TOSHIBA MACHINE

WHITE

U.S.A. Specifications - Catalog #ECSX10-12

SPECIFICATIONS

This may look like

one machine...
...but it is so versatile, with a greater range of shot
sizes, you’ll think it was triplets.

It’s the new SX all-electric...packed with new and enhanced

features that give you extraordinary quality and unsurpassed
flexibility.

20% improvement in your dry cycle times More shot sizes with a single machine
The new SX’s friction-reducing linear bearing ways and With the SX, you get a wider range of barrel choices from
dynamic acceleration/deceleration control give you signifi- a single machine, enabling you to shorten changeover
cantly faster cycle times. times and move from project to project, quickly and easily.
As a result, you can be more competitive on new jobs and
Extending your mold life increase your shop’s flexibility without investing in new
Its shockless acceleration/deceleration programming helps equipment. And with quicker changeovers, you can be
reduce wear and tear on your mold, minimizing mold online and molding faster than ever before.
maintenance and maximizing mold life.
S3 - Simple, Steady, Smooth
Minimizing part contamination With its friction-free drive mechanism and faster com-
Bushing-free, grease-free tie bars reduce the possibility of munications software, the new SX improves high-speed,
contaminating molded parts. high-pressure performance, while maintaining greater
Uniform clamping molding stability.
force across mold The new SX’s high performance digital loadcell features
surface linear correction, increasing sensitivity while improving
The new SX features
a 5-point “Linkline”
toggle mechanism Output without linear tuning
that directs pressure 5-point Linkline mechanism for Output with linear tuning
to the center of the more uniform clamping force.

mold surface. As a
result, you achieve
uniform clamping force
across the entire mold
surface, improving
Left, uneven pressure. Right, injection accuracy and backpressure. The result is more
quality and minimizing
improved uniform clamping force. stabilized processing and screw recovery, and consistent
defect rates. shot-to-shot performance.
*Specifications are subject to change without notice
With uniform
Maximum injection mold surface
and holding pressure,
pressure are valued you
by thecan recycle
power of injection unit, not resin pressure.
Maximum injection and holding pressure are limited according to molding conditions.
tonnage, enabling you to maximize mold life and minimize
machine maintenance.

©2010 Toshiba Machine, Inc.

 ...but its shot
range says more

V50 Controller uses Real-Time Information iPAQET Remote Monitoring

With a 40% improvement in communication speed, the and Management Software
new V50 controller on the SX uses real-time input to report (Optional)
molding conditions and make automatic adjustments to A valuable upgrade to “iPAQET Lite,” the full version of
mold settings. This results in greater part repeatability and “iPAQET” offers a more powerful data management plat-
fewer rejects. form. Monitor up to 48 molding machines from anywhere,
in REAL TIME. iPaqet provides you with production mon-
User customization itoring, data collection and analysis, machine operation
The V50’s intuitive, touch- status, resin lot monitoring and more.
screen interface enables
you to customize machine Let the machine think for you
cells without investing in ad- Clamping force dynamic self-tuning (DST-PRESS):
ditional OEM programming. As an option setting, you can allow tie-bar strain sensors to
Up to 40 user-programma- automatically adjust clamping force based on direct feed-
ble outputs are available.
back of changing molding conditions such as increased
Monitoring and program- heat and expansion.) This results is more consistent pro-
ming are easy, thanks to a cessing from shot to shot throughout the processing cycle.
large 15-inch touch screen. Injection process condition dynamic self-tuning (DST-FILL):
And since screens look and You can further increase shot consistency by allowing the
work the same as previous machine to automatically change barrel temperatures
controllers, there’s little or and transfer points to compensate for material viscosity
no learning curve for current users. Just a single call to fluctuations.
Toshiba gets you answers to your programming questions.
Additional molding control software
In addition, the V50 includes “iPAQET Lite” data Virtual Hydraulic Injection (H1) circuit - Replicates the hy-
management software. A significant value-added benefit, draulic cascade effect to create more even flow rates into
it enhances your investment by providing you with produc- mold cavities. High sensitivity 3-stage mold protection -
tion monitoring, data collection and analysis, and more. Puts the machine into mold safety/shut down when torque
settings are exceeded during mold clamping. Ejector
Note 1: When using iPAQET, an Ethernet interface (standard) is required
on the injection molding machine itself. torque monitor - Helps prevent tool and part damage.
Note 2: All server, server peripherals and operating systems, and
Ask your Toshiba representative for a complete list of
LAN wiring are separately required for iPAQET.
standard and optional software.
 SPECIFICATIONS
ITEM UNIT EC55SX EC85SX EC110SX
tf 50 75 100
Clamp force
US Ton 55.1 82.7 110.2
HxV mm 410 x 360 410 x 360 460 x 410
Tie bar distance
HxV in 16.1 x 14.2 16.1 x 14.2 18.1 x 16.1

Platen HxV mm 510 x 460 580 x 530 660 x 610

dimension HxV in 20.1 x 18.1 22.8 x 20.9 26.0 x 24.0
mm 300 300 350
Clamp Stroke
in 11.8 11.8 13.8
CLAMP
mm 770 770 900
Maximum daylight
in 30.3 30.3 35.4
Min. x Max mm 150 ~ 470 150 ~ 470 180 ~ 550
Mold Height
Min. x Max in 5.9 ~ 18.5 5.9 ~ 18.5 7.1 ~ 21.7
tf 2 2 3
Ejector force
US Ton 2.2 2.2 3.3
mm 70 70 90
Ejector Stroke
in 2.8 2.8 3.5

Injection Unit U21 U22 U22 U32

Barrel code (1Y) (1A) (1B) (1Y) (1.5Y) (2Y) (2A) (2B) (1Y) (1.5Y) (2Y) (2A) (2B) (2Y) (2A) (2B)
mm 22 25 28 22 25 28 32 36 22 25 28 32 36 28 32 36
Screw Diameter
in 0.87 0.98 1.10 0.87 0.98 1.10 1.26 1.42 0.87 0.98 1.10 1.26 1.42 1.10 1.26 1.42
cm3 38 49 62 38 55 78 102 130 38 55 78 102 130 78 102 130
Injection Capacity
in3 2.3 3.0 3.8 2.3 3.4 4.8 6.2 7.9 2.3 3.4 4.8 6.2 7.9 4.8 6.2 7.9
g 35 45 57 35 51 72 94 120 35 51 72 94 120 72 94 120
PS
oz 1.2 1.6 2.0 1.2 1.8 2.5 3.3 4.2 1.2 1.8 2.5 3.3 4.2 2.5 3.3 4.2
Shot Volume
g 28 36 45 28 40 57 74 95 28 40 57 74 95 57 74 95
PE
oz 1.0 1.3 1.6 1.0 1.4 2.0 2.6 3.4 1.0 1.4 2.0 2.6 3.4 2.0 2.6 3.4

Maximum Injection MPa 284 220 175 284 276 287 220 174 284 276 287 220 174 287 220 174
Pressure PSI 41,200 31,900 25,400 41,200 40,000 41,600 31,900 25,200 41,200 40,000 41,600 31,900 25,200 41,600 31,900 25,200

Maximum Holding MPa 284 220 175 284 276 287 220 174 284 276 287 220 174 287 220 174
INJECTION Pressure PSI 41,200 31,900 25,400 41,200 40,000 41,600 31,908 25,237 41,200 40,000 41,600 31,900 25,200 41,600 31,900 25,200
cm3/s 76 98 123 76 98 123 161 204 76 98 123 161 204 123 161 204
Injection Rate STD
in /s
3
4.6 6.0 7.5 4.6 6.0 7.5 9.8 12.4 4.6 6.0 7.5 9.8 12.4 7.5 9.8 12.4

Injection mm/s 200 200 200 200

STD
Velocity in/s 7.9 7.9 7.9 7.9
cm3/s 190 245 308 190 245 308 402 509 190 245 308 402 509 308 402 509
Injection Rate HIGH
in /s
3
11.6 15.0 18.8 11.6 15.0 18.8 24.5 31.1 11.6 15.0 18.8 24.5 31.1 18.8 24.5 31.1

Injection mm/s 500 500 500 500

HIGH
Velocity in/s 19.7 19.7 19.7 19.7

Plasticizing g/sec 6.1 7.8 9.7 6.1 6.9 11.1 16.9 23.1 6.1 6.9 11.1 16.9 23.1 11.1 16.9 23.1
PS
capacity oz/sec 0.2 0.3 0.3 0.2 0.2 0.4 0.6 0.8 0.2 0.2 0.4 0.6 0.8 0.4 0.6 0.8
Screw speed RPM 420 420 380 420 390 400 390 350 420 390 400 390 350 400 390 350
kN 9.8 9.8 9.8 11.8
Nozzle touch force
US Ton 1.1 1.1 1.1 1.3

Heater Capacity kW 4.7 5.4 4.7 5.8 6.8 4.7 5.8 6.8 6.8

Machine LxWxH m 4.0 x 1.2 x 1.6 4.0 x 1.2 x 1.6 4.1 x 1.2 x 1.6 4.0 x 1.2 x 1.6 4.1 x 1.2 x 1.6 4.6 x 1.3 x 1.7
GENERAL Dimensions LxWxH ft 13.2 x 3.9 x 5.2 13.2 x 3.9 x 5.2 13.5 x 3.9 x 5.2 13.2 x 3.9 x 5.2 13.5 x 3.9 x 5.2 15.1 x 4.3 x 5.6
tf 3.0 3.2 3.3 4.2
Machine weight
US Ton 3.3 3.5 3.6 4.6
 EC110SX EC140SX EC200SX
100 130 180
110.2 143.3 198.4
460 x 410 510 x 460 560 x 510
18.1 x 16.1 20.1 x 18.1 22.0 x 20.1
660 x 610 720 x 670 790 x 740
26.0 x 24.0 28.3 x 26.4 31.1 x 29.1
350 400 450
13.8 15.7 17.7
900 950 1050
35.4 37.4 41.3
180 ~ 550 180 ~ 550 200 ~ 600
7.1 ~ 21.7 7.0 ~ 21.7 7.9 ~ 23.6
3 3 5
3.3 3.3 5.5
90 90 130
3.5 3.5 5.1

U34 U34 U44 U48

(2Y) (2A) (4Y) (4A) (4B) (2Y) (2A) (4Y) (4A) (4B) (4Y) (4A) (4B) (4Y) (6Y) (8Y) (8A) (8B)
28 32 36 40 45 28 32 36 40 45 36 40 45 36 40 45 50 55
1.10 1.26 1.42 1.57 1.77 1.10 1.26 1.42 1.57 1.77 1.42 1.57 1.77 1.42 1.57 1.77 1.97 2.17
78 102 162 201 254 78 102 162 201 254 162 201 254 162 226 318 392 475
4.8 6.2 9.9 12.3 15.5 4.8 6.2 9.9 12.3 15.5 9.9 12.3 15.5 9.9 13.8 19.4 23.9 29.0
72 94 149 185 234 72 94 149 185 234 149 185 234 149 208 293 361 437
2.5 3.3 5.3 6.5 8.3 2.5 3.3 5.3 6.5 8.3 5.3 6.5 8.3 5.3 7.3 10.3 12.7 15.4
57 74 118 147 185 57 74 118 147 185 118 147 185 118 165 232 286 347
2.0 2.6 4.2 5.2 6.5 2.0 2.6 4.2 5.2 6.5 4.2 5.2 6.5 4.2 5.8 8.2 10.1 12.2
287 220 247 200 158 287 220 247 200 158 247 200 158 247 253 247 200 165
41,600 31,900 35,800 29,000 22,900 41,600 31,900 35,800 29,000 22,900 35,800 29,000 22,900 35,800 36,700 35,800 29,000 23,900
287 220 247 200 158 287 220 247 200 158 247 200 158 247 253 247 200 165
41,600 31,900 35,800 29,000 22,900 41,600 31,900 35,800 29,000 22,900 35,800 29,000 22,900 35,800 36,700 35,800 29,000 23,900
123 161 204 251 318 123 161 204 251 318 204 251 318 163 201 254 314 380
7.5 9.8 12.4 15.3 19.4 7.5 9.8 12.4 15.3 19.4 12.4 15.3 19.4 9.9 12.3 15.5 19.2 23.2
200 200 200 160
7.9 7.9 7.9 6.3
216 281 356 440 557 216 281 356 440 557 356 440 557 305 377 477 589 713
13.2 17.1 21.7 26.8 34.0 13.2 17.1 21.7 26.8 34.0 21.7 26.8 34.0 18.6 23.0 29.1 35.9 43.5
350 350 350 300
13.8 13.8 13.8 11.8
11.1 16.9 23.1 30.6 33.3 11.1 16.9 23.1 30.6 33.3 23.1 30.6 33.3 18.9 27.2 33.3 44.4 52.8
0.4 0.6 0.8 1.1 1.2 0.4 0.6 0.8 1.1 1.2 0.8 1.1 1.2 0.7 1.0 1.2 1.6 1.9
400 390 350 320 285 400 390 350 320 285 350 320 285 285 285 285 255 230
11.8 11.8 29.4 29.4
1.3 1.3 3.3 3.3

6.8 11.2 6.8 11.2 11.2 11.2 13.6 15.2

4.6 x 1.3 x 1.7 4.9 x 1.3 x 1.7 4.8 x 1.4 x 1.8 4.9 x 1.3 x 1.7 5.2 x 1.4 x 1.8 5.7 x 1.5 x 1.9 5.7 x 1.5 x 1.9 5.9 x 1.5 x 1.9 6.0 x 1.5 x 1.9
15.1 x 4.3 x 5.6 16.1 x 4.3 x 5.6 15.7 x 4.6 x 5.9 16.7 x 4.6 x 5.9 17.1 x 4.6 x 5.9 18.7 x 4.9 x 6.2 18.7 x 4.9 x 6.2 19.4 x 4.9 x 6.2 19.7 x 4.9 x 6.2
4.2 4.3 5.2 5.3 7.0 7.0 7.3
4.6 4.7 5.7 5.8 7.7 7.7 8.0
 SPECIFICATIONS
ITEM UNIT EC250SX EC310SX
tf 230 280
Clamp force
US Ton 253.5 308.6
Tie bar HxV mm 610 x 560 730 x 660
distance HxV in 24.0 x 22.0 28.7 x 25.9
Platen HxV mm 880 x 830 1030 x 960
dimension HxV in 34.6 x 32.7 40.5 x 37.7
mm 550 600
Clamp Stroke
in 21.7 23.6
CLAMP
mm 1230 1350
Maximum daylight
in 48.4 53.1
Mold Min. x Max mm 250 ~ 680 250 ~ 750
Height Min. x Max in 9.8 ~ 26.8 9.8 ~ 29.5
tf 5 6
Ejector force
US Ton 5.5 6.6
mm 130 150
Ejector Stroke
in 5.1 5.9

Injection Unit U48 i17 i8 i17

Barrel code (4Y) (6Y) (8Y) (8A) (8B) Y AT B Y A B Y AT B
mm 36 40 45 50 55 50 60 70 45 50 55 50 60 70
Screw Diameter
in 1.42 1.57 1.77 1.97 2.17 1.97 2.36 2.76 1.77 1.97 2.17 1.97 2.36 2.76
cm3 162 226 318 392 475 589 848 1155 318 392 475 589 848 1155
Injection Capacity
in3 9.9 13.8 19.4 23.9 29.0 35.9 51.7 70.5 19.4 23.9 29.0 35.9 51.7 70.5
g 149 208 293 361 437 542 780 1062 293 361 437 542 780 1063
PS
Shot oz 5.3 7.3 10.3 12.7 15.4 19.1 27.5 37.5 10.3 12.7 15.4 19.1 27.5 37.5
Volume g 118 165 232 286 347 430 619 843 232 286 347 430 619 843
PE
oz 4.2 5.8 8.2 10.1 12.2 15.2 21.8 29.7 8.2 10.1 12.2 15.2 21.8 29.7
Maximum Injection MPa 247 253 247 200 165 288 200 147 247 200 165 288 200 147
Pressure PSI 35,800 36,700 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300
Maximum Holding MPa 247 253 247 200 165 288 200 147 247 200 165 288 200 147
Pressure PSI 35,800 36,700 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300
cm3/s 163 201 254 314 380 314 452 616 254 314 380 314 452 616
Injection Rate STD
in3/s 9.9 12.3 15.5 19.2 23.2 19.2 27.6 37.6 15.5 19.2 23.2 19.2 27.6 37.6
Injection mm/s 160 160 160 160
STD
INJECTION Velocity in/s 6.3 6.3 6.3 6.3
cm3/s 305 377 477 589 713 589 848 1155 477 589 713 589 848 1155
Injection Rate HIGH
in3/s 18.6 23.0 29.1 35.9 43.5 35.9 51.7 70.5 29.1 35.9 43.5 35.9 51.7 70.5
Injection mm/s 300 300 300 300
HIGH
Velocity in/s 11.8 11.8 11.8 11.8
g/sec 18.9 27.2 33.3 44.4 52.8 35.8 64.4 75.8 33.3 44.4 52.8 44.4 64.4 75.8
STD
Plasticizing oz/sec 0.7 1.0 1.2 1.6 1.9 1.3 2.3 2.7 1.2 1.6 1.9 1.6 2.3 2.7
capacity (PS) HIGH g/sec – – – – – – – – – – – – – –
TORQUE oz/sec – – – – – – – – – – – – – –
Nm – – – – – – – – – – – – – –
STD
Screw ft-lbf – – – – – – – – – – – – – –
torque HIGH Nm – – – – – – – – – – – – – –
TORQUE ft-lbf – – – – – – – – – – – – – –
STD RPM 285 285 285 255 230 255 220 180 285 255 230 255 220 180
Screw
speed HIGH
RPM – – – – – – – – – – – – – –
TORQUE
kN 29.4 29.4 29.4 29.4
Nozzle touch force
US Ton 3.3 3.3 3.3 3.3

Heater Capacity kW 11.2 13.6 15.2 21.6 15.2 15.2

Machine LxWxH m 6.0 x 1.6 x 2.0 6.2 x 1.6 x 2.0 6.3 x 1.6 x 2.0 6.8 x 1.8 x 2.2 6.7 x 2.0 x 2.1 7.0 x 2.0 x 2.1
GENERAL Dim. LxWxH ft 19.6 x 5.2 x 6.6 20.3 x 5.2 x 6.6 20.7 x 5.2 x 6.6 21.7 x 5.6 x 7.2 22.0 x 6.6 x 6.9 23.0 x 6.6 x 6.9
tf 9.2 9.3 12.4 13.5 14.7
Machine weight
US Ton 10.1 10.3 13.6 14.9 16.2
 EC390SX EC500SX EC610SX
350 450 550
385.8 496 606.3
810 x 730 870 x 810 960 x 900
31.9 x 28.7 34.3 x 31.9 37.8 x 35.4
1110 x 1030 1230 x 1160 1365 x 1300
43.7 x 40.6 48.4 x 45.7 53.7 x 51.2
650 800 900
25.6 31.5 35.4
1420 1600 1700
55.9 63.0 66.9
300 ~ 770 350 x 800 400 x 800
11.8 ~ 30.3 13.8 x 31.5 15.7 x 31.5
6 13 13
6.6 14.3 14.3
150 180 180
5.9 7.1 7.1

i8 i17 i26 i26 i36 i26 i36

Y A B Y AT B AT B AT B AT B AT B AT B
45 50 55 50 60 70 70 80 70 80 80 90 70 80 80 90
1.77 1.97 2.17 1.97 2.36 2.76 2.76 3.15 2.76 3.15 3.15 3.54 2.76 3.15 3.15 3.54
318 392 475 589 848 1155 1340 1750 1340 1750 1880 2380 1340 1750 1880 2380
19.4 23.9 29.0 35.9 51.7 70.5 81.8 106.8 81.8 106.8 114.7 145.2 81.8 106.8 114.7 145.2
293 361 437 542 780 1063 1233 1610 1233 1610 1730 2190 1233 1610 1730 2190
10.3 12.7 15.4 19.1 27.5 37.5 43.5 56.8 43.5 56.8 61.0 77.2 43.5 56.8 61.0 77.2
232 286 347 430 619 843 978 1278 978 1278 1372 1737 978 1278 1372 1737
8.2 10.1 12.2 15.2 21.8 29.7 34.5 45.1 34.5 45.1 48.4 61.3 34.5 45.1 48.4 61.3
247 200 165 288 200 147 190 145 190 145 190 150 190 145 190 150
35,800 29,000 23,900 41,800 29,000 21,300 27,600 21,000 27,600 21,000 27,600 21,800 27,600 21,000 27,600 21,800
247 200 165 288 200 147 160 122 160 122 160 126 160 122 160 126
35,800 29,000 23,900 41,800 29,000 21,300 23,200 17,700 23,200 17,700 23,200 18,300 23,200 17,700 23,200 18,300
254 314 380 314 452 616 616 804 616 804 704 891 616 804 704 891
15.5 19.2 23.2 19.2 27.6 37.6 37.6 49.1 37.6 49.1 43.0 54.4 37.6 49.1 43.0 54.4
160 160 160 160 140 160 140
6.3 6.3 6.3 6.3 5.5 6.3 5.5
477 589 713 589 848 1155 – – – – – – – – – –
29.1 35.9 43.5 35.9 51.7 70.5 – – – – – – – – – –
300 300 – – – – – – – – – –
11.8 11.8 – – – – – – – – – –
33.3 44.4 52.8 35.8 64.4 75.8 72.2 94.4 72.2 94.4 94.4 111.1 72.2 94.4 94.4 111.1
1.2 1.6 1.9 1.3 2.3 2.7 2.5 3.3 2.5 3.3 3.3 3.9 2.5 3.3 3.3 3.9
– – – – – – 47.2 63.9 47.2 63.9 61.1 77.8 47.2 63.9 61.1 77.8
– – – – – – 1.7 2.3 1.7 2.3 2.2 2.7 1.7 2.3 2.2 2.7
– – – – – – 2580 2580 2580 2580 3310 3310 2580 2580 3310 3310
– – – – – – 1903 1903 1903 1903 2441 2441 1903 1903 2441 2441
– – – – – – 3310 3310 3310 3310 4610 4610 3310 3310 4610 4610
– – – – – – 2441 2441 2441 2441 3400 3400 2441 2441 3400 3400
285 255 230 255 220 180 180 170 180 170 170 150 180 170 170 150

– – – – – – 120 120 120 120 115 115 120 120 115 115

29.4 29.4 4.5 4.5 6 4.5 6

3.3 3.3 5.0 5.0 6.6 5.0 6.6

21.6 21.6 22.3 22.3 29.5 22.3 29.5

7.0 x 2.1 x 2.2 7.3 x 2.1 x 2.2 7.9 x 2.1 x 2.2 8.0 x 2.2 x 2.3 8.4 x 2.3 x 2.3 8.5 x 2.3 x 2.3 8.3 x 2.3 x 2.3 8.7 x 2.4 x 2.3 8.8 x 2.4 x 2.3
23.0 x 6.9 x 7.2 24.0 x 6.9 x 7.2 25.9 x 6.9 x 7.5 26.2 x 7.2 x 7.5 27.6 x 7.5 x 7.5 27.9 x 7.5 x 7.5 27.2 x 7.5 x 7.5 28.5 x 7.9 x 7.5 28.9 x 7.9 x 7.5
17.2 17.2 18.7 25.5 26.7 30.2 31.4
19.0 19.0 20.6 28.1 29.4 33.3 34.6
 SPECIFICATIONS
ITEM UNIT EC720SX EC950SX
tf 650 850
Clamp force
US Ton 716.5 937
Tie bar HxV mm 1060 x 960 1320 x 1320
distance HxV in 41.7 x 37.7 51.9 x 51.9
Platen HxV mm 1500 x 1400 1790 x 1790
dimension HxV in 59.0 x 55.1 70.4 x 70.4
mm 1000 1200
Clamp Stroke
in 39.4 47.2
CLAMP
mm 2050 2300
Maximum daylight
in 80.7 90.6
Mold Min. x Max mm 450 x 1050 500 x 1100
Height Min. x Max in 17.7 x 41.3 19.6 x 43.3
tf 18 18
Ejector force
US Ton 19.8 19.8
mm 200 200
Ejector Stroke
in 7.9 7.9

Injection Unit i61 i78 i61 i78

Barrel code AT B AT B AT B AT B
mm 95 105 105 120 95 105 105 120
Screw Diameter
in 3.74 4.13 4.13 4.72 3.74 4.13 4.13 4.72
cm3 3150 3850 4320 5650 3150 3850 4320 5650
Injection Capacity
in3 192.2 234.9 263.6 344.8 192.2 234.9 263.6 344.8
g 2898 3542 3974 5198 2898 3542 3974 5198
PS
Shot oz 102.2 124.9 140.2 183.3 102.2 124.9 140.2 183.3
Volume g 2300 2811 3154 4125 2300 2811 3154 4125
PE
oz 81.1 99.2 111.3 145.5 81.1 99.2 111.3 145.5
Maximum Injection MPa 180 147 180 138 180 147 180 138
Pressure PSI 26,100 21,300 26,100 20,000 26,100 21,300 26,100 20,000
Maximum Holding MPa 150 123 150 115 150 123 150 115
Pressure PSI 21,800 17,800 21,800 16,700 21,800 17,800 21,800 16,700
cm3/s 1063 1299 1299 1696 1063 1299 1299 1696
Injection Rate STD
in3/s 64.9 79.3 79.3 103.5 64.9 79.3 79.3 103.5
Injection mm/s 150 150 150 150
STD
INJECTION Velocity in/s 5.9 5.9 5.9 5.9
cm3/s – – – – – – – –
Injection Rate HIGH
in3/s – – – – – – – –
Injection mm/s – – – – – – – –
HIGH
Velocity in/s – – – – – – – –
g/sec 116.7 136.1 136.1 161.1 116.7 136.1 136.1 161.1
STD
Plasticizing oz/sec 4.1 4.8 4.8 5.7 4.1 4.8 4.8 5.7
capacity (PS) HIGH g/sec 80.6 102.8 75 102.8 80.6 102.8 75 102.8
TORQUE oz/sec 2.8 3.6 2.6 3.6 2.8 3.6 2.6 3.6
Nm 5500 5500 7090 7090 5500 5500 7090 7090
STD
Screw ft-lbf 4057 4057 5229 5229 4057 4057 5229 5229
torque HIGH Nm 7090 7090 10300 10300 7090 7090 10300 10300
TORQUE ft-lbf 5229 5229 7597 7597 5229 5229 7597 7597
STD RPM 140 127 127 110 140 127 127 110
Screw
speed HIGH
RPM 95 95 71 71 95 95 71 71
TORQUE
kN 6 6
Nozzle touch force
US Ton 6.6 6.6

Heater Capacity kW 44.0 57.2 44.0 57.2

Machine LxWxH m 9.8 x 2.6 x 2.7 10.1 x 2.6 x 2.7 10.4 x 2.6 x 2.7 10.6 x 2.9 x 2.7 10.6 x 2.9 x 2.7 10.9 x 2.9 x 2.7
GENERAL Dim. LxWxH ft 32.1 x 8.6 x 8.9 33.2 x 8.6 x 8.9 34.1 x 8.6 x 8.9 34.8 x 9.5 x 8.9 34.8 x 9.5 x 8.9 35.8 x 9.5 x 8.9
tf 40.0 41.5 53.5 55.0
Machine weight
US Ton 44.1 45.7 59.0 60.6
STANDARD FEATURES
EC-SX SERIES - AC SERVO ELECTRIC INJECTION MOLDING MACHINES
Injection/Plasticization Clamp unit/ejector and Clamp unit/ejector and functions
continued
u Open Nozzle functions
u Ejector retraction check circuit
u Barrel - anti-corrosion/wear u Link Line Toggle Unit
u Ejector plate, ejecting rod
u Standard Screw assembly- high knead- u Double rigid body platen
ing DBG design u Gate cut circuit
u Mold Platen
u Hopper inlet rust-preventive sleeve u Ejection force digital setting
u Locating Hold
u Barrel Heater u Ejection hold time setting
u Movable Platen supporting device
u Friction Free Drive u Ejection during mold opening
u Mechanical safety device
u Digital Load Cell u Ejection torque monitor
u Holes tapped for installation of take-
u Purge shield out robot u Mold open halt - Enables mold open-
ing at an arbitrary position
u Double heater cover u Ejection servo motor with brake
u DST-Fill u Automatic lubricator
Controller (EC-SX Series)
u Pressure linear correction u Dynamic acceleration/deceleration
control
u Step switch/Ten key input
u Programmed purge circuit
u DST-Press Control
u Setting data memory for 300 sets of
u VHI control molds
u 3-Step high-speed programmed
u FIT Control u External interface
control
u Laminar control u Digital display
u Clamp pressure digital display in two
u EC-SX 12-Speed/8-pressure injection (2) steps u Graphic display
programmed control u Sensitive mold protection control - u Profile display/storing/measure func-
u Shift to hold mode selection Provides torque monitor and limiter tions
Shift to hold correction control in 2-high-speed
u u Quality monitoring
Injection speed FF Control ranges, and torque/time limiter in
u u Diagnostic function
low-pressure clamp range
u Screw speed/back pressure pro- u Operation select function at produc-
grammed control
u Automatic mold thickness adjust
tions completion
circuit
u Automatic screw back pressure reduc- u MOLDLYZER
tion control
u Low pressure and slow speed circuit
for mold set-up mode u iPAQET LITE
u Automatic charging deceleration con-
u Lock-Up Delay Timer u LCD Touch Panel
trol
u Lock-Up Speed digital setting u High-Speed control cycle
u Decompress before/after charge
u Setting of number of repeated u List setting screen
u Charge delay timer
ejections u Operation indicator
u Screw cold start prevention device
u 3-Step ejection speed programmed u External output signal customize
u Heater SSR Control control function
u Heater band failure indicating circuit u Repeated ejection control u Password function
u Hopper Throat temperature controller u RA ejection control
u Barrel temperature FF Control
u Programmed Heat-Up circuit
u Simultaneous barrel heat-up control
u Barrel Temperature shift circuit
u Retention resin overheat prevention

u
circuit
Manual back pressure setting
TOSHIBA MACHINE
PANTONE 193

TOSHIBA MACHINE
CMYK
EC-SX Dimensions

SCREW DIA L L1 L2 D D1 H H1 H2
MODEL INJ. UNIT
mm Inch
22/25 155.1 35.0
U21
28 158.3 37.4
EC55SX 22 155.1 35.0
68.9 46.9 23.8 62.4 46.1 62.0
EC85SX 25 158.3 37.4
U22
28/32 161.5 40.7
36 164.7 43.8
28/32 180.8 41.9
U32
36 184.0 45.0
EC110SX 28/32 180.8 82.3 41.9 49.8 25.2 64.8 46.7 64.6
U34 36/40 191.1 49.2
45 195.2 53.3
28/32 187.7 41.9
EC140SX U34 36/40 198.6 89.2 49.8 54.7 27.4 67.7 48.5 66.5
36 202.7 53.9
36/40 223.3 51.7
U44
45 227.4 55.8
36 223.3 51.7
EC200SX 102.3 60.2 30.6 71.0 49.3 70.5
40 230.7 56.2
U48
45/50 234.6 60.1
55 238.7 64.2
36 237.0 53.5
40 244.3 58.0
EC250SX U48 114.2 63.9 32.4 76.6 52.0 73.3
45/50 248.2 61.9
55 252.3 66.0
EC390SX U5 50/60/70 284.3 132.8 85.3 82.1 44.2 84.1 53.6 84.6

Note: This is the real height without mounting pads.

All dimensions subjec tto change without notice.
EC-SX Dimensions

SCREW DIA L L1 L2 L3 D D1 H H1 H2
MODEL INJ. UNIT
mm Inch
70 83.7
i26 313.6 7.6 86.2
80 91.5
EC500SX 145.9 81.9 41.7 86.6 55.1
80 91.7 6.9
i36 324.8 87.8
90 99.6 6.9
70 85.2
i26 326.6 7.6 86.2
80 93.1
EC610SX 157.3 87.8 45.9 86.6 55.1
80 93.3 14.8
i36 337.8 87.8
90 101.2 6.9
95 111.5 6.8
i61 99.4
105 119.4 14.6
EC720SX 380.9 181.1 97.6 50.4 86.6 55.1
105 127.2
i78 22.5 101.4
120 139.1
95 104.7 0
i61 103.4
105 112.6 6.6
EC950SX 414.8 204.7 112.2 60.4 94.5 59.1
105 120.4 14.4
i78 105.4
120 132.2 26.3

NOTES Note: This is the real height without mounting pads.

All dimensions subjec tto change without notice.
Reach for the impossible.
Achieve the incredible.
Your investment in Toshiba Machine molding machines and equipment
brings with it our comprehensive committment to service and support. You
have access to assistance and technical help in locations across the country.
Plus, on-site assistance when you need a hands-on solution.
We appreciate the opportunity to become part of your company and look
forward to providing solutions that help you “achieve the incredible.”

Toshiba Machine Co., America

Chicago Head Office
755 Greenleaf Avenue
Elk Grove Village, IL 60007
Ph: 847-593-1616
Fax: 847-593-1728
Sales, Service, Technical Center and
Technical Support

Toshiba Machine Co., America

Los Angeles Office
1440 South Balboa Avenue
Ontario, CA 91761
Ph: 909-923-4009
Fax: 909-923-7258
Sales, Service, Technical Center and
Technical Support

Toshiba Machine Co., America

New Jersey Office
1578 Sussex Turnpike South
Randolph, NJ 07869
Ph: 973-252-9956
Fax: 973-252-9959
Sales, Service, Technical Center and
Technical Support

Toshiba Machine Co., Ltd.

2-2, Uchisaiwaicho 2-Chome, Chiyoda-ku, Tokyo 100-8503, Japan
Ph: +81-3-3509-0319; Fax: +81-3-3509-0331