Pentathane HS 4510

Polyurethane Top Coat

PRODUCT DESCRIPTION
It is Aliphatic - Acrylic Polyurethane Coating containing high Titanium di oxide content and based on
Eco friendly Trimmer Technology . It has a high degree of gloss retention properties.

This product has High Volume Solid and in a blend of Nano Technology and Eco friendly additives.
Product is resistant to all type of mild chemicals , Oils , lubricants spillage . When applied over properly
primed surface forms a very densely cross linked film with lowest permeability to water vapors.

Product is based on very Fast Cure Technology ,which can be put the painted surfaces in early services
___________________________________________________________________
INTENDED USES For application on clean and primed steel surfaces. It recommended for structures in Refineries,
Chemical Plants, exterior of tanks & pipelines in marine weather.

Provides excellent adhesion and out standing UV resistance for protection in industrial, coastal structures,
pulp and paper plants, bridges and offshore environmental in both atmospheric exposure.
_________________________________________________________________________

PRACTICALINFORMATION FOR Pentathane HS 4510

Color Available as per shade card .

Gloss Level High Gloss of 90% at 60 degree.

Volume Solids 57±2 %

Typical Thickness 50-60 microns dry equivalent to 90– 105 microns wet

Theoretical Coverage 9.50 m2/liter at 60 microns D.F.T. at stated VS

Practical Coverage Allow appropriate loss factors

Method of Application Airless spray, Brush , Trowels , Rollers

Drying Time & Over Coating Intervals.

Over coating Interval Over coating Interval with

of Pentathane HS 4510with self recommended topcoats

Touch Hard
Temperature Dry Dry Minimum Maximum Minimum Maximum

25oC (77oF) 2 hours 16 hours 8 hours Extended 16 hours Extended

40oC (104oF) 1 hours 8 hours 6 hours Extended 8 hours Extended

__________________________________________________________________
REGULATORY DATA
Flash Point Base (Part A) C/A (Part B) Mixed

240C 240C 240C

______________________________________________________________
Pentathane HS 4510
Polyurethane Top Coat

PRODUCT CHARACTERISTICS
In order to achieve best performance with this product ensure the best surface preparation. When applied
primer coat by brush & Rollers ensure thorough wetting out of the substrate by Pentathane HS 4510 .

Maximum film build in one coat is best attained by airless spray. When applying by methods other than
airless spray, the required film build is unlikely to be achieved.

Pentathane HS 4510 can be applied up to 100 Microns DFT in a single coat by airless spray as a part
of Protective coating system as per ISO-12944

Best Gloss & finish can be achieved when applied by Air assisted Gun

Surface temperature must always be a minimum of 3° C (5° F) above dew point.

Product is based on fast cure technology & surface can be taken for the early services other than
exposure to the mild chemicals. Early Foot / Equipments traffic is possible after 16 Hrs of Drying.

For chemical resistance complete cure of 7 days at 25°C or 4 Days at 40°C must be given.
_________________________________________________________________
SYSTEMS COMPATABILITY
Pentathane HS can be applied over almost all type of well primed metal structures .

Suitable Primers & Intermediate

__________________________________________________________________________________
SURFACE PREPARATION
The performance of this product will depend upon the degree of surface preparation.

The surface to be coated must be clean, dry and free from contamination. Prior to Top coat application,
all surfaces should be assessed and treated in accordance with ISO 8504:1992.

This product must be applied on properly prepared Primed surface , all contamination must be removed
from the surface by wiping with solvent or by using dry bristles brush. This top coat is the part of High
performance anti corrosive scheme
____________________________________________________________________
APPLICATION
Mixing Material is supplied in two containers as a unit. Always mix a complete
unit in the proportions supplied. Once the unit has been mixed it must be
used within the working pot life specified.

(1) Agitate Base (Part A) with a power agitator.

(2) Combine entire contents of Curing Agent (Part B) with Base
(Part A) and mix thoroughly with power agitator

Mix Ratio 9.0 parts: 1.00 parts by volume

Working Pot 15o C 25oc 40o C

Life 2.5 hours 2 Hrs. 1.5Hrs.
Addition of Small Quantity of thinner to this will increase pot life by few
minutes. Add thinner 165 before adding Curing Agent ( Part B

Airless Spray Recommended - Tip range 0.28-0.43 mm (11 -17 thou)

- Total output fluid pressure at
spray tip not Less than 176
kg/cm2 (2,500 p.s.i)
 Pentathane HS 4510
Polyurethane Top Coat

Air Spray Recommended Gun DeVilbiss MBC or JGA or Equivalent.

Air Cap 704 or 765
Fluid Tip E.
Brush / Roller Recommended Typically 50-60 microns can be achieved

Thinner Thinner 165 Normally No thinner is Required , if required

for ease Of application Add Max . 15 % by
Volume . Do not thin more than allowed by
by local Environmental legislation.

Cleaner Thinner 165

Work Stoppages Do not allow material to remain in hoses, gun or spray

equipment.Thoroughly flush all equipment with Thinner 165. Once
unitsof paint have been mixed they should not be resealed and it is advised
that after prolonged stoppages work recommences with freshly mixed
units.

Clean Up Clean up all equipment immediately after use with Thinner 165 . It is good
working practice to periodically flush out spray quipment during the course
of the working day. Frequency of cleaning will depend upon amount
sprayed, temperature and elapsed time, including any delays.All surplus
materials and empty containers should be diagnosed of in accordance with
appropriate regional regulations / legislation
__________________________________________________________________________
SAFETY PRECAUTIONS

This product is intended for use only by professional applicators in industrial situations in
accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s),
and should not be used without reference to the Material Safety Data sheets (MSDS) which
Grauer & Weil India Ltd has provided to its customers.

All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety and Environmental standards and regulations.

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes
will be emitted which will require the use of appropriate personal protective equipment and adequate
local exhaust ventilation.

If in doubt regarding the suitability of use of this product, consult Grauer & Weil India Ltd for further
advice.
__________________________________________________________________________
PACK SIZE : 20 LTS
____________________________________________________________________________________________

Disclaimer
The information given in this sheet in not intended to be exhaustive and any person using the product for any purpose other than that specifically recommended
in this sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. Whilst we
endeavor to ensure that all advice we give about the product (whether in this sheet or otherwise) is correct we have no control over either the quality or condition
of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept
any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage (other than death or personal injury resulting from
our negligence) arising out of the use of the product. The information contained in this sheet is liable to modification from time to time in the light of experience
and our policy of continuous product development.
It is the user’s responsibility to check that this sheet is current prior to using the product. Issue date : April 2010