X-Sense SCO1_SC02_SCO7_SC08 - Smoke and Carbon Monoxide Alarm Manual _ ManualsLib

12/9/24, 5:30 PM X-Sense SCO1/SC02/SCO7/SC08 - Smoke and Carbon Monoxide Alarm Manual | ManualsLib
X-Sense SCO1/SC02/SCO7/SC08 - Smoke and

Carbon Monoxide Alarm Manual
https://www.manualslib.com/manual/3195688/X-Sense-Sco1.html 1/21
Contents
1. Package Contents
2. lntroduction
3. Technical Specifications
4. Product Overview
4.1. Test & Silence Button
4.2. Alarm Sounder
4.3. LED lndicator
4.4. Low Battery
4.5. End of Life
4.6. LCD Display
5. Fire SafetyTips
6. Basic Safety lnformation
7. lnstallation lnstructions
8. Recommended Placement
9. How to lnstall This Alarm
10. Locations to Avoid
11. Mounting Steps
12. Deactivation of the Alarm
13. Weekly Test
14. Maintenance
15. lf the Smoke Alarm Sounds
16. lf the СО Alarm Sounds
17. What You Need to Know About СО
18. Documents / Resources
18.1. Download manual
Package Contents
1 х Alarm Unit
1 х Mounting Bracket
3 х Screws
3 х Anchor Plugs
1 х User Manual
1 х Warranty Card
2 х Carbon Monoxide Safety Stickers
lntroduction
AII X-Sense combination smoke & carbon monoxide alarms conform with regulatory
requirements, including UL 217 & UL 2034 standards and are designed to detect both smoke
and carbon monoxide.
This unit adopts photoelectric technology to detect smoke which is generally more sensitive
than ionization technology. lt is effective at detecting large particles, which tend to bе produced
in greater amounts bу smoldering fires and may smolder for hours before bursting into flame.
Sources of these fires may include cigarettes burning in couches or bedding.
Carbon monoxide (СО) is odorless, tasteless and invisible - it's а silent killer. Using
electrochemical sensing technology, this unit can detect increased levels of carbon monoxide
early, protecting your family from the dangers of carbon monoxide.
Note: For maximum protection, use smoke & СО alarms оп each level and in every
bedroom of your home.
THIS EQUIPMENT SHOULD ВЕ INSTALLED IN ACCORDANCE WITH ТНЕ NATIONAL

FIRE PROTECТION ASSOCIATION'S STANDARD 72
(National Fire Protection Association, Batterymarch Park, Quincy, МАО2269).
NEVER IGNORE ТНЕ SOUND OF ТНЕ ALARM!

Determining what type of alarm has sounded is easy with your X-Sense combination smoke &
carbon monoxide alarms. The alarm sounder will inform you of the type of situation occurring.
When the Smoke Alarm Sounds:

Smoke alarms are designed to minimize false alarms. Cigarette smoke will not normally set off
the alarm, unless the smoke is Ыown directly into the alarm.
This unit contains nuisance alarm protection, which will reduce the impact of cooking particles.
However, large quantities of combustiЬle particles from spills or broiling could still cause the
unit to alarm. Careful location of the unit away from the kitchen area will give the maximum
nuisance alarm protection.
Combustion particles from cooking may set off the alarm if located too close to the cooking
area. Large quantities of combustiЫe particles are generated from spills or when broiling.
Using the fan on а range hood which vents to the outside (non-recirculating type) will also help
remove these combustiЬle products from the kitchen. lf the alarm sounds, check for nres nrst.
lf а nre is discovered, follow these steps. Become thoroughly familiar with these items, and
review with all family members!
*Alert small children in the home. Children sleep very sound and may not bе awakened bу the
sound of the smoke alarms.
*Leave immediately using one of your planned escape routes. Every second counts, so don't
stop to get dressed or pick up valuaЫes.
*Before opening inside doors, look for smoke seeping in around the edges, and feel with the
back of your hand. lf the door is hot, use your second exit. lf you feel it's safe, open the door
very slowly and bе prepared to close immediately if smoke and heat rush in.
*lf the escape route requires you to go through smoke, crawl low under the smoke where the
air is clearer.
*Go to your predetermined meeting place. When two people have arrived, one should leave to
call 911 from а neighbor's home, and the other should stay to perform а head count.
*Do not reenter under any circumstance until fire officials give the go-ahead.
*There are situations where а smoke alarm may not bе effective to protect against fire as
noted bу the NFPA and UL Std. 217. For instance:
Smoking in bed.
Leaving children unsupervised.
Cleaning with flammable liquids, such as gasoline.
Fires where the victim is intimate with а flaming initiated fire; for example, when а person's
clothes catch fire while cooking.
Fires where the smoke is prevented from reaching the detector due to а closed door or
other obstruction.
lncendiary fires where the fire grows so rapidly that an occupant's egress is blocked even
with properly located detectors.
Actuation of your CO Alarm indicates the presence of Carbon Monoxide (CO) which can
kill you.
When the Carbon Monoxide Alarm Sounds:
1. Operate the test/reset button.
2. Call your emergency services (Fire Dept. or 911).
3. lmmediately move to fresh air - outdoors or bу an open door/window. Do а head count to

check that all persons are accounted for. Do not reenter the premises nor move away from
the open door/window until the emergency services responders have arrived, the
premises has been aired out, and your alarm remains in its normal condition.
4. After following steps 1-3, if your alarm reactivates within а 24-hour period, repeat steps 1-
3 and call а qualified appliance technician to investigate for sources of СО from fuel-
burning equipment and appliances, and inspect for proper operation of this equipment. lf
proЫems are identified during this inspection, have the equipment serviced immediately.
Note any combustion equipment not inspected bу the technician and consult the
manufacturer's instructions, or contact the manufacturer directly, for more information
about СО safety and this equipment. Make sure that motor vehicles are not, and have not
been, operating in an attached garage or adjacent to the residence.
Technical Specifications
Power supply 10-year sealed lithium battery

Smoke: Photoelectric
Sensor type
СО: Electrochemical
Product life About 10 years
Safety standards Conforms with UL 217 & UL 2034 standards
Smoke sensitivity 0.97-1.79%/ft OBS
70 ppm: 60-240 minutes
СО sensitivity 150 ppm: 10-50 minutes
400 ppm: 4-15 minutes
Standby current < 6 µА (avg.)

Alarm current < 60 mA (avg.)
Best operating amЬient temperature 40-100°F (4.4-37.8 °С)
Operating relative humidity < 85% RH (non-condensing)
Alarm loudness > 85 dB at 9.84 ft (3 m)@ 3.2 + 0.3 kHz pulsing alarm
Silence duration Smoke: < 9 minutes; СО: < 6 minutes
Product Overview
THIS SMOKE AND CO ALARM IS DESIGNED FOR INDOOR USE ONLY. DO NOT EXPOSE
TO RAIN OR MOISTURE. DO NOT KNOCK OR DROP THE ALARM. DO NOT OPEN OR
TAMPER WITH THE ALARM AS THIS COULD CAUSE MALFUNCTION.
Test & Silence Button
The Test & Silence button is used to test the unit's electronics and to silence the unit during an
alarm. When testing the alarm weekly, you should first wake up your alarm bу pressing the
test button; once the alarm has woken up, the LCD display will activate, then press the test
button again until you hear а short bеер, indicating that the alarm has entered the test mode.
То save power, the alarm is designed to automatically turn off the LCD display if there has
been no operation for 5 minutes.
Note: After а test has begun, the alarm will sound and the red LED will flash. This does
not indicate that smoke/CO is present.
lf you press the test button during an alarm state, the unit will enter the silence mode.
СО silence mode: press the test button during an alarm state, the unit will enter the silence
mode. lf the СО density still exceeds the alarm threshold within 6 minutes, the unit will enter
another alarm state. Otherwise, the unit will exit from silence mode after 9 minutes.
Note: lf the smoke or СО concentration has reached an alarm level, silence mode
cannot bе enaЫed. This unit will continue to alarm until the smoke or СО concentration
has decreased to а low level.
Alarm Sounder
The alarm will sound when there is smoke or СО present, when testing the alarm, and when
there is а fault.
LED lndicator
The LED indicator will flash in conjunction with the alarm sounder. Therefore, it will flash
during the following states: when powering on, in standby mode, during smoke or СО alarm
states, when exiting an alarm state, during test mode, when there is low battery, in silence
mode, when there is а fault and when the unit is at the end of its life.
Low Battery
The LED indicator will flash yellow together with one bеер every 60 seconds.
ТНЕ UNIT MUST ВЕ DEACTIVATED (see "Deactivation of the Alarm" section) AND
REPLACED AS SOON AS POSSIBLE.
(lf you press the test button when there is low battery, the low battery signal will temporarily
cease for 10 hours; if you press the test button again, the unit will enter the test mode and
then the standby mode.)
End of Life
Once the maximum lifetime (10 years) is reached, the alarm delivers 2 beeps and the LED
indicator will flash yellow twice every 30 seconds. This end-of-life signal can bе temporarily
silenced for 3 days bу pressing the test button.
The end-of-life silence feature can only bе used for а total of 30 days. After 30 days, the end-
of-life signal cannot bе silenced.
Different working modes and states are shown in the below tаЫе:
Mode LED lndicator AudiЫe Alarm Remarks

Blinks 8 cycles
Powering
(red/green/yellow) in None.
on
sequence.
Standby Flashes green once every
None.
mode 60 seconds.
Flashes red 3 times every 3 long beeps every
Smoke alarm.
1.5 seconds. 1.5 seconds.
First 4 minutes: flashes First 4 minutes: 4

red 4 times every 5.8 quick beeps every
seconds. 5.8 seconds.
СО alarm.
Alarm
After 4 minutes: flashes After 4 minutes: 4
mode
red 4 times every 60 quick beeps every
seconds. 60 seconds.
Exiting an alarm: When the

Flashes green once every smoke or СО concentration drops
None.
second for 5 seconds. below the alarm threshold, the
alarm signal stops.
2 sets of 3 long
2 sets of 3 red flashes
beeps followed bу
Test mode followed bу 2 sets of 4
2 sets of 4 quick
red flashes.
beeps.
Flashes red once every 5 After 9 minutes, the unit will exit
Silence None.
seconds. silence mode.
mode
Flashes green 3 times. None. Exiting silence mode.
Low Flashes yellow once One bеер every 60
battery every 60 seconds. seconds.
Flashes yellow 1 or 2
Smoke malfunction mode.
times every 40 seconds. 2 beeps every 40
Fault
Flashes yellow 3 or 4 seconds.
СО malfunction mode.
times every 40 seconds.
Flashes yellow 2 times 2 beeps every 30
End of life
every 30 seconds. seconds.
LCD Display
While detecting СО, the LCD will display different indications to help you understand what to
do, as shown below:
LCD Alarm
LED Status Unit Status Solutions
Display Sound
If a CO concentration
of 30-999 ppm exists
The alarm
for a certain time
delivers
period, the screen will
beeps and Dangerous CO
be backlit blue, and Refer to "If the
the LED concentration
the LED indicator will Smoke/CO Alarm
indicator will has been
flash red 4 times Sounds"
flash with the detected
every 58 seconds.
same
After 4 minutes, it will
frequency.
flash red 4 times per
minute.
Check if there аre any
sources of СО gas,
such as from burning,
СО has been
lf a СО concentration cooking, etc. lf such
detected, but
of 30-999 ppm exists gas sources exist,
has not reached
for а very short time, please cut them off as
No sound. alarm status.
the LED indicator will soon as possiЬle.
Potential
flash green once Open the doors and
dangerous
every 60 seconds. windows to ventilate
conditions exist.
the room and
immediately move to
fresh air.
Тhе alarm
delivers
The LED indicator The unit is self-
bеерs and
flashes red 3 times checking
the LED
for 2 cycles and then (the test button None.
indicator will
4 times for 2 cycles, has been
flash with the
finally flashing once. pressed).
same
frequency.
Тhе LED indicator
The unit has
flashes red, green One short
been powered None.
and yellow in bеер.
on.
sequence.
The unit is
The LED indicator
working normally
flashes green once None. None
with good
every 60 seconds.
battery life.
The LCD display
alternates between
As the battery is not
"Lb" and current СО One quick
Low battery replaceable, you will
level. The LED bеер every
warning. need to replace the
indicator flashes 60 seconds.
unit.
yellow once every 60
seconds.
Тhе LED indicator
Smoke
flashes yellow 1 time
malfunction.
every 40 seconds.
Тhе LED indicator
flashes yellow 2 Smoke
times every 40 malfunction. lf "Err" continues to
seconds. Two quick display, the unit has
Тhе LED indicator beeps every malfunctioned and
flashes yellow 3 40 seconds. must bе replaced
СО malfunction.
times every 40 immediately.
seconds.
Тhе LED indicator
flashes yellow 4
СО malfunction.
times every 40
seconds.
ТheLED indicator Тwo quick

Replace the unit
flashes yellow twice beeps every End of life.
immediately.
every З0 seconds. 30 seconds.
Fire SafetyTips
Follow these safety rules to prevent hazardous situations:
1. Use smoking materials properly. Never smoke in bed.
2. Кеер matches or lighters away from children.
3. Store flammable materials in proper containers.
4. Кеер electrical appliances in good condition and don't overload electrical circuits.
5. Кеер stoves, barbecue grills, fireplaces and chimneys grease-free and debris-free.
6. Never leave anything cooking on the stove unattended.
7. Кеер portable heaters and open flames, like candles, away from flammable materials.
8. Don't let rubbish accumulate.
9. Кеер alarms clean, and test them weekly.
10. Replace alarms immediately if they are not working properly. Smoke alarm that do not
work cannot alert you to а fire.
11. Кеер at least one working fire extinguisher on every floor, and an additional one in the
kitchen.
12. Have fire escape ladders or other reliaЫe means of escape from an upper floor in case
stairs are blocked.
Basic Safety lnformation
1. DANGERS, WARNINGS, AND CAUTIONS ALERT YOU TO IMPORTANT OPERATING

INSTRUCTIONS OR TO POTENTIALLY HAZARDOUS SITUATIONS. PAY SPECIAL
ATTENTION TO THESE SITUATIONS.
2. THIS COMBINATION SMOKE & CARBON MONOXIDE ALARM IS ONLY APPROVED

FOR HOME USE.
3. THIS CARBON MONOXIDE ALARM IS DESIGNED TO DETECT CARBON MONOXIDE

FROM ANY SOURCE OF COMBUSTION.
4. CONSTANT EXPOSURES TO HIGH OR LOW HUMIDITY MAY REDUCE BATTERY

LIFE.
5. SMOKE ALARMS ARE NOT TO BE USED WITH DETECTOR GUARDS UNLESS THE
COMBINATION HAS BEEN EVALUATED AND FOUND SUITABLE FOR THAT
PURPOSE.
THIS SMOKE & CARBON MONOXIDE ALARM HAS TWO SEPARATE ALARMS WHICH
WORK INDEPENDENTLY. THE CARBON MONOXIDE ALARM IS NOT DESIGNED TO
DETECT FIRE OR ANY OTHER GAS. IT WILL ONLY INDICATE THE PRESENCE OF
CARBON MONOXIDE GAS AT THE SENSOR. CARBON MONOXIDE GAS MAY BE
PRESENT IN OTHER AREAS. THE SMOKE ALARM WILL ONLY INDICATE THE
PRESENCE OF SMOKE THAT REACHES THE SENSOR. THE SMOKE ALARM IS NOT
DESIGNED TO DETECT GAS, HEAT OR FLAMES.
1. NEVER IGNORE ANY ALARM. FAILURE TO RESPOND CAN RESULT IN SERIOUS

INJURY OR DEATH.
2. THE SILENCE FEATURE IS ONLY FOR YOUR CONVENIENCE AND WILL NOT
CORRECT A PROBLEM. ALWAYS CHECK YOUR HOME FOR A POTENTIAL PROBLEM
AFTER ANY ALARM. FAILURE TO DO SO CAN RESULT IN INJURY OR DEATH.
3. TEST THIS SMOKE/CO ALARM ONCE A WEEK. IF THE ALARM EVER FAILS TO TEST
CORRECTLY, REPLACE IT IMMEDIATELY! IF THE ALARM CANNOT WORK
PROPERLY, IT WILL NOT ALERT YOU TO A PROBLEM.
4. THIS PRODUCT IS INTENDED FOR USE IN ORDINARY INDOOR LOCATIONS OF

FAMILY LIVING UNITS. IT IS NOT DESIGNED TO MEASURE CO LEVELS IN
COMPLIANCE WITH OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
(OSHA) COMMERCIAL OR INDUSTRIAL STANDARDS. INDIVIDUALS WITH MEDICAL

CONDITIONS THAT MAY MAKE THEM MORE SENSITIVE TO CARBON MONOXIDE
MAY CONSIDER USING WARNING DEVICES WHICH PROVIDE AUDIBLE AND VISUAL
SIGNALS FOR CARBON MONOXIDE CONCENTRATIONS UNDER 30 PPM. FOR
ADDITIONAL INFORMATION ON CARBON MONOXIDE AND YOUR MEDICAL
CONDITION CONTACT YOUR PHYSICIAN.
5. THE REPLACEMENT DATE THAT APPEARS ON THE DEVICE IS THE DATE BEYOND
WHICH THE DEVICE MAY NO LONGER DETECT CARBON MONOXIDE ACCURATELY
AND SHOULD BE IMMEDIATELY REPLACED.
6. THIS DEVICE IS DESIGNED TO PROTECT INDIVIDUALS FROM THE ACUTE

EFFECTS OF CARBON MONOXIDE EXPOSURE. IT MAY NOT FULLY SAFEGUARD
INDIVIDUALS WITH SPECIFIC MEDICAL CONDITIONS. IF IN DOUBT, CONSULT A
MEDICAL PRACTITIONER.
lnstallation lnstructions
1. Prioritize the installation of an alarm in the bedroom and walkways, and make sure you
can hear the alarm from all sleeping areas. ln а home with several bedrooms, install an
alarm in every bedroom. lf you install only one smoke alarm in your home, install the alarm
near to all bedrooms where possiЬle, and not in а basement or furnace room.
2. lnstall an alarm above the stairway and on every floor of the house.
3. Smoke, heat and anything burning will spread horizontally after rising to the ceiling, so
install the alarm in the middle of the ceiling where possiЬle. Ensure the alarm is within
working distance of all corners of the room.
4. lf an alarm cannot bе installed in the middle of а ceiling, install at а distance of 20 inches

(50 cm) away from the corners of the room.
5. lf an alarm is installed on а wall, it should bе at а distance of 4-12 inches (10-30 cm)

below the ceiling.
6. lf the length of а room or hall is beyond 30 feet (900 cm), you will need to install several
alarms in the same space.
lnstallation lnstructions - Step 1
7. When the wall or ceiling is angled, the alarm needs to bе installed within 3 feet (90 cm) of
the highest wall or ceiling point (measured horizontally) in the room.
lnstallation lnstructions - Step 2
Recommended Placement
1. THIS ALARM SHOULD ВЕ INSTALLED ВУ А COMPETENT PERSON.
2. INSTALLATION OFTHE ALARM SHOULD NOT ВЕ USED AS А SUBSTITUTE FOR

PROPER INSTALLATION, USE AND MAINTENANCE OF FUEL BURNING APPLIANCES
INCLUDING APPROPRIATE VENTILATION AND EXHAUST SYSTEMS.
FIRE EXTINGUISHERS
SMOKE ALARMS
CARBON MONOXIDE ALARMS
SMOKE & СО ALARMS
Note: Kitchens should bе installed with smoke alarms which have the silence mode.
How to lnstall This Alarm
THIS COMBINATION SMOKE/CO ALARM IS DESIGNED TO ВЕ MOUNTED ON ТНЕ

CEILING OR WALL.
FAILURE ТО PROPERLY INSTALL AND ACTIVATE THIS ALARM WILL PREVENT

PROPER OPERATION OF ТНЕ ALARM AND WILL PREVENT ITS RESPONSE ТО FIRE
HAZARDS OR СО.
Locations to Avoid
This product is intended for use in ordinary indoor locations of family living units. lt is not
designed to measure compliance with the Occupational Safety and Health Administration
(OSHA) commercial or industrial standards.
1. Do not install in garages, kitchens, furnace rooms or bathrooms! Do not install within 5 ft
or 1.5 m of cooking appliances.
2. Do not install within 3 ft (0.9 m) of the following: The door to а kitchen, or а bathroom that
contains а tub or shower, forced air supply ducts used for heating or cooling, ceiling or
whole house ventilating fans, or other high air flow areas. Avoid excessively dusty, dirty or
greasy areas. Dust, grease or household chemicals can contaminate the alarm's sensors,
causing the alarm to not operate properly.
3. Place the alarm where drapes or other objects will not blосk the sensors. Smoke and СО
must be аblе to reach the sensors to accurately detect these conditions. Do not install in
peaks of vaulted ceilings, "А" frame ceilings or gabled roofs. Кеер out of damp and humid
areas.
4. lnstall at least one (1) foot away from fluorescent lights, as electronic noise may cause
nuisance alarms. Do not place in direct sunlight and keep out of insect-infested areas.
Extreme temperatures will affect the sensitivity of the smoke/CO alarm. Do not install in
areas where the temperature is colder than 40°F (4.4 °С) or hotter than 100°F (37.8 °С),
such as garages and unfinished attics. Do not install in areas where the relative humidity
(RH) is above 85%. Place away from doors and windows that open to the outside.
5. Smoke alarms are not to be used with detector guards unless the combination (alarm and
guard) has been evaluated and found suitable for that purpose.
Mounting Steps
Mounting Steps
1. Drill three 6.0 mm holes in the wall or ceiling, then insert three plastic anchor plugs into
the holes with а hammer.
2. Attach the mounting bracket to the surface of the wall or ceiling with three screws and
mount the alarm into the bracket by pushing them together and twisting the unit clockwise.
3. Test the unit by using the Test/Silence button. Ensure the unit sounds in an alarm pattern.
Note: This model is equipped with а feature that automatically activates the alarm when
the alarm is attached to the mounting bracket for the first time.
Deactivation of the Alarm
1. DO NOT DEACTIVATE THE ALARM UNIT UNTIL THE END-OF-LIFE SIGNAL HAS BEEN
HEARD.
2. ONCE THE MAXIMUM LIFETIME (10 YEARS) IS REACHED, THE ALARM DELIVERS 2
BEEPS EVERY 30 SECONDS.
3. ONCE THE ALARM IS DEACTIVATED, IT WILL NO LONGER FUNCTION. IT CANNOT

BE REACTIVATED AND MUST BE REPLACED.
То Deactivate the Alarm

Pressing the Test/Silence button can silence the end-of-life signal for up to 3 days.
1. Peel back the shaded label obstructing the "DIS" setting, and break the thin plastic guard,
as below.
2. Twist the plastic pin upwards to the "DIS" position or insert а screwdriver into the slot and
turn the dial clockwise to the "DIS" position.
3. Dispose of the alarm.
4. Replace the alarm.

Deactivation of the Alarm
Weekly Test
1. NEVER USE AN OPEN FLAME OF ANY KIND ТО TESTTHIS UNIT. YOU MIGHT
ACCIDENTALLY DAMAGE OR SET FIRE TO THE UNIT OR TO YOUR НОМЕ.
2. NEVER USE А VEHICLE EXHAUST TO TEST THIS UNIT. EXHAUST FUMES МАУ
CAUSE PERMANENT DAMAGE AND VOID YOUR WARRANTY.
3. DO NOT STAND CLOSE ТО ТНЕ ALARM WHEN ТНЕ ALARM IS SOUNDING.

EXPOSURE АТ CLOSE RANGE МАУ ВЕ HARMFUL ТО YOUR HEARING. WHEN
TESTING, STEP AWAY WHEN ТНЕ ALARM BEGINS ТО SOUND.
Maintenance
То keep your smoke/CO alarm in good working order, follow these simple steps:
1. Verify the unit's alarm sound and indicators are working properly by testing the unit once а
week.
2. Remove the unit from the ceiling/wall and clean the alarm cover and vents with а soft
brush attachment once а month to remove dust and dirt.
3. Never use detergents or other solvents to clean the unit.
4. Avoid spraying air fresheners, hair spray or other aerosols near the alarm.
5. Do not paint the unit. Paint will seal the vents and interfere with the sensor's aЬility to
detect smoke or СО. Never attempt to disassemble the unit or clean inside. Doing so will
void your warranty.
6. When removed, place the smoke/CO alarm back in its proper location as soon as
possible, to assure continuous protection from fire or carbon monoxide poisoning.
7. When household cleaning supplies or similar contaminants are used, the area should be
ventilated.
lf the Smoke Alarm Sounds
1. Don't panic; stay calm. Follow your family's escape plan.
2. Get out of the house as quickly as possible. Don't stop to get dressed or collect anything.
3. Feel doors with the back of your hand before opening them.
4. lf а door is cool, open it slowly. Don't open а hot door. Кеер doors and windows closed,
unless you must escape through them.
5. Cover your nose and mouth with а cloth (preferably damp).
6. Take short, shallow breaths.
7. Meet at your planned meeting place outside your home, and do а head count to make
sure everybody got out safely.
8. Call the Fire Department as soon as possible from outside. Give your address, then your
name.
9. Never go back inside а burning building for any reason.
10. Contact your Fire Department for ideas on making your home safer.
lf the СО Alarm Sounds
1. Кеер calm and immediately move to fresh air. Open all doors and windows to increase the
rate of ventilation. Stop using all fuel-burning appliances and ensure, if possible, that they
are turned off, e.g. for gas appliances, isolate the emergency control valve.
2. lf the alarm continues to be activated, then evacuate the premises. Leave the doors and
windows open, and only re-enter the building when the alarm has stopped. ln multi-
occupancy and multi-storey premises, ensure that all the occupants are alerted to the risk.
3. Get medical help for anyone suffering the effects of carbon monoxide poisoning, and
advise that carbon monoxide inhalation is suspected.
4. Telephone the appropriate appliance servicing and/or maintenance agency or, when
necessary, the relevant fuel supplier on their emergency number or the national Gas
Emergency Service Provider, if appropriate, so that the source of carbon monoxide
emissions can be identified and corrected. Unless the reason for the alarm is obviously
spurious, do not use the fuel-burning appliances again, until they have been checked and
cleared for use by а competent person according to national regulations.
What You Need to Know About СО
СО cannot be seen, smelled or tasted and can be fatal. The build-up of СО in the blооd is
called the carboxyhemoglobin (СОНЬ) level and interferes with the body's ability to supply
itself with oxygen. Depending on the concentration, СО can kill in minutes. The most common
sources of СО are malfunctioning gas appliance used for heating and cooking, vehicles
running in an attached garage, blocked chimneys or flues, portable fuel burning heaters,
fireplaces, fuel powered tools and operating а grill in an enclosed space.
lndications of carbon monoxide poisoning include symptoms similar to the flu, but with no
fever. Other symptoms include dizziness, fatigue, weakness, headache, nausea, vomiting,
sleepiness and confusion. Everyone is susceptiЬle to the danger of СО, but experts agree that
unborn babies, small children, pregnant women, senior citizens and people with heart or
respiratory problems are at the highest risk for serious injury or death. Every year а qualified
technician should inspect and clean your heating system, vents, chimney, and flues.
The following symptoms are related to carbon monoxide poisoning and should be discussed
with all members of the household:
Mild exposure: Slight headache, nausea, vomiting, fatigue (often described as "Flu-like"
symptoms).
Medium exposure: Severe throbbing headache, drowsiness, fast heart rate.
Extreme exposure: Unconsciousness, cardiorespiratory failure, death.
The above levels of exposure relate to healthy adults. Levels differ for those at high risk.
Exposure to high levels of carbon monoxide can be fatal or cause permanent damage and
disabilities. Many cases of reported carbon monoxide poisoning indicate that while victims are
aware they are not well, they become so disoriented they are unable to save themselves by
either exiting the building, or calling for assistance. Also, young children and household pets
may be the first affected. Familiarization with the effects of each level is important.
Documents / Resources
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information,
FCC rules, etc.
Download X-Sense SCO1/SC02/SCO7/SC08 - Smoke and Carbon Monoxide Alarm Manual
Need Assistance?
Do you have a question about the SCO1 that isn't answered in the manual? Leave your question here.
Your name
Your email
Your comment
Stay updated with the latest solutions
Submit your question
Related Manuals for x-sense SCO1
X- X-Sense XC01-WR - Wireless Interlinked Carbon Monoxide Carbon Monoxide Alarm x-sense SC07-WX Manual
Sense Alarm Manual Carbon Wi-fi combination smoke and carbon monoxide alarm (type b) (63
XC01- (article) Monoxide pages)
X- X-Sense XCO1/XCO1-R - Carbon Monoxide Alarm Manual Carbon Monoxide Alarm x-sense Link+ CO03D-W Manual
Sense (article) Carbon Wireless interlinked carbon monoxide alarm (20 pages)
XCO1/XC Monoxide
X- X-Sense CO03D - Carbon Monoxide Alarm Manual Carbon Monoxide Alarm x-sense XC01-WR Manual
Sense (article)
Carbon Wireless interlinked carbon monoxide alarm (23 pages)
CO03D - Monoxide
X- X-Sense XP04/XP05/XP06 - Monoxide Alarm with Battery Carbon Monoxide Alarm x-sense XC04-WX User Manual
Sense Backup Manual Carbon Wi-fi carbon monoxide alarm (type b) (92 pages)
XP04/XP0 (article) Monoxide
X- X-Sense XC04-WX - Wi-Fi Carbon Monoxide Alarm Manual Carbon Monoxide Alarm x-sense Pro XC01 User Manual
Sense (article)
Carbon Type b (17 pages)
XC04- Monoxide
Save Article as PDF

X-Sense SCO1_SC02_SCO7_SC08 - Smoke and Carbon Monoxide Alarm Manual _ ManualsLib

Uploaded by

Copyright:

Available Formats

X-Sense SCO1_SC02_SCO7_SC08 - Smoke and Carbon Monoxide Alarm Manual _ ManualsLib

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

X-Sense SCO1_SC02_SCO7_SC08 - Smoke and Carbon Monoxide Alarm Manual _ ManualsLib

Uploaded by

Copyright:

Available Formats

12/9/24, 5:30 PM X-Sense SCO1/SC02/SCO7/SC08 - Smoke and Carbon Monoxide Alarm Manual | ManualsLib

X-Sense SCO1/SC02/SCO7/SC08 - Smoke and

4.1. Test & Silence Button

4.2. Alarm Sounder

4.3. LED lndicator

4.4. Low Battery

4.5. End of Life

4.6. LCD Display

6. Basic Safety lnformation

9. How to lnstall This Alarm

10. Locations to Avoid

11. Mounting Steps

12. Deactivation of the Alarm

13. Weekly Test

15. lf the Smoke Alarm Sounds

16. lf the СО Alarm Sounds

17. What You Need to Know About СО

18. Documents / Resources

18.1. Download manual

2 х Carbon Monoxide Safety Stickers

THIS EQUIPMENT SHOULD ВЕ INSTALLED IN ACCORDANCE WITH ТНЕ NATIONAL

NEVER IGNORE ТНЕ SOUND OF ТНЕ ALARM!

When the Smoke Alarm Sounds:

Leaving children unsupervised.

Cleaning with flammable liquids, such as gasoline.

When the Carbon Monoxide Alarm Sounds:

1. Operate the test/reset button.

2. Call your emergency services (Fire Dept. or 911).

3. lmmediately move to fresh air - outdoors or bу an open door/window. Do а head count to

Power supply 10-year sealed lithium battery

Standby current < 6 µА (avg.)

Test & Silence Button

Mode LED lndicator AudiЫe Alarm Remarks

First 4 minutes: flashes First 4 minutes: 4

Exiting an alarm: When the

ТheLED indicator Тwo quick

Follow these safety rules to prevent hazardous situations:

1. Use smoking materials properly. Never smoke in bed.

2. Кеер matches or lighters away from children.

3. Store flammable materials in proper containers.

6. Never leave anything cooking on the stove unattended.

8. Don't let rubbish accumulate.

9. Кеер alarms clean, and test them weekly.

Basic Safety lnformation

1. DANGERS, WARNINGS, AND CAUTIONS ALERT YOU TO IMPORTANT OPERATING

ATTENTION TO THESE SITUATIONS.

2. THIS COMBINATION SMOKE & CARBON MONOXIDE ALARM IS ONLY APPROVED

3. THIS CARBON MONOXIDE ALARM IS DESIGNED TO DETECT CARBON MONOXIDE

4. CONSTANT EXPOSURES TO HIGH OR LOW HUMIDITY MAY REDUCE BATTERY

1. NEVER IGNORE ANY ALARM. FAILURE TO RESPOND CAN RESULT IN SERIOUS

4. THIS PRODUCT IS INTENDED FOR USE IN ORDINARY INDOOR LOCATIONS OF

(OSHA) COMMERCIAL OR INDUSTRIAL STANDARDS. INDIVIDUALS WITH MEDICAL

6. THIS DEVICE IS DESIGNED TO PROTECT INDIVIDUALS FROM THE ACUTE

4. lf an alarm cannot bе installed in the middle of а ceiling, install at а distance of 20 inches

5. lf an alarm is installed on а wall, it should bе at а distance of 4-12 inches (10-30 cm)

1. THIS ALARM SHOULD ВЕ INSTALLED ВУ А COMPETENT PERSON.

2. INSTALLATION OFTHE ALARM SHOULD NOT ВЕ USED AS А SUBSTITUTE FOR

CARBON MONOXIDE ALARMS

SMOKE & СО ALARMS

How to lnstall This Alarm