt With Nut
PN 20 (Class 150) PN 50 (Class 300) PN 100 (Class 600) PN 150 (Class 900) PN 250 (Class 1500) PN 420 (Class 2500)
Nom. L L L L L L Nom.
Flge Dia. Dia. Dia. Dia. Dia. Dia. Flge
No. Stud Mach No. Stud Mach No. Stud No. Stud No. Stud No. Stud
Size Bolts Bolts Bolts Bolts Bolts Bolts Size
Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts
Dn ins. ins. ins. ins. ins. ins. Dn
mm mm mm mm mm mm mm mm
15 4 1/2 60 45 4 1/2 65 55 4 1/2 80 4 3/4 105 4 3/4 125 15
20 4 1/2 65 50 4 5/8 75 60 4 5/8 90 4 3/4 115 4 3/4 125 20
25 4 1/2 65 55 4 5/8 80 65 4 5/8 90 Use PN250 4 7/8 125 4 7/8 140 25
32 4 1/2 70 55 4 5/8 80 65 4 5/8 100 Dimensions 4 7/8 125 4 1 150 32
40 4 1/2 70 60 4 3/4 90 75 4 3/4 105 in these sizes 4 1 140 4 1 1/8 170 40
50 4 5/8 80 65 8 5/8 90 75 8 5/8 105 8 7/8 145 8 1 175 50
65 4 5/8 90 75 8 3/4 100 85 8 3/4 120 8 1 160 8 1 1/8 195 65
80 4 5/8 90 75 8 3/4 110 90 8 3/4 125 8 7/8 145 8 1 1/8 180 8 1 1/4 220 80
Piping Systems
90 8 5/8 90 75 8 3/4 110 95 8 7/8 140 – – – – – – – – – 90
100 8 5/8 90 75 8 3/4 110 95 8 7/8 145 8 1 1/8 170 8 1 1/4 195 8 1 1/2 255 100
125 8 3/4 90 80 8 3/4 120 100 8 1 165 8 1 1/4 190 8 1 1/2 250 8 1 3/4 300 125
150 8 3/4 100 85 12 3/4 125 105 12 1 170 12 1 1/8 195 12 1 3/8 260 8 2 345 150
200 8 3/4 110 90 12 7/8 140 110 12 1 1/8 195 12 1 3/8 220 12 1 5/8 290 12 2 380 200
250 12 7/8 115 95 16 1 155 130 16 1 1/4 215 16 1 3/8 235 12 1 7/8 335 12 2 1/2 485 250
300 12 7/8 120 100 16 1 1/8 170 145 20 1 1/4 220 20 1 3/8 255 16 2 375 12 2 3/4 540 300
|
350 12 1 130 110 20 1 1/8 175 150 20 1 3/8 235 20 1 1/2 275 16 2 1/4 405 350
Bolting for ANSI Flanges

400 16 1 135 115 20 1 1/4 190 160 20 1 1/2 255 20 1 5/8 285 16 2 1/2 445 400
450 16 1 1/8 150 125 24 1 1/4 195 170 20 1 5/8 275 20 1 7/8 325 16 2 3/4 495 450
500 20 1 1/8 160 135 24 1 1/4 205 180 24 1 5/8 290 20 2 345 16 3 540 500
600 20 1 1/4 175 145 24 1 1/2 230 195 24 1 7/8 330 20 2 1/2 435 16 3 1/2 615 600
750 28 1 1/4 190 160 28 1 3/4 290 250 28 2 355 750
PN150, 250 & 420 – Mot Listed in BS 3293
900 32 1 1/2 215 180 32 2 325 280 28 2 1/2 400 900
Raised Face height of 2 mm for PN20 & 50 and 7 mm for PN100, 150, 250 & 420 is included in dimension L (Bolt Length)
Material Specifications Inch / Metric Bolting

interchangeable for ASME
ASTM A193 Grade B7 Standard specification for alloy steel and stainless B16.5 flanges as below
steel bolting materials for high temperature service. For Use

1/2 M14
ASTM A194 Grade 2h Standard specification for carbon and alloy steel 5/8 M16
nuts for bolts for high pressure and high temperature 3/4 M20
service. 7/8 M24
1 M27
ASTM A320 Standard specification for alloy steel bolting
1 1/8 M30
materials for low temperature service. Grade L7
1 1/4 M33
covers alloy steel stud bolts. Grade L4 covers alloy
1 3/8 M36
steel nuts to suit Grade L7 stud bolts.
1 1/2 M39
1 5/8 M42
1 3/4 M45
1 7/8 M48
2 M52
Steel Centre
2 1/4 M56
2 1/2 M64
2 3/4 M72
103
KNOW YOUR STEEL
Buttweld Fittings and Flanges

to ASME Standards
ASME B36.10 Approximate Mass of Popular Sizes

Steel Pipe Dimensions Pipe Butweld Fittings A.S.M.E Flanges
Con. &
Steel 90o L/R Tees PN100 PN150
Identification Ecc. PN20 (150) PN50 (300)
Nom. Pipe Elbows Equal (600) (900)
Outside Inside Red
Pipe
Diam. Diam. SOW/ SOW/
Size
mm mm Sch. SW W/N Blind SW W/N Blind W/N W/N
DN Std. X.S kg/m kg/ea kg/ea kg/ea
No. Thrded kg/ea kg/ea Thrded kg/ea kg/ea kg/ea kg/ea
kg/ea kg/ea
15 21.3 15.8 Std. 40 1.27 0.08 0.16 – 0.45 0.79 0.57 0.73 0.91 0.79 0.91 2
13.9 XS 80 1.62 1.62 0.21 –
20 26.7 20.9 Std. 40 1.69 0.08 0.21 0.07 0.68 0.86 0.91 1.25 1.41 1.13 1.59 2.72
18.9 XS 80 2.20 0.11 0.27 0.10
25 33.4 26.6 Std. 40 2.50 0.17 0.34 0.14 0.95 1.09 1.09 1.36 1.81 1.77 1.86 3.86
24.3 XS 80 3.24 0.21 0.43 0.18
32 42.2 35.1 Std. 40 3.39 0.28 0.64 0.18 1.13 1.41 1.25 2.04 2.27 2.68 2.72 4.54
32.5 XS 80 4.47 0.39 0.75 0.23
40 48.3 40.9 Std. 40 4.05 0.39 0.95 0.27 1.36 1.81 1.7 2.81 3.06 2.83 3.74 6.35
38.1 XS 80 5.41 0.50 1.13 0.32
Buttweld Fittings and Flanges to ASME Standards
50 60.3 52.5 Std. 40 5.44 0.68 1.45 0.41 2.22 2.83 2.77 3.13 3.74 3.52 4.65 10.89
49.2 XS 80 7.48 1.00 1.72 0.54
65 73 62.7 Std. 40 8.63 1.39 2.45 0.68 3.82 4.42 4.04 4.54 5.56 5.44 6.44 16.33
59.0 XS 80 11.41 1.82 2.95 0.91
80 88.9 77.9 Std. 40 11.29 2.18 3.45 0.91 4.08 5.22 5.44 6.12 7.37 7.26 8.5 14.51
73.7 XS 80 15.27 2.86 4.30 1.27
90 101.6 90.1 Std. 40 13.57 3.05 4.5 1.36 4.99 5.44 6.35 7.71 9.53 9.98 12.25 –
85.4 XS 80 18.63 4.1 5.9 1.81
100 114.3 102.3 Std. 40 16.07 4.2 5.7 1.59 5.94 7.48 7.37 9.53 11.79 11.79 17.24 23.23
97.2 XS 80 22.32 5.7 7.3 2.18
125 141.3 128.2 Std. 40 21.77 6.8 9.1 2.7 6.12 9.53 9.07 12.7 15.42 15.88 30.84 39.01
122.3 XS 80 30.97 10.0 11.8 3.8
150 168.3 154.1 Std. 40 28.26 10.9 13.6 3.9 8.16 11.34 12.7 16.3 19.96 20.87 34.02 49.9
146.3 XS 80 42.56 16.3 19.0 5.4
200 219.1 202.7 Std. 40 42.55 21.8 25 5.9 12.7 19.05 21.77 25.4 32.21 38.1 52.16 84.82
193.7 XS 80 64.64 33.1 33.5 8.6
250 273.1 254.5 Std. 40 60.31 38.6 41 10 17.24 25.4 31.75 35.38 44 53.34 90.36 121.56
247.7 XS 60 81.55 52 54 14
300 323.9 304.8 Std. – 73.88 57 57 15 27.22 38.1 45.36 50.8 64.41 86.18 101.6 168.74
298.5 XS – 97.46 75 77 20
350 355.6 336.6 Std. 30 81.33 73 73 28 35.38 51.26 58.97 74.39 84.37 107.05 157.4 254.92
330.2 XS – 107.39 97 93 37
400 406.4 387.4 Std. 30 93.27 98 91 35 42.48 63.5 77.11 101.6 111.58 145.15 209.11 310.71
381.0 XS 40 123.30 130 120 46
|
450 457 438.2 Std. – 105.16 120 135 40 52.62 68.04 102.51 126.1 138.35 181.89 217.27 419.12
431.8 XS – 139.15 165 190 53
Piping Systems
500 508 489.0 Std. 20 117.15 150 168 61 65.32 81.65 123.38 149.69 174.63 231.33 312.98 527.98
482.6 XS 30 155.12 200 245 82
600 610 590.6 Std. 20 141.12 220 240 77 91.63 118.84 203.21 222.23 247.21 342.92 443.16 680.39
584.2 XS – 187.26 280 350 95
Steel Centre
104
KNOW YOUR STEEL
Flanges to Australian Standards
Table D Table E Table F
Nom. Flange Drilling Flange Drilling Flange Drilling Nom.
Size Thickness Bolt Dia. of Thickness Bolt Dia. of Thickness Bolt Dia. of Size
DN No. of No. of No. of DN
0Dmm ** Cirlce Bolts 0Dmm ** Cirlce Bolts 0Dmm ** Cirlce Bolts
T3mm T6mm Bolts T10mm T11mm T6mm Bolts T10mm T11mm T6mm Bolts
Dia.mm mm Dia.mm mm Dia.mm mm
15 95 6 5 67 4 M12 95 6 6 6 67 4 M12 95 8 8 10 67 4 M12 15
20 100 6 5 76 4 M12 100 6 6 6 73 4 M12 100 8 8 10 73 4 M12 20
25 115 8 5 86 4 M12 115 8 8 7 83 4 M12 120 10 10 10 87 4 M16 25
32 120 8 6 87 4 M12 120 8 8 8 87 4 M12 135 10 10 13 98 4 M16 32
40 135 10 6 98 4 M12 135 10 10 9 98 4 M12 140 11 11 13 105 4 M16 40
50 150 10 8 114 4 M16 150 10 10 10 114 4 M16 165 11 12 16 127 4 M16 50
65 165 11 8 127 4 M16 165 11 11 10 127 4 M16 185 13 13 16 146 8 M16 65
80 185 13 10 146 4 M16 185 13 13 11 146 4 M16 205 14 15 16 165 8 M16 80
100 215 16 10 178 4 M16 215 16 16 13 178 8 M16 230 17 17 19 191 8 M16 100
125 255 17 13 210 8 M16 255 17 17 14 210 8 M16 280 19 20 22 235 8 M20 125
150 280 17 13 235 8 M16 280 17 17 17 235 8 M20 305 22 23 22 260 12 M20 150
200 335 19 13 292 8 M16 335 19 20 19 292 8 M20 370 25 28 25 324 12 M20 200
250 405 19 16 356 8 M20 405 22 25 22 356 12 M20 430 25 32 29 381 12 M24 250
300 455 22 19 406 12 M20 455 25 28 25 406 12 M24 490 29 37 32 438 16 M24 300
350 525 25 22 470 12 M24 525 25 32 29 470 12 M24 550 32 42 35 495 16 M27 350
400 580 25 22 521 12 M24 580 25 36 32 521 12 M24 610 32 47 41 552 20 M27 400
450 640 29 25 584 12 M24 640 29 41 35 584 16 M24 675 35 52 44 610 20 M30 450
500 705 32 29 641 16 M24 705 32 46 38 641 16 M24 735 38 57 51 673 24 M30 500
600 825 35 32 756 16 M27 825 38 – 48 756 16 M30 850 41 68 57 781 24 M33 600
700 910 – 35 845 20 M27 910 – – 51 845 20 M30 935 – – 60 857 24 M33 700
750 995 – 41 927 20 M30 995 – – 54 927 20 M33 1015 – – 67 940 28 M33 750
800 1060 – 41 984 20 M33 1060 – – 54 984 20 M33 1060 – – 68 984 28 M33 800
Piping Systems
900 1175 – 48 1092 24 M33 1175 – – 64 1092 24 M33 1185 – – 76 1105 32 M36 900
1000 1255 – 51 1175 24 M33 1255 – – 67 1175 24 M36 1275 – – 83 1195 36 M36 1000
1200 1490 – 60 140 32 M33 1490 – – 79 1410 32 M36 1530 – – 95 1441 40 M39 1200
Table H Table J Table R

Flange Drilling Flange Drilling Flange Drilling
Nom. Nom.
Size Thick- Thick- Size
Thickness † Dia. Bolt Dia. of Bolt Dia. of Dia. Bolt Dia. of
DN No. of nessDia. R/F No. of ness No. of DN
0Dmm R/F Cirlce Bolts 0Dmm Cirlce Bolts 0Dmm R/F Cirlce Bolts
* Bolts mm Bolts Bolts
T10mm T11mm T6mm mm Dia.mm mm *T16mm Dia.mm mm *T18mm mm Dia.mm mm
|
15 115 10 11 13 57 83 4 M16 115 16 57 83 4 M16 115 19 64 83 4 M16 15

20 115 10 11 13 57 83 4 M16 115 16 57 83 4 M16 115 19 64 83 4 M16 20
25 120 11 12 14 64 87 4 M16 120 19 64 87 4 M16 125 22 76 95 4 M16 25
32 135 11 13 17 76 98 4 M16 135 19 76 98 4 M16 135 22 76 98 4 M16 32
40 140 13 14 17 83 105 4 M16 140 22 83 105 4 M16 150 25 89 114 4 M20 40
50 165 13 16 19 102 127 4 M16 165 25 102 127 4 M20 165 25 102 127 8 M16 50
65 185 14 17 19 114 146 8 M16 185 25 114 146 8 M20 185 29 114 146 8 M20 65
80 205 16 19 22 127 165 8 M16 205 32 127 165 8 M20 205 32 127 165 8 M20 80
100 230 19 23 25 152 191 8 M16 230 35 152 191 8 M20 240 35 152 197 8 M24 100
125 280 22 27 29 178 235 8 M20 280 38 178 235 8 M24 280 41 178 235 12 M24 125
150 305 25 30 29 210 260 12 M20 305 38 210 260 12 M24 305 44 210 260 12 M24 150
200 370 32 39 32 260 324 12 M20 370 41 260 324 12 M24 370 51 260 324 12 M27 200
250 430 35 45 35 311 381 12 M24 430 48 311 381 12 M27 430 60 311 387 16 M27 250
300 490 38 52 41 362 438 16 M24 490 51 362 438 16 M27 510 70 362 457 16 M30 300
350 550 41 58 48 419 495 16 M27 550 57 419 495 16 M30 585 79 419 527 16 M33 350
400 610 44 64 54 483 552 20 M27 610 64 483 552 20 M30 640 89 483 584 20 M33 400
450 675 48 71 60 533 610 20 M30 675 70 533 610 20 M33 735 98 572 673 20 M36 450
500 735 51 78 67 597 673 24 M30 735 79 597 673 24 M33 805 105 672 730 20 M39 500
600 850 57 92 76 699 781 24 M33 750 92 699 781 24 M36 – – – – – – 600
Blank or Blind Flange Plate Flange Slip On Weld Copper Alloy

T.30 – Plate or Boss
Flat Face T.11 – Blank
Diam. 1.6mm
Weld Neck Flange
RAISED FACE
Forged or Plate Steel
T.6 – Plate or Boss or Blank, or Weldneck (except for valves)
T.18 – Plate or Blank or Weldneck (except for valves)
Flat Face Diam. 1.6mm
Raised Face
Boss Flange Notes:

- Slip On Weld Or SCR. B.S.P. (1) All dimensions are in millimetres (mm).
(2 Only metric preferred sizes listed, except for DN 750 which is a Non-preferred size.
** (3) It is impractical to use flange thickness less than 12mm for Steel Plate Flanges.
Diam. * (4) Thickness includes 1.6mm height for the Raised Face.
1.6mm
† (5) The Raised Face is non-preferred for Table “H”.
Steel Centre
Raised Face
(6) It is normal practice to supply Steel Flanges to Tables A, D, C, E, F and H. — Flat Faced.
(7) All copper alloy flanges shall be Flat Faced.
(8) All flanges shall be drilled to Standard Tables unless otherwise specified. (For Bolt dimensions see separate page).
Important: For DN 150 and DN 200 Flanges, the O.D. of pipe being used must be specified. Dimensions for Flange Tables A, C,
Flat Face K, S and T on application.
105
KNOW YOUR STEEL
I.S.O. Metric Hexagon Steel Bolts

(For use with AS.2129 Flanges)
Length
Table D Table E Table F Table H
Nominal
Bolt Flange No. XOX No. XOX XOX No. XOX
Diam. Size DN No. Bolts
Bolts Per Bolt & Nut Bolts Per Bolt & Nut Bolt & Nut Bolts Per Bolt & Nut
Per Flange
Flange Dia. x lgth Flange Dia. x lgth Dia. x lgth Flange Dia. x lgth
15 4 M12 x 40mm* 4 M12 x 40mm* 4 M12 x 40mm* 4 M16 x 45mm*
Flat Face joint 20 4 M12 x 40mm* 4 M12 x 40mm* 4 M12 x 40mm* 4 M16 x 45mm*
Steel hexagon Bolts and 40 4 M12 x 40mm* 4 M12 x 40mm* 4 M16 x 45mm* 4 M16 x 55mm*
Nuts (XOX) are recommended for 50 4 M16 x 45mm* 4 M16 x 45mm* 4 M16 x 50mm* 4 M16 x 60mm*
use within a temperature range 65 4 M16 x 45mm* 4 M16 x 45mm* 8 M16 x 50mm* 8 M16 x 60mm*
of –50˚C to +300˚C. Outside of 80 4 M16 x 45mm* 4 M16 x 45mm* 8 M16 x 50mm* 8 M16 x 65mm*
this temperature range, Stud 100 4 M16 x 45mm* 8 M16 x 45mm* 8 M16 x 60mm* 8 M16 x 70mm*
Bolts should 125 8 M16 x 45mm* 8 M16 x 50mm* 8 M20 x 70mm* 8 M20 x 80mm*
be used as recommended 150 8 M16 x 45mm* 8 M20 x 60mm* 12 M20 x 70mm* 12 M20 x 80mm*
in AS.2528. 200 8 M16 x 45mm* 8 M20 x 60mm* 12 M20 x 75mm* 12 M20 x 90mm*
A quick reference chart for sizing 300 12 M20 x 60mm* 12 M24 x 80mm* 16 M24 x 100mm* 16 M24 x 110mm*
bolts and nuts for a range of 350 12 M24 x 75mm* 12 M24 x 85mm* 16 M27 x 100mm* 16 M27 x 130mm*
I.S.O. Metric Hexagon Steel Bolt
regularly used standard flanges is 400 12 M24 x 75mm* 12 M24 x 100mm* 20 M27 x 120mm* 20 M27 x 140mm*
given below: 450 12 M24 x 80mm* 161 M24 x 100mm* 20 M30 x 130mm* 20 M30 x 160mm*
APPLICABLE TO PLATE &
700 20 M27 x 100mm* 20 M30 x 140mm* 24 M33 x 160mm*
FORGED STEEL LOOSE FLANGES
750 20 M30 x 120mm* 20 M33 x 150mm* 28 M33 x 170mm*
ONLY
800 20 M33 x 120mm* 20 M33 x 150mm* 28 M33 x 180mm*
900 24 M33 x 140mm* 24 M33 x 170mm* 32 M36 x 200mm*
Integral valve flanges quite
1000 24 M33 x 140mm* 24 M36 x 180mm* 36 M36 x 220mm*
often differ in thickness to
1200 32 M33 x 160mm* 32 M36 x 200mm* 40 M39 x 240mm*
equivalent loose flanges. When
integral flanges are involved due Notes:
allowance should be made to • All dimensions are in millimetres (mm).
bolt lengths. • High strength structural bolts to AS 1252 may be substituted for property class 8.8 bolts if agreed to by the
purchaser.
• Bolts to AS 1252 are heavy hexagon series and the selection of such bolts would be subject to space being
|
available on the relevant flange.

Piping Systems
Bolt lengths listed apply to flat-faced or 1.6mm raised face Bolt Hole Diameters
flanges with allowance for 1.6mm gasket thickness. For bolts to M24, clearance hole 2mm larger.
*For approximate Stud Bolt Lengths take the XOX Bolt Length Above M24, clearance hole 3mm larger.
and add the metric diameter in mm rounded to the nearest
XOX Bolts & Nuts
5mm increment up
XOX is the trade term used for H.R.H. commercial steel bolts
Note: (This does not include length of point)
and nuts.
This chart shows bolt diameters as recommended in AS.2129.
H.R.H. denotes Hexagon Head x Round Shank x Hexagon
Some of these are Non-preferred sizes e.g. (M27), (M33) and
Nut.
(M39) which are not readily available in Australia.
Stud Bolts should be used as alternatives to bolts where the size
is greater than M24 and it is therefore suggested that Stud Bolts XOX Bolting
as specified in AS.2528 or BS.4882 should be used.
Temp. Range: -50˚C to +300˚C
Inch series bolts interchangeable as follows:
Flange Specifications
Table Bolts Nuts
For Use For Use
D, E, F AS 1110 Gr.4.6 AS 1112 Gr.5
1/4” M6 7/8” M24 or AS 1111 Gr.4.6
5/16” M8 1” (M27) H AS 1110 Gr8.8 AS 1112 Gr.8
3/8” M10 1 1/8” M30
1/2” M12 1 1/4” (M33)
Steel Centre
5/8” M16 1 3/8” M36

3’4” M20 1 1/2” (M39)
106
Fencing and Fittings
KNOW YOUR STEEL

Fabricated Fencing
Pack
Length Weight
Description Size (cm) Finish Size
(m) (kg/roll)
(rolls)
6-70-30 200 78.0 9
Ringlock® Heavy
Heavy
Galvanised Strongline 6-90-30 200 83.0 9
Galvanised
(2.8mm Wire Top & Bottom)
7-90-30 200 93.0 9
5-70-30 200 61.0 9
5-70-90 500 114.0 5
6-70-30 200 71.0 9
6-90-30 200 73.0 9

Ringlock® Standard Galvanised Galvanised
7-90-30 200 86.0 9
7-90-60 200 69.0 9
8-90-15 100 65.0 9
8-90-30 200 95.0 9
6-70-30 200 71.0 9

6-90-30 200 73.0 9
Hinge Joint Standard 7-90-30 200 86.0 9

Galvanised
Galvanised (2.5mm Wire) 8-80-15 100 60.0 9
8-90-30 200 95.0 9
8-90-15 100 65.0 9
6-70-30 200 76.0 9
200 78.4 9
|
6-90-30
Fabricated Fencing
7-90-30 200 88.0 9
®
Zedlock Heavy 7-90-30 500 218.0 4
Heavy
Galvanised Strongline
7-90-45 Galvanised 500 193.5 MTO
(2.8mm Wire Top & Bottom)
8-90-30 200 97.5 9
13-90-15 100 86.7 MTO
15-150-15 100 111.2 MTO
6-70-30 200 71.5 9
6-70-45 200 65.0 9
7-90-30 200 84.0 9
7-90-30 Heavy 500 218.0 4

Zedlock® Heavy Galvanised
7-90-45 Galvanised 200 75.0 MTO
8-90-15 100 63.0 9
8-90-30 200 93.6 9
8-115-15 100 67.0 9
8-90-15 50 20.5 16
Zedlock® Economy Standard 8-90-15 100 41.0 9

Galvanised
Galvanised (2.0mm Wire) 8-115-15 50 22.5 16
8-115-15 100 45.0 9

Steel Centre
Zedlock® Dog Fence - Standard 12-120-15 50 29.0 MTO

Galvanised
Galvanised (2.0mm Wire) 12-120-15 100 57.0 MTO
107
KNOW YOUR STEEL
Fence Wire
Pack
Size Length Weight
Description Finish Size
(cm) (m) (kg/roll)
(rolls)
Heavy Galvanised -
2.50 1500 58 10
Plain Wire Supa-Ten High Tensile
Heavy Galvanised Heavy Galvanised -
2.50 1500 58 10
Flexi-Ten Medium Tensile
Galvanised -
2.80 1000 48 10
Supa-Ten High Tensile
Galvanised -
2.50 1500 58 10
Supa-Ten High Tensile
Plain Wire
Galvanised -
Standard 2.50 1500 58 10
Flexi-Ten Medium Tensile
Galvanised
Galvanised -
4.00 500 49 10
Soft-Ten Soft Tensile
Galvanised -
3.15 750 46 10
Soft-Ten Soft Tensile
Plain Wire Galvanised -
2.50 250 10 10
Handy Pack Flexi-Ten Medium Tensile
Fence and Trellis Wire
Standard Galvanised -
3.15 250 16 10
Galvanised Soft-Ten Soft Tensile
Plain Wire Galvanised - High
2.50 1500 58 MTO
Standard Tensile Red Tag
Galvanised Galvanised - Medium
2.50 1500 58 MTO
Red Tag Tensile Red Tag
1.60 3200 50 MTO
Tie Wire Heavy

2.00 Galvanised - Soft 2000 50 MTO
Galvanised Soft
|
2.50 1300 50 10
Trellis Wire
Pack
Size Length Weight
(cm) (m) (kg/roll)
(rolls)
2.00 2000 50 10
2.65 1000 43 10
Trellis Wire
High Tensile
Heavy Galvanised 2.85 1000 50 10
3.15 1000 61 10
Steel Centre
108
KNOW YOUR STEEL
Tie Wire
Item Category Diameter (mm) Finish Length (m) Weight (kg/roll) Pack Size (rolls)
0.7 75 0.5 20
0.90 75 0.5 20
Standard
1.25 50 0.5 20
Galvanised
1.57 30 0.5 20
2.00 20 0.5 20
Tie Wire 1.25 100 1 12

Standard
1.57 Galvanised 67 1 12
(1kg)
2.00 40 1 12

1.25 300 3 6
1.57 Standard 200 3 6

Galvanised
2.00 (3kg) 120 3 6
2.50 80 3 6
|
Tie and Barbed Wire
Barbed Wire
Pack
Size Length Weight
(cm) (m) (kg/roll)
(rolls)
IOWA Barbed
2.50 mm Galvanised 400 41.0 18
Wire - Low Tensile
Barbed Wire 1.57 mm Heavy Galvanised 500 22.0 36
- High Tensile 1.80 mm Heavy Galvanised 500 27.0 36
Barbed Wire 30 1.9 3
- High Tensile 1.57 mm Galvanised
Steel Centre
- Handy Pack 100 7.0 3
109
KNOW YOUR STEEL
Netting
Animal
Height Aperture Wire Diameter Length Pack Size Weight

Description Finish
(cm) (cm) (mm) (m) (rolls) (kg/roll)
90 1.27 2.5 x 1.24 30 5 28

Standard
Aviary Netting
Galvanised
120 1.27 2.5 x 1.24 30 5 37
Standard
Cage Mesh 90 2.5 x 1.24 30 5 18
Galvanised
Dog & Boundary Standard
120 graduated 2.0 30 5 15
Netting Galvanised
90 1.3 0.56 50 5 13.7

Bird and Vermin Standard
120 1.3 0.56 50 5 20.0
Netting Galvanised
180 1.3 0.56 50 5 29.0
90 3 0.90 50 5 20.5
Standard
Animal Netting 120 3 0.90 50 5 27.0
Galvanised
Netting
180 3 0.90 50 5 40.0
90 5 1.00 50 5 12.6
|
Chicken Standard
120 5 1.00 50 5 17.5

Netting Galvanised
180 5 1.00 50 5 26.0
Hexagonal
Height Aperture Wire Diameter Length Pack Size Weight

Description Finish
(cm) (cm) (mm) (m) (rolls) (kg/roll)
180 4 1.4 50 7 73.0
120 4 1.4 50 7 49.0
105 4 1.4 50 16 44.0
Hexagonal
105 4 1.4 100 9 87.0
Netting Heavy
- Heavy Galvanised
90 4 1.4 50 16 38.0
Galvanised
Steel Centre
90 4 1.4 100 9 75.0
60 4 1.4 50 7 26.0
30 4 1.4 100 18 28.0
110
KNOW YOUR STEEL
Posts
Length Weight
Item Category Finish
(cm) (kg)
Hot-Dipped Galvanised 150 2.85

Steely Posts
Black Bituminous 135 2.6

Steely Posts
Black Bituminous Coating
Black Bituminous 210 4

"XL" Steely Posts Black Bituminous 180 5.2

Steely Posts –Black Bituminous
coating Loose Utility Pack
|
Posts

Economy Fence Post (Rail) Black
Bituminous Coating

Economy Fence Post
Safety Yellow Post Caps

• Can be used with Cyclone economy posts, Cyclone traditional posts
and Cyclone Livestock posts
Steel Centre
• Fits most Y posts

• Bright yellow for visibility and safety
111
KNOW YOUR STEEL
Gates
Pack
Height Weight
Description Finish Width Size
(mm) (kg)
(gates)
Hot-Dipped Galvanised 1170 2370 mm (8 FT) 7 25
N-SURE Gate Hot-Dipped Galvanised 1170 4470 mm (15 FT) 7 42

Gates

|

Hot-Dipped Galvanised 1800 4170 mm (14 FT 7 49
Access Gate Hot-Dipped Galvanised 1170 1000 mm (3 FT) 7 9
Hot-Dipped Galvanised 1170 2370 mm (8FT) 7 21

Vertical Brace
Gate
Galvanised 5 Hot-Dipped Galvanised 1170 3570 mm (12 FT) 7 34

Bar Gate
4770 mm (16 FT)

Steel Centre
Hot-Dipped Galvanised 1170 7 46

Mesh Infill
112
KNOW YOUR STEEL
Universal Fence Fitting System
®
Size
Description Finish
mm
Rail Clamps Galvanized 25, 32, 40, 50
Post Clamps Galvanized 25, 32, 40, 50, 65, 80, 100
Multi Purpose Connector Galvanized
Note: All rail and post clamps are interchangeable with each other.
Rail Clamp Post Clamp Multi Purpose
Connector
Hinges & Gudgeons ®
Size
Description Finish
mm
Long Plate Gudgeons Galvanized 20NB, 25NB

Post - 50NB, 80NB
Two Part Hinges Galvanized
Gate - 25NB
Pipe Hinge Strap Galvanized 25NV
Long Plate Two Part Hinges Pipe Hinge
Gudgeons Strap
Temporary Fence Clamps
|
®
Fittings, Clamps, Hinges and Gudgeons

Fit Pipe Size mm
32 x 32, 40 x 40, 50 x 50
Hinges & Gudgeons ®
Description
FGP1 – Ring Chain Catches, Screw In with

gudgeons and clamps (Galvanized)
FGP3 – Ring Chain Catches, Screw In with

FGP3 FGP15 Socket & Pin gudgeons and clamps (Galvanized)
FGP1 FGP4 – Ring Chain Catches, Screw In with

gudgeons and clamps (Galvanized)
FGP15 – Ring Chain Catches, Screw In

with gudgeons and clamps (Galvanized)
Steel Centre
FGP4
Socket & Pin
113
Steel Centre
We are the machines and

equipment which cultivate and
house Australia’s food source.
InfraBuild Steel Centre can provide a total steel solution to simplify your farm
steel and fencing needs from start to finish. We also supply steel to the many
manufacturers who make the equipment which our farmers use.
www.infrabuild.com
Fasteners
KNOW YOUR STEEL

Shed Teks®
14 × 22 – Fine thread. 14g screws with 5/16" head size to eliminate driver changes, generally used in shed construction
with plates and cleats.
14 × 25 – Coarse thread. 14g screws with 5/16" head size to eliminate driver changes, generally used in shed construction
with plates and cleats.
AutoTeks®
M5.5 × 39 – Fixing corrugated roof sheet to steel purlins 1.9mm to 3.5mm.
M5.5 × 50 – Fixing square rib roof sheet to steel purlins 1.9mm to 3.5mm.
Rippleteks
10 × 20 – Fixing mini corrugated and corrugated sheets to steel.
10 × 30 – Fixing mini corrugated and corrugated sheets to timber.
Series 500 SuperTEKS®

12 × 32 – Wafer head for flush fit needs such as walkways. Drills 3mm to 12.5mm hot rolled steel.
12 × 32, 12 × 50, 12 × 65 – Hex head with or without seal. Drills 3mm to 12.5mm hot rolled steel for roof and wall
Fasteners
cladding, pipe and cable staddles, metal deck clips, brackets, signage and plumbing applications.
RoofZips®
M6 × 25 – Fixing wall cladding, stitching & general fastening into both timber & steel up to 1.5mm.
M6 × 50 – Fixing corrugated roof sheet to timber, metal batten & steel purlin up to 1.5mm. Also suits square profile sheet
fixed to metal battens & steel purlins up to 1.5mm.
M6 × 25 – Fixing wall cladding, stitching & general fastening into both timber & steel up to 1.5mm.
Hi-Teks® – General Purpose Fasteners

10 × 16 – Used in fencing, steel house frames, DuraGal® flooring systems, shed and wall cladding with seal.
12 × 20 – Used in fencing, steel house frames, sheds and wall cladding with seal.
14 × 22 – Used in DuraGal® flooring systems, sheds and heavier assembly.
BattenZips®
M5.5 × 40 – Fixing metal roof battens to either timber or steel rafters.
PolyZips®
M6.5 x 50 – Fixing corrugated polycarbonate sheet to timber, metal batten and steel purlin up to 1.5mm,
also suits square profile fixed to metal battens and steel purlins up to 1.5mm.
M6.5 x 65 – Fixing square profile polycarbonate sheet to timber battens.
Wingteks®
6 x 50, 8 x 32, 10 x 40, 10 x 45, 10 x 55, 10 x 75, 14 x 65 – Countersunk ribbed head for applications where
timber is fastened to steel, gates, fences, decking but not recommended for treated timber decks to steel.
Bugle Batten
14 x 50, 14 x 75, 14 x 100 – Countersunk head for fixing timber battens to rafters, fastening heavy timbers,
fencing, boardwalks, pergolas, plates and hinges to timber.
Fibreglass Teks®
Steel Centre
M6.5 x 65, M6.5 x 85 – 32mm weatherlok fixing fibreglass sheet to steel up to 3mm, drills the expansion hole
during installation.
115
General Information
KNOW YOUR STEEL
Geometry and Mensuration
Shape Area or Volume Formulae Results – Area or Volume
Rectangles Area Multiply length by width A (m) x B (m) = Square metres

Squares Area Multiply length by width A (m) x B (m) = Square metres
Cubes Volume Length x Width x Height A (m) x B (m) x H (m) = Cubic metres
Circles Circumference Multiply diameter by Pi (or 3.142858) D (m) x Pi = metres
Circles Area Pi x Radius x Radius [or R2] (R2) x Pi = Square metres
Sector of a circle Area Length of Arc x Half Radius A (m) x R/2 = Square metres
Triangles Area Base/2 x Height B/2 (m) x H = Square metres
Ellipse Area Long axis x Short axis x 0.7854 D1 (m) x D2 (m) x 0.7854 = Square metres
Ellipse Volume Long axis x Short axis x 0.7854 x Length D1 (m) x D2 (m) x 0.7854 = Square metres
Cylinder Area Circumference of base x Height D (m) x Pi x H (m) = Square metres
Cylinder Volume Area of base x Height (R2) x Pi x H (m) = Cubic metres
Sphere Area Diameter x Diameter x Pi D (m) x D (m) x Pi = Cubic metres
D (m) x D (m) x D (m) x 0.5236 =
Sphere Volume Diameter x Diameter x Diameter x 0.5236
Cubic metres
Pyramid Area Perimeter of base x Slant Height/3 [A (m) + B (m) x 2 x Slant height]/3 = Square metres
Geometry, Mensuration and Gauge Conversions
Pyramid Volume Area of base x Vertical Height/3 [A (m) + B (m) x H (m)]/3 = Cubic metres
Gauge Conversions
Conversion Factors
Imperial
mm Gauge
Decimal Inch
0.40 26
0.60 24
0.80 22 0.032 1/32
1.00 20
1.20 18 0.047 3/64
1.40 17 0.055
1.60 16 0.063 1/16
1.80 15 0.071
|
2.00 14 0.080 5/64

General Information
2.30 13 0.092 3/32

2.50 12 0.098
2.80 11 0.110
3.00 10 1.125 1/8
3.50 9 0.138
4.00 8 0.160 5/32
5.00 6 0.197 3/16
6.00 4 0.236
6.30 3 0.250 1/4
8.00 2 0.315 5/16
9.00 1 0.354
10.00 0 0.394 3/8
12.70 0.500 1/2
Steel Centre
16.00 0.625 5/8

19.00 0.750 3/4
22.00 0.875 7/8
25.40 1.000 1
116
KNOW YOUR STEEL
Conversion Tables
Mass Conversions kilos/pounds Mass Conversions tonnes/tons
Kilogram kg Pound lb Pound lb Kilogram kg Tonnes Tons Tons Tonnes
1 2.205 1 0.4536 1 0.9842 1 1.016

2 4.409 2 0.9072 2 1.968 2 2.032
3 6.614 3 1.361 3 2.953 3 3.048
4 8.818 4 1.814 4 3.937 4 4.064
5 11.02 5 2.268 5 4.921 5 5.080
6 13.23 6 2.722 6 5.905 6 6.096
7 15.43 7 3.175 7 6.889 7 7.112
8 17.64 8 3.629 8 7.874 8 8.128
9 19.84 9 4.082 9 8.858 9 9.144
10 22.05 10 4.536 10 9.842 10 10.16
50 110.2 50 22.68 50 49.21 50 50.80
100 220.5 10 45.36 100 98.42 10 101.60
Length Conversions cms/inches Length Conversions klms/miles
General Information
centimetres inches inches centimetres Kilometre Kilometre
Miles Miles
(cm) (in) (in) (cm) (km) (km)
1 0.3937 1 2.54 1 0.6214 1 1.609
2 0.7874 2 5.08 2 1.243 2 3.219
3 1.1810 3 7.62 3 1.864 3 4.828
4 1.5750 4 10.16 4 2.485 4 6.437
5 1.9690 5 12.70 5 3.107 5 8.047
6 2.3620 6 15.24 6 3.728 6 9.656
|
Conversion Tables
7 2.7559 7 17.78 7 4.350 7 11.27
8 3.1500 8 20.32 8 4.971 8 12.87
9 3.5430 9 22.86 9 5.592 9 14.48
10 3.9370 10 25.40 10 6.214 10 16.09
50 19.690 50 127.0 50 31.07 50 80.47
Conversion Tables
100 39.370 10 254.0 100 62.14 10 160.90
Pressure Conversion psi/MPa Pressure Conversion psi/MPa
psi MPa MPa psi psi MPa MPa psi
1 0.006895 0.1 14.5 1500 10.34 6.0 870.2

50 0.3447 0.2 29.01 1600 11.03 6.5 942.7
100 0.6895 0.3 43.51 1700 11.72 7.0 1015
200 1.379 0.4 58.02 1800 12.41 8.0 1160
300 2.068 0.5 72.52 1900 13.10 9.0 1305
400 2.758 0.6 87.02 2000 13.79 10.0 1450
500 3.447 1.0 145.0 2100 14.48 11.0 1595
600 4.137 1.5 217.6 2200 15.17 12.0 1740
700 4.826 2.0 290.1 2300 15.86 13.0 1885
800 5.516 2.5 362.6 2400 16.55 14.0 2031
900 6.205 3.0 435.1 2500 17.24 15.0 2176
1000 6.895 3.5 507.6 2600 17.93 16.0 2321
1100 7.584 4.0 580.2 2700 18.62 17.0 2466
Steel Centre
1200 8.274 4.5 652.7 2800 19.31 18.0 2611

1300 8.963 5.0 725.2 2900 19.99 19.0 2756
1400 9.653 5.5 797.7 3000 20.68 20.0 2901
117
KNOW YOUR STEEL
Useful Conversion Factors

Imperial to Metric (approximate)
“SI” denotes the INTERNATIONAL SYSTEM of Metric Units adopted in Australia
This table may be used in two ways:

Multiply column “A” by column “B” to obtain column “C”
Alternatively Divide column “C” by column “B” to obtain column “A”
A B C
Remarks
Multiply By To obtain
Square inches 645.16 mm2
AREA: Symbol m2 Square feet 0.929 m2
The SI unit of AREA is Square yards 0.836 m2
the SQUARE METRE. Acre 4047 m2
Hectare (ha) 10 000 m2
DENSITY: Symbol kg/m3 lb/in3 27.68 t/m3
The SI unit of DENSITY is the kilogram per lb/ft3 16.02 kg/m3
cubic metre. lb/yd3 0.5933 kg/m3
1.ELECTRICAL ENERGY
kilowatt hour (kW.h) 3.6 MJ
2.HEAT ENERGY
British thermal unit
(Btu) 1.055 kJ
Btu/gal 0.2321 kJ/L ††
Btu/ft3 37.26 kJ/M3
ENERGY: Symbol J
The SI unit of ENERGY is the JOULE.
1 J = 1 N.m
A joule is the energy expended or the work 3.MECHANICAL ENERGY
done when a force of one newton moves the foot poundal
point of application a distance of one metre ft.pdl .04214 J
in the direction of that force. inch pound-force
in.lbf 0.1130 J
foot pound-force
|
ft.lbf 1.356 J
General Information
foot ton force

ft.tonf 3.037 kJ
Metre kilogram force
m.kgf 9.807 J
FORCE: Symbol N (NEWTON) Poundal (pdl)

The SI unit of FORCE (kg.m/s2) has been Pound-force (lbf)
0.1383 N
given the special name – NEWTON. The ton-force (tonf)
4.448 N
newton is the force which when applied to a *kilogram-force (kgf)
9.964 kN
body having a mass of one kilogram, causes *also known as
9.807 N
an acceleration of one metre per second in kilopond (kp)
the direction of application of the force.
FORCE PER UNIT LENGTH: pounds-force per inch (lbf/in) 175.1 N/m
The SI unit is NEWTON PER METRE: pounds-force per foot (lbf/ft) 14.59 N/m
Symbol N/m ton-force per foot (ton/ft) 32.69 kN/m
TEMPERATURE
The SI unit of TEMPERATURE is the KELVIN - Symbol K. For most practical purposes of temperature measurement and most calculations involving
temperatures, degrees Celsius, symbol oC will be used.
Steel Centre
DEGREES FAHRENHEIT TO CELSIUS DEGREES CELSIUS TO FAHRENHEIT

(o
F - 32) x 5/9 = oC (oC x 9/5) +32 = oF
118
KNOW YOUR STEEL

A B C
Remarks
inches 25.4 millimetres (mm)
feet 0.3048 metres (m)
LENGTH: Symbol m yards 0.9144 metres (m)
The SI unit of LENGTH is the METRE. chain 20.12 metres (m)
mile 1609 metres (m)
mile 1.609 kilometres (km)
ounce 28.35 grams (g)
pound 0.4536 kilograms (kg)
slug 14.59 kg
ton (2240 lb) 1016.05 kg
MASS: Symbol kg short ton (2000 lb) 907.2 kg
The SI unit of MASS is the KILOGRAM. ton (2240 lb) 1.016 tonne (t)
General Information
pounds per foot (lb/ft) 1.488 kg/m
pounds per yard (lb/yd) 0.4961 kg/m
Btu per hour (Btu/hr) 0.2931 W

POWER: Symbol W
horsepower (hp) 0.7457 kW
The SI unit of POWER is the WATT.
ton of refrigeration 3.517 kW
6.895 kPa
lbf/in2
6.895 MPa
kip/in2 (1000 psi)
47.88 Pa
PRESSURE: Symbol Pa lbf/ft2 47.88 Pa
98.07 kPa
The SI unit of PRESSURE or stress is the kgf/cm2
|
100 kPa
NEWTON PER SQUARE METRE which has bar

been given the name PASCAL. 1 N/m2 = 1Pa Vertical column (head) of water.
9.79 kPa
= 0.000145lbf/in2 A pascal is the pressure (H20 at 20oC)
2.984 kPa
or stress which arises when a force of one metres of water
0.1333 kPa
newton is applied uniformly over an area of feet of water
0.1333 kPa
one square metre. torr (vacuum)
3.386 kPa
1mm Hg. (mercury) 1in. Hg.
101.325 kPa
(mercury) atmosphere (atm) microns
0.133 Pa
Poundal-foot
pdl.ft .04214 N.m
pound-force inch
TORQUE: Symbol N.m lbf.inch 0.1130 N.m
(Moment of force) lbf.inch 1.152 kgf.cm
The SI unit of TORQUE is the NEWTON pound-force feet
METRE. The newton metre is the work done lbf.ft 1.356 N.m
when a force of one newton moves the point lbf.ft 13.83 kgf.cm
of application a distance of one metre in the ton-force feet
direction of that force. 1 N.m = 1 J tonf.ft 3.037 kN.m
kilogram-force
kgf.m 9.807 N.m
kgf.cm 0.09807 N.m
ft. per second (ft/s) 0.3048 m/s
VELOCITY: Symbol m/s
ft. per minute (ft/min) 0.00508 m/s
The SI unit of VELOCITY
miles per hour 0.4470 m/s
is the METRE PER SECOND.
miles per hour 1.609 km/h
Steel Centre
119
KNOW YOUR STEEL

A B C
Remarks
DRY:
cubic inch (in3) 16387 mm3
cubic foot (ft3) 0.02832 m3
VOLUME: CAPACITY: Symbol m3 cubic yard (yd3) 0.7646 m3
The SI unit of VOLUME is litre (L) †† 1 000 000 mm3
the CUBIC METRE. litre (L) †† 0.001 m3
gallons (Imp.) 0.004546 m3
IMPERIAL LIQUID
NOTE: †† fluid ounce 28.41 millilitre (ml)
Capital “L” is now the legal pint (20 fl. oz) 568.3 millilitre (ml)
preferred symbol for litre quart (2 pints) 1.137 litre (L) ††
in Australia. gallon (Imp.) 4.546 litre (L) ††
gallon (US) 3.785 litre (L) ††
litre (water 4oC) 1.000 kilogram (kg)
Imp. gallons (water 20oC) 4.536 kilogram (kg)
Imp. gal. per minute (gal/min) .0000758 m3/s
VOLUME: RATE OF FLOW Symbol m3/s Imp. gal. per minute 0.272765 m3/hr
The SI unit of VOLUME RATE OF FLOW is the Imp. gal. per minute .0758 litre per second (L/s)
CUBIC METRE PER SECOND. cubic ft. per minute .000472 m3/s
cubic ft. per minute 0.472 litre per second (L/s) 1m3 = 1Kl
miles per gallon 0.3540 km per litre
SUNDRY ITEMS:
gallons per mile 2.825 litres per km
TEMPERATURE
The SI unit of TEMPERATURE is the KELVIN - Symbol K. For most practical purposes of temperature measurement and most calculations involving
temperatures, degrees Celsius, symbol oC will be used.
|
General Information
DEGREES FAHRENHEIT TO CELSIUS DEGREES CELSIUS TO FAHRENHEIT

(o o
F - 32) x 5/9 = C (oC x 9/5) +32 = oF
Handy Tips
To calculate the mass of flats, squares and rounds. To calculate the mass of steel plate sections
Flats: Width (mm) x Thickness (mm) x 0.00785 = kg/m Mass = t x 7.850 x (L x W) where:
Mass = mass/metre2
Squares: Size (mm2) x 0.00785 = kg/m
t = thickness of plate kg/m
Rounds: Diameter (mm2) x 0.006165 = kg/m L = length of plate mm
Some Mass Calculations as indicated on pages 13-15 include W = width of plate m
a 2.5 per cent rolling tolerance. To calculate the mass for Floor plate, add 2 kg/m2 m
To calculate the mass of steel circular hollow sections

(CHS) (as used in Australian Standards AS/NZS 1163)
Steel Centre
Circular sections
Mass = (OD - wt) x wt x 0.0246615.
where: Mass = mass/metre kg/m
OD = outside diameter mm
wt = section thickness mm
120
Handy Tips
KNOW YOUR STEEL

Property of Steel Symbol Value To determine the length of conveyor belting
Young’s Modulus of Elasticity E 200 x 103 MPa

Measure in inches from the outside of the roll to the
Shear Modulus of Elasticity G 80 x 103 MPa opposite side of the centre opening S. Count the number
of layers or turns of belt N.
Density p 7850 kg/m3 C is constant = 0.2618
L = S x N x C = Length in feet/3.28 = metres
Poisson’s Ratio v 0.25
eg. 26” x 61 x 0.2618 = 415.22’ divide by 3.28 = 126.6m
Coefficient of Thermal Expansion aT 11.7 x 10 -6 per °C
Relevant Australian Standards

AS 1074-1989 Steel tubes and tubulars for ordinary service
AS 1085.1:2002 Supp 2017 Railway track material - Steel rails - History (Supplement 1 to AS 1085.1-2002)
AS 1085.17:2003 (R2013) Railway track material Steel sleepers
General Information
AS/NZS 1163:2016 Cold-formed structural steel hollow sections
AS/NZS 1365:1996 (R2016) Tolerances for flat-rolled steel products
Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and mag-
AS 1397:2011/Amdt 1-2012
nesium
AS 1442:2007 (R2017) Carbon steels and carbon-manganese steels - Hot rolled bars and semi-finished products
AS 1443-2004 Carbon and carbon-manganese steel - Cold-finished bars
Wrought alloy steels - Standard, hardenability (H) series and hardened and tempered to designated mechanical
AS 1444:2007 (R2017)
properties
Hot-dipped zinc-coated, aluminium/zinc-coated or aluminium/zinc/magnesium-coated steel sheet — 76 mm pitch
|
AS 1445:2013
corrugated
Relevant Australian Standards

AS 1447:2007 (R2017) Hot-rolled spring steels
AS 1448:2007/Amdt 1-2008 Carbon and carbon-manganese steels - Forgings (ruling section 300 mm maximum)
AS 1450:2007 (R2017) Steel tubes for mechanical purposes
AS/NZS 1594:2002 (R2016) Hot-rolled steel flat products
AS/NZS 1595:1998
Cold-rolled, unalloyed, steel sheet and strip
(R2016)/Amdt 1:2014
AS 2551:1982 (R2016) Steel sheet and strip - Cold-rolled, electrolytic zinc-coated
AS 3597-2008 Structural and pressure vessel steel - Quenched and tempered plate
AS/NZS 3678:2016 Structural steel – Hot-rolled plates, floorplates and slabs
AS/NZS 3679.2-2010 Structural steel Part 1: Hot-rolled bars and sections
AS/NZS 3679.2:2016 Structural steel Part 2: Welded I sections
AS/NZS 4496:1997 (R2016) Recommended practice for the colour coding of steel products
AS/NZS 4600:2018 Cold-formed steel structures
AS/NZS 4671:2001 Steel reinforcing materials
SA TS 102:2016 Structural steel – (Technical Specification) Limits on elements added
SA TS 103:2016 Structural steel – (Technical Specification) Limits on boron in parent materials.
Steel Centre
121
Important Details
KNOW YOUR STEEL
Your Local Outlet
My Local InfraBuild Steel Centre outlet details
Phone: Fax: Email:
My Local InfraBuild Steel Centre Account Representatives
Sales:
Phone: Fax: Email:
Phone: Fax: Email:

Important Details
Credit:
Phone: Fax: Email:
Phone: Fax: Email:
My Local InfraBuild Steel Centre Account Number
A/C N:
My Industry Memberships
A/C N:
Steel Centre
122
Notes
KNOW YOUR STEEL

Notes
Steel Centre
123
Find your local
InfraBuild Steel Centre:
www.infrabuild.com
Please note that any specifications or technical data referred

to in this publication are subject to change and/or variation or
improvement without notice and no warranty as to their suitability
for any use is made. Photographs shown are representative only of
typical applications. This brochure is not an offer to trade and shall
not form any part of the trading terms in any transaction. Copyright
2023 InfraBuild Trading Pty Limited (ABN 50 007 519 646).

IBSC_Know-Your-Steel_V9_June2023

Uploaded by

Copyright:

Available Formats

IBSC_Know-Your-Steel_V9_June2023

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

IBSC_Know-Your-Steel_V9_June2023

Uploaded by

Copyright:

Available Formats

Know Your Steel

Steel Mass Reference and Product Catalogue

Know Your Steel Mass Book

Hot Rolled Structural Steel

The Infrastructure Sustainability Council’s (ISC)

InfraBuild has a range of policies and procedures that

Related ISv2.0 Credits

Rso-5, Rso-6, Rso-7, Spr-2, Spr-3, Wfs-4

KNOW YOUR STEEL

Steel Credit Points

National Branch Network

KARRATHA EMERALD ROCKHAMPTON

InfraBuild Steel Centre LOCATIONS

Safety at Our Sites

Building future s thro ug h sustainab le ste e l

Structural Sheet and Coil Building Products

Billets 23 Carbon Steel Buttweld Fittings 101

It's all About Integrity

Size Mass Metres

125 x 125 x 8 14.9 67

Typical Uses: Features:

• Residential Construction • Up to 20% stronger for improved

Size Mass Metres

Typical Uses: Features:

Construction • Requires no special pre-heating

Metric Size Mass Metres

Call your local branch to discuss your requirements

Metric Mass Size Metres

700 WB 115 692 x 250 8.70

1000 WB 258 1010 x 350 3.88 Construction

1000 WB 322 1024 x 400 3.11

1200 WB 249 1170 x 275 4.02

Taper Flange Beams

Size Mass Metres

100 x 45 7.20 139

Typical Uses: Features:

Metric Mass Size Metres

Metric Mass Size Metres

500 WC 290 506 x 500 3.45 Lead times may apply.

Parallel Flange Channels

Size Mass Metres

Typical Uses: Features:

• Transport and Storage for welding.

Rely on the strength of 300PLUS®

Call your local branch to discuss your requirements

Size Mass Metres

Typical Uses: Features:

Size Mass Metres

Flat Bars - Round Edge

Size Mass Metres

Typical Uses: Features:

Flat Bars - Square Edge

Size Mass Metres

Size Mass Metres

Flat Bars - Square Edge

Flat Bars - Square Edge

Size Mass Metres

200 x 6 9.66 104

Typical Uses: Features:

Size Mass Metres