Scribd
Upload
8 views

Code Converters

Uploaded by

Aritra Mallick
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
8 views

Code Converters

Uploaded by

Aritra Mallick
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Hybrid Electronics Laboratory

Design and Simulation of Various Code Converters

Aim: To Design and Simulate Binary to Gray, Gray to Binary , BCD to Excess 3, Excess 3 to
BCD code converters.

Objectives:
1. To understand different codes

2. To design various Code converters using logic gates

3. To simulate various code converters

4. To understand the importance of code converters in real life applications

Theory

Binary Codes

A symbolic representation of data/ information is called code. The base or radix of the
binary number is 2. Hence, it has two independent symbols. The symbols used are 0 and 1. A
binary digit is called as a bit. A binary number consists of sequence of bits, each of which is
either a 0 or 1. Each bit carries a weight based on its position relative to the binary point. The
weight of each bit position is one power of 2 greater than the weight of the position to its
immediate right. e. g. of binary number is 100011 which is equivalent to decimal number 35.

BCD Codes

Numeric codes represent numeric information i.e. only numbers as a series of 0’s and 1’s.
Numeric codes used to represent decimal digits are called Binary Coded Decimal (BCD) codes.
A BCD code is one, in which the digits of a decimal number are encoded-one at a time into
group of four binary digits. There are a large number of BCD codes in order to represent decimal
digits0, 1, 2 …9, it is necessary to use a sequence of at least four binary digits. Such a sequence
of binary digits which represents a decimal digit is called code word.

Gray Codes

It is a non-weighted code; therefore, it is not a suitable for arithmetic operations. It is a


cyclic code because successive code words in this code differ in one bit position only i.e. it is a
unit distance code.

Applications of Gray Code:


In instrumentation and data acquisition systems, where linear or angular displacement is
measured. In shaft encoders, input-output devices, A/D converters and the other peripheral
equipment.

Excess-3 code

It is a non-weighted code. It is also a self-complementing BCD code used in decimal


arithmetic units. The Excess-3 code for the decimal number is performed in the same manner as
BCD except that decimal number 3 is added to the each decimal unit before encoding it to
binary.

Code Converters

The availability of a large variety of codes for the same discrete elements of information
results in the use of different codes by different digital systems. It is some time necessary to use
the output of one system as the input to the other. The conversion circuit must be inserted
between the two systems if each uses different codes for the same information. Thus a code
converter is a circuit that makes the two systems compatible even though each uses the different
code.

Binary to Gray code

Truth Table:
Equations:

Diagram:

Logic diagram for Binary to Gray Convertor is given below:


Equations:

Diagram:
BCD to Excess-3:

To convert from binary code A to binary code B, the input lines must supply the bit
combination of elements as specified by code A and the output lines must generate the
corresponding bit combination of code B. A combinational circuit performs this transformation
by means of logic gates. As we want to design 4-bit code, we must use four input variables and
four output variables. Designate the four input binary variables by the symbols A,B,C,D, and the
four output variables by w, x, y, and z. The truth table relating the input and output variables is
as shown. A two-level logic diagram may be obtained directly from the Boolean expressions
derived by the maps. The expressions obtained may be manipulated for the purpose of using
common gates for two or more outputs. This manipulation illustrates flexibility obtained with
multiple-output systems when implemented with three or more levels of gates.

Truth table:

Equations:

z=D

y = CD+C’D’=CD(C+D)’

x = B’C+B’D+BC’D’= B’(C+D) +BC’D’

x = B’(C+D) +B(C+D)’

w= A+BC+BD=A+B(C+D)
Diagram:

Logic Diagram for BCD to Excess-3 Code Converter

Excess-3 to BCD :

The truth table relating the input and output variables is as shown.

Equations:
Diagram:

Logic Diagram for Excess-3 to BCD Code Converter

Procedure:
1. Select appropriate code converter from tab menu.

2. Run / execute the simulation by pressing the run button and observe the output of code
converters on the output LED.

3. Repeat the procedure for different inputs and note down the corresponding outputs.
Screen Shots:
Results

Binary to gray, gray to binary, Binary coded decimal (BCD) to Ex-3 code converter are
simulated and the truth table are verified.

Conclusion

Using basic logic gates, universal logic gates and derived logic gates different code
converters can be implemented and simulated.

Assignment

1. Design a code converter that converts a decimal digit from 8,4, -2,-1 code to BCD

2. Design a 5211 to 4211 code converter

3. Design 8 bit Binary to gray code converter and vice versa. Also explain its typical application.

You might also like