Sika MonoTop®-610 BONDING PRIMER AND REINFORCEMENT CORROSION PROTECTION CEMENT BASED SLURRY
DESCRIPTION CHARACTERISTICS / ADVANTAGES
Sika MonoTop®-610 is a cementitious, polymer modi- ▪ Easy to use, just add water fied one-component coating material containing silica ▪ Good adhesion to concrete and steel fume used as bonding primer and reinforcement cor- ▪ Good resistance to water and chloride penetration rosion protection. ▪ Can be applied with a brush or by wet spray tech- Suitable for use in hot and tropical climatic conditions. nique ▪ Good mechanical strength USES ▪ Suitable as a bonding primer as part of a concrete re- pair system ▪ Suitable as reinforcement corrosion protection as part of a concrete repair system
PRODUCT INFORMATION Chemical base Portland cement, silica fume, re-dispersible polymer powder, selected ag- gregates and additives Packaging 25 kg bags Appearance / Colour Pink / grey powder Shelf life 12 months from date of production. Storage conditions Store properly in undamaged original sealed packaging, in dry cool condi- tiones between +5 °C and +35 °C. Protect from direct sunlight, heat and moisture.
TECHNICAL INFORMATION Tensile Strength in Flexure ≥ 5.5 N/mm2 (w/p=0.2) (ASTM C348)
Tensile Adhesion Strength ~2.0 MPa (28 d) (w/p=0.2) (EN 1542)
APPLICATION INFORMATION Mixing Ratio For brush application ~5.25 litre water (21%) per 25 kg bag For spraying application ~5.0 litre water (20%) per 25 kg bag Fresh Mortar Density ~2.0 kg/l
Product Data Sheet
Sika MonoTop®-610 May 2018, Version 01.01 020302020010000001
1/3 Consumption As Bonding Primer - This depends on the substrate roughness and thick- ness of layer applied. As a guide, ~1.5 - 2.0 kg of powder per m2 per mm thick. As Reinforcement Corrosion Protection - As a guide, ~2.0 kg of powder per m2 per 1 mm layer thickness Yield 25 kg of powder yields approximately 15.0 litres Layer Thickness As bonding primer - sufficient to coat the concrete surface in a thin layer filling uneveness, pores and pits. As reinforcement corrosion protection - 2 mm minimum thickness Ambient Air Temperature +5 °C minimum; +35 °C maximum Substrate Temperature +5 °C minimum; +35 °C maximum Pot Life ~100 minutes (+20 °C) Waiting Time / Overcoating Apply concrete repair wet on wet with bonding primer Apply concrete repair wet on dry reinforcement corrosion protection
APPLICATION INSTRUCTIONS CURING TREATMENT
SUBSTRATE QUALITY / PRE-TREATMENT As reinforcement corrosion protection - protect the
fresh mortar immediately from premature drying and Concrete: contamination using an appropiate curing method. The concrete shall be thoroughly clean, rough, free from dust, loose material, surface contamination and CLEANING OF EQUIPMENT materials which reduce bond or prevent suction or Clean all tools and application equipment with water wetting by repair materials. De-laminated, weak, dam- immediately after use. Hardened material can only be aged and deteriorated concrete and where necessary mechanically removed. sound concrete shall be removed by suitable means. Steel Reinforcement: Rust, scale, mortar, concrete, dust and other loose and IMPORTANT CONSIDERATIONS deleterious material which reduces bond or contrib- ▪ Avoid application in direct sun and/or strong wind utes to corrosion shall be removed. Surfaces shall be and/or rain prepared using abrasive blast cleaning techniques or ▪ Do not add water over the recommended dosage high pressure water-blasting to Sa 2 (ISO 8501-1). ▪ Apply only to sound, prepared substrates MIXING ▪ Refer to the Method Statement for Concrete Repair using Sika MonoTop® system for more information Sika MonoTop®-610 can be mixed with a low speed (<500 rpm) hand drill mixer. BASIS OF PRODUCT DATA Pour the recommended water in a suitable mixing con- tainer. While stirring slowly, add the powder to the All technical data stated in this Data Sheet are based water and mix thoroughly at least 3 minutes. on laboratory tests. Actual measured data may vary due to circumstances beyond our control. APPLICATION LOCAL RESTRICTIONS As Bonding Primer: Thoroughly pre-wet the prepared substrate a recom- Note that as a result of specific local regulations the mended 2 hours before application. Keep the surface declared data and recommended uses for this product wet and do not allow to dry. Before application re- may vary from country to country. Consult the local move excess water e.g. with a clean sponge. The sur- Product Data Sheet for the exact product data and face shall appear a dark matt appearance without uses. glistening and surface pores and pits shall not contain water. Application by clean brush, roller or suitable spraying equipment cover the substrate in a thin layer filling all unevenness, pits and pores. As Reinforcement Corrosion Protection: Using a suitably clean brush or spraying equipment ap- ply a first layer to cover the reinforcement bars ap- proximately 1 mm thick. When first coat is hard to the finger nail, apply second layer approximately 1 mm thick. If using a spray method, protect substrate from excessive over-spray, wiping away any accumulation of material and wait until Sika MonoTop®-610 cured, be- fore to apply repair mortar ('wet on dry' application).
Product Data Sheet
Sika MonoTop®-610 May 2018, Version 01.01 020302020010000001
2/3 ECOLOGY, HEALTH AND SAFETY For information and advice on the safe handling, stor- age and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety-re- lated data.
LEGAL NOTES The information, and, in particular, the recommenda- tions relating to the application and end-use of Sika products, are given in good faith based on Sika's cur- rent knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommenda- tions. In practice, the differences in materials, sub- strates and actual site conditions are such that no war- ranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recom- mendations, or from any other advice offered. The user of the product must test the product’s suitability for the intended application and purpose. Sika re- serves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.
SIKA NORTHERN GULF SIKA SOUTHERN GULF SIKA SAUDI ARABIA
