(PMI) Programmable Module Installation

This information is
constantly updated,
the latest version can
be found on PTS.
ABS/ CSM/ DATC/ DDM/ FEM/ RASM RCM/ RESCU/
No PMI PCM ACM CTM DSM EPB HEC/ ICM LCM LTM MCM NAV OTC REM SCLM TPMS VAPS 4x4CM
RABS RAP EATC RKE GEM VDM ECS VEMS
Aviator Type 2 03 03 03 03 03 03 03 03 03

Blackwood Type 1 02-03 02-03

Continental Type 1 99 99-02

Contour/Mystique X Type 1

Cougar X Type 1
Crown Victoria/
Type 1 00-03 00-03 03 03
Grand Marquis
Econoline X Type 1

Escape Type 1 01-03 01-03

Escort/Tracer X Type 1
99-02
Excursion Type 1 00-03 02-03 00-01 02-03 02-03
03
Expedition/ 99-01 03 EXP
Type 2 03 03 99-02 03 03 NAV 03 NAV 03 03
Navigator 01-03 99-03 NAV
Explorer/ 99-02 00-03
02-03 Type 2 02-03 02.5-03 02.5-03 99-01 02-03 03
Mountaineer 02.5-03 "N" Tow
Explorer Sport/ Before 03
Type 1
Sport Trac 7-24-00 "N" Tow
99-01 99
F-Series (150) Type 1
01-03 00-03
F-Series Super Type 1 99-01
99-03 02-03 00-01 02-03 99-03
Duty 250 - 550 03 6.0 DI Type 3 02-03
view online
F650/F750 Type 1 service man
00-02
Type 1 IVD must be
Focus 00-01 02-03.5 00-03.5 00-03.5
03 PVEZ Type 3 "Calibrated"
00-02 Type 1 00-02
LS 00-03 00-03 00-03 00-03 03 00-03 00-03 00-03 03 00-03 00-02
03 Type 3 03
Marauder Type 1 03 03

Mustang Type 1 00-03

99-00
Ranger Type 1 99-00 w/ABS
w/RABS
Taurus/Sable Type 1 99-03
02 Type 2
Thunderbird 02-03 02-03 02-03 02-03 02-03 02-03
03 Type 3
00
Town Car Type 1 99-03 03 99-03 00-03 99-03 03 02-03
01-03
Villager X Type 1

Windstar Type 1 99-03 99-03 99-03 99-03 99-03 99-03

PCM Types - Verify latest calibration after installing PCM If using NGS - Select Service Bay Functions - (Select Module) - Select applicable feature.
Type 1 Bolt In - May require tire size, and axle ratio to be entered. If using WDS - Select applicable feature within Module Programming.
Type 2 Requires PMI - Requires using Flash Cable (NGS only). Module does NOT use AS BUILT data. PMI can be used to inhale and exhale customer preferences when replacing module.
* When using WDS, if "Hardware Level Conflict" message is displayed If using NGS, use UBP Cable. If original module is not available, use "Customer Preference Item" menu on NGS to configure features.
after replacing PCM, delete current sessions, start new session, re- If using WDS, and original module is not available, select PMI and answer questions when prompted.
perform PMI, answer questions accordingly. Module uses AS BUILT data and PMI must be performed when module is replaced. Use UBP Cable(NGS only).
Type 3 CAN Network - requires WDS or NGS+ If original module is not available then AS BUILT data must be entered to correctly configure module. FCS - 13822 - 03
Note: WDS may ask questions instead of prompting for AS BUILT. REV. 28-Apr-03
 (PMI) Programmable Module Installation
This information is
constantly updated,
the latest version can
be found on PTS.

Accessing AS BUILT Data Acronyms BCE Module Addresses PMI using NGS PMI using WDS
To be used when original BCE module is NOT available To be used when original BCE module is NOT available
1. Log on to WWW.FMCDEALER.COM ABS Antilock Braking System A0-01 DDM/RKE
2. If logged in as a technician, select "Service Publications" ACM Audio Control Module A2-01 DSM 1. Install new module. 1. Install the new module first.
under TOP SPOTS. OR if logged in as a service CSM Central Security Module AF-01 LTM 2. Using NGS with latest version green card select "Programmable 2. Connect the WDS and ID the vehicle as normal.
manager, select "Service Publications" under VEHICLE CTM Central Timer Module C1-01 CSM Module Installation". 3. From the Toolbox icon, select and highlight "Module
SERVICE. DATC Dual Automatic Temperature Control C3-01 SCLM 3. Select which module is being replaced and press trigger (FEM is Programming" and press check mark from the toolbox menu.
3. Click on "Service Publications" again. DDM Driver Door Module DA-01 TPMS referred to as GEM). 4. Select and highlight "Programmable Module Installation" and
4. Click on "As Built" DSM Driver Seat Module 19-01 4x4CM 4. Follow on screen Instructions. then highlight module that was replaced and press check mark.
5. Click on "Call As Built" EATC Electronic Automatic Temperature Control 2A-01 EPB 5. Select "Retrieve Module Config – Old ECU" and press trigger. 5. Follow on screen instructions and turn ignition switch to OFF
6. Enter the vehicle VIN number in the box and click on ECS Electronic Crash Sensor 20-01 VDM/RASM 6. Follow on screen instructions. and press check mark.
SUBMIT at the bottom. EPB Electronic Park Brake 28-01 ABS 7. NGS will attempt to retrieve module data from the PCM 6. The WDS will retrieve the module data from the PCM and
7. The " Module Reprogramming" page will open with the FEM Front Electronic Module 30-01 VAPS a. If module data is available proceed to step A. automatically download it into the new module and display
"VIN" and "Vehicle Data" at the top. GEM Generic Electronic Module 48-01 RAP b. If NGS displays "Call As Built Data Center" proceed to "Operation Successful – Programming Complete".
8. Below this are two columns, the one on the left is PCM HEC Hybrid Electronic Cluster 50-01 REM step B. 7. IF the data is not available in the PCM, the WDS will display a
DATA and the one on the right is BCE DATA. ICM Instrument Cluster Module 52-01 GEM or FEM or CTM screen stating to contact the As Built data center. Retrieve data
9. Only programmable modules available in that vehicle LCM Lighting Control Module 58-01 RCM or ECS STEP A from WWW.FMCDEALER.COM at this time and press check
will be listed under BCE Modules. LTM Liftgate Module 6A-01 OTC 1. At menu select " Restore Configuration – New ECU" and press mark.
10. Some modules may have more than one line of data. MCM Message Center Module 60-01 ICM Or HEC trigger. 8. Enter the module data (module address and line are displayed to
11. If a module is not listed, then it is not a programmable NAV Navigation Module 68-01 NAV 2. NGS will complete loading retrieved data into the module and the left of the three entry boxes) and press check mark.
module. OTC Overhead Trip Computer 61-01 MCM display "Module Download Successful". 9. WDS will now download the data into the new module and
12. If As Built data is not available then Ford Technical RAP Remote Anti-Theft Personality 70-01 LCM 3. Verify proper operation. display "Operation Successful – Programming Complete".
Hotline must be contacted. RASM Rear Air Suspension Module 80-01 ACM 10. Verify proper operation.
RCM Restraint Control Module 90-01 RESCU or VEMS STEP B
*** The NGS and WDS refer to the FEM as a GEM module. REM Rear Electronic Module 98-01 DATC or EATC 1. If NGS displays "Call As Built Data Center" – press trigger.
RESCU Remote Emergency Satellite Cellular 2. NGS may ask for VEHICLE DATA – enter vehicle data and
RKE Remote Keyless Entry press store. PMI using WDS
SCLM Steering Column Lock Module 3. NGS will ask for module data line 01 – enter data and press To be used when original BCE module is available
TPMS Tire Pressure Monitoring System store.
VAPS Variable Assist Power Steering 4. NGS will then ask if there is an additional line of data available 1. Connect WDS and ID the vehicle as normal.
VEMS Vehicle Emergency Messaging System for that address – select YES or NO depending on info in As 2. Select and highlight "Module Programming" and press check
VDM Vehicle Dynamics Module Built Data sheet. (See sample data) mark from the toolbox menu.
4x4CM 4x4 Control Module 5. Repeat steps 3 and 4 until you answer NO for step 4. 3. Select and highlight "Programmable Module Installation".
6. NGS should then show a screen stating that module data was 4. Follow on screen instructions and turn ignition switch to OFF
stored – press trigger. and press check mark.
7. Follow on screen instructions. 5. Replace module and press check mark.
8. Select "Restore Module Config – New ECU" and press trigger. 6. Follow on screen instructions and turn ignition switch to ON and
9. NGS will complete downloading data just entered into the press check mark.
module and display a message "Module Data Download 7. Module configuration is complete.
Successful". 8. Verify proper operation.
10. Verify proper operation.

PMI using NGS

To be used when original BCE module is available

1. Using NGS with latest version green card select "Programmable

Module Installation".
2. Select which module is being replaced and press trigger (FEM is
referred to as GEM).
3. Follow on screen Instructions.
4. Select "Retrieve Module Config – Old ECU" and press trigger.
5. Follow on screen instructions.
6. At menu select " Restore Configuration – New ECU" and press
trigger.
7. Follow on screen instructions.
8. NGS should display "Module Download Successful".
9. Verify proper operation.
FCS - 13822 - 03
REV. 28-Apr-03
 How does PMI work with NGS?
1. When "Retrieve Config Old ECU" is selected
The NGS will first attempt to read the VIN from the PCM VID block. If the VIN cannot be read, the NGS will
ask the user to enter the VIN using the Scroll and Trigger button.

It will then perform Self Test on the selected module to determine if the module has been previously
configured. It does this by checking for the presence of DTC B2477.
If DTC B2477 is NOT detected. The NGS will "Inhale", or read the data from the module and store it so that it
can be "Exhaled" or downloaded into the new module. NGS will state that module data has been stored.
Return to the main menu and select Restore Config New Ecu.

If DTC B2477 is detected during Self Test, the NGS display will read "This Module Has Not Been Configured.
Reinstall the Original Module to Retrieve Configurable Data. If the Old Module is Not Available, Continue for
Backup Data."
When the Trigger button is pressed after this screen is displayed, the NGS will attempt to retrieve the selected
module's backup data from the PCM if available (Not all vehicles contain BCE module backup data in the PCM).
If NGS as able to retrieve the module's backup data from the PCM, NGS will state that module data has been
stored. Return to the main menu and select Restore Config New Ecu.

If the NGS is NOT able to retrieve the module's backup data from the PCM, it will state to contact the As-Built
Data Center. When entering As-Built data to configure the module, the NGS will require that the Vehicle Data
located under the VIN number on the vehicles As-Built Data page be entered. The Vehicle Data is used by the
NGS to verify that the As-Built page being used to configure the selected module is actually for the vehicle
VIN as recognized by NGS, either as entered by the technician or read from the PCM during the first step.
After the NGS verifies the Vehicle Data that was entered matches the VIN that was stored, it will then ask that
the selected module's data be entered from the As-Built Data page. After all the selected module's data has been
entered, NGS will state that module data has been stored. Return to the main menu and select Restore Config
New Ecu.

2. When "Restore Config New ECU" is selected

The NGS will retrieve the selected module's data from an internal NGS memory location as it was either
"Inhaled" from the original module, retrieved from the PCM, or manually entered by the Technician.
It will then download the configuration data into the new module.
After the data has been downloaded from the NGS to the module, the NGS will read the configuration data back
from the module and compare it the data that was stored in the internal NGS memory location.
If the data read from the module matches the data stored in NGS, the NGS will state Configuration Complete.