PDMS COMMANDS

PIPING COMMANDS.
1. ADD ALL PIP
2. REM ALL PIP
3. MOVE U THROU IDP@
4. MOVE E THROU IDP@
5. MOVE W THROU IDP@
6. MOVE N THROU IDP@
7. MOVE S THROU IDP@)
8. Q STEXT
9. Q ATT
10. REPR INSU ON/OFF UPDATE
11. Q ISPEC
12. ISPEC NULREF
13. CONN NEXT
14. FCONN
15. DIST 500
16. AXES AT PH
17. AXES AT PT
18. AXES OFF
19. BY U 500
20. BY D 500
21. BY E 500
22. BY W 500
23. BY S 500
24. BY N 500
25. Q NAME
26. ROTATE BY 45
27. ROT BY 90 ABOUT Z THRO ID@
28. Q PARA
29. Q CATREF
30. Q POS IN WORLD
31. CH CE
32. Q SPREF
33. Q ORI
34. DIR D
35. Q P1/P2/P3
36. Q HBORE
37. Q TBORE
38. Q LBORE
39. NEW BRA COPY PREV BY E/W/S/N/U/D 100
40. QU
41. Q ANGLE
42. THRO NEXT
43. Q LTLE
44. Q MEM
45. CONN IDP@ TO IDP Q CE
46. Q PL
47. BRA CONN PH TO FIST MEM
48. BRA CONN PT TO NOZZ ID@
49. BRA CONN PT TO LAST

Page 1 of 5
 50. RAD 500
51. HEI 500
52. BACK
53. FORW
54. NEW TEE/CAP/ELBOW etc.
55. TDIR
56. Axes at CE= to check the axes of component like North, South, East, West direction

57. Q axes at ph= to check the head of the branch of the pipe.

58. Q axes at pt= to check the tail of the branch of the pipe.

59. Q Hstu= to show the branch head tube attribute

60. Q Lstu= to show the branch tail tube attribute

61. Q Hbore= to check the arrive bore or diameter of the component

62. Q Tbore= to check the leave bore or diameter of the component

63. Q Spre= to check the specification of the particular component

64. Q pspec= to check material class of the pipe.

65. New elbow choo all= to create new elbow through command line

66. New tee choo all= to create new tee through command line

67. New gasket choo all= to create new gasket through command line

68. New flange choo all= to create new flange through command line

69. New olet choo all= to create new olet through command line

70. Unclaim all= to remove claim the by user so other user can work in that pipe, equipment,

member,structure.

71. Getwork= to refresh the design model. After get work all the change done any user will

show in the model.

72. Axes at hpos= To check the branch head axes

73. Axes at tpos= To check the branch tail axes

74. Q ltle= to check the length of the spool between the two component

75. Conn ph to fir member= to connect the branch head to first member of the next branch by

common line

76. Conn pt to fir member= to connect the branch tail to last member of the next branch by

common line

77. Q ori = to check the orientation of the component

78. Dist= to give the distance between two component

Page 2 of 5
79. Clea= to give the spool length between the two component

80. Conn= connect to the member

81. Fconn= to component forcefully

82. Q styp= to check the component selection type

83. Q dtxr= to check the detail text description of the component

84. Q mtxx= to check the material of the component

85. Q mode= to check the mode weather it in forward mode or backward mode

86. Q para= to check the parameter of the component

87. Dir tow next= to connect the next member by direction

88. Q ref= to check the reference

89. Add all the pipe within vol ce 500= all pipes to added in the area 500 around the selected

component.

90. Incl= to include the component from one branch to other branch

91. Ori and p3 is up= to orientate the point 3 of the tee in up direction

92. Own= navigate the owner of component

93. Q angle= to check the angle of the component

94. Q atle= to check the length of the first tube of the branch

95. Attype ccnn= comment attachment without dimensions

96. Attype cccc= comment attachment with dimensions

97. Attype xxxx= to set the attachment for isometric break up

98. Ch ce= to check the data inconsistency

99. Dir tow next elb= to align the elbow with next elbow

100. Dir tow id@= to align the elbow by using mouse click on the component

101. Q hcon= to check head connection attached with which branch

102. Q tcon= to check tail connection attached with which branch

103. Q ispec= to check the insulation of pipe

104. Ispec nulref= to remove the insulation of the pipe

105. Mtoc dotd= to appear the component in doted in the isometric

106. Mtoc off= to remove the material off the component. With this command material of the

component will not appear in isometric

Page 3 of 5
107. Nex conn= connect to next component

108. Nex thro ce= align the next component in same direction

109. Q p3 = to check the p3 point of the component

110. Q pa= to check arrive point

111. Q pl= to check the leave point

112. Attype flow= to create the flow direction attachment

These are the few commands which are using in the PDMS equipment design module.

113. New site= for creating the new site in pdms

114. New zone= for creating the new zone in pdms
115. New equi= for creating the new equipment in pdms
116. New sube= for creating the new sub equipment in pdms
117. New nozzle= for creating the new nozzle in the pdms
118. New box= for creating new box in the pdms
119. New cylinder= for creating new cylinder in the pdms
120. Conn idp to idp= to connect design point of two cylinder/box etc.
121. Mark with (nam) all nozz for ce= to mark the all nozzle of equipment with name in
pdms
122. Q level= to check the level of the component
123. Axes at p1= to check p1 point of the primitive
124. Axes at p2= to check p2 point of the primitive
125. New cylinder copy prev by n 500= to copy the previous cylinder by north direction by
500

126. For Drain pipe

a. ADD ATT
b. Q ATT
c. TCONN OPEN
d. Q STEXT
e. STEXT ‘DRAIN POINT’
127.For Slope Line /Rotated Elbow
a. FORWARDS
b. DIR TOW NEXT
c. BACKWARDS
d. DIR TOW NEXT
128.Q PA BOP/TOP
129.Q LSTUBE
130.Q HSTUBE
131.Q PSPEC
132.CONN PH TO P3 OF ID@
133.CONN PT TO LAS MEM

STRUCTURE COMMANDS.
1. AXES AT POSE/S
2. Q POSE WRT/*
3. EXTE END BY D 500 WRT/*
4. EXTE START BY U 500 WRT/*
5. EXTE END/START THRO ID@

Page 4 of 5
6. EXTE END/START THRO IDPL@
7. Q CUTL
8. Q POS PPLINE BOS IN/*
9. ADD ALL STR
10. REM ALL STR
11. Q ATT
12. BY U//D/E/W/N/S 500
13. Q DRNS DRNE
14. DRNSTART S 45 E
15. DRNEND S 45 W

EQUIPMENT COMMANDS.
1. ADD ALL EQUI
2. REM ALL EQUI
3. MOVE U THROU IDP@
4. MOVE E THROU IDP@
5. MOVE W THROU IDP@
6. MOVE N THROU IDP@
7. MOVE S THROU IDP@
8. REPR HOLES ON/OFF UPDATE
9. REPR OBST ON/OFF UPDATE
10. BY U//D/E/W/N/S 500
11. NEW BOX COPY PRE
12. NEW BOX XLEN 400 YLEN 250 ZLN 150
13. NEW CYL COPY PRE
14. NEW PYRE COPY PRE
15. NEW NOZZ COPY PRE
16. NEW BOX COPY PRE ROT BY 90 ABOUT Z THRO IDP@

1. ADD ALL WITHIN VOL CE (ADDS ALL DISCIPLINES THAT OVERLAP CE)
2. ADD ALL WITHIN VOL CE 100 (ADDS ALL DISCIPLINES THAT OVERLAP CE WITH A
VOLUMEOF 100mm ALL ROUND)

Page 5 of 5