Scribd
Upload
5 views

Arduino Test final

Uploaded by

yejixx999
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
5 views

Arduino Test final

Uploaded by

yejixx999
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

makle thi 2 codes on 1 sketch

const int sensor1Pin = A0; // Analog pin for moisture sensor


const int outputPin1 = 3; // Digital pin for controlling an output (e.g., an
LED)
int moistureValue;

// Sensor 2 Setup
const int sensor2Pin = A1; // Analog pin for moisture sensor
const int outputPin2 = 4; // Digital pin for controlling an output (e.g., an
LED)
int moistureValue2;

// Sensor 3 Setup
const int sensor3Pin = A2; // Analog pin for the water level sensor
const int buzzerPin = 8; // Digital pin for the buzzer
const int threshold = 500; // Threshold for the water level sensor

void setup() {
pinMode(outputPin1, OUTPUT);
pinMode(outputPin2, OUTPUT);
pinMode(buzzerPin, OUTPUT);
Serial.begin(9600);
Serial.println("Reading from sensors...");
}

void loop() {
// Reading from Sensor 1
moistureValue = analogRead(sensor1Pin);
moistureValue = map(moistureValue, 550, 10, 0, 100);
Serial.print("Moisture: ");
Serial.print(moistureValue);
Serial.println("%");

if (moistureValue > 0) {
digitalWrite(outputPin1, HIGH); // Turn on the output if moisture value is
above 0
} else {
digitalWrite(outputPin1, LOW); // Turn off the output if moisture value is 0
or below
}

// Reading from Sensor 2


moistureValue2 = analogRead(sensor2Pin);
moistureValue2 = map(moistureValue2, 550, 10, 0, 100);
Serial.print("Moisture: ");
Serial.print(moistureValue2);
Serial.println("%");

if (moistureValue2 > 0) {
digitalWrite(outputPin2, HIGH); // Turn on the output if moisture value is
above 0
} else {
digitalWrite(outputPin2, LOW); // Turn off the output if moisture value is 0
or below
}

// Reading from Sensor 3


int sensor3Value = analogRead(sensor3Pin);
Serial.print("Sensor 3 Value: ");
Serial.println(sensor3Value);

if (sensor3Value < threshold) {


digitalWrite(buzzerPin, HIGH); // Turn buzzer on
} else {
digitalWrite(buzzerPin, HIGH); // Turn buzzer on for 200ms
delay(200);
digitalWrite(buzzerPin, LOW); // Turn buzzer off
delay(200);
}

delay(1000); // Delay for stability


}

and this

#include <Wire.h>
#include <LiquidCrystal_I2C.h>

// Create an LCD object with I2C address 0x27 (common for many I2C LCDs)
LiquidCrystal_I2C lcd(0x27, 16, 2);

// Define the analog pins for the sensors


const int sensor1Pin = A0;
const int sensor2Pin = A1;
const int sensor3Pin = A2;

// Define threshold for the sensor3 to determine water presence


const int waterThreshold = 500; // Adjust based on sensor calibration

// Define maximum sensor values observed


const int maxSensorValue = 1023; // Assuming 10-bit ADC resolution

void setup() {
// Initialize the LCD
lcd.begin();
lcd.backlight(); // Turn on the backlight (if applicable)

// Print initial messages to the LCD


lcd.setCursor(0, 0);
lcd.print("S1: % S2: %");
}

void loop() {
// Read the moisture levels from the sensors
int sensor1Value = analogRead(sensor1Pin);
int sensor2Value = analogRead(sensor2Pin);
int sensor3Value = analogRead(sensor3Pin);

// Check if the sensor value is within a reasonable range (e.g., 0 to 1000)


int maxSensorReading = 1000; // Adjust this based on your sensor's expected range
if (sensor1Value > maxSensorReading) sensor1Value = maxSensorReading;
if (sensor2Value > maxSensorReading) sensor2Value = maxSensorReading;

// Convert the sensor readings to percentages


int sensor1Percent = map(sensor1Value, 0, maxSensorReading, 0, 100);
int sensor2Percent = map(sensor2Value, 0, maxSensorReading, 0, 100);
// Clear the first line and update it with the new sensor values
lcd.setCursor(0, 0);
lcd.print("S1:");
lcd.print(sensor1Percent);
lcd.print("% S2:");
lcd.print(sensor2Percent);
lcd.print("%");

// Clear the second line


lcd.setCursor(0, 1);
lcd.print(" "); // Clear previous message

// Check the sensor3 for water presence


lcd.setCursor(0, 1);
if (sensor3Value < waterThreshold) {
lcd.print("Tank: Water OK");
} else {
lcd.print("Tank: No Water");
}

// Wait for a second before updating


delay(1000);
}

You might also like