Scribd Logo
Upload

Welcome to Scribd!

  • 0 views

    MSA5T1006A297866

    Uploaded by

    n810e

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MSA5T1006A297866

    Uploaded by

    n810e
    0 views5 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    0 views5 pages

    MSA5T1006A297866

    Uploaded by

    n810e

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 5

    Headlight Assembly

    LIGHTING SYSTEM

    13.Headlight Assembly
    A: REMOVAL
    CAUTION:
    Do not perform work with wet hands.
    1) Disconnect the ground cable from battery.
    2) Remove the clips and remove the air intake duct. (When removing the headlight RH).

    LI-01074

    3) Remove the front bumper face assembly. <Ref. to EI-39, REMOVAL, Front Bumper.>
    4) Remove the fender cover assembly UPR.
    (1) Remove the clip.
    (2) Release the claws of the fender cover assembly UPR by pulling it forward and remove the fender cov-
    er.

    LI-00981

    5) Remove the headlight assembly.

    LI-26
    Headlight Assembly
    LIGHTING SYSTEM

    (1) Remove the bolts and clips, and pull out the headlight assembly to the front of the vehicle.

    LI-01071

    (2) Disconnect the connector and remove the headlight assembly.


    • Headlight connector RH

    LI-01082

    LI-27
    Headlight Assembly
    LIGHTING SYSTEM

    • Headlight connector LH

    LI-01081

    B: INSTALLATION
    Install each part in the reverse order of removal.
    Tightening torque:
    Headlight ASSY: 7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
    C: ADJUSTMENT
    1. HEADLIGHT BEAM ADJUSTMENT
    CAUTION:
    Turn off the light before adjusting the headlight beam level. If it is necessary to inspect the beam lev-
    el, do not keep the light on for two minutes or more.
    1) Before checking the headlight beam level, be sure of the following:
    • the area around the headlight has not sustained any scratches, damage or other type of deformation.
    • Vehicle is parked on a level surface.
    • The inflation pressure of tires is correct.
    • Vehicle’s fuel tank is fully filled.
    2) For vehicle with a manual leveler, set the headlight beam leveler switch to the “0” position.
    3) Bounce the vehicle several times to normalize the suspension.
    4) Make certain that someone is seated in the driver’s seat.

    LI-28
    Headlight Assembly
    LIGHTING SYSTEM

    5) Measure the distance between the low beam bulb centers, and the height of the bulb center.

    (B)
    (A)

    LI-01092

    (A) High beam (B) Low beam

    6) Place the vehicle with the front end facing to the measurement panel.

    (A)
    W1 W2
    W2

    W
    W W1
    (D)
    (A)
    h h (B)

    (D)

    (C)

    LI-01077

    (A) Vehicle center (C) 3 m (10 ft) (D) Height of headlight center
    (B) Bulb center marking

    W mm (in) h mm (in) at 3 m (10 ft)


    1,404 (55.28) 21 (0.83)

    LI-29
    Headlight Assembly
    LIGHTING SYSTEM

    7) Adjust the headlight low beam by turning the aiming screw.

    LI-01093

    NOTE:
    When using a tester, follow the instructions of the tester manual.

    LI-30

    You might also like