Circuit Theory

Chapter 4
Circuit Theorems

Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

1
Circuit Theorems - Chapter 4

4.1 Motivation
4.2 Linearity Property
4.3 Superposition
4.4 Source Transformation
4.5 Thevenin’s Theorem
4.6 Norton’s Theorem
4.7 Maximum Power Transfer
2
 4.1 Motivation (1)
If you are given the following circuit, are
there any other alternative(s) to determine
the voltage across 2W resistor?

What are they? And how?

Can you work it out by inspection? 3
 4.2 Linearity Property (1)
It is the property of an element describing a linear relationship
between cause and effect.
A linear circuit is one whose output is linearly related (or
directly proportional) to its input.

Homogeneity (scaling) property

v=iR → kv=kiR

Additive property

v1 = i1 R and v2 = i2 R
→ v = (i1 + i2) R = v1 + v2 4
 4.2 Linearity Property (2)
Example 1
By assume Io = 1 A, use linearity to find the actual value of Io in the
circuit shown below.

*Refer to in-class illustration, text book, answer Io = 3A 5

4.3 Superposition Theorem (1)
It states that the voltage across (or current
through) an element in a linear circuit is the
algebraic sum of the voltage across (or currents
through) that element due to EACH independent
source acting alone.

The principle of superposition helps us to analyze

a linear circuit with more than one independent
source by calculating the contribution of each
independent source separately.

6
4.3 Superposition Theorem (2)
We consider the effects of 8A and 20V one
by one, then add the two effects together
for final vo.

7
4.3 Superposition Theorem (3)
Steps to apply superposition principle

1. Turn off all independent sources except one

source. Find the output (voltage or current)
due to that active source using nodal or
mesh analysis.

2. Repeat step 1 for each of the other independent

sources.

3. Find the total contribution by adding

algebraically all the contributions due to the
independent sources. 8
4.3 Superposition Theorem (4)
Two things have to be keep in mind:

1. When we say turn off all other independent

sources:
➢ Independent voltage sources are replaced
by 0 V (short circuit) and
➢ Independent current sources are replaced
by 0 A (open circuit).

2. Dependent sources are left intact because

they are controlled by circuit variables.

9
4.3 Superposition Theorem (5)
Example 2

Use the superposition theorem to find

v in the circuit shown below.

3A is discarded
by open-circuit

6V is discarded
by short-circuit

*Refer to in-class illustration, text book, answer v = 10V 10

 4.3 Superposition Theorem (6)
Example 3

Use superposition to find vx in

the circuit below.

2A is discarded by
open-circuit 10V is discarded
Dependant source
by open-circuit
keep unchanged
20 W v1 20 W v2

+ 4W 0.1v1
10 V − 2A
4W 0.1v2

(a) (b)
11
*Refer to in-class illustration, text book, answer Vx = 12.5V
4.4 Source Transformation (1)

• An equivalent circuit is one whose v-i

characteristics are identical with the
original circuit.
• It is the process of replacing a voltage
source vS in series with a resistor R by a
current source iS in parallel with a resistor
R, or vice versa.

12
4.4 Source Transformation (2)
+ + • The arrow of the
current source is
directed toward
the positive
-
(a) Independent source transform
- terminal of the
voltage source.

+ + • The source
transformation is
not possible when
R = 0 for voltage
- - source and R = ∞
(b) Dependent source transform for current source.

13
 4.4 Source Transformation (3)
Example 4

Find io in the circuit shown below using source transformation.

*Refer to in-class illustration, textbook, answer io = 1.78A 14

 4.5 Thevenin’s Theorem (1)
It states that a linear two-terminal
circuit (Fig. a) can be replaced by an
equivalent circuit (Fig. b) consisting
of a voltage source VTH in series with
a resistor RTH,

where

• VTH is the open-circuit voltage at the

terminals.

• RTH is the input or equivalent resistance at

the terminals when the independent
sources are turned off.

15
 4.5 Thevenin’s Theorem (2)
Example 5
6W 6W
Using Thevenin’s theorem,
find the equivalent circuit to
the left of the terminals in 4W RTh

the circuit shown below.

Hence find i. (a)

6W

+
2A 6W 4W VT
2A
h
−

(b)

16
*Refer to in-class illustration, textbook, answer VTH = 6V, RTH = 3W, i = 1.5A
 4.5 Thevenin’s Theorem (3)
5W Ix 3W a
Example 6
+
Find the Thevenin equivalent 6V
+
− i1
i2 VTh
4W −
circuit of the circuit shown 1.5Ix
below to the left of the i1 i2

terminals. o
b
(a)

0.5I 3W Ix a
i
x

5W 1.5Ix 4W + 1V
−

(b)
b
17
*Refer to in-class illustration, textbook, answer VTH = 5.33V, RTH = 3W
 4.6 Norton’s Theorem (1)
It states that a linear two-terminal circuit
can be replaced by an equivalent circuit
of a current source IN in parallel with a
resistor RN,

Where

• IN is the short circuit current through

the terminals.

• RN is the input or equivalent resistance

at the terminals when the independent
sources are turned off.

The Thevenin’s and Norton equivalent circuits are

related by a source transformation. 18
 4.6 Norton’s Theorem (2)
Example 7 2vx
i
+ −
Find the Norton equivalent + +
vx vx +
circuit of the circuit shown −
6W
ix
2W
− 1V −
below.
(a)

2vx

+ −
+
vx Isc
6W 10 A 2W
−

(b)

19
*Refer to in-class illustration, textbook, RN = 1W, IN = 10A.
4.7 Maximum Power Transfer (1)
If the entire circuit is replaced by
its Thevenin equivalent except for
the load, the power delivered to
the load is:
2
 VTh 
P = i 2 RL =   RL
 RTh + RL 

For maximum power dissipated

in RL, Pmax, for a given RTH,
and VTH,
2
V
RL = RTH  Pmax = Th
4 RL The power transfer profile with
different RL 20
4.7 Maximum Power Transfer (2)
Example 8

Determine the value of RL that will

draw the maximum power from
the rest of the circuit shown below.
Calculate the maximum power.

vx 4W vx 4W
+ −v0 + −

i
Fig. a
2W 2W
+
1W 1W
VTh => To determine RTH
+ 1V + 9V io −
+
− −
+
Fig. b
− −
3vx 3vx
=> To determine VTH

(a) (b)

*Refer to in-class illustration, textbook, RL = 4.22W, Pm = 2.901W 21