Scribd
Upload
123 views5 pages

User Manual HT2

Uploaded by

danecuprija
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
123 views5 pages

User Manual HT2

Uploaded by

danecuprija
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

User manual

HITAG-2 programmer
www.simonandtony.com

User Manual Doc Nr: 01


HITAG-2 Programmer Date: 15.04.2008/V4.0.0.0
WWWSIMONANDTONY.COM
-2-
Table of Content
1 INTRODUCTION........................................................................................................................................
2 HARDWARE REQUIREMENTS................................................................................................................
3 INSTALLATIONS.........................................................................................................................................
4 USING OF PROGRAMMER......................................................................................................................
5 NOTES ABOUT HITAG-2 TRANSPONDERS...........................................................................................
Revisions
Changes to the previous version are shown in italic.
Date Sym Description ´new rev.
23-Feb-2008id Initial Release 1.0
03-Nov-2008 id Changes in document according applied new software version 4.0.0.0
08-Nov-2008 id Changes in document according applied new software version 4.0.0 User Manual Doc Nr: 01
HITAG-2 Programmer Date: 15/04.2008/1.00
WWW.SIMONANDTONY.COM
-3-

1 Introduction
HITAG-2 programmer is device programmer intended for programming of HITAG-2 transponders
Compatible with PHILIPS PCF7936 transponders. It can be used for reading/programming of
following
Type transponders:
PCF7936
PCF7941
PCF7942
PCF7944
PCF7946
Compatible with mentioned above
Programmer supports both modes – PASSWORD and CIPHER mode

Fig.1 PCF7936 transponder

User Manual Doc Nr: 01


HITAG-2 Programmer
WWW.SIMONANDTONY.COM
-4-

2 Hardware requirements
· IBM compatible PC running Windows™ 95/98/ME/2000/NT4/XP
· VGA display card (800x600)
· USB port
3 Installation
Connect your programmer to USB port and follow instructions in the documents bellow depends
of
your operation system.
Windows_98_Installation_Guide.pdf
Windows_XP_Installation_Guide.pdf
Windows_2000_Installation_Guide.pdf
Once driver installed your PC will be equipped with additional virtual COM port.
Go in “my computer/properties” -> “hardware” -> “device manager” -> “Ports” and check which
COM
port number is installed.
Fig.2 USB serial port
User Manual Doc Nr: 01
HITAG-2 Programmer
WWW.SIMONANDTONY.COM
-5-
Now you can start software of your programmer “HT2.exe” will appears following screen:
Fig.3 Main screen of the program

From “Settings”->”COM port” you have to adjust number of “USB COM port” installed on your PC.
Next urgent step before start working with programmer is to adjust your antenna factor.
Adjusting can be done when reading some transponder using button “Quick Read” and change
factor
to 4,5,6 and s.o. until is reached best reading (i.e. each attempt for reading leads to results like
previous).
While manufactory programmers are adjusted to have best factor “6” but deviation are possible
depends
Of your working place.
User Manual Doc Nr: 01
HITAG-2 Programmer
WWW.SIMONANDTONY.COM
-6-

4 Using of programmer
Put transponder on it place (refer Fig.4)

Fig.4 transponder place


Before reading or programming of transponder you must choice working mode of transponder
PASSWORD or CIPHER mode.
Take into account that transponders can be read or program if you know PASSWORD of
transponder
(PASSWORD/ CRYPTO WORDS LO+HI).
We have 9 different buttons for reading (“Read All” and 8 “R” separate for each page of
transponder)
and also 8 buttons for programming (“Write All” and 7 “W” for each programmable page of
transponder).
Bellow is example – content from key of Porsche Cayenne – PCF7946
User Manual Doc Nr: 01
HITAG-2 Programmer
-7-

5 Notes about HITAG-2 transponders


Please before programming of some transponder refer corresponding documents which describes
features
of transponder.
Transponder must be programmed very carefully because in some of bits from configuration of
transponder
can be programmed only once which leads partial reading or programming of transponder.
Additionally changing of password/ISK must be documented always to allow following reading or
programming

User Manual Doc Nr: 01


HITAG-2 Programmer
WWW.SIMONANDTONY.COM
-7-

5 Notes about HITAG-2 transponders


Please before programming of some transponder refer corresponding documents which describes
features
of transponder.
Transponder must be programmed very carefully because in some of bits from configuration of
transponder
can be programmed only once which leads partial reading or programming of transponder.
Additionally changing of password/ISK must be documented always to allow following reading or
programming.

You might also like