26/11/24, 18:26 FS-Quiz - Play
FS-Quiz
ID: 196
Question: 1
Which parameters are not required to calculate the operating temperature of a conductor in
open air?
Material
Insulator (coating)
Conductor length
Operating current
Ambient temperature
Cross section area
Operating voltage
Cross section shape
ID: 197
Question: 2
A car finishes the skidpad event with an average laptime of 5,0 seconds. The static friction
coefficient of the ground and the tire is 0,9. What was the aerodynamic downforce to weight
ratio during the run? Assume, that the car is travelling on the centerline of the track.
G=9,81 m/s²
0.45
0.9
0.5
1.37
ID: 198
Question: 3
If a thin and infinitely long fibre's diameter is reduced, which of its properties from the following
will increase?
Strength
Young modulus
Peak force at failure
Stiffness
https://fs-quiz.eu/quiz/20 1/5
26/11/24, 18:26 FS-Quiz - Play
ID: 199
Question: 4
At least how many TS voltage measurements have to be in the electrical system?
2
0
1
3
ID: 200
Question: 5
According to the FS Rules 2019, how many points will a team score eventually on the Cost and
Manufacturing Event, if the team is not in the final, the score awarded to a team during the initial
judging is 79 points, while the highest score awarded to any team not participating in the finals is
91 points?
79
82,5
86,8
95
ID: 201
Question: 6
Our vehicle completes the Acceleration Event. Its velocity is 126km/h, when it crosses the finish
line. How much time did it need to complete the run, if we assume, that its acceleration is
constant during the run?
4,28s
4s
4,56s
3,86s
ID: 202
Question: 7
The circular Dynamic Platform at ZalaZone has 1% of slope from North to South. The diameter of
the Platform is 300 m. If a ball is released on the highest point of the Platform (North), from
standstill state, what will be the speed of the ball at the lowest point of the Platform (South)?
Consider that the ball rolls directly from the highest point to the lowest point.
Rolling resistance is 0
https://fs-quiz.eu/quiz/20 2/5
26/11/24, 18:26 FS-Quiz - Play
Mass of the ball is 200g
G = 10 m/s²
5,897 m/s
5,897 km/h
7,7459 m/s
7,7459 km/h
ID: 203
Question: 8
In which Cost Report Document does the team need to list the research and developement
costs?
In neither of the Cost Report Documents
In the Cost Explanation File
In the CBOM
In the DBOM
ID: 204
Question: 9
Can a team be eliminated from the Engineering Design Event by the judges, if every document of
theirs was accepted and they are present at the Engineering Design Event?
Yes, if the team did not pass any scrutineering prior.
Yes, if the judges consider the vehicle to be in unfinished state.
No, if a team is present at the event, the judges are obligated to evaluate their performance.
Yes, if the judges consider the number of the team members present at the discussion
insufficient.
ID: 205
Question: 10
You are competing on the Endurance event. Unfortunately one of the throttle pedal return
springs is already broken, but the car operates well. In the long straigth the other return spring
breaks too but the driver doesn't recognize it, and the throttle pedal get stuck at 100%. At the
end of the straight, the driver reaches a slalom and pushes the break with medium force. What
happens after that?
https://fs-quiz.eu/quiz/20 3/5
26/11/24, 18:26 FS-Quiz - Play
The breaks are ineffective to slow down the car while the motors are producing full power,
driver looses control over the car, hits all cones at high speed and tries to deactivate TS by
pushing the cockpit killswitch.
TS may remain active, the vehicle can go trough the slalom but won't be able to gain speed
anymore.
BSPD immediately shut down the TS as the driver touches the break pedal.
The motors, and therefore the racecar, immediately stop at the end of the straight.
ID: 206
Question: 11
Which of the listed material can be described with the following fictional mechanical properties?
Specific strength (σ[MPa]/ρ[g/cm³]) = 1656
Specific modulus (σ[GPa]/ρ[g/cm³]) = 57
Failure Strain (%) = 1,8
Steel
Aramid Fiber Reinforced Polymer
Titanium
Carbon Fiber Reinforced Polymer
ID: 207
Question: 12
The Zalazone Proving Ground would contain several track elements (such as Dynamic Platform,
Slopes, Handling Course etc.) In which phase of the construction it is planned to contruct the
High - Speed Oval Track element?
Phase 4
Phase 1
Phase 3
Phase 2
ID: 208
Question: 13
What does the yellow and red striped flag mean during Endurance and Autocross Event?
The track is slippery or something is on the racing surface that should not be there. The driver
must be prepared for evasive maneuvers to avoid the situation
Mechanical black flag. The driver must pull into the driver change area for a mechanical
inspection of the vehicle, something has been observed that requires a closer inspection.
https://fs-quiz.eu/quiz/20 4/5
26/11/24, 18:26 FS-Quiz - Play
The driver must pull into the driver change area for discussion with the officials concerning an
incident. A time penalty may be assessed.
The driver must be prepared to overtake a slower car on the racing line.
ID: 209
Question: 14
Which of the following dynamic disciplines will be organized first time in 2019 at FS East?
AutoX Event
Trackdrive Event
Driverless AutoX Event
Driverless Skidpad Event
ID: 210
Question: 15
Which of the following requirements is a must for all types of vehicles, when moving the vehicle
on the competition site other than on the practice or competition tracks?
Vehicles must be pushed at a normal walking pace by means of a red pushbar, equipped with
a fire extingusher.
Detached master switch.
Two team members walking on either side of the vehicle.
A registered driver wearing the required driver equipment as defined in T 13.3 except for
helmet, arm restraints and balaclava having full control of steering and braking.
Submit
Contact
Statistics
Legal notice
Privacy Policy
Created by Yannik Ottens · © 2024
https://fs-quiz.eu/quiz/20 5/5
