Scribd
Upload
7 views

Module-1

upda test exam support

Uploaded by

Abdelhamid Benallel
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
7 views

Module-1

upda test exam support

Uploaded by

Abdelhamid Benallel
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 11

Module-1

1. Tesla is a unit of:

field strength

inductance

flux density

flux
Correct Answer : c

Explanation : The tesla (symbol T) is the derived SI unit of magnetic flux density,
which represents the strength of a magnetic field. One tesla represents one weber
per square meter.

2. Excess-3 code is known as

Weighted code

Cyclic redundancy code

Self-complementing code

Algebraic code.
Correct Answer : c

Explanation : The excess-3 code (or XS3) is a non-weighted code used to express
code used to express decimal numbers. It is a self-complementary binary coded
decimal (BCD) code and numerical system which has biased representation.

3. Form Factor is the ratio of

average value/r.m.s. value

average value/peak value

r.m.s. value/average value

r.m.s. value/peak value


Correct Answer : c
Explanation : Form Factor is the ratio of RMS value / Average value

4. Three lamps are in circuit as shown in Figure given below. The lamp of 100
W will have maximum brightness when

key k1 is closed, k2 is open and k3 is closed

k1 is open, k2 is closed and k3 is open

k1 is open, k2 is closed and k3 is also closed

K1 is closed, k2 is open and k3 is also open.


Correct Answer : b

Explanation : If switch k1 is open,K2 is closed and k3 is open for the lamp of 100W
maximum brightness

5. For Which of the following is non-linear device:

Inductance

Wire wound resistor

Transistor

Condenser
Correct Answer : c

Explanation : The non-linear circuit is also an electric circuit and the parameters of
this circuit differ with respect to the current and the voltage

6. For a frequency of 200 Hz, the time period will be


0.05 s

0.005 s

0.0005 s

0.5 s
Correct Answer : b

Explanation : t= 1/f

7. Which of the following methods may be used to convert A.C. system to


D.C:

Rectifiers

Inverters

Cycloconverter

All of the above


Correct Answer : a

Explanation : Rectifier Converts AC into DC

8. The Thevenin equivalent voltage (VTH) is the short-circuit voltage between


two terminals in a circuit?

TRUE

FALSE

Correct Answer : b
Explanation : The Thevenin-equivalent voltage is the voltage at the output terminals
of the original circuit. When calculating a Thévenin-equivalent voltage, the voltage
divider principle is useful, by declaring one terminal to be Vout and the other
terminal to be at the ground point.

9. Transistors act basically as voltage sources

TRUE
FALSE

Correct Answer : b
Explanation : BJT is a current controlled device because the output characteristics of
BJT are determined by the input current.

10. Open circuit test on transformers is conducted to determine.

hysteresis losses

copper losses

core losses

eddy current losses


Correct Answer : c

Explanation : Open circuit test or no load test on a transformer is performed to


determine 'no load loss (core loss)' and 'no load current I0'. The circuit diagram for
open circuit test is shown in the figure below. Usually high voltage (HV) winding is
kept open and the low voltage (LV) winding is connected to its normal supply.

11. The output of a NOR gate is HIGH if ____________.

all inputs are HIGH

any input is HIGH

any input is LOW

all inputs are LOW


Correct Answer : d
Explanation :

12. A circuit breaker is a

Current Interrupting device

Power factor correcting device

Harmonic correcting device

All of the above


Correct Answer : a

Explanation : when current exceed the up normal value, its start work.

13. Induction motor operating at frequency of 50HZ,P=2 and no-load speed


2900 RPM. What is the slip frequency?

0.33 HZ

1.67 HZ

0.02 HZ

1.5 HZ
Correct Answer : b

Explanation : Ns = 120F/P = 120 x 50 / 2 = 3000 RPM S = Ns – Nr / Ns = 3000 –


2900 / 3000 = 0.0333 Slip Frequency = S x F = 0.033 x50 = 1.67 Hz

14. What is the transfer function (O/P / I/P) ?


[G1G2/(1+H1G2)] +G4

G1G2/1-G2H2 + G4

G1+ G2/1+G2H2 + G4

G1G2G4/1+G2H2
Correct Answer : a

15. Define the OP-AMP Circuit given below

Integrator

Differentiator

Band Pass Filter

Stop Band Filter


Correct Answer : a

Explanation : An integrator in measurement and control applications is an element


whose output signal is the time integral of its input signal. It accumulates the input
quantity over a defined time to produce a representative output. Integration is an
important part of many engineering and scientific applications.

16. We have 2 resistances R1 & R2. Resistance value is 4.5Ω when


connected in series and 1Ω when connected in parallel. Find R1 & R2

3Ω, 0.5Ω
1.5Ω, 0.5Ω

1.5Ω, 3Ω

1Ω, 3Ω
Correct Answer : c

Explanation : R1 + R2 = 4.5 and R1 R2 / R1 + R2 = 1 R1 R2 / 4.5 = 1 R1.R2 = 4.5


R1 = 4.5/R2 4.5/R2 + R2 = 4.5 R22 + 4.5 = 4.5R2 Solving above equation R2 = 3
ohm So R1 becomes 1.5 ohm

17. In By which of the following systems electric power may be transmitted:

Overhead system

Underground system

Both (a) and (b)

none of the above


Correct Answer : c

Explanation : An overhead power line is a structure used in electric power


transmission and distribution to transmit electrical energy across large distances
the overhead systems and underground systems of the main systems to electric
power transmitted

18. A 4 pole Alternator runs in 750 rpm, what is the frequency?

50 HZ

25Hz

60Hz

None of the above


Correct Answer : b

Explanation : F = Ns x P / 120 = 750 x 4 / 120 = 25 Hz

19. The electric flux passing out through a closed surface is equal to:

The line integral of the surface


Zero

The flux density at the surface

The total charge enclosed by the surface


Correct Answer : d

Explanation : The total of the electric flux out of a closed surface is equal to the
charge enclosed divided by the permittivity. The electric flux through an area is
defined as the electric field multiplied by the area of the surface projected in a
plane perpendicular to the field.

20. The initial investment for a project is 2.0 million QR. A net annual profit of
150,000 QR is anticipated. Using a 10% desired rate of return on the
investment that is the payback period for the project?

6.84 Years

4.55 Years

5.36 Years

8.89 Years
Correct Answer : d

21. The voltage gain of an amplifier with 9% negative feedback is 10. The
voltage gain without feedback will be:

1.25

100

90
Correct Answer : c
Explanation :

22. What is the role of the Zener diode?

Rectification

Voltage regulation

Amplification

Square wave Generation


Correct Answer : b:

Explanation : The Zener Diode is used in its “reverse bias” or reverse breakdown
mode, i.e. the diodes anode connects to the negative supply. A Zener diode will
continue to regulate its voltage until the diodes holding current falls below the
minimum IZ(min) value in the reverse breakdown region.

23. For an op-amp having differential gain Av and common-mode gain Ac the
CMRR is given by

Av + Ac

Av / Ac

1 + Av / Ac)

Ac / Av
Correct Answer : b

Explanation : CMRR = differential mode gain/ Common mode gain

24.……….is a closed loop system.


Auto-pilot for an aircraft

Direct current generator

Car starter

Electric switch
Correct Answer : a

Explanation : An autopilot is a system used to control the trajectory of an aircraft,


marine craft or spacecraft without requiring constant manual control by a human
operator. Autopilot does not replace human operators. Instead, autopilot assists the
operator's control of the vehicle, allowing the operator to focus on broader aspects
of operations.

25. An item on a project network is Design Software Completed. This is best


described as a(n)

Event

Path

Activity

Milestone
Correct Answer : a

Explanation : Event is a term used to represent a point in time when an activity is


started or completed. It does not consume time.

26. The full form of PERT is ___________?

Program Evaluation and Rate Technology

Program Evaluation and Robot Technique

Program Evaluation and Robot Technology

Program Evaluation and Review Technique


Correct Answer : d

Explanation : There are various network techniques that are called by various
names like PERT, CPM, TOPS and LESS. Network technique is one of the major
advancements in management science. The full form of PERT is Program Evaluation
and Review Technique.

27. An over-excited synchronous motor takes

leading current

lagging current

both (a) and (b)

none of the above


Correct Answer : a

Explanation : An over-excited synchronous motor takes always leading current.

You might also like