Camera Operation Manual
Uploaded by
vararduvarCamera Operation Manual
Uploaded by
vararduvarC ID 1043345 : S01 camera operation manual
The device consists of a board with a slot for a memory card TF.
ON-OFF switch
USB port
3 push-buttons ( under the protective film)
A ribbon cable with the camera.
A microphone
Normally operate the camera by remote control, but it can also be operated with the hidden buttons on the
unit.
1 Start up:
Put the power switch in the ON position. (move the lever towards the red cable).
lever USB
Video=B
ON-OFF
Photo=C
Stand-by=A
LEDS
mic
The RED an BLUE Leds are located inside the unit and can be seen by looking into the unit
near the microphone.
To place the unit in standby mode, you must press long the A button of the remote control.
After pressing:
The red LED goes on and stays on
The blue LED goes on for three (3) seconds.
The device vibrates long
A other push on the A button of the remote control put the device in a sleep mode
Blue LED flashes 3 times
Red LED goes OFF
The device vibrates short
2 Camera : constantly recording video
The device has to be in stand by mode, so the red LED is on.
Press button B of the remote control to start camera recording
Red led flashes 3 times and goes out
The device vibrates short and make video recordings.
Stop recording with the camera by pressing the B button again
Red Led comes on and stays on.( stand by mode)
The device vibrates two times.
3 Picture:
A picture can be taken by pressing the button C on remote control when the device is in
stand by mode .
Blue LED flashes once
Red goes out and on again
The device vibrates short
Picture is taken every time the button C of the remote control is operated
4 Motion detection:
This option can be used for stand alone working. The camera will make a video of 1 min every
time a movement is detected.
When the device is in standby mode, then a short press the D button on the remote control
brings the unit in the motion detection mode.
The blue LED blinks twice and turns off.
The red LED turns off.
The device vibrates two times ( motion detection ON)
Press again the button D to bring the unit in standby.
Red LED lights up permanently( stand by mode)
The device vibrates three times ( motion detection OFF)
5 Low battery or no memory:
The device vibrates six times .
All LEDs OFF
USB connection:
The device act as a external disk drive when it is connected to a USB port of a computer.
The device vibrates once when it is connected to a powered USB port.
The battery is also charged by the USB port.
During charging the battery, the blue LED is solid and the red LED flashes . The red LED stops flashing
when the battery is fully charged
Note:
1.
The timestamp on the pictures and the videos can been set by loading a “ time.txt” document on the
external disk drive.
The time file must contain the correct date and time. See example
When the device is powered up again and set into stand-by . The new time will be set and the file time.txt
will be erased.
When the battery is disconnected or is completely empty, the time must be set back by loading a time.txt file
containing the correct time and date.
2
When the remote control does not work or de red led on the remote control does not lit , replace the battery.
The device can also operate by pushing the buttons on the device body. The buttons are on the side of the
board, under the protective film
Product parameters:
Resolution 1920*1080/720p
Power dissipation 220 mA/h
Lens wide angle 140 degr /oem: 90 degr
Lens line long: 15 cm
Memory Up to 32 Gbyte
Frame rate 30 fps
Photo 4032x3024
Weight 150 gr
Battery 3800mAh
Distance control 5-8 meter
Battery LxWxH 83x50x10 mm
Device body LxWxH 53x28x10xmm
Remote controle:
Red LED (lit when pressing a button)
A B
A: switch stand by ( toggle)
C D B: switch video recording ( toggle)
C: take photo
A: motion detection ( toggle)
Remote controle
