0% found this document useful (0 votes)
26 views7 pages

Engineering Graphics QB - LR - Compiled

Uploaded by

samyakkanekar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
26 views7 pages

Engineering Graphics QB - LR - Compiled

Uploaded by

samyakkanekar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Engineering Graphics and Design

Unit 1
1.A rectangular plot of land area 0.45 hectare, is represented on a map by a similar
rectangle of 5 square cm. Calculate R. F. Of the scale of the map. Also draw a
scale to read upto single meter from the map. The scale should be long enough to
measure upto 400 meters.

2. A car is running at a speed of 50 km/hour. Construct a diagonal scale to show 1


km by 3 cm and to 6 km. Mark also on the scale the distance covered by the car in
5 minutes 28 seconds.

3. An area of 144 sq. Cm on a map represent an area of 36 sq. Km on the field.


Find the R.F. of the scale and draw a diagonal scale to show kilometres,
hectometres and decametres and to measure upto 10 kilometres.

4. A 3.2 cm long line represents a length of 4 meters. Extend this line to measure
length upto 25 meters and show on it units of meter and 5 meters. Show the length
of 17 meters on this line.

5. The R.F. of a scale showing miles, furlong and chain 1/50688. Draw a scale to
read upto 5 miles and show on it, the length representing 3 mile 5 furlong 3 chains.

6. A room of 1728m3 volume is shown by a cube of 216m3 volume. Find R.F. and
construct a plain scale to measure upto 42m. Mark a distance of 22m on the scale.

7. Explain Dimensioning . Give various methods of Dimensioning.

8. Explain briefly about the conventional line types and their usage.

9. Explain Lettering with appropriate examples.

10. A cube of 5cm represents a tank of 8000cubic metre volume. Find the R.F and
construct a scale to measure upto 60m and mark a distance of 47m . Indicate R.F of
the scale.
Engineering Graphics and Design
Unit 2
1. What do you mean by principle of projection? Explain the different methods of
projection?

2. Draw the FV, TV and side views of the block shown.

3. Two points A and B are in the HP. The point A is 30 mm in front of the VP,
while B is behind the VP. The distance between their projectors is 75 mm and the
line joining their top views makes an angle of 45o with xy. Find the distance of the
point B from the VP.

4. Draw the isometric view of frustum of cone with base diameter 60mm, axis
80mm and top diameter 30mm.

5. A point P is15 mm above the HP and 20 mm in front of the VP. Another point Q
is 25 mm behind the VP and 40 mm below the HP. Draw projections of P and Q
keeping the distance between their projectors equal to 90mm. Draw straight lines
joining (i) their topviews and (ii) their front views.

6. Draw the isometric view of the following casting.

. .
7. The top view of a 75 mm long line measures 55 mm. The line is in the V.P., its
one end being 25 mm above the H.P. Draw its projections.

8. The front view of a line, inclined at 30 o to the V.P. is 65 mm long. Draw the
projections of the line, when it is parallel to and 40 mm above the H.P., its one end
being 30 mm in front of the V.P.

9. Differentiate between 1st angle projection and 3rd angle projection.

10. Draw the isometric view of a cylinder of base 40 mm diameter and axis 65 mm
long.
UNIT-3

1. Explain the importance of AutoCAD in Engineering Drawing?

2. Write Benefits and Limitations of CAD.

3. Explain Basic Co-ordinate system in CAD?

4. Explain SNAP, GRID, O-Snap, in autocad?

5. Explain the use of Polar and ortho status bar commands?

6. Explain the following commands with example:LAYER, LIMITS, UNITS?

7. Write any 6 names of CAD software.

8. What is CAD?

9. Explain how to set limit in AUTOCAD with example?

10. Write steps to prepare following drawing in AUTOCAD using:

i. Absolute cartesian coordinate system

ii. Relative coordinate system

iii. Polar coordinate system

Assume point A as staring point. Coordinate of A is (20,20).


UNIT-4

1. Explain Circle command with all 5 methods?

2. Explain Ellipse command in AUTOCAD?

3. Explain Rectangleand Polyline commands in AUTOCAD?

4. Explain TRIM, Move, Rotate and Copy in Editing tools?

5. Explain Mirror Offset, Chamfer and FILLET?

6. Explain following drawing tool commands with example:CIRCLE, ARC,


POLYGON, ELLIPSE?

7. Explain array and its types in 2D?

8. Explain the use of dimensioning? Explain different types of dimensions used


in AUTOCAD.

9. Explain the 2 methods for drawing regular polygon in AUTOCAD?

10. Explain the methods for creating arc in AUTOCAD with example?
UNIT-5

1. Explain solid modeling

2. Explain wire frame modeling.

3. Explain Surface modeling.

4. Explain following commands in Autocad:

a) Extrude

b) Revolve

c) sweep

d) Loft

e) Wedge

5. Explain Shell, Round, Taper faces, copy Faces and Chamfer edges?

6. Explain modifying tools: 3D-move, 3D-copy, Rotate and scale?

7. Explain Array and its Types?

8. Explain three types of 3D dimensional models in AUTOCAD.

9. Explain following commands (solid editing tool commands):Copy faces,


Chamfer edges, Shell, Round?

10. Explain the advantages of surface modeling over solid modeling?

You might also like