Scribd
Upload
36 views32 pages

Power Amplifiers - 1

Uploaded by

tadashih.paritho
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
36 views32 pages

Power Amplifiers - 1

Uploaded by

tadashih.paritho
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 32

Power Amplifiers

Power Amplifiers

A ‘Power Amplifier (PA)’ or a ‘Large-Signal Amplifier’ is an amplifier that is designed


to deliver a ‘large’ amount of power to a load.

‘Large’  generally > 500mW (typically, a few watts – tens/hundreds of watts)

Less than 500mW  Small-Signal Amplifier (SSA) (Some books  the boundary is 1W)

Power handling capacity and efficiency are of little concern for SSA
- Opposites are true for PA
Applications

In the last stage of an amplifier system where the electronics need to drive a large
mechanical load, e.g.,

(1) Audio Systems : to drive large speakers,


(2) Radio Transmitters: to broadcast over the airwaves,
(3) Microwave Heating: to provide sufficient heating,
(4) Robotics: to drive a mechanical system.

Almost all Electronic – Mechanical interfaces require power amplifiers.


Performance Parameters

Compared to a small-signal amplifier, a PA needs special consideration with respect to the


following matters:

1. Conversion efficiency: A figure-of-merit for a PA.

average ac power delivered to the load 𝑷𝒐 (𝒂𝒄)


𝜂= =
average dc power drawn by the circuite 𝑷𝒊 (𝒅𝒄)

For a PA, a high 𝜂 is required, otherwise high power will be absorbed by the PA circuit
which may cause heat dissipation problem.
2. Power dissipation capability: The ability of a PA to dissipate heat effectively.
Since it handles high power, it may absorb significantly large power which must be
dissipated quickly in the environment. Otherwise the transistors involved may burn out.

 Large in size.
 Manufacturing methods could be different: materials, process etc.
 Heat sink may be required, etc.
 May require fan to take away heat

3. Distortion: The change in the output waveshape from its input waveshape

 A large voltage/current swing may make a PA more vulnerable to distortion.


 Measured by THD (Third-Harmonic-Distortion) content
Classification of PA

Classes of Operation: Depending on the duration for which the transistors remain in the
‘ON’ state with respect to the input signal cycle

1. Class A

2. Class B

3. Class AB

4. Class C
Classification of PA
Conduction angle < 180°

Conduction angle 360°

Conduction angle 180°

Conduction angle > 180°


Class A Operation

Conduction angle 360°


Class B Operation

Conduction angle for each


transistor 180°
Class B Operation

Cross-Over Distortion
Class AB Operation

Conduction angle slightly


more than 180°
Class C Operation

Conduction angle less than


180°
DC and AC Load Lines of Amplifiers

Example: Common-Emitter Amplifier

C  Coupling Capacitors  Open circuits to DC, short circuits to AC for amplifier operating frequencies

𝑅𝑑𝑐 ≡ Total resistance around the collector-emitter loop under DC conditions


𝑅𝑎𝑐 ≡ Total resistance around the collector-emitter loop under DC conditions
𝑅𝑑𝑐 = 𝑅𝐶 + 𝑅𝐸
and, 𝑅𝑎𝑐 = 𝑅𝐶 ||𝑅𝐿 + 𝑅𝐸

So, 𝑅𝑎𝑐 < 𝑅𝑑𝑐


Equation of DC Load Line:
𝑉𝐶𝐶 − 𝐼𝐶 𝑅𝐶 − 𝑉𝐶𝐸 − 𝐼𝐶 𝑅𝐸 = 0

−𝑉𝐶𝐸 𝑉𝐶𝐶
∴ 𝐼𝐶 = +
𝑅𝐶 +𝑅𝐸 𝑅𝐶 +𝑅𝐸

−𝑉𝐶𝐸 𝑉𝐶𝐶
∴ 𝐼𝐶 = + (𝑦 = 𝑚𝑥 + 𝐶)
𝑅𝑑𝑐 𝑅𝑑𝑐

−1
Slope of DC load line =
𝑅𝑑𝑐

−1
Slope of the AC load line must be
𝑅𝑎𝑐
or, 𝑅𝑎𝑐 < 𝑅𝑑𝑐
Equation of AC Load Line:
Choice of Load Lines for Maximum Output Swing:
At Q-point, we can write:
−𝑉 𝑉 −𝑉 𝑉 𝑉
𝐼𝐶𝑄 = 𝐶𝐸𝑄 + 𝐶𝐶 = 𝐶𝐸𝑄 + 𝐶𝐸𝑄 + 𝐶𝐸𝑄
𝑅𝑑𝑐 𝑅𝑑𝑐 𝑅𝑎𝑐 𝑅𝑎𝑐 𝑅𝑎𝑐

𝑉𝐶𝐶 𝑅𝑎𝑐 = 𝑉𝐶𝐸𝑄 𝑅𝑎𝑐 + 𝑉𝐶𝐸𝑄 𝑅𝑑𝑐

𝑉𝐶𝐶 𝑅𝑎𝑐 𝑉𝐶𝐶 𝑉𝐶𝐶


𝑉𝐶𝐸𝑄 =  𝑉𝐶𝐸𝑄 = 𝑅 and 𝐼𝐶𝑄 =
𝑅𝑑𝐶 + 𝑅𝑑𝐶 1+ 𝑅𝑑𝐶 𝑅𝑑𝐶 + 𝑅𝑎𝐶
𝑎𝐶
Power Amplifier Circuits: Class A
Inductively-Coupled Amplifier:
𝑉𝐶𝐶 𝑉𝐶𝐶
𝑉𝐶𝐸𝑄 = 𝑅 and 𝐼𝐶𝑄 =
1+ 𝑑𝐶 𝑅𝑑𝐶 + 𝑅𝑎𝐶
𝑅𝑎𝐶

Assuming 𝑅𝐿 ≫ 𝑅𝐸 ,

𝑉𝐶𝐸𝑄 ≈ 𝑉𝐶𝐶 , and

The AC load line intersects the 𝑣𝐶𝐸 axis at approximately 2𝑉𝐶𝐶 .


Transformer-Coupled Amplifier:
Design Example
𝐼𝑜 𝑅
We can derive: 𝐴𝑖 = = 𝑅𝐵 𝐵
𝐼𝑖 +𝑅𝐸
𝛽
𝑅𝐵 = 𝑅1 ||𝑅2

𝐼𝑜 = (1 + ℎ𝑓𝑒 )𝐼𝑏

𝐼𝑜 (1+ℎ𝑓𝑒 )𝐼𝑏
𝑉𝑖 = ℎ𝑖𝑒 𝐼𝑏 + 𝑅𝐸 (1 + ℎ𝑓𝑒 )𝐼𝑏 𝐴𝐼 = =ℎ
𝐼𝑖 𝑖𝑒 +𝑅𝐸 1+ℎ𝑓𝑒 +𝑅𝐵
𝐼𝑏
𝑅𝐵
𝑅𝐵
𝑉𝑖 ℎ𝑖𝑒 + 𝑅𝐸 (1 + ℎ𝑓𝑒 ) = 𝑅𝐵 ℎ𝑖𝑒 (since, 1 + ℎ𝑓𝑒 = 𝛽)
𝐼𝐵 = = 𝐼𝑏 𝛽
+ 𝛽
+𝑅𝐸
𝑅𝐵 𝑅𝐵 𝛽𝑅𝐵
≈ 𝑅𝐵 +𝛽𝑅𝐸
𝐼𝑖 = 𝐼𝐵 + 𝐼𝑏

ℎ𝑖𝑒 +𝑅𝐸 1+ℎ𝑓𝑒 +𝑅𝐵


= 𝐼𝑏
𝑅𝐵
Sometimes, problem statements may require you to find 𝑅𝑖𝑛 .

It can be shown that:


𝑉 𝑅𝐸 𝑅𝐵
𝑅𝑖𝑛 = 𝑖 = 𝑅
𝐼𝑖 𝑅𝐸 + 𝛽𝐵
𝛽𝑅𝐸 𝑅𝐵
=
𝛽𝑅𝐸 +𝑅𝐵

= 𝛽𝑅𝐸 || 𝑅𝐵

𝑅
Anyway, we derived: 𝐴𝑖 = 𝑅𝐵 𝐵
𝛽
+𝑅𝐸

We have, 𝐴𝑖 = 10
𝑅𝐸 =

Plugging these values in the equation of 𝐴𝑖 :

You might also like