Page 1 of 5

SLAB DESIGN CALCULATIONS

Project Name : Proposed One-Storey with Basement Residence_ Military Cut-off_ B.C.
Client Name : Sps. Geofrey C. Gerardo & Charon G. Gerardo
Engineer Name : nic
Analysis File : E:\Staad Connect 2024\Job.03.Gerardo Police haus\Column and Beam
Design.STD
Analysis Last Modified : 2/7/2024 6:11:52 PM

NOTES:
1. Density of concrete assumed as 25 kN/cum.

Definitions Of Terms: :
Ratio of flexural stiffness of beam section to flexural
1. αf =
stiffness of slab.
Ratio of torsional stiffness of edge beam section to flexural
2. βt =
stiffness of slab.
3. Φt = Strength reduction factor.
4. As = Area of Tension reinforcement required in 'sqmm'.
5. As,min = Min area of flexural reinforcement in 'sqmm'.
Area of longitudinal reinforcement provided at given section
6. AstPrv =
in 'sqmm'.
Total area of longitudinal reinforcement calculated at a
7. Ast =
given section in 'sqmm'.
8. b = Width of the Slab in 'mm'.
9. B1 to B4 = Width of beams around slab in 'mm'.
10. Cc = Effective Cover to tension reinforcement in 'mm'.
cross-sectional constant to define torsional properties of slab
11. CA and CB =
and beam.
12. deff = Effective depth of slab in 'mm'.
13. D1 to D4 = Depth of beams around slab.
14. Icr = Moment of Inertia of concrete crack section.
Length of clear span in direction that moment are being
15. Ln =
determined in 'mm'.
16. L2 = Length of adjacent span of Ln in 'mm'.
17. lb1 to lb2 = Moment of inertia of beams around slab in 'mm4'.
18. Mcr = Cracking Moment.
19. Mu = Factored Bending Moment at a section in 'kNm'.
20. Ptmin = Minimum percentage steel as per chapter 8.
21. PtPrv = Provided percentage steel.
22. Vc = Nominal shear strength provided by concrete in 'kN'.
23. Vu = Factored Shear Force at a section in 'kN'.
24. Vud = Design Shear Force in 'kN'.
25. y = Neutral axis depth.

Code References :
NSCP C101 - 2015

file:///C:/Users/user/AppData/Local/Temp/tmp4417.tmp 2/8/2024
 Page 2 of 5

Item CLAUSE / TABLE

1. Ptmax : 407.3.3.1, 408.3.3.1, 409.3.3.1
2. Ptmin : 407.6.1.1 & 408.6.1.1/407.7.2.3
3. Vc : 422.6.5
4. Av : 422.5.10.5 & 422.6.7
5. Moment calculations : 408.10
6. spacing between main bars : 407.7.2
7. spacing between distribution bars : 407.7.6 & 408.7.2
8. Minimum reinforcement : 407.6.1 & 408.6.1
9. fs,perm : 424.3.2.1
10. fc,perm : A.3.1 (ACI 318-99)
11. Wcr : Eq 1-2 ( ACI 224R-01)

Slab No. : S1
Level = 7.5 m
Design Code = NSCP C101 - 2015
Grade Of Concrete = C21
Grade Of Steel = Fy227
Clear Cover = 12.000 mm
Long Span, Ly = 3.000 m
Short Span, Lx = 3.000 m
Imposed Load = 1.000 kN/sqm
Live Load, Qk = 1.900 kN/sqm
Slab Thickness = 125.000 mm
Effective Depth Along LX, Deffx = 108.000 mm
Effective Depth Along LY, Deffy = 98.000 mm
Self Weight = 3.120 kN/sqm
Total Load, TL (ultimate) = 7.990 kN/sqm
Span = 2-Way
Load Combination = 1.2 DL + 1.6 LL

Short Span Long Span

Side1 Side2 Side1 Side2
Beam
B (mm) 250 250 250 250
D (mm) 400 400 400 400
Ib (mm4) x106 1333.33 1333.33 1333.33 1333.33
Adjacent Slab
Thk (mm) 125 - - 125
Span (mm) 3000 - - 3000
Ib (mm4) x106 488.28 244.14 244.14 488.28
αf lx, αf ly 2.73 5.46 5.46 2.73
αf 4.1
Ln (mm) 2750 2750
L2 (mm) 1625 1625
Effective Width (mm) 750 750

file:///C:/Users/user/AppData/Local/Temp/tmp4417.tmp 2/8/2024
 Page 3 of 5

Ly/Lx Lx/Ly
1 1
Total BM (kNm) 12.27 12.27
Bottom
Moment Co-efficent 0.57 0.57
Distributed Moment (kNm) 7 7
Moment factor for CS 0.750 0.750
CS Moment (kNm) 5.25 5.25
MS Moment (kNm) 1.75 1.75
Moment on Beam (kNm) 4.46 4.46
Design Moment M1, M3 (kNm) 1.75 1.75
Top
Moment Co-efficent 0.7 0.7
Distributed Moment (kNm) 8.59 8.59
Moment factor for CS 0.750 0.750
CS Moment (kNm) 6.44 6.44
MS Moment (kNm) 2.15 2.15
Moment on Beam (kNm) 5.48 5.48
Design Moment M2, M4 (kNm) 2.15 2.15

Design Moments:
Short Span Positive Moment At Midspan -
M1 = 1.750 kNm
M1 (per m) = M1/Effective
Width
= 2.330 kNm/m
Area Of Reinforcement = 225.000 sqmm/m
Required (BM)
Reinforcement Provided = D12 @ 250 C/C
= 452.000 sqmm/m
Short Span Negative Moment At Continuous Support -
M2 = 2.150 kNm
M2/Effective
M2 (per m) =
Width
= 2.860 kNm/m
Area Of Reinforcement = 225.000 sqmm/m
Required (BM)
Reinforcement Provided = D12 @ 250 C/C
= 452.000 sqmm/m
Long Span Positive Moment At Midspan -
M3 = 1.750 kNm
M3/Effective
M3 (per m) =
Width
= 2.330 kNm/m
Area Of Reinforcement = 225.000 sqmm/m
Required (BM)
Reinforcement Provided = D12 @ 250 C/C
= 452.000 sqmm/m
Long Span Negative Moment At Continuous Support -
M4 = 2.150 kNm

file:///C:/Users/user/AppData/Local/Temp/tmp4417.tmp 2/8/2024
 Page 4 of 5

M4/Effective
M4 (per m) =
Width
= 2.860 kNm/m
Area Of Reinforcement = 225.000 sqmm/m
Required (BM)
Reinforcement Provided = D12 @ 250 C/C
= 452.000 sqmm/m
Distribution Reinforcement @ 0.18% -
Area Of Reinforcement = 225.000 sqmm/m
Required
Reinforcement Provided = D12 @ 300 C/C
= 377.000 sqmm/m

file:///C:/Users/user/AppData/Local/Temp/tmp4417.tmp 2/8/2024
 Page 5 of 5

Shear Check :
Along Short Span
Vsx (TL(ultimate) x Lx / 4) = 5.990 kN
Nominal Shear, ΦVc = 62.620 kN
> 5.990 Slab Is Safe In Shear
Along Long Span
Vsy (TL(ultimate) x Lx / 2 x = 5.990 kN
(1 - (Lx / (2 x Ly))))
Nominal Shear, ΦVc = 56.820 kN
> 5.990 Slab Is Safe In Shear

file:///C:/Users/user/AppData/Local/Temp/tmp4417.tmp 2/8/2024