Agenda

Product Overview & Specification 04-06

Changes over Smart Tank 500/600 series (Poseidon) 08-16
Control Panel Overview 18-19
Error Codes 21-22
Support Mode /Restore Factory & Network Defaults 25-27
Move Printer 29
Known Issues 31-34
Troubleshooting & Servicing 36-43
2 HP Private, Confidential for Internal Use Only
Product Overview & Specification

3 HP Private, Confidential for Internal Use Only

Product Overview
Up to 100-sheet input

Made of over 45%

recycled plastic
content1

Print, scan, copy

Self-healing
Wi-Fi®
Single Band 2.4GHz
(WL & SF)

Smart-guided
buttons

Borderless printing
Low-on-ink
sensors
Up to 6,000 black
pages or 6,000 Up to 30-sheet output
color pages of ink
in the box
Product Specification

Product Name HP Smart Tank 52x All-In- HP Smart Tank 58x All-In- HP Smart Tank 21x Printer
One Printer/ One Printer/
HP Smart Tank 54x All-In- HP Smart Tank 510x All-In-
One Printer One Printer

FCS Date 1 Dec 2022 (India) 27 Mar 2023 (WW)

2 Jan 2023 (NA/ISE)
15 Jan 2023 (GrC/ LAR/ EU3)
1 Feb 2023 (GrA)
1 Mar 2023 (Brazil)

Features Copy/Scan/ Print Copy/Scan/ Print Print ONLY

Connectivity USB ONLY/ HP Smart USB/Wifi/ HP Smart USB/Wifi/ HP Smart

(No Airprint)
5 HP Private, Confidential for Internal Use Only
Product Specification

HP Smart Tank 52x/ 54x HP Smart Tank 58x/ 510x HP Smart Tank 21x
ISO Print Speed (ppm) 12 (Black)/ 5 (Color) 12 (Black)/ 5 (Color) 12 (Black)/ 5 (Color)
Input Tray Capacity (sheets) 100 100 100
Duplex Printing Manual (driver support) Manual (driver support) Manual (driver support)
ADF N/A N/A N/A
Wireless N/A Single Band 2.4G Single Band 2.4G
Bluetooth N/A BLE BLE
Control Panel Essential Lite with ID Copy Essential Lite with ID Copy Essential Lite (No copy)
Low on ink Sensor Yes Yes Yes
Air Purger Auto Auto Auto
Standard Warranty 1 year (30K pages) 1 year (30K pages) 1 year (30K pages)

6 HP Private, Confidential for Internal Use Only

Changes over Smart Tank 500/ 600
Series

7 HP Private, Confidential for Internal Use Only

Changes over Smart Tank 500/600 series
Packaging
Smart Tank 52x/54x/58x/510x/21x series Smart Tank 500/600 series
EPS & Molded Pulp EPS

At Launch Post Launch

8 HP Private, Confidential for Internal Use Only

 Changes over Smart Tank 500/600 series
Product Layout
Smart Tank 52x/54x/58x/510x series Smart Tank 500/600 series
Linked Doors / ID Copy Button/ Scan Lid Opening Non-linked Doors

ID copy button & Scan-Lid opening detection

Front Door and Pen Access Door are NOT linked

Front Door and Pen Access Door are linked **If scan-lid button hole shown is covered with
Thick Dust, the scan detection might fail and
9 HP Private, Confidential for Internal Use Only cause NO buttons light up especially ID copy.
Clean the pocket with tissue or cotton bug should
resolve the issue
Changes over Smart Tank 500/600 series
Control Panel UI
Smart Tank 52x/58x/510x/21x series Smart Tank 500/600 series
Essential Lite Contextual Conventional LCD with Button graphics

WL

ST 52x ST 58x/510x ST 21x

Source:

10 HP Private, Confidential for Internal Use Only

Changes over Smart Tank 500/600 series
IDS
Smart Tank 52x/54x/58x/510x/21x series Smart Tank 500/600 series
Gravity Tank Bubbler Tank

• Black Tank can fill up half the Host Black bottle that is 135ml • Black Tank can fill up Whole the Host Black bottle that is 135ml
• Color Tanks can fill up the whole Host color bottles that are 50ml • Color Tanks can fill up the whole Host color bottles that are 70ml
11 HP Private, Confidential for Internal Use Only
Changes over Smart Tank 500/600 series
Air Purger
Smart Tank 52x/54x/58x/510x/21x series Smart Tank 500/600 series
Auto Air Purger Manual Air Purger

• User first have to remove Orange Tape • User first have to turn the Air Purger handle clockwise
• Unlock Manifold of Carriage, then remove Air Purger • Unlock Manifold of Carriage, then remove Air Purger
12 HP Private, Confidential for Internal Use Only
Changes over Smart Tank 500/600 series
Media Sensing
Smart Tank 58x/ 510x series Smart Tank 500/600 series
Vertical Sensing Media Sensors

Flex Size Indicator

Presence Flag

Presence Flag: Detect media presence Detect media presence & media width
Flex Size Indicator: Detect media width
 Changes over Smart Tank 500/600 series
Media Sensing Behavior – Flatbed Copy
Smart Tank 58x/510x series Smart Tank 500/600 series

Target Media loaded LEBI Poseidon

A4/ LTR Flatbed copy Paper picked > Print actual size > Image crop > Print on platen > E2 Paper picked > Print actual size > Image crop > no error
Unhappy path scenario especially when user 4x6 (small category)
Flatbed copy Paper picked > Print actual size > Image crop >Print on platen > No error Paper picked > Print actual size > Image crop > no error
did not align width adjuster to media edge 5x7 (medium category)
• Original size (Target) : Big (A4/Letter)
Flatbed copy Paper picked > Print actual size > Image crop > Print on platen > E2 Paper picked > Print actual size > Image crop > E2
• Width Adjuster not adjusted (far left) A5 (medium category)
• Loaded size: Smaller than target Flatbed copy Paper picked > Print actual size > Image crop > E2 Paper picked > Print actual size > Image crop > E2
LTR (large category) (Error E2 is due to Derivate default was APJ set to A4, media loaded is Ltr ) (Error E2 is due to Derivate default was APJ set to A4, media
• User bias the media to right , width- loaded is Ltr )
adjuster as shown Flatbed copy Paper picked > print actual size > No Error Paper picked > Print actual size > No Error
• Result: Print on platen A4 (large category) (No error is due to Derivate default was APJ A4, media loaded is A4) (No error is due to Derivate default was APJ A4, media loaded
is A4)
Changes over Smart Tank 500/600 series
Media Sensing Behavior – Print via driver
Smart Tank 58x/510x series Smart Tank 500/600 series

Input Size Media loaded LEBI Poseidon

A4/ LTR 4x6(small category) Paper picked > Print actual size > Image crop > Print on platen > E2 Paper picked > E1 > Paper ejected > no print (with or without
Unhappy path scenario especially when user adjuster)
did not align width adjuster to media edge 5x7(medium category) Paper picked > Print actual size > Image crop >Print on platen > No error Paper picked > E1 > Paper ejected > no print
• Original size (Input size) : Big (A4/Letter)
A5(Medium category) Paper picked > Print actual size > Image crop > Print on platen > E2 Paper picked > E1 > Paper ejected > no print
• Width Adjuster not adjusted (far left)
• Loaded size : Smaller than target LTR(Large category) Paper picked > Print actual size > Image crop > E2 Paper picked > Print actual size > Image crop > E2
• User bias the media to right , width- (Error E2 is due to Derivate default was APJ set to A4, media loaded (Error E2 is due to Derivate default was APJ set to A4,
is Ltr) media loaded is Ltr )
adjuster as shown A4(Large category) Paper picked >Print actual size > No Error Paper picked > Print actual size > No Error
• Result: Print on platen (No error is due to Derivate default was APJ A4, media loaded is A4) (No error is due to Derivate default was APJ A4, media
loaded is A4)
Changes over Smart Tank 500/600 series
Copy - Fit to page
Smart Tank 58x/510x series Smart Tank 500/600 series

• Fit to page option not available • Fit to page option available

• Custom: 25%-150% • Custom: 25%-400%
Control Panel Overview

17 HP Private, Confidential for Internal Use Only

Control Panel Overview
Control Panel Buttons & Lights Icon Description
Shows the number counter or error codes, different copy modes (52x/ 54x/ 58x/ 51xx),
issues relating to ink, printheads, or paper, and for network models, the network
connection status.

Start a color copy job. To increase the number of copies, press and hold the button or
press it multiple times.
Copying starts 2 seconds after the last button press.
Start a black-and-white copy job. To increase the number of copies, press and hold the
button or press it multiple times.
Copying starts 2 seconds after the last button press
The ID Copy feature allows you to place a card
or small-size document anywhere on the scanner glass to copy both sides onto the
same page
Stop the current operation.

Resume a job after a disruption (for example, after loading paper or clearing a paper
jam).

Turn the printer on or off.

ST 52x/54x ST 58x/510x ST21x
Turn on or off the wireless capability of the printer.

Print an information page. The information page provides a summary of the printer
18 HP Private, Confidential for Internal Use Only information and its current status (including network, Wi-Fi Direct, Web Services,
ink, and so on).
Control Panel Overview
Icon Description
Control Panel Display A blinking left icon indicates a problem with the color printhead.
A blinking right icon indicates a problem with the black printhead.

Indicates the side of the card to place on the scanner glass.

Shows the number counter when you are copying documents, changes to the letter A
/ when the printer is doing printhead alignment, and shows the letter E and a number
when the printer is in an error state.
• Blank Document icon: Indicates the status of paper in the input tray or any related
issues (including out of paper, paper jam, and so on).
• Document icon with horizontal lines: Indicates the status of the original on the
scanner glass or any related issues. It also appears when the printer is in the
Document Copy mode, for copying on plain paper.
• Photo icon: This appears when the printer is in the Photo Copy mode, for copying on
photo paper.
Attention light. Indicates an error or warning state.
ST 52x/54x ST 58x/510x ST 21x
Prompts you to open the scanner lid
during printhead alignment or when doing an identification card copy

The KCMY letters and Ink drops are used to indicate status of the four ink tanks in the
printer.
Each set of icons corresponds to an ink tank: black, cyan, magenta, and yellow.
Shows the Wi-Fi status and signal strength.

Indicates the Wi-Fi Direct status.

19 HP Private, Confidential for Internal Use Only • On: Wi-Fi Direct is turned on and ready to use.
• Off: Wi-Fi Direct is off.
Error Codes

20 HP Private, Confidential for Internal Use Only

Error Codes
Error Code Cause Solution
Paper size mismatch (E1) or Paper length mismatch (E2) has 1. Press the Cancel button to cancel printing.
occurred. When printing, the printer detects that the paper size 2. Load paper that matches the size of the page you want to print or change
E1/E2 of the printing job does not match the width or length of the the paper size settings in your application to match the size of the paper
paper loaded. you are using.
3. Print the document again.
1. Open the front door.
2. Make sure the printhead cover is properly closed and the print carriage is
not obstructed. Do not open the printhead cover.
E3 The carriage inside the printer has stalled
3. Remove any jammed paper or other objects blocking the carriage.
4. Close the front door.
5. Press the Resume button to continue printing or press the Cancel button .
Clear the jam, and then press the Resume button to continue printing. For
E4 Paper jam more information, see Clear jams and solve paper-feed issues in user guide.
CAUTION: Do not open the printhead cover.
The scanner is not working 1. Press the Cancel button , and then try scanning again.
E5
(Applicable for 52x/ 54x/ 58x/ 510x only) 2. If scanning still fails, turn the printer off, and then on again.
Restart the printer.
1. Turn off the printer.
E6 The printer is in an error state 2. Unplug the power cord.
3. Wait a minute, and then plug the power cord back in.
4. Turn on the printer.
E7 One or more ink tanks are out of ink. Refill the indicated ink tank that is out of ink.
E8 Fatal error Turn the printer off, and then on again.
21 HP Private, Confidential for Internal Use Only
E9 A firmware or printer update error has occurred Turn the printer off, and then on again.
Control Panel Error Conditions
Error Code Cause Solution
The Attention light and Document icon (with horizontal lines) are Load original, and then press the Resume button begin
blinking. The Resume light and Cancel light are on. copying
The printer receives a copy job, and detects that there is no
original on the scanner glass.

The Attention light and Document icon (Blank Document icon) are Load paper, and then press the Resume button to
blinking. The Resume light and Cancel light are on continue printing
The printer receives a printing job, and detects that there is no
paper in the input tray.

One or more Printhead icons and the Resume light are on. • Make sure both printheads are properly installed.
One of the following might have occurred: • Install any missing printhead.
• One or both printheads are missing. • If both printheads are installed, remove the printhead
• One or both printheads are installed incorrectly. indicated, make sure there is no orange plug or plastic
• One or both printheads still have an orange plug or plastic tape tape on it, and then reinsert the printhead securely.
on them. • Make sure that you are using the correct HP printheads
• One or both printheads are incompatible or damaged. for your printer.

One or more Ink icons and the Resume light are on. Refill the indicated ink tank.
One or more ink tanks are very low on ink.

The Attention light is on, one or more Ink icons are blinking, and the
Resume light is on.
One or more ink tanks are very low on ink.

The Attention light, error code E7, and one or more Ink icons are
22 HP Private, Confidential for Internal Use Only blinking.
One or more ink tanks are out of ink.
 Control Panel Error Conditions
Error Code Cause Solution
Paper Jam Check and clear jammed paper, bits of paper and any
foreign objects from these areas:
E4

Input tray Output tray

Printhead access area Cleanout

**Make sure that carriage moves freely after
jam clearance

23 HP Private, Confidential for Internal Use Only

Support Mode/ Restore Factory &
Network Defaults

24 HP Private, Confidential for Internal Use Only

Support Mode
Common tasks from printer control panel (must be in support mode)
Common Task ST 52x (AIO) Instructions ST 58x/ 510x (WL) & ST 21x (SF WL)
Instructions
Enter Printer Support Mode ➢ Press and hold the Resume button for 3 ➢ Press and hold the Information button for at least
seconds. 5 seconds.
➢ All button lights on the printer control panel will ➢ All button lights on the printer control panel will
light up. light up.
Exit Printer Support Mode ➢ Press the Cancel button once, do not hold the ➢ Press the Cancel button once, do not hold the
button. button.
➢ All button lights will turn off if there are no printer ➢ All button lights will turn off if there are no printer
errors. errors.
Switch between Document Copy 1. Press and hold the Resume button for 3 1. Press and hold the Information button for 5
and Photo Copy modes seconds until the control panel buttons light up. seconds until the control panel buttons light up.
2. Press and hold both copy buttons at the same 2. Press and hold both copy buttons at the same
time for 3 seconds. time for 3 seconds.
** Not applicable for ST 21x
Enter Wi-Fi Protected Setup - Press and hold the Wi-Fi button for at least 3
(WPS) Push Button mode seconds.

Turn Wi-Fi Direct on or off - 1. Press and hold the Information button for 5
seconds until the control panel buttons light up.
25 HP Private, Confidential for Internal Use Only 2. Press the Wi-Fi button and the Resume button at
the same time.
Support Mode
Common tasks from printer control panel (must be in support mode)
Printer Report ST 52x (AIO) Instructions ST 58x/ 510x (WL) & ST 21x (SF WL)
Instructions
Printer Status Page Press the Resume button Press the Resume button .

Print Quality Diagnostic Report Press and hold the Cancel button for 3 seconds ST 58x/ 510x
Press and hold the Color Copy button for 3 seconds.

ST 21x
Press and hold the Cancel button for 3 seconds

Wi-Fi Network Test Report and - Press the Information button and the Resume button
Network Configuration Page at the same time.

Wi-Fi Quick Start Guide - Press the Information button .

Wi-Fi Direct Guide - Press the Information button and the Cancel button
at the same time.

Web Services Reports - Press the Resume button and the Cancel button at
the same time.
26 HP Private, Confidential for Internal Use Only
Restore Factory & Network Defaults
Restore Default ST 52x/ 54x (AIO) Instructions ST 58x/ 510x (WL) & ST 21x (SF WL)
Instructions
Restore factory defaults Restoring the printer to factory defaults returns all Restoring the printer to factory defaults returns all
printer and network settings to the factory defaults. printer and network settings to the factory defaults.
1. Press the Power button and wait for the printer
to completely turn off. ST58x/510x
2. Press the Resume button and Black Copy Same as ST52x
button at the same time.
3. While holding the two buttons, press the Power ST 21x
button to turn on the printer. 1. Press and hold the Information button for 5
4. Keep holding Resume button and Black Copy seconds until the control panel buttons light up.
button for 5 seconds, and then release them. 2. With the front door open, press and hold the
Information button and the Cancel button for at
least 3 seconds.
Restore network defaults - 1. Press and hold the Information button for 5
seconds until the control panel buttons light up.
2. Press the Wi-Fi button and the Cancel button at
the same time for 5 seconds until the Wi-Fi light
blinks blue.

27 HP Private, Confidential for Internal Use Only

Move Printer

28 HP Private, Confidential for Internal Use Only

Move Printer

29 HP Private, Confidential for Internal Use Only

Known Issues

30 HP Private, Confidential for Internal Use Only

Known Issues
HP Smart Tank 52x/ 54x All-In-One Printer
No MacOS support

i. Messaging - Not compatible with macOS label / printed (with country localization) on printer box

ii. Learning material and specification sheets updated

Source:

31 HP Private, Confidential for Internal Use Only

Known Issues
HP Smart Tank 58x/ 510x All-In-One Printer
MacOS users connecting printer using USB cable will not be able to use EWS to change
settings or print reports

Workaround to access EWS:

i. Use HP Smart (from Mac) over wifi connection ii. Access EWS via mobile device over Wifi-Direct
connection
a) Put the printer back into wi-fi setup mode
a) Turn on wifi-Direct (see User Guide “Print
without connecting to same Wi-Fi network
(Wi-Fi Direct)”)
b) Use HP Smart (Mac) to setup the printer to b) Connect the mobile device’s wifi to the
connect to wifi printer’s Wifi-Direct SSID
c) Use HP Smart to access EWS after setup c) Open browser to launch EWS (see User Guide
“To open EWS using an IP address (Wi-Fi
Direct connection)”)
Source:

32 HP Private, Confidential for Internal Use Only

Known Issues
HP Smart Tank 58x/ 510x All-In-One Printer
Intermittent "Unable to connect to printer" instead of Unsupported network type error
message with Redmi mobiles
Correct Wrong
Use case:
➢ User uses redmi mobile to setup printer through HP Smart app
➢ Mobile connected to 5GHz Wi-Fi network
➢ Select 5Ghz SSID and enter the password from HP Smart app
➢ App should show correct message and prompt user to switch
to 2.4GHz network instead of showing wrong message

Workaround:
Connect mobile to 2.4GHz network before setting the printer using HP Smart app

Source:

33 HP Private, Confidential for Internal Use Only

Known Issues
HP Smart Tank 58x/ 510x All-In-One Printer
E2 paper mismatch error not displayed when performing multiple Letter copy job with loading
A4 paper in input tray

Paper Size Set: Letter

Paper loaded in input tray: A4
Multiple page copy, E2 not displayed

Correct behavior: E2 should be displayed after 1st page is printed

Source:

34 HP Private, Confidential for Internal Use Only

Troubleshooting & Servicing

35 HP Private, Confidential for Internal Use Only

Troubleshooting Steps – Paper Path (No pick)
1) Customer Symptom: ii) Paper no pick
i) Paper not detected a) Check if the pick tire & UPG rollers are dirty and any traction;
ii) Paper no pick

2) Troubleshooting Steps: Clean the pick tire & UPG rollers using clean cloth and water/ cleaning kit
• Make sure paper is properly loaded
• Check the media customer is using if it is within supported b) Check any foreign object inside the printer blocking paper path such as
media specification UPG (upper paper guide), star-wheel areas

i) Paper not detected

a) Check Media Presence Flag not broken; if broken replace
whole scanner assembly

c) Check for any part damaged/ dislodged/ broken/ with loose cable
connection/ with ink contamination

Source:
Replace damaged part/s
36 HP Private, Confidential for Internal Use Only
 Troubleshooting Steps – Paper Path (Jam)
1) Customer symptom
• E4 – Paper jam

2) Troubleshooting Steps:
a) Check and clear jammed paper, bits of paper and any foreign c) Check any foreign object inside the printer blocking paper path such as
objects from Input tray. Output tray, Printhead access area and UPG (upper paper guide), starwheel areas
Cleanout

b) Check if the pick tire & UPG rollers is dirty and any traction;

d) Check for any part damaged/ dislodged/ broken/ with loose cable
connection/ with ink contamination

Replace damaged part/s

Clean the pick tire & UPG rollers using clean cloth and water/ cleaning
kit

Source:
Troubleshooting Steps – Paper Path (Mismatch)
Customer Symptom:
• E2 (media mismatch) error after printing first page
• 1st sheet will be printed

Troubleshooting Steps:
a) Check media width adjuster if aligned to media edge/ any damage b) Check flex size indicator is engaged to media width adjuster

If E2 persists, replace entire scanner assembly

Source:

38 HP Private, Confidential for Internal Use Only

Troubleshooting Steps – Carriage Stall/ Jam (E3)
Customer Symptom:
• E3 – Carriage Stall/ Jam
• Carriage don’t move/ collision

Troubleshooting Steps (Cable connection check) :

a) Check carriage motor cable is connected b) Check carriage FFC cable is connected c) Check carriage FFC cable is connected
to MPCA to MPCA to Carriage PCA

d) Check carriage FFC cable for any e) Check for carriage motor harness for
damage/breakage any damage/breakage

For cases d) & e), replace entire backbone assembly

Source:

39 HP Private, Confidential for Internal Use Only

Troubleshooting Steps – Carriage Stall/ Jam (E3)
Customer Symptom:
• E3 – Carriage Stall/ Jam
• Carriage don’t move/ collision

Troubleshooting Steps (Backbone assembly check) :

a) Check carriage PCA for any burn mark or b) Check encoder strip for dislodged/ stain/ c) Check carriage belt for any dislodge/
damage. ink smear. damage/ losing tension.
Replace whole backbone assembly Reinsert or replace encoder strip Replace entire backbone assembly

d) Check any obstruction by moving carriage e) Move carriage to right side and check if
manually from left to right and pen chute/ tube length is too tight.
manifold of any dislodge. Replace entire IDS assembly/ whole unit
Clear obstruction (if any) and reassemble

.
Source:

40 HP Private, Confidential for Internal Use Only

Troubleshooting Steps – Carriage Stall/ Jam (E3)

41 HP Private, Confidential for Internal Use Only

Teardown Sequence & Video
1) Scanner module assembly
2) MPCA board
3) Power supply
4) Carriage & Backbone assembly
5) Speedmech assembly
6) Encoder PCA
7) IDS assembly
8) Output (Starwheel) assembly
9) Feedshaft assembly
10) Separation module assembly
11) Front door

Videos link: LEBI Training Teardown Videos

42 HP Private, Confidential for Internal Use Only
 Combo buttons
ST 52x ST 58x/510x ST21x
Reflash Mode While applying power, press and hold Mono Copy and Cancel. While applying power, press and hold Info and Cancel.
NVM Reset-OOBE
While applying power, press and hold Resume and Cancel. While applying power, press and hold Resume and Cancel.
(Full NVM Reset + Clear Derivative)
NVM Reset-Full While applying power, press and hold Resume and Mono Copy. While applying power, press and hold Info and Resume.
NVM Reset-Semi Full While applying power, press and hold Resume and Color Copy. While applying power, press and hold WiFi and Resume.
Press and hold Power button for more than 4 sec, continue to
Press and hold Power button for more than 4 sec, continue to hold Power button,
hold Power button, then use Cancel for 100's, WiFi for 10's, and
Tap Tests (Print Mech) then use Cancel for 100's, Color Copy for 10's, and Mono Copy for 1's.
Resume for 1’s. Release Power button after Tap test number has
Release Power button after Tap test number has been entered.
been entered.

SELF TEST = 4 This Report PEN_ETEST = 43 Pen Test (auto color) Trigger pen change = 130 Trigger pen change
INFINITE H = 8 Continuous H pattern VERSION STRINGS = 45 Display component version strings Trigger K windscreen wipe = 141 Trigger K windscreen wipe
CUSTOMER_SVC = 10 Customer service page NO_MECHON = 58 Set DSID_NO_MECH (not in NVM) to TRUE Trigger CMY windscreen wipe = 142 Trigger CMY windscreen wipe
SERVO CAL PAGE = 11 Servo cal data tables NO_MECHOFF = 59 Set DSID_NO_MECH (not in NVM) to FALSE Mech DS objects report = 157 Mech DS objects report
INFINITE CH = 13 Continuous color H pattern PRINT MECH CALIBRATION REPORT = 61 Print mech calibration report Servicing counters report = 168 Servicing counters report
PAPER CAL = 14 Schedule a paper cal LIB_HWREPORT = 62 Low-Level Hardware Status Report Mech Telemetry report = 169 Mech Telemetry report
MINI TRACE = 15 Mini Trace report Counters Report = 65 Print the Counters Report WPS PBC START = 194 WPS PBC start trigger
DATA PATH PAGE = 17 Data Path Information Page MANUAL CAL VERIFY PAGE = 82 Manual pen calibration verification page WPS PIN START = 195 WPS PIN start trigger
SPIT N WIPE = 20 Pen recovery level 0 NOZZLE_PATTERN = 84 Print the Pen Nozzle Pattern WIRELESS METRICS DATA REPORT = 206 Print Wireless Metrics Data Report
CLEAN PENS = 21 Pen recovery level 1 MAX_PWM = 90 Max motor pwm report PEN OOBE RESET = 210 Reset pen for OOBE(Unsecure FW only)
SUPER CLEAN = 22 Pen recovery level 2 CONT_PK_DRAFT = 96 Continuous Pick & Kick Draft Reset networking = 230 Change all networking values to factory defaults
Prime K Pen = 23 Prime K Pen CONT_PK_NORMAL = 97 Continuous Pick & Kick Normal NETWORK_CONFIG = 240 current network config info
Prime CMY Pen = 24 Prime CMY Pen FW UPDATE = 105 Firmware Update Page DCL STATUS = 241 DCL Integrated Status
Mini Sift = 25 Mini Sift Report MECH_VRFY_CARRUNCAP = 110 Mech Verify Carriage (with uncap) NETWORK_CORE_CONFIG = 242 current core network config info
Cleaner for pick tire = 37 Cleaner for pick tire MECH_VRFY_CARRIAGE = 111 Mech Verify Carriage (no uncap) Power Supply Report = 500 Power supply information.
Cleaner for ribs mears = 38 Cleaner for rib smears MECH_VRFY_SERV_STN = 112 Mech Verify Service Station Thermal Model Report = 501 Thermal model information.
PEN_ETEST = 41 Pen Test (color) MECH_VRFY_PICK_KICK = 113 Mech Verify Pick & Kick INPUT TRAY IR SENSORS = 916 IR Sensor State Report
PEN_ETEST = 42 Pen Test (black) PEN_TTOE = 114 Pen TTOE values AIO SELF TEST = 919 Printer Status Report

43 HP Private, Confidential for Internal Use Only

Q&A
44 HP Private, Confidential for Internal Use Only
Thank you