Htf and Vhtf

HELICAL COIL
THERMAL FLUID HEATERS

MODEL HTF and VHTF
For High Temperature Heat Transfer Systems
Capacities from 250,000 – 16,000,000 BTU/Hr.

Available Horizontal and Vertical
 LOW FIRST COST  Fluid Temperatures to 750°F

 Complete Factory Package  Rugged Steel Shell with Structural
Steel Saddles
 Safe, Automatic Operation
 Shell Internally Insulated with Ceramic
 ASME Code Construction
Fiber Blanket
 Forced Draft Burner
 All Coil Supports Located Out of
 Heat Recovery Options Radiant Section
 Limited 5-Year Warranty on Coil  Peepsights for Viewing Flame
 Single Source Responsibility  Automatic Burner Controls
 2 Pass Design for Efficiency
12711 Townepark Way / LOUISVILLE, KY 40243

800-665-4251 / 502-962-2883 / FAX 502-9244-4046
DESIGN ADVANTAGES AND BENEFITS
Models HTF and VHTF Helical Coil Thermal Fluid Heaters
 Two-Pass Design – radiant- and convection-pass  Conservative Design – increases equipment life
for efficient operation. and reduces downtime.
 High Temperatures with Low Pressures – First  Factory-Trained Service Personnel – available
Thermal Heaters can operate at, or near, for start up, operator training, and fast emergency
atmospheric pressure at temperatures as high as service.
750°F. (A pressure of more than 3,000 psi would
be required to produce the same temperature with  Computer Design – for each job for proper flux,
steam). film, and tubewall temperatures, velocity, T and
P to stay well within the limitations of the thermal
 Highly Effective Insulation – shell internally lined
fluid and materials of construction for long life and
with multi-layered ceramic fiber blanket with an
to fit your system requirements.
average K factor of 0.46.
 Completely Packaged – burner, burner controls  Special Controls and Construction Options –
and control panel including temperature indicators, include systems to meet FM or IRI insurance
pressure switches and fluid-flow protection – all requirements or other insurance or customer
pre-piped, wired and factory-tested for proper, fully standards, burner management systems
automatic operation. incorporating PLC’s, sandblasting and application
of special coatings for protection against corrosive
 Efficient Burner – with forced draft, low-excess air atmospheres. Many other options available to
and high-turndown ratio for all commercially meet your system requirements.
available gases or liquid fuels.
 Limited 5-Year Coil Warranty – is available on
 Proportioning Control – to match normal range of First Thermal Heaters for most applications thus
heat demand. Automatic off-on operation for very providing you with financial protection that isn’t
low heat load. available from most manufacturers.
 Control Panel – with full programming combustion  Pipe Coil Supports of Stainless Steel – not
safeguard (ultra-violet detection), fluid temperature exposed to radiant heat.
and pressure controls, motor starters, relays,
operating switches and lights to indicate operating  ASME Code Pipe Coil
conditions. NEMA 1 (standard) with optional Cons truction
NEMA ratings available for any need.
 Low Maintenance and Long Life – thermal fluid

does not cause scale or corrosion.
Model VHTF – Vertical saves valuable plant space.
Allows quick and easy draining of coil by gravity.
Model HTF
Horizontal offers economical design with maximum accessibility.
1. Rugged steel shell.
2. Coil supports.
3. Structural steel shell
support.
4. ASME Code pipe coil.
5. Peepsights.
6. Forced draft burner
available for wide
choice of fuels, turndowns, emissions and fuel efficiencies.
7. Bolted access door for easy access to internals.
8. Shell insulated with low density ceramic fiber blanket for low skin temperature and heat sink.
9. Burner and controls mounted for easy access.
10. ANSI 300# flanges for thermal fluid connections.
12711 Townepark Way / LOUISVILLE, KY 40243 / 800-665-4251 / 502-962-2883 / FAX 502-244-4046

TYPICAL APPLICATIONS
For First Thermal Helical Coil Heaters
• Heating evaporators • Molding plastic or
rubber products • Textile heat setting • Heating
resin kettles • Processing paints and varnishes •
Manufacturing linoleum and vinyl floor
coverings • Melting asphalt •
Heating dyes • Processing food products •
Heating platens • Melting soft metals • Heating
drying ovens • Drying and baking enamels •
Heating chemical reactors • Deodorizing
animal and vegetable oils • Evaporating high-
boiling materials • Heating chemical process
equipment • Desulphurizing, dehydrating and
odorizing gas • Heating revolving rolls to high
temperatures • Comfort heating • Snow
melting • Pipe tracing • Heat for synthetic
fiber manufacturing
Our technical staff will be happy to help

with advice about any other specialized
applications you might need.
HIGH TEMPERATURE HEAT TRANSFER FLUIDS

Fluids Temp°F 300 350 400 450 500 550 600 650 700 750 800
DOWTHERM A/ MONSANTO VPI* .............................
DOWTHERM G ...............................................................
THERMINOL 55 ..............................................................
THERMINOL 59 ..............................................................
THERMINOL 66 ..............................................................
THERMINOL 75 ..............................................................
CALFLO AF .....................................................................
CALFLO HTF ..................................................................
SYLTHERM 800 ..............................................................
MULTITHERM PG1 / PARATHERM NF ......................
MULTITHERM IG2 / PARATHERM HE .......................
MOBILTHERM 603.........................................................
* Vapor or Liquid Phase Operations. Others Liquid Phase Only. The above chart is shown to provide
a general picture of many of the
KEY TO ABOVE BOILING POINT commonly used thermal fluids.
MAXIMUM OPERATING (BULK) TEMPERATURE Consult the fluid manufacturer for
MAXIMUM FILM TEMPERATURE complete specifications.
Look to First Thermal Heaters for experience, quality control and dependable service! We have hydrostatic testing
facilities, test area for electrical checks, and the skilled technicians for any job, including complete system packaging. You
can count on First Thermal Heaters to maintain your critical production specifications and timetable!
12711 Townepark Way / LOUISVILLE, KY 40243 / 800-665-4251 / 502-962-2883 / FAX 502-244-4046

Htf and Vhtf

Uploaded by

Copyright:

Available Formats

Htf and Vhtf

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Htf and Vhtf

Uploaded by

Copyright:

Available Formats

HELICAL COIL

THERMAL FLUID HEATERS

For High Temperature Heat Transfer Systems

Capacities from 250,000 – 16,000,000 BTU/Hr.

 LOW FIRST COST  Fluid Temperatures to 750°F

12711 Townepark Way / LOUISVILLE, KY 40243

 Low Maintenance and Long Life – thermal fluid

12711 Townepark Way / LOUISVILLE, KY 40243 / 800-665-4251 / 502-962-2883 / FAX 502-244-4046

Our technical staff will be happy to help

HIGH TEMPERATURE HEAT TRANSFER FLUIDS

12711 Townepark Way / LOUISVILLE, KY 40243 / 800-665-4251 / 502-962-2883 / FAX 502-244-4046

You might also like