0% found this document useful (0 votes)
75 views4 pages

Implementing AnyConnect IKEv2 VPNs On ASA and Routers

Uploaded by

ha33yp0tt3r69
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
75 views4 pages

Implementing AnyConnect IKEv2 VPNs On ASA and Routers

Uploaded by

ha33yp0tt3r69
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Implementing AnyConnect IKEv2 VPNs on ASA and Routers

1. AnyConnect Overview

Cisco AnyConnect is a VPN client software used to connect securely to a corporate network.
It supports multiple VPN protocols, including IKEv2, which is a highly secure and efficient
VPN protocol for remote access.

2. Prerequisites

• ASA: Cisco Adaptive Security Appliance with AnyConnect Premium license.


• Router: Cisco router with IKEv2 support and any necessary VPN licenses.
• AnyConnect Client: Installed on the remote user's device.

3. Configure IKEv2 VPN on ASA for AnyConnect

1. Enable IKEv2 on ASA

bash
Copy code
crypto ikev2 enable outside

2. Configure a Trustpoint for Certificate Authentication

bash
Copy code
crypto trustpoint vpn-cert
enrollment self
subject-name CN=asa.example.com
revocation-check none
rsakeypair vpn-key
crypto ca trustpoint vpn-cert

3. Create a VPN Policy


o Define the IKEv2 policy, such as encryption, integrity, and DH group.

bash
Copy code
crypto ikev2 policy 10
encryption aes-256
integrity sha256
group 14
prf sha256
lifetime 86400

4. Create a Tunnel Group for AnyConnect


o Specify the authentication method and connection settings.

bash
Copy code
tunnel-group AnyConnect type remote-access
tunnel-group AnyConnect general-attributes
default-group-policy DfltGrpPolicy
tunnel-group AnyConnect ipsec-attributes
ikev2 remote-access enable

5. Enable AnyConnect Client and Licensing


o Activate AnyConnect and assign the necessary licenses.

bash
Copy code
webvpn
anyconnect image disk0:/anyconnect-win-4.x.x.pkg
anyconnect enable

6. Configure the VPN Group Policy


o Configure group policies to define which resources are accessible.

bash
Copy code
group-policy DfltGrpPolicy internal
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev2

7. Configure NAT Exemption for VPN Traffic

bash
Copy code
object network VPN-NAT-EXEMPT
subnet 10.1.1.0 255.255.255.0
nat (inside,outside) source static any any destination static any any
no-proxy-arp route-lookup

8. Apply Access Control and VPN Rules


o Define access control rules to secure the VPN connection.

bash
Copy code
access-list outside_access_in extended permit ip any 10.1.1.0
255.255.255.0

9. Apply VPN Policies to the Interface


o Apply the VPN settings to the ASA's external interface.

bash
Copy code
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 203.0.113.1 255.255.255.0
no shutdown

4. Configure IKEv2 VPN on Router for AnyConnect

1. Enable IKEv2 on the Router

bash
Copy code
crypto ikev2 enable GigabitEthernet0/1
2. Configure IKEv2 Policy
o Define encryption and integrity methods.

bash
Copy code
crypto ikev2 policy 10
encryption aes-256
integrity sha256
group 14
prf sha256
lifetime 86400

3. Create a VPN Tunnel Interface

bash
Copy code
interface Tunnel0
ip address 10.0.0.1 255.255.255.0
tunnel source GigabitEthernet0/0
tunnel mode ipsec ipv4

4. Configure IPsec Settings

bash
Copy code
crypto ipsec transform-set VPN-SET esp-aes-256 esp-sha-hmac
crypto map VPN-MAP 10 ipsec-isakmp
set peer 203.0.113.1
set transform-set VPN-SET
match address 101

5. Apply the Crypto Map to the Physical Interface

bash
Copy code
interface GigabitEthernet0/0
crypto map VPN-MAP

6. Configure ACLs for VPN Traffic

bash
Copy code
access-list 101 permit ip 10.0.0.0 0.0.0.255 192.168.1.0 0.0.0.255

5. Testing and Troubleshooting

• Verify VPN Status on ASA:

bash
Copy code
show vpn-sessiondb anyconnect
show crypto ikev2 sa
show crypto ipsec sa

• Verify VPN Status on Router:


bash
Copy code
show crypto ikev2 sa
show crypto ipsec sa

• Troubleshooting Tips:
o Ensure the VPN client is using the correct AnyConnect version.
o Ensure the local firewall allows VPN traffic on the required ports (e.g., UDP
500, 4500).
o Check logs for IKE negotiation issues or IPsec failures.

6. Considerations

• Use certificates for authentication whenever possible to increase security.


• Regularly monitor VPN usage and performance.
• Ensure the ASA or router has sufficient resources to handle the expected number of
concurrent VPN connections.

You might also like