2

ELECTROMAGNETIC SPECTRUM
4

frequency refers to the number of full wavelengths that pass by a given point in
space every second; the SI unit for frequency is Hertz (Hz)

Wavelength and frequency are inversely proportional: that is, the shorter the wavelength,
the higher the frequency, and vice versa. This relationship is given by the following equation:

Their product is the constant c, the speed of light, which is equal to 3.00×108 m/s
This relationship reflects an important fact: all electromagnetic radiation, regardless of
wavelength or frequency, travels at the speed of light.

A is the length of time it takes for one wavelength to pass by a given point in

ELECTROMAGNETIC SPECTRUM
5

Planck found that the electromagnetic radiation emitted by blackbodies could not
be explained by classical physics, which postulated that matter could absorb or
emit any quantity of electromagnetic radiation.
Planck observed that matter actually absorbed or emitted energy only in whole-
number multiples of the value , where h ×10 34 J/s
and is the frequency of the light absorbed or emitted

When an atom or molecule loses energy, it emits a photon that carries an energy
exactly equal to the loss in energy of the atom or molecule. This change in energy
is directly proportional to the frequency of photon emitted or absorbed. This
relationship is given by
 ELECTROMAGNETIC SPECTRUM
6

Different Types Of Electromagnetic Waves

ELECTROMAGNETIC SPECTRUM
7

EM waves Characterisitcs:
The higher the frequency, the more energy the wave has.
Do not require media in which to travel or move.
considered to be transverse waves because they are made of vibrating electric
and magnetic fields at right angles to each other, and to the direction the waves
are traveling.
Inverse relationship between wave size and frequency: as wavelengths get
smaller, frequencies get higher.
 RADAR
8

Radar is a contraction of the words Radio Detection And Ranging.

Radar is an electromagnetic system for the detection and location of objects. It

operates by transmitting a particular type of waveform, a pulse-modulated
sine wave for example, and detects the nature of the echo signal.

Radar can see through conditions such as darkness, haze, fog, rain, and snow
which is not possible for human vision. In addition, radar has the advantage
that it can measure the distance or range to the object.

RADAR
9

How does radar work?

1. Magnetron generates high-frequency radio
waves.
2. Duplexer switches magnetron through to antenna.
3. Antenna acts as transmitter, sending narrow
beam of radio waves through the air.
4. Radio waves hit enemy airplane and reflect
back.
5. Antenna picks up reflected waves during a break
between transmissions. Note that the same
antenna acts as both transmitter and receiver,
alternately sending out radio waves and
receiving them.
6. Duplexer switches antenna through to receiver
unit.
7. Computer in receiver unit processes reflected
waves and draws them on a TV screen.
8. Enemy plane shows up on TV radar display with
any other nearby targets
 RADAR
10
Doppler Effect in Radar Systems.
If the target is not stationary, then there will be a
change in the frequency of the signal that is
transmitted from the Radar and that is received by
the Radar. This effect is known as the Doppler
effect.(frequency shift)
According to the Doppler effect, two possible cases
The frequency of the received signal will increase,
when the target moves towards direction of Radar.
The frequency of the received signal will decrease,
when the target moves away from the Radar.

Use of principle:
A stationary transmitter shoots waves at a moving
object. The waves hit the object and bounce back. The
transmitter (now a receiver) detects the frequency of
the returned waves. Based on the amount of the
Doppler shift, the speed of the object can be
determined.

RADAR
11
An elementary form of radar consists of a transmitting antenna emitting
electromagnetic radiation generated by an oscillator of some sort, a receiving antenna,
and a signal receiver.
A portion of the transmitted signal is intercepted by a reflecting object (target) and is
reradiated in all directions.
The receiving antenna collects the returned signal and delivers it to a receiver, where it
is processed to detect presence of target and to extract its location and relative velocity.
The distance to the target is determined by measuring the time taken for the Radar
signal to travel to the target and back.
The direction, or angular position, of the target is determined from the direction of
arrival of the reflected wave front.
The usual method of measuring the direction of arrival is with narrow antenna beams.
If relative motion exists between target and radar, the shift in the carrier frequency of
the reflected wave (Doppler Effect) is a measure of the target's relative (radial) velocity
and may be used to distinguish moving targets from stationary objects.
In radars which continuously track the movement of a target, a continuous indication
of the rate of change of target position is also available
 RADAR
12

It was first developed as a detection device to warn the approach of hostile aircraft
and for directing antiaircraft weapons. A well designed modern radar can extract
more information from the target signal than merely range.

Measurement of Range:
The most common radar waveform is a train of narrow, rectangular-shape pulses
modulating a sine wave carrier.

The distance, or range, to the target is determined by measuring the time TR taken by
the pulse to travel to the target and return.
Since electromagnetic energy propagates at the speed of light c (3 x 108 m/s) the
range R is given by : R= cTR /2 The factor 2 appears in the denominator because of
the two-way propagation of radar.
With the range R in kilometers or nautical miles, and TR in microseconds, the above
relation becomes: R(km) = 0.15 X TR ( µS )

RADAR
13

Maximum unambiguous range:

Once the transmitter pulse is emitted by the radar, sufficient time must elapse to
allow any echo signals to return and be detected before the next pulse is
transmitted.
Therefore, the rate at which the pulses may be transmitted is determined by the
longest range at which targets are expected. If the pulse repetition frequency is too
high, echo signals from some targets might arrive after the transmission of the next
pulse, and ambiguities in measuring range might result

The range beyond which targets appear as second-time-around echoes (or the
farthest target range that can be detected by a Radar without ambiguity) is called
the maximum unambiguous range and is given by: R unambig. = C/2fp
Where fp = pulse repetition frequency, in Hz. (PRF)
 RADAR
14

Simple form of Radar Equation:

If the power of the radar transmitter is denoted by Pt and if an isotropic antenna is used
(one which radiates uniformly in all directions) the power density (watts per unit area) at
a distance R from the radar is equal to the transmitter power divided by the surface area
re of radius R with radar at its centre.

The gain G of an antenna is a measure of the increased power radiated in the direction
of the target as compared with the power that would have been radiated from an
isotropic antenna. It may be defined as the ratio of the maximum radiation intensity from
the given antenna to the radiation intensity from a lossless, isotropic antenna with the same
power input.

The radar cross section has units of area. It is a characteristic of the particular target
and is a measure of its size as seen by the radar. The radar antenna captures a portion
of the echo power. If the effective area of the receiving antenna is denoted as Ae , then
the power Pr .received by the radar is given by

RADAR
15

The maximum radar range Rmax is the distance beyond which the target cannot
be detected. It occurs when the received echo signal power Pr just equals the
minimum detectable signal Smin.
The important antenna parameters are the transmitting gain and the receiving effective
area
Radar frequencies:
Conventional radars are
operated at frequencies
extending from about 220 MHz
to 35 GHz, a spread of more
than seven octaves. These are
not necessarily the limits, since
radars can be, and have been,
operated at frequencies outside
either end of this range.
The place of radar frequencies
in the electromagnetic spectrum
is shown in the figure
 RADAR
16

Letter code designation of Radar frequencies:

Early in the development of radar, a letter code
such as S, X, L, etc., was employed to designate
Radar frequency bands.

military secrecy, the designations were

maintained, probably out of habit as well as
the need for some convenient short
nomenclature.

This usage has continued and is now an

accepted practice of radar engineers. The table
below lists the radar-frequency letter-band
nomenclature adopted by the IEEE

RADAR
17

Applications of Radar:
1. Military Use: Initial and important user of Radar
(i)Early warning of intruding enemy aircraft & missiles (ii)Tracking hostile targets and
providing location information to Air Defense systems consisting of Tracking Radars
controlling guns and missiles. (iii)Battle field surveillance (iv)Information Friend or Foe IFF
(v)Navigation of ships, aircraft, helicopter etc.

2. Civilian Use:
(i)Air Traffic Control (ATC) All airports are equipped with ATC Radars, for safe landing
and take-off and guiding of aircraft in bad weather and poor visibility conditions.
(ii)Aircraft Navigation (a) All aircrafts fitted with weather avoidance radars. These Radars
give warning information to pilot about storms, snow precipitation etc. lying ahead of

helicopter.

(i)Radar used to avoid collision of ships during

poor visibility conditions (storms, cyclones etc.) (ii)Guide ships into seaports safely.

4. Meteorological Radar: Used for weather warnings and forecasting.

18
20
22

-9
 EDM EQUIPMENT
24

Classification of EDMI
EDMI can be classified on the basis of three parameters
(Schoffield, 2001; Kavanagh, 2003)
:(i) wavelength used
(ii) working range
(iii) achievable accuracy

(i) Classification on the basis of wavelength

Present generation EDMIs use the following types of wavelengths (Schoffield, 2001):
(a) infrared
(b) laser
(c) microwaves

The first two types of systems are also known as electro-optical whereas the third category is
also called the electronic system.

EDM EQUIPMENT
25
Electro-optical Systems
Infrared: Systems employing these frequencies allow use of optical corner
reflectors (special type of reflectors to return the signal, explained later) but need
optically clear path between two stations. These systems use transmitter at one end of
line and a reflecting prism or target at the other end.

Laser: These systems also use transmitter at one end of line and may or may not use a
reflecting prism or target at the other end. However, the reflectorless laser instruments
are used for short distances (100 m to 350 m). These use light reflected off the feature
to be measured (say a wall).

Electronic System
Microwave
These systems have receiver/transmitter at both ends of measured line. Microwave
instruments are often used for hydrographic surveys normally up to 100 km.
These can be used in adverse weather conditions (such as fog and rain) unlike infrared
and laser systems. However, uncertainties caused by varying humidity over measurement
length may result in lower accuracy and prevent a more reliable estimate of probable
accuracy.
26

g
28
30
 EDM EQUIPMENT
32

iii) Signal transmitter and receiver

For long waves the most efficient radiator is a straight vertical wire of effective length /4
operating as one half of a dipole. In case of microwave, the signals can be radiated by
dipoles of the appropriate dimensions. For visible spectrum wavelength, high degree of
collimation is achieved making use of optical lens system.

(iv) Beam splitter

It divides the light emitted from the diode into two signals: an external measurement beam
and an internal reference beam. By means of telescope mounted on EDMI, the external
beam is targeted to a retro-reflector

(v) Reflector
Reflectors are required to return the signal to the point of comparison (at the master
station) and have different requirements

EDM EQUIPMENT
33

vi) Filter
The internal beam passes through a variable-density filter and is reduced in intensity to
a level equal to that of the returned external signal which enables a more accurate
measurement. Both internal and external signals pass through an interference filter,
which eliminates undesirable energy.

(vii) Amplifier
These filtered signals are converted to electrical energy while maintaining the phase-
difference. These signal are weak and are amplified by an amplifier.

(viii) Phase discriminator

Phase discrimination is carried out by this component. A phase meter converts the phase
difference into direct current with magnitude proportional to the differential phase
which is subsequently displayed as the distance measured.

(ix) Display unit

The display unit provides results of range measurement on LCD panel.
 EDM EQUIPMENT
34

Operations with EDMI

Measurement with EDMI involves four basic steps:

Setting up:
The instrument is centered over a station by means of tribrach or by mounting over a
compatible theodolite. Reflector prisms are set over the remote station either on tribrach or
on a prism pole. Observations related to height or instrument and prism are recorded. These
are usually kept the same to avoid any additional corrections.
Aiming:
The instrument is aimed at prisms by using sighting devices or theodolite telescope. Slow
motion screws are used to intersect the prism centre. Some kind of electronic sound or
beeping signal helps the user to indicate the status of centering.
Measurement:
The operator presses the measure button to record the slope distance which is displayed on
LCD panel.
Recording:
The information on LCD panel can be recored manually or automatically. All meteorological
parameters are also recorded.

ERRORS & CORRECTIONS IN EDM

35

Error sources in EDMI

(Kennie and Petrie, 1990):

(i) Instrument operation errors

One has to be careful for precise centering at the master and slave station
pointing/sighting of reflector entry of correct values of prevailing atmospheric conditions

(ii) Atmospheric errors

Meteorological conditions (temperature, pressure, humidity, etc.) have to be taken into
account. These errors can be removed by applying an appropriate atmospheric correction
model that takes care of different meteorological parameters from the standard (nominal)
one.

(iii) Instrument error:

Consists of three components - scale error, zero error and cyclic error. These are systematic
in nature.
36

0
1
2
3
 ERRORS & CORRECTIONS IN EDM
38

It consists of two components. The first component arises from the fact that the physical
center of the instrument which is plumbed over the survey station does not coincide with the
position within the instrument to which measurements are made.

The second component has similar interpretation for reflector which absorbs changes in
velocity of light while moving from air to reflector glass prism and light path itself through
the reflector.

Cyclic error (K3): Also termed period errors, resolver errors or non-linearity errors and
varies with distance. These errors are caused by internal electronic contamination between
transmitter and receiver circuitry. Their effect is minimized by the manufacturer by electrical
isolation and shielding of instrument components.

2. Velocity correction
It is applied to account for atmospheric effects since:
1. signal is not traveling in vacuum but some medium which reduces the speed of EMR.
2. waves follow a curved rather than a straight line path between the transmitter and
receiver.

ERRORS & CORRECTIONS IN EDM

39

Propagating EM waves (at low or high frequencies) other than direct wave are results of
reflection, refraction, or diffraction of the wave caused by variations in the refractive index
(RI) of the atmosphere (n).
The RI is given as:

V is less than V0 depending upon n of medium (standard V0 = 299792458 ± 1.2 m/s as

accepted at XVIth General Assembly of the International Union of Geodesy and Geophysics
in 1975).

Two types of velocity corrections known as the first and second velocity corrections
(i) The first velocity correction:
Let the distance measured by EDMI be D after applying calibration often referred as
the instrument distance. The corrected distance D1 is given as D1 = D / ng The first
velocity correction is given as
40
 DIGITAL THEODOLITE
42

Electronic Theodolite

Theodolites or transits are used to measure

horizontal angles. These have evolved as follows:
Vernier theodolite (open face and Vernier
equipped instruments)
Optical theodolite (enclosed with optical
readouts with direct digital readouts or
micrometer equipped readouts)
Electronic theodolites (enclosed with
electronic readouts)

Electronic theodolites operate like any optical

theodolite with one major difference that these
instruments have only one motion (upper) and hence
have only one horizontal clamp and slow motion
screws.

DIGITAL THEODOLITE
43

Characteristics of electronic theodolites

Angle least count can be 1" with precision ranging from 0.5" to 20"
Digital readouts eliminate the personal error associated with reading and interpolation
of scale and micrometer settings.
Display window/unit for horizontal and vertical angles available at either one or both
ends.
Some digital theodolites have modular arrangement where they can be upgraded to be
a total station or have an EDMI attached for distance measurements.
Vertical circles can be set to zero for horizon or zenith along with the status of battery
shown in the display window.

Typical specifications for digital theodolites are generally given as follows:

Magnification: 26X to 30X
Field of view (FOV) 1.50.
Shortest viewing distance 1.0 m
Angle readouts, direct 5" to 20"
Level sensitivity: plate level vial 40"/2 mm, circular level vial 10"/2 mm
)
 DIGITAL THEODOLITE
44
An example :specifications for Nikon electronic theodolite (NE-
202/203):
Digital angle display is user-switchable from 5"/10" to 1"/5"
Built-in vertical axis compensator automatically compensates for
instrument inclination within ± 3' (NE-203)
Accuracy is 5" in 5" display mode.
Large, dot-matrix dual-line LCD screen displays both vertical
and horizontal angles simultaneously.
LCD screen and keyboard are placed on both sides of the
alidade for easier operation
Telescope magnification of 30X with a 45 mm objective
aperture diameter.
Employs a unique linear focusing mechanism to simplify focusing
at both short and long distances. Minimum focusing distance of
0.7 m.
Repeat horizontal angle measurement possible up to
±1999°59'55"
Continuous operation for up to 48 hours with fresh alkaline- Figure : Sokkia Electronic theodolite
manganese batteries (NE-202)

TOTAL STATION
45

Total Station (TS) can record horizontal and vertical angles together with slope distance
and can be considered as combined EDM plus electronic theodolite.

The microprocessor in TS can perform various mathematical operations such as averaging,

multiple angle and distance measurements, horizontal and vertical distances, X, Y, Z
coordinates, distance between observed points and corrections for atmospheric and
instrumental corrections.

Due to the versatility and the lower cost of electronic components, future field instruments
will be more like total stations that measure angle and distance simultaneously having:
all capabilities of theodolites
electronic recording of horizontal and vertical angles
storage capabilities of all relevant measurements (spatial and non-spatial
attribute data) for manipulation with computer.

Nowadays can be used in an integrated manner with Global Positioning System (GPS).
 TOTAL STATION
46

Example of Total Station

TOTAL STATION
47
Generally following types of total stations are available in the market:

Mechanical/manual TS:
The conventional multipurpose manual TS are used for routine works with powerful built-in
applications program and are cheaper

Motorized TS:
Equipped with servo to allow for fast, smooth and accurate aiming. This increases the productivity
by about 30%. The servo technology enables automated measurement.

Autolock TS:
In this case the instrument searches for an active remote positioning target (RMT), locks to it and
follows the target as it moves to different points. Autolock technology eliminates the need for time-
consuming error prone focusing and work effectively in low visibility environment. It improves the
time efficiency by up to 50%.

Automatic/Robotic TS:
In this TS, the control unit can be taken to the prism to record measurements and collect other data.
Generally a radio communication is used between TS and the prism.
 TOTAL STATION
48

The control unit, battery, antenna and radio modem are integrated to allow full control over
instrument and its operation. The prism used may be omni-directional .It improves the time
efficiency by up to 80%.

A typical TS has the following characteristics:

Graphic display:
All commands for survey operation as well as results are displayed on graphic LCD using
alphanumeric keyboard. Using built in software with menu and edit facilities, they automatically
reduce angular and linear observations to three dimensional coordinates of the vector observed

Dual axis compensation :

The dual axis tilt sensor monitors any inclination of the standing axis in both X- and Y-
directions. Consequently horizontal and vertical angle readings are free from error due to any
deviation of the standing axis from the perpendicular

Levelling and centering:

Electronic display for levelling operation enabling rapid and precise leveling. The electronic
levelling also eliminates errors caused by direct sunlight on plate bubbles.

TOTAL STATION
49

Laser plummet are replacing the optical plummet. A clearly visible laser dot is projected on
to the ground that helps in quick centering of the instrument

Storage :
Most TS have on-board storage of records using PCMCIA memory cards of different
capacity. The card memory unit can be connected to any external computer or to a special
card reader for data transfer

Friction clutch and endless drive:

This eliminates the need for horizontal and vertical circle clamps plus the problem of running
out of thread on slow motion screws.

Guide light or Lumi-guide tracking light :

This arrangement is fitted above the telescope objective lens and enables the target
operator to maintain alignment when setting-out points. This system emits two visible beams
of coherent red light, one steady and one blinking, enabling the rodman to locate the
correct line quickly and easily by finding the position where both are visible

.
 TOTAL STATION
50

Measurement modes :
Variety of measurement modes are available with TS such as precise, accurate,
and fast tracking, etc. Depending up on accuracy levels required and measurement
times, the surveyor can choose an appropriate measurement mode

Automatic target recognition (ATR):

This facility ensures that the instrument will lock on to the active target (by using
RMT: remote measurement target).

Reflectorless or direct reflex measurement:

Distance measurement without prism is also available on many instruments, typically
using two different coaxial red laser systems.

Remote control systems :

This arrangement allows truly one-person surveying capability. It is particularly
useful for mass point surveys, cadastral surveys, staking out and machine guidance.
Control of operation is transferred to the surveyor at the survey point where all
functions can be called up

TOTAL STATION
51

Field techniques with TS:

Various field operations in TS are in the form of wide variety of programs integrated
with microprocessor and implemented with the help of data collector.

All these programs need that the instrument station and at least one reference station be
identified so that all subsequent stations can be identified in terms of (X, Y, Z).

Typical programs include the following functions:

Point location
Slope reduction
Missing line measurement (MLM)
Resection
Azimuth calculation
Remote distance and elevation measurement
Offset measurements
Layout or setting out operation
Area computation
Tracking
Stakeout
 REMOTE SENSING
52

various definitions of remote sensing

Technique of acquiring data about an object without touching it.

The non-contact recording of information from various spectral regions of

electromagnetic spectrum (ultraviolet, visible, infrared, and microwave regions) by means
of various instruments (camera, scanners, lasers, linear arrays, and/or frame arrays)
which are located on platforms such as ground, aircraft or spacecraft, and the analysis
of acquired information by means of visual and digital image processing.

Science and art of obtaining information about an object, area, or phenomenon

through the analysis of data acquired by a device that is not in contact with the object,
area, or phenomenon under investigation (Lillesand and Kiefer, 2000)

Photogrammetry and remote sensing are the art, science, and technology of obtaining
reliable information about physical objects and the environment, through the process of
recording, measuring, and interpreting imagery and digital representations of energy
pattern derived from non-contact sensor systems

REMOTE SENSING
53

Remote sensing system

A typical remote sensing system consists of the following sub-systems:

(a) scene
(b) sensor
(c) processing (ground) segment
54
 REMOTE SENSING
56

The following four properties are used for interpretation of RS information:

1. Spectral wavelength or frequency, refractive or emissive properties of objects during
interaction of EMR
2. Spatial viewing angle of sensor, shape & size of the object, position, site, distribution, texture
3. Temporal changes in time and position which affect spectral and spatial properties
4. Polarization object effects in relation to the polarization conditions of the transmitter and
receiver
Multi-concept in RS
The multiple approach, considered to be the main strength of RS, could be described as follows:
Multi-stage : Recording of information from various distances (altitudes: ground, air, and space)
Multi-sensor :Variety of sensors are used to record information, e.g. MSS, TM, LISS, aerial
photography, etc.
Multi-temporal :Sequence of RS observations with different acquisition dates or times.
Multi-spectral :Use of different wavelength bands (visible, infrared, microwave regions) and
combination of different look angles
Multi-polarization : Use of differently polarized microwave data.
Multi-discipline :Experts from different disciplines collaborate
Multi-enhancement : Combination of multi-stage, multi-spectral, multi-sensor, multi-temporal, and
multi-polarization images to enhance interpretation capabilities for information extraction

REMOTE SENSING
57
Comparison of RS with other techniques(Buiten and Clevers, 1993):
facilitates observation of the environment with EMR even outside the visible part of the EM
produces measurable physical data.
gives position-bound thematic information connected with the parameters what, where, when and
how, allowing for improvement and completion of existing maps.
offers flexible approaches in the form of a variety of RS observation techniques and digital image
processing (DIP) algorithms for optimum approach to information extraction.
RS data can be reproduced at any time
In comparison with the human eye, RS instruments offer the possibility of selection, so as to view
objects in more detail and contrast, under a different angle of incidence & from various distances.
provides the unparalleled synoptic view of a region as whole.
provides area-wise information making the traditional way of point-wise sampling of the
earth's surface more selective.
Allows for an image recording of large area in a short time.with a high degree of reality
Data disclose processes on the earth's surface both with regard to an instantaneous reproduction
as well as change detection. Hence, RS can be considered dynamical/temporal.
Satellite images may open up inaccessible regions
RS as source of information may repeat, alter and improve the analysis of the images of the
observed objects can be stored and compared with more recent images at later time.
 REMOTE SENSING
58

A typical RS assignment consists of many linked steps for the successful

interpretation and analysis. (Buiten and Clevers, 1993):
1. Knowledge of RS recording techniques
2. Understanding of physical relationship and interactions between object
and EMR
3. Physical/mathematical modeling regarding the RS of the object concerned
4. Geometric and positioning aspects: matching of images to one another;
registration of images to the geometry of a map projection, called
geocoding;
5. Preprocessing methods of acquired analogue or digital data: interactive
digital image processing and pattern recognition; contribution of private
professional knowledge concerning the objects;
6. Combination techniques with data from other sources: integration with GIS
to update the GIS database by means of the RS results.

REMOTE SENSING
59

Remote sensing in India

India, one of the leading nations in space science, has directed its efforts in three main
areas (Reference ):
Development of remote sensing satellites under Indian Remote Sensing Satellite (IRS)
series
Development of communication and meteorological satellites under INSAT series
Development of different types of launch vehicles to put the satellites in proper
orbits.

In India, Department of Space with ISRO (headquarter at Bangalore) as the nodal

agency is responsible for coordinating all efforts in space technology. National
Remote Sensing Agency (NRSA at Hyderabad) is responsible for satellite data
dissemination to the user community.

So far nine IRS satellites have been launched: IRS-1A, IRS-1B, IRS-1C, IRS-1D, IRS-P3
and IRS-P4 (OCEANSAT), and Technology Experiment Satellite (TES), and IRS-P6
(RESOURCESAT), CARTOSAT-1.
 GEOGRAPHIC INFORMATION SYSTEMS (GIS)
60

Definition of GIS
GIS -Geographic Information System or a particular information system applied to
geographical data
(Information System -set of processes, executed on raw data, to produce information useful in
decision-making. Uses both geographically referenced data as well as non-spatial data)

Or it is a system designed to capture, store, manipulate, analyze, manage, and present spatial
or geographic data.

Why is GIS Important?

By putting maps and other kind of spatial information into digital form, connections between
activities based on geographic proximity can be made. Looking at data geographically can
often suggest new insights, explanations.
GIS has been called an "enabling technology" because of the potential it offers for the wide
variety of disciplines which must deal with spatial data

GEOGRAPHIC INFORMATION SYSTEMS (GIS)

61

Major Areas of Application

Land (parcels) (LIS)
Facilities Management (FIS)
Natural Resource & Environment
Infrastructure Networking

The 4 main ideas of Geographic Information Systems (GIS) are:

Create geographic data.
Manage it in a database.
Analyze and find patterns.
Visualize it on a map.
 GEOGRAPHIC INFORMATION SYSTEMS (GIS)
62

Components of Geographic Information Systems

The 3 main components of Geographic Information Systems are:
1. DATA: GIS stores location data as thematic layers. Each data set has an attribute
table that stores information about the feature. The two main types of GIS data are
RASTER
Raster look like grids because they store data in rows and
columns. They can be discrete or continuous. For example, we
often represent land cover, temperature data and imagery as
raster data.
VECTOR
Vectors are points, lines and polygons with vertices. For
example, fire hydrants, contours and administrative
boundaries are often vectors.
2. HARDWARE: Hardware runs GIS software. It could be anything from powerful servers,
mobile phones or a personal GIS workstation.
3. SOFTWARE: ArcGIS and QGIS are the leaders in GIS software. GIS software
specialize in spatial analysis by using math in maps. It blends geography with modern
technology to measure, quantify and understand our world.

GEOGRAPHIC INFORMATION SYSTEMS (GIS)

63
 Global Navigation Satellite System (GNSS)
64

Global Navigation Satellite System (GNSS)

States, starting a new era in satellite navigation.

orbit by Soviet union.

have two separate and independent tool for navigation and positioning
The four global GNSS systems are GPS (US), GLONASS (Russia), Galileo (EU), BeiDou (China).
Additionally, there are two regional systems QZSS (Japan) and IRNSS or NavIC (India).

NAVSTAR GPS
NAVigation by Satellite Timing And Ranging (NAVSTAR)
DoD) has developed the Navstar GPS, which is an all-
weather, space based navigation system to meet the needs of the USA military forces and
accurately determine their position, velocity, and time in a common reference system, any where
on or near the Earth on a continuous basis (Wooden, 1985).

military, later extended to civilian users.

OneWay communication

Global Positioning System (GPS)

65

Segments of GPS
Space segment: The Space Segment of the system consists of the GPS satellites;
These space vehicles (SVs) send radio signals from space.

-Control segment: The Control Segment consists of a system of tracking stations

located around the world.

-User segment: The GPS User Segment consists of the GPS receivers and the user
community. GPS receivers convert space vehicle (SV) signals into position, velocity,
and time estimates.
 Global Positioning System (GPS)
66

1. Space segment
Satellite orbits

°, separated from each other by 60° in longitude.

kilometres.
third law relates the orbital radius to orbital period, the time
needed by satellite to travel full circle in its plane.

the earth, and is equal to a calendar day minus four minutes).

and the satellites repeats.

day, always four minutes earlier each day.

Satellite signal

particular signal can be tracked with a radio frequency channel in the GPS receiver by looking
unique pseudo random noise (PRN) codes modulation, thereby rejecting all
signals with a different code.

Global Positioning System (GPS)

67

different satellites is called code division multiple access (CDMA).

satellite.

A GPS signal contains three types of data

Unique pseudorandom noise (PRN) codes:
The pseudorandom code is simply an I.D. code that identifies which satellite is transmitting
information.
Satellite ephemerides data :
which is constantly transmitted by each satellite, contains important information about the
status of the satellite (healthy or unhealthy), current date and time. This part of the signal is
essential for determining a position.
Almanac data :
The almanac data tells the GPS receiver where each GPS satellite should be at any time
throughout the day. Each satellite transmits almanac data showing the orbital information
for that satellite and for every other satellite in the system.
 Global Positioning System (GPS)
68

GPS Datum
Datum is a set of parameters (translations, rotations, and scale) used to establish the

From these, users can compute ECEF coordinates of the satellite for a particular
measurement time using well-known equations. The resulting ECEF coordinates are
referenced to the World Geodetic System 1984 (WGS-84).

2. Control Segment: US DoD Monitoring

Global Positioning System (GPS)

69

The control segment consists of five Monitoring Stations (Hawaii, Kwajalein [West
Pacific], Ascension Island [South Atlantic], Diego Garcia [Indian Ocean], Colorado
Springs), three Ground Antennas (Ascension Island, Diego Garcia, Kwajalein).

User Segment

- Selecting one or more satellites

- Acquiring GPS signals
- Measuring and tracking
- Recovering navigation data
 Global Positioning System (GPS)
70

GPS Principles
1. At least four (4) satellites are required to solve four (4) unknown parameters:
Latitude, Longitude, Height and Receiver time offset (difference between the
receiver clock's indicated time
2. a well-defined time scale reference such as UTC (Coordinated Universal Time),
TAI (International Atomic Time) or GPST (GPS Time))

The following 5 basic steps are required to obtain these coordinates:

1. All GPS satellites have synchronized atomic clocks as time keepers.
2. The coordinates of all satellites, acting as moving control stations, are known
precisely with the help of system control.
3. Satellite coordinates and time signals are transmitted to ground receiver.
4. These signals reach the ground delayed by distance traveled.
5. Making use of simple resection principle and the range information to each
satellites, the receiver computes its coordinates

Global Positioning System (GPS)

71

GPS Receiver : Basic Principle

trilateration.
Trilateration works by using the distance from known positions.
 Global Positioning System (GPS)
72

When the receiver knows its

distance from only one satellite,
its location could be anywhere on
the Represented by the earths
surface that is an equal distance
from the satellite.

With signals from two satellites, the receiver

can narrow down its location to just two points
on the earths surface.

Global Positioning System (GPS)

73

Knowing its distance from three

satellites, the receiver can
determine its location because
there is only two possible
combinations and one of them
is out in space.

A fourth satellite must be applied correction to

compensate for the difference between the satellite
and receiver clocks
74
76
78
 GPS SURVEYING
80

Advantages
Unlike conventional surveying procedures, no need for intervisibility between
stations.
Independent of weather conditions as a result of using radio frequencies to
transmit the signals.
Use of same field and data reduction procedures results in position accuracy
which are independent of network shape or geometry and are primarily a
function of inter-station distance.
provides homogeneous accuracy. The points can be established wherever they
are required and need.
more efficient, more flexible and less time consuming positioning technique
obtain high accuracy three dimensional (3D) information, anywhere and any
time with relatively little effort on a global datum .
GPS instrumentation and the data processing software do not radically change
even if very high or moderately high accuracies are required (from 1 part in
104 to 1 part in 106 ).

GPS SURVEYING
81

Current Limitations of GPS

GPS requires clear opening to sky without any obstruction signals by overhanging
branches or structures ; limited applications in densely settled urban areas .
needs careful advanced planning to realize true potential of GPS.
may not be useful for conventional surveys due to intervisibility, shape and geometry
requirements.
Two intervisible stations would have to established by GPS in order to satisfy the
requirement for azimuth data for use by conventional (line-of-sight) survey methods.
reliable coordinate transformation schemes required for transforming GPS coordinates
into a local geodetic system for their integration with results from conventional
surveys.(Since GPS coordinates are available in global WGS-84 datum,)
GPS heights have to be reduced to a sea level datum by suitable
transformation.(Since GPS vertical information is not available in universally acceptable
geoid based height system )
GPS instrumentation is still comparatively expensive.
require skilled personnel for operations.