q172 & q173dcpu manual

MITSUBISHI ELECTRIC
Motion Controllers
User's Manual
Q173DCPU
Q172DCPU
01 01 2008
B(NA)-0300133 MITSUBISHI ELECTRIC INDUSTRIAL AUTOMATION
Version A
SAFETY PRECAUTIONS
(Please read these instructions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual
carefully and pay full attention to safety to handle the product correctly.
These precautions apply only to this product. Refer to the Users manual of the QCPU module to use for a
description of the PLC system safety precautions.
In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".
Indicates that incorrect handling may cause hazardous

DANGER conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous

CAUTION conditions, resulting in medium or slight personal injury or
physical damage.
Depending on circumstances, procedures indicated by CAUTION may also be linked to serious

results.
In any case, it is important to follow the directions for usage.
Please save this manual to make it accessible when required and always forward it to the end user.
A-1
For Safe Operations
1. Prevention of electric shocks
DANGER
Never open the front case or terminal covers while the power is ON or the unit is running, as this
may lead to electric shocks.
Never run the unit with the front case or terminal cover removed. The high voltage terminal and
charged sections will be exposed and may lead to electric shocks.
Never open the front case or terminal cover at times other than wiring work or periodic
inspections even if the power is OFF. The insides of the Motion controller and servo amplifier are
charged and may lead to electric shocks.
Completely turn off the externally supplied power used in the system before mounting or removing the
module, performing wiring work, or inspections. Failing to do so may lead to electric shocks.
When performing wiring work or inspections, turn the power OFF, wait at least ten minutes, and
then check the voltage with a tester, etc.. Failing to do so may lead to electric shocks.
Be sure to ground the Motion controller, servo amplifier and servomotor. (Ground resistance :
100 or less) Do not ground commonly with other devices.
The wiring work and inspections must be done by a qualified technician.
Wire the units after installing the Motion controller, servo amplifier and servomotor. Failing to do
so may lead to electric shocks or damage.
Never operate the switches with wet hands, as this may lead to electric shocks.
Do not damage, apply excessive stress, place heavy things on or sandwich the cables, as this
Do not touch the Motion controller, servo amplifier or servomotor terminal blocks while the power
is ON, as this may lead to electric shocks.
Do not touch the built-in power supply, built-in grounding or signal wires of the Motion controller
and servo amplifier, as this may lead to electric shocks.
2. For fire prevention

CAUTION
Install the Motion controller, servo amplifier, servomotor and regenerative resistor on
incombustible. Installing them directly or close to combustibles will lead to fire.
If a fault occurs in the Motion controller or servo amplifier, shut the power OFF at the servo
amplifier’s power source. If a large current continues to flow, fire may occur.
When using a regenerative resistor, shut the power OFF with an error signal. The regenerative
resistor may abnormally overheat due to a fault in the regenerative transistor, etc., and may lead
to fire.
Always take heat measures such as flame proofing for the inside of the control panel where the
servo amplifier or regenerative resistor is installed and for the wires used. Failing to do so may
lead to fire.
Do not damage, apply excessive stress, place heavy things on or sandwich the cables, as this may
lead to fire.
A-2
3. For injury prevention
CAUTION
Do not apply a voltage other than that specified in the instruction manual on any terminal.
Doing so may lead to destruction or damage.
Do not mistake the terminal connections, as this may lead to destruction or damage.
Do not mistake the polarity ( + / - ), as this may lead to destruction or damage.
Do not touch the heat radiating fins of controller or servo amplifier, regenerative resistor and
servomotor, etc., while the power is ON and for a short time after the power is turned OFF. In this
timing, these parts become very hot and may lead to burns.
Always turn the power OFF before touching the servomotor shaft or coupled machines, as these
parts may lead to injuries.
Do not go near the machine during test operations or during operations such as teaching.
Doing so may lead to injuries.
4. Various precautions
Strictly observe the following precautions.
Mistaken handling of the unit may lead to faults, injuries or electric shocks.
(1) System structure
CAUTION
Always install a leakage breaker on the Motion controller and servo amplifier power source.
If installation of an electromagnetic contactor for power shut off during an error, etc., is specified in
the instruction manual for the servo amplifier, etc., always install the electromagnetic contactor.
Install the emergency stop circuit externally so that the operation can be stopped immediately and
the power shut off.
Use the Motion controller, servo amplifier, servomotor and regenerative resistor with the correct
combinations listed in the instruction manual. Other combinations may lead to fire or faults.
Use the CPU module, base unit and motion module with the correct combinations listed in the
instruction manual. Other combinations may lead to faults.
If safety standards (ex., robot safety rules, etc.,) apply to the system using the Motion controller,
servo amplifier and servomotor, make sure that the safety standards are satisfied.
Construct a safety circuit externally of the Motion controller or servo amplifier if the abnormal
operation of the Motion controller or servo amplifier differ from the safety directive operation in the
system.
In systems where coasting of the servomotor will be a problem during the forced stop, emergency
stop, servo OFF or power supply OFF, use dynamic brakes.
Make sure that the system considers the coasting amount even when using dynamic brakes.
In systems where perpendicular shaft dropping may be a problem during the forced stop,
emergency stop, servo OFF or power supply OFF, use both dynamic brakes and electromagnetic
brakes.
A-3
CAUTION
The dynamic brakes must be used only on errors that cause the forced stop, emergency stop, or
servo OFF. These brakes must not be used for normal braking.
The brakes (electromagnetic brakes) assembled into the servomotor are for holding applications,
and must not be used for normal braking.
The system must have a mechanical allowance so that the machine itself can stop even if the
stroke limits switch is passed through at the max. speed.
Use wires and cables that have a wire diameter, heat resistance and bending resistance
compatible with the system.
Use wires and cables within the length of the range described in the instruction manual.
The ratings and characteristics of the parts (other than Motion controller, servo amplifier and
servomotor) used in a system must be compatible with the Motion controller, servo amplifier and
servomotor.
Install a cover on the shaft so that the rotary parts of the servomotor are not touched during
operation.
There may be some cases where holding by the electromagnetic brakes is not possible due to the
life or mechanical structure (when the ball screw and servomotor are connected with a timing belt,
etc.). Install a stopping device to ensure safety on the machine side.
(2) Parameter settings and programming

CAUTION
Set the parameter values to those that are compatible with the Motion controller, servo amplifier,
servomotor and regenerative resistor model and the system application. The protective functions
may not function if the settings are incorrect.
The regenerative resistor model and capacity parameters must be set to values that conform to
the operation mode, servo amplifier and servo power supply module. The protective functions
Set the mechanical brake output and dynamic brake output validity parameters to values that are
compatible with the system application. The protective functions may not function if the settings
are incorrect.
Set the stroke limit input validity parameter to a value that is compatible with the system
application. The protective functions may not function if the setting is incorrect.
Set the servomotor encoder type (increment, absolute position type, etc.) parameter to a value
that is compatible with the system application. The protective functions may not function if the
setting is incorrect.
Set the servomotor capacity and type (standard, low-inertia, flat, etc.) parameter to values that
are compatible with the system application. The protective functions may not function if the
settings are incorrect.
Set the servo amplifier capacity and type parameters to values that are compatible with the
system application. The protective functions may not function if the settings are incorrect.
A-4
CAUTION
Use the program commands for the program with the conditions specified in the instruction
manual.
Set the sequence function program capacity setting, device capacity, latch validity range, I/O
assignment setting, and validity of continuous operation during error detection to values that are
compatible with the system application. The protective functions may not function if the settings
are incorrect.
Some devices used in the program have fixed applications, so use these with the conditions
specified in the instruction manual.
The input devices and data registers assigned to the link will hold the data previous to when
communication is terminated by an error, etc. Thus, an error correspondence interlock program
specified in the instruction manual must be used.
Use the interlock program specified in the intelligent function module's instruction manual for the
program corresponding to the intelligent function module.
(3) Transportation and installation

CAUTION
Transport the product with the correct method according to the mass.
Use the servomotor suspension bolts only for the transportation of the servomotor. Do not
transport the servomotor with machine installed on it.
Do not stack products past the limit.
When transporting the Motion controller or servo amplifier, never hold the connected wires or
cables.
When transporting the servomotor, never hold the cables, shaft or detector.
When transporting the Motion controller or servo amplifier, never hold the front case as it may fall
off.
When transporting, installing or removing the Motion controller or servo amplifier, never hold the
edges.
Install the unit according to the instruction manual in a place where the mass can be withstood.
Do not get on or place heavy objects on the product.
Always observe the installation direction.
Keep the designated clearance between the Motion controller or servo amplifier and control panel
inner surface or the Motion controller and servo amplifier, Motion controller or servo amplifier and
other devices.
Do not install or operate Motion controller, servo amplifiers or servomotors that are damaged or
that have missing parts.
Do not block the intake/outtake ports of the Motion controller, servo amplifier and servomotor with
cooling fan.
Do not allow conductive matter such as screw or cutting chips or combustible matter such as oil
enter the Motion controller, servo amplifier or servomotor.
A-5
CAUTION
The Motion controller, servo amplifier and servomotor are precision machines, so do not drop or
apply strong impacts on them.
Securely fix the Motion controller, servo amplifier and servomotor to the machine according to
the instruction manual. If the fixing is insufficient, these may come off during operation.
Always install the servomotor with reduction gears in the designated direction. Failing to do so
may lead to oil leaks.
Store and use the unit in the following environmental conditions.
Conditions
Environment
Motion controller/Servo amplifier Servomotor
Ambient 0°C to +40°C (With no freezing)
According to each instruction manual.
temperature (32°F to +104°F)
80% RH or less
Ambient humidity According to each instruction manual.
(With no dew condensation)
Storage -20°C to +65°C
According to each instruction manual.
temperature (-4°F to +149°F)
Indoors (where not subject to direct sunlight).
Atmosphere
No corrosive gases, flammable gases, oil mist or dust must exist
Altitude 1000m (3280.84ft.) or less above sea level
Vibration According to each instruction manual
When coupling with the synchronous encoder or servomotor shaft end, do not apply impact such
as by hitting with a hammer. Doing so may lead to detector damage.
Do not apply a load larger than the tolerable load onto the synchronous encoder and servomotor
shaft. Doing so may lead to shaft breakage.
When not using the module for a long time, disconnect the power line from the Motion controller
or servo amplifier.
Place the Motion controller and servo amplifier in static electricity preventing vinyl bags and store.
When storing for a long time, please contact with our sales representative.
Also, execute a trial operation.
A-6
(4) Wiring
CAUTION
Correctly and securely wire the wires. Reconfirm the connections for mistakes and the terminal
screws for tightness after wiring. Failing to do so may lead to run away of the servomotor.
After wiring, install the protective covers such as the terminal covers to the original positions.
Do not install a phase advancing capacitor, surge absorber or radio noise filter (option FR-BIF)
on the output side of the servo amplifier.
Correctly connect the output side (terminal U, V, W). Incorrect connections will lead the
servomotor to operate abnormally.
Do not connect a commercial power supply to the servomotor, as this may lead to trouble.
Do not mistake the direction of the surge absorbing diode
installed on the DC relay for the control signal output of brake Servo amplifier
signals, etc. Incorrect installation may lead to signals not being VIN
(24VDC)
output when trouble occurs or the protective functions not
functioning. Control output
RA
Do not connect or disconnect the connection cables between signal
each unit, the encoder cable or PLC expansion cable while the
power is ON.
Securely tighten the cable connector fixing screws and fixing mechanisms. Insufficient fixing may
lead to the cables combing off during operation.
Do not bundle the power line or cables.
(5) Trial operation and adjustment

CAUTION
Confirm and adjust the program and each parameter before operation. Unpredictable
movements may occur depending on the machine.
Extreme adjustments and changes may lead to unstable operation, so never make them.
When using the absolute position system function, on starting up, and when the Motion
controller or absolute value motor has been replaced, always perform a home position return.
A-7
(6) Usage methods
CAUTION
Immediately turn OFF the power if smoke, abnormal sounds or odors are emitted from the Motion
controller, servo amplifier or servomotor.
Always execute a test operation before starting actual operations after the program or
parameters have been changed or after maintenance and inspection.
Do not attempt to disassemble and repair the units excluding a qualified technician whom our
company recognized.
Do not make any modifications to the unit.
Keep the effect or electromagnetic obstacles to a minimum by installing a noise filter or by using
wire shields, etc. Electromagnetic obstacles may affect the electronic devices used near the
Motion controller or servo amplifier.
When using the CE Mark-compliant equipment, refer to the "EMC Installation Guidelines" (data
number IB(NA)-67339) for the Motion controllers and refer to the corresponding EMC guideline
information for the servo amplifiers, inverters and other equipment.
Use the units with the following conditions.
Conditions
Item
Q61P-A1 Q61P-A2 Q61P Q62P Q63P Q64P
+10% +10% +10% +30% +10%
100 to 120VAC 200 to 240VAC 100 to 240VAC 24VDC 100 to 120VAC /
-15% -15% -15% -35% -15%
+10%
Input power 200 to 240VAC -15%
(85 to 132VAC) (170 to 264VAC) (85 to 264VAC) (15.6 to 31.2VDC) (85 to 132VAC/
170 to 264VAC)
Input frequency 50/60Hz ±5%
Tolerable
momentary 20ms or less
power failure
A-8
(7) Corrective actions for errors
CAUTION
If an error occurs in the self diagnosis of the Motion controller or servo amplifier, confirm the
check details according to the instruction manual, and restore the operation.
If a dangerous state is predicted in case of a power failure or product failure, use a servomotor
with electromagnetic brakes or install a brake mechanism externally.
Use a double circuit construction so that the electromagnetic brake operation circuit can be
operated by emergency stop signals set externally.
Shut off with the
Shut off with servo ON signal OFF, emergency stop
alarm, electromagnetic brake signal. signal(EMG).
Servomotor
RA1 EMG
Electro-
magnetic 24VDC
brakes
If an error occurs, remove the cause, secure the safety and then resume operation after alarm
release.
The unit may suddenly resume operation after a power failure is restored, so do not go near the
machine. (Design the machine so that personal safety can be ensured even if the machine
restarts suddenly.)
(8) Maintenance, inspection and part replacement

CAUTION
Perform the daily and periodic inspections according to the instruction manual.
Perform maintenance and inspection after backing up the program and parameters for the Motion
controller and servo amplifier.
Do not place fingers or hands in the clearance when opening or closing any opening.
Periodically replace consumable parts such as batteries according to the instruction manual.
Do not touch the lead sections such as ICs or the connector contacts.
Before touching the module, always touch grounded metal, etc. to discharge static electricity from
human body. Failure to do so may cause the module to fail or malfunction.
Do not directly touch the module's conductive parts and electronic components.
Touching them could cause an operation failure or give damage to the module.
Do not place the Motion controller or servo amplifier on metal that may cause a power leakage
or wood, plastic or vinyl that may cause static electricity buildup.
Do not perform a megger test (insulation resistance measurement) during inspection.
A-9
CAUTION
When replacing the Motion controller or servo amplifier, always set the new module settings
correctly.
When the Motion controller or absolute value motor has been replaced, carry out a home position
return operation using one of the following methods, otherwise position displacement could occur.
1) After writing the servo data to the Motion controller using programming software, switch on the
power again, then perform a home position return operation.
2) Using the backup function of the programming software, load the data backed up before
replacement.
After maintenance and inspections are completed, confirm that the position detection of the
absolute position detector function is correct.
Do not drop or impact the battery installed to the module.
Doing so may damage the battery, causing battery liquid to leak in the battery. Do not use the
dropped or impacted battery, but dispose of it.
Do not short circuit, charge, overheat, incinerate or disassemble the batteries.
The electrolytic capacitor will generate gas during a fault, so do not place your face near the
Motion controller or servo amplifier.
The electrolytic capacitor and fan will deteriorate. Periodically replace these to prevent secondary
damage from faults. Replacements can be made by our sales representative.
(9) About processing of waste

When you discard Motion controller, servo amplifier, a battery (primary battery) and other option articles,
please follow the law of each country (area).
CAUTION
This product is not designed or manufactured to be used in equipment or systems in situations
that can affect or endanger human life.
When considering this product for operation in special applications such as machinery or systems
used in passenger transportation, medical, aerospace, atomic power, electric power, or
submarine repeating applications, please contact your nearest Mitsubishi sales representative.
Although this product was manufactured under conditions of strict quality control, you are strongly
advised to install safety devices to forestall serious accidents when it is used in facilities where a
breakdown in the product is likely to cause a serious accident.
(10) General cautions

CAUTION
All drawings provided in the instruction manual show the state with the covers and safety
partitions removed to explain detailed sections. When operating the product, always return the
covers and partitions to the designated positions, and operate according to the instruction manual.
A - 10
REVISIONS
The manual number is given on the bottom left of the back cover.
Print Date Manual Number Revision
Jan., 2008 IB(NA)-0300133-A First edition
Japanese Manual Number IB(NA)-0300125
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent
licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property
rights which may occur as a result of using the contents noted in this manual.
© 2008 MITSUBISHI ELECTRIC CORPORATION
A - 11
INTRODUCTION
Thank you for choosing the Mitsubishi Motion controller Q173DCPU/Q172DCPU.

Before using the equipment, please read this manual carefully to develop full familiarity with the functions
and performance of the Motion controller you have purchased, so as to ensure correct use.
CONTENTS
Safety Precautions .........................................................................................................................................A- 1

Revisions ........................................................................................................................................................A-11
Contents .........................................................................................................................................................A-12
About Manuals ...............................................................................................................................................A-15
1. OVERVIEW 1- 1 to 1- 4
1.1 Overview................................................................................................................................................... 1- 1
1.2 Differences between Q173DCPU/Q172DCPU and Q173HCPU/Q172HCPU ...................................... 1- 3
2. SYSTEM CONFIGURATION 2- 1 to 2-72
2.1 Motion System Configuration .................................................................................................................. 2- 1

2.1.1 Q173DCPU System overall configuration ........................................................................................ 2- 3
2.1.2 Q172DCPU System overall configuration ........................................................................................ 2- 5
2.1.3 Function explanation of the Q173DCPU/Q172DCPU Motion CPU modules ................................. 2- 7
2.1.4 Restrictions on Motion systems........................................................................................................ 2- 8
2.2 System Configuration Equipment............................................................................................................ 2-11
2.3 General Specifications ............................................................................................................................. 2-18
2.4 Specifications of Equipment and Settings............................................................................................... 2-19
2.4.1 Name of parts for CPU module ........................................................................................................ 2-19
2.4.2 Power supply module........................................................................................................................ 2-27
2.4.3 Base unit and extension cable.......................................................................................................... 2-35
2.4.4 Q172DLX Servo external signals interface module ......................................................................... 2-38
2.4.5 Q172DEX Synchronous encoder interface module......................................................................... 2-43
2.4.6 Q173DPX Manual pulse generator interface module ...................................................................... 2-52
2.4.7 Manual pulse generator/Serial absolute synchronous encoder ...................................................... 2-61
2.4.8 SSCNET cables and connection method...................................................................................... 2-63
2.4.9 External battery ................................................................................................................................. 2-68
2.4.10 Forced stop input terminal .............................................................................................................. 2-71
3. DESIGN 3- 1 to 3-16
3.1 System Designing Procedure .................................................................................................................. 3- 1

3.2 External Circuit Design ............................................................................................................................ 3- 4
3.2.1 Power supply circuit design .............................................................................................................. 3- 8
3.2.2 Safety circuit design .......................................................................................................................... 3- 9
3.3 Layout Design within The Control Panel ................................................................................................. 3-11
3.3.1 Mounting environment....................................................................................................................... 3-11
3.3.2 Layout design of the base units ........................................................................................................ 3-12
3.3.3 Calculating heat generation by Motion controller............................................................................. 3-13
3.4 Design Checklist ...................................................................................................................................... 3-16
A - 12
4. INSTALLATION AND WIRING 4- 1 to 4-26
4.1 Module Installation ................................................................................................................................... 4- 1

4.1.1 Instructions for handling .................................................................................................................... 4- 1
4.1.2 Instructions for mounting the base unit ............................................................................................ 4- 3
4.1.3 Installation and removal of module................................................................................................... 4- 6
4.1.4 Instructions for mounting of the battery holder unit.......................................................................... 4- 9
4.2 Connection and disconnection of Cable.................................................................................................. 4-10
4.2.1 SSCNET cable ............................................................................................................................... 4-10
4.2.2 Battery cable...................................................................................................................................... 4-13
4.2.3 Forced stop input cable..................................................................................................................... 4-15
4.3 Mounting of Serial Absolute Synchronous Encoder ............................................................................... 4-16
4.4 Wiring........................................................................................................................................................ 4-18
4.4.1 Instructions for wiring ........................................................................................................................ 4-18
4.4.2 Connecting to the power supply module .......................................................................................... 4-21
4.4.3 Precautions of SSCNET cable wiring ............................................................................................ 4-23
5. TRIAL OPERATION AND ADJUSTMENT 5- 1 to 5- 8
5.1 Checklist before Trial Operation .............................................................................................................. 5- 1

5.2 Trial Operation and Adjustment Procedure............................................................................................. 5- 3
5.3 Operating System Software Installation Procedure................................................................................ 5- 7
5.4 Trial Operation and Adjustment Checklist............................................................................................... 5- 8
6. INSPECTION AND MAINTENANCE 6- 1 to 6-28
6.1 Maintenance Works ................................................................................................................................. 6- 2

6.1.1 Instruction of Inspection works ......................................................................................................... 6- 2
6.2 Daily Inspection ........................................................................................................................................ 6- 4
6.3 Periodic Inspection................................................................................................................................... 6- 5
6.4 Life ............................................................................................................................................................ 6- 6
6.5 External Battery........................................................................................................................................ 6- 7
6.5.1 Battery life.......................................................................................................................................... 6- 8
6.5.2 Battery replacement procedure ........................................................................................................ 6-10
6.5.3 Resuming operation after storing the Motion controller ................................................................... 6-12
6.6 Troubleshooting ....................................................................................................................................... 6-13
6.6.1 Troubleshooting basics ..................................................................................................................... 6-13
6.6.2 Troubleshooting of Motion CPU module .......................................................................................... 6-14
6.6.3 Confirming error code ....................................................................................................................... 6-25
6.6.4 I/O module troubleshooting............................................................................................................... 6-26
APPENDICES App- 1 to App-17
APPENDIX 1 Cables..................................................................................................................................App- 1
APPENDIX 1.1 SSCNET cables.........................................................................................................App- 1
APPENDIX 1.2 Serial absolute synchronous encoder cable................................................................App- 4
APPENDIX 1.3 Battery cable.................................................................................................................App- 6
APPENDIX 1.4 Forced stop input cable ................................................................................................App- 7
A - 13
APPENDIX 2 Exterior Dimensions ............................................................................................................App- 8
APPENDIX 2.1 CPU module .................................................................................................................App- 8
APPENDIX 2.2 Servo external signals interface module (Q172DLX)..................................................App- 9
APPENDIX 2.3 Synchronous encoder interface module (Q172DEX)..................................................App- 9
APPENDIX 2.4 Manual pulse generator interface module (Q173DPX)...............................................App-10
APPENDIX 2.5 Power supply module (Q61P-A1, Q61P-A2, Q61P, Q62P, Q63P, Q64P).................App-11
APPENDIX 2.6 Battery holder unit (Q170DBATC) ...............................................................................App-12
APPENDIX 2.7 Connector .....................................................................................................................App-13
APPENDIX 2.8 Manual pulse generator (MR-HDP01) .........................................................................App-16
APPENDIX 2.9 Serial absolute synchronous encoder (Q170ENC) .....................................................App-16
A - 14
About Manuals
The following manuals are also related to this product.

In necessary, order them by quoting the details in the tables below.
Related Manuals
(1) Motion controller

Manual Number
Manual Name
(Model Code)
Q173DCPU/Q172DCPU Motion controller Programming Manual (COMMON)
This manual explains the Multiple CPU system configuration, performance specifications, common IB-0300134
parameters, auxiliary/applied functions, error lists and others. (1XB928)
(Optional)
Q173DCPU/Q172DCPU Motion controller (SV13/SV22) Programming Manual (Motion SFC)

IB-0300135
This manual explains the functions, programming, debugging, error lists and others for Motion SFC.
(1XB929)
(Optional)
Q173DCPU/Q172DCPU Motion controller (SV13/SV22) Programming Manual (REAL MODE)

IB-0300136
This manual explains the servo parameters, positioning instructions, device lists, error lists and others.
(1XB930)
(Optional)
Q173DCPU/Q172DCPU Motion controller (SV22) Programming Manual (VIRTUAL MODE)

This manual explains the dedicated instructions to use the synchronous control by virtual main shaft,
IB-0300137
mechanical system program create mechanical module, servo parameters, positioning instructions, device
(1XB931)
lists, error lists and others.
(Optional)
A - 15
(2) PLC
Manual Number
Manual Name
(Model Code)
QCPU User's Manual (Hardware Design, Maintenance and Inspection)
This manual explains the specifications of the QCPU modules, power supply modules, base modules, SH-080483ENG
extension cables, memory card battery and others. (13JR73)
(Optional)
QCPU User's Manual (Function Explanation, Program Fundamentals)

This manual explains the functions, programming methods and devices and others to create programs SH-080484ENG
with the QCPU. (13JR74)
(Optional)
QCPU User's Manual (Multiple CPU System)

This manual explains the functions, programming methods and cautions and others to construct the SH-080485ENG
Multiple CPU system with the QCPU. (13JR75)
(Optional)
QCPU (Q Mode)/QnACPU Programming Manual (Common Instructions)

This manual explains how to use the sequence instructions, basic instructions, application instructions and SH-080039
micro computer program. (13JF58)
(Optional)
QCPU (Q Mode)/QnACPU Programming Manual (PID Control Instructions)

SH-080040
This manual explains the dedicated instructions used to exercise PID control. (13JF59)
(Optional)
QCPU (Q Mode)/QnACPU Programming Manual (SFC)

This manual explains the system configuration, performance specifications, functions, programming, SH-080041
debugging, error codes and others of MELSAP3. (13JF60)
(Optional)
I/O Module Type Building Block User's Manual

This manual explains the specifications of the I/O modules, connector, connector/terminal block SH-080042
conversion modules and others. (13JL99)
(Optional)
(3) Servo amplifier

Manual Number
Manual Name
(Model Code)
MR-J3- B Servo amplifier Instruction Manual
This manual explains the I/O signals, parts names, parameters, start-up procedure and others for SH-030051
MR-J3- B Servo amplifier. (1CW202)
(Optional)
Fully Closed Loop Control MR-J3- B-RJ006 Servo amplifier Instruction Manual
This manual explains the I/O signals, parts names, parameters, start-up procedure and others for Fully SH-030056
Closed Loop Control MR-J3- B-RJ006 Servo amplifier. (1CW304)
(Optional)
A - 16
1 OVERVIEW
1. OVERVIEW
1.1 Overview 1
This User's Manual describes the hardware specifications and handling methods of the
Motion Controller's Model Q173DCPU/Q172DCPU for the Q series PLC Multiple CPU
system.
The Manual also describes those items related to the specifications of the option
module for the Motion controller, Manual pulse generator, Synchronous encoder and
cables.
In this manual, the following abbreviations are used.
Generic term/Abbreviation Description
Q173DCPU/Q172DCPU or
Q173DCPU/Q172DCPU Motion CPU module
Motion CPU (module)
Q172DLX Servo external signals interface module/
Q172DLX/Q172DEX/Q173DPX or (Note-1)
Q172DEX Serial Synchronous encoder interface module /
Motion module
Q173DPX Manual pulse generator interface module
MR-J3- B Servo amplifier model MR-J3- B
AMP or Servo amplifier General name for "Servo amplifier model MR-J3- B"
QCPU, PLC CPU or PLC CPU module QnUD(H)CPU
Multiple CPU system or Motion system Abbreviation for "Multiple PLC system of the Q series"
Abbreviation for "CPU No.n (n= 1 to 4) of the CPU module for the Multiple CPU
CPUn
system"
Self CPU Motion CPU being programmed by the currently open MT Developer project
Programming software package General name for MT Developer/GX Developer/MR Configurator
Operating system software General name for "SW8DNC-SV Q "
Operating system software for conveyor assembly use (Motion SFC) :
SV13
SW8DNC -SV13Q
Operating system software for automatic machinery use (Motion SFC) :
SV22
SW8DNC -SV22Q
Abbreviation for "Motion controller programming software
MT Developer
MT Developer2 (Version 1.00A or later)"
Abbreviation for "MELSEC PLC programming software package
GX Developer
GX Developer (Version 8.48A or later)"
Abbreviation for "Servo setup software package
MR Configurator
MR Configurator (Version C0 or later)"
Manual pulse generator or MR-HDP01 Abbreviation for "Manual pulse generator (MR-HDP01)"
Serial absolute synchronous encoder
Abbreviation for "Serial absolute synchronous encoder (Q170ENC)"
or Q170ENC
(Note-2) High speed synchronous network between Motion controller and servo
SSCNET
amplifier
General name for "system using the servomotor and servo amplifier for
Absolute position system
absolute position"
Battery holder unit Battery holder unit (Q170DBATC)
External battery General name for "Q170DBATC" and "Q6BAT"
Abbreviation for "MELSECNET/H module/Ethernet module/CC-Link module/
Intelligent function module
Serial communication module"
(Note-1) : Q172DEX can be used in SV22.
(Note-2) : SSCNET: Servo System Controller NETwork
1-1
1 OVERVIEW
REMARK
For information about the each module, design method for program and parameter,
refer to the following manuals relevant to each module.
Item Reference Manual

PLC CPU, peripheral devices for PLC program design,
Manual relevant to each module
I/O modules and intelligent function module
Operation method for MT Developer Help of each software
• Multiple CPU system configuration
• Performance specification Q173DCPU/Q172DCPU Motion controller
• Design method for common parameter Programming Manual (COMMON)
• Auxiliary and applied functions (common)
• Design method for Motion SFC program
Q173DCPU/Q172DCPU Motion controller
SV13/SV22 • Design method for Motion SFC parameter
(SV13/SV22) Programming Manual (Motion SFC)
• Motion dedicated PLC instruction
• Design method for positioning control
program in the real mode Q173DCPU/Q172DCPU Motion controller
• Design method for positioning control (SV13/SV22) Programming Manual (REAL MODE)
parameter
SV22 • Design method for mechanical system Q173DCPU/Q172DCPU Motion controller
(Virtual mode) program (SV22) Programming Manual (VIRTUAL MODE)
1-2
1 OVERVIEW
1.2 Differences between Q173DCPU/Q172DCPU and Q173HCPU/Q172HCPU
Items Q173DCPU Q172DCPU Q173HCPU Q173HCPU

0.44ms/ 1 to 3 axes
0.44ms/ 1 to 6 axes
0.44ms/ 1 to 6 axes 0.88ms/ 4 to 10 axes 0.44ms/ 1 to 3 axes
SV13 0.88ms/ 7 to 18 axes
0.88ms/ 7 to 8 axes 1.77ms/11 to 20 axes 0.88ms/ 4 to 8 axes
1.77ms/19 to 32 axes
Operation cycle 3.55ms/21 to 32 axes
(default) 0.44ms/ 1 to 4 axes 0.88ms/ 1 to 5 axes
0.88ms/ 5 to 12 axes 0.44ms/ 1 to 4 axes 1.77ms/ 6 to 14 axes 0.88ms/ 1 to 5 axes
SV22
1.77ms/13 to 28 axes 0.88ms/ 5 to 8 axes 3.55ms/15 to 28 axes 1.77ms/ 6 to 8 axes
3.55ms/29 to 32 axes 7.11ms/29 to 32 axes
Medium of operating system
CD-ROM (1 disk) FD (2 disks)
software
Model of operating system
SW8DNC-SV Q SW6RN-SV Q
software
Peripheral I/F Via PLC CPU (USB/RS-232) USB/SSCNET
Multiple CPU high speed main base unit Main base unit
Main base unit
(Q38DB/Q312DB) (Q33B/Q35B/Q38B/Q312B)
Color of base cover Gray Clear
Mount it unit by unit fixing screws when using system
Mounting on panel Be sure to mount it by unit fixing screws.
in a place where the vibration or impact is large.
DIN rail Unusable Usable
CPU module No.1 QnUD(H)CPU Qn(H)CPU
Installation orders CPU No.2 Install Motion CPU modules on the right-hand side of
No restriction
or later PLC CPU module.
CPU empty slot Settable between CPU modules Not settable between CPU modules
PLC CPU module Universal model (QnUD(H)CPU) High performance model (Qn(H)CPU)
Motion CPU module Q173DCPU/Q172DCPU Q173HCPU(-T)/Q172HCPU(-T)
Combination of Motion
Q173DCPU/Q172DCPU only Combination with Q173CPUN(T)/Q172CPUN(-T)
CPU modules
Install Motion CPU modules by unit fixing screws
Installation on main base Be sure to install Motion CPU modules by unit fixing
when using them in a place where the vibration or
unit screws.
impact is large.
Function select switch Rotary switch 1, Rotary switch 2 Dip switch 1 to 5
RESET/L.CLR switch None Provided
Each LED of MODE, RUN, ERR, M.RUN, BAT and
LED indication 7-segment LED display
BOOT
Add Q6BAT at continuous power failure for 1 month
External battery Demand
or more
Battery holder unit Q170DBATC Q170HBATC
• Use EMI terminal of Motion CPU module
• Use device set by forced stop input setting in the
Forced stop input • Use device set by forced stop input setting in the
system setting.
system setting.
Cable for forced stop input Demand —
Motion module Q172DLX/Q172DEX/Q173DPX Q172LX/Q172EX/Q173PX
Installation on main base
Impossible to install on I/O slots of 0 to2 Possible to install on I/O slots of 0 to2
unit
Multiple CPU high speed
transmission memory for data
Included —
transfer between CPU
modules
1-3
1 OVERVIEW
MEMO
1-4
2 SYSTEM CONFIGURATION
2. SYSTEM CONFIGURATION
This section describes the Q173DCPU/Q172DCPU system configuration, precautions
on use of system and configured equipments.
2.1 Motion System Configuration
2
(1) Equipment configuration in Q173DCPU/Q172DCPU system
Extension of the Q series module
(Note-2)
Power supply module/

QnUD(H)CPU/ I/O module/ Motion module
Intelligent function module (Q172DLX, Q173DPX)
of the Q series
Motion module Main base unit Extension cable Q6 B extension base unit
(Q172DLX, Q172DEX, Q173DPX) (Q38DB, Q312DB) (QC B) (Q63B, Q65B, Q68B, Q612B)
(Note-1)
Power supply module/

Battery holder unit Motion CPU module Forced stop input cable I/O module/Intelligent function
(Q170DBATC) (Q173DCPU/Q172DCPU) (Q170DEMICBL M) module of the Q series
(Note-1)
MITSUBISHI
LITHIUM BATTERY
Battery SSCNET cable

(Q6BAT) (MR-J3BUS M(-A/-B))
Servo amplifier
(MR-J3- B)
It is possible to select the best according to the system.

(Note-1) : Be sure to install the Battery (Q6BAT) to the Battery holder unit (Q170DBATC).
It is packed together with Q173DCPU/Q172DCPU.
(Note-2) : Q172DEX cannot be used in the extension base unit.
Install it to the main base unit.
2-1
(2) Peripheral device configuration for the Q173DCPU/Q172DCPU

The following (a)(b) can be used.
(a) USB configuration (b) RS-232 configuration
PLC CPU module PLC CPU module

(QnUD(H)CPU) (QnUD(H)CPU)
RS-232 communication cable

USB cable
(QC30R2)
MIT SUBISHI MIT SUBISHI
Personal computer Personal computer
2-2
2.1.1 Q173DCPU System overall configuration
Motion CPU control module
interface module
interface module
interface module
Servo external
Manual pulse
Synchronous
generator
encoder
signals
PLC CPU/
Motion CPU
Main base unit
(Q3 DB) Q61P QnUD(H) Q173D QI60 QX Q6 AD Q172D Q172D Q173D
CPU CPU LX EX PX
QY Q6 DA I/O module/
100/200VAC
Manual pulse generator 3/module

P
(MR-HDP01) (Up to 1 module)
Serial absolute synchronous encoder cable

USB/RS-232
(Q170ENCCBL M)
Serial absolute synchronous encoder 2/module
E
(Q170ENC) (Up to 6 modules)
Personal Computer
IBM PC/AT External input signals Number of Inputs
FLS : Upper stroke limit
RLS : Lower stroke limit 8 axes/module
STOP : Stop signal (Up to 4 modules)
DOG/CHANGE : Proximity dog/
Speed-position switching
Battery holder unit

Q170DBATC Analogue input/output
Input/output (Up to 256 points)
Interrupt signals (16 points)

Forced stop input cable
(Q170DEMICBL M)
Extension base unit EMI forced stop input (24VDC)

(Q6 B)
SSCNET cable
Power supply
(MR-J3BUS M(-A/-B)) SSCNET (CN1)

module
Extension cable
(QC B) SSCNET (CN2) d1 d16 d1 d16
UP to 7 extensions
M M M M
E E E E
MR-J3- B model Servo amplifier,

Up to 32 axes (Up to 16 axes/system)
External input signals of servo amplifier
Proximity dog
Upper stroke limit
Lower stroke limit
2-3
CAUTION
operation of the Motion controller or servo amplifier differ from the safety directive operation in
the system.
servomotor.
2-4
2.1.2 Q172DCPU System overall configuration
Motion CPU control module
interface module
interface module
interface module
Servo external
Manual pulse
Synchronous
generator
encoder
signals
PLC CPU/
Motion CPU
Main base unit
(Q3 DB) Q61P QnUD(H) Q172D QI60 QX Q6 AD Q172D Q172D Q173D
CPU CPU LX EX PX
QY Q6 DA I/O module /
100/200VAC
Manual pulse generator 3/module

P
(MR-HDP01) (Up to 1 module)

USB/RS-232
(Q170ENCCBL M)
Serial absolute synchronous encoder 2/module
E
(Q170ENC)(Up to 6 modules)
Personal Computer
IBM PC/AT External input signals Number of Inputs
FLS : Upper stroke limit
RLS : Lower stroke limit 8 axes/module
STOP : Stop signal (Up to 4 modules)
DOG/CHANGE : Proximity dog/
Speed-position switching
Battery holder unit

Q170DBATC Analogue input/output
Input/output (Up to 256 points)
Interrupt signals (16 points)
Forced stop input cable

(Q170DEMICBL M)
Extension base unit
(Q6 B) EMI forced stop input (24VDC)
Power supply
SSCNET cable
(MR-J3BUS M(-A/-B))
module
Extension cable
(QC B)
SSCNET (CN1) d1 d2 d3 d8
UP to 7 extensions
M M M M
E E E E
MR-J3- B model Servo amplifier,

Up to 8 axes
External input signals of servo amplifier
Proximity dog
Upper stroke limit
Lower stroke limit
2-5
CAUTION
the system.
servomotor.
2-6
2.1.3 Function explanation of the Q173DCPU/Q172DCPU Motion CPU modules
(1) Up to 32 axes servo amplifiers per 2 systems (up to 16 axes per 1 system) can be
used in Q173DCPU. Up to 8 axes servo amplifiers per 1 system can be used in
Q172DCPU.
(2) It is possible to set the program which synchronized with the motion operation
cycle and executed at fixed cycle (0.88[ms], 1.77[ms], 3.55[ms], 7.11[ms],
14.2[ms]).
(3) It is possible to execute a download of servo parameters to servo amplifier, servo

ON/OFF to servo amplifier and position commands, etc. by connecting between
the Q173DCPU/Q172DCPU and servo amplifier with SSCNET cable.
(4) It is possible to select the servo control functions/programming languages by

installing the corresponding operating system software in the Q173DCPU/
Q172DCPU.
(5) Motion modules (Q172DLX/Q172DEX/Q173DPX) are controlled with the

Q173DCPU/Q172DCPU, and the signals such as stroke limit signals connected to
Motion modules and synchronous encoder are used as motion control.
(6) PLC I/O modules can be controlled with the Q173DCPU/Q172DCPU.

(Refer to Section 2.2 (2) for PLC I/O modules that can be controlled with Motion
CPU.)
(7) Data exchange between CPU modules is possible by Multiple CPU high speed
transmission memory or automatic refresh in the Multiple CPU system.
2-7
2.1.4 Restrictions on Motion systems
(1) Combination of Multiple CPU system

(a) Motion CPU module cannot be used as standalone module.
Be sure to install the universal model PLC CPU module (Q03UDCPU/
Q04UDHCPU/Q06UDHCPU) to CPU No.1.
For Universal model PLC CPU module, "Multiple CPU high speed
transmission function" must be set in the Multiple CPU settings.
(b) Only Multiple CPU high speed main base unit (Q38DB/Q312DB) can be
used.
(c) The combination of Q173DCPU/Q172DCPU and Q173HCPU(-T)/

Q172HCPU(-T)/Q173CPUN(-T)/Q172CPUN(-T) cannot be used.
(d) Up to four modules of PLC CPU modules (Q03UDCPU/Q04UDHCPU/

Q06UDHCPU/Motion CPU modules can be installed from the CPU slot (the
slot on the right side of power supply module) to slot 2 of the main base unit.
CPU modules called as CPU No.1 to CPU No.4 from the left sequentially.
There is no restriction on the installation order of CPU No.2 to No.4.
For CPU module except CPU No.1, an empty slot can be reserved for
addition of CPU module. An empty slot can be set between CPU modules.
However, the installation condition when combining with the High
performance PLC CPU module/Process CPU module/PC CPU module/C
controller module is different depending on the specification of CPU
modules, refer to the Manuals of each CPU modules.
(e) It takes about 10 seconds to startup (state that can be controlled) of Motion
CPU. Make a Multiple CPU synchronous startup setting suitable for the
system.
(f) Execute the automatic refresh of the Motion CPU modules and PLC CPU
modules (Q03UDCPU/Q04UDHCPU/Q06UDHCPU) by using the automatic
refresh of Multiple CPU high speed transmission area setting.
When the High performance PLC CPU module/Process CPU module/PC
CPU module/C controller module is installed in the combination of Multiple
CPU system, the Motion CPU module cannot be execute the automatic
refresh with these modules.
(g) Use the Motion dedicated PLC instructions that starts by "D(P).". The Motion
dedicated PLC instructions that starts by "S(P)." cannot be used. When the
High performance PLC CPU module/Process CPU module/PC CPU
module/C controller module is installed in the combination of Multiple CPU
system, the Motion dedicated PLC instruction from these modules cannot be
executed.
2-8
(2) Motion modules

(Note-1)
(a) Installation position of Q172DEX is only the main base unit.
It cannot be used on the extension base unit.
(b) Q172DLX/Q173DPX can be installed on any of the main base unit/

extension base unit.
(Note-1)
(c) Q172DLX/Q172DEX /Q173DPX cannot be installed in CPU slot and I/O
slot 0 to 2 of the main base unit. Wrong installation might damage the main
base unit.
(d) Q172EX(-S1/-S2/-S3)/Q172LX/Q173PX(-S1) for Q173HCPU(-T)/

Q172HCPU(-T)/Q173CPUN(-T)/Q172CPUN(-T)/Q173CPU/Q172CPU
cannot be used.
(e) Be sure to use the Motion CPU as the control CPU of Motion modules
(Note-1)
(Q172DLX, Q172DEX , Q173DPX, etc.) for Motion CPU. They will not
operate correctly if PLC CPU is set and installed as the control CPU by
mistake. Motion CPU is treated as a 32-point intelligent module by PLC
CPU of other CPU.
(Note-1) : Q172DEX can be used in SV22. It cannot be used in SV13.
2-9
(3) Other restrictions

(a) Motion CPU module cannot be set as the control CPU of intelligent function
module (except some modules) or Graphic Operation Terminal(GOT).
(b) Be sure to use the external battery.
(c) There are following methods to execute the forced stop input.
• Use a EMI terminal of Motion CPU module
• Use a device set in the forced stop input setting of system setting
(d) Forced stop input for EMI terminal of Motion CPU module cannot be
invalidated by the parameter.
When the device set in the forced stop input setting is used without use of
EMI terminal of Motion CPU module, apply 24VDC voltage on EMI terminal
and invalidate the forced stop input of EMI terminal.
(e) Be sure to use the cable for forced stop input (sold separately). The forced
stop cannot be released without using it.
(f) When the operation cycle is 0.4[ms], set the system setting as the axis select
switch of servo amplifier "0 to 7".
If the axis select switch of servo amplifier "8 to F" is set, the servo amplifiers
are not recognized.
(g) When a Multiple CPU system is configured, make sure to configure the
modules so that the total current consumption of individual modules on the
main base does not exceed the 5VDC output capacity of power supply
module.
(Refer to Section 2.4.2 (3) "Selection of the power supply module".)
(h) It is impossible to mount the main base unit by DIN rail when using the
Motion CPU module.
Doing so could result in vibration that may cause erroneous operation.
(i) The module name displayed by "System monitor" - "Product information list"
of GX Developer is different depending on the function version of Motion
modules (Q172DLX, Q172DEX, Q173DPX).
(Note): Even if the function version "C" is displayed, it does not correspond
to the online module change.
Model display
Module name
Function version "B" Function version "C"
Q172DLX Q172LX Q172DLX
Q172DEX MOTION-UNIT Q172DEX
Q173DPX MOTION-UNIT Q173DPX
2 - 10
2.2 System Configuration Equipment
(1) Table of Motion controller related module

Current
Part name Model name (Note-1) Description consumption Remark
5VDC[A]
Up to 32 axes control, Operation cycle 0.44[ms] or more
Q173DCPU 1.25
(Attachment battery holder unit and battery (Q6BAT))
Motion CPU module
Up to 8 axes control, Operation cycle 0.44[ms] or more
Q172DCPU 1.25
(Attachment battery holder unit and battery (Q6BAT))
Servo external
Servo external signal input 8 axes
signals Q172DLX 0.06
(FLS, RLS, STOP, DOG/CHANGE×8)
interface module
Synchronous
Serial absolute synchronous encoder Q170ENC interface×2,
encoder interface Q172DEX 0.19
Tracking input 2 points
module
Manual pulse
Manual pulse generator MR-HDP01/Incremental synchronous encoder
generator Q173DPX 0.38
interface ×3, Tracking input 3 points
interface module
Q03UDCPU Program capacity 30k steps, LD instruction processing speed 20[ns] 0.33
PLC CPU module
(Note-2) Q04UDHCPU Program capacity 40k steps, LD instruction processing speed 9.5[ns] 0.39
Q06UDHCPU Program capacity 60k steps, LD instruction processing speed 9.5[ns] 0.39
Q61P-A1 100 to 120VAC input, 5VDC 6A output
Q61P-A2 200 to 240VAC input, 5VDC 6A output
Power supply Q61P 100 to 240VAC input, 5VDC 6A output
——
module (Note-3) Q62P 100 to 240VAC input, 5VDC 3A/24VDC 0.6A output
Q63P 24VDC input, 5VDC 6A output
Q64P 100 to 120VAC/200 to 240VAC input, 5VDC 8.5A output
Q38DB Multiple CPU high speed bus (4 slots), Number of I/O modules : 8 slots 0.228
Main base unit
Q312DB Multiple CPU high speed bus (4 slots), Number of I/O modules : 12 slots 0.233
Q63B Number of I/O modules installed 3 slots 0.105
Extension base unit
QC05B Length 0.45m(1.48ft.)
Extension cable ——
QC30B Length 3m(9.84ft.)
Resolution: 262144PLS/rev
Serial absolute
Permitted axial loads Radial load: Up to 19.6N
synchronous Q170ENC 0.20
Thrust load: Up to 9.8N
encoder
Permitted speed: 3600r/min
Serial absolute Serial absolute synchronous encoder Q170ENC Q172DEX
synchronous Q170ENCCBL M 2m(6.56ft.), 5m(16.40ft.), 10m(32.81ft.), 20m(65.62ft.), 30m(98.43ft.), ——
encoder cable 50m(164.04ft.)
2 - 11
Table of Motion controller related module(continued)

Current
5VDC[A]
Q172DEX side connector
Connector set for Connector :10120-3000PE
serial absolute Connector case : 10320-52F0-008
Q170ENCCNS ——
synchronous Q170ENC side connector
encoder cable Plug : MS3106B22-14S
Cable clump : MS3057-12A
Pulse resolution: 25PLS/rev(100PLS/rev after magnification by 4)
Manual pulse Permitted axial loads Radial load: Up to 19.6N
MR-HDP01 0.06
generator Thrust load: Up to 9.8N
Permitted speed: 200r/min(Normal rotation), Voltage output
Battery holder
Q170DBATC Battery holder for Q6BAT (Attachment battery cable) ——
unit (Note-4)
For memory data backup of SRAM built-in Motion CPU
Q6BAT
Battery (Programs, Parameters, Absolute position data, Latch data) ——
A6BAT For data backup of Q170ENC
Cable for forced Length 0.5m(1.64ft), 1m(3.28ft), 3m(9.84ft), 5m(16.40ft), 10m(32.80ft),
Q170DEMICBL M ——
stop input (Note-5) 15m(49.20ft), 20m(65.62ft), 25m(82.02ft), 30m(98.43ft)
For positive common sink type input module, sink type output module
A6TBXY36 ——
Connector/terminal (standard type)
block conversion For positive common sink type input module, sink type output module
A6TBXY54 ——
module (Note-6) (2-wire type)
A6TBX70 For positive common sink type input module (3-wire type) ——
AC05TB Length 0.5m (1.64ft.) ——
AC10TB Length 1m (3.28ft.) ——
Cable for
connector/terminal
block conversion
module
AC100TB Length 10m(32.81ft.) ——
2 - 12
Table of Motion controller related module(continued)

Current
5VDC[A]
• Q173DCPU/Q172DCPU MR-J3- B
• MR-J3- B MR-J3- B
MR-J3BUS M ——
• Standard code for inside panel
• 0.15m(0.49ft.), 0.3m(0.98ft.), 0.5m(1.64ft.), 1m(3,28ft.), 3m(9.84ft.)
• MR-J3- B MR-J3- B
SSCNET cable MR-J3BUS M-A ——
• Standard cable for outside panel
• 5m(16.40ft.), 10m(32.81ft.), 20m(65.62ft.)
(Note-7) • MR-J3- B MR-J3- B
MR-J3BUS M-B ——
• Long distance cable
• 30m(98.43ft.), 40m(131.23ft.), 50m(164.04ft.)
(Note-1) : =Cable length (015: 0.15m(0.49ft.), 03: 0.3m(0.98ft.), 05: 0.5m(1.64ft.), 1: 1m(3.28ft.), 2: 2m(6.56ft.),
3: 3m(9.84ft.), 5: 5m(16.40ft.), 10: 10m(32.81ft.), 20: 20m(65.62ft.), 25: 25m(82.02ft.), 30:
30m(98.43ft.), 40: 40m(131.23ft.), 50:50m(164.04ft.)
(Note-2) : 5VDC internal current consumption of shared equipments with PLC might be changed.
Be sure to refer to the PLC Manuals.
(Note-3) : Be sure to use the power supply module within the range of power supply capacity.
(Note-4) : Battery Q6BAT is not attached to Battery holder unit Q170DBATC. Please purchase it separately.
(Note-5) : Be sure to use the cable for forced stop input (sold separately). The forced stop cannot be released
without using it.
Cable for forced stop input is not attached to the Motion CPU module. Please purchase the cable for
length according to system separately.
(Note-6) : These modules can be used in Q172DLX. It cannot be controlled using Q173DPX.
(Note-7) : Please contact your nearest Mitsubishi sales representative for the cable of less than 30m(98.43ft.).
2 - 13
(2) PLC module which can be control by Motion CPU

Current consumption
Part name Model name Description Remark
5VDC[A] (Note-1)
AC QX10 100-120VAC, 7-8mA, 16 points, Terminal block 0.05
QX40 24VDC/4mA, Positive common, 16 points, Terminal block 0.05
0.075 (Note-2)
QX41 24VDC/4mA, Positive common, 32 points, Connector
(TYP, All points ON)
0.09 (Note-2)
QX42 24VDC/4mA, Positive common, 64 points, Connector
12VDC/5V, Positive common/Negative common shared, 0.055
QX70
Input 16 points, Terminal block (TYP, All points ON)
module DC 12VDC/5V, Positive common/Negative common shared, 0.07
QX71
32 points, Terminal block (TYP, All points ON)
12VDC/5V, Positive common/Negative common shared, 0.085
QX72
64 points, Terminal block (TYP, All points ON)
0.05
QX80 24VDC/4mA, Negative common, 16 points, Terminal block
0.075 (Note-2)
QX81 24VDC/4mA, Negative common, 32 points, Connector
Contact output 240VAC/24VDC, 2A/point, 8A/common, 0.43
QY10
module 16 points/common, Terminal block (TYP, All points ON)
12V/24VDC, 0.1A/point, 1.6A/common, 16 points/common, 0.065
QY40P
Terminal block (TYP, All points ON)
12V/24VDC, 0.1A/point, 2A/common, 32 points/common, 0.105 (Note-2)
QY41P
Sink Connector (TYP, All points ON)
Type 12V/24VDC, 0.1A/point, 2A/common, 0.15
Transistor
(Note-2)
QY42P
64 points(32 points/common), Connector (TYP, All points ON)
Output 12V/24VDC, 0.5A/point, 4A/common, 0.08
QY50
module 16 points(16 points/common), Terminal block (TYP, All points ON)
12V/24VDC, 0.5A/point, 4A/common, 0.08
QY80
Source 16 points(16 points/common), Terminal block (TYP, All points ON)
Type 12V/24VDC, 0.1A/point, 2A/common, 0.095 (Note-2)
QY81P
32 points(32 points/common), Connector (TYP, All points ON)
5/12VDC, 16mA/point, 16 points(16 points/common), 0.095
QY70
TTL•CMOS Terminal block (TYP, All points ON)
(Sink) 5/12VDC, 16mA/point, 32 points(32 points/common), 0.15 (Note-2)
QY71
Connector (TYP, All points ON)
24VDC Positive common: 32 points
DC12-24V/0.1A Output Sink type: 32 points, Connector, 0.13 (Note-2)
QH42P
Provided (Thermal protectors, protector against short (TYP, All points ON)
Input/Output DC Input/
circuit)
composite Transistor
24VDC Positive common: 8 points
module output
DC12-24V/0.5A Output Sink type: 7 points, Terminal block, 0.08
QX48Y57
Provided (When face is broken, LED lights and signal is (TYP, All points ON)
output to CPU)
0.06
Interrupt module QI60 DC24V/4mA, Positive common, 16 points, Terminal block
2 - 14
Current consumption
Part name Model name Description Remark
5VDC[A] (Note-1)
2ch, A/D conversion, (Note-2)
Q62AD-DGH 0.33
Current input (Channel-isolated • High resolution)
Q64AD 4ch, A/D conversion, Voltage • Current input 0.63
4ch, A/D conversion, (Note-2)
Q64AD-GH 0.89
Voltage • Current input (Channel-isolated • High resolution)
Q68ADV 8ch, A/D conversion, Voltage input 0.64
Analogue module Q68ADI 8ch, A/D conversion, Current input 0.64
Q62DA 2ch, D/A conversion, Voltage • Current output 0.33
2ch, D/A conversion, (Note-2)
Q62DA-FG 0.37
Voltage • Current output (Channel-isolated)
Q64DA 4ch, D/A conversion, Voltage • Current output 0.34
Q68DAV 8ch, D/A conversion, Voltage output 0.39
Q68DAI 8ch, D/A conversion, Current output 0.38
(Note-1) : 5VDC internal current consumption of shared equipments with PLC might be changed.
Be sure to refer to the PLC Manuals.
(Note-2) : Connectors are not provided.
2 - 15
(3) Table of servo amplifier

Part name Model name Description
MR-J3 series MR-J3- B
Refer to catalogue of the servo amplifier.
servo amplifier MR-J3- B-RJ006
Battery MR-J3BAT Back-up for the absolute position detection
(4) Software packages

(a) Operating system software
Software package
Application
Q173DCPU Q172DCPU
For conveyor assembly SV13 SW8DNC-SV13QB SW8DNC-SV13QD
For automatic machinery SV22 SW8DNC-SV22QA SW8DNC-SV22QC
(b) Motion controller programming software

Part name Model name Details
Conveyor Assembly Software
Automatic Machinery Software
Cam Data Creation Software
SW1DNC-MTW2-E Digital Oscilloscope Software
MT Developer2
(1 CD-ROM disk) Communication System Software
Document Print Software
Operation Manual (Help)
Installation manual (PDF)
R R R
(Note) : Operating environment to use MT Developer is Windows Vista/Windows XP/Windows 2000
English version only.
(5) Operating environment of personal computer

Operating environment is shown below.
R R R
IBM PC/AT with which Windows Vista/Windows XP/Windows 2000 English
version operates normally.
Item Operating environment
R R
Microsoft Windows Vista Home Basic
R R
Microsoft Windows Vista Home Premium
R R
Microsoft Windows Vista Business
R R
Microsoft Windows Vista Ultimate
OS R R
Microsoft Windows Vista Enterprise
R R
Microsoft Windows XP Professional (Service Pack 2 or later)
R R
Microsoft Windows XP Home Edition (Service Pack 2 or later)
R R
Microsoft Windows 2000 Professional (Service Pack 4 or later)
R R
Desktop PC: Recommended Intel Celeron Processor 2.8GHz or more
CPU R R
Laptop PC: Recommended Intel Pentium Processor M 1.7GHz or more
Memory capacity Recommended 512MB or more
R R
Video card Card compatible with Microsoft DirectX 9.0c or later
Available hard disk Installation: HD 1GB or more
capacity Operation: Virtual memory 50MB or more
Disk drive CD-ROM disk drive
Display Resolution 1024×768 pixels or higher
(Note-1) : Microsoft, Windows and DirectX are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
(Note-2) : Intel, Celeron and Pentium are trademarks of Intel Corporation in the U.S. and other countries.
2 - 16
(6) Related software packages

(a) PLC software package
Model name Software package
GX Developer SW8D5C-GPPW-E
(b) Servo set up software package

Model name Software package
MR Configurator MRZJW3-SETUP221E
POINTS
(1) When the operation of Windows is not unclear in the operation of this software,
refer to the manual of Windows or guide-book from the other supplier.
(2) The following functions cannot be used when the computer is running under
R R R
Windows Vista, Windows XP or Windows 2000.
This product may not perform properly, when these functions are used.
R R
< Windows Vista/Windows XP>
R
• Activating the application with Windows compatibility mode
• Fast user switching
• Remote desktop
• Large size
R
• x64 Edition (64 bit Windows )
R
< Windows 2000>
• Large fonts
2 - 17
2.3 General Specifications
General specifications of Q173DCPU/Q172DCPU module are shown below.
Item Specification
Operating ambient temperature 0 to 55°C (32 to 131°F)
Storage ambient temperature -25 to 75°C (-13 to 167°F) (Note-3)
Operating ambient humidity 5 to 95% RH, non-condensing
Storage ambient humidity 5 to 95% RH, non-condensing
Frequency Acceleration Amplitude Sweep count
0.075mm
Under intermittent 10 to 57Hz ——
(0.003inch) 10 times each
Vibration resistance vibration 2
57 to 150Hz 9.8m/s —— in X, Y, Z
0.035mm directions
Under continuous 10 to 57Hz ——
(0.001inch) (For 80 min.)
vibration 2
57 to 150Hz 4.9m/s ——
2
Shock resistance 147m/s , 3 times in each of 3 directions X, Y, Z
Operating ambience No corrosive gases
Operating altitude 2000m(6561.68ft.) or less
Mounting location Inside control panel
Overvoltage category (Note-1) II or less
Pollution level (Note-2) 2 or less
(Note-1) : This indicates the section of the power supply to which the equipment is assumed to be connected between the
public electrical power distribution network and the machinery within premises.
Category applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the rated voltage of 300V is 2500V.
(Note-2) : This index indicates the degree to which conductive material is generated in terms of the environment in which
the equipment is used.
Pollution level 2 is when only non-conductive pollution occurs. A temporary conductivity caused by condensing
must be expected occasionally.
(Note-3) : Do not use or store the Motion controller under pressure higher than the atmospheric pressure of altitude 0m.
Doing so can cause an operation failure.
CAUTION
The Motion controller must be stored and used under the conditions listed in the table of
specifications above.
When not using the module for a long time, disconnect the power line from the Motion controller
or servo amplifier.
Place the Motion controller and servo amplifier in static electricity preventing vinyl bags and store.
When storing for a long time, please contact with our sales representative.
Also, execute a trial operation.
2 - 18
2.4 Specifications of Equipment and Settings
2.4.1 Name of parts for CPU module
This section explains the names and setting of the module.
(1) Q173DCPU/Q172DCPU
Front face of Q172DCPU Front face of Q173DCPU
Q172DCPU Q173DCPU
1) 1)
F01 F01 F01 F01
SW SW
2) 3) 2) 3)
AB E
AB E
AB E
AB E
23 6
23 6
23 6
23 6
CD
CD
CD
CD
45
45
45
45
1 2 1 2
789 789 789 789
STOP RUN STOP RUN

4) CAUTION 4) CAUTION
EMI EMI
5) 5)
6) 6)
CN1
CN1
7)
CN2
FRONT FRONT
BAT BAT
8) 8)
Side face Bottom
9)
10)
(Note) 12)
11)
(Note): Unusable
(Under manufacturer test)
2 - 19
No. Name Application

1) 7-segment LED • Indicates the operating status and error information.
Rotary function select 1 switch • Set the operation mode.
2)
(SW1) (Normal operation mode, Installation mode, Mode operated by ROM, etc)
Rotary function select 2 switch • Each switch setting is 0 to F.
3)
(SW2) (Shipped from the factory in SW1 "A", SW2 "0" position)
Move to RUN/STOP (Shipped from the factory in STOP position)
4) RUN/STOP switch RUN : Motion SFC program is started.
STOP : Motion SFC program is stopped.
Forced stop input (EMI) (Note-1) • Input to stop all axes of servo amplifier in a lump
EMI
EMI ON (opened) : Forced stop
5) EMI OFF (24VDC input) : Forced stop release
EMI.COM
EMI
6) SSCNET CN1 connector (Note-2) Connector to connect the servo amplifier of system 1 (up to 16 axes)
SSCNET CN2 connector
7) Connector to connect the servo amplifier of system 2 (up to 16 axes)
(Note-2), (Note-3)
8) Module loading lever Used to install the module to the base unit
9) Module fixing hook (Note-4) Hook used to fix the module to the base unit. (Auxiliary use for installation)
10) Module fixing screw Screw used to fix to the base unit. (M3×13)
11) Module fixing latch Hook used to fix to the base unit.
12) Battery connector (BAT) (Note-5) Connector to connect the battery holder unit Q170DBATC
(Note-1) : Be sure to use the cable for forced stop input. The forced stop cannot be released without using it.
If the cable for forced stop input is fabricated on the customer side, make it within 30m(98.43ft.).
(Note-2) : Put the SSCNET cable in the duct or fix the cable at the closest part to the Motion CPU module with bundle
material in order to prevent SSCNET cable from putting its own weight on SSCNET connector.
(Note-3) : Q173DCPU only
(Note-4) : This screw is auxiliary use for module installation to the main base unit. Be sure to fix modules to the main base
unit using supplied fixing screws.
(Note-5) : Be sure to use the external battery. The programs, parameters, absolute position data, and latch data of SRAM
built-in Motion CPU module are backed up if the battery cable is not set correctly.
2 - 20
(2) 7-segment LED display

The LED displays/flashes in the combination with errors.
Item 7-segment LED Remark
It takes about 10 seconds to initialize

Start Initializing
(RUN/STOP display).
Normal " " remains flashing Normal operation
Steady "INS" display, Mode to install the operating system

Installation mode
" " remains flashing software via personal computer.
Mode to operate based on the user
Mode operated by
" " remains flashing programs and parameters stored in the
RAM
SRAM built-in Motion CPU module.
Operation
Mode to operate after the user programs
mode
Mode operated by Steady "INS" display, and parameters stored in the FLASH
ROM " " remains flashing ROM built-in Motion CPU are read to the
SRAM built-in Motion CPU.
STOP Steady "STP" display Stopped the Motion SFC program.
RUN Steady "RUN" display Executed the Motion SFC program.
Early stage warning Displayed at battery voltage 2.7V or less.

Steady "BT1" display
Battery (2.7V or less) Refer to Section "6.5 External Battery".
error Final stage warning Displayed at battery voltage 2.5V or less.
Steady "BT2" display
(2.5V or less) Refer to Section "6.5 External Battery".
It becomes the status of installation mode
Operating system software
"A00" remains flashing when the operating system software is
not installed
not installed.
System setting error of the Motion CPU

" AL" flashes 3 times
Refer to the "Q173DCPU/Q172DCPU
System setting error
Motion controller Programming Manual
Steady " L01" display
(COMMON)" for details.
Servo error of the Motion CPU

" AL" flashes 3 times Motion controller (SV13/SV22)
Servo error Programming Manual (REAL MODE)" or
Steady " S01" display "Q173DCPU/Q172DCPU Motion
controller (SV22) Programming Manual
(VIRTUAL MODE)" for details.
H/W fault or S/W fault
Motion controller (SV13/SV22)
WDT error Steady "..." display Programming Manual (REAL MODE)" or
"Q173DCPU/Q172DCPU Motion
controller (SV22) Programming Manual
(VIRTUAL MODE)" for details.
2 - 21
Item 7-segment LED Remark
" AL" flashes 3 times
Setting error of the Multiple CPU system

Steady " A1" display
Self diagnostic error
Motion controller Programming Manual
4-digits error code is
(COMMON)" for details.
displayed in two sequential
flashes of 2-digits each.
POINTS
(1) An error is displayed at the 7-segment LED, confirm the error number etc. using
MT Developer.
(2) Refer to the Motion CPU error batch monitor of MT Developer or error list of
Programming Manual for error details.
(3) Rotary switch assignment

(a) Rotary function select 1 switch (SW1)
(Note)
Rotary switch Setting Mode Description
F0 1 0 Normal mode Normal operation mode

AB E
23
CD
4 56
789 Installed the operating system software using

A Installation mode
MT Developer
(Note): Not to be set except above setting.
(b) Rotary function select 2 switch (SW2)

(Note)
Rotary switch Setting Mode Description
Normal operation mode
0 Mode operated by RAM (Operation by the setting data and parameters
F0 1 stored in the SRAM built-in Motion CPU module.)
AB E
23
CD
Mode to operate based on the setting data and

4 56
78 9
6 Mode operated by ROM parameters wrote to the FLASH ROM built-in
Motion CPU module.
C SRAM clear SRAM "0" clear
(Note): Not to be set except above setting.
CAUTION
Be sure to turn OFF the Multiple system power supply before the rotary switch setting change.
2 - 22
(4) Operation mode

(a) Rotary switch setting and operation mode
(Note)
Rotary switch setting
Operation mode
SW1 SW2
A Any setting (Except C) Installation mode
0 0 Mode operated by RAM
0 6 Mode operated by ROM
(Note)
Any setting C SRAM clear
(Note) : The programs, parameters, absolute position data, and latch data built-in Motion
CPU module are cleared.
(b) Operation mode overview

Operation mode 7-segment LED Operation overview
• Steady "INS" display at the 7-segment LED.
• Operating system software can be installed.
Installation mode • It is STOP status regardless of the RUN/STOP switch position at the front side
of Motion CPU module.
• Digital oscilloscope function cannot be used.
• " . " remains flashing in the first digit of 7-segment LED.
Mode operated by
• It operates based on the user programs and parameters stored in the SRAM
RAM
built-in Motion CPU module.
• " . " remains flashing in the first digit and steady " . " display in the second
digit of 7-segment LED.
• Operation starts after the user programs and parameters stored in the FLASH
ROM built-in Motion CPU module are read to the SRAM built-in Motion CPU
module at power supply on or reset of the Multiple CPU system.
If the ROM writing is not executed, even if the user programs and parameters
Mode operated by
are changed using the MT Developer during mode operated by ROM,
ROM
operation starts with the contents of the FLASH ROM at next power supply on
or reset.
Also, If the ROM writing is not executed, even if the auto tuning data are
reflected on the servo parameter of Motion CPU by operation in the auto-tuning
setting, operation starts with the contents of the FLASH ROM at next power
supply on or reset.
POINTS
Be sure to turn OFF the Multiple system power supply before the rotary switch
setting change.
2 - 23
(5) Basic specifications of Q173DCPU/Q172DCPU

(a) Module specifications
Item Q173DCPU Q172DCPU
Internal current consumption (5VDC) [A] 1.25 1.14

Mass [kg] 0.33 0.33
Exterior dimensions [mm(inch)] 98 (3.85)(H) 27.4 (1.08)(W) 119.3 (4.69)(D)
(6) SV13/SV22 Motion control specifications/performance

specifications
(a) Motion control specifications
Number of control axes Up to 32 axes Up to 8 axes

0.44ms/ 1 to 6 axes
0.44ms/ 1 to 6 axes
SV13 0.88ms/ 7 to 18 axes
0.88ms/ 7 to 8 axes
Operation cycle
0.44ms/ 1 to 4 axes
(default)
0.88ms/ 5 to 12 axes 0.44ms/ 1 to 4 axes
SV22
1.77ms/13 to 28 axes 0.88ms/ 5 to 8 axes
Linear interpolation (Up to 4 axes), Circular interpolation (2 axes),
Interpolation functions
Helical interpolation (3 axes)
PTP(Point to Point) control, Speed control, Speed-position control, Fixed-pitch feed,
Control modes Constant speed control, Position follow-up control, Speed control with fixed position stop,
Speed switching control, High-speed oscillation control, Synchronous control (SV22)
Acceleration/ Automatic trapezoidal acceleration/deceleration,
deceleration control S-curve acceleration/deceleration
Compensation Backlash compensation, Electronic gear, Phase compensation (SV22)
Programming language Motion SFC, Dedicated instruction, Mechanical support language (SV22)
Servo program capacity 14k steps
Number of positioning 3200 points
points (Positioning data can be designated indirectly)
Peripheral I/F Via PLC CPU (USB/RS-232)
Proximity dog type (2 types), Count type (3 types), Data set type (2 types), Dog cradle type,
Home position return
Stopper type (2 types), Limit switch combined type
function
(Home position return re-try function provided, home position shift function provided)
JOG operation function Provided
Manual pulse generator
Possible to connect 3 modules
operation function
Synchronous encoder
Possible to connect 12 modules Possible to connect 8 modules
operation function
M-code output function provided
M-code function
M-code completion wait function provided
Limit switch output Number of output points 32 points
function Watch data: Motion control data/Word device
2 - 24
Motion control specifications (continued)

Made compatible by setting battery to servo amplifier.
Absolute position system
(Possible to select the absolute data method or incremental method for each axis)
Number of SSCNET
(Note-1) 2 systems 1 system
systems
Q172DLX : 4 modules usable Q172DLX : 1 module usable
Motion related interface
Q172DEX : 6 modules usable Q172DEX : 4 modules usable
module (Note-2) (Note-2)
Q173DPX : 4 modules usable Q173DPX : 3 modules usable
(Note-1) : The servo amplifiers for SSCNET cannot be used.
(Note-2) : When using the incremental synchronous encoder (SV22 use), you can use above number of modules.
When connecting the manual pulse generator, you can use only 1 module.
2 - 25
(b) Motion SFC performance specifications

Item Q173DCPU/Q172DCPU
Code total
(Motion SFC chart + Operation control 543k bytes
Motion SFC program capacity + Transition)
Text total
484k bytes
(Operation control + Transition)
Number of Motion SFC programs 256 (No.0 to 255)
Motion SFC chart size/program Up to 64k bytes (Included Motion SFC chart comments)
Number of Motion SFC steps/program Up to 4094 steps
Motion SFC program
Number of selective branches/branch 255
Number of parallel branches/branch 255
Parallel branch nesting Up to 4 levels
4096 with F(Once execution type) and FS(Scan execution type)
Number of operation control programs
combined. (F/FS0 to F/FS4095)
Number of transition programs 4096(G0 to G4095)
Operation control program Code size/program Up to approx. 64k bytes (32766 steps)
(F/FS) Number of blocks(line)/program Up to 8192 blocks (in the case of 4 steps(min)/blocks)
/ Number of characters/block Up to 128 (comment included)
Transition program Number of operand/block Up to 64 (operand: constants, word device, bit devices)
(G) ( ) nesting/block Up to 32 levels
Operation control program Calculation expression/bit conditional expression
Descriptive
Calculation expression/bit conditional expression/
expression Transition program
comparison conditional expression
Number of multi execute programs Up to 256
Number of multi active steps Up to 256 steps/all programs
Normal task Execute in main cycle of Motion CPU
Execute in fixed cycle
Event task Fixed cycle
(0.88ms, 1.77ms, 3.55ms, 7.11ms, 14.2ms)
Execute specification (Execution
Executed External Execute when input ON is set among interrupt module QI60
can be
task interrupt (16 points).
masked.)
PLC interrupt Execute with interrupt instruction (D(P).GINT) from PLC CPU.
Execute when input ON is set among interrupt module QI60
NMI task
(16 points).
(7) Selection of Q172DEX, Q173DPX

Synchronous encoder
Item Manual pulse generator
Serial absolute Incremental
Q173DCPU 12 modules
3 modules
Q172DCPU 8 modules
Module selection Q172DEX Q173DPX
2 - 26
2.4.2 Power supply module
(1) Table of the power supply module specifications

This section describes the power supply modules specifications.
Item Q61P-A1 Q61P-A2 Q61P Q62P
Base loading position Q series power supply module loading slot
Applicable base unit Q38DB, Q312DB, Q63B, Q65B, Q68B, Q612B
100 to 120VAC 200 to 240VAC
100 to 240VAC (+10%/-15%)
Input power supply (+10%/-15%) (+10%/-15%)
(85 to 264VAC)
(85 to 132VAC) (170 to 264VAC)
Input frequency 50/60Hz ±5%
Input voltage distortion factor 5% or less
Max. input apparent power 105VA 130VA 105VA
Inrush current 20A 8ms or less (Note-4)
5VDC 6A 3A
Rated output current
24VDC —— 0.6A
External output voltage —— 24VDC±10%
Overcurrent 5VDC 6.6A or more 3.3A or more
protection (Note-1) 24VDC —— 0.66A or more
Overvoltage
5VDC 5.5 to 6.5V
protection (Note-2)
Efficiency 70% or more 65% or more
Allowable momentary power failure
20ms or less
time (Note-3)
Across inputs/LG and outputs/FG
Dielectric withstand voltage
2,830VAC rms / 3 cycles (Altitude : 2000m (6561.68ft.) )
Across inputs and outputs (LG and FG separated), across inputs and LG/FG, across outputs and
Insulation resistance
LG/FG 10M or more by insulation resistance tester (500VDC)
• By noise simulator of 1,500Vp-p noise voltage, 1µs noise width and 25 to 60Hz noise frequency
Noise immunity
• Noise voltage IEC61000-4-4, 2kV
Operation indication LED indication (Normal : ON (Green), Error : OFF)
Fuse Built-in (Unchangeable by user)
Application ERR contact
Rated switching
24VDC, 0.5A
voltage/current
Contact Minimum switching load 5VDC, 1mA
output Response time OFF to ON: 10ms or less. ON to OFF: 12ms or less.
section Mechanical : 20 million times or more
Life time
Electrical : 100 thousand times at rated switching voltage/current or more
Surge suppressor None
Fuse None
Terminal screw size M3.5 screw
Applicable wire size 0.75 to 2mm2
Applicable crimping terminal RAV1.25 to 3.5, RAV2 to 3.5
Applicable tightening torque 0.66 to 0.89 N•m
98(H) × 55.2(W) × 90(D)
Exterior dimensions[mm(inch)]
(3.86(H) × 2.17(W) × 3.54(D) )
Mass [kg] 0.31 0.40 0.39
2 - 27
The power supply module specifications (continued)

Item Q63P Q64P
Base loading position Q series power supply module loading slot
Applicable base unit Q38DB, Q312DB, Q63B, Q65B, Q68B, Q612B
24VDC (+30%/-35%) 100 to 120VAC/200 to 240VAC (+10%/-15%)
Input power supply
(15.6 to 31.2VDC) (85 to 132VAC/170 to 264VAC)
Input frequency —— 50/60Hz ±5%
Input voltage distortion factor —— 5% or less
Max. input apparent power 45W 160VA
Inrush current 100A 1ms or less (at 24VDC input) 20A 8ms or less (Note-4)
5VDC 6A 8.5A
Rated output current
24VDC —— ——
Overcurrent 5VDC 6.6A or more 9.9A or more
protection (Note-1) 24VDC ——
Overvoltage 5VDC 5.5 to 6.5V
protection (Note-2) 24VDC ——
Efficiency 70% or more
Permissible instantaneous power off
10ms or less (at 24VDC input) 20ms or less
time (Note-3)
Across inputs/LG and outputs/FG
Dielectric withstand voltage 500VAC across primary and 5VDC 2,830VAC rms/3 cycles
(Altitude : 2000m (6561.68ft.) )
Across inputs and outputs (LG and FG
separated), across inputs and LG/FG, across
Insulation resistance 10M or more by insulation resistance tester
outputs and LG/FG 10M or more by insulation
resistance tester (500VDC)
• By noise simulator of 1,500Vp-p noise
• By noise simulator of 500Vp-p noise voltage,
voltage, 1µs noise width and 25 to 60Hz noise
Noise immunity 1µs noise width and 25 to 60Hz noise
frequency
frequency
• Noise voltage IEC61000-4-4, 2kV
Operation indication LED indication (Normal : ON (Green), Error : OFF)
Fuse Built-in (Unchangeable by user)
Application ERR contact
Rated switching
24VDC, 0.5A
voltage/current
Contact Minimum switching load 5VDC, 1mA
output Response time OFF to ON: 10ms or less. ON to OFF: 12ms or less
section Mechanical : 20 million times or more
Life time
Electrical : 100 thousand times at rated switching voltage/current or more
Surge suppressor None
Fuse None
Terminal screw size M3.5 screw
Applicable wire size 0.75 to 2mm2
Applicable crimping terminal RAV1.25 to 3.5, RAV2 to 3.5
Applicable tightening torque 0.66 to 0.89 N•m
98(H) × 55.2(W) × 90(D) 98(H) × 55.2(W) × 115(D)
Exterior dimensions[mm(inch)]
(3.86(H) × 2.17(W) × 3.54(D) ) (3.86(H) × 2.17(W) × 4.53(D) )
Mass [kg] 0.33 0.40
2 - 28
POINTS
(Note-1) : Overcurrent protection
The overcurrent protection device shuts off the 5V, 24VDC circuit and
stops the system if the current flowing in the circuit exceeds the specified
value.
The LED of the power supply module is turned off or lights up in dim
green when voltage is lowered. If this device is activated, switch the
input power supply off and eliminate the cause such as insufficient
current capacity or short. Then, a few minutes later, switch it on to restart
the system.
The initial start for the system takes place when the current value
becomes normal.
(Note-2) : Overvoltage protection

The overvoltage protection device shuts off the 5VDC circuit and stops
the system if a voltage of 5.5VDC or more is applied to the circuit.
When this device is activated, the power supply module LED is switched
OFF.
If this happens, switch the input power OFF, then a few minutes later
ON. This causes the initial start for the system to take place. The power
supply module must be changed if the system is not booted and the LED
remains OFF.
2 - 29
POINTS
(Note-3) : Allowable momentary power failure period
(1) For AC input power supply
(a) An instantaneous power failure lasting less than 20ms will cause
AC down to be detected, but operation will continue.
(b) An instantaneous power failure lasting in excess of 20ms may
cause the operation to continue or initial start to take place
depending on the power supply load.
Further, when the AC supply of the AC input module is the same
as that of the power supply module, it prevents the sensor
connected to the AC input module, which is ON at power-off,
from turning OFF by switching off the power supply.
However, if only the AC input module is connected to the AC line,
which is connected to the power supply, detection of the AC
down for the power supply module may be delayed by the
capacitor in the AC input module. Thus, connect a load of
approx. 30mA per AC input module to the AC line.
(2) For DC input power supply
(Note)
(a) An instantaneous power failure lasting less than 10ms will
cause 24VDC down to be detected, but operation will continue.
(Note)
(b) An instantaneous power failure lasting in excess of 10ms
may cause the operation to continue or initial start to take place
depending on the power supply load.
(Note) : This is for a 24VDC input. This is 10ms or less for less
then 24VDC.
(Note-4) : Inrush current

When power is switched on again immediately (within 5 seconds) after
power-off, an inrush current of more than the specified value (2ms or
less) may flow. Reapply power 5 seconds after power-off.
When selecting a fuse and breaker in the external circuit, take account
of the blow out, detection characteristics and above matters.
2 - 30
(2) Names of Parts and Setting

This section describes the names of the parts of each power module.
• Q61P-A1 (100 to 120VAC input, 5VDC 6A output)

• Q61P-A2 (200 to 240VAC input, 5VDC 6A output)
• Q61P (100 to 240VAC input, 5VDC 6A output)
• Q62P (100 to 240VAC input, 5VDC 3A/24VDC 0.6A output)
• Q63P (24VDC input, 5VDC 6A output)
• Q64P (100 to 120VAC/200 to 240VAC input, 5VDC 8.5A output)
9) 1)
Q62P POWER 8)
INPUT
100-240VAC
50/60Hz 105VA
OUTPUT 5VDC 3A 24VDC 0.6A
6) ERR.
+24V 2)
L
(Q62P only) 24G
+ -
24VDC 0.5A
(FG) 3)
(LG) 4)
INPUT N 5)
100-240VAC
L
Q62P
10) 7)
2 - 31

ON (green): Normal (5VDC output, momentary power failure within 20ms)
OFF : • AC power supply is ON, however, the power supply module is out of order.
AC input (5VDC error, internal circuit failure, blown fuse)
power supply • Over current protection or over voltage protection operated.
• AC power supply is not ON
POWER • Power failure (including an momentary power failure of more than 20ms)
1)
LED ON (green): Normal (5VDC output, momentary power failure within 10ms)
OFF : • DC power supply is ON, however, the power supply module is out of order.
DC input (5VDC error, internal circuit failure, blown fuse)
power supply • Over current protection or over voltage protection operated.
• DC power supply is not ON
• Power failure (including an momentary power failure of more than 10ms)
• Turned ON when the whole system operates normally.
• This terminal turns OFF (opens) when the AC power is not input, a stop error (including a
AC input reset) occurs in the CPU module, or the fuse is blown.
power supply • In a Multiple CPU system configuration, turned OFF when a stop error occurs in any of
the CPU modules.
ERR Normally OFF when loaded in an extension base unit.
2)
terminals • Turned ON when the whole system operates normally.
• This terminal turns OFF (opens) when the DC power is not input, a stop error (including a
DC input reset) occurs in the CPU module, or the fuse is blown.
power supply • In a Multiple CPU system configuration, turned OFF when a stop error occurs in any of
the CPU modules.
Normally OFF when loaded in an extension base unit.
3) FG terminal Ground terminal connected to the shield pattern of the printed circuit board.
Grounding for the power supply filter. The potential of Q61P-A1, Q61P-A2, Q61P, Q62P
4) LG terminal
and Q64P terminal is 1/2 of the input voltage.
• Power input terminals connected to a power supply of 100VAC or 200VAC.
(Q61P-A1, Q61P-A2, Q64P)
• Power input terminals connected to a power supply of 100VAC to 200VAC.
5) Power input terminals
(Q61P, Q62P)
• Power input terminals connected to a power supply of 24VDC.
(Q63P)
+24V, 24G terminals
6) Used to supply 24VDC power to inside the output module. (using external wiring)
(Q62P only)
7) Terminal screw M3.5 7 screw
8) Terminal cover Protective cover of the terminal block
Used to fix the module to the base unit.
9) Module fixing screw hole
M3 12 screw (user-prepared) (Tightening torque : 0.36 to 0.48 N•m)
10) Module loading lever Used to load the module into the base unit.
2 - 32
POINTS
(1) The Q61P-A1 is dedicated for inputting a voltage of 100VAC.
Do not input a voltage of 200VAC into it or trouble may occur on the Q61P-A1.
Power Supply power voltage
module type 100VAC 200VAC
Power supply module causes
Q61P-A1 Operates normally.
trouble.
Power supply module does
not cause trouble.
Q61P-A2 Operates normally.
CPU module cannot be
operated.
(2) The Q63P is dedicated for inputting a voltage of 24VDC.

Do not input a voltage of except 24VDC into it or trouble may occur on the Q63P.
(3) Q64P automatically switches the input range 100/200VAC.

Therefore, it is not compatible with the intermediate voltage (133 to 169VAC).
The CPU module may not work normally if the above intermediate voltage is
applied.
(4) Ensure that the earth terminals LG and FG are grounded.

(Ground resistance : 100 or loss)
Since the LG terminal has a half of the input voltage, touching this terminal may
result in an electric shock.
(5) When the Q61P-A1, Q61P-A2, Q61P, Q62P, Q63P or Q64P is loaded on the
extension base unit, a system error cannot be detected by the ERR terminal.
(The ERR terminal is always OFF.)
2 - 33
(3) Selection of the power supply module

The power supply module is selected according to the total of current
consumption of the I/O modules, intelligent function module, and peripheral
devices supplied by its power module. (Select the power supply module in
consideration of the current consumption of the peripheral device connected to
the Q170ENC, MR-HDP01 etc.)
5VDC internal current consumption of shared equipments with PLC might be
changed. Be sure to refer to the PLC Manuals. .
(a) Calculation example of power supply selection

<System configuration (Q173DCPU use)>
Q61P Q03UD Q173D QX40 QX40 Q172DLX Q172DEX Q173DPX QY10 QY10 Q38DB
CPU CPU
MR-HDP01
MR-HDP01
Q170ENC
• 5VDC current consumption of each module

Q03UDCPU : 0.33 [A] Q170ENC : 0.20 [A]
Q173DCPU : 1.25 [A] Q173DPX : 0.38 [A]
QX40 : 0.05 [A] MR-HDP01 : 0.06 [A]
Q172DLX : 0.06 [A] QY10 : 0.43 [A]
Q172DEX : 0.19 [A] Q38DB : 0.228 [A]
• Power consumption of overall modules

I5V = 0.33 + 1.25 + 0.05 2 + 0.06 + 0.19 + 0.20 + 0.38 + 0.06 2 +
0.43 2 + 0.228 = 3.718[A]
Select of the power supply module (Q61P (100/240VAC) 6A) according to
this internal current consumption 3.718[A].
(Note) : Configure the system in such a way that the total current
consumption at 5VDC of all the modules is less than the
allowable value.
2 - 34
2.4.3. Base unit and extension cable
This section describes the specifications of the extension cables for the base units
(Main base unit or extension base unit) used in the system, and the specification
standards of the extension base unit.
5VDC internal current consumption of base unit might be changed. Be sure to refer to
the PLC Manuals.
(1) Table of the base unit specifications

(a) Main base unit specifications
Type
Q38DB Q312DB
Item
Number of I/O modules 8 12
Possibility of extension Extendable
Applicable module Q series modules
5VDC internal current
0.228 0.233
consumption [A]
Fixing hole size M4 screw hole or 4.5 hole (for M4 screw)
Exterior dimensions 328(W) 98(H) 44.1(D) 439(W) 98(H) 44.1(D)
[mm(inch)] (12.91(W) 3.86(H) 1.74(D) ) (17.28(W) 3.86(H) 1.74(D) )
Mass [kg] 0.41 0.54
Attachment Fixing screw M4 14 5 pieces (DIN rail fixing adapter is optional)
(Note): It is impossible to mount the main base unit by DIN rail when using the Motion CPU module.
Doing so could result in vibration that may cause erroneous operation.
(b) Extension base unit specifications

Type
Q63B Q65B Q68B Q612B
Item
Number of I/O modules 3 5 8 12
Possibility of extension Extendable
Applicable module Q series modules
5VDC internal current
0.105 0.110 0.114 0.121
consumption [A]
Fixing hole size M4 screw hole or 4.5 hole (for M4 screw)
189(W) 98(H) 245(W) 98(H) 328(W) 98(H) 439(W) 98(H)
Exterior dimensions 44.1(D) 44.1(D) 44.1(D) 44.1(D)
[mm(inch)] (7.44(W) 3.86(H) (9.65(W) 3.86(H) (12.91(W) 3.86(H) (17.28(W) 3.86(H)
1.74(D) ) 1.74(D) ) 1.74(D) ) 1.74(D) )
Mass [kg] 0.23 0.28 0.38 0.48
(Note)
Attachment Fixing screw M4 14 4 pieces
(Note): The 5 base mounting screws are included with the Q38B and Q312B that have 5 base mounting holes.
2 - 35
(2) Table of the extension cable specifications

The list below describes the specifications of the extension cables which can
be used for the PLC CPU system.
Type
QC05B QC06B QC12B QC30B QC50B QC100B
Item
Cable length[m(ft.)] 0.45(1.48) 0.6(1.97) 1.2(3.94) 3.0(9.84) 5.0(16.40) 10.0(32.81)
Connection between the main base unit and extension base unit,
Application
or connection between the extension base units.
Mass [kg] 0.15 0.16 0.22 0.40 0.60 1.11
POINT
When the extension cables are used in combination, limit the overall length of the
combined cable to 13.2m (43.31ft.).
(3) Names of parts of the base unit

Names of parts of the base unit are described below.
(a) Main base unit (Q38DB, Q312DB)
5) 4)
OUT
1) 5V
2) SG
POWER CPU I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11
FG Q312DB
3)

Extension cable Connector for connecting an extension cable (for signal communications with the
1)
connector extension base unit)
Protective cover of extension cable connector. Before an extension cable is connected,
2) Base cover the area of the base cover surrounded by the groove under the word "OUT" on the base
cover must be removed with a tool such as nippers.
Connector for installing the Q series power supply module, CPU module, I/O modules, and
intelligent function module.
3) Module connector To the connectors located in the spare space where these modules are not installed,
attach the supplied connector cover or the blank cover module (QG60) to prevent entry of
dirt.
4) Module fixing screw hole Screw hole for fixing the module to the base unit. Screw size: M3 12
5) Base mounting hole Hole for mounting this base unit onto the panel of the control panel (for M4 screw)
(Note): It is impossible to mount the main base unit by DIN rail when using the Motion CPU module. Doing so could result in
vibration that may cause erroneous operation.
2 - 36
(4) I/O allocations

It is possible to allocate unique I/O No.s for each Motion CPU independently of
the PLC’s I/O No.s. (I/O No.s are unique between the Q series PLC CPU within a
given system, but the I/O No.s of the Motion CPU are unique for each Motion
CPU.)
ON/OFF data input to the Motion CPU is handled via input devices PX , while
ON/OFF data output from the Motion CPU is handled via output devices PY .
It is not mandatory to match the I/O device PX/PY No.s used in the Motion
program with the PLC I/O No.s; but it is recommended to make them match as
much as possible.
The following figure shows an example of I/O allocation.
I/O Allocations
0 1 2 3 4 5 6 7 8 9
Power supply
QnUD(H) QnUD(H) Q173D QX41 QY41 QY41 Q172DLX QX41 QY41 QY41
CPU CPU CPU
module
X0 to X1F Y20 to Y3F Y40 to Y5F Intelligent PX0 to PX1F PY20 to PY3F YC0 to YDF
32 points
(X60 to X7F) (Y80 to Y9F) (YA0 to YBF)
CPU No.1 CPU No.2 CPU No.3 Module of Module of Module of Module of Module of Module of Module of
control control control control control control control
CPU No.1 CPU No.1 CPU No.2 CPU No.3 CPU No.3 CPU No.3 CPU No.1
(Note-1) : When the number of modules to be installed is 32 points.

(Note-2) : When the PX/PY No. does not match the PLC I/O No.
Refer to the Q173DCPU/Q172DCPU Motion Controller Programming Manual

(COMMON) about the I/O allocation setting method.
Refer to the QCPU User's Manual (Function Explanation, Program Fundamentals)
about the I/O allocation setting method of the QnUD(H)CPU.
POINT
I/O device of the Motion CPU can be set in the range PX/PY000 to PX/PYFFF.
The real I/O points must be 256 points or less. (As for the I/O No., it is possible not
to continue.)
2 - 37
2.4.4 Q172DLX Servo external signals interface module
Q172DLX receives external signals (servo external signals) required for positioning
control.
(1) Q172DLX name of parts
1)
5) Q172DLX
2)
3)
CTRL
6) Q172DLX
4)

Hook used to fix the module to the base unit.
1) Module fixing hook
(Single-motion installation)
Display the servo external input status from the external
equipment.
LED Details
Display for servo external signal input status of
2) Mode judging LED 0 to 1F
each axis.
The proximity dog/speed-position switching signal (DOG/
CHANGE) does not turn ON without setting Q172DLX in the
system setting.
3) CTRL connector The servo external signal input connector of each axis.
4) Module loading lever Used to install the module to the base unit.
Module fixing screw Hole for the screw used to fix to the base unit.
5)
hole (M3×12 screw : Purchase from the other supplier)
6) Module fixing hook Hook used to fix to the base unit.
POINT
Mode judging LED of the proximity dog/speed-position switching signal (DOG/
CHANGE) turns ON at the following conditions.
• Q172DLX is set on the system setting display of MT Developer.
• The proximity dog/speed-position switching signal (DOG/CHANGE) is input.
2 - 38
(2) Performance specifications

Item Specifications
Number of I/O occupying points 32 points(I/O allocation: Intelligent, 32 points)
Internal current consumption(5VDC) [A] 0.06
98(H) 27.4(W) 90(D)
Exterior dimensions [mm(inch)]
(3.86(H) 1.08(W) 3.54(D) )
Mass [kg] 0.15
(b) Input
Item Specifications
Servo external signals : 32 points
(Upper stroke limit, Lower stroke limit, Stop input,
Number of input points
Proximity dog/Speed-position switching signal)
(4 points 8 axes)
Input method Sink/Source type
Isolation method Photocoupler
Rated input voltage 12/24VDC
Rated input current 12VDC 2mA/24VDC 4mA
10.2 to 26.4VDC
Operating voltage range
(12/24VDC +10/ -15%, ripple ratio 5% or less)
ON voltage/current 10VDC or more/2.0mA or more
OFF voltage/current 1.8VDC or less/0.18mA or less
Input resistance Approx. 5.6k
Response time of the OFF to ON
Upper/Lower stroke limit and 1ms
STOP signal ON to OFF
Response time of the OFF to ON 0.4ms/0.6ms/1ms

proximity dog, Speed-
ON to OFF (CPU parameter setting, Default 0.4ms)
position switching signal
Common terminal arrangement 32 points/common (common terminal: B1, B2)
Indicates to display ON indication (LED)
External connector type 40 pin connector
2
Applicable wire size 0.3mm
Applicable connector for the external A6CON1(Attachment),
connection A6CON2, A6CON3(Optional)
Applicable connector/
A6TBXY36, A6TBXY54, A6TBXY70(Optional)
Terminal block converter module
2 - 39
(3) Connection of servo external signals interface module

(a) Servo external signals
There are the following servo external signals.
(Upper stroke limit is limit value of address increase direction/lower stroke
limit is limit value of an address decrease direction.)
The Q172DLX is assigned a set of input No.s per axis. Make the system
setting of MT Developer to determine the I/O No.s corresponding to the
axis No.s.
Number of points
Servo external signal Application
on one Q172DLX
Upper stroke limit input (FLS)
For detection of upper and lower stroke limits.
Lower stroke limit input (RLS)
Stop signal input (STOP) For stopping under speed or positioning control. 32 points
Proximity dog/ For detection of proximity dog at proximity dog or count (4 points/8 axes)
Speed-position switching input type home position return of for switching from speed to
(DOG/CHANGE) position switching control.
2 - 40
(b) The pin layout of the CTRL connector

Use the CTRL connector at the Q172DLX module front to connect the
servo external signals.
The following pin layout of the Q172DLX CTRL connector viewed from the
front.
The pin layout and connection description of the CTRL connector are
described below.
CTRL connector
Pin No. Signal Name Pin No. Signal Name Signal No.
Signal No.
B20 FLS1 A20 FLS5
B19 RLS1 A19 RLS5
1 5
B18 STOP1 A18 STOP5
B17 DOG1/CHANGE1 A17 DOG5/CHANGE5
B16 FLS2 A16 FLS6
B15 RLS2 A15 RLS6
2 6
B14 STOP2 A14 STOP6
B12 FLS3 A12 FLS7

B11 RLS3 A11 RLS7
3 7
B10 STOP3 A10 STOP7
B8 FLS4 A8 FLS8
B7 RLS4 A7 RLS8
4 8
B6 STOP4 A6 STOP8
B4 No connect A4 No connect
B2 COM A2 No connect
B1 COM A1 No connect
Applicable connector model name

A6CON1 type soldering type connector
FCN-361J040-AU connector (FUJITSU TAKAMISAWA (Attachment)
COMPONENT LIMITED)
FCN-360C040-B connector cover
A6CON2 type Crimp-contact type connector
(Optional)
A6CON3 type Pressure-displacement type connector
DOG/CHANGE, STOP, RLS, FLS functions of each axis(1 to 8) For information about
signal details, refer to
DOG/CHANGE Proximity dog/Speed-position
the programming manual.
switching signal
STOP Stop signal
RLS Lower stroke limit
FLS Upper stroke limit
(Note) : Connector/terminal block conversion modules and cables can be

used at the wiring of CTRL connector.
A6TBXY36/A6TBXY54/A6TBX70 : Connector/terminal block
conversion module
AC TB ( :Length [m]) : Connector/terminal block
conversion cable
POINT
Signal No. 1 to 8 can be assigned to the specified axis. Make the assignment in the
system settings of MT Developer.
2 - 41
(4) Interface between CTRL connector and servo external signal

Input or CTRL
Signal name LED Wiring example Internal circuit Specification Description
Output connector
FLS1 B20 0 Supply voltage
FLS2 B16 4 12 to 24 VDC
FLS3 B12 8 Upper stroke (10.2 to 26.4 VDC,
FLS4 B8 C stabilized power
limit input 5.6k FLS
supply)
FLS5 A20 10
FLS6 A16 14
FLS7 A12 18
FLS8 A8 1C
RLS1 B19 1
RLS2 B15 5
RLS3 B11 9
RLS4 B7 D
Lower stroke RLS
RLS5 A19 11
limit input 5.6k
RLS6 A15 15
RLS7 A11 19
Input High level
RLS8 A7 1D
10.0 VDC or more/
STOP1 B18 2 2.0mA or more
STOP2 B14 6
STOP3 B10 A
STOP4 B6 E
Stop signal STOP
STOP5 A18 12
input 5.6k
STOP6 A14 16
STOP7 A10 1A
STOP8 A6 1E Low level
B17 3 1.8 VDC or less/
DOG/CHANGE1
0.18mA or less
DOG/CHANGE2 B13 7
Proximity dog/
DOG/CHANGE3 B9 B
Speed-position
DOG/CHANGE4 B5 F
switching signal DOG/CHANGE
DOG/CHANGE5 A17 13
DOG/CHANGE6 A13 17 5.6k
DOG/CHANGE7 A9 1B
DOG/CHANGE8 A5 1F
Common terminals
Power supply for motion control
B1 B2 signals, external
(Note)
12VDC to 24VDC signal.
(Note): As for the connection to power line (B1, B2), both "+" and "–" are possible.
CAUTION
Always use a shield cable for connection of the CTRL connector and external equipment, and
avoid running it close to or bundling it with the power and main circuit cables to minimize the
influence of electromagnetic interface. (Separate them more than 200mm (0.66ft.) away.)
Connect the shield wire of the connection cable to the FG terminal of the external equipment.
Make parameter setting correctly. Incorrect setting may disable the protective functions such
as stroke limit protection.
Always wire the cables when power is off. Not doing so may damage the circuit of modules.
Wire the cable correctly. Wrong wiring may damage the internal circuit.
2 - 42
2.4.5 Q172DEX Synchronous encoder interface module
Q172DEX receive external signals required for serial absolute synchronous encoder.
The installation position of Q172DEX is only main base.
(1) Q172DEX name of parts
1)
5) Q172DEX
SY.ENC TREN
1 1 2)
2 2
SY.ENC1 3)
8)
LITHIUM BATTERY
MITSUBISHI
SY.ENC2
6) Q172DEX
9) 7) 4)

Display the input status from the external equipment.
LED Details
Display for signal input status of each serial
SY.ENC absolute synchronous encoder.
1, 2 (LED turns ON at the normal connection (first
2) Mode judging LED
switching to virtual mode).)
TREN
Display for signal status of tracking enable.
1, 2
The tracking enable signal does not turn ON without
setting Q172DEX in the system setting.
3) SY. ENC connector Input connector of the serial absolute synchronous encoder.
Module fixing screw Hole for the screw used to fix to the base unit
5)
7) Battery connector For connection of battery lead wire.
8) Battery holder Used to the set the Battery (A6BAT/MR-BAT) to the holder.
Battery
9) For Serial absolute synchronous encoder battery backup.
(A6BAT/MR-BAT)
2 - 43
POINT
(1) Mode judging LED of the serial absolute synchronous encoder signal turns ON
at the normal connection (first switching to virtual mode).
(2) Mode judging LED of the tracking enable signal turns ON at the following
conditions.
• Q172DEX is set on the system structure screen of MT Developer.
• The tracking enable signal is input.

Item Specifications
Internal current consumption(5VDC)[A] 0.19
98(H) 27.4(W) 90(D)
(3.86(H) 1.08(W) 3.54(D) )
Mass [kg] 0.15
(b) Tracking enable signal input

Item Specifications
Number of input points Tracking enable signal : 2 points
10.2 to 26.4VDC
OFF to ON 0.4ms/0.6ms/1ms
Response time
Common terminal arrangement 1 point/common (Common terminal: TREN.COM)
Indicates to display ON indication (LED)
2 - 44
(c) Serial absolute synchronous encoder input

Item Specifications
Applicable signal types Differential-output type : (SN75C1168 or equivalent)
Transmission method Serial communications
Synchronous method Counter-clock-wise (viewed from end of shaft)
Communication speed 2.5Mbps
Applicable types Q170ENC
Position detection method Absolute (ABS) method
Resolution 262144PLS/rev (18bit)
Number of modules 2/module
Applicable connector for
Q170ENCCNS (Optional)
the external connection
Applicable wire MB14B0023 12Pair
Q170ENCCBL M
Connecting cable ( =cable length 2m(6.56ft.), 5m(16.40ft.), 10m(32.81ft.), 20m(65.62ft.),
(Note-1)
30m(98.43ft.), 50m(164.04ft.) )
Cable length Up to 50m (164.04ft.)
Back up the absolute position. Depends on A6BAT/MR-BAT.
Battery service life time 12000[h], (Example of encoders 2, Ambient temperature 40°C (104°F) )
(value in actual) 24000[h], (Example of encoders 1, Ambient temperature 40°C (104°F) )
(Note-1) : You can use these cables when the tracking enable signal is not used.
When the tracking enable signal is used, fabricate the cable on the customer side.
2 - 45
(3) Select to number of the synchronous encoder modules

Synchronous encoders are available in voltage output type(incremental),
differential output type(incremental) and serial absolute output type(Q170ENC).
Q172DEX can be connected to only serial absolute output type(Q170ENC).
When using the incremental synchronous encoder of voltage output type or
differential output type, must be used Q173DPX. (The synchronous encoders are
used only in the SV22 virtual mode.)
In addition, the usable numbers of synchronous encoders differ depending on the
modules.
The following number of serial absolute synchronous encoders and incremental
synchronous encoders combined can be used.
Motion CPU module Synchronous encoder

Q173DCPU Up to 12 modules ( Q172DEX: Up to 6 modules )
Q172DCPU Up to 8 modules ( Q172DEX: Up to 4 modules )
• Tracking enable signal

Tracking enable signal of Q172DEX is used as a high-speed reading
function. It cannot be used, as the input start signal which start the input
form serial absolute synchronous encoders.
When using the inputs start signal which start the input from synchronous
encoder, must be used Q173DPX. (Type of synchronous encoder is
voltage output(incremental)or differential output(incremental). )
The external input signal of the synchronous encoder is indicated below.
External input signal of the Number of points on

Item
synchronous encoder one Q172DEX
Tracking enable signal input High-speed reading function 2 points
2 - 46
(4) Connection of synchronous encoder interface module.

(a) Connection with serial absolute synchronous encoder
(Q170ENC)
Use the SY.ENC connector at the Q172DEX module front to connect the
serial absolute synchronous encoder (Q170ENC).
When tracking enable signal is not used, use the Q170ENCCBL M
encoder cable between the serial absolute synchronous encoder
(Q170ENC) and SY.ENC connector.
The following pin layout of the Q172DEX SY.ENC connector viewed from
the front.
The pin layout and connection description of the SY.ENC connector are
described below.
SY.ENC connector
Signal Signal Applicable connector
Pin No. Pin No. model names
name name
10120-3000PE connector
1 LG 11 LG 10320-52F0-008 connector cover
2 LG 12 LG (3M make)
3 LG 13 No connect
4 TREN 14 TREN.CO
5 No connect 15 No connect
6 MD 16 MDR
7 MR 17 MRR
8 No connect 18 P5
9 BAT 19 P5
10 P5 20 P5
(Note) : Do not connect a wire to MD(6Pin), MDR(16Pin).
(b) Interface with external equipment

The interface between the SY.ENC connector and external equipment is
described below.
1) Wiring precautions
Ensure the connector lock after connecting the connector.
Synchronous encoder interface module
(Q172DEX)
SW
1 2
STOP RUN
CAUTION
EMI
CN1
CN2
FRO NT
BA T
SY.ENC connector

(Q170ENCCBL M)
Serial absolute synchronous encoder

(Q170ENC)
2 - 47
(5) Interface between SY.ENC connector and external equipment

Input or Signal Pin No.
Wiring example Internal circuit Specification Description
Output name SY.ENC connector
Transmission method:
MR 7 Serial serial communications
absolute
Position detection
synchronous method: absolute
encoder
MRR 17
P5 10 18 19 20
5VDC
LG 1 2 3 11 12
Input Battery
BAT 9
TREN 4 5.6k
(Note)
TREN.
COM 14
(Note)
12VDC to 24VDC
SD plate
(Note) : As for the connection to power line (TREN, TREN.COM), both "+" and "–" are possible.
CAUTION
Always use a shield cable for connection of the SY.ENC connector and external equipment, and
avoid running it close to or bundling it with the power and main circuit cables to minimize the
influence of electromagnetic interface. (Separate them more than 200mm (0.66 ft.) away.)
Connect the shield wire of the connection cable to the FG terminal of the external equipment.
When increasing the cable length, use the cable 50m(164.04ft.) or less. Note that the cable
should be run in the shortest possible distance to avoid induced noise.
Always wire the cables when power is off. Not doing so may damage the circuit of modules.
Wire the cable correctly. Wrong wiring may damage the internal circuit.
2 - 48
(6) Details of encoder cable connections

(a) When not using tracking enable signal (Note-1)
SY.ENC side connector Synchronous encoder side connector(plug)
10120-3000PE (connector)
10320-52F0-008(connector case) MS3106B22-14S(cable clump)
P5 19 S
LG 11 R
P5 20
LG 12
P5 18
LG 2
BAT 9 E
LG 1
MR 7 K
MRR 17 L
MD 6 H
MDR 16 J
SDplate N
:Twisted pair cable
Q170ENCCBL2M to Q170ENCCBL50M(50m (164.04ft.) or less)

(Note-1), (Note-2)
(b) When using tracking enable signal
SY.ENC side connector Synchronous encoder side connector(plug)
10120-3000PE (connector)
10320-52F0-008(connector case) MS3106B22-14S(cable clump)
P5 19 S
LG 11 R
P5 20
LG 12
P5 18
LG 2
BAT 9 E
LG 1
MR 7 K
MRR 17 L
MD 6 H
MDR 16 J
SDplate
TREN 4 N
TREN.COM 14
24VDC
:Twisted pair cable
Cable length 50m(164.04ft.) or less
(Note-1) : Be sure to use a wire model name AWG24.

(Note-2) : When using tracking enable signal, fabricate the encoder cable by customer side.
2 - 49
(7) Connection of the battery

This section describes the battery specifications, handling precautions and
installation of the Q172DEX.
(a) Specifications
The specifications of the battery for memory back-up are shown in the table
below.
Battery Specifications
Model name
A6BAT/MR-BAT
Item
Classification Manganese dioxide lithium primary battery
Normal voltage [V] 3.6
Nominal current [mAh] 1600
Storage life 5 years
Lithium content [g] 0.48
For backup absolute positioning data of the serial absolute
Applications
synchronous encoder (Q170ENC)
Exterior dimensions [mm(inch)] 16(0.63) × 30(1.18)
(Note) : The 44th Edition of the IATA (International Air Transportation Association) Dangerous Goods Regulations
was effected in January 1st, 2003 and administered immediately.
In this edition, the provisions relating to lithium and lithium ion batteries have been revised to strengthen
regulations on the air transportation of battery.
This battery is not dangerous goods (not class 9). Therefore, these batteries of 24 units or less are not
subject to the regulations.
These batteries more than 24 units require packing based on Packing Instruction 903.
If you need the self-certification form for the battery safety test, contact Mitsubishi.
For more information, contact Mitsubishi.
(b) Battery replacement

For Battery replacement procedure, refer to section 6.5.2.
Battery is supplied to the

serial absolute synchronous
encoder by the encoder
cable. Battery connector
A6BAT/MR-BAT
LITHIUM BATTERY
MITSUBISHI
2 - 50
(c) Battery life

Battery life (Total power failure time) [h] (Note-1)
Actual service value
Guaranteed value Guaranteed value (Note-5)
Module type Battery type Power-on time (Note-3) (Note-4) Backup time
ratio (Note-2) (Reference value) after alarm
(MIN) (75°C (167°F)) (TYP) (40°C (104°F))
(TYP) (25°C (77°F))
0% 3000 8000 24000
30% 4000 11000 34000
Q170ENC×1 50% 6000 16000 43800
70% 10000 26000 43800 40
Internal battery
100% 43800 43800 43800 (After Error
Q172DEX (A6BAT/
0% 1500 4000 12000 code 1152
MR-BAT)
30% 2000 5500 17000 occurrence)
Q170ENC×2 50% 3000 8000 21900
70% 5000 13000 21900
100% 43800 43800 43800
(Note-1) : The actual service value indicates the average value, and the guaranteed time indicates the minimum time.
(Note-2) : The power-on time ratio indicates the ratio of Multiple CPU system power-on time to one day (24 hours).
(When the total power-on time is 17 hours and the total power-off time is 7 hours, the power-on time ratio is 70%.)
(Note-3) : The guaranteed value (MIN) ; equivalent to the total power failure time that is calculated based on the characteristics value of
the memory (SRAM) supplied by the manufacturer and under the storage ambient temperature range of -25°C to 75°C (-13 to
167°F) (operating ambient temperature of 0°C to 55°C (32 to 131°F)).
(Note-4) : The guaranteed value (TYP) ; equivalent to the total power failure time that is calculated based on the normal air-conditioned
environment (40°C (104°F)).
(Note-5) : The actual service value (Reference value) ; equivalent to the total power failure time that is calculated based on the measured
value and under the storage ambient temperature of 25°C (77°F). This value is intended for reference only, as it varies with
characteristics of the memory.
POINTS
The self-discharge influences the life of battery without the connection to Q172DEX.
The external battery should be exchanged approximately every 4 or 5 years.
And, exchange the battery with a new one in 4 to 5 years even if a total power
failure time is guaranteed value or less.
CAUTION
Do not short a battery.
Do not charge a battery.
Do not disassemble a battery.
Do not burn a battery.
Do not overheat a battery.
Do not solder the battery terminals.
Before touching the battery, always touch grounded metal, etc. to discharge static electricity from
Do not directly touch the module's conductive parts and electronic components. Touching them
could cause an operation failure or give damage to the module.
2 - 51
2.4.6 Q173DPX Manual pulse generator interface module
Q173DPX receive external signals required for Manual pulse generator and
Incremental synchronous encoder (Voltage-output/Open collector type/Differential-
output type).
(1) Q173DPX name of parts

1)
5) Q173DPX
PLS.A PLS.B TREN
1 1 1 2)
2 2 2
3 3 3
PULSER
3)
ON
1 2 3 4 5 6
6)
KSD06S
7) Q173DPX
4)

Display the input status from the external equipment.
LED Details
Display for input signal status of
PLS.A 1 to 3
manual pulse generator/incremental
PLS.B 1 to 3
2) Mode judging LED synchronous encoder phases A, B
Display for signal status of tracking
TREN 1 to 3
enable.
The manual pulse generator/incremental synchronous
encoder phases A, B and tracking enable signal does not
turn ON without setting Q173DPX in the system setting.
Input connector of the Manual pulse generator/Incremental
3) PULSER connector
synchronous encoder.
Module fixing screw Hole for the screw used to fix to the base unit
5)
2 - 52

Detection setting of TREN1 signal
Dip switch 1 SW1 SW2
OFF OFF
TREN is detected at leading
ON ON
edge of TREN signal.
ON OFF
Dip switch 2
Dip switches
(Note-1) TREN is detected at trailing
OFF ON
ON
1 2 3 4 5 6
Detection setting of TREN2 signal
Dip switch 3 SW3 SW4
OFF OFF
6) ON ON
ON OFF
Dip switch 4
TREN is detected at trailing
OFF ON
(Shipped from the edge of TREN signal.
factory in OFF Detection setting of TREN3 signal
position) Dip switch 5 SW5 SW6
OFF OFF
ON ON
ON OFF
Dip switch 6
TREN is detected at trailing
OFF ON
(Note-1) : The function is different according to the operating system software installed.
CAUTION
Before touching the battery, always touch grounded metal, etc. to discharge static electricity
from human body. Failure to do so may cause the module to fail or malfunction.
POINTS
Mode judging LED of the manual pulse generator/incremental synchronous encoder
phases A, B and tracking enable signal turns ON at the following conditions.
(1) PLS.A 1 to 3, PLS.B 1 to 3
• Q173DPX is set on the system structure screen of MT Developer.
• All axes servo ON command (M2042) turned on.
• Manual pulse generator enable flag (M2051, M2052, M2053) turned on.
• Manual pulse generator signal is input.
(2) TREN 1 to 3
• Q173DPX is set on the system structure screen of MT Developer.
• The tracking enable signal is input.
2 - 53

Item Specifications
Internal current consumption(5VDC)[A] 0.38
98(H) 27.4(W) 90(D)
(3.86(H) 1.08(W) 3.54(D) )
Mass [kg] 0.15
(b) Tracking enable signal input

Item Specifications
Number of input points Tracking enable signal : 3 points
10.2 to 26.4VDC
OFF to ON 0.4ms/0.6ms/1ms
Response time
Common terminal arrangement 1 point/common(Common contact: TREN.COM)
Indicates to display ON indication(LED)
(Note): Functions are different depending on the operating system software installed.
2 - 54
(c) Manual pulse generator/Incremental synchronous encoder

input
Item Specifications
Number of modules 3/module
Voltage-output/ High-voltage 3.0 to 5.25VDC
Open collector type Low-voltage 0 to 1.0VDC
Differential-output type High-voltage 2.0 to 5.25VDC
(26LS31 or equivalent) Low-voltage 0 to 0.8VDC
Input frequency Up to 200kpps (After magnification by 4)
Voltage-output type/Open-collector type (5VDC), Recommended
Applicable types product: MR-HDP01
Differential-output type: (26LS31 or equivalent)
2
Applicable wire size 0.3mm
Applicable connector for the external A6CON1(Attachment)
connection A6CON2, A6CON3(Optional)
Voltage-output/
30m (98.43ft.)
Cable length Open collector type
(Open collector type: 10m (32.81ft.) )
Differential-output type
(3) Connection of manual pulse generator

Manual pulse generators are available in voltage output/open collector type and
differential output type. Since these types differ in connection method, design
according to the connection method of section 2.4.6 (5).
In addition the usable numbers of manual pulse generator which can be used
with each CPU modules are up to 3 modules.
Motion CPU module Manual pulse generator
Q173DCPU Up to 3 modules
Q172DCPU ( Up to 1 module )
2 - 55
(4) Connection of incremental synchronous encoder

Incremental synchronous encoders are available in voltage output/Open collector
type and differential output type. Since these types differ in connection method,
design according to the connection method of section 2.4.6 (5).
Serial absolute synchronous encoder (Q170ENC) not connected to Q173DPX.
Then connect to Q172DEX.
In addition, the usable numbers of synchronous encoders differ depending on the
modules.
The following number of serial absolute synchronous encoders and incremental
synchronous encoders combined can be used.
Motion CPU module Synchronous encoder

Up to 12 modules
Q173DCPU
( Q173DPX: Up to 4 modules )
Up to 8 modules
Q172DCPU
( Q173DPX: Up to 3 modules )
• Tracking enable signal

Tracking enable signal of Q173DPX is used to start the input from
incremental synchronous encoders.
The external input signal of the incremental synchronous encoder is
indicated below.
This signal is used as the input start signal or high-speed reading function
from incremental synchronous encoder.
External input signal of the Number of points on

Item
incremental synchronous encoder one Q173DPX
Input start function from incremental Each 1 point

Tracking enable signal input
synchronous encoder ( Total 3 points )
2 - 56
(5) Connection of manual pulse generator interface module

(a) The pin layout of the PULSER connector
Use the PULSER connector at the Q173DPX module front to connect the
manual pulse signals, incremental synchronous encoder signals.
The following pin layout of the Q173DPX PULSER connector viewed from
the front.
The pin layout and connection description of the PULSER connector are
described below.
PULSER connector
Pin No. Signal Name Pin No. Signal Name
2) B20 HB1 A20 HA1 2)
B19 SG A19 SG
B18 5V A18 HPSEL1 1)
B17 HA1N A17 HA1P
3) 3)
B16 HB1N A16 HB1P
2) B15 HB2 A15 HA2 2)
B14 SG A14 SG
B13 5V A13 HPSEL2 1)
B12 HA2N A12 HA2P
3) 3)
B11 HB2N A11 HB2P
2) B10 HB3 A10 HA3 2)
B9 SG A9 SG
B8 5V A8 HPSEL3 1)
B7 HA3N A7 HA3P
3) 3)
B6 HB3N A6 HB3P
B4 TREN1 A4 TREN1
B3 TREN2 A3 TREN2
B2 TREN3 A2 TREN3
4) B1 FG A1 FG 4)
Applicable connector model name

A6CON1 type soldering type connector
FCN-361J040-AU connector (FUJITSU TAKAMISAWA (Attachment)
COMPONENT LIMITED)
FCN-360C040-B connector cover
A6CON2 type Crimp-contact type connector
(Optional)
A6CON3 type Pressure-displacement type connector
1) : Input type from manual pulse generator/incremental synchronous

encoder switched by HPSEL .
Not connection : Voltage-output type/open collector type.
HPSEL -SG connection : Differential-output type.
(Switching is possible for each input 1 to 3)
2) : Voltage output/open collector type
Connect the A-phase signal to HA1P/HA2P/HA3P, and the B-phase
signal to HB1P/HB2P/HB3P.
3) : Differential output type
Connect the A-phase signal to HA1P/HA2P/HA3P, and the A-phase
inverse signal to HA1N/HA2N/HA3N.
Connect the B-phase signal to HB1P/HB2P/HB3P, and the B-phase
inverse signal to HB1N/HB2N/HB3N.
4) : Connect the shield cable between manual pulse generator/incremental
synchronous encoder and Q173DPX at the FG signal.
5) : Connector/terminal block conversion modules cannot be used.
2 - 57
(b) Interface between PULSER connector and manual pulse

generator (Differential output type)/Incremental synchronous
encoder
Interface between Manual pulse generator (Differential output type)/
Incremental synchronous encoder
Pin No.
PULSER connector
Input or
Signal name Voltage-Output Wiring example Internal circuit Specification Description
Output type
1 2 3
Rated input voltage For connection
Manual A A17 A12 A7 5.5VDC or less
A manual pulse
pulse HA P
generator
generator, A HIGH level
A Phases A, B
phase A B17 B12 B7 2.0 to 5.25VDC
HA N Pulse width
Manual pulse 20 s or more
generator/
B synchronous
Manual LOW level
A16 A11 A6 encoder 5 s 5 s
Input pulse HB P B 0.8VDC or less or more or more
(Duty ratio: 50% 25%)

generator,
B 26LS31 or Leading edge, Trailing
phase B B B16 B11 B6
equivalent edge time 1 s or less.
HB N
Phase difference
Phase A
Select type
(Note-2) Phase B
signal A18 A13 A8 2.5 s or
more
HPSEL (1) Positioning address
increases if Phase A
leads Phase B.
(Note-1) Power supply (2) Positioning address
P5 B18 B13 B8 5VDC decreases if Phase B
5V leads Phase A.
Power
supply SG
A19 A14 A9
SG
B19 B14 B9
(Note-1) : The 5V(P5)DC power supply from the Q173DPX must not be connected if a separated power
supply is used as the Manual pulse generator/Incremental synchronous encoder power supply.
Use a 5V stabilized power supply as a separated power supply. Any other power supply may
cause a failure.
(Note-2) : Connect HPSEL to the SG terminal if the manual pulse generator (differential output type)
/incremental synchronous encoder is used.
2 - 58
(c) Interface between PULSER connector and manual pulse

generator (Voltage output/Open collector type)/
Incremental synchronous encoder.
Interface between Manual pulse generator (Voltage-output/Open collector
type)/Incremental synchronous encoder
Pin No.
PULSER connector
Input or
Signal name Voltage-Output Wiring example Internal circuit Specification Description
Output
type
1 2 3
Manual Rated input voltage For connection
pulse A 5.5VDC or less manual pulse
generator, A20 A15 A10 generator
HIGH level Phases A, B
phase A 3 to 5.25VDC/
Pulse width
HA Manual pulse 2mA or less 20 s or more
generator/
Manual synchronous LOW level 5 s 5 s
encoder
Input pulse B 1VDC or less/ or more or more
(Duty ratio: 50% 25%)

generator, B20 B15 B10 5mA or more
Leading edge, Trailing
phase B edge time 1 s or less.
Phase difference
HB
Phase A
Select type Phase B
2.5 s or
signal A18 A13 A8 No connect more
(1) Positioning address
HPSEL
increases if Phase A
leads Phase B.
(2) Positioning address
(Note) decreases if Phase B
Power supply
P5 B18 B13 B8 leads Phase A.
5V 5VDC
Power
supply SG
A19 A14 A9
SG
B19 B14 B9
(Note) : The 5V(P5)DC power supply from the Q173DPX must not be connected if a separated power
supply is used as the Manual pulse generator/Incremental synchronous encoder power supply.
Use a 5V stabilized power supply as a separated power supply. Any other power supply
may cause a failure.
(d) Interface between PULSER connector and tracking enable

signal
Interface between tracking enable signal
Pin No.
Input or
Signal name PULSER connector Wiring example Internal circuit Specification Description
Output 1 2 3
Tracking enable
TREN A4 A3 A2
signal input.
Input Tracking
enable
(Note)
TREN B4 B3 B2
12V to 24VDC
(Note) : As for the connection to tracking enable (TREN +, TREN –), both "+" and "–" are possible.
2 - 59
(6) Connection examples of manual pulse generator

Connection of manual pulse generator Connection of manual pulse generator
(Voltage-output/Open collector type) (Differential-output type)
Q173DPX Manual pulse Q173DPX Manual pulse

Signal name generator side Signal name generator side
HA A HA P A
HB B HA N A
SG 0V HB P B
SG 5V HB N B
(Note-2)
SG (Note-1) SG 0V
P5 P5 5V
(Note-2)
FG shield FG (Note-1)
: 1 to 3 :Twisted pair cable SG
HPSEL
:Twisted pair cable
: 1 to 3
(Note-1) : The 5V(P5)DC power supply from the Q173DPX must not be connected if a separated
power supply is used as the Manual pulse generator/Incremental synchronous
encoder power supply.
Use a 5V stabilized power supply as a separated power supply. Any other power supply
may cause a failure.
(Note-2) : Connect HPSEL to the SG terminal if the manual pulse generator (differential output
type/incremental synchronous encoder is used.
CAUTION
If a separate power supply is used as the manual pulse generator/incremental synchronous
encoder power supply, use a 5V stabilized power supply. Any other power supply may cause a
failure.
2 - 60
2.4.7 Manual pulse generator/Serial absolute synchronous encoder
(1) Table of the Manual pulse generator specifications

Item Specifications
(Note-1)
Model name MR-HDP01
Ambient temperature -10 to 60°C(14 to 140°F)
Pulse resolution 25PLS/rev(100 PLS/rev after magnification by 4)
Voltage-output(power supply voltage -1V or more)/
Output method
Output current = Up to 20mA
(Note-2)
Power supply voltage 4.5 to 13.2VDC
Current consumption 60mA
Life time 1,000,000 revolutions (at 200r/min)
Permitted axial loads Radial load : Up to 19.6N, Thrust load : Up to 9.8N
Mass 0.4kg
Number of max. revolution Instantaneous Up to 600r/min. normal 200r/min
Pulse signal status 2 signals : A phase, B : phase, 90° phase difference
Friction torque 0.1N/m(20°C (68°F) )
(Note-1) : It can be used by combining with Q173DPX.
(Note-2) : If a separate power supply is used, use a stabilized power supply of voltage 5VDC ±
0.25V.
2 - 61
(2) Table of the Serial absolute synchronous encoder specifications

Item Specifications
(Note-1), (Note-2)
Model name Q170ENC
Ambient temperature -5 to 55°C (23 to 131°F)
Resolution 262144PLS/rev
Transmission method Serial communications (Connected to Q172DEX)
Direction of increasing
CCW (viewed from end of shaft)
addresses
Dustproof/Waterproof
Protective construction
(IP65: Except for the shaft-through portion.)
Permitted speed at power ON 3600r/min
Permitted speed at power OFF
(Note-3) 500r/min
Permitted axial loads Radial load : Up to 19.6N, Thrust load : Up to 9.8N

0.02mm(0.00079 inch) or less,
Runout at input shaft tip
(15mm(0.59 inch) from tip)
Recommended coupling Bellows coupling
2
Permitted angular acceleration 40000rad/s
Vibration resistance 5G (50 to 200Hz)
Shock resistance 50G (11ms or less)
Internal current consumption 0.2A
Mass 0.6kg
Q170ENCCBL M
( =Cable length :
Connecting cable
2m(6.56ft.), 5m(16.40ft.), 10m(32.81ft.),
20m(65.62ft.), 30m(98.43ft.), 50m(164.04ft.))
Communications method Differential driver/receiver
Transmission distance Up to 50m(164.04ft.)
(Note-1) : It can be used by combining with Q172DEX.
(Note-2) : When "o-ring" is required, please purchase separately by customers.
(Note-3) : If it exceeds a permitted speed at power OFF, a position displacement is generated.
2 - 62
2.4.8 SSCNET cables and connection method
This section describes how to connect between the Motion CPU module and servo
amplifiers.
Between the Motion CPU module and servo amplifiers is connected by SSCNET
cable. When using the Q172DCPU, only 1 SSCNET cable for connection to servo
amplifier can be used. (Connect to CN1.) When using the Q173DCPU, up to 2
SSCNET cables for connection to servo amplifier can be used. (Connect to CN1 and
CN2.)
Up to 16 servo amplifies can be connected to 1 SSCNET cable.
(However, when using the Q172DCPU, up to 8 servo amplifiers can be connected.)
(1) Connection between the Q173DCPU and servo amplifiers
Q173DCPU Motion CPU module
SSCNET cable length

MR-J3BUS M use
CN1 1) 3m(9.84ft.)
MR-J3BUS M-A use
CN2 1) 20m(65.62ft.)
MR-J3BUS M-B use
1) 50m(164.04ft.)
Attach a cap to
Cap connectors of system
not being used.
SSCNET SYSTEM1
1)
CN1A CN1A
1)
Cap
CN1B
CN1B
Servo amplifier Servo amplifier
SSCNET SYSTEM2
1)
CN1A CN1A
1)
Cap
CN1B
CN1B
(Note): It cannot communicate with that the connection of

CN1A and CN1B is mistaken.
2 - 63
(2) Connection between the Q172DCPU and servo amplifiers

Q172DCPU Motion CPU module
SSCNET cable length

MR-J3BUS M use
1) 3m(9.84ft.)
CN1
MR-J3BUS M-A use
1) 20m(65.62ft.)
MR-J3BUS M-B use
1) 50m(164.04ft.)
1)
CN1A CN1A
1)
Cap
CN1B
CN1B
(Note): It cannot communicate with that the connection of

CN1A and CN1B is mistaken.
List of SSCNET cable model name

Model name (Note) Cable length Description
0.15m(0.49ft.), 0.3m(0.98ft.), 0.5m(1.64ft.), Standard code for

MR-J3BUS M
1m(3.28ft.), 3m(9.84ft.) inside panel
Standard cable for • Q173DCPU/Q172DCPU MR-J3- B

MR-J3BUS M-A 5m(16.4ft.), 10m(32.81ft.), 20m(65.62ft.) • MR-J3- B MR-J3- B
outside panel
MR-J3BUS M-B 30m(98.43ft.), 40m(131.23ft.), 50m(164.04ft.) Long distance cable
(Note) : =cable length
2 - 64
POINTS
(1) Be sure to connect SSCNET cable with the above connector. If the
connection is mistaken, between the Motion CPU module and servo amplifier
cannot be communicated.
(2) SSCNET connector is put a cap to protect light device inside connector from
dust. For this reason, do not remove a cap until just before connecting
SSCNET cable. Then, when removing SSCNET cable, make sure to put a
cap.
(3) Be sure to keep a cap and the tube for protecting light code end of SSCNET
cable in a plastic bag with a zipper of SSCNET cable to prevent them from
becoming dirty.
(4) Do not remove the SSCNET cable while turning on the power supply of
Multiple CPU system and servo amplifier.
Do not see directly the light generated from SSCNET connector of Motion
CPU module or servo amplifier and the end of SSCNET cable. When the
light gets into eye, may feel something is wrong for eye. (The light source of
SSCNET cable complies with class1 defined in JISC6802 or
IEC60825-1.)
(5) When exchanging the servo amplifier or Motion CPU module, make sure to put
a cap on SSCNET connector. When asking repair of servo amplifier or
Motion CPU module for some troubles, make also sure to put a cap on
SSCNET connector. When the connector is not put a cap, the light device
may be damaged at the transit. In this case, exchange and repair of light
device is required.
(3) Cable specifications

(a) MR-J3BUS M
Model name
MR-J3BUS015M MR-J3BUS03M MR-J3BUS05M MR-J3BUS1M MR-J3BUS3M
Item
Cable length [m(ft.)] 0.15(0.49) 0.3(0.98) 0.5(1.64) 1(3.28) 3(9.84)
(b) MR-J3BUS M-A

Model name
MR-J3BUS5M-A MR-J3BUS10M-A MR-J3BUS20M-A
Item
Cable length [m(ft.)] 5(16.40) 10(32.81) 20(65.62)
(c) MR-J3BUS M-B

Model name
MR-J3BUS30M-B MR-J3BUS40M-B MR-J3BUS50M-B
Item
Cable length [m(ft.)] 30(98.43) 40(131.23) 50(164.04)
2 - 65
(4) Setting of the axis No. and axis select switch of servo amplifier
Axis No. is used to set the axis numbers of servo amplifiers connected to
SSCNET connector(CN ) in the program.
Axis No. of 1 to 32 can be set for Q173DCPU, and axis No. of 1 to 8 can be set
for Q172DCPU.
Axis No. is set for each system with SSCNET structure screen of system setting
of MT Developer. Axis No. (Q173DCPU:1 to 32/Q172DCPU:1 to 8) is allocated
and set for the setting axis number (d01 to d16) of servo amplifier.
Since the axis number (d01 to d16) of servo amplifier on the SSCNET structure
screen corresponds to axis select switch (0 to F) of servo amplifier, set the axis
select switch referring to the table of next page.
• SSCNET structure (Allocation of axis No.) • Axis select switch (Servo amplifier)
7 8 9
3 4 5 6
A
B C DE
2
F 0 1
Set the axis No. relative to axis number (dno.).
(Note) : Correspondence between dno. and axis select switch of servo amplifiers is shown in the next
page.
2 - 66
Correspondence between dno.s and axis select switches of servo amplifier

SSCNET Axis select switch SSCNET Axis select switch
dno. (Note) dno. (Note)
system of servo amplifier system of servo amplifier
d01 1 "0" d01 2 "0"
d02 1 "1" d02 2 "1"
d03 1 "2" d03 2 "2"
d04 1 "3" d04 2 "3"
d05 1 "4" d05 2 "4"
d06 1 "5" d06 2 "5"
d07 1 "6" d07 2 "6"
d08 1 "7" d08 2 "7"
d09 1 "8" d09 2 "8"
d10 1 "9" d10 2 "9"
d11 1 "A" d11 2 "A"
d12 1 "B" d12 2 "B"
d13 1 "C" d13 2 "C"
d14 1 "D" d14 2 "D"
d15 1 "E" d15 2 "E"
d16 1 "F" d16 2 "F"
(Note) : The dno. is number of servo amplifier axis displayed with SSCNET structure screen of
MT Developer.
Axis No. is set relative to dno. in the SSCNET structure screen of system settings.
Correspondence between SSCNET system and connector No. of CPU module

is shown below.
Correspondence between SSCNET system No. and connector No. of CPU module
SSCNET system No. Connector No. of CPU
1 SSCNET CN1
2 SSCNET CN2
(Note) : Number of SSCNET systems: Q173DCPU : 2 systems / Q172DCPU : 1 system
2 - 67
2.4.9 External battery
This section describes the battery specifications used in the Motion CPU, handling
precautions and equipments.
(1) External battery specifications(For Motion CPU module)

Model name
Q6BAT
Item
Classification Manganese dioxide lithium primary battery
Initial voltage [V] 3.0
Nominal current [mAh] 1800
Storage life Actually 5 years (Room temperature)
Lithium content [g] 0.49
Applications For memory data backup of SRAM built-in Motion CPU
Exterior dimensions [mm(inch)] 16(0.63)×32(1.26)
(Note) : The 44th Edition of the IATA (International Air Transportation Association) Dangerous Goods Regulations was effected in
January 1st, 2003 and administered immediately.
In this edition, the provisions relating to lithium and lithium ion batteries have been revised to strengthen regulations on
the air transportation of battery.
This battery is not dangerous goods (not class 9). Therefore, these batteries of 24 units or less are not subject to the
regulations.
These batteries more than 24 units require packing based on Packing Instruction 903.
If you need the self-certification form for the battery safety test, contact Mitsubishi.
For more information, contact Mitsubishi.
2 - 68
(2) Data back-up of Motion CPU by the external battery

Be sure to use the external battery.
Set the battery (Q6BAT) to battery holder unit (Q170DBATC).
The programs, parameters, absolute position data, and latch data of SRAM built-
in Motion CPU module are backed up without using the external battery.
In the following status, the backup time after power OFF is 3 minutes.
• The battery connector/Q6BAT lead connector is disconnected.
• The battery cable/lead wire of Q6BAT is broken.
(MIN) (75°C (167°F)) (TYP) (40°C (104°F))
(TYP) (25°C (77°F))
0% 3000 8000 24000
90
30% 4000 11000 34000
Q173DCPU/ External battery (After
50% 6000 16000 43800
Q172DCPU (Q6BAT) SM51/SM52
70% 10000 26000 43800
ON)
100% 43800 43800 43800
(Note-3) : The guaranteed value (MIN) ; equivalent to the total power failure time that is calculated based on the characteristics value of
the memory (SRAM) supplied by the manufacturer and under the storage ambient temperature range of -25°C to 75°C (-13 to
POINTS
The self-discharge influences the life of battery without the connection to Motion
CPU module. The external battery should be exchanged approximately every 4 or
5 years.
CAUTION
Do not short a battery.
Do not charge a battery.
Do not disassemble a battery.
Do not burn a battery.
Do not overheat a battery.
Do not solder the battery terminal.
The programs, parameters, absolute position data and latch data of SRAM built-in Motion
CPU module are backed up without using the external battery.
2 - 69
(3) Connection procedure with Motion CPU module

(a) Set Q6BAT to Battery holder unit(Q170DBATC).
(b) Connect the lead connector of Q6BAT to the connector (BATTERY) of
Q170DBATC.
(c) Connect between the connector (BAT) of Motion CPU module and
connector (CPU) of Q170DBATC.
Motion CPU module
BAT
Battery holder unit
Battery cable (Q170DBATC)
(Q170DBATCBL )
0.5[m]
(1.64[ft.])
Q6BAT
2 - 70
2.4.10 Forced stop input terminal
(1) Table of the forced stop input terminal specifications
Item Specifications
Number of input points Forced stop signal : 1 point
20.4 to 26.4VDC
(+10/ -15%, ripple ratio 5% or less)
ON voltage/current 17.5VDC or more/3.0mA or more
Input resistance Approx. 10k
OFF to ON
Response time 1ms
ON to OFF
2
Applicable wire size 0.3mm (AWG22)
2 - 71
MEMO
2 - 72
3 DESIGN
3. DESIGN
3.1 System Designing Procedure
Design the system which uses the Multiple CPU system in the following procedure.
Motion control system design
Select the Motion CPU module according to number of control axes.
Select the motion functions to be installed according to the machinery 3

and equipment to be controlled (selection of the programming software
packages according to the operating system software).
Select the number of Q172DLX's and design according to the each Refer to section 2.4.4
axis control system and whether servo external signals are required
or not.
When there is mechanical home position and home position return is
made: Proximity dog required
For speed control: Speed-position switching control signal required
When overrun prevention is necessary: Stroke limit required
When each axis stop is necessary: STOP signal required
Select Q173DPX, Q172DEX and design according to whether manual Refer to section 2.4.5
pulse generators and synchronous encoders are required or not. Refer to section 2.4.6
Select interrupt module QI60 according to whether interrupt input are

required or not.
Select I/O modules according to the specifications of the external Refer to MELSEC-Q
equipment to be controlled. series manual.
Select the main base unit, extension base units, extension power Refer to section 2.4.4
supply module and extension cables, and make I/O assignment Refer to section 2.4.5
according to necessary number of Q172DLX's, Q172DEX's, Refer to section 2.4.6
Q173DPX's, QX 's, QY 's and the number of I/O modules.
Select the servo amplifier and servo motor according to the motor Refer to the servo
capacity and number of revolution from the machine mechanism to be amplifier manual.
controlled each axis.
Refer to section 2.4.8

Set the servo amplifier connection by SSCNET and axis numbers
(dno.) and axis No..
3-1
3 DESIGN
Refer to section 3.2

External circuit design
Power supply circuit design

Design the power supply circuit which supplies power to such system
components as the Motion controller, I/O equipment and servo
amplifiers, etc., taking into consideration the protective coordination
and noise suppression techniques.
Safety circuit design

Design the operation-ready circuit which stops the system at
occurrence of any alarm such as a Motion controller or servo amplifier
alarm or the emergency stop, the circuit which avoids a malfunction
while power is unstable at power-on, and the electromagnetic brake
circuit for servomotors.
Layout design within control panel
Refer to section 3.3

Layout design based on the design environment such as temperatures
and vibrations in consideration of heat generated from modules and
handling of module installation.
! CAUTION
Provide appropriate circuits external to the Motion CPU to prevent cases where danger may result
from abnormal operation of the overall system in the event of an external power supply fault or
Motion CPU failure.
Mount the Motion controller, servo amplifier, servomotor and regenerative resistor on
incombustible. Mounting them directly or close to combustibles will lead to fire.
If a fault occurs in the Motion controller or servo amplifier, shut the power OFF at the servo
amplifier’s power source. If a large current continues to flow, fire may occur.
When using a regenerative resistor, shut the power OFF with an error signal. The regenerative
resistor may abnormally overheat due to a fault in the regenerative transistor, etc., and may lead
to fire.
Always take heat measures such as flame proofing for the inside of the control panel where the
servo amplifier or regenerative resistor is mounted and for the wires used. Failing to do so may
lead to fire.
Do not apply a voltage other than that specified in the instruction manual on any terminal. Doing
so may lead to destruction or damage.
3-2
3 DESIGN
! CAUTION
servomotor, etc. while the power is ON and for a short time after the power is turned OFF. In this
Always turn the power OFF before touching the servomotor shaft or coupled machines, as these
parts may lead to injuries.
Do not go near the machine during test operations or during operations such as teaching.
Doing so may lead to injuries.
Always mount a leakage breaker on the Motion controller and servo amplifier power source.
If mounting of an electromagnetic contactor for power shut off during an error, etc., is specified in
the instruction manual for the servo amplifier, etc., always mount the electromagnetic contactor.
Mount an emergency stop circuit externally so that the operation can be stopped immediately and
the power shut off.
Use the Motion controller, servo amplifier, servomotor and regenerative resistor with the correct
combinations listed in the instruction manual. Other combinations may lead to fire or faults.
If safety standards (ex., robot safety rules, etc.,) apply to the system using the Motion controller,
servo amplifier and servomotor, make sure that the safety standards are satisfied.
the system.
In systems where coasting of the servomotor will be a problem during the forced stop, the
emergency stop, servo OFF or when the power is shut OFF, use dynamic brakes.
Make sure that the system considers the coasting amount even when using dynamic brakes.
In systems where perpendicular shaft dropping may be a problem during the forced stop, the
emergency stop, servo OFF or when the power is shut OFF, use both dynamic brakes and
electromagnetic brakes.
The dynamic brakes must be used only during the forced stop, the emergency stop and errors
where servo OFF occurs. These brakes must not be used for normal braking.
The brakes (electromagnetic brakes) assembled into the servomotor are for holding applications,
and must not be used for normal braking.
The system must have a mechanical allowance so that the machine itself can stop even if the
stroke limits switch is passed through at the max. speed.
Use wires and cables that have a wire diameter, heat resistance and bending resistance
compatible with the system.
Use wires and cables within the length of the range described in the instruction manual.
The ratings and characteristics of the parts (other than Motion controller, servo amplifier,
servomotor.
Install a cover on the shaft so that the rotary parts of the servomotor are not touched during
operation.
There may be some cases where holding by the electromagnetic brakes is not possible due to
the life or mechanical structure (when the ball screw and servomotor are connected with a
timing belt, etc.). Mount a stopping device to ensure safety on the machine side.
3-3
3 DESIGN
3.2 External Circuit Design
As to the ways to design the external circuits of the Motion system, this section
explains the method and instructions for designing the power supply circuits and
safety circuits, etc.
(1) Sample system circuit design for motion control 1
3-phase
200/220VAC
Power Supply PLC CPU Motion CPU Input module Output module Servo external
NFB1 Q61P-A2 QnUD(H)CPU Q173DCPU/ signals interface
Q172DCPU QX40 QY10 module
R S T CP1
200VAC Forced stop (Note-1) Q172DX
PYm
EMI.COM Ra1 (Note-2) FLS1
200VAC
Servo normal output
EMI (Servo normal:ON
Alarm:OFF) DOG8/
CHANGE8
FG COM
LG
COM
SSCNET Number of inputs:

8 axes/module
FLS1
DOG8/
CHANGE8
CP2 EMG
24VDC +24V
Power
supply 24G
Emergency Stop
EMG
Operation Ready
CP3 Ra1 OFF ON
MC
MC
SK
3-4
3 DESIGN
POINT
<Example> For control axis 1 and axis 2
(1) (Note-1) : Make the forced stop input cable within 30m(98.43ft.).
The forced stop by the forced stop terminal of input module is also Servo error detection
possible.
(2) (Note-2) : Motion SFC program example is shown in the right record. [F 1]
SET PYm PYm ON with initial
(3) (Note-3) : It is also possible to use a full wave rectified power supply as the (ON : normal)
power supply for the electromagnetic brake. [G 1]
(4) (Note-4) : It is also possible to use forced stop signal of the servo amplifier. M2408+M2428 Servo error detection
of the axis 1, axis 2
(5) (Note-5) : It recommends using one leakage breaker for one servo amplifier.
[F 2]
When electric power is supplied to multiple servo amplifiers for one RST PYm OFF : abnormal (error)
leakage breaker, select the wire connected to the servo amplifier
according to the capacity of the leakage breaker. END
Circuit example when using MR-J3-B

NFB2
(Note-5)
U
L1 MR-J3-B U
V
L2 V SM
W Ra2
L3 A W
Electro-
L11 Ground magnetic
brake
L21 DICOM (Note-3)
SSCNET CN1A ALM Ra2
CN1B EM1
DOCOM
(Note-4)
24VDC
NFB3 Circuit example when using MR-J3-B

(Note-5)
U
L1 MR-J3-B U
V
L2 V SM
W Ra3
L3 B W
Electro-
L11 Ground magnetic
brake
L21 DICOM (Note-3)
CN1A ALM Ra3
CN1B EM1
DOCOM
(Note-4)
24VDC
NFB4 Circuit example when using MR-J3-B

(Note-5)
U
L1 MR-J3-B U
V
L2 V SM
W Ra4
L3 C W
Electro-
L11 Ground magnetic
MC brake
L21 DICOM (Note-3)
CN1A ALM Ra4
CN1B EM1
CP4 DOCOM
(Note-4)
24VDC
(Note-1) : When the control power supply of servo amplifier is shut off, it is not possible to communicate with the servo amplifier after that.
Example) When the control power supply L11/L21 of servo amplifier in above B figure is shut off, it is also not possible to
communicate with the servo amplifier C .
If only a specific servo amplifier power supply is shut off, be sure to shut off the main circuit power supply L1/L2/L3, and do not
shut off the control power supply L11/L21.
(Note-2) : Be sure to shut off the both of main circuit power supply L1/L2/L3 and control power supply L11/L21 at the time of exchange of
servo amplifier. At this time, it is not possible to communicate between the servo amplifier and Motion controller. Therefore, be
sure to exchange the servo amplifier after stopping the operating of machine beforehand.
3-5
3 DESIGN
(2) System design circuit example of the PLC I/O

(a) System design circuit example(when not using ERR terminal
of power supply module)
Power supply
FOR AC FOR AC/DC
Power supply
Transformer Transformer Transformer

Input switched when Fuse Fuse
Fuse power supply established
CPU module
CPU module
SM52
DC power
SM52 Ym
Ym RUN/STOP circuit (-) (+)
SM403
SM403 interlocked with RA1 Yn Fuse
Yn (run monitor relay) XM
Set time for
TM
DC power
Program TM supply to be
START SW N0 MC1 N0 M10 established
RA1
MC M10
MC STOP SW
Program
Input module START SW
RA1
MC
MC STOP SW
RA2
Output module Voltage relay is
Low battery alarm
recommended
Ym (Lamp or buzzer)
RA2 XM
L
ON when run by SM403
Yn
RA1
Low battery alarm

MC Output module (Lamp or buzzer)
Output module
Ym
MC Power to output equipment L ON when run
switched OFF when the Yn
by SM403
STOP signal is given.
RA1
In the case of an emergency
MC2
stop or a stop caused by a
MC1
limit switch. Output module
MC MC
MC1
MC2 Interlock circuits as necessary.
Provide external interlock Power to output
circuits for conflicting equipment switched
operations, such as forward OFF when the STOP
rotation and reverse rotation, signal is given.
MC2
and for parts that could MC1
damage the machine or cause In the case of an
accidents if no interlock were MC1 emergency stop or
used. MC2 a stop caused by
a limit switch.
The power-ON procedure is as follows:

For AC For AC/DC
1) Switch power ON. 1) Switch power ON.
2) Set CPU to RUN. 2) Set CPU to RUN.
3) Turn ON the start switch. 3) When DC power is established, RA2 goes ON.
4) When the magnetic contactor (MC) comes on, the output 4) Timer (TM) times out after the DC power reaches 100[%].
equipment is powered and may be driven by the program. (The TM set value should be the period of time from when
RA2 goes ON to the establishment of 100[%] DC voltage.
Set this value to approximately 0.5 seconds.)
5) Turn ON the start switch.
6) When the electromagnetic contactor (MC) comes on, the
output equipment is powered and may be driven by the
program. (If a voltage relay is used at RA2, no timer (TM) is
required in the program.)
3-6
3 DESIGN
(b) System design circuit example(when using ERR terminal of

power supply module)
Power supply
FOR AC/DC
Transformer Transformer
Input switched
when power supply Fuse Fuse
established.
CPU module
RUN/STOP circuit SM52 DC power

Ym
interlocked with RA1 (-) (+)
(run monitor relay) SM403
Yn Fuse
XM
Set time for DC power
TM supply to be established.
N0 TM
MC1 N0 M10
M10
Program
START SW
RA1 RA3
MC
MC STOP SW
RA2
Voltage relay
is recommended
RA2 XM
output module
Ym Low battery alarm
L (Lamp or buzzer)
Yn
RA1
OFF at ERR contact OFF

Power supply module ERR (stop error occurrence)
RA3
output module MC MC
Interlock circuits as
Output by ERR contact OFF
necessary. Provide
Power OFF of equipment
external interlock
circuits for conflicting
operations, such as
forward rotation and MC2 In the case of an
reverse rotation,
MC1 emergency stop or a
and for parts that could stop caused by a limit
MC1 switch.
damage the machine or MC2
cause accident if no
interlock were used.
The power-ON procedure is as follows:

For AC/DC
1) Switch power ON.
2) Set CPU to RUN.
3) When DC power is established, RA2 goes ON.
4) Timer (TM) times out after the DC power reaches 100[%]. (The TM set value should be the period of time
from when RA2 goes ON to the establishment of 100[%] DC voltage. Set this value to approximately 0.5
seconds.)
5) Turn ON the start switch.
6) When the magnetic contactor (MC) comes on, the output equipment is powered and may be driven by the
program. (If a voltage relay is used at RA2, no timer (TM) is required in the program.)
3-7
3 DESIGN
3.2.1 Power supply circuit design
This section describes the protective coordination and noise suppression techniques of
the power supply circuit.
(1) Separation and protective coordination (leakage current protection,
over current protection) of power supply lines
Separate the lines for Multiple CPU system power supplies from the lines for I/O
devices and servo amplifiers as shown below.
When there is much noise, connect an insulation transformer.
Insulation
Main power PLC power transformer
supply supply
Multiple CPU
100/200VAC
NFB CP system
I/O power T1
supply
I/O devices
CP
Main circuit
power supply
Main circuit device
CP
Servo amplifier
power supply
200VAC Servo amplifier
NFB
(2) Grounding
The Motion system may malfunction as it is affected by various noises such as
electric path noises from the power supply systems, radiated and induced noises
from other equipment, servo amplifiers and their cables, and electromagnetic
noises from conductors. To avoid such troubles, connect the earthing ground of
each equipment and the shield grounds of the shielded cables to the earth.
For grounding, use the exclusive ground terminal wire of each equipment or a
single-point earth method to avoid grounding by common wiring, where possible,
since noises may sneak from other equipment due to common impedances.
100/200VAC Line noise filter Multiple CPU system
SSCNET
Servo-
Servo amplifier motor
(Note): Be sure to ground the line noise filter, Multiple CPU system, servo amplifier and
servomotor. (Ground resistance : 100 or less)
3-8
3 DESIGN
3.2.2 Safety circuit design
(1) Concept of safety circuits

When the Multiple CPU system is powered on and off, normal control output may
not be done momentarily due to a delay or a startup time difference between the
Multiple CPU system power supply and the external power supply (DC in
particular) for the control target.
Also, an abnormal operation may be performed if an external power supply fault
or Motion controller failure takes place.
To prevent any of these abnormal operations from leading to the abnormal
operation of the whole system and in a fail-safe viewpoint, areas which can result
in machine breakdown and accidents due to abnormal operations
(e.g. emergency stop, protective and interlock circuits) should be constructed
outside the Multiple CPU system.
(2) Emergency stop circuit

The circuit should be constructed outside of the Multiple CPU system or servo
amplifier. Shut off the power supply to the external servo amplifier by this circuit,
make the electromagnetic brakes of the servomotor operated.
(3) Forced stop circuit

(a) The forced stop of all servo amplifiers is possible in a lump by using the EMI
forced stop input of Motion CPU modules. After forced stop, the forced stop
factor is removed and the forced stop canceled.
(The servo error detection signal does not turn on with the forced stop.)
The EMI forced stop input cannot be invalidated in the parameter setting of
system setting.
Make the forced stop input cable within 30m(98.43ft.).
The wiring example for the EMI forced stop input of Motion CPU module is
shown below.
Q61P QnUD(H) Q17 D
CPU CPU
EMI.COM
EMI
Forced stop
24VDC
<Motion CPU module>
24VDC (Note-1)
EMI.COM
R
R
EMI
Forced stop
(Note): The EMI forced stop input can be invalidated in the system
settings.
(Note-1): Both of positive common and negative common can be used.
3-9
3 DESIGN
(b) The forced stop of all servo amplifiers is possible in a lump by using the
forced stop input of input modules. After forced stop, the forced stop factor is
removed and the forced stop canceled.
(The servo error detection signal does not turn on with the forced stop.)
The forced stop input can be set by allocation of the device number in the
parameter setting of system setting. When the device is used, apply 24VDC
voltage on EMI terminal and invalidate the forced stop input of EMI terminal.
The wiring example for the forced stop input (QX10) of input module is
shown below.
Q61P QnUD(H) Q17 D QX10
CPU CPU
EMI.COM Xn
EMI
COM
Forced stop
100VAC
24VDC
<Input module QX10>
100VAC
TB17
TB16
LED
Internal
R
R
circuit
TB1
R
Forced stop
(Note): The forced stop input can be set in the system settings.
(c) It is also possible to use the forced stop signal of the servo amplifier.
Refer to manual of the servo amplifier about servomotor capacity.
Operation status of the emergency stop and the forced stop are as follows.
Operation of
Item Remark
the signal ON
Shut off the power supply to the external servo amplifier
Emergency stop
by external circuit, make the servomotor stopped.
Servo OFF
The servomotor is stopped according to the stop
Forced stop
instruction from Motion controller to the servo amplifier.
3 - 10
3 DESIGN
3.3 Layout Design within The Control Panel
3.3.1 Mounting environment
Mount the Motion controller system in the following environment conditions.
(1) Ambient temperature is within the range of 0 to 55°C (32 to 131°F) .
(2) Ambient humidity is within the range of 5 to 95[%]RH.
(3) No condensing from sudden temperature changes
(4) No corrosive or inflammable gas
(5) There must not be a lot of conductible dust, iron filings, oil mist, or salt, organic
solvents.
(6) No direct sunlight
(7) No strong electrical or magnetic fields
(8) No direct vibrations or shocks on the Motion controller
3 - 11
3 DESIGN
3.3.2 Layout design of the base units
This section describes the precautions related to mount a Motion controller in

an enclosure.
(1) To improve ventilation and permit easy replacement of the module, leave a space
of the following table between the top, bottom, side of the module and any other
object.
(For details on layout design refer to section 4.1.2 "Instructions for mounting of the
base unit".)
• Top 40mm (1.57inch) or more

• Bottom 100mm (3.94inch) or more
• Front 100mm (3.94inch) or more
• Side 5mm (0.20inch) or more
(2) Provide a wiring duct, if required.
! CAUTION
Due to ventilation problems, do not mount the base units vertically or horizontally.
Mount the base units on a flat surface. Unevenness or warping of the surface can apply undue
force to printed circuit boards and lead to operation failures.
Avoid mounting the base units close to a vibration source, such as a large electromagnetic
contactor or no-fuse breaker. Mount them on a separate panel or at a safe distance.
To limit the effects of reflected noise and heat, leave 100mm(3.94inch) or more clearance to
instruments fitted in front of the Motion controller (on the rear of the door).
Similarly, leave 50mm(1.97inch) or more clearance between instruments and the left and right
sides of the base units.
3 - 12
3 DESIGN
3.3.3 Calculating heat generation by Motion controller
The ambient temperature inside the panel storing the Motion controller must be
suppressed to an ambient temperature of 55°C(131°F) or less, which is specified for
the Motion controller.
For the design of a heat releasing panel, it is necessary to know the average power
consumption (heating value) of the devices and instruments stored inside.
Here the method of obtaining the average power consumption of Q173DCPU/
Q172DCPU system is described. From the power consumption, calculate a rise in
ambient temperature inside the control panel.
How to calculate average power consumption
The power consuming parts of the Motion controller are roughly classified into six
blocks as shown below.
(1) Power consumption of power supply module

The power conversion efficiency of the power supply module is approx. 70[%],
while 30 [%] of the output power is consumed as heat. As a result, 3/7 of the
output power is the power consumption.
Therefore the calculation formula is as follows.
3
Wpw= (I5V 5) [W]
7
I5V: Current consumption of logic 5 VDC circuit of each module
(2) Total power consumption for 5VDC logic circuits of all modules
(including CPU module)
The power consumption of the 5 VDC output circuit section of the power supply
module is the power consumption of each module (including the current
consumption of the base unit).
W5V = I5V 5 [W]
(3) A total of 24 VDC average power consumption of the output

module
The average power of the external 24 VDC power is the total power consumption
of each module.
W24V = I24V 24 Simultaneous ON rate [W]
I24V: Average current consumption of 24VDC power supply for internal
consumption of the output module [A]
(Power consumption for simultaneous ON points)
(4) Average power consumption due to voltage drop in the output

section of the output module
WOUT = IOUT Vdrop Number of outputs Simultaneous ON rate [W]
IOUT : Output current (Current in actual use) [A]
Vdrop : Voltage drop in each output module [V]
3 - 13
3 DESIGN
(5) Average power consumption of the input section of the input

module
WIN = IIN E Number of input points Simultaneous ON rate [W]
IIN : Input current (Effective value for AC) [A]
E : Input voltage (Voltage in actual use) [V]
(6) Power consumption of the external power supply section of the

intelligent function module
WS = I5V 5 + I24V 24 + I100V 100 [W]
The total of the power consumption values calculated for each block is the power
consumption of the overall sequencer system
W = W PW + W5V + W 24V + WOUT + WIN + WS [W]
From this overall power consumption [W], calculate the heating value and a rise
in ambient temperature inside the panel.
The outline of the calculation formula for a rise in ambient temperature inside the
panel is shown below.
W
T= [C]
UA
W : Power consumption of overall Motion system (value obtained above)
2
A : Surface area inside the panel [m ]
U : When the ambient temperature inside the panel is uniformed by a fan ...... 6
When air inside the panel is not circulated.............................................. 4
POINT
If the temperature inside the panel has exceeded the specified range, it is
recommended to mount a heat exchanger to the panel to lower the temperature.
If a normal ventilating fan is used, dust will be sucked into the Motion controller
together with the external air, and it may affect the performance of the Motion
controller.
3 - 14
3 DESIGN
(7) Example of average power consumption calculation

(Q173DCPU use)
(a) System configuration
Q38DB
Q61P Q03UD Q173D QX40 QX40 Q172D Q172D Q173D QY10 QY10
CPU CPU LX EX PX
(b) 5 VDC current consumption of each module

(Note)
Q03UDCPU : 0.33 [A]
Q173DCPU : 1.25 [A]
(Note)
QX40 : 0.05 [A]
Q172DLX : 0.06 [A]
Q172DEX : 0.19 [A]
Q173DPX : 0.38 [A]
(Note) (Note) : 5VDC internal current consumption of shared
QY10 : 0.43 [A] equipments with PLC might be changed.
(Note)
Q38DB : 0.228 [A] Be sure to refer to the PLC Manuals.
(c) Power consumption of power module

WPW = 3/7 (0.33 + 1.25 + 0.05 + 0.05 + 0.06 + 0.19 + 0.38 + 0.43 + 0.43 +
0.228) 5 = 7.28 [W]
(d) Power consumption of a total of 5 VDC logic section of each module

W5V = (0.33 + 1.25 + 0.05 + 0.05 + 0.06 + 0.19 + 0.38 + 0.43 + 0.43 +
0.228) 5) = 16.99 [W]
(e) A total of 24 VDC average power consumption of the output module

W24V = 0 [W]
(f) Average power consumption due to voltage drop in the output section of the
output module
WOUT = 0 [W]
(g) Average power consumption of the input section of the input module
WIN = 0.004 24 32 1 = 3.07 [W]
(h) Power consumption of the power supply section of the intelligent function
module.
WS = 0 [W]
(i) Power consumption of overall system

W = 7.28 + 16.99 + 0 + 0 + 3.07 + 0 = 27.34 [W]
3 - 15
3 DESIGN
3.4 Design Checklist
At the worksite, copy the following table for use as a check sheet.
Item Sub Item Design confirmation Check

Motion CPU module Number of axes axes
selection Motion CPU module selection
PLC CPU module Number of I/O points points
selection PLC CPU module selection
Manual pulse generator pcs.
Synchronous encoder pcs.
Upper limit point points
Lower limit point points
STOP input point points
Motion module
Proximity dog input point points
selection
Speed switching input point points
Module Tracking enable signal point points
selection Q172DLX modules
Q172DEX modules
Q173DPX modules
Motion CPU module modules
Main base unit I/O module/intelligent function module installed to
modules
selection main base,
Main base unit selection
Number of I/O modules/intelligent function
modules
Extension base unit modules installed to extension base,
and extension cable Distance between Main base and extension base mm
selection Extension base unit selection
Extension cable selection
External Avoidance of operation failure at power-on
Fail-safe circuit design
circuit design Avoidance of hazard at Motion controller failure
Conformance with general specifications such as ambient
temperature, humidity, dust, etc.
Total power consumption of base unit
Layout W
Module layout design (Calculate the heating value)
design
Layout in consideration of clearances between enclosure's inside
walls, other structures and modules and heats generated by
modules within the control panel.
3 - 16
4 INSTALLATION AND WIRING
4. INSTALLATION AND WIRING
4.1 Module Installation
4.1.1 Instructions for handling
CAUTION
Use the Motion controller in an environment that meets the general specifications contained in this
manual. Using this Motion controller in an environment outside the range of the general specifications
could result in electric shock, fire, operation failure, and damage to or deterioration of the product.
While pressing the installation lever located at the bottom of module, insert the module fixing tab into
the fixing hole in the base unit until it stops. Then, securely install the module with the fixing hole as a
supporting point. Incorrect installation of the module can cause an operation failure, failure or drop.
When using the Motion controller in the environment of much vibration, tighten the module with a screw. 4
Tighten the screw in the specified torque range. Under tightening may cause a drop, short circuit or
operation failure. Over tightening may cause a drop, short circuit or operation failure due to damage to
the screw or module.
Be sure to connect the extension cable to connectors of the base unit correctly. After connecting,
check them for looseness. Poor connections could cause an input or output failure.
Completely turn off the externally supplied power used in the system before installation or removing
the module. Not doing so could result in electric shock or damage to the product.
Do not install/remove the module onto/from base unit or terminal block more than 50 times, after the
first use of the product. Failure to do so may cause the module to malfunction due to poor contact of
connector.
This section describes instructions for handling the CPU, I/O, intelligent function and
power supply modules, base units and so on.
(1) Module, terminal block connectors and pin connectors are made of resin; do not
drop them or subject them to strong impact.
(2) Do not remove modules' printed circuit boards from the enclosure in order to avoid
changes in operation.
(3) Tighten the module fixing screws and terminal block screws within the tightening
torque range specified below.
Location of screw Tightening torque range
Motion CPU module fixing screw (M3 13 screw) 0.36 to 0.48 N•m
Module fixing screw (M3 12 screw) 0.36 to 0.48 N•m
I/O module terminal block screw (M3 screw) 0.42 to 0.58 N•m
I/O module terminal block fixing screw (M3.5 screw) 0.68 to 0.92 N•m
Power supply module terminal screw (M3.5 screw) 0.68 to 0.92 N•m
4-1
(4) Be sure to install a power supply module on the main base unit and extension
base unit. Even if the power supply module is not installed, when the I/O modules
and intelligent function module installed on the base units are light load type, the
modules may be operated. In this case, because a voltage becomes unstable, we
cannot guarantee the operation.
(5) When using an extension cable, keep it away from the main circuit cable (high
voltage and large current).
Keep a distance of 100mm or more from the main circuit.
(6) Be sure to fix a main base unit to the panel using fixing screws. Not doing so could
result in vibration that may cause erroneous operation.
Mount a main base unit in the following procedure.

(a) Fit the two base unit top mounting screws into the enclosure.
Panel
(b) Place the right-hand side notch of the base unit onto the right-hand side
screw.
Panel
(c) Place the left-hand side pear-shaped hole onto the left-hand side screw.
Panel
(d) Fit the mounting screws into the holes at the bottom of the base unit, and
then retighten the all mounting screws.
(Note) : Mount a main base unit to a panel, with no module installed in the right-
end slot.
Remove the base unit after removing the module from the right-end slot.
4-2
4.1.2 Instructions for mounting the base unit
When mounting the Motion controller to an enclosure or similar, fully consider its
operability, maintainability and environmental resistance.
(1) Fitting dimensions

Fitting dimensions of each base unit are as follows:
5-fixing screw (M4 14)
OUT
5V
SG
Hs 2
H
POWER CPU I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 II/O11
/ O11
FG Q312DB
Hs1
Ws1 Ws2 Ws3
Q38DB Q312DB Q63B Q65B Q68B Q612B

W 328 (12.91) 439 (17.28) 189 (7.44) 245 (9.65) 328 (12.91) 439 (17.28)
Ws1 15.5 (0.61)
170 ± 0.3 170 ± 0.3 190 ± 0.3 190 ± 0.3
Ws2
(6.69 ± 0.01) (6.69 ± 0.01) 167 ± 0.3 222.5 ± 0.3 (7.48 ± 0.01) (7.48 ± 0.01)
138 ± 0.3 249 ± 0.3 (6.57 ± 0.01) (8.76 ± 0.01) 116 ± 0.3 227 ± 0.3
Ws3
(5.43 ± 0.01) (9.80 ± 0.01) (4.57 ± 0.01) (8.93 ± 0.01)
H 98 (3.86)
Hs1 7 (0.28)
Hs2 80 ± 0.3 (3.15 ± 0.01)
[Unit: mm (inch)]
4-3
(2) Module mounting position

Keep the clearances shown below between the top/bottom faces of the module
and other structures or parts to ensure good ventilation and facilitate module
replacement.
(Note): It is impossible to mount the main base unit by DIN rail.
Top of panel or wiring duct Base unit
40mm
Motion CPU module Motion CPU module
(1.58inch)
MELSEC
Q61P
POWER
Q03DCPU
MODE
Q173DCPU
QX40
01 2 3 4 5 6 7
89 AB CDE F
QX40
0 1 2 3 45 6 7
8 9 A B CDE F
Q172DEX
SY. ENC TREN
1 1
Q173DPX
PLS.A PLS. B TREN
1 1 1
or more
RUN 2 2
2 2 2
ERR. 3 3 3
USER SW
BAT. 1 2
BOOT STOP RUN
CAUTION
EMI
SY. ENC1
PULSER II/O11
/ O1 1
PULL
Q312DB
CN1
USB
PULL
Panel Door
CN2
RS-232
FRONT
BAT
Q172DEX Q173DPX
100mm
(3.94inch)
100mm 123.5mm or more
(3.94inch) (4.86inch)
or more
5mm(0.20inch) 5mm(0.20inch)
or more (Note-1) or more
(Note-1) : 20mm (0.79 inch) or more when the adjacent module is not removed and the extension cable is connected.
(3) Module mounting orientation

(a) Mount the Motion controller in the orientation shown below to ensure good
ventilation for heat release.
(b) Do not use it in either of the orientations shown below.
Vertical Flat Upside down
(4) Mounting surface

Mount the base unit on a flat surface. If the mounting surface is not even, this
may strain the printed circuit boards and cause malfunctions.
4-4
(5) Mounting of unit in an area where the other devices are mounted
Avoid mounting base unit in proximity to vibration sources such as large
magnetic contractors and no-fuse circuit breakers; mount those on a separate
panel or at a distance).
(6) Distances from the other devices

In order to avoid the effects of radiated noise and heat, provide the clearances
indicated below between the Motion controller and devices that generate noise or
heat (contactors and relays).
• In front of Motion controller : 100 mm (3.94 inch) or more
• On the right and left of Motion controller : 50 mm (1.97 inch) or more
50mm(1.97inch)
or more
100mm(3.94inch)
50mm(1.97inch)
or more
or more
Contactor, relay, etc.
4-5
4.1.3 Installation and removal of module
This section explains how to install and remove a power supply module, PLC CPU
module, Motion CPU module, Motion module, I/O module, intelligent function module
or another module to and from the base unit.
(1) Installation and removal of the module from Q3 DB,Q6 B

(a) Installation of the module on Q3 B and Q6 B
Securely insert the module Base unit

Base unit
fixing protection into the
module fixing hole so that the
latch is not misaligned. Module
connector
Module
fixing hook
Using the module fixing hole Module loading
as a fulcrum, push the module Module lever
in the direction of arrow to Module fixing hole
install it into the base unit.
Module Module
fixing hook fixing hook
Make sure that the module is Module Module fixing hole

installed in the base unit loading
securely. lever
Module fixing hole
When using module in a place (Note)

where there is large vibration
or impact, install them by the
unit fixing screws.
Base unit
Base unit
Unit fixing
END projection
Module
fixing hook
Module fixing hole
(Note): Screw the Motion CPU module to the main base unit.
4-6
POINTS
(1) When installing the module, always insert the module fixing projection into the
module fixing hole of the base unit.
At that time, securely insert the module fixing projection so that it does not
come off from the module fixing hole.
If the module is forcibly installed without the latch being inserted, the module
connector and module will be damaged.
(2) When using the modules in a place where there is large vibration or impact,
screw the module to the base unit.
Module fixing screw : M3 12 (user-prepared)
Screw the Motion CPU module to the main base unit using supplied fixing
screws.
(3) Do not install/remove the module onto/from base unit or terminal block more
than 50 times, after the first use of the product. Failure to do so may cause the
module to malfunction due to poor contact of connector.
CAUTION
Insert the module fixing projection into the fixing hole in the base unit to install the module.
Incorrect installation could result in malfunction, failure, or a drop of the module.
When using the modules in a place where there is large vibration or impact, screw the module
to the base unit.
Tighten the screws within the specified torque range.
If the screw is too loose, it may cause a drop of the module, a short circuit or malfunctions.
If too tight, it may cause damage to the screws and/or module, resulting in an accidental drop of
the module, short circuit or malfunctions.
4-7
(b) Removal from Q3 DB and Q6 B
Push
When using the module fixing
screws, remove them.
Module fixing hook

Support the module with both
hands and securely press the
module fixing hook with your
finger.
Base unit
Module Module
connector
Pull the module based on the
supporting point of module
bottom while pressing the
module fixing hook. Module fixing hole
While lifting a module, take off

the module fixing projection
from the module fixing hole. Lifting
Pull
Completion
POINT
When the module fixing screw is used, always remove the module by removing the
module fixing screw and then taking the module fixing latch off the module fixing
hole of the base unit.
Attempting to remove the module by force may damage the module fixing latch.
CAUTION
Do not touch the heat radiating fins of controller or servo amplifier's, regenerative resistor and
servomotor, etc. while the power is ON and for a short time after the power is turned OFF. In
this timing, these parts become very hot and may lead to burns.
Remove the modules while paying attention.
4-8
4.1.4 Instructions for mounting of the battery holder unit
When mounting the battery holder unit (Q170DBATC) to an enclosure or similar, fully
consider its mounting position and orientation.
(1) Module mounting position

Mount the battery holder unit within 50cm(1.64ft.) or less (Battery cable length:
50cm(1.64ft.)) from the Motion controller.
(2) Mounting surface

Mount the battery holder unit on a flat surface.
(3) Module mounting orientation

Do not mount the battery holder unit downward. Doing so may lead to battery
liquid to leak at damage to the battery.
(Correct) (Wrong)
CPU
Q170DBATC
BATTERY
LITHIUM BATTERY
MITSUBISHI
LITHIUM BATTERY
MITSUBISHI
BATTERY
Q170DBATC
CPU
Q170DBATC
BATTERY
CPU
LITHIUM BATTERY
MITSUBISHI MITSUBISHI
LITHIUM BATTERY
BATTERY
CPU
Q170DBATC
4-9
4.2 Connection and disconnection of Cable
4.2.1 SSCNET cable
(1) Precautions for handling the SSCNET cable

• Do not stamp the SSCNET cable.
• When laying the SSCNET cable, be sure to secure the minimum cable bend
radius or more. If the bend radius is less than the minimum cable bend radius, it
may cause malfunctions due to characteristic deterioration, wire breakage, etc.
Model name of SSCNET cable Minimum bend radius[mm(inch)]
MR-J3BUS M 25(0.98)
Enforced covering cord: 50 (1.97)
MR-J3BUS M-A
Code : 25 (0.98)
Enforced covering cord: 50 (1.97)
MR-J3BUS M-B
Code : 30 (1.18)
• For connection and disconnection of SSCNET cable, hold surely a tab of

cable connector.
• Refer to Section 4.4.3. for wiring precautions.
Motion CPU
module
CN1
CN2
(2) Connection of SSCNET cable

• For connection of SSCNET cable to the Motion CPU module, connect it to the
SSCNET connector CN1 or CN2 of Motion CPU module while holding a tab
of SSCNET cable connector. Be sure to insert it until it clicks.
• If the code tip for the SSCNET cable is dirty, optical transmission is
interrupted and it may cause malfunctions. If it becomes dirty, wipe with a
bonded textile, etc. Do not use solvent such as alcohol.
(3) Disconnection of SSCNET cable

• For disconnection of SSCNET cable, pull out it while holding a tab of
SSCNET cable connector or the connector.
• After disconnection of SSCNET cable, be sure to put a cap (attached to
Motion CPU module or servo amplifier) to the Motion CPU module and servo
amplifier.
• For SSCNET cable, attach the tube for protection optical code's end face on
the end of connector.
4 - 10
POINTS
(1) Forcibly removal the SSCNET cable from the Motion CPU module will
damage the Motion CPU modules and SSCNET cables.
(2) After removal of the SSCNET cable, be sure to put a cap on the SSCNET
connector. Otherwise, adhesion of dirt deteriorates in characteristic and it may
cause malfunctions.
(3) Do not remove the SSCNET cable while turning on the power supply of
Multiple CPU system and servo amplifier.
Do not see directly the light generated from SSCNET connector of Motion
CPU module or servo amplifier and the end of SSCNET cable. When the
light gets into eye, may feel something is wrong for eye. (The light source of
SSCNET cable complies with class1 defined in JISC6802 or
IEC60825-1.)
(4) If the SSCNET cable is added a power such as a major shock, lateral
pressure, haul, sudden bending or twist, its inside distorts or brakes, and
optical transmission will mot be available.
Be sure to take care enough so that the short SSCNET cable is added a
twist easily.
(5) Be sure to use the SSCNET cable within the range of operating temperature
described in this manual. Especially, as optical fiber for MR-J3BUS M and
MR-J3BUS M-A are made of synthetic resin, it melts down if being left near
the fire or high temperature. The cable part and code part melt down if being
left near the fire or high temperature. Therefore, do not make it touched the
part which becomes high temperature, such as radiator or regenerative brake
option of servo amplifier, or servomotor.
(6) When laying the SSCNET cable, be sure to secure the minimum cable bend
radius or more.
(7) SSCNET cable is used a optical cables or optical codes little affected by
plasticizer. However, come migrating plasticizer may affect the optical
characteristic of SSCNET cable as shown below.
SSCNET cable Code Cable
MR-J3BUS M
MR-J3BUS M-A
MR-J3BUS M-B
Cable is not affected by plasticizer.
Phthalate ester plasticizer such as DBP and DOP may affect optical characteristic
of cable.
4 - 11
POINTS
(8) Put the SSCNET cable in the duct or fix the cable at the closest part to the
Motion CPU module with bundle material in order to prevent SSCNET cable
from putting its own weight on SSCNET connector.
When laying cable, the optical cord should be given loose slack to avoid from
becoming smaller than the minimum bend radius, and it should not be twisted.
Also, fix and hold it in position with using cushioning such as sponge or rubber
which does not contain plasticizing material.
(9) If the adhesion of solvent and oil to the code part of SSCNET cable may
lower the optical characteristic and machine characteristic. If it is used such an
environment, be sure to do the protection measures to the cord part.
(10) When keeping the Motion CPU or servo amplifier, be sure to put on a cap to
connector part so that a dirt should not adhere to the end of SSCNET
connector.
(11) SSCNET connector is put a cap to protect light device inside connector from
dust. For this reason, do not remove a cap until just before connecting
SSCNET cable. Then, when removing SSCNET cable, make sure to put a
cap.
(12) Be sure to keep a cap and the tube for protecting light code end of SSCNET
cable in a plastic bag with a zipper of SSCNET cable to prevent them from
becoming dirty.
(13) When exchanging the servo amplifier or Motion controller, make sure to put a
cap on SSCNET connector. When asking repair of servo amplifier or Motion
controller for some troubles, make also sure to put a cap on SSCNET
connector. When the connector is not put a cap, the light device may be
damaged at the transit. In this case, exchange and repair of light device is
required.
4 - 12
4.2.2 Battery cable
(1) Handling the battery cable

(a) Precautions for handling the battery cable
• For connection or removal of the battery cable, do it surely while holding a
connector.
Base unit Motion CPU module
Bottom
Front
Control panel
Connector for CPU side

Battery connector
(BAT)
Do not hold
lead wire
Connector for battery side
CPU connector (CPU)

Battery holder unit
(Q170DBATC)
(b) Connection of the battery cable

• For connection of a connector to the Motion CPU module, connect it surely
to the battery connector (BAT) of Motion CPU module while holding a
connector. Be sure to insert it until it clicks.
• For connection of a connector to the battery holder unit, connect it surely to
the CPU connector (CPU) of battery holder while holding a connector. Be
sure to insert it until it clicks
4 - 13
(c) Removal of the battery cable

• For removal of the battery cable, pull out it while holding a connector.
(2) Handling the battery lead wire

(a) Precautions for handling the battery lead wire
• For connection or removal of the battery lead wire, do it surely while
holding a battery lead connector.
Do not hold
lead wire
Battery Battery lead connector

lead wire
Connector (BATTERY)
Q6BAT
Battery holder unit
(Q170DBATC)
(b) Connection of the battery lead wire

• For connection of a battery (Q6BAT) to the battery holder unit, connect it
surely to a connector (BATTERY) of battery holder unit while holding a
battery lead connector. Be sure to insert it until it clicks.
(c) Removal of the battery lead wire

• For removal of the battery lead wire, pull out it while holding a battery lead
connector.
POINT
(1) Forcibly removal the battery cable or battery lead wire from the battery holder
unit will damage the battery holder unit, battery cable or battery lead wire.
(2) As for the battery cable, the shape of connector is different on Motion CPU
side and battery holder side. Be sure to connect after confirming shape.
(3) The programs, parameters, absolute position data, and latch data of SRAM
built-in Motion CPU module are backed up if the battery connector is not
connect correctly.
4 - 14
4.2.3 Forced stop input cable
(1) Precautions for handling the forced stop input cable

• For connection or removal of the forced stop input cable, do it surely while
holding a connector of forced stop input cable.
Motion CPU module
Removal
1)
2)
(2) Connection of the forced stop input cable

• For connection of a forced stop input cable to the Motion CPU module, connect
it surely to a EMI connector of Motion CPU module while holding a connector.
Be sure to insert it until it clicks.
(3) Removal of the forced stop input cable

• For removal of the forced stop input cable, pull out it while holding a connector.
POINTS
Forcibly removal the forced stop input cable from the CPU module will damage the
Motion CPU unit or forced stop input cable.
4 - 15
4.3 Mounting of Serial Absolute Synchronous Encoder
This section describes precautions for handling the serial absolute synchronous
encoder (Q170ENC).
(1) If the serial absolute synchronous encoder is linked to a chain, timing belt, or
gears, the machine rotating shaft should be supported by a separate bearing
and connected to Q170ENC through a coupling. Ensure that excessive force
(greater than the permitted shaft load) is not applied to the shaft of Q170ENC.
Table 4.1 Permitted Shaft Loads

Gear
Bearing
Q170ENC Radial direction Thrust direction
Coupling
Permitted shaft load Up to 19.6N Up to 9.8N
Fig. 4.1 Example of Encoder Linked to a Gear
(2) Excessive load is applied to the shaft of Q170ENC by the large mounting errors in
eccentricity and angle of deviation As a result, it might damage the machine or
shorten extremely the life.
Minimize loads applied to the shaft such that they make within the permitted shaft
load range.
4 - 16
CAUTION
The Q170ENC contains a glass disk and precision mechanism. Take care when handling it. The
encoder performance may deteriorate if it is dropped or subjected to shocks or vibration exceeding the
prescribed limits.
Do not connect the shaft of Q170ENC directly to machine side rotary shaft. Always after connecting
the shaft of Q170ENC to another bearing once, connect the shaft through a flexible coupling.
Gear
Bearing
Q170ENC
Coupling
Fig 4.2 Connecting the shaft of Q170ENC to a machine side rotary shaft.
Never hit the end of the Q170ENC coupling shaft with a hammer when connecting the coupling to it.
The large loads applied to Q170ENC will damage it.
The Q170ENC uses optical parts. Mount it in an atmosphere where there are extremely few water
drops and little oil and dust.
In any place where the Q170ENC is exposed to water and/or oil, provide protection from oil and water,
e.g. install a cover. In addition, run the cable downward to prevent oil and/or water from running on the
cable into the Q170ENC. When it is inevitable to mount the Q170ENC vertically or obliquely, trap for
the cable.
Use the Q170ENC within the specified temperature range (-5 to 55°C (23 to 131°F) ).
4 - 17
4.4 Wiring
4.4.1 Instructions for wiring
DANGER
the module. Not doing so could result in electric shock or damage to the product.
When turning on the power supply or operating the module after wiring, be sure that the module's
terminal covers are correctly attached. Not attaching the terminal cover could result in electric shock.
CAUTION
Be sure to ground of the earth terminal FG and LG. Not doing so could result in electric shock or
operation failure. (Ground resistance: 100 or less)
When wiring in the Motion controller, be sure that it is done correctly by checking the product's rated
voltage and the terminal layout. Connecting a power supply that is different from the rating or
incorrectly wiring the product could result in fire or damage.
External connections shall be crimped or pressure welded with the specified tools, or correctly
soldered. Imperfect connections could result in short circuit, fire, or operation failure.
Tighten the terminal screws within the specified torque range. If the terminal screws are loose, it could
result in short circuit, fire, or operation failure. Tightening the terminal screws too far may cause
damages to the screws and/or the module, resulting in drop, short circuit, or operation failure.
Be sure there are no foreign matters such as sawdust or wiring debris inside the module. Such debris
could cause fire, damage, or operation failure.
The module has an ingress prevention label on its top to prevent foreign matter, such as wiring debris,
from entering the module during wiring.
Do not remove this label during wiring.
Before starting system operation, be sure to remove this label because of heat dissipation.
This section described instructions for the wiring of the power supply.
(1) Power supply wiring
(a) 100VAC, 200VAC and 24VDC wires should be twisted as dense as possible
respectively. Connect the modules with the shortest distance.
Also, to reduce the voltage drop to the minimum, use the thickest wires (Up
2
to 2.0mm ) possible.
Use the wires of the following core size for wiring.
Application Recommended core size
100VAC, 200VAC, 24VDC wires 2.0mm2 or less
2
0.3 to 0.75mm
I/O equipment
(Outside diameter 2.8mm (0.11inch) or less)
Ground wire 2.0mm2 or more
4 - 18
(b) Do not bundle the 100VAC and 24VDC wires with, or run them close to, the
main circuit (high voltage, large current) and I/O signal lines (including
common line).
Reserve a distance of at least 100mm (3.94inch) from adjacent wires.
(c) As measures against serge caused by lightening, connect a surge absorber

for lightening as shown below.
Multiple CPU
AC
system
E2
E1 Surge absorber for thunder
POINTS
(1) Separate the ground of the surge absorber for lighting (E1) from that of the
Multiple CPU system (E2).
(2) Select a surge absorber for lighting whose power supply voltage does no
exceed the maximum allowable circuit voltage even at the time of maximum
power supply voltage elevation.
(2) Wiring of I/O equipment

(a) Insulation-sleeved crimping terminals cannot be used with the terminal
block.
It is recommended to cover the wire connections of the crimping terminals
with mark or insulation tubes.
(b) The wires used for connection to the terminal block should be 0.3 to
2
0.75mm in core and 2.8mm (0.11inch) or less in outside diameter.
(c) Run the input and output lines away from each other.
(d) When the wiring cannot be run away from the main circuit and power lines,
use a batch-shielded cable and ground it on the Motion controller side.
In some cases, ground it in the opposite side.
Multiple CPU system
Shield cable
Input
RA
Output Shield
DC
(e) Where wiring runs through piping, ground the piping without fail.
(f) Run the 24VDC input line away from the 100VAC and 200VAC lines.
4 - 19
(g) Wiring of 200m (656.17ft.) or longer distance will give rise to leakage
currents due to the line capacity, resulting in a fault.
Refer to the troubleshooting chapter of the I/O Module User's Manual.
(h) As a countermeasure against the power surge due to lightning, separate the
AC wiring and DC wiring and connect a surge absorber for lightning (Refer
to Section 4.4.1(1)).
Failure to do so increases the risk of I/O device failure due to lightning.
(3) Grounding
For grounding, follow the steps (a) to (c) shown below.
(a) Use a dedicated grounding wire as far as possible.
(Ground resistance: 100 or less)
(b) When a dedicated grounding cannot be performed, use (2) Common

Grounding shown below.
Multiple CPU Another Multiple CPU Another Multiple CPU Another

system equipment system equipment system equipment
grounding grounding
(1) Independent grounding.....Best (2) Common grounding.....Good (3) Joint grounding.....Not allowed
2
(c) For grounding a cable, use the cable of 2 mm or more.
Position the ground-contact point as nearly to the Multiple CPU system as
possible, and reduce the length of the grounding cable as much as possible.
4 - 20
4.4.2 Connecting to the power supply module
The following diagram shows the wiring example of power lines, grounding lines, etc.
to the main and extension base units.
Main base unit

100/110VAC (Q38DB)
AC Q61P CPU module
Fuse
(Note-1)
ERR
AC
DC FG
24VDC
LG
INPUT
100-240VAC
Ground
Connect to 24VDC terminals wire
of I/O module that requires Grounding
24VDC internally.
Extension base unit
Extension cable (Q68B)
Q61P I/O module
100VAC
(Note-1)
ERR
FG
LG
INPUT
100-240VAC
Ground
wire
Grounding
(Note) : The operation of the ERR terminal is as follows.

<When the power supply module is installed on the main base unit>
The terminal turns OFF (opens) when the AC power is not input, a CPU module stop error
(including a reset) occurs, or the fuse of the power supply module is blown.
<When the power supply module is installed on the extension base unit>
The terminal is always OFF(open).
4 - 21
POINT
2
(1) Use the thickest possible (up to 2mm ) wires for the 100/200 VAC and 24 VDC
power cables. Be sure to twist these wires starting at the connection terminals.
To prevent a short circuit should any screws loosen, use solderless terminals
with insulation sleeves of 0.8 mm (0.03 inch) or less.
Also, only two solderless terminals can be connected per terminal block.
Terminal
block
Solderless terminals
with insulation sleeves
(2) Ensure that the earth terminals LG and FG are grounded.

(Ground resistance : 100 or loss)
Since the LG terminal has a half of the input voltage, touching this terminal may
result in an electric shock.
(3) No system error can be detected by the ERR terminal of an extension base
unit. (The ERR terminal is always set off.)
4 - 22
4.4.3 Precautions of SSCNET cable wiring
SSCNET cable is made from optical fiber. If optical fiber is added a power such as a
major shock, lateral pressure, haul, sudden bending or twist, its inside distorts or
breaks, and optical transmission will not be available. Especially, as optical fiber for
MR-J3BUS M, MR-J3BUS M-A is made of synthetic resin, it melts down if being left
near the fire or high temperature. Therefore, do not make it touched the part, which
becomes high temperature, such as radiator or regenerative brake option of servo
amplifier.
Be sure to use optical fiber within the range of operating temperature described in this
manual.
Read described item of this section carefully and handle it with caution.
(1) Minimum bend radius

Make sure to lay the cable with greater radius than the minimum bend radius. Do
not press the cable to edges of equipment or others. For SSCNET cable, the
appropriate length should be selected with due consideration for the dimensions
and arrangement of Motion controller or servo amplifier. When closing the door of
control box, pay careful attention for avoiding the case that SSCNET cable is
hold down by the door and the cable bend becomes smaller than the minimum
bend radius.
Model name of SSCNET cable Minimum bend radius[mm(inch)]
MR-J3BUS M 25(0.98)
Enforced covering cord : 50 (1.97)
MR-J3BUS M-A
Code : 25 (0.98)
Enforced covering cord : 50 (1.97)
MR-J3BUS M-B
Code : 30 (1.18)
(2) Tension
If tension is added on the SSCNET cable, the increase of transmission loss
occurs because of external force which concentrates on the fixing part of
SSCNET cable or the connecting part of SSCNET connector. At worst, the
breakage of SSCNET cable or damage of SSCNET connector may occur.
For cable laying, handle without putting forced tension. (Refer to "APPENDIX1.1
SSCNET cables" for the tension strength.)
(3) Lateral pressure

If lateral pressure is added on the SSCNET cable, the cable itself distorts,
internal optical fiber gets stressed, and then transmission loss will increase. At
worst, the breakage of optical cable may occur. As the same condition also
occurs at cable laying, do not tighten up SSCNET cable with a thing such as
nylon band (TY-RAP).
Do not trample it down or tuck it down with the door of control box or others.
4 - 23
(4) Twisting
If the SSCNET cable is twisted, it will become the same stress added condition
as when local lateral pressure or bend is added. Consequently, transmission loss
increases, and the breakage of optical fiber may occur at worst.
(5) Disposal
When incinerating optical cable (cord) used for SSCNET , hydrogen fluoride gas
or hydrogen chloride gas which is corrosive and harmful may be generated. For
disposal of optical fiber, request for specialized industrial waste disposal services
who has incineration facility for disposing hydrogen fluoride gas or hydrogen
chloride gas.
(6) Wiring process of SSCNET cable

Put the SSCNET cable in the duct or fix the cable at the closest part to the
Motion CPU module with bundle material in order to prevent SSCNET cable
from putting its own weight on SSCNET connector.
Leave the following space for wiring.
• Putting in the duct

Top of panel or wiring duct Base unit
40mm
Motion CPU module Motion CPU module
(1.58inch)
MELSEC
Q61P
POWER
Q03DCPU
MODE
Q173DCPU
QX40
01 2 3 4 5 6 7
89 AB CDE F
QX40
0 1 2 3 45 6 7
8 9 A B CDE F
Q172DEX
SY. ENC TREN
1 1
Q173DPX
PLS.A PLS. B TREN
1 1 1
or more
RUN 2 2
2 2 2
ERR. 3 3 3
USER SW
BAT. 1 2
BOOT STOP RUN
CAUTION
EMI
SY. ENC1
PULSER II/O11
/ O1 1
PULL
Q312DB
CN1
USB
PULL
Panel Door
CN2
RS-232
FRONT
BAT
Q172DEX Q173DPX
100mm
(3.94inch)
100mm 123.5mm or more
(3.94inch) (4.86inch)
or more
5mm(0.20inch) 5mm(0.20inch)
or more (Note-1) or more
(Note-1) : 20mm (0.79 inch) or more when the adjacent module is not removed and the extension cable is connected.
4 - 24
• Bundle fixing
Optical cord should be given loose slack to avoid from becoming smaller than the minimum bend radius, and it
should not be twisted. When laying cable, fix and hold it in position with using cushioning such as sponge or
rubber which does not contain plasticizing material.
Base unit Motion controller
Control panel
Code
Loose slack
Bundle material Cable

Recommended product
NK clamp SP type (NIX,INC.)
4 - 25
MEMO
4 - 26
5 TRIAL OPERATION AND ADJUSTMENT
5. TRIAL OPERATION AND ADJUSTMENT
5.1 Checklist before Trial Operation
Table 5.1 Checklists before Trial Operation

Model name Confirmation Items Check Reference
(1) Check that the main base unit is Q38DB or Q312DB. 2.4.3
(2) Check that the model name of module is correct. 2.2
(3) Check that the installation order is correct. 2.1.4
(4) Check that the damage for installed modules.
(5) Check that the modules are installed correctly. 4.1.3
Main base unit/
Extension base unit (6) Check for looseness, rattling or distorted installation. 4.1.1
(7) Check that the module fixing screw tightening torque is as specified. 4.1.1
Refer to the "Q173DCPU/
(8) Check that the total I/O points of I/O modules and intelligent function Q172DCPU" Motion
modules do not exceed the I/O points of the CPU module. controller Programming
Manual(COMMON)"
(1) Check that the model name of power supply modules is correct. 2.4.2
(2) Check that the wire sizes of cables are correct. 4.4.1
(3) Check that the power line is wired correctly. 4.4.1
(4) Check that FG and LG are wired correctly. 4.4.2 5
(5) Check that the terminal screws are tightened correctly.
Power supply module (6) Check that the terminal screws are tightening torque is as specified. 4.1.1
(7) Check that the 100VAC, 200VAC and 24VDC wires are twisted as
4.4.1
closely as possible respectively and run in the shortest distance.
(8) Check that the 100VAC, 200VAC and 24VDC wires are not bind the
4.4.1
cable together with and run close to the power wires.
(9) Check that grounding of the earth terminal FG and LG. 4.4.2
2.1.4
(1) Check that the model name of PLC CPU modules is correct.
2.2
PLC CPU module
(2) Check that the modules are installed to CPU slot or I/O slot 0 to 2 of
2.1.4
the main base unit.
(1) Check that the Q173HCPU(-T)/Q172HCPU(-T)/Q173CPUN(-T)/
2.1.4
Q173CPUN(-T)/Q173CPU/Q172CPU is not used.
(2) Check that the modules are installed to I/O slot 0 to 2 of the main
2.1.4
Q173DCPU/Q172DCPU base unit.
Motion CPU module (3) Check that the module fixing screws are tightened correctly. 4.1.1
(4) Check that the EMI forced stop input is wired correctly. 3.2
(5) Check that the external battery is installed.
(6) Check that the battery cables are connected correctly. 4.2.2
(1) Check that the wire size of cable is correct.
(2) Check that the terminal block screws are tightened correctly.
Refer to the I/O Module
(3) Check that the cables connected to each terminal of terminal block
Type Building Block
correspond to the signal names.
User's Manual
(4) Check that the external power supply are connected correctly.
I/O module (24VDC, 5 VDC)
(5) Check that the 100VAC, 200VAC and 24VDC wires are twisted as
4.4.1
closely as possible respectively and run in the shortest distance.
(6) Check that the 100VAC, 200VAC and 24VDC wires are not bind the
4.4.1
cable together with and run close to the I/O wires.
(7) Check that the I/O wires are wired correctly. 4.4.1
5-1
Model name Confirmation Items Check Reference

(1) Check that the Q172DEX is installed to I/O slot 3 to 11 of the
2.1.4
main base unit.
(2) Check that the Q172DLX/Q173DPX is installed to I/O slot 3
Q172DLX Servo external signals 2.1.4
to 11 when installation to the main base unit.
interface module/ Refer to the programming
(3).Check that the installation position of modules correspond to
Q172DEX synchronous encoder manual of operating
the system setting.
interface module/ system software.
Q173DPX Manual pulse generator 2.4.4
(4) Check that the connection with external equipments is
interface module 2.4.5
correct.
2.4.6
(5) Check that the battery is connected to connector of
6.4.2
Q172DEX correctly.
(1) Check that the model name of SSCNET cables is correct.
(2) Check that the connecting position for connector of 2.4.8
SSCNET cables are correct.
(3) Check that the SSCNET cables are connected correctly. 4.2.1
SSCNET cable (4) Check for looseness, rattling or distorted connection. 4.4.3
(5) Check that the minimum bend radius or more secured. 4.4.3
(6) Check that the codes do not come in contact with wires/
cables that use materials where the plasticizing material is 4.2.1
contained.
(1) Check that the lead connector of Q6BAT is connected to the
4.2.2
connector (BATTERY) correctly.
(2) Check that the mounting orientation is correct.
4.1.4
(Do not mount it downward.)
Battery holder unit (Q170DBATC)
(3) Check that the battery cable is connected correctly. 4.2.2
(4) Check for looseness, rattling or distorted mounting. 4.1.4
(5) Check that the module fixing screw tightening torque is as
4.1.1
specified.
(1) Check that the amplitude, eccentricity and axial
displacement relative to the machine side rotary shaft are 4.3
within the permissible values.
Serial absolute synchronous
(2) Check that a flexible coupling is used for coupling with the
encoder unit (Q170ENC) 4.3
machine side rotary shaft.
(3) Check that the damage for units.
(4) Check that the forcible impact is given on modules. 4.3
5-2
5.2 Trial Operation and Adjustment Procedure

The mode indicated in the brackets [ ] at top left of
Servo start-up procedure each step is the mode for checking or setting using
MT Developer.
Turn OFF Multiple CPU system power supply

PLC CPU Check that the power supply of Multiple
Motion CPU CPU system is OFF.
Check wiring and module installation Refer to Section 2.1.4 for installation method and
installation position.
(1) Check the installation position and
condition of each modules. Refer to Section 4.1.3 for installation of module.
(2) Check the connecting condition of
connectors. DANGER
(3) Check that all terminal screws are tight. Be sure to ground the Motion controllers, servo
(4) Check the ground wires of servo amplifiers and servomotors.
amplifier, etc.. (Ground resistance: 100 or less)
(5) Check the servomotor wiring (U, V, W). Do not ground commonly with other devices.
(6) Check the regenerative resistor wiring.
(7) Check the circuit of emergency stop or CAUTION
forced stop.
Check that the installation position of modules
and combination of modules are correct.
Wrong installation and combination may damage
the modules.
[Installation mode]
Install operating system software Refer to Section 5.3
Motion CPU : The operating system software is not installed at
Install the operating system software to
the CPU module using MT Developer. the time of Motion CPU module purchase.
Be sure to install the operating system software to
be used before a system start.
Servo amplifier setting Refer to Section 2.4.8(4)
Servo amplifier
Set the axis number of servo amplifier.
CAUTION
When using a regenerative resistor, shut the
Turn ON power supply power OFF with an error signal. The
regenerative resistor may abnormally overheat
PLC CPU Set the RUN/STOP/RESET switch of PLC
CPU module to STOP, and turn ON the due to a fault in the regenerative transistor, etc.,
Motion CPU and may lead to fires.
Multiple CPU power supply.
Always take heat measure such as flame
proofing for the inside of the control panel where
[System setting] the servo amplifier or regenerative resistor is
Multiple CPU parameters setting mounted and for the wires used. Failing to do so
may lead to fires.
Set the following positioning parameters
Motion CPU using MT Developer.
(1) Multiple CPU setting
(2) Automatic refresh setting
(3) System setting
[Parameter setting]
PLC parameter setting
PLC CPU Set the parameter setting using
GX Developer.
1)
5-3
1)
(Note) : An error may occur if the power is turned on
before system setting. In the case, reset the
Turn ON power supply again Multiple CPU system after system setting.
Turn ON again the power supply or reset Refer to the "Q173DCPU/Q172DCPU Motion
of Multiple CPU system. controller Programming Manual (COMMON)"
at the system setting error occurrence.
Check external inputs to Q172DLX Refer to Section 2.4.4
Check the wiring of following external

inputs by monitoring of MT Developer.
(1) FLS (Upper stroke limit input)
(2) RLS (Lower stroke limit input)
(3) STOP (Stop signal)
Check external inputs to Q172DEX Refer to Section 2.4.5

Check the wiring of following external
inputs by monitoring of MT Developer or
LED indicators.
(1) Serial absolute synchronous encoder
setting
Check external inputs to Q173DPX Refer to Section 2.4.6

Motion CPU Check the wiring of following external
inputs by monitoring of MT Developer or
LED indicators.
(1) Manual pulse generator/incremental
synchronous encoder setting
Check I/O module

CAUTION
Do not mount a phase advancing capacitor,
Check the wiring of I/O module. surge absorber or radio noise filter (option FR-
BIF) on the output side of the servo amplifier.
Correctly connect the output side (terminal U, V,
W). Incorrect connections will lead the
[Servo data setting] servomotor to operate abnormally.
Positioning parameters setting
Set the following positioning parameters
using MT Developer. CAUTION
(1) Fixed parameters Set parameter values to those that are
(2) Servo parameters compatible with the Motion controller, servo
(3) Home position return data amplifier, servomotor and regenerative resistor
model name and the system name application.
(4) Limit switch
The protective functions may not function if the
settings are incorrect.
2)
5-4
2) DANGER
Never open the front case or terminal cover at
[Programming] times other than wiring work or periodic
inspections even if the power is OFF. The
Create Motion programs insides of the Motion controller and servo
Motion CPU Create the Motion programs using amplifier are charged and may lead to electric
shocks.
MT Developer.
When performing wiring work or inspections,
turn the power OFF, wait at least ten minutes,
[Programming] and then check the voltage with a tester, etc..
Create PLC programs Failing to do so may lead to electric shocks.
Create the PLC programs to start of Wire the units after mounting the Motion
Motion programs using GX Developer. controller, servo amplifier and servomotor.
Failing to do so may lead to electric shocks or
damage.
PLC CPU
Write PLC programs

CAUTION
Write the PLC programs created to the
PLC CPU module. Always mount a leakage breaker on the Motion
controller and servo amplifier power source.
Install emergency stop circuit externally so that

operation can be stopped immediately and the
Write Motion programs power shut off.
Write the positioning data and Motion Use the program commands for the program
Motion CPU with the conditions specified in the instruction
programs created to the Motion CPU
module. manual.
Some devices used in the program have fixed
applications, so use these with the conditions
specified in the programming manual.
Turn ON power supply again
Turn ON again or reset the Multiple CPU
system power supply .
CAUTION
If safety standards (ex., robot safety rules, etc., )
apply to the system using the Motion controller,
servo amplifier and servomotor, make sure that
Turn ON servo amplifiers power supply
the safety standards are satisfied.
Check the emergency stop ON and forced Construct a safety circuit externally of the
stop ON, and turn ON the power supply of Motion controller or servo amplifier if the
servo amplifiers and servomotors. abnormal operation of the Motion controller or
servo amplifier differ from the safety directive
[Test mode operation in the system.
servo start-up
(Initial check) ]
Check servo am plifier Axis No. and error description of servo amplifier which
detected errors are displayed on initial check screen.
Check that the mounted servo amplifiers
operate correctly.
[Test mode
Motion CPU servo start-up
(Upper/lower stroke
limit check) ]
Check upper/lower stroke limits
Check that the upper/lower stroke limits
operate correctly.
3)
5-5
3)
[Test mode
JOG operation ]
Check machine operation
CAUTION
Check the followings by making the machine
operate with the JOG operation of The system must have a mechanical
MT Developer. allowance so that the machine itself can stop
(1) Machine operates correctly
even if the stroke limits switch is passed
(no vibration, hunting, etc. )
(2) Stroke limits operate correctly through at the max. speed.
(3) Machine stops by the emergency stop Execute the test operation in the system that
or forced stop. it is low-speed as much as possible and put
forced stop, and confirm the operation and
[Test mode safety.
home position return ]
Check home position return
Check the followings by executing the home
position return.
(1) Home position return direction
(2) Home position return data
(3) Proximity dog position
Motion CPU
[Programming]
Check Motion program
Set the RUN/STOP/RESET switch of PLC
CPU module to RUN and the RUN/STOP
switch of Motion CPU module to RUN, and
check that all positioning controls by Motion
programs are correct.
[Monitor]
Check by automatic operation
PLC CPU Check the sequence operation by executing

the PLC program using an actual external
input.
END
POINTS
(1) Make note of motor module names before the motor is mounted on a machine.
The motor name plate may not be visible after the motor is mounted.
(2) When the servo amplifier, servomotor is first turned on, check the operation
before the servomotor is mounted on a machine to avoid an unexpected
accidents such as machine breakage.
5-6
5.3 Operating System Software Installation Procedure
The operating system software must be installed to the Motion CPU module by using
the peripheral device and MT Developer.
The installation procedure is shown below.
START
Set a rotary switch1 (SW1) of Motion Set to installation mode.

CPU module to "A".
(Rotary switch 2 (SW2) is optional.) Refer to Section 2.4.1(3) for rotary switch.
Shipped from the factory in

SW1 "A, SW2 "0" position.
Turn ON the Multiple CPU system Steady "INS" display.

power supply. RUN/STOP switch is ignored.
Install the operating system software

using MT Developer.
Turn OFF the Multiple CPU system

power supply.
Set a rotary switch1 (SW1) and switch2

Set to mode operated by RAM.
(SW2) of Motion CPU module to "0".
END
POINTS
(1) The operating system software was not installed at the time of Motion CPU
module purchase. Be sure to install the operating system software to be used
before a system start.
(2) Be sure to change a rotary switch after turning off the power supply.
(3) Even if the operating system software is installed, the programs, parameters
and absolute position data written in the Motion CPU module does not be
rewritten.
(4) Do not turn off the power supply during installation. Doing so could result
damage the Motion CPU module.
(5) When the operating system software is installed at set the multiple Motion
CPU modules not installed in one base unit, be sure to set to installation mode
(set a rotary switch1 (SW1) to "A" position.) of all not installed Motion CPU
modules to install.
(Note): If the power supply is turned ON without setting all Motion CPU module
not installed to installation mode, it does not operate normally.
Be sure to install the operating system software before system start.
5-7
5.4 Trial Operation and Adjustment Checklist
At the worksite, copy the following table for use as a check sheet.
Work Step Item Trial Operation and Adjustment Confirmation Check
Check that the each module is installed correctly.
Check that the each connector is connected correctly.
Check the each terminal screw for looseness.
Check that the earth wires of power supply module or servo amplifiers, etc. are
Installation of
Before power supply correct.
unit/module
ON Check that the servomotor wiring is correct.
and basic wiring
Check that the regenerative option wiring is correct.
Check that the circuit of emergency stop and forced stop are correct.
Check that the wiring of each power supply and I/O are correct.
Check that the rotary switch setting is correct.
Installation of OS Check that the operating system software is compatible.
System setting Check that the system setting is correct.
Power supply ON/
Check that the upper/lower stroke limit inputs are correct.
Q172LX external
Check that the STOP signal input is correct.
Motion CPU module signal
Check that the proximity dog and speed/position switching signal input are correct.
in STOP status/
Program/ Check that the Motion program, PLC program and positioning data are stored in the
positioning data PLC/Motion CPU module correctly.
PLC CPU module in
Check the communications with servo amplifiers.
STOP status
Check that the rotation direction for JOG operation is correct.
Check that the upper/lower limit switches operate correctly.
Basic axis Check that the rotation at maximum command speed is motor rating or less.
Motion CPU module
operations Check that the machine operates correctly by the JOG operation.
in RUN status/
(Check each axis) Check that the machine stops by the upper/lower stroke limit.
Check that the machine stops by the emergency stop or forced stop.
PLC CPU module in
Check that the home position return is executed correctly.
STOP status
Check that each positioning control of Motion program is operates correctly.
Check the each operation in manual operation mode of system during Motion program
execution.
Check that the machine operation stops immediately by the emergency stop or
forced stop.
Manual operation
Check the operation of each actuator and confirmation limit switch.
Check that the emergency stop, forced stop and equipment alarm signals are
correct.
Checks in compliance with control specifications specific to system and equipment.
Motion CPU module Check the each operation in manual operation mode of system during Motion program
in RUN status/ execution.
Check that the automatic operation motions.
PLC CPU module in
Check that the machine operation stops immediately by the emergency stop or
RUN status
Automatic forced stop.
operation Check that the module or equipment alarm causes an immediate stop or cycle
stop.
Check that the restoring operation can be performed after an alarm stop.
Make other checks in compliance with control specifications specific to system and
equipment.
Check that the acceleration/deceleration torque is maximum torque or less.
Torque check
Check that the continuous effective load torque is rated torque or less.
5-8
6 INSPECTION AND MAINTENANCE
6. INSPECTION AND MAINTENANCE
DANGER
Do not touch the terminals while power is on. Doing so could cause electric shock.
Correctly connect the battery. Also, do not charge, disassemble, heat, place in fire, short circuit, or
solder the battery.
Mishandling of a battery may cause overheating, cracks or ignition which could result in injury and fire.
Switch off all phases of the externally supplied power used in the system when cleaning the
module or retightening the terminal or module mounting screws.
Not doing so could result in electric shock.
Under tightening of terminal screws can cause a short circuit or malfunction.
Over tightening of screws can cause damages to the screws and/or the module, resulting in
fallout, short circuits, or malfunction.
The capacitor is mounted to the modules. Do not incinerate the modules so that the incineration of
capacitor may cause burst.
CAUTION
Read the manual carefully and pay careful attention to safety for the on-line operation (especially
program change, forced stop or operation change) performed by connecting peripheral devices to the
CPU module during operation. 6
Erroneous operation may cause machine breakage or accident.
Never try to disassemble or modify module. It may cause product failure, operation failure, injury or fire.
Use any radio communication device such as a cellular phone or a PHS phone more than 25cm (9.85
inch) away in all directions of the Motion controller.
Failure to do so may cause a malfunction.
the module. Not doing so could result in damage to the product.
Do not install/remove the module on to/from base unit or terminal block more than 50 times, after the
first use of the product. Failure to do so may cause the module to malfunction due to poor contact of
connector.
Do not drop or impact the battery installed to the module. Doing so may damage the battery, causing
battery liquid to leak in the battery.
Do not use the dropped or impacted battery, but dispose of it.
Before touching the module, always touch grounded metal, etc. to discharge static electricity from
Do not directly touch the module's conductive parts and electronic components. Touching them could
cause an operation failure or give damage to the module.
In order that you can use the Motion controller in normal and optimal condition at all times, this
section describes those items that must be maintained or inspected daily or at regular intervals.
6-1
6.1 Maintenance Works
6.1.1 Instruction of inspection works
In order that can use the Motion controller in safety and normal, those items that must
be inspected list below.
DANGER
Never open the front case or terminal covers while the power is ON or the unit is running, as this may
lead to electric shocks.
Never run the unit with the front case or terminal cover removed. The high voltage terminal and
charged sections will be exposed and may lead to electric shocks.
Never remove the front case or terminal cover at times other than wiring work or periodic inspections
even if the power is OFF. The insides of the Motion controller and servo amplifier are charged and
When performing wiring work or inspections, turn the power OFF, wait at least ten minutes, and then
check the voltage with a tester, etc.. Failing to do so may lead to electric shocks.
Never operate the switches with wet hands, as this may lead to electric shocks.
Do not damage, apply excessive stress, place heavy things on or sandwich the cables, as this may
lead to electric shocks or fire.
Do not touch the Motion controller, servo amplifier or servomotor terminal blocks while the power is
ON, as this may lead to electric shocks.
Do not touch the built-in power supply, built-in grounding or signal wires of the Motion controller and
servo amplifier, as this may lead to electric shocks.
CAUTION
Be sure to ground the Motion controller, servo amplifier and servomotor. Do not ground
commonly with other devices. (Ground resistance : 100 or less)
The wiring work and inspections must be done by a qualified technician.
Wire the units after mounting the Motion controller, servo amplifier and servomotor. Failing to do so
may lead to electric shocks or damage.
Perform the daily and periodic inspections according to the instruction manual.
Perform maintenance and inspection after backing up the program and parameters for the Motion
controller and servo amplifier.
Do not place fingers or hands in the clearance when opening or closing any opening.
Periodically replace consumable parts such as batteries according to the instruction manual.
Do not touch the lead sections such as ICs or the connector contacts.
Do not place the Motion controller or servo amplifier on metal that may cause a power leakage or
wood, plastic or vinyl that may cause static electricity buildup.
Do not perform a megger test (insulation resistance measurement) during inspection.
When replacing the Motion controller or servo amplifier, always set the new unit settings correctly.
After maintenance and inspections are completed, confirm that the position detection of the
absolute position detector function is correct.
6-2
CAUTION
Do not short circuit, charge, overheat, incinerate or disassemble the batteries.
The electrolytic capacitor will generate gas during a fault, so do not place your face near the Motion
controller or servo amplifier.
The electrolytic capacitor and fan will deteriorate. Periodically change these to prevent secondary
damage from faults. Replacements can be made by our sales representative.
If an error occurs in the self diagnosis of the Motion controller or servo amplifier, confirm the check
details according to the instruction manual, and restore the operation.
If a dangerous state is predicted in case of a power failure or product failure, in order to prevent that
state, use a servomotor with electromagnetic brakes for maintenance or mount a brake mechanism
externally.
Use a double circuit construction so that the electromagnetic brake operation circuit can be operated
by emergency stop signals set externally.
Shut off with the
Shut off with servo ON signal OFF, emergency stop
alarm, electromagnetic brake signal. signal (EMG).
Servomotor
RA1 EMG
Electromagnetic
brakes
24VDC
If an error occurs, remove the cause, secure the safety and then resume operation after alarm
release.
The unit may suddenly restart after a power failure is restored, so do not go near the machine. (Design
the machine so that personal safety can be ensured even if the machine restarts suddenly.)
Confirm and adjust the program and each parameter before operation. Unpredictable movements may
occur depending on the machine.
Extreme adjustments and changes may lead to unstable operation, so never make them.
Do not apply a voltage other than that specified in the instruction manual on any terminal.
Doing so may lead to destruction or damage.
Do not mistake the terminal connections, as this may lead to destruction or damage.
servomotor, etc., while the power is ON and for a short time after the power is turned OFF. In this
Always turn the power OFF before touching the servomotor shaft or coupled machines, as these parts
may lead to injuries.
Do not go near the machine during test operations or during operations such as teaching. Doing so
may lead to injuries.
Do not bunch the control wires or communication cables with the main circuit or power wires, or
lay them closely. They should be installed 100 mm (3.94 inch) or more from each other.
Trying to bunch or install could result in noise that would cause operation failure.
6-3
6.2 Daily Inspection
The items that must be inspected daily are shown below.

Table 6.1 Daily Inspection
Item Inspection item Inspection Criterion Action
Check that the fixing
Retighten the
1 Mounting of base unit screws are not loose and The screws and cover must be mounted securely.
screws.
the cover is not dislocated.
Check that the module is
Securely engaged
Installation of I/O not dislocated and the unit The module fixing hook must be engaged and installed
2 the module fixing
module fixing hook is engaged correctly.
hook.
securely.
Check for loose terminal Retighten the
Screws should not be loose.
screws. terminal screws.
Check for distance between The proper clearance should be provided between
3 Connecting conditions Correct.
solderless terminals. solderless terminals.
Retighten the
Check the connector part of
Connections should not be loose. connector fixing
the cable.
screws.
Power supply module
The LED must be ON (green).

[POWER] LED Check that the LED is ON.
(Abnormal if the LED is OFF or ON (red)).
Refer to
"QCPU User's
Manual (Function
Explanation,
The LED must be ON (green).
[MODE] LED Check that the LED is ON. Program Funda-
PLC CPU module
(Abnormal if the LED is OFF or flickering.)

mentals)".
Check that the LED is ON The LED must be ON.
[RUN] LED
in RUN status. (Abnormal if the LED is OFF.)
The LED must be OFF.
[ERR.] LED Check that the LED is OFF.
Module indication LED
(Abnormal if the LED is ON or flickering.)

The LED must be OFF.
[BAT.] LED Check that the LED is OFF.
(Abnormal if the LED is ON.)
Steady "RUN" display.
(Abnormal if "RUN" does not display or incorrect display.)
Refer to Section
Normal
2.4.1(2)
Steady "STP" display.
4 (Abnormal if "STP" does not display or incorrect display.)
Motion CPU module
Battery error
"BT1" does not display.
warning
(Abnormal if steady "BT1" display.)
(2.7V or less) Refer to Section
Battery error 6.5
"BT2" does not display.
warning
(Abnormal if steady "BT2" display.)
(2.5V or less)
" . . . " does not display.
WDT error
(Abnormal if steady " . . ." display.)
Refer to Section
2.4.1(2)
" AL" does not flash.
Others
(Abnormal if " . . ." flashes.)
The LED must be ON when the input power is turned ON.

Module indication LED
Check that the LED is The LED must be OFF when the input power is turned OFF.
Input LED ON/OFF. (Abnormal if the LED does not turn ON or turn OFF as Refer to
I/O module
indicated above.) "I/O Module Type

Building Block
The LED must be ON when the input power is turned ON.
Check that the LED is The LED must be OFF when the input power is turned OFF. User's Manual".
Output LED
ON/OFF. (Abnormal if the LED does not turn ON or turn OFF as
indicated above.)
6-4
6.3 Periodic Inspection
The items that must be inspected one or two times every 6 months to 1 year are listed
below. When the equipment is moved or modified, or layout of the wiring is changed,
also implement this inspection.
Table 6.2 Periodic Inspection

Item Inspection item Inspection Judgment criteria Remedy
Ambient environment
Ambient temperature 0 to 55 °C (32 to 131 °F)

When the controller is used in
Measure with a thermometer and a the board, the ambient
1 Ambient humidity hygrometer. 5 to 95 % RH temperature in the board
Measure corrosive gas. becomes the ambient
temperature.
Atmosphere No corrosive gases
Measure a voltage across the 85 to 132VAC

2 Power voltage terminals of 100/200VAC and 170 to 264VAC Change the power supply.
24VDC. 15.6 to 31.2VDC
Retighten the screws.
Move the module to check for The module must be installed If the CPU, I/O, or power supply
Installation
Looseness, rattling
looseness and rattling. solidly. module is loose, fix it with
3
screws.
Adhesion of dirt and Dirt and foreign matter must not
Check visually. Remove and clean.
foreign matter be present.
Looseness of terminal Try to further tighten screws with a
Screws must not be loose. Retighten the terminal screws.
screws screwdriver.
Connection
Proximity of solderless Solderless terminals must be

4 Check visually. Correct.
terminals to each other positioned at proper intervals.
Looseness of Retighten the connector fixing
Check visually. Connectors must not be loose.
connectors screws.
Check the 7-segment LED at the Must be turned OFF "BT1" or Even if the lowering of a battery
front side of CPU module. "BT2" display. capacity is not shown, replace
the battery with a new one if a
Check the length of term after Must not be used more than 5 service life time of the battery is
5 Battery purchasing the battery years. exceeded.
Check that SM51 or SM58 is
Replace the battery with a new
turned OFF using MT Developer in Must be turned OFF.
one when SM51 or SM58 is ON.
monitor.
6-5
6.4 Life
The following parts must be changed periodically as listed below.

However, if any part is found faulty, it must be changed immediately even when it has
not yet reached the end of its life, which depends on the operating method and
environmental conditions.
For parts replacement, please contact your sales representative.
Table 6.3 Life

Module name Part name Life guideline Remark
Motion CPU module Super capacitor Life guideline is reference time.

10 years
Motion module Electrolytic capacitor It must be changed immediately
Synchronous Super capacitor even when it has not yet
2 to 3 years reached the life guideline.
encoder Bearings
(1) The life of the capacitor greatly depends on ambient temperature and operating
conditions. The capacitor will reach the end of its in 10 years of continuous
operation in normal air-conditioned environment.
(2) Change the bearings in 20,000 to 30,000 hours as a guideline under rated speed.
This differs on the operating conditions, The bearings must also be changed if
unusual noise or vibration is found during inspection.
6-6
6.5 External Battery
The battery installed in the Motion CPU module is used for data retention during the
power failure of the program memory and latch device. Special relays SM51 or SM58
turn on due to the decrease of battery voltage. Even if the special relays turn on, the
program and retained data are not erased immediately.
However, if these relays are overlooked, the contents may be erased.
After relay SM51 or SM58 turns on, replace the battery quickly within the data
retention time for power failure (3 minutes).
POINT
(1) SM51 or SM58 turns on when the battery voltage falls below the specified
value, and remains ON even after the voltage is recovered to the normal
value. SM51 or SM58 turns off by power supply on again or reset.
(2) After SM51 or SM52 turns on, replace the battery quickly.
• SM51 turns on at the battery voltage 2.5V or less.
• SM58 turns on at the battery voltage 2.7V or less.
(3) If SM51 turns on, the details of the programs, parameters and absolute
position data cannot be guaranteed.
It is recommended to back-up the battery periodically.
6-7
6.5.1 Battery life
(1) Q173DCPU/Q172DCPU, Q172DEX module battery life

The battery life is shown below.
(MIN) (75°C (167°F)) (TYP) (40°C (104°F))
(TYP) (25°C (77°F))
0% 20000
90
30% 27000
Q173DCPU/ External battery (Q6BAT) (After
(Note-7) 50% 31000 43800 43800
Q172DCPU SM51/SM52
70% 36000
ON)
100% 43800
0% 3000 8000 24000
30% 4000 11000 34000
Q170ENC 1 50% 6000 16000 43800
Internal 70% 10000 26000 43800 40
battery 100% 43800 43800 43800 (After Error
Q172DEX
(A6BAT/ 0% 1500 4000 12000 code 1152
MR-BAT) 30% 2000 5500 17000 occurrence)
Q170ENC 2 50% 3000 8000 21900
70% 5000 13000 21900
100% 43800 43800 43800
(Note-3) : The guaranteed value (MIN) ; equivalent to the total power failure time that is calculated based on the characteristics value of the
memory (SRAM) supplied by the manufacturer and under the storage ambient temperature range of -25°C to 75°C (-13 to
(Note-6) : In the following status, the backup time after power OFF is 3 minutes.
(Note-7) : Set the battery (Q6BAT) to battery holder unit (Q170DBATC).
6-8
POINT
(1) Do not use the battery exceeding its guaranteed life.
(2) When the battery hours (total power failure time) may exceed its guaranteed
value, take the following measure.
• Perform ROM operation to protect a program even if the battery dies at the
Multiple CPU system power-OFF.
• If SM51 or SM52 turns on, the contents of programs, parameters and
absolute position data cannot be guaranteed.
(3) When the battery-low special relay SM52 turns on, immediately change the
battery. Even if the alarm has not yet occurred, it is recommended to replace
the battery periodically according to the operating condition
(4) The self-discharge influences the life of battery without the connection to
Q173DCPU/Q172DCPU/Q172DEX. The external battery should be exchanged
approximately every 4 or 5 years.
6-9
6.5.2 Battery replacement procedure
(1) Battery replacement procedure of the Battery holder unit

When the battery has been exhausted, replace the battery with a new one in
accordance with the procedure shown below.
POINTS
When replacing the battery, pay attention to the following.
(1) Back up the data using MT Developer before starting replacement.
(2) Firstly back up the data stored in the Motion CPU to the personal computer
which is installed MT Developer then replace the battery with a new one. After
setting the battery in the Battery holder unit, verify the backing up the data to
the personal computer which is installed MT Developer and the data in the
Motion CPU module, confirm the data is not changing.
In the following status, the backup time after power OFF is 3 minutes.
<Battery holder unit(Q170DBATC)>

Replacing Battery Battery(Q6BAT)
Battery connector for Q6BAT
Turn off the Multiple CPU system power

supply.
Lead wire
Remove the old battery from its holder.
Install a new battery into the holder in the

correct direction. Connect the lead
connector to the connector (BATTERY).
Turn on the Multiple CPU system power

supply.
END
6 - 10
(2) Q172DEX module battery replacement procedure

When the battery has been exhausted, replace the battery with a new one in
accordance with the procedure shown below.
POINT
When replacing the battery, pay attention to the following.
(1) The Multiple CPU power supply must be on for 10 minutes or longer before
dismounting the battery.
(2) Encoder data in the memory are backed up for a while by a capacitor even
after the battery is removed. However, since data in the memory may be
erased if the time for replacement exceeds the backup time shown the
following guaranteed value, replace the battery quickly.
• Backup time by capacitor : 3 minutes
Replacing Battery

supply for 10 minutes or longer.
Turn off the Multiple CPU system power

supply.
Side of the Q172DEX
Remove the encoder cable from Q172DEX.
Remove the Q172DEX from the base unit.
Remove the old battery from its holder of

the Q172DEX.
Front
LITHIUM BATTERY
MITSUBISHI
Install a new battery into the holder in the

correct direction. Connect the lead
connector to the connector (BATTERY).
Install the Q172DEX to the base unit. Encoder cable
Battery Connector
(A6BAT/MR-BAT) (BATTERY)
Connect the encoder cable to the
Q172DEX.

supply.
END
6 - 11
6.5.3 Resuming operation after storing the Motion controller
When the operation is to be resumed after being stored with the battery removed or
the battery has gone flat during storage, the contents of programs, parameters,
absolute position data and latch data cannot be guaranteed.
Before resuming operation, write the contents of programs, parameters, absolute
position data and latch data backed up prior to storage to SRAM built-in Motion CPU
module.
POINT
Before storing the Motion controller, always back up the contents of programs,
parameters, absolute position data and latch data to SRAM built-in Motion CPU
module.
6 - 12
6.6 Troubleshooting
This section describes the various types of trouble that occur when the system is
operated, and causes and corrective actions of these troubles.
6.6.1 Troubleshooting basics
The basic three points that must be followed in the troubleshooting are as follows.
(1) Visual inspection

Visually check the following.
(a) Movement of machine (stopped condition, operating condition)
(b) Power supply on/off
(c) Status of input/output devices
(d) Installation condition of the Power supply module, Motion CPU module, PLC
CPU module, I/O module, Q172DLX/Q172DEX/Q173DPX Motion module,
SSCNET cable, Synchronous encoder cable.
(e) State of wiring (I/O cables, cables)
(f) Display states of various types of indicators
PLC CPU module : MODE LED, RUN LED, ERR. LED, I/O LED, etc.
Motion CPU module : 7-segment LED (Installation mode, Operation mode,
Battery error, STOP/RUN, etc.)
(g) Status of setting of various types of switches (Setting of No. of stages of
extension base unit, power interrupt hold-on status).
After checking (a) to (g), monitor the operating conditions of servomotors and
error code using MT Developer and GX Developer.
(2) Check of trouble

Check to see how the operating condition varies while the Motion controller is
operated as follows.
(a) Set the RUN/STOP switch of Motion CPU module to STOP.
(b) Reset the trouble with the RUN/STOP/RESET switch of PLC CPU module.
(c) Turn ON and OFF the Multiple CPU system power supply.
(3) Narrowing down the range of trouble occurrence causes

Estimate the troubled part in accordance with items (1) and (2) above.
(a) Multiple CPU system or external devices
(b) Motion CPU or PLC CPU
(c) I/O module or others
(d) Servo program or Motion SFC program
(e) PLC program
6 - 13
6.6.2 Troubleshooting of Motion CPU module
This section describes the contents of troubles for the error codes and corrective
actions of the troubles.
As for troubleshooting of PLC CPU, refer to the QCPU User's Manual (Hardware
Design, Maintenance and Inspection) of their respective modules.
POINT
Check that the operating system software is installed before starting the Motion
CPU module.
(1) Troubleshooting flowchart

The followings show the contents of the troubles classified into a variety of
groups according to the types of events.
Error-occurrence description
(a)
"POWER" LED turns off
"Flowchart for when "POWER" LED turns off"
" ." does not flash in the first digit of (b)

7-segment LED "Flowchart for when " ." does not flash in the first digit of
7-segment LED"
(c)
"A00" displays on 7-segment LED
"Flowchart for when "A00" displays on 7-segment LED"
"AL" "L01" displays on 7-segment LED (d)

"Flowchart for when "AL" "L01" displays on 7-segment LED"
"AL" "A1" " " displays on 7-segment (e)

LED "Flowchart for when "AL" "A1" " " displays on 7-segment LED"
(f)
"BT " displays on 7-segment LED
"Flowchart for when "BT " displays on 7-segment LED"
(g)
" . . ." displays on 7-segment LED
"Flowchart for when " . . ." displays on 7-segment LED"
(h)
Servo amplifier does not start
"Flowchart for when servo amplifier does not start"
"AL" "S01" displays on 7-segment LED (i)

"Flowchart for when "AL" "S01" displays on 7-segment LED"
6 - 14
(a) Flowchart for when "POWER" LED turns off
The following shows the flowchart when "POWER" LED of the power
supply module turns off at the power supply ON or during operation.
"POWER" LED turns off
NO
Is there a power supply? Supply power.
YES
NO Does "POWER" YES

LED turn on?
Is the wiring/ NO Connect wiring and fix terminal

terminal connection
connection correctly.
correct?
YES
NO Does "POWER" YES

LED turn on?
Is the power NO
supply voltage within the The supply voltage should be within
rated range? the rated range.
YES
NO Does "POWER" YES

LED turn on?
Is the power supply NO

Fix the power supply module correctly.
module fixed?
YES
NO YES
Does "POWER"
LED turn on?
1) END
6 - 15
1)
Remove all modules other than the

power supply module from the base
unit.
NO The base unit that includes the

Does "POWER"
corresponding power module is faulty.
LED turn on?
(Replace it with a normal base unit.)
YES
Does "POWER" YES

LED turn on?
NO
Install all modules that removed from
the base unit to the base unit. H/W fault
Explain the error symptom and get
advice from out sales representative.
Check the sum of internal current

consumptions of the modules that
comprise the system.
Does the total

current exceed the rerated YES Reexamine the system configuration
output current of the power to make the total current less than the
supply module? rated output current of the power
supply module.
NO
NO Does "POWER" YES

LED turn on?
H/W fault
Check operation in the order starting
END
with the minimum system.
If the module will not work, explain
the error symptom and get advice
from out sales representative for the
modules with failure.
6 - 16
(b) Flowchart for when " ." does not flash in the first digit of
7-segment LED
" ." does not flash in the first digit of

7-segment LED.
Does "POWER" NO (a)

LED turn on? "Flowchart for when "POWER" LED
turns off"
YES
Is the
connecting direction
of extension cable correctly? NO
Connect the extension cable correctly.
(Isn't IN-IN or OUT-OUT
connection?)
YES
NO Does " . " flash YES
in the first digit of 7-segment
LED?
Is the "RESET"
RUN/STOP/RESETand
RUN/STOP switch of CPU Set the RUN/STOP/RESET and
No.1 and target CPU Module RUN/STOP switch to "STOP"
set to STOP?
"STOP"
NO Does " . " flash YES

in the first digit of 7-segment
LED?
H/W fault
Check operation in the order starting END
with the minimum system.
If the module will not work, explain
the error symptom and get advice
from out sales representative for the (Note) : Normally, " . " flashes in the first digit of
modules with failure. 7-segment LED.
6 - 17
(c) Flowchart for when "A00" displays on 7-segment LED
"A00" displays when the operating system software is not installed.

The following shows the flowchart when the "A00" displays at the power
supply ON or operation start.
"A00" displays on 7-segment LED
Is the
operating system NO
software installed to Motion
CPU module?
YES Install the operating system software.
Reset the Multiple CPU system.
Does "A00" disappear NO

on 7-segment LED?
YES
END Explain the error symptom and get

6 - 18
(d) Flowchart for when "AL" "L01" displays on 7-segment LED
""AL" (flashes 3 times) Steady "L01" display" displays at the system

setting error occurrence.
The following shows the flowchart when the ""AL" (flashes 3 times)
Steady "L01" display" displays during operation.
"AL" "L01" displays on 7-segment

LED.
Confirm details of error by Motion

CPU error batch monitor of
MT Developer.
Does a ROM ERROR YES

occur?
NO
NO
Is ROM operation executed?
YES
Set a rotary switch1 (SW1) to "0", a Set a rotary switch1 (SW1) to "0", a
rotary switch2 (SW2) to "6" of Motion rotary switch2 (SW2) to "0" of Motion
CPU module, and then execute ROM CPU module.
writing. (Mode operated by RAM)
YES Check that the installed modules

Does a LAY ERROR
correspond to system setting and
(SL**) occur?
correct details of error.
NO
Set by relative check of the system

setting not to occur a error, and
correct details of error.
Does "A00" "L01" NO

disappear on 7-segment
LED?
YES
END
6 - 19
(e) Flowchart for when "AL" "A1" " " displays on 7-segment
LED.
""AL" (flashes 3 times) Steady "A1" display " "" displays at the self-
diagnosis error occurrence.
Steady "L01" display " "" display" displays during operation.
: 4-digits error code is displayed in two sequential flashes of 2-digits each.
"AL" "L01" " " displays

on 7-segment LED.

MT Developer.
YES
Hardware cause fault?
NO
NO
Noise cause?
Correct each Multiple CPU system
setting based on the error causes .
YES
Take measures against noise.
Reset the Multiple CPU system. Explain the error symptom and get
Does "AL" "L01" NO

" " disappear on 7-segment
LED.
YES
END
6 - 20
(f) Flowchart for when "BT " displays on 7-segment LED
"BT1" or "BT1" displays when the external battery voltage of battery holder
unit is lowered.
"BT1" or "BT1" displays at the following cases.
• BT1: Battery voltage 2.7V or less
• BT2: Battery voltage 2.5V or less
The following shows the flowchart when the "BT " displays.
"BT " displays on 7-segment LED
Turn off the Multiple CPU system

power supply.
Replace the external battery.
Turn on the Multiple CPU system

power supply.
Does "BT "

disappear on 7-segment NO (SM58 or SM51 ON)
LED (Confirm ON/OFF by
monitoring SM )
YES (SM58, SM51 OFF)
END
H/W fault
REMARK
If SM51,SM58 turns on, the details of the programs, parameters, absolute position
data and latch data cannot be guaranteed.
6 - 21
(g) Flowchart for when " . . ." displays on 7-segment LED
" . . ." displays at the WDT error occurrence.

The following shows the flowchart when the " . . ." displays during
operation.
" . . ." displays on 7-segment LED

MT Developer.
Is the error NO
code of Motion CPU WDT
cause "1"?
YES
Is the error NO
code of Motion CPU WDT
Correct the main cycle not to exceed cause "2"?
1.0[s] by the following methods, and
write it to Motion CPU.
1) Change the operation cycle to
YES
large value in the system setting. Is the error NO
2) Reduce the number of execution to code of Motion CPU WDT
the event task program and NMI Correct the Motion operating time to cause "301"?
task program in the Motion SFC shorten by the following methods,
program. and write it to Motion CPU.
3) Reduce the number of execution to 1) Change the operation cycle to YES
the normal task program executed large value in the system setting.
simultaneously 2) Reduce the number of execution to Correct the servo program so that the
in the Motion SFC program. the event task program and NMI number of CPSTART instructions of
4) Reduce the number of automatic task program in the Motion SFC 8 or more points should not exceed
refresh points of CPU shared program. the number of simultaneous startable
memory. programs (14 or less), and write it to
Motion CPU.
Does " . . ." disappear NO

on 7-segment LED.
YES
END
6 - 22
(h) Flowchart for when servo amplifier does not start
The following shows the flowchart when servo amplifier does not start.
Servo amplifier does not start.
Is there error display NO

on 7-segment LED of Motion Remove the error cause.
CPU module?
YES NO YES
Does servo amplifier start?
NO Set the target axis in the system

Has the target axis set in
the system setting? setting.
YES
NO YES
Is the connection of NO
SSCNET cable correct? Connect the SSCNET cable correctly.
YES
NO YES
Is the axis select NO

switch of servo amplifier Set the axis select switch correctly.
correct?
YES
NO YES
Has the servo amplifier NO Remove the error cause of servo

connected from target axis near
amplifier that does not strat.
controller started?
YES
NO YES

END
6 - 23
(i) Flowchart for when "AL" "S01" displays on 7-segment LED
""AL" (flashes 3 times) Steady "S01" display" displays at the servo error
occurrence.
Steady "S01" display" displays during operation.
"AL" "S01" displays on 7-segment

LED.

MT Developer.
Remove the error cause of servo

amplifier, and then execute the servo
error reset (M3208+20n ON) or
re-turn on the servo amplifier power
supply.
Does "AL" "S01" NO

disappear on
7-segment LED?
YES
END
6 - 24
6.6.3 Confirming error code
The error code and error message can be read using MT Developer.
The procedure for reading error is as follows.
(1) Connect the PLC CPU module to personal computer (IBM PC/AT).
(2) Start MT Developer.
(3) Select [Online] - [Read from CPU] Menu of MT Developer, and read the project
data from Motion CPU.
(4) Start the monitor screen of MT Developer and select [Motion CPU error batch
monitor] menu.
(5) Confirm the error codes and error messages displayed on screen.
Refer to help of MT Developer for details of operating method.
6 - 25
6.6.4 I/O module troubleshooting
This section describes possible problems with I/O circuits and their corrective actions.
(1) Input circuit troubleshooting

The following describes possible problems with input circuits and their corrective
actions.
Input Circuit Troubleshooting and Corrective Action

Condition Cause Corrective action
• Leakage current of input switch • Connect an appropriate resistor which will
(e.g. drive by non-contact switch). make the voltage across the terminals of the
AC input input module lower than the OFF voltage
value.
Input signal
Example 1
Leakage AC input
is not Input module
current
turned
OFF. Input module
Power supply
It is recommended to use 0.1 to 0.47 [µF] + 47

to 120 [ ] (1/2W) for the CR constant.
• Drive by a limit switch with neon lamp. • Same as Example 1.
AC input • Provide an independent display circuit
Input signal
Example 2
separately.
is not
turned Leakage Input module
current
OFF.
Power supply
• Leakage current due to line capacity of wiring • Same as Example 1.
cable. (However, leakage current is not generated
(Line capacity C of twisted pair wire is approx. when the power supply is located in the input
Input signal 100 pF/m). equipment side as shown below.)
Example 3
is not AC input AC input

turned
OFF. Leakage
C Input module C Input module
current
Power supply Power supply

• Drive by switch with LED indicator. • Connect a register which will make the voltage
between the input module terminal and
common lower than the OFF voltage value, as
shown below.
DC input DC input
(plus common) (plus common)
Input signal
Example 4
is not
Leakage
turned current Resistor R
Input module Input module
OFF.
(Note-1) : A calculation example of a value for a

connected resistor is given on the
following page.
6 - 26
Input Circuit Troubleshooting and Corrective Action (Continued)

• Sneak path due to the use of two power • Use only one power supply.
supplies. • Connect a sneak path prevention diode.
Input signal (Figure below)
Example 5
is not
turned E1 E2 Input module
OFF. E1 E2 Input module
E1 >E2
Depending on response time setting, noise is Change the response time setting.
imported as input. Example : 1 [ms] 5[ms]
(When excessive noise is cyclic, shorter
response time setting may produce a higher
Example 6
False input effect.) When the above action does not have
due to an effect, take measures against noise to block
noise excessive noise, e.g. avoid tying the power
cables and control cables in a bundle, and add
surge absorbers to the noise sources such as
the relays and contactors used with the same
power supply.
<Calculation example of Example 4>

If a switch with LED display is connected to Q172DLX, and current of 4 [mA] is
leaked.
Q172DLX
Leakage
Motion CPU
current 4[mA]
module
3.6[k ]
24[VDC]
(a) Because the condition for OFF voltage (18[mA]) of Q172DLX is not
satisfied. Connect a resistor as shown below.
Q172DLX
4[mA]
Iz=0.18[mA]
IR=3.82[mA] Input impedance

5.6[k ]
3.6[k ]
24[VDC]
(b) Calculate the connecting resistor value R as indicated below.

To satisfy the 0.18 [mA] OFF current of the Q172DLX, the resistor R to be
connected may be the one where 3.82 [mA] or more will flow.
IR: IZ=Z(Input impedance): R
IZ 0.18 3
R Z(Input impedance)= 5.6 10 =264 [ ]
IR 3.82
R<264 [ ].
Assuming that resistor R is 220 [ ], the power capacity W of resistor R is:
2 2
W = (Input voltage) ÷ R = 26.4 ÷ 220 = 3.168 [W]
6 - 27
(c) The power capacity of the resistor selected is 3 to 5 times greater than the
actual current consumption. 220 [ ], 10 to 15 [W] resistor may therefore be
connected to the terminal in question.
(2) Output circuit troubleshooting

The following describes possible problems with output circuits and their
corrective actions.
Output Circuit Troubleshooting and Corrective Action

• When load is half-wave rectified • Connect a resistor of several ten k to
(This is typical some solenoids). several hundred k across the load.
Resistor
Output module D1 1)
Load
Load
Excessive
voltage is 2)
Example 1
applied to • When the polarity of the power supply is [1],

load when
the capacitor C is charged. When the
output turns
OFF polarity is [2], the voltage charged in C plus
the power supply voltage is applied to across
D1. The maximum value of the voltage is
approx. 2.2E. (This usage does not pose
problems to the output components but may
deteriorate the diode built in the load,
causing burnout, etc.) .
• Leakage current due to built-in surge • Connect a resistor across the load.
suppressor. (If the wiring from the output module to the
load is long, be careful since there may be a
Output module leakage current due to the line capacity.)
Example 2
Load
Load does
not turn OFF Resistor
Leakage current
(Triac output).
Load
6 - 28
APPENDICES
APPENDICES
APPENDIX 1 Cables
In this cable connection diagram, maker names of connectors are omitted. Refer to
"APPENDIX 2.7 Connector" for maker names of connectors.
APPENDIX 1.1 SSCNET cables
Generally use the SSCNET cables available as our products.
(1) Model explanation

Numeral in the column of cable length on the table is a symbol put in the " " part
of cable model. Cables of which symbol exists are available.
Cable length [m(ft.)] Application/
Cable model 0.15 0.3 0.5 1 3 5 10 20 30 40 50
Flex life remark
(0.49) (0.98) (1.64) (3.28) (9.84) (16.40) (32.81) (65.62) (98.43) (131.23) (164.04)
Standard code for

MR-J3BUSM 015 03 05 1 3 Standard
inside panel
Standard cable for
MR-J3BUSM-A 5 10 20 Standard
outside panel
Long distance
MR-J3BUSM-B (Note-1) 30 40 50 Long flex
cable
(Note-1) : For the cable of less than 30[m](98.43[ft.]), contact your nearest Mitsubishi sales representative.
(2) Specifications
Description
SSCNET cable model MR-J3BUS M MR-J3BUS M-A MR-J3BUS M-B
0.15 0.3 to 3 5 to 20 30 to 50
SSCNET cable length [m(ft.)]
Minimum bend radius

(0.49) (0.98 to 9.84) (16.40 to 65.62) (98.43 to 164.04)
Reinforcing coat cable: 50 (1.97) Reinforcing coat cable: 50 (1.97)
App.
25(0.98)
[mm(inch)] Code: 25 (0.98) Code : 30(1.18)
Tension strength [N] 70 140 420 (Enforced covering cord) 980 (Enforced covering cord)
Temperature range -40 to 80 -20 to 70

for use [°C(°F)] (Note-1) (-40 to 176) (-4 to 158)
Ambient Indoors (no direct sunlight), No solvent or oil
4.4 0.4
(0.09 0.008)
2.2 0.2
(0.09 0.003)
(0.17 0.016)
2.2 0.07
4.4 0.1
Optical cable
(0.09 0.003)
2.2 0.07
(0.17 0.004)
(Code)
External appearance
[mm(inch)]
2.2 0.07 4.4 0.1

(0.09 0.003) (0.17 0.004) 6 0.2
7.6 0.5
(0.24 0.008)
(0.30 0.02)
(Note-1): This temperature range for use is the value for optical cable (cord) only.
App - 1
APPENDICES
POINTS
(1) If the end face of code tip for the SSCNET cable is dirty, optical transmission
is interrupted and it may cause malfunctions. If it becomes dirty, wipe with a
(2) If the end face of code tip for SSCNET cable is dirty, optical transmission is
interrupted and it may cause malfunctions. If it becomes dirty, wipe with a
(3) When incinerating the SSCNET cable (optical fiber), hydrogen fluoride gas or
hydrogen chloride gas which is corrosive and harmful may be generated. For
disposal of the SSCNET cable (optical fiber), request for specialized
industrial waste disposal services who has incineration facility for disposing
hydrogen fluoride gas or hydrogen chloride gas.
(a) MR-J3BUS M
1) Model explanation
Type: MR-J3BUS M-
Symbol Cable type
None Standard code for inside panel
A Standard cable for outside panel
B Long distance cable
Symbol Cable length [m(ft.)]

015 0.15(0.49)
03 0.3(0.98)
05 0.5(1.64)
1 1(3.28)
3 3(9.84)
5 5(16.40)
10 10(32.81)
20 20(65.62)
30 30(98.43)
40 40(131.23)
50 50(164.04)
2) Exterior dimensions
• MR-J3BUS015M
[Unit: mm(inch)]
15 13.4 37.65
6.7(0.26) (0.59) (0.53) (1.48)
Protective tube
20.9(0.82)
150 +50
-0
(5.91)
(0.31)
8+0
2.3(0.09)
1.7(0.07)
App - 2
APPENDICES
• MR-J3BUS03M to MR-J3BUS3M
[Unit: mm(inch)]
Refer to the table of this section (1) for cable length (L).
Protective tube (Note)
100 100
(3.94) L (3.94)
(Note) : Dimension of connector part is the same as that of MR-J3BUS015M.
• MR-J3BUS5M-A to MR-J3BUS20M-A,MR-J3BUS30M-B to
MR-J3BUS50M-B
Refer to the table of this section (1) for cable length (L).
Variation [mm(inch)]
SSCNET cable
A B
MR-J3BUS5M-A to MR-J3BUS20M-A 100(3.94) 30(1.18)
MR-J3BUS30M-B to MR-J3BUS50M-B 150(5.91) 50(1.97)
[Unit: mm(inch)]
Protective tube
(Note)
(A) (B) (B) (A)

L
(Note) : Dimension of connector part is the same as that of MR-J3BUS015M.
POINTS
Keep the cap and the tube for protecting light code end of SSCNET cable in a
plastic bag with a zipper of SSCNET cable to prevent them from becoming dirty.
App - 3
APPENDICES
APPENDIX 1.2 Serial absolute synchronous encoder cable
Generally use the serial absolute synchronous encoder cables available as our
products. If the required length is not found in our products, fabricate the cable on the
customer side.
(1) Selection
The following table indicates the serial absolute synchronous encoder cables
used with the serial absolute synchronous encoder.
Connector sets (Q170ENCCNS) are also available for your fabrication.
Table 1 Wire models
Type Length [m(ft.)] Wire model
2(6.56), 5(16.40), 10(32.81), 20(65.62),
Q170ENCCBLM M14B0023 12 pair (BLACK)
30(98.43), 50(164.04)
Use the following or equivalent twisted pair cables as the serial absolute
synchronous encoder cables.
Table 2 Connector sets
Connector sets type Description
• Connector shell kits

Q170ENCCNS
• Plug cable clump
Table 3 Wire specifications

Characteristics of one core
Core Finished
Number of Structure Conductor Insulating OD
Wire model size sheath OD
2 cores [Number of resistance [mm]
[mm ] d[mm]
wires/mm] [ /km] (Note-2)
(Note-1)
M14B0023 12 pair (BLACK) 0.2 24(12 pair) 40/0.08 105 or less 0.88 11.0
(Note-1): "d" is as shown below.

d
Insulation sheath
Conductor
(Note-2): Standard OD (Outside Diameter). Maximum OD is about 10% larger.
! CAUTION
When fabricating the encoder cable, do not make incorrect connection. Wrong connection will
cause runaway or explosion.
App - 4
APPENDICES
(2) Q170ENCCBL M
(a) Model explanation
Type: Q170ENCCBL M

2 2(6.56)
5 5(16.40)
10 10(32.81)
20 20(65.62)
30 30(98.43)
50 50(164.04)
(b) Connection diagram

When fabricating a cable, use the recommended wire and connector set
Q170ENCCNS for encoder cable given on APPENDIX 1.2, and make the
cable as show in the following connection diagram. Maximum cable length
is 50m(164.04ft.).
SY.ENC connector
Q172DEX
1 11 Encoder connector
Encoder connector
LG 2 LG 12 Synchronous Pin Signal Pin Signal
LG LG encoder cable Q170ENC A K MR
3 13
LG 4 14
L M A
B L MRR
TREN.
5 TREN 15 COM
C M
SY.ENC K U N B
6 16 Synchro- D N SHD
7 MD 17 MDR 1 or 2 nous J T V P C E BAT P
8 18 encoder H S R D F R LG
MR MRR
9 19 P5 G F E G S P5
BAT 10 P5 20 H MD T
50m(164.04ft.) or less J
P5 P5 MDR
Q172DEX side Encoder side

10120-3000PE(connector) MS3106B22-14S(plug)
10320-52F0-008(connector case) MS3057-12A(cable clump)
P5 19 S
LG 11 R
P5 20
LG 12
P5 18
LG 2
BAT 9 E
LG 1
MR 7 K
MRR 17 L
MD 6 H
MDR 16 J
SD plate N
:Twisted pair cable
Cable length 50m(164.04[ft.]) or less
App - 5
APPENDICES
APPENDIX 1.3 Battery cable
Generally use the battery cable available as our products. If the required length is not
found in our products, fabricate the cable on the customer side. Make the battery cable
within 0.5m(1.64ft.).
(1) Q170DBATCBL M
Type : Q170DBATCBL M

05 0.5(1.64)

CPU Module side Battery holder side
4 1
1 3
50351-8100 (Terminal) 1376476-1 (Terminal)

51103-0400 (Connector) 1376477-3 (Connector)
+ 4 1 +
2 N.C.
- 3 3 -
N.C. 2
FG 1
: Twisted pair cable

(Note) : Use a cable of wire size AWG24.
App - 6
APPENDICES
APPENDIX 1.4 Forced stop input cable
Generally use the forced stop input cable available as our products. If the required
length is not found in our products, fabricate the cable on the customer side. Make the
forced stop input cable within 30m(98.43ft.).
(1) Q170DEMICBL M
Type : Q170DEMICBL M

05 0.5(1.64)
1 1(3.28)
3 3(9.84)
5 5(16.40)
10 10(32.81)
15 15(49.21)
20 20(65.62)
25 25(82.02)
30 30(98.43)

CPU module side Solderless terminal
2
1
5556TL (Terminal)
5557-02R (Connector)
EMI.COM 2 EMI.COM
EMI 1 EMI
: Twisted pair cable

(Note) : Use a cable of wire size AWG24.
App - 7
APPENDICES
APPENDIX 2 Exterior Dimensions
APPENDIX 2.1 CPU module
(1) Q172DCPU Module

[Unit: mm (inch)]
Q172DCPU
F01 F01
SW
AB E
CDE
23 6
23 6
CD
45
45
AB
1 2
789 789
STOP RUN
CAUTION
EMI
98(3.86)
CN1
FRONT
BAT
119.3(4.70) 27.4(1.08)
(2) Q173DCPU Module

[Unit: mm (inch)]
Q173DCPU
F01 F01
SW
AB E
CDE
23 6
23 6
CD
45
45
AB
1 2
789 789
STOP RUN
CAUTION
EMI
98(3.86)
CN1
CN2
FRONT
BAT
119.3(4.70) 27.4(1.08)
App - 8
APPENDICES
APPENDIX 2.2 Servo external signals interface module (Q172DLX)
[Unit: mm (inch)]
Q172DLX
98(3.86)
CTRL
Q172DLX
90(3.54) 45(1.77) 27.4(1.08)
APPENDIX 2.3 Synchronous encoder interface module (Q172DEX)
[Unit: mm (inch)]
Q172DEX
SY.ENC TREN
1 1
2 2
SY.ENC1
98(3.86)
LITHIUM BATTERY
MITSUBISHI
SY.ENC2
Q172DEX
4.2(0.17)
90(3.54) 39(1.54) 27.4(1.08)
App - 9
APPENDICES
APPENDIX 2.4 Manual pulse generator interface module (Q173DPX)
[Unit: mm (inch)]
Q173DPX
PLS.A PLS.B TREN
1 1 1
2 2 2
3 3 3
98(3.86)
PULSER
ON
1 2 3 4 5 6
KSD06S
Q173DPX
90(3.54) 45(1.77) 27.4(1.08)
App - 10
APPENDICES
APPENDIX 2.5 Power supply module (Q61P-A1, Q61P-A2, Q61P, Q62P, Q63P, Q64P)
[Unit: mm (inch)]
(1) Q61P-A1, Q61P-A2, Q61P, Q62P, Q63P
Q61P
POWER
98(3.86)
PULL
90(3.54) 55.2(2.17)
(2) Q64P
[Unit: mm (inch)]
Q64P
POWER
98(3.86)
PULL
115(4.53) 55.2(2.17)
App - 11
APPENDICES
APPENDIX 2.6 Battery holder unit (Q170DBATC)
(1) Battery holder unit (Q170DBATC)

[Unit: mm (inch)]
2- 5.3(0.21)
(Fixing screw M5 14)
BATTERY
CPU
45(1.77)
60(2.36)
(0.30)
40(1.57)
7.5
80(3.15)
18.4(0.72)
30(1.18)
(0.46)
11.6
App - 12
APPENDICES
APPENDIX 2.7 Connector
(1) Cable connector for serial absolute synchronous encoder

(Sumitomo 3M make (MDR type))
Type
Number of pins Type
Connector Connector case
Solder connection type
10120-3000PE 10320-52F0-008
(Quick release metal latch type)
Solder connection type
20 10120-3000PE 10320-52A0-008
(Threaded type)
Insulation displacement type
10120-6000EL(Note) 10320-3210-000(Note)
(Quick release metal latch type)
(Note): These connectors are not options. Please purchase them by customer.
(a) Solder connection type(Quick release metal latch type)

Type Connector : 10120-3000PE
Connector case: 10320-52F0-008
[Unit: mm (inch)]
12.0(0.47)
10.0(0.39)
22.0 14.0
(0.87) (0.55)
39.0(1.54)
23.8(0.94)
33.3 12.7
(1.31) (0.50)
(b) Solder connection type(Threaded type)

Type Connector : 10120-3000PE
Connector case: 10320-52A0-008
[Unit: mm (inch)]
12.0(0.47)
10.0(0.39)
27.4(1.08)
22.0(0.87) 14.0(0.55)
39.0(1.54)
23.8(0.94)
33.3(1.31) 12.7
(0.22)
5.7
(0.50)
App - 13
APPENDICES
(c) Insulation displacement type(Quick release metal latch type)

Type Connector : 10120-6000EL
Connector case: 10320-3210-000
[Unit: mm (inch)]
11.5(0.45)
6.7
20.9 Position where e.g. logo is indicated

2- 0.5(0.02)
42.0(1.65)
33.0(1.30)
29.7(1.17)
(2) SSCNET cable connector
4.8(0.19)
(0.53)
13.4
1.7
(0.07)
(0.59)
15
2.3
9.3(0.37)
(0.26)
(0.09)
6.7
17.6 0.2 8
(0.69 0.01) (0.31)
20.9 0.2
(0.82 0.01)
App - 14
APPENDICES
(3) Battery cable connector

(a) Battery holder side (Tyco Electronics AMP K.K make)
Type Connector : 1376477-3
Terminal : 1376476-1
[Unit: mm (inch)]
6.5 (0.26)
(0.21)
5.4
8.2 (0.32) 8.3 (0.33)

10.0 (0.39)
(b) CPU module side (Molex Incorporated make)

Type Connector : 51103-0400
Terminal : 50351-8100
[Unit: mm (inch)]
12.2 (0.48) 7.5 (0.30) 9.5 (0.37)
(0.23)
5.8
10.5 (0.41)
(4) Forced stop input connector (Molex Incorporated make)

Type Connector : 5557-02R-210
Terminal : 5556TLPBTL
[Unit: mm (inch)]
5.4 10.6
(0.21) (0.42)
(0.42)
10.7
(0.33)
19.6 (0.77)
8.5
(0.25)
6.3
3.5
(0.14)
(0.38)
9.6
App - 15
APPENDICES
APPENDIX 2.8 Manual pulse generator (MR-HDP01)
[Unit: mm (inch)]
3.6(0.14) Packing t =2.0

3 Studs (M4 10)
PCD72, equi-spaced
0 90
10
NP
50(1.97)
70(2.76)
80(3.15) 1
60(2.36) 0.5
20
80
5 to
12V 0V A B
30
70
60
40
50
M3 6
16 20 27.0 0.5 8.89 7.6

3- 4.8(0.19) (0.63)(0.79) (1.06) (0.35) (0.30)
equi-spaced
Space
) 2
-0
44
(2.
72(2.8
3)
62
0.2
The figure of processing a disc
APPENDIX 2.9 Serial absolute synchronous encoder (Q170ENC)
[Unit: mm (inch)]
84(3.31) 58.5(2.30)
70.7(2.78) 28(1.10) 30(1.18)
45
7(0.28) 2(0.08)
40(1.57)
14(0.55)
8.72(0.34)
9.52(0.37)
75(2.95)
A
70.7(2.78)
(0.34)
8.72
122.5(4.82)
A' Cross-section diagram AA'

58(2.28)
4- 5.5(0.22)
22.5(0.89)
40(1.57) 36.5(1.44)
App - 16
APPENDICES
MEMO
App - 17
WARRANTY
Please confirm the following product warranty details before using this product.
1. Gratis Warranty Term and Gratis Warranty Range

If any faults or defects (hereinafter "Failure") found to be the responsibility of Mitsubishi occurs during use of the
product within the gratis warranty term, the product shall be repaired at no cost via the sales representative or
Mitsubishi Service Company.
However, if repairs are required onsite at domestic or overseas location, expenses to send an engineer will be solely
at the customer's discretion. Mitsubishi shall not be held responsible for any re-commissioning, maintenance, or
testing on-site that involves replacement of the failed module.
[Gratis Warranty Term]

Note that an installation period of less than one year after installation in your company or your customer’s premises
or a period of less than 18 months (counted from the date of production) after shipment from our company,
whichever is shorter, is selected.
[Gratis Warranty Range]

(1) Diagnosis of failure
As a general rule, diagnosis of failure is done on site by the customer.
However, Mitsubishi or Mitsubishi service network can perform this service for an agreed upon fee upon the
customer’s request.
There will be no charges if the cause of the breakdown is found to be the fault of Mitsubishi.
(2) Breakdown repairs

There will be a charge for breakdown repairs, exchange replacements and on site visits for the following four
conditions, otherwise there will be a charge.
1) Breakdowns due to improper storage, handling, careless accident, software or hardware design by the
customer
2) Breakdowns due to modifications of the product without the consent of the manufacturer
3) Breakdowns resulting from using the product outside the specified specifications of the product
4) Breakdowns that are outside the terms of warranty
Since the above services are limited to Japan, diagnosis of failures, etc. are not performed abroad.
If you desire the after service abroad, please register with Mitsubishi. For details, consult us in advance.
2. Exclusion of Loss in Opportunity and Secondary Loss from Warranty Liability

Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; opportunity
loss or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products other than Mitsubishi products; and to
other duties.
3. Onerous Repair Term after Discontinuation of Production

Mitsubishi shall accept onerous product repairs for seven years after production of the product is discontinued.
4. Delivery Term
In regard to the standard product, Mitsubishi shall deliver the standard product without application settings or
adjustments to the customer and Mitsubishi is not liable for on site adjustment or test run of the product.
5. Precautions for Choosing the Products

(1) These products have been manufactured as a general-purpose part for general industries, and have not been
designed or manufactured to be incorporated in a device or system used in purposes related to human life.
(2) Before using the products for special purposes such as nuclear power, electric power, aerospace, medicine,
passenger movement vehicles or under water relays, contact Mitsubishi.
(3) These products have been manufactured under strict quality control. However, when installing the product where
major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the
system.
(4) When exporting any of the products or related technologies described in this catalogue, you must obtain an
export license if it is subject to Japanese Export Control Law.
MOTION CONTROLLER Qseries
User's Manual (Q173DCPU/Q172DCPU)
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
MODEL Q173D-U-E
MODEL 1XB927
CODE
When exported from Japan, this manual does not require application to the
IB(NA)-0300133-A(0801)MEE Ministry of Economy, Trade and Industry for service transaction permission.
IB(NA)-0300133-A(0801)MEE Specifications subject to change without notice.

MITSUBISHI ELECTRIC
HEADQUARTERS EUROPEAN REPRESENTATIVES EUROPEAN REPRESENTATIVES EURASIAN REPRESENTATIVES

MITSUBISHI ELECTRIC EUROPE B.V. EUROPE GEVA AUSTRIA ALFATRADE Ltd. MALTA Kazpromautomatics Ltd. KAZAKHSTAN
German Branch Wiener Straße 89 99, Paola Hill Mustafina Str. 7/2
Gothaer Straße 8 AT-2500 Baden Malta- Paola PLA 1702 KAZ-470046 Karaganda
D-40880 Ratingen Phone: +43 (0)2252 / 85 55 20 Phone: +356 (0)21 / 697 816 Phone: +7 7212 / 50 11 50
Phone: +49 (0)2102 / 486-0 Fax: +43 (0)2252 / 488 60 Fax: +356 (0)21 / 697 817 Fax: +7 7212 / 50 11 50
Fax: +49 (0)2102 / 486-1120 TEHNIKON BELARUS INTEHSIS srl MOLDOVA
MITSUBISHI ELECTRIC EUROPE B.V. CZECH REPUBLIC Oktyabrskaya 16/5, Off. 703-711 bld. Traian 23/1
Czech Branch BY-220030 Minsk MD-2060 Kishinev
Avenir Business Park, Radlická 714/113a Phone: +375 (0)17 / 210 46 26 Phone: +373 (0)22 / 66 4242 MIDDLE EAST REPRESENTATIVES
CZ-158 00 Praha 5 Fax: +375 (0)17 / 210 46 26 Fax: +373 (0)22 / 66 4280
Phone: +420 (0)251 551 470 ILAN & GAVISH Ltd. ISRAEL
Koning & Hartman b.v. BELGIUM Koning & Hartman b.v. NETHERLANDS 24 Shenkar St., Kiryat Arie
Fax: +420 (0)251-551-471 Woluwelaan 31 Haarlerbergweg 21-23 IL-49001 Petah-Tiqva
MITSUBISHI ELECTRIC EUROPE B.V. FRANCE BE-1800 Vilvoorde NL-1101 CH Amsterdam Phone: +972 (0)3 / 922 18 24
French Branch Phone: +32 (0)2 / 257 02 40 Phone: +31 (0)20 / 587 76 00 Fax: +972 (0)3 / 924 0761
25, Boulevard des Bouvets Fax: +32 (0)2 / 257 02 49 Fax: +31 (0)20 / 587 76 05
F-92741 Nanterre Cedex TEXEL ELECTRONICS Ltd. ISRAEL
INEA BH d.o.o. BOSNIA AND HERZEGOVINA Beijer Electronics AS NORWAY 2 Ha´umanut, P.O.B. 6272
Phone: +33 (0)1 / 55 68 55 68 Aleja Lipa 56 Postboks 487
Fax: +33 (0)1 / 55 68 57 57 IL-42160 Netanya
BA-71000 Sarajevo NO-3002 Drammen Phone: +972 (0)9 / 863 39 80
MITSUBISHI ELECTRIC EUROPE B.V. IRELAND Phone: +387 (0)33 / 921 164 Phone: +47 (0)32 / 24 30 00 Fax: +972 (0)9 / 885 24 30
Irish Branch Fax: +387 (0)33/ 524 539 Fax: +47 (0)32 / 84 85 77
Westgate Business Park, Ballymount CEG INTERNATIONAL LEBANON
AKHNATON BULGARIA MPL Technology Sp. z o.o. POLAND Cebaco Center/Block A Autostrade DORA
IRL-Dublin 24 4 Andrej Ljapchev Blvd. Pb 21 Ul. Krakowska 50
Phone: +353 (0)1 4198800 Lebanon - Beirut
BG-1756 Sofia PL-32-083 Balice Phone: +961 (0)1 / 240 430
Fax: +353 (0)1 4198890 Phone: +359 (0)2 / 817 6004 Phone: +48 (0)12 / 630 47 00 Fax: +961 (0)1 / 240 438
MITSUBISHI ELECTRIC EUROPE B.V. ITALY Fax: +359 (0)2 / 97 44 06 1 Fax: +48 (0)12 / 630 47 01
Italian Branch INEA CR d.o.o. CROATIA Sirius Trading & Services srl ROMANIA
Viale Colleoni 7 Losinjska 4 a Aleea Lacul Morii Nr. 3
I-20041 Agrate Brianza (MI) HR-10000 Zagreb RO-060841 Bucuresti, Sector 6
Phone: +39 039 / 60 53 1 AFRICAN REPRESENTATIVE
Phone: +385 (0)1 / 36 940 - 01/ -02/ -03 Phone: +40 (0)21 / 430 40 06
Fax: +39 039 / 60 53 312 Fax: +385 (0)1 / 36 940 - 03 Fax: +40 (0)21 / 430 40 02 CBI Ltd. SOUTH AFRICA
MITSUBISHI ELECTRIC EUROPE B.V. SPAIN AutoCont C.S. s.r.o. CZECH REPUBLIC Craft Con. & Engineering d.o.o. SERBIA Private Bag 2016
Spanish Branch Technologická 374/6 Bulevar Svetog Cara Konstantina 80-86 ZA-1600 Isando
Carretera de Rubí 76-80 CZ-708 00 Ostrava-Pustkovec SER-18106 Nis Phone: + 27 (0)11 / 928 2000
E-08190 Sant Cugat del Vallés (Barcelona) Phone: +420 595 691 150 Phone:+381 (0)18 / 292-24-4/5 Fax: + 27 (0)11 / 392 2354
Phone: 902 131121 // +34 935653131 Fax: +420 595 691 199 Fax: +381 (0)18 / 292-24-4/5
Fax: +34 935891579
B:TECH A.S. CZECH REPUBLIC INEA SR d.o.o. SERBIA
MITSUBISHI ELECTRIC EUROPE B.V. UK U Borové 69 Izletnicka 10
UK Branch CZ-58001 Havlíčkův Brod SER-113000 Smederevo
Travellers Lane Phone: +420 (0)569 777 777 Phone: +381 (0)26 / 617 163
UK-Hatfield, Herts. AL10 8XB Fax: +420 (0)569-777 778 Fax: +381 (0)26 / 617 163
Phone: +44 (0)1707 / 27 61 00
Fax: +44 (0)1707 / 27 86 95 Beijer Electronics A/S DENMARK AutoCont Control s.r.o. SLOVAKIA
Lykkegårdsvej 17, 1. Radlinského 47
MITSUBISHI ELECTRIC CORPORATION JAPAN DK-4000 Roskilde SK-02601 Dolny Kubin
Office Tower “Z” 14 F Phone: +45 (0)46/ 75 76 66 Phone: +421 (0)43 / 5868210
8-12,1 chome, Harumi Chuo-Ku Fax: +45 (0)46 / 75 56 26 Fax: +421 (0)43 / 5868210
Tokyo 104-6212
Phone: +81 3 622 160 60 Beijer Electronics Eesti OÜ ESTONIA CS MTrade Slovensko, s.r.o. SLOVAKIA
Fax: +81 3 622 160 75 Pärnu mnt.160i Vajanskeho 58
EE-11317 Tallinn SK-92101 Piestany
MITSUBISHI ELECTRIC AUTOMATION, Inc. USA Phone: +372 (0)6 / 51 81 40 Phone: +421 (0)33 / 7742 760
500 Corporate Woods Parkway Fax: +372 (0)6 / 51 81 49 Fax: +421 (0)33 / 7735 144
Vernon Hills, IL 60061
Phone: +1 847 478 21 00 Beijer Electronics OY FINLAND INEA d.o.o. SLOVENIA
Fax: +1 847 478 22 53 Jaakonkatu 2 Stegne 11
FIN-01620 Vantaa SI-1000 Ljubljana
Phone: +358 (0)207 / 463 500 Phone: +386 (0)1 / 513 8100
Fax: +358 (0)207 / 463 501 Fax: +386 (0)1 / 513 8170
UTECO A.B.E.E. GREECE Beijer Electronics AB SWEDEN
5, Mavrogenous Str. Box 426
GR-18542 Piraeus SE-20124 Malmö
Phone: +30 211 / 1206 900 Phone: +46 (0)40 / 35 86 00
Fax: +30 211 / 1206 999 Fax: +46 (0)40 / 35 86 02
MELTRADE Ltd. HUNGARY Econotec AG SWITZERLAND
Fertő utca 14. Hinterdorfstr. 12
HU-1107 Budapest CH-8309 Nürensdorf
Phone: +36 (0)1 / 431-9726 Phone: +41 (0)44 / 838 48 11
Fax: +36 (0)1 / 431-9727 Fax: +41 (0)44 / 838 48 12
Beijer Electronics SIA LATVIA GTS TURKEY
Vestienas iela 2 Darülaceze Cad. No. 43 KAT. 2
LV-1035 Riga TR-34384 Okmeydanı-Istanbul
Phone: +371 (0)784 / 2280 Phone: +90 (0)212 / 320 1640
Fax: +371 (0)784 / 2281 Fax: +90 (0)212 / 320 1649
Beijer Electronics UAB LITHUANIA CSC Automation Ltd. UKRAINE
Savanoriu Pr. 187 4-B, M. Raskovoyi St.
LT-02300 Vilnius UA-02660 Kiev
Phone: +370 (0)5 / 232 3101 Phone: +380 (0)44 / 494 33 55
Fax: +370 (0)5 / 232 2980 Fax: +380 (0)44 / 494-33-66
MITSUBISHI
ELECTRIC Mitsubishi Electric Europe B.V. /// FA - European Business Group /// Gothaer Straße 8 /// D-40880 Ratingen /// Germany
FACTORY AUTOMATION Tel.: +49(0)2102-4860 /// Fax: +49(0)2102-4861120 /// [email protected] /// www.mitsubishi-automation.com

q172 & q173dcpu manual

Uploaded by

Copyright:

Available Formats

q172 & q173dcpu manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

q172 & q173dcpu manual

Uploaded by

Copyright:

Available Formats

MITSUBISHI ELECTRIC

Indicates that incorrect handling may cause hazardous

Indicates that incorrect handling may cause hazardous

Depending on circumstances, procedures indicated by CAUTION may also be linked to serious

2. For fire prevention

(2) Parameter settings and programming

(3) Transportation and installation

(5) Trial operation and adjustment

(8) Maintenance, inspection and part replacement

(9) About processing of waste

(10) General cautions

Japanese Manual Number IB(NA)-0300125

© 2008 MITSUBISHI ELECTRIC CORPORATION

Thank you for choosing the Mitsubishi Motion controller Q173DCPU/Q172DCPU.

Safety Precautions .........................................................................................................................................A- 1

2. SYSTEM CONFIGURATION 2- 1 to 2-72

2.1 Motion System Configuration .................................................................................................................. 2- 1

3.1 System Designing Procedure .................................................................................................................. 3- 1

4.1 Module Installation ................................................................................................................................... 4- 1

5. TRIAL OPERATION AND ADJUSTMENT 5- 1 to 5- 8

5.1 Checklist before Trial Operation .............................................................................................................. 5- 1

6. INSPECTION AND MAINTENANCE 6- 1 to 6-28

6.1 Maintenance Works ................................................................................................................................. 6- 2

APPENDICES App- 1 to App-17

The following manuals are also related to this product.

(1) Motion controller

Q173DCPU/Q172DCPU Motion controller (SV13/SV22) Programming Manual (Motion SFC)

Q173DCPU/Q172DCPU Motion controller (SV13/SV22) Programming Manual (REAL MODE)

Q173DCPU/Q172DCPU Motion controller (SV22) Programming Manual (VIRTUAL MODE)

QCPU User's Manual (Function Explanation, Program Fundamentals)

QCPU User's Manual (Multiple CPU System)

QCPU (Q Mode)/QnACPU Programming Manual (Common Instructions)

QCPU (Q Mode)/QnACPU Programming Manual (PID Control Instructions)

QCPU (Q Mode)/QnACPU Programming Manual (SFC)

I/O Module Type Building Block User's Manual

(3) Servo amplifier

Item Reference Manual

1.2 Differences between Q173DCPU/Q172DCPU and Q173HCPU/Q172HCPU

Items Q173DCPU Q172DCPU Q173HCPU Q173HCPU

2.1 Motion System Configuration

Power supply module/

Power supply module/

Battery SSCNET cable

It is possible to select the best according to the system.

(2) Peripheral device configuration for the Q173DCPU/Q172DCPU

(a) USB configuration (b) RS-232 configuration

PLC CPU module PLC CPU module

RS-232 communication cable

MIT SUBISHI MIT SUBISHI

Personal computer Personal computer

2.1.1 Q173DCPU System overall configuration

Motion CPU control module

Manual pulse generator 3/module

Serial absolute synchronous encoder cable

Battery holder unit

Input/output (Up to 256 points)

Interrupt signals (16 points)

Extension base unit EMI forced stop input (24VDC)

(MR-J3BUS M(-A/-B)) SSCNET (CN1)

MR-J3- B model Servo amplifier,