T238 Digital Trigger Unit V1.

42
(With overheat protection & auto-loading)
Warning:
This upgrade kit is designed for professional AIRSOFT/gel
ball blaster player who can fully disassemble and assemble
Automatic Electric Gun. The compatibility with all Gearboxes is
not guaranteed, but it can fit into standard or common brand
Gearboxes V2 without larger modification. Related Tools and
skills is needed for installing the product.

Attention:
1. Protect the detection switch while installing, do not pull the
trigger before finishing installation in case that the trigger
breaks the detection switch.
2. Mind the positive and negative of the motor, do not reverse.
3. Gearbox, motor and grip is not functional before finishing
installation. Please finish the installation at first.
Description:
T238 digital trigger unit is a programmable MOSFET
which is specially designed for AIRSOFT and gel ball version
Gearbox V2. With high speed processor and 2 high power
MOSFET chips, this system has many individualized
programmable functions, such as piston positioning, binary
trigger, multiple-shot and so on. Besides, it also has the
functions of battery low-voltage protection and gearbox
block-up protection. It can effectively improve the stability,
shooting speed and response speed of gearbox, at the same
time, it can completely eliminate the problem of gearbox
single-shot become multiple-shot. The module uses a
maximum of 14.8V batteries. Soldering and wiring are
required.
Main parameters:
 Size: 45*30*14mm
 Operating voltage: 7.4-14.8V
 Active break tech & Piston reset
 Programmable auto-loading function
 Multiple programmable shooting mode
 Overheat protection
 Maximum Inrush current is 240A, Maximum Brake current is
100A
 Compatible with various Standard Gearbox V2
Functions:
1. Low battery voltage protection, the default setting is
7.4V battery. Change the battery when hearing ‘beep
beep beep beep’ 4 times low voltage warning sound.
2. Block-up protection. When gearbox Block-up occurs,
the system stops working and emits an elongated
‘beep’ sound. Please check the wave box immediately
by power off.
3. Auto-loading function is designed for gel ball blaster
magazines with motor inside, when changing the
magazine, the magazine motor will run automatically
for a period of time, and the length of time can be
programmed by 9th option.
4. This module is able to increase rate of fire, the stability
of single-shot and make batteries have higher
durability.
5. The energy that support the active brake function
comes from the inertia of motor, stop the piston
 without delay. The effect of active brake is significant
on high torque motor
6. The active function prevents the over-spin of gears, this
solve the issue that the single shot becomes multiple
shot under high voltage. Meanwhile, the spring is fully
released in semi-auto mode and parts in gearbox are
not under strain, increase the life cycle of gearbox and
parts.
7. The system includes multiple shooting mode, these
modes can be selected by fire select switch
8. The default position of the piston is adjustable in
semi-auto mode. Pre-cocking function can be
implementing, zero trigger delay
9. Adjustable rate of fire, the gap between two single
shots can be programmable, to achieve adjustable
rate of fire
10. When the DTU is overheated, after the trigger is
pulled, the motor will give a beep prompt until it is
automatically restarted after cooling.
Modes:
SAFE：This mode is completely the same as original safe mode.
The trigger is stopped by Safety lever
SEMI: This mode can be programmed to implementing
semi-auto, double stroke single shot, 3-round burst to
6-round burst, the default mode is semi auto
AUTO: This mode can be programmed to implementing
full-auto, 3-round burst, 6-round burst and 9-round
burst, the default mode is Full-auto

Requirements:
1. Silver plate wire is needed for this system, power wire for
motor and battery should be larger than 0.5sqm silver plate
wire, wire for electronic powered magazine should be
around 0.25sqm.
2. High-power soldering iron (higher than 50W) is
recommended, solder the clop with 0.5sqm soldering wire
 and soldering rosin. Please ask professional for help if you
do not know to solder.
3. Please use Spring smaller than M150.
4. Use high torque motor can stop the motor faster and prevent
DTU from overheating .
5. In standby state, the current of the system is smaller than
0.01A. Please disconnect the battery if it is not used for a
long time.
Installation:
1. Measure the length of each wire according to the wiring
diagram then solder the wires on the clip (The exposed
solder joint on the PCB clip is not stand too much force, do
not pull the wire after the wire is soldered in case damaging
the clip)
2. Disassemble the gearbox, it is necessary to take off the
cut-off lever, keep the Safety lever and selector plate on the
gearbox (Tutorial for disassemble gearbox can be found on
YouTube)
3. Install the module and push the wires in the gearbox (some
gearbox needs to be cut off stiffener or drilled hole)
4. Assemble the gearbox
5. For more details, scan the QR code
Quick Test:
After soldering, connect the motor. Make sure the wires are
connected correctly, then press the trigger button ‘S2’ and
connect the battery to it. After the battery is connected, release
the trigger button ‘S2’, the the module will run into Quick Test
mode. Press each button one by one, you will get two ‘beep’s, if
not, your module is not right, contact the customer service
immediately.
Programming:
1. Disconnect the battery, then set the fire selector switch to
auto.
2. Connect the battery and pull the trigger in 3 seconds, After
hearing 2 long ‘beep~’ , the module runs into
programmable mode, otherwise it will be in auto mode.
3. In the programmable mode, the motor emits short ‘beep’,
the numbers of ‘beep’ means the serial number of the
option. If you want to choose the option, pull and hold the
trigger in 2 seconds after ‘beep’s till a long ‘beep’, the
module will be set to matched option. (The options and
matched function/parameter are in the table below).
4. After setting to the selected option, the motor emits short
‘beep’s, the number of ‘beep’s means the different
function/parameter of this option. If you want to program to
set it to certain option or parameter, pull and hold the
trigger in 2 second after ‘beep’ till 2 long ‘beep’, then the
module is in programmable mode again.
Option\Parameter 1 2 3 4 5 6

1 Low Battery 7.4V 11.1V 14.8V 9.6V OFF RESET

Warning

2 Semi-auto mode Semi Binary 3 round 4 round 5 round 6 round

trigger bursts bursts bursts bursts

3 Full-auto mode Auto Semi 3 round 4 round 5 round 6 round

bursts bursts bursts bursts

4 Pre-cocking 1：The most front position, 2~15：The larger the parameter is the further back

control the piston is. The certain position is related the strength of the spring.

5 Firing interval OFF 0.3s 0.6s 0.9s 1.2s 1.5s

6 Rate of fire 100% 80% 70% 60% 50%

7 Trigger mode Normal Sensitive AUG Mode：Light press semi-auto and heavy press

(V1.5+ only) auto

8 Selector type G36 AK47

9 Auto-loading 3S 2.5S 2S 1.5S 1S 0.5S OFF

(for gel ball only)