Numerical Control

1
 Numerical Control

 Numerical control (NC) is the technique of

giving instructions to a machine in the form of
a code which consists of numbers, letters of
the alphabet, punctuation marks and certain
other symbol.

 Controlling a machine tool by means of a

prepared program is known as numerical
control.

2
 Numerical Control
 Instructions are supplied to the machine as
blocks of information.
 Each block is given a sequence number for
identification.
 The set of instructions are organized in logical
manner to direct the machine tool to carry
out a specific task. It is thus termed as part
program.
3
 Numerical Control
 The part program is the set of detailed step-
by-step commands that direct the actions of
the processing equipment.
 The numerical data required for producing a
part is maintained on a punched tape.
 The punched tape is moved forward by one
block each time the cutting of a segment is
completed.

4
 Numerical Control
 In machine tool applications, the person who
prepares the program is called a part
programmer.
 The part programmer must possess
knowledge and experience of tools, cutting
fluids, machinability data and fixture design
techniques.
 Part programs are written manually or by
using a computer-aided language, such as
automated program tool (APT)
5
 Basic Elements of NC / CNC
Machines
Any CNC machine essentially consists of the
following elements:

1. Part Program
2. Program Input Device
3. Machine Control Unit (MCU)
4. Drive System
5. Machine Tool
6. Feedback System
6
Basic Elements of NC / CNC
Machines

7
Basic Elements of NC / CNC
Machines

8
 Basic Elements of NC / CNC
Machines
1. Part Program

9
 Basic Elements of NC / CNC
Machines
2. Program Input Device

The program input device is the means for part

program to be entered into the NC / CNC control.

Three commonly used program input devices are

punch tape reader, magnetic tape reader, and
computer via RS-232C Cable or USB
communication.

10
 Basic Elements of NC / CNC
Machines
2. Program Input Device

11
 Basic Elements of NC / CNC
Machines
3. Machine Control Unit (MCU)

The machine control unit (MCU) is the heart of a

CNC system.

There are two sub-units in the machine control unit:

a) Data Processing Unit (DPU)

b) Control Loop Unit (CLU)

12
 Basic Elements of NC / CNC
Machines
a) Data Processing Unit

On receiving a part program, the DPU first interprets

and encodes the program into internal machine
codes.

The interpolator of the DPU then calculates the

intermediate positions of the motion in term of basic
length unit.

13
 Basic Elements of NC / CNC
Machines
a) Data Processing Unit

Basic length unit (BLU) is the smallest unit length

that can be handled by the controller

If 1 BLU = 0.0001” that means axis will move

0.0001” for every electrical pulse received by the
motor.

The calculated data are passed to CLU for further

action. 14
 Basic Elements of NC / CNC
Machines
b) Control Loop Unit

The data from DPU is converted into electrical

signals in the CLU to control the driving system to
perform the required motions.

 CLU implement interpolations (linear, circular,

and helical) to generate axis motion commands.

 It feed the axis motion commands to the amplifier

circuits for driving the axis mechanisms.
15
 Basic Elements of NC / CNC
Machines
b) Control Loop Unit

 CLU receive the feedback signals of position and

speed for each drive axis.

 It also implement auxiliary control functions such

as coolant or spindle on/off and tool change.

16
 Basic Elements of NC / CNC
Machines
4. Drive System

 A drive system consists of amplifier circuits,

drive motors, and ball lead-screws.
 The MCU feeds the control signals (position and
speed) of each axis to the amplifier circuits.
 The control signals are augmented to actuate
drive motors which in turn rotate the ball lead-
screws to position the machine table
17
 Basic Elements of NC / CNC
Machines
4. Drive System

18
 Basic Elements of NC / CNC
Machines
5. Machine Tool

 CNC controls are used to control various types of

machine tools.
 Regardless of which type of machine tool is
controlled, it always has a work table and a
spindle to control of position and speed.
 The machine table is controlled in the X and Y
axes, while the spindle runs along the Z axis.
19
 Basic Elements of NC / CNC
Machines
6. Feedback System

 The feedback system is also referred to as the

measuring system
 It uses position and speed transducers to
continuously monitor the position at which the
cutting tool is located
 The MCU uses the difference between reference
signals and feedback signals to generate the control
signals for correcting position and speed error
20
 Basic Elements of NC / CNC
Machines
6. Feedback System

21
 NC Coordinate Systems
A standard axis system to position work head
(tool) relative to the work part must be
specified by the part programmer.

There are two axis systems used in NC for the

following parts:

1. Flat and prismatic parts

2. Rotational parts
22
 NC Coordinate Systems
 The axis system for flat and block-like parts
consists of the three linear axes (x, y, z) in
the Cartesian coordinate system, plus three
rotational axes (a, b, c), as shown in Figure
1(a).

 Positioning scheme referred in Fig 1(a) is

adequate for simple NC applications such as
drilling and punching of flat sheet metal.

23
 NC Coordinate Systems

Figure 1 Coordinate systems used in NC (a) for flat and

prismatic work and (b) for rotational work. 24
 NC Coordinate Systems
 The a-, b-, and c-rotational axes specify angular
positions about the x-, y-, and z-axes, respectively.

 Machine tools with rotational axis capability have

either four or five axes: three linear axes plus one
or two rotational axes.

 The coordinate axes for a rotational NC system are

illustrated in Figure 1(b). These systems are
associated with NC lathes and turning machines.

25
 NC Coordinate Systems
 The part programmer must decide where the
origin of the coordinate axis system should be
located.

 For example, the origin might be located at one of

the corners of the part.

 If the work part is symmetrical, the zero point

might be most conveniently defined at the center
of symmetry.

26
 Motion Control System
If the work head is moving (e.g. turning, milling,
continuous arc welding) , it may be necessary to
follow a straight line path or a circular or other
curvilinear path.

Different types of movement are accomplished by two

main types of motion control system:

1. Pont-to-point system
2. Continuous system

27
 Motion Control System
1. Point-to-point systems:

It is also called positioning systems and move the

worktable to a programmed location

Once the move has been completed, some

processing action is accomplished by the work head
at the location, such as drilling or punching a hole.

The program consists of a series of point locations at

which operations are performed, as depicted in
Figure 2.
28
Motion Control System

Figure 2: Point-to-point (positioning) control in NC.

At each x–y position, table movement stops to perform
the hole-drilling operation. 29
 Motion Control System
2. Continuous path systems:

Continuous path systems are capable of controlling

two or more axes simultaneous to control the tool
trajectory relative to the work part.

In this case, the tool performs the process while the

worktable is moving, thus enabling the system to
generate angular surfaces, two-dimensional curves,
or three-dimensional contours

30
 Motion Control System
2. Continuous path systems:

This control mode is required in many milling and

turning operations.

A simple two-dimensional profile milling operation is

shown in Figure 3 to illustrate continuous path
control.

31
 Motion Control System

Figure 3: Continuous path control in NC (x–y plane only). Note

that cutting tool path must be offset from the part outline by
a distance equal to its radius.
32
 Motion Control System
When continuous path control is utilized to move the
tool parallel to only one of the major axes of the
machine tool worktable, this is called straight-cut
NC.

When continuous path control is used for

simultaneous controlling two or more axes
in machining operations, the term contouring is
used.

33
 Motion Control System
Interpolation Methods

The paths that a contouring-type NC system is

required to generate, often consist of circular arcs and
other smooth nonlinear shapes.

Some of these shapes can be defined mathematically

by relatively simple geometric formulas (e.g., the
equation for a circle is x2 + y2 = R2 ; where R = the
radius of the circle and the center of the circle is at the
origin), whereas others cannot be mathematically
defined except by approximation
34
 Motion Control System
Interpolation Methods

To cut along a circular path, the circle must be divided

into a series of straight line segments that
approximate the curve.

The tool is commanded to machine each line segment

in sequence so that the machined surface closely
matches the desired shape.

35
 Motion Control System
Interpolation Methods

If the programmer were required to specify the

endpoints for each of the line segments, the
programming task would be extremely difficult and
with errors.
The part program would be extremely long because of
the large number of points.
To ease the burden, interpolation routines have been
developed that calculate the intermediate points to be
followed by the cutter to generate a path.
36
 Motion Control System
Interpolation Methods

A number of interpolation methods are available

which are as follows:
1. Linear interpolation
2. Circular “-”
3. Helical “-”
4. Parabolic “-”
5. Cubic “-”
The interpolation module in the MCU performs the
calculations and directs the tool along the path.
37
 Types of Interpolations
In linear interpolation, the tool moves in a straight line from
start to end (Fig. a) along two or three axes.

Theoretically, all types of profiles can be produced by

continuous path by making small increments between the
points (Fig. b), but a large amount of data has to be processed
in order to do so. 38
 Types of Interpolations

In circular interpolation (Fig. c), the inputs required for the path
are;
1) coordinates of the endpoints
2) coordinates of the center of the circle and its radius
3) the direction of the tool along the arc.

39
 Motion Control System
Absolute vs. Incremental Positioning

Absolute positioning:
The work head locations are always defined with
respect to the origin of the axis system

Incremental positioning:
The work head position is defined relative to the
present location

40
 Motion Control System
Absolute vs. Incremental Positioning

The work head is presently at point

(20, 20) and is to be moved to point
(40, 50).

In absolute positioning, the move is

specified by x = 40, y = 50.

In incremental positioning, the move

is specified by x = 20, y = 30.

Absolute versus incremental positioning

41
 Analysis of Positioning Systems
 NC positioning system converts the coordinate axis values in
the NC part program into relative positions of the tool and work
part during processing.

 The system consists of a cutting tool and a worktable on which

a work part is fixture as shown in figure.

 The worktable moves linearly by means of a rotating leadscrew

or ballscrew, which is driven by a stepper motor or servo motor.

42
 Analysis of Positioning Systems
 The screw has a certain pitch p, (in/rev) and the table
moves a distance equal to the pitch for each revolution.

 The velocity of the worktable, which corresponds to

the feed rate in a machining operation, is determined
by the rotational speed of the screw

43
Analysis of Positioning Systems
Two types of control systems are used in positioning
systems:

(a) open loop

(b) closed loop

Two types of motion control in NC: (a) open loop and (b) closed loop
44
 Analysis of Positioning Systems
(a) Open loop control systems

 The open loop control means that there is no feedback

 It uses stepping motors for driving the leadscrew
 A stepping motor is a device whose output shaft rotates
through a fixed angle in response to an input pulse as
shown in the figure.

45
 Analysis of Positioning Systems
(a) Open loop control systems

 Excessive load torque may occur in motors due to the

cutting forces in machine tools

 Therefore, this system is suitable for cases where the

tool force does not exist (example: laser machining,
electric-discharge machining etc.)

46
 Analysis of Positioning Systems
(a) Open loop control systems

 The stepper motor is driven by a series of electrical

pulses generated by MCU
 Each pulse causes the motor to rotate a fraction of one
revolution
 The fraction is expressed in terms of the step angle “α”
α = 360 / N (degrees)
where N= number of pulses required for a revolution
47
 Analysis of Positioning Systems
(a) Open loop control systems

 If the motor receives “n” number of pulses, then the

total angel;
A = n (360 / N) (degrees)
 If there is a 1:1 gear ratio between the motor and the
leadscrew then the leadscrew has (n/N) revolutions
 If the pitch of the leadscrew is p (in/rev), then the
distance travelled axially be;
x = p (n / N)
48
 Analysis of Positioning Systems
(a) Open loop control systems

 The pulse frequency, f, in pulses/sec determines the

travel speed of the tool or the workpiece
f = N (RPM) / 60
where,
N = number of pulses per revolution
RPM = RPM of the lead screw
 The travel speed V is;
V= p (RPM)
where, p = pitch (in/rev)
49
 Analysis of Positioning Systems

Example Problem 1

50
 Analysis of Positioning Systems

Example Problem 2

51
 Analysis of Positioning Systems
(b) Closed loop control systems

 Closed loop NC systems are appropriate when there is

a force resisting the movement of the tool / workpiece
(example: Turning, milling etc.)
 In these systems the DC servomotor and feedback
devices are used to ensure that the desired position is
achieved.

52
 Analysis of Positioning Systems
(b) Closed loop control systems

 Both the input to the control loop and the feedback

signals are a sequence of pulses, each pulse represents
BLU (basic unit length)
 The two sequences are correlated by comparator and
gives a signal, by means of digital-to-analog converter
(DAC) to operate the drive motor

53