Scribd
Upload
9 views3 pages

2q Reviwer in TD

Uploaded by

echalicocolleenmei
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
9 views3 pages

2q Reviwer in TD

Uploaded by

echalicocolleenmei
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Reviewer in TD1

Second Quarter
Compass is used to draw an arc
and circle
1st step Draw the given line AB,
arc AB and angle AOB on the
drawing paper.
First step, given line AB and
4th step Given arc AB, using the
point P where the perpendicular
ends of arc as centers, draw two
line should pass, draw an arc
arcs with the same radius which
with point P as center. The arc
will intersect at point C and D.
intersects in Line AB at point
2nd step Given line AB, using C and D
points A and B as centers, draw
Second step, with point C and D
two arcs with the same radius
as centers, draw two arcs
which will intersect at point C and
having the same radius. These
D.
two arcs will intersect in Point
E
Last step, the points that
needed to be connected with a
straight line are Points P and E
First step, given the line AB and
Line PE is the line that is
point P where the perpendicular
perpendicular to line AB?
line should pass. The first step in
constructing a perpendicular line
through the given line is Use
point P as center, draw an arc
that will intersect line AB at
point C and point D.
Second step, using points C and
D as centers, the lines will be
drawn and intersect at point E is Given Line OA, the 45-degrees
Arcs having the same radius angle should pass in Point O
In the last step, the points that In order to draw an arc that will
needed to be connected with a intersect Line BA at point C and
straight line is Point P and D, Point O will be used as
point E center?
Line PE is the line that is Compass will be used to draw
perpendicular to line AB and the arc CD and arc FG?
passes through point P?
Using Point C and Point D as
centers, Arcs with same
radius will be drawn that will
intersect at Point E?

LRMD Page 1 of 3
SS
which equidistant from the
center.
Connect Point E and Point O
with Light straight line
Line EO is a perpendicular Diameter is the straight
bisector of Line BA. line that is drawn through
the center of the Circle
Line BA is a perpendicular meeting the circumference
bisector of Line EO. at both ends.
Angle EOA is 90 degrees Circumference the
Angle HOA is 45 degrees distance around the circle.

Using Point F and Point G as Radius is the straight line


centers, Arcs with same that is drawn from the
radius will be drawn that center to the
will intersect at Point. circumference.

The last step in Drawing 45 Arc is drawn in any part of


degrees on a given line is the circumference.
Bisect angle EOA, Chord is the any straight
following the procedure line that is drawn across the
in bisecting angle circle meeting the
circumference at both ends.
Tangent the straight line
which touches the
circumference in only one
point even if the line is
extended to any direction?
Line AB should be equally
divided into 10. Segment is a part of a
circle bounded by an arc
and a chord.
In the given figure above,
Sector is a part of a circle
Line BC is drawn at any
bounded by two radii and
angle.
an arc.
The 2nd step in Dividing a
Quadrant is a part of a
line into a number of
circle bounded by two radii
divisions is Step-off on
at right angles and an arc.
line AC the required
number of divisions What is the 1st step in
inscribing a square in a
Line AB is divided into 10.
circle is to Draw two
In order to draw parallel diameters which will
lines, you will be used 45 ͦ x be perpendicular to
45 ͦ x 90 ͦ triangle and 30 ͦ each other
x 60 ͦ x 90 ͦ triangle.
If the square desired is to
Circle is a figure that has have sides at 45 degrees
closed curve, all points to the horizontal line, the

LRMD Page 2 of 3
SS
positions of the
diameters should be
Vertical and Horizontal
in position.
If the sides of square are
vertical and horizontal, the
diameter should be positioned
45 degrees to the horizontal

The 2nd step in Inscribing a


square in a circle Connect
the ends of the diameter
to form a square
Inscribe means to draw
polygon inside the circle
Circumscribe means To draw
polygon outside the circle
The 1st step in drawing a
rhombus on a given size of
side is to Draw a horizontal
line AB equal to the given
size of side.
Line AB can also be drawn in
Vertical line
The 2nd step in drawing a
rhombus on a given size of
side is Using points A and
B as centers and distance
AB as radius draw arcs
above and below the line
AB which will intersect at
point C and D.
The last step in
drawing a rhombus on
a given size of side is
Connect point A to
C, C to B, B to D and
D to A.

LRMD Page 3 of 3
SS

You might also like