TABLE OF CONTENTS

CHAPTER NO.

TITLE ABSTRACT LIST OF FIGURES LIST OF TABLES

PAGE NO. v vi vii

1.
1.1.

INTRODUCTION
POWER GENERATION AND IRRIGATION BY USING WIND MILL

1
2

2.

LITERATURE REVIEW
PARTS OF A WINDMILL: 2.1 ANEMOMETER. 2.2 GENERATORS ..... 2.2.3 DESIGN OF ALTERNATOR 2.3 ROTOR 2.3.1 DESIGN OF THE ROTOR 2.4 FURLING AND SHUTDOWN SYSTEMS 2.5 SLIP RINGS

6 6 7 8 9 12 15

AIM

16

PLAN OF WORK
4.1 SELECTION OF PROJECT 4.2 DESIGN AND DRAWINGS 4.3 PURCHASE CONSIDERATION 4.4 FABRICATION 4.5 ASSEMBLY OF THE PARTS 4.6 COST ESTIMATION 4.7 REPORT

18
19 19 20 20 20 20 20

5 6 7 8 9 10 11

DESIGN OF BELT DRIVE ADVANTAGES OF WINDMILL COST ESTIMATION SUMMARY CONCLUSION REFERENCE BIBLIOGRAPHY

21 24 26 28 29 31 32

INTRODUCTION

CHAPTER 1 INTRODUCTION 1.1 POWERGENERATION AND IRRIGATION BY USING WINDMILL.

A windmill is an engine that is powered by the wind to produce energy. The energy windmills produce can be used in many ways, traditionally for grinding grain or spices, pumping water, sawing wood or hammering seeds. Modern wind power machines are used for generating electricity and are more commonly called wind turbines. Wind power is the

conversion of wind energy into a useful form of energy, such as using wind turbines to make electricity, windmills or sails to propel ships. Wind energy, as an alternative to fossil, is plentiful, renewable , widely distributed, clean, and produces no greenhouse gas emissions during operation. However, the construction of wind farms is not universally welcomed because of their visual impact but any effects on the environment are generally among the least problematic of any power source. The main advantages of wind energy by comparing other modes of power for mechanical power, wind pumps for pumping water or drainage,

sources in environmentally, it reduces carbon dioxide, along with other greenhouse gas emissions, which contributes to counter measuring climate change and also, it does not

contribute to any loss to water circulation in eco-systems. Wind power does not generate solid nor gaseous polluting waste. Socially and economically, the cost of wind energy is stable, since it is not affected by fuel market price fluctuations. Wind power, comparing to other energy sources, provides the best guarantee of preserving natural rural landscape. Wind turbines occupy little amount of space and may easily coexist with agriculture.

LITERATURE REVIEW

CHAPTER-2 LITERATURE REVIEW

In this conceptual project, we are designing a wind will used to generate power for irrigation purpose. T he concerned different parts of a windmill and the parts are discussed here.

FIGURE 2.1 4

BLOCK DIAGRAM OF GENERATION OF ELECTRFICAL POWER TO IRRIGATION PURPOSE

FIGURE 2.2 ARRANGEMENT:

FIGURE2.3

PARTS OFA WINDMILL: 2.1 ANEMOMETER

It is essential to know the real wind speed in any wind generator installation, commercial or homemade. This allows you to see if the machine is performing correctly, and extremely high wind speeds might be a clue that you should shut the mill down for the duration of the storm.

2.2 GENERATORS
The alternator or generator is the heart of your wind machine, and it must be both properly sized to match your swept area, and produce the right type and voltage of power to match your application. In view of various considerations such as operational situations generator can be classified into two types. Single Phase Three Phase

Single Phase vs. Three Phase: Three phases offers some advantages over single phase in most alternators. Most small commercial wind turbines use 3 phase alternators. . Older single phase alternators we made vibrate much more (and make more noise) than 3 phase machines. Speed--The shaft speed is a very crucial factor in all types of alternator and generator. The unit needs to make higher voltages at lower rpms, otherwise it is not suited for wind power use.

This goes for all power units, even motors used as generators and alternators should be rated for low rpms. Start-Up Speed--This is the wind speed at which the rotor starts turning. It should spin smoothly and easily when you turn it by hand, and keep spinning for a few seconds. 6

Designs that 'cog' from magnetic force or that use gears or pulleys to increase shaft speed will be poor at start up. A good design can start spinning in 5 mph winds and cut in at 7 mph. Cut-In Speed--A wind generator does not start pushing power into the battery bank until the generator or alternator voltage gets higher than the battery bank voltage. Higher shaft speed means higher voltage in all generators and alternators, and you want to try and get the highest shaft speed possible in low winds--without sacrificing high-wind performance. Most commercial wind generators cut in at 8-12 mph. The generator's lowspeed voltage performance, the design of the rotor (the blades and hub), and the wind behavior all factor into where cut-in will occur.

Inefficiency--Every generator has a certain speed at which it runs most efficiently. But since the wind is not constant, we must try to design to a happy medium. As the wind speed rises, the raw power coming into the generator from the wind becomes more than the generator can effectively use, and it gets more and more inefficient. This power is wasted as heat in the stator coils.

2.2.3 DESIGN OF ALTERNATOR: 2.2.3.1 BEARINGS It has to withstand vibration and high rotation speed, there is a significant amount of thrust back on the bearings from the wind, and it increases geometrically as the prop size increases. 2.2.3.2 AIR GAP This is the distance between the magnets and the laminates in a single magnet rotor design, or between two magnets in a dual magnet rotor design. The smaller the distance, the better the alternator performs. 7

This means it's important to keep the coils as flat as possible, and to make the armature fit very precisely near the stator,if it is not perfectly square, the air gap will be larger on one side of the alternator than the other, and performance will be compromised. Halving the airgap gives 4 times as much magnetic flux. 2.2.3.3 NUMBER OF POLES A 'pole' is either the North or South pole of a magnet. Generally when building an alternator we need a seperate magnet for each pole. The faster that alternating north and south magnets poles pass the coils, the more voltage and current are produced. But surface area is important as well. 2.2.3.4 MAGNETS The stronger, the better. The larger and stronger your magnets are, the more power you can produce in a smaller alternator. 2.2.3.5 WIRE Enameled magnet wire is always used for winding the stator, because the insulation is very thin and heat-resistant. This allows for more turns of wire per coil. the gauge of wire is yet another trade off--thinner gauge wire allows for more turns per coil and thus better voltage for low-speed cut-in, but using longer, thinner wire gives higher resistance and therefore the unit becomes inefficient faster at high speeds. 2.2.3.6 MAGNETIC CIRCUIT The lines of force from a magnet are said to originate at one pole and return to the other, just like a battery. 8

Air is a poor conductor, both for electricity and for magnetic lines of force. In order to make best use of a magnet in an alternator, we need to have the strongest possible magnetic field.

2.3 ROTOR
A wind generator gets its power from slowing down the wind. The blades slow it down, and the alternator collects the power. BOTH must be correctly designed to work together and do this efficiently.

2.3.1 DESIGN OF THE ROTOR

2.3.1.2 BLADE MATERIAL
Wood is really an ideal material for blades. It is very strong for its weight, easy to carve, inexpensive, and is resistant to fatigue cracking. Steel and aluminum blades are much too heavy and prone to fatigue cracking; sheet metal would be a poor choice, and extremely dangerous.

2.3.1.3 DIAMETER
Blades that are too short attached to a large alternator will not be able to get it moving fast enough to make good power. Blades that are too large for a small alternator will overpower and burn it up, or overspeed to the point of destruction in high winds--there's not enough of an alternator available to collect the energy coming in from the wind.

2.3.1.4 NUMBER OF BLADES The ideal wind generator has an infinite number of infinitely thin blades. In the real world, more blades give more torque, but slower speed, and most alternators need fairly good speed to cut in. 9

2 bladed designs are very fast

and easy to build, but can suffer from a

chattering phenomenon while yawing due to imbalanced forces on the blades. 3 bladed designs are very common and are usually a very good choice, but are harder to build than 2-bladed designs. Going to more than 3 blades results in many complications, such as material strength problems with very thin blades. Even one-bladed designs with a counterweight are possible.

2.3.1.5 TIP SPEED RATIO (TSR)

This number defines how much faster than the windspeed the tips of your blades are designed to travel. Your blades will perform best at this speed, but will actually work well over a range of speeds. The ideal tip speed ratio depends on rotor diameter, blade width, blade pitch, RPM needed by the alternator, and wind speed. Higher TSRs are better for alternators and generators that require high rpms--but the windspeed characteristics at your particular site will make a big difference also.

2.3.1.6 TAPER
Generally, wind generator blades are wider at the base and narrower at the tips, since the area swept by the inner portion of blades is relatively small. The taper also adds strength to the blade root where stress is highest, gives an added boost in startup from the wider root, and is slightly more efficient. The ideal taper can be calculated, and it varies depending on the number of blades and the tip speed ratio desired

2.3.1.7 PITCH AND TWIST

There are advantages to having a twist, though--like with taper, having more pitch at the blade root improves startup and efficiency, and less pitch at the tips improves high-speed performance. 10

The wind hits different parts of the moving blades leading edge at different angles, hence designing in some twist. One of our common blade designs that's right in the middle for design parameters is to build an even twist of 10 degrees at the root and 5 degrees at the tip,but the ideal solution will also depend on your alternator cut-in speed, efficiency and local wind patterns.

2.3.1.8 CARVING
Our layout and carving process is very simple,after marking the cut depth at the trailing edge at both the root and tip, the two depths are connected with a pencil line.

2.3.1.9 AIRFOIL
There are great lengths that you can go to for designing an airfoil. But all an airfoil needs to do is maximize lift and minimize drag. A power planer makes quick work of carving it, and a drawknife is great for carving too, especially with the deep cuts near the blade root.

2.3.1.10 BALANCING
The blades must be very well balanced to prevent vibration. This is more easily accomplished with a 2-blade rotor than a 3 bladed one. But generally, we simply use a homemade spring scale to make sure that each blade weighs exactly the same, and that each has the same center of balance. A simple balancing jig for any rotor configuration can be made with an upright spike that sticks into a dimple punched at the exact center of the hub.

11

2.4 FURLING AND SHUTDOWN SYSTEMS 2.4.1 FURLING SYSTEMS

A mechanism that turns the wind generator rotor at an angle out of the wind, either horizontally or vertically, to protect the machine from damage during high winds. A wind turbine that furls is also much more gentle on your tower and guy wires, the force on an overspeeding wind turbine increases as the wind gets stringer.. There are a variety of furling system designs

2.4.1.2

VARIABLE PITCH
An ideal but extremely complicated solution is to use blades which change pitch depending on the wind speed. These also have the advantage of keeping power output at the most efficient point for the current windspeed. During low winds, the blades are pitched for best startup. In higher winds, they rotate and adjust shaft speed to the ideal RPMs for the generator. In extreme winds, they turn the blades even further to protect the unit from damage. The problem is the complexity of making a system work reliably. Large commercial wind generators use this system exclusively, as do antique and modern Jacobs turbines, and some old Win Chargers

2.4.1.3

TILT-BACK
In these designs, the generator body is hinged just behind the nacelle.

When wind speed gets too high, the entire nacelle, hub and blade assembly tilts back out of the wind to nearly vertical. As the wind slows down, it returns to normal horizontal operating position by either springs, wind action on a tilted tail, or a counterweight. Commercial wind generators that use this method are the old Whisper models , the Wind stream, and many homemade designs. 12

2.4.1.4 FURLING TAIL

The generator is mounted off-center horizontally from the yaw bearing. The tail is also angled in this axis. The tail is also angled in the vertical axis, and hinged. When the wind force back on the rotor is strong enough to overcome the off-axis generator making it want to yaw and the angled tail trying to keep it from yawing, the tail folds up and turns the alternator away from the wind direction, forcing the wind turbine to yaw out of the wind. When wind speeds drops, the tail is returned to normal operating position by gravity, or springs. Many commercial and homemade designs (including ours) use this system, and it has proven to be very reliable.

2.4.1.5

FOLDING VANE
Similar to the furling tail, but the tail boom is fixed, with a hinged vane underneath. Used on some older Winchargers and homemade designs, the disadvantage is that tail and vane are more highly stressed from wind force during furling, as they still are sticking out there in the gale.

2.4.1.6

FLEXIBLE BLADES
The theory is that the blades flex both back toward the tower and around their main axis, and therefore protect themselves from over speeding. It does work if the materials and details are correct for example, the blades must not flex back far enough to hit the pole, and they must withstand flexing during cold weather too.

13

2.4.1.7 AIR BRAKES

Noisy and full of vibration, but they do work. Older Win Chargers used this system. Metal cups extend from the hub from centripetal force during high winds, and noisily slow the machine down; they retract back into the hub when the wind slows.

2.4.2 SHUTDOWN SYSTEMS

This is a manual control that completely shuts the wind generator down. It is not allowed to spin at all, and should be able to survive extremely violent winds in this condition. It can be electrical or mechanical.

2.4.2.1 ELECTRICAL SHUTDOWNWITH

Permanent magnet alternator a machine, simply shorting the main AC power output leads together should effectively shut down the wind turbine. The problem is that when the machine is spinning at high RPMs during a windstorm, the shutdown may be either impossible electrically, or too damaging to the alternator the heat produced in the stator coils by shutdown at high speeds turns the coils into molten slag.

2.4.2.2 MECHANICAL SHUTDOWN

These systems physically break the wind generator, or force it out of the wind by turning the tail parallel to the blades. Even the10kW wind turbine has a mechanical crank for emergency shutdown. Generally, a cable is attached to a hinged tail, with a small hand winch located at the bottom of the tower for the operator. 14

2.5 SLIP RINGS

The power produced by the generator must be transferred down the tower to your power system. Since the actual wind generator must yaw to keep pointed into the wind, the main power wires must be able to handle this. There are 2 options.

2.5.1 PENDANT CABLE

Our personal experience up here in Colorado is that it is much easier to simply use a length of flexible cable and a steel safety cable instead of slip rings. Use the highest quality stranded, flexible cable you can find and attach it in a loose loop from the wind generator power terminals to where your feed wire comes up the pole. Use a length of wire that allows about 3 or 4 wraps around the pole. Or, run the wire down the center of the tower pipe and let it twist inside. Our experience is that while the cord can eventually wind itself around the pole, it will also eventually unwind itself. Some of our models have flown for years with this kind of system and required no maintenance. With a properly designed wind turbine and furling system, you should hardly ever see the mill make a 360 degree yaw.

2.5.2 MAKE OR CONVERT SLIP RINGS

Slip rings can be salvaged from old car alternators and converted to wind generator use, or built from scratch using copper pipe, PVC pipe and graphite brushes. The need to use them and they make for another potential failure point, so we have not experimented with it.

15

AIM

CHAPTER 3 AIM
We are aiming to introduce the new contributions in the field of windmill and wind energy through design and fabricating the project.

17

PLAN OF WORK

CHAPTER 4 PLAN OF WORK

Planning is an important part of every project. Nobody plans to fail, but they fail to plan. So before staring our project work we made some planning for the successful completion of the project. 4.1 SELECTION OF PROJECT By considering the benefits of the project with the present conditions, the amount of money can be invested, availability of the material, duration of project, design and fabrication area the project can be planned. 4.2 DESIGN AND DRAWINGS Having been decided about the project to be manufactured, it must be designed. The work of the design should be done very carefully by considering all the relevant factors. After designing the project its detailed drawing are prepared so that no doubts are left for future, detailed specifications of raw materials and finished products should be decided carefully along with the specification of the machine required for their manufacture. 4.3 PURCHASE CONSIDERATION It is very difficult to fabricate each and every components of the project. Fabrication must be based on the accuracy that can obtained from the components. If the project have some electronic components, then it is better to buy the components from the market, and assemble it to the requirement.

19

4.4 FABRICATION Fabrication of the components can be done with the help of designed calculations and drawings through different manufacturing process like cutting, welding, drilling etc 4.5 ASSEMBLY OF THE PARTS The fabricated and purchased components are assembled together to complete the fabrication process. 4.6 COST ESTIMATION Cost estimation can be calculated by considering the material cost, labor cost, transportation charges etc.. 1. Material cost 2. Labour cost 3. Transportation expenses

4.7 REPORT At the end of the project work, a report is prepared for future references. The project report consists of all the items done during the project work.

20

DESIGN OF BELT DRIVE

Cross section of the belt drive[from PSG DB 7.58] cross sectional value=B Calculate the speed ratio i=n/N =400/250 i=16 I=D/d [from PSGDB 7.58]

d= 0.12mm i=D/d 16=D/0.12;D=1.92

Calculate the arc of contact [from PSGDB 7.54] =180-[(D-d)/c*60] c/d=1 C =1*1.92 =1.92 =180-[(1.92-0.12)/1.92*60] =56.25

Calculate the belt speed S=dn/(60*1000) =3.14*0.12*400/(60*1000) =2.5mm/sec

Find equivalent pitch diameter dc=dp*fb d=dp=0.12 fb=1.14 de=0.12*1.14 =0.136 21

Calculate the rating of belt [from PSGDB 7.62] B=(0.79S-0.09-50.8/de-1.32*10-4S2)S =(0.79*2.5-0.09-50.8/0.136-1.32*10-42.52)2.5 =5.82

Calculate the nominal pitch length[from PSGDB 7.61] L=2C+ 3.14/2(D+d)+[(D-d)2/4C] =2*1.92+ 3.14/2(1.92+0.12)+ [(1.92-0.12)2/4*1.92] =5.03

Calculate the design power =(P*Fa)/(Fd*Fc) Fa=(from psgdb 7.69) Fd=(from psg db 7.68) Fc= (from psgdb 7.59) Design power=(2.03*1)/(0.65*0.92) =3.3

Calculate the no of belt [from PSGDB 7.70] No of belt =(design power)/(rating of belt)

=3.3/0.58 =5.6 6. Calculate the new centre distance [from PSGDB 7.61] C=A+(A2-B) A=L/4-[(D+d)/8] =5.03/4-[(1.92+0.12)/8] =1.12 B=(D-d)2/8 =(1.92-0.12)2/8

22

=0.425 C=1.12+[(1.12)2-(0.425)] =2.03 SPECIFICATION *Cross section=B *Larger pulley diameter=1.92 *Smaller pulley diameter=0.12 *Centre distance C=1.92 *Width of the pulley=2 * No of belt=1

23

CHAPTER 6 ADVANTAGES OF WINDMILL

Environmental

Using wind power reduces carbon dioxide, along with other greenhouse gas emissions, which contributes to countermeasuring climate change.

Generating of electricity from wind does not require mining, drilling, nor transportation of any fuel. Therefore it saves limited resources of fossil fuels on Earth.

It does not contribute to any loss to water circulation in eco-systems. Wind power does not generate solid nor gaseous polluting waste (also the radioactive ones). The technology is free of risk such as reactor breakdowns. Social and economical

The cost of wind energy is stable, since it is not affected by fuel market price fluctuations. Building wind plants creates job opportunities and new workplaces* in the community. Furthermore, money for the investment is spent locally (procuring materials, servicing during construction and after the turbines are set). Thereupon, general economic growth of the region is being spurred.

Wind power investments tend to improve local infrastructure* like roads, power, transportation.

It clearly saves money by offsetting oil, gas fired generation or expensive power imports. The development of wind energy solutions encourages eco-tourism. It has a great impact on regional development and activation. 24

Wind power, comparing to other energy sources, provides the best guarantee of preserving natural rural landscape

Wind turbines occupy little amount of space and may easily coexist with agri- or horticulture. The operational costs of wind energy are relatively low. Wind energy contributes to diversification of energy sources and decreases dependence from energy or fuel imports which increases energy security of the country.

25

COST ESTIMATION

CHAPTER 7
COST ESTIMATION:

S.NO 1

COMPONENT MOTOR GENERATOR V-BELT FAN WHEEL WITH PEDAL PULLEYS

MATERIAL -

QUANTITY 1 1

COST 300 400 25 75 150

RUBBER PLASTIC STEEL

1 1 1

PLASTIC CAST IRON MERCURY CADMIUM -

2 1 1

50 150 150

9 10

STAND BATTERY

TOTAL

1300

27

CHAPTER 8 SUMMARY

By doing this project, we aim to produce an optimum output. When we get optimum output it will be cheaper than the conventional sources. Energy generated using the windmill is transmitted to the turbine with the help of belt drive and generated energy is stored in an external rechargeable battery. Wheel with pedal attached to the turbine is used to transmit water from one region to another region in a field. At the time of without wind, turbine is used to rotate with the help of energy stored in the battery.

28

CONCLUSION

CHAPTER 8 CONCLUSION
The design and fabrication of power generation and irrigation by windmill has been successfully introduced. By doing this project, our aim to produce get optimum output get fulfilled.

30

REFERENCE

http://en.wikipedia.org/wiki/Wind_power PSG data book, Author(s):PSG College of technology ,Coimbatore. http://www.thesolarguide.com/wind-power/turbine-parts.aspx Wind Energy Systems for Electric Power Generation: Green Energy and Technology Author(s):ManfredStiebler

31

CHAPTER 11 BIBLIOGRAPHY

FRONT VIEW:

32 TOPVIEW:

33