DC/DC Converters

TEM 2 Series, 2 Watt

Features UL 60950-1

u DIL-24 plastic package life

u Tightly regulated output End of
u Very low output noise
u Short circuit protection
u Operating temperature
range –25°C to +70°C
u I/O isolation 1’000 VDC
u Internal filter
u Industry standard pinout
u 3-year product warranty

The TEM 2 series is a family of isolated dc/dc converters in a DIP-24 package. They
offer tight line/load regulation and 1000 VDC I/O isolation. Standard features in-
clude an internal filter to reduce reflected input ripple currrent and to guarantee low
output noise. This product series provides a cost effective solution by many industrial
or consumer electronics appliactions.

Models
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TEM 2-0511* 5 VDC 400 mA 50 %
TEM 2-0512* 12 VDC 165 mA 54 %
TEM 2-0521* 5 VDC ±10% ±12 VDC ±80 mA 53 %
TEM 2-0522* ±15 VDC ±65 mA 51 %
TEM 2-1211* 5 VDC 400 mA 50 %
TEM 2-1212* 12 VDC 165 mA 56 %
TEM 2-1221* 12 VDC ±10% ±12 VDC ±80 mA 59 %
TEM 2-1222* ±15 VDC ±65 mA 59 %
TEM 2-2411* 5 VDC 400 mA 51 %
TEM 2-2412* 12 VDC 165 mA 61 %
TEM 2-2421* 24 VDC ±10% ±12 VDC ±80 mA 61 %
TEM 2-2422* ±15 VDC ±65 mA 61 %
* = End of life

http://www.tracopower.com Page 1 of 3
 DC/DC Converters
TEM 2 Series 2 Watt

Input Specifications
Input current no load 5 Vin models: 80 mA typ.
12 Vin models: 40 mA typ.
24 Vin models: 20 mA typ.
Surge voltage (1 sec. max.) 5 Vin models: 7.5 V max.
12 Vin models: 15 V max.
24 Vin models: 30 V max.
Input filter Pi-Filter
Output Specifications
Voltage set accuracy ±3 %
Regulation
– Input variation Vin min. to Vin max. ±0.3 % max.
– Load variation 10 – 100 % single output models: ±0.5 % max.
dual output models balanced load: ±1.0 % max.
dual output models unbalanced load: ±3.0 % max.
Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk max
Temperature coefficient ±0.02 %/K
Current limitation >120 % of Iout max., constant current
Short circuit protection indefinite
Capacitive load single output models: 470 µF max.
dual output models: 220 µF max.
General Specifications
Temperature ranges – Operating –25°C to +70°C
5 VDC output models: –25°C to +60°C
– Case temperature +95°C max.
– Storage –40°C to +125°C
Derating 3 %/K above +70°C
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >800‘000 Mio. h
Isolation voltage (60 sec.) – Input/Output 1’000 VDC
Isolation capacitance – Input/Output 100 pF typ.
Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm
Switching frequency 80 kHz typ. (Pulse frequency modulation PFM)
Safety standards cUL/UL 60950-1, IEC/EN 60950-1
Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf
– RoHS directive 2011/65/EU

All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

http://www.tracopower.com Page 2 of 3
 DC/DC Converters
TEM 2 Series 2 Watt

Physical Specifications
Casing material non conductive plastic (UL94V-0 rated)
Weight 12 g (0.42 oz)
Soldering temperature max. 260°C / 10 sec.

Outline Dimensions mm (inches)

1 2 3 10 11 12 Pin-Out
15.25 (0.60)

20.3 (0.80)

Bottom view Pin Single Dual

1 +Vin (Vcc) +Vin (Vcc)
24 23 22 15 14 13 2 NC –Vout
3 NC Common
10 –Vout Common
2.54
(0.10)

11 +Vout +Vout
12 –Vin (GND) –Vin (GND)
(0.40)
10.2

13 –Vin (GND) –Vin (GND)

14 +Vout +Vout
(0.18)

15 –Vout Common
4.5

22 NC Common
23 NC –Vout
2.54 2.54 17.78 (0.70) 2.54 2.54
(0.1) (0.1) (0.1) (0.1) 24 +Vin (Vcc) +Vin (Vcc)

2.0 27.94 (1.10) NC = not connected

(0.08)

31.8 (1.25)

Pin diameter ø 0.5 ±0.05 (0.02) ±0.002

Tolerances ±0.5 (±0.02)

Specifications can be changed any time without notice.

Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
Rev. June 6, 2024
www.tracopower.com Page 3 of 3