Tutorial on Tails Stock

Shivaramakrishna A
Dept of Mechanical Engineering
Ballari Institute of Technology and Management
Bellary-583104

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 1
 PART 1: BODY
STEP 1: Protrusion
Sketch on YZ plane or right plane as shown in fig
Symmetric protrude distance 312 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 2
 STEP 2: Cutout
Sketch on XZ plane or front plane as shown in fig
cutout depth mm 150 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 3
 STEP 3: Cutout
Sketch on YZ plane or right plane as shown in fig
cutout depth up to next surface

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 4
 STEP 4: Cutout
Sketch on YZ plane or right plane as shown in fig
cutout depth up to next surface

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 5
 STEP 5: Cutout
Sketch on XZ plane or front plane as shown in fig
cutout depth through all

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 6
 STEP 6: Cutout
Sketch on XZ plane or front plane as shown in fig
cutout depth through all

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 7
 STEP 7: Revolved Protrusion
Sketch on XZ plane or front plane as shown in fig
revolve protrusion angle 3600

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 8
 STEP 8: Protrusion
Sketch on XY plane or Top plane as shown in fig
Symmetric protrusion distance 70 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 9
 STEP 9: Cutout
Sketch on YZ plane or front plane as shown in fig
cutout depth 70 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 10
 STEP 10: Hole
Hole 1 of diameter 38 mm through all
Hole 2 of diameter 22 mm depth 35 mm
Hole 3 of diameter 8 mm, 4 holes depth 15 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 11
 PART 3:BARREL
Sketch on XZ plane or front plane as shown in fig
Use revolve protrusion angle 360o
cutout dimension 4.5 x 3 mm length 245 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 12
 PART 4:SCREW SPINDLE
Sketch on XZ plane or front plane as shown in fig
Use revolve protrusion angle 360o

cut out 4.5 x2.25 and 28 mm length

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 13
 PART13 handle
Sketch on XZ plane or front plane as shown in fig
Use revolve protrusion angle 360o
sketch on XY or top plane as shown

Symmetric protrusion distance 40 mm

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 14
 PART19 CENTRE
Sketch on XZ plane or front plane as shown in fig
Use revolve protrusion angle 360o

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 15
 PART 8 HAND WHEEL
Step 1:
Sketch on XZ plane or front plane as shown in fig
Use revolve protrusion angle 360o

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 16
 PART 8 HAND WHEEL
Step 2:
Sketch on XZ plane or front plane as shown in fig
Use revolve protrusion angle 360o

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 17
 PART 8 HAND WHEEL
Step 3:
Sketch on YZ plane or right plane as shown in fig
Use lofted protrusion

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 18
 PART 8 HAND WHEEL
Step 4:
circular pattern according to the requirement

Shivaramakrishna A,
Assistance Professor
14-3-2014 BITM, Bellary-583104 19