Bcs

ELECTRICAL & POWER CONTROL
BCS
A
B
SECTION
BODY CONTROL SYSTEM C
E
CONTENTS
BCM COMMON ITEM : CONSULT-III Function (BCM - F
COMMON ITEM) .....................................................15
BASIC INSPECTION .................................... 3
BCM ...........................................................................15
G
INSPECTION AND ADJUSTMENT ..................... 3 BCM : CONSULT-III Function (BCM - BCM) ...........15
ADDITIONAL SERVICE WHEN REPLACING DOOR LOCK ..............................................................16

CONTROL UNIT .......................................................... 3 DOOR LOCK : CONSULT-III Function (BCM - H
ADDITIONAL SERVICE WHEN REPLACING DOOR LOCK) ..........................................................16
CONTROL UNIT : Description .................................. 3
REAR WINDOW DEFOGGER ...................................16
ADDITIONAL SERVICE WHEN REPLACING
REAR WINDOW DEFOGGER : CONSULT-III I
CONTROL UNIT : Special Repair Requirement ...... 3
Function (BCM - REAR DEFOGGER) .....................16
CONFIGURATION ....................................................... 3
CONFIGURATION : Description ............................... 3 BUZZER .....................................................................17
J
CONFIGURATION : Special Repair Requirement...... 4 BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ..........................................................................17
FUNCTION DIAGNOSIS ............................... 5 INT LAMP ...................................................................17 K
BODY CONTROL SYSTEM ................................ 5 INT LAMP : CONSULT-III Function (BCM - INT
System Description ................................................... 5 LAMP) ......................................................................17
Component Parts Location ........................................ 6 MULTIREMOTE ENT .................................................18 L
COMBINATION SWITCH READING SYSTEM MULTIREMOTE ENT : CONSULT-III Function

(BCM - MULTIREMOTE ENT) .................................18
..... 7
BCS
System Diagram ........................................................ 7 HEADLAMP ...............................................................20
System Description ................................................... 7 HEADLAMP : CONSULT-III Function (BCM -
Component Parts Location ...................................... 10 HEAD LAMP) ...........................................................20
N
SIGNAL BUFFER SYSTEM ...............................12 WIPER ........................................................................21
System Diagram ...................................................... 12 WIPER : CONSULT-III Function (BCM - WIPER)....21
System Description ................................................. 12
FLASHER ...................................................................22 O
POWER CONSUMPTION CONTROL SYS- FLASHER : CONSULT-III Function (BCM -
TEM ....................................................................13 FLASHER) ...............................................................22
System Diagram ...................................................... 13 P
AIR CONDITIONER ...................................................22
System Description ................................................. 13
AIR CONDITIONER : CONSULT-III Function
Component Parts Location ...................................... 14
(BCM - AUTO AIR CONDITIONER) ........................22
DIAGNOSIS SYSTEM (BCM) ............................15
COMB SW ..................................................................23
COMMON ITEM ......................................................... 15 COMB SW : CONSULT-III Function (BCM -
COMB SW) ..............................................................23
Revision: November 2008 BCS-1 2009 Titan

IMMU ......................................................................... 23 COMBINATION SWITCH INPUT CIRCUIT ....... 31
IMMU : CONSULT-III Function (BCM - IMMU) ....... 23 Diagnosis Procedure ............................................... 31
Special Repair Requirement ................................... 32
BATTERY SAVER .................................................... 23
BATTERY SAVER : CONSULT-III Function (BCM COMBINATION SWITCH OUTPUT CIRCUIT ... 33
- BATTERY SAVER) .............................................. 24 Diagnosis Procedure ............................................... 33
RETAINED PWR ....................................................... 24
RETAINED PWR : CONSULT-III Function (BCM - COMBINATION SWITCH .................................. 34
RETAINED PWR) ................................................... 24 Description .............................................................. 34
Diagnosis Procedure ............................................... 34
SIGNAL BUFFER ...................................................... 24
SIGNAL BUFFER : CONSULT-III Function (BCM ECU DIAGNOSIS ....................................... 36
- SIGNAL BUFFER) ................................................ 24
BCM (BODY CONTROL MODULE) .................. 36
AIR PRESSURE MONITOR ...................................... 25
Reference Value ..................................................... 36
AIR PRESSURE MONITOR : Diagnosis Descrip-
Terminal Layout ...................................................... 38
tion .......................................................................... 25
Physical Values ....................................................... 38
AIR PRESSURE MONITOR : CONSULT-III Func-
Wiring Diagram ....................................................... 44
tion .......................................................................... 26
Fail Safe ................................................................. 48
THEFT ALM .............................................................. 27 DTC Inspection Priority Chart ............................... 49
THEFT ALM : CONSULT-III Function (BCM - DTC Index .............................................................. 49
THEFT ALM) .......................................................... 27
SYMPTOM DIAGNOSIS ............................ 51
COMPONENT DIAGNOSIS ........................ 28
COMBINATION SWITCH SYSTEM SYMP-
U1000 CAN COMM CIRCUIT ............................ 28 TOMS ................................................................. 51
Description .............................................................. 28 Symptom Table ....................................................... 51
DTC Logic ............................................................... 28
Diagnosis Procedure .............................................. 28 PRECAUTION ............................................ 52
U1010 CONTROL UNIT (CAN) ......................... 29 PRECAUTIONS ................................................. 52

DTC Logic ............................................................... 29 Supplemental Restraint System (SRS) "AIR BAG"
Diagnosis Procedure .............................................. 29 and "SEAT BELT PRE-TENSIONER" .................... 52
ON-VEHICLE REPAIR ............................... 53
POWER SUPPLY AND GROUND CIRCUIT ..... 30
Diagnosis Procedure .............................................. 30
BCM (BODY CONTROL MODULE) .................. 53
Removal and Installation ......................................... 53

INSPECTION AND ADJUSTMENT
< BASIC INSPECTION > [BCM]
BASIC INSPECTION A
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
B
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003788997
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before C
replacement.
Configuration has three functions as follows
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM. D
• WRITE CONFIGURATION - Manual selection is the function to select and write vehicle configuration on
BCM manually.
• WRITE CONFIGURATION - Config file is the function to write vehicle configuration with the data extracted
E
from current BCM.
CAUTION:
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order. F
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re- G
quirement INFOID:0000000003788998
1. SAVING VEHICLE SPECIFICATION H
Perform “READ CONFIGURATION” with CONSULT-III to save or print current vehicle specification.
I
>> GO TO 2
2. REPLACE BCM
J
Replace BCM. Refer to BCS-53, "Removal and Installation".
>> GO TO 3 K
3. WRITING VEHICLE SPECIFICATION
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” with
CONSULT-III to write vehicle specification. Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING L
CONTROL UNIT : Special Repair Requirement".
>> GO TO 4 BCS
4. INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS) N
>> WORK END

CONFIGURATION O
CONFIGURATION : Description INFOID:0000000003788999
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM. P
Configuration has three functions as follows
• READ CONFIGURATION is the function to read (extract) vehicle configuration of current BCM.
• WRITE CONFIGURATION - Manual selection is the function to select and write vehicle configuration on
BCM manually.
• WRITE CONFIGURATION - Config file is the function to write vehicle configuration with the data extracted
from current BCM.
CAUTION:

< BASIC INSPECTION > [BCM]
• When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III.
• Complete the procedure of WRITE CONFIGURATION in order.
• If you set incorrect WRITE CONFIGURATION, incidents will occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
CONFIGURATION : Special Repair Requirement INFOID:0000000003789000
1. WRITING VEHICLE SPECIFICATION

Perform “WRITE CONFIGURATION” with CONSULT-III.
When writing saved data>>GO TO 2

When writing manually>>GO TO 3
2. PERFORM “WRITE CONFIGURATION - CONFIG FILE”
Perform “WRITE CONFIGURATION - Config file” with CONSULT-III.
>> WORK END

3. PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
For “WRITE CONFIGURATION - Manual selection”, using the following flow chart, identify the correct model
and configuration list.
Confirm and/or change setting value for each item according to the configuration list.
Depending on CONSULT-III software version being used, some or all of the write configuration items shown in
the following configuration lists may be displayed. If an item does not display on the CONSULT-III “WRITE
CONFIGURATION - Manual selection” screen, then it is an auto setting item and it cannot be manually set or
changed.
MANUAL SETTING ITEM

Items Setting value
KEYLESS ENTRY WITH⇔WITHOUT
I-KEY WITHOUT
AUTO LIGHT WITH⇔WITHOUT
FR FOG LAMP WITH⇔WITHOUT
DTRL WITH⇔WITHOUT
SPEED SNS WIP WITH⇔WITHOUT
DISPLAY STYLE MODE11⇔MODE22
THEFT ALARM WITH⇔WITHOUT
1: Without NAVI
2: With NAVI
Do not apply MODE3 or MODE4
NOTE:
Confirm vehicle model. Refer to GI-19, "Model Variation".
>> WORK END

BODY CONTROL SYSTEM
< FUNCTION DIAGNOSIS > [BCM]
FUNCTION DIAGNOSIS A
BODY CONTROL SYSTEM
System Description INFOID:0000000003789001
B
OUTLINE
• BCM (body control module) controls the various electrical components. It inputs the information required to C
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power consump- D
tion control function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings. E
BCM control function list
System Refer to F
Combination switch reading system BCS-7, "System Diagram"
Signal buffer system BCS-12, "System Diagram"
G
Power consumption control system BCS-13, "System Diagram"
Auto light system (if equipped) EXL-9, "System Diagram"
Turn signal and hazard warning lamp system EXL-14, "System Diagram" H
Headlamp system EXL-7, "System Diagram"
Front fog lamp system (if equipped) EXL-13, "System Diagram"
I
Daytime running light system (Canada models) EXL-11, "System Diagram"
Interior room lamp control system INL-6, "System Diagram"
Step lamp system (if equipped) INL-6, "System Diagram" J
Interior room lamp battery saver system INL-10, "System Diagram"
Front wiper and washer system WW-4, "System Diagram"
Warning chime system WCS-4, "WARNING CHIME SYSTEM : System Diagram" K
Door lock system (if equipped) DLK-12, "DOOR LOCK AND UNLOCK SWITCH : System Diagram"
(NATS) Nissan anti-theft system (if equipped) SEC-7, "System Diagram" L
Vehicle security system (if equipped) SEC-10, "System Diagram"
Rear window defogger system (if equipped) DEF-5, "System Diagram"
Remote keyless entry system (if equipped) DLK-14, "REMOTE KEYLESS ENTRY : System Diagram" BCS
Power window system (if equipped) PWC-6, "System Diagram"
BCS-24, "RETAINED PWR : CONSULT-III Function (BCM - RETAINED
RAP (retained accessory power) system N
PWR)"
TPMS (tire pressure monitoring system) WT-8, "System Diagram"

BODY CONTROL SYSTEM
Component Parts Location INFOID:0000000003789002
• BCM M18, M19, M20 (view with instrument panel removed)
LEIA0068E

COMBINATION SWITCH READING SYSTEM
A
System Diagram INFOID:0000000003789003
LIIA1323E
I
J
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
K
• BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX L
BCS

Combination switch circuit
LIIA1325E
Combination switch INPUT-OUTPUT system list

System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 — — HEADLAMP 2 HI BEAM
INPUT 4 — INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INPUT 5 INT VOLUME 2 — — FR FOG —
NOTE:
Headlamp has a dual system switch.
COMBINATION SWITCH READING FUNCTION

Description
• BCM reads the status of the combination switch at 10 ms interval normally.
JPMIA0067GB
NOTE:
BCM reads the status of the combination switch at 20 ms interval when BCM is controlled at low power con-
sumption control mode.
• BCM operates as follows and judges the status of the combination switch.
- INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 5 → 4 → 3 → 2 → 1.

- The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of
the transistor on OUTPUT side if any (1 or more) switches are ON. A
- It reads this change of the voltage as the status signal of the combination switch.
JPMIA0068GB
I
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
J
Example 1: When a switch (TURN RH switch) is turned ON
• The circuit between INPUT 1 and OUTPUT 5 is formed when the TURN RH switch is turned ON.
K
BCS
ALMIA0297GB
• BCM detects the combination switch status signal “1E” when the signal of OUTPUT 5 is input to INPUT 1. P
• BCM judges that the TURN RH switch is ON when the signal “1E” is detected.
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON

• The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the
TURN RH switch and FR WIPER LOW switch are turned ON.
ALMIA0298GB
• BCM detects the combination switch status signal “1CE” when the signals of OUTPUT 3 and OUTPUT 5 are
input to INPUT 1.
• BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal “1CE” is
detected.
WIPER INTERMITTENT DIAL POSITION SETTING (FRONT WIPER INTERMITTENT OPERATION)
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2 and 3 switches.
Intermittent INT VOLUME switch ON/OFF status

Wiper intermittent
operation delay
dial position INT VOLUME 1 switch INT VOLUME 2 switch INT VOLUME 3 switch
interval
1 ON ON ON
Short
2 ↑ ON ON OFF
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
6 ↓ OFF ON ON
Long
7 OFF ON OFF
ALMIA0299ZZ

1. BCM M18, M19, M20 (view with in- 2. Combination switch (lighting and 3. Combination switch (wiper and A
strument panel removed) turn signal switch) M28 washer switch) M28
BCS

SIGNAL BUFFER SYSTEM
SIGNAL BUFFER SYSTEM
ALMIA0263GB
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Signal transmission function list
Signal name Input Output Description

Transmits the received oil pres-
Oil pressure switch signal IPDM E/R (CAN) Combination meter (CAN) sure switch signal via CAN
communication.

POWER CONSUMPTION CONTROL SYSTEM
A
ALMIA0300GB F
G
OUTLINE
• BCM incorporates a power consumption control function that reduces the power consumption according to
the vehicle status. H
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination meter) that operates with the ignition switch OFF.
Normal mode (wake-up) I
- CAN communication is normally performed with other units
- Each control with BCM is operating properly
J
CAN communication sleep mode (CAN sleep)
- CAN transmission is stopped
- Control with BCM only is operating
K
Low power consumption mode (BCM sleep)
- Low power consumption control is active
- CAN transmission is stopped
L
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of the each switches changes from 10 ms interval to 20 ms interval.
BCS
Sleep mode activation
• BCM receives the sleep-ready signal (ready) from IPDM E/R and combination meter via CAN communica-
tion. N
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful-
filled.
• Each unit stops the transmission of CAN communication with the sleep wake up signal. BCM is in CAN com-
munication sleep mode. O
• BCM is in the low power consumption mode and perform the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
P

Sleep condition
CAN sleep condition BCM sleep condition
• Receiving the sleep-ready signal (ready) from all units
• Ignition switch: OFF
• Vehicle security system alarm: No operation
• Warning lamp: No operation
• Warning chime: No operation
• Stop lamp switch: OFF The controls only BCM are completed.
• Key switch status: No change for 2 seconds (Interior room lamp battery saver: Time out etc.)
• Hazard warning lamp: No operation
• Exterior lamp: OFF
• Door lock status: No change for 2 seconds
• CONSULT-III communication status: No communication
• Door switch status: No change for 2 seconds
Wake-up operation
• BCM transmits sleep wake up signal (wake up) to each unit when any condition listed below is established,
and then goes into normal mode from low power consumption mode.
• Each unit starts transmissions with CAN communication by receiving sleep wake up signals. Each unit trans-
mits wake up signals to BCM with CAN communication to convey the start of CAN communication.
Wake-up condition
BCM wake-up condition
• Ignition switch: OFF → ACC or ON
• Stop lamp switch: ON (Depress brake pedal)
• Any door switch: OFF → ON
• Lighting switch: OFF → 1ST or PASS
• Hazard switch: OFF → ON
• Remote keyless entry receiver: Receiving
ALMIA0302ZZ
1. Steering column (view with instru- 2. BCM M18, M19, M20 3. Combination meter M24
ment panel removed)
4. IPDM E/R

DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000003789011
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
D
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to BCS-49, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification. F
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
I
BCM BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
K
Remote keyless entry system MULTI REMOTE ENT × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × × L
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Combination switch COMB SW × BCS
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
N
RAP (retained accessory power) RETAINED PWR × × ×
Signal buffer system SIGNAL BUFFER × ×
TPMS (tire pressure monitoring sys- O
AIR PRESSURE MONITOR × × ×
tem)
Vehicle security system PANIC ALARM ×
P
BCM
BCM : CONSULT-III Function (BCM - BCM) INFOID:0000000003789012
WORK SUPPORT

Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) INFOID:0000000003789013
WORK SUPPORT
Work Item Description

• ON
DOOR LOCK-UNLOCK SET
• OFF
• ON
ANTI-LOCK OUT SET
• OFF
• SHIFT OUT OF P
AUTOMATIC DOOR LOCK SELECT
• VH SPD
• MODE1
• MODE2
AUTOMATIC DOOR UNLOCK SE- • MODE3
LECT • MODE4
• MODE5
• MODE6
AUTOMATIC LOCK/UNLOCK SE- • ON
LECT • OFF
DATA MONITOR
Monitor Item
Description
[Unit}
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position
KEY ON SW [ON/OFF] Indicates condition of key switch
CDL LOCK SW [ON/OFF] Indicates condition of door lock and unlock switch
CDL UNLOCK SW [ON/OFF] Indicates condition of door lock and unlock switch
DOOR SW-DR [ON/OFF] Indicates condition of front door switch LH
DOOR SW-AS [ON/OFF] Indicates condition of front door switch RH
DOOR SW-RR [ON/OFF] Indicates condition of rear door switch RH
DOOR SW-RL [ON/OFF] Indicates condition of rear door switch LH
KEY CYL LK-SW [ON/OFF] Indicates condition of lock signal from door key cylinder switch
KEY CYL UN-SW [ON/OFF] Indicates condition of unlock signal from door key cylinder switch
KEYLESS LOCK [ON/OFF] Indicates condition of lock signal from keyfob
KEYLESS UNLOCK [ON/OFF] Indicates condition of unlock signal from keyfob
ACTIVE TEST
Test Item Description

This test is able to check door lock operation [ALL LOCK/ALL UNLOCK/DR UNLOCK/
DOOR LOCK
OTHER UNLOCK].
REAR WINDOW DEFOGGER

REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000003789014
DATA MONITOR

Monitor Item A
Description
[Unit]
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position
IGN ACC SW [ON/OFF] Indicates condition of ignition switch in ACC position B
REAR DEF SW [ON/OFF] Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch
BUZZER C
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000003789015
DATA MONITOR D
Monitor Item
Description
[Unit] E
IGN ON SW [ON/OFF] Ignition switch (ON) status judged by ignition power supply input
KEY ON SW [ON/OFF] Key switch status
F
DOOR SW -DR [ON/OFF] Front door switch (driver side) status judged by BCM
Lighting switch status judged by the lighting switch signal read with combination switch reading func-
LIGHT SW 1ST [ON/OFF]
tion
G
BUCKLE SW [ON/OFF] Seat belt buckle switch status
ACTIVE TEST
H
LIGHT WARN ALM The light reminder warning operation can be checked by operating the relevant function (On/Off).
I
IGN KEY WARN ALM The key reminder warning operation can be checked by operating the relevant function (On/Off).
SEAT BELT WARN TEST The seat belt warning operation can be checked by operating the relevant function (On/Off).
DOOR WARNING IND The door open warning operation can be checked by operating the relevant function (On/Off). J
INT LAMP
INT LAMP : CONSULT-III Function (BCM - INT LAMP) INFOID:0000000003789016 K
WORK SUPPORT
L
BCS
P
JPLIA0093GB
Work Item Setting item Setting

ON* With the interior room lamp timer function
SET I/L D-UNLCK INTCON
OFF Without the interior room lamp timer function

MODE 1 0.5 sec.
MODE 2* 1 sec.
ROOM LAMP ON TIME SET MODE 3 2 sec. Sets the interior room lamp gradual brightening time.
MODE 4 3 sec.
MODE 5 0 sec.
MODE 1 0.5 sec.
MODE 2 1 sec.
ROOM LAMP OFF TIME SET MODE 3 2 sec. Sets the interior room lamp gradual dimming time.
MODE 4* 3 sec.
MODE 5 0 sec.
* : Initial setting
DATA MONITOR
Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY ON SW [ON/OFF] The switch status input from key switch
DOOR SW-DR [ON/OFF] The switch status input from front door switch LH
DOOR SW-AS [ON/OFF] The switch status input from front door switch RH
DOOR SW-RR [ON/OFF] The switch status input from rear door switch RH
DOOR SW- RL [ON/OFF] The switch status input from rear door switch LH
KEY CYL LK-SW [ON/OFF] Lock switch status input from door lock and unlock switch
KEY CYL UN-SW [ON/OFF] Lock switch status input from door lock and unlock switch
CDL LOCK SW [ON/OFF] Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF] Unlock switch status input from door lock and unlock switch
Lock signal status received from remote keyless entry receiver (integrated in the
KEYLESS LOCK [ON/OFF]
BCM)
Unlock signal status received from remote keyless entry receiver (integrated in the
KEYLESS UNLOCK [ON/OFF]
BCM)
ACTIVE TEST
Test Item Operation Description

ON Outputs the interior room lamp control signal to turn the interior room lamps ON.
INT LAMP
OFF Stops the interior room lamp control signal to turn the interior room lamps OFF.
Outputs the ignition keyhole illumination control signal to turn the ignition keyhole il-
ON
lumination lamp ON.
IGN ILLUM
Stops the ignition keyhole illumination control signal to turn the ignition keyhole illu-
OFF
mination lamp OFF.
ON Outputs the step lamp control signal to turn the step lamps ON.
STEP LAMP TEST
OFF Stops the step lamp control signal to turn the step lamps OFF.
MULTIREMOTE ENT
MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)
INFOID:0000000004190596
WORK SUPPORT

Test Item Description A

REMO CONT ID REGIST Keyfob ID code can be registered.
REMO CONT ID ERASUR Keyfob ID code can be erased.
REMO CONT ID CONFIR It can be checked whether keyfob ID code is registered or not in this mode.
B
HORN CHIRP SET Horn chirp function mode can be changed in this mode. The function mode will be changed when
"CHANG SETT" on CONSULT-III screen is touched.
C
HAZARD LAMP SET Hazard lamp function mode can be changed in this mode. The function mode will be changed when
Hazard and horn reminder mode can be changed in this mode. The reminder mode will be changed
MULTI ANSWER BACK SET D
when “CHANG SETT” on CONSULT-III screen is touched.
Auto locking function mode can be changed in this mode. The function mode will be changed when
AUTO LOCK SET
E
Panic alarm operation mode can be changed in this mode. The operation mode will be changed when
PANIC ALRM SET
Keyless power window down (open) operation mode can be changed in this mode. The operation
PW DOWN SET F
mode will be changed when "CHANG SETT" on CONSULT-III screen is touched.
Hazard and horn reminder mode

MODE 1 MODE 2
MODE 3 MODE 4 MODE 5 MODE 6 G
(C mode) (S mode)
Keyfob
Lock Unlock Lock Unlock Lock Unlock Lock Unlock Lock Unlock Lock Unlock
operation
Hazard warning
H
Twice Once Twice — — — Twice Once Twice — — Once
lamp flash
Horn sound Once — — — — — — — Once — Once —
I
Auto locking function mode
MODE 1 MODE 2 MODE 3
Auto locking function 5 minutes Nothing 1 minute
J
Panic alarm operation mode
Keyfob operation 0.5 seconds Nothing 1.5 seconds K
Keyless power window down operation mode
L
Keyfob operation 3 seconds Nothing 5 seconds
DATA MONITOR
BCS
Monitored Item Description
DOOR SW-AS Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH. N
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch LH.
O
KEY ON SW Indicates [ON/OFF] condition of key switch.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position. P
KEYLESS PANIC Indicates [ON/OFF] condition of panic signal from keyfob.
KEYLESS UNLOCK Indicates [ON/OFF] condition of unlock signal from keyfob.
KEYLESS LOCK Indicates [ON/OFF] condition of lock signal from keyfob.
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from door key cylinder switch.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from door key cylinder switch.

Monitored Item Description
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from lock/unlock switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from lock/unlock switch.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
RKE LCK-UNLCK Indicates [ON/OFF] condition of lock/unlock signal at the same time from keyfob.
RKE KEEP UNLK Indicates [ON/OFF] condition of unlock signal from keyfob.
ACTIVE TEST

FLASHER This test is able to check right and left hazard reminder operation. The right hazard lamp turns on
when “RH” on CONSULT-III screen is touched and the left hazard lamp turns on when "LH" on CON-
SULT-III screen is touched.
POWER WINDOW DOWN This test is able to check power window down operation. The windows are lowered when “ON” on
CONSULT-III screen is touched.
HORN This test is able to check panic alarm and horn reminder operations. The alarm activate for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
DOOR LOCK This test is able to check door lock operation. The doors lock and unlock based on the item on CON-
SULT-III screen touched.
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000003789018
WORK SUPPORT

ON* With the exterior lamp battery saver function
BATTERY SAVER SET
OFF Without the exterior lamp battery saver function
MODE1* Normal
CUSTOM A/LIGHT SET- MODE2 More sensitive setting than normal setting (Turns ON earlier than normal operation.)
TING MODE3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
MODE1* 45 sec.
Without the func-
MODE2
tion
MODE3 30 sec.
MODE4 60 sec. Sets delay timer function timer operation time
ILL DELAY SET
(All doors closed)
MODE5 90 sec.
MODE6 120 sec.
MODE7 150 sec.
MODE8 180 sec.
*: Initial setting
DATA MONITOR
Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)

Monitor Item
Description
[Unit] A
HI BEAM SW [ON/OFF]
H/L SW POS [ON/OFF]
B
LIGHT SW 1ST [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
PASSING SW [ON/OFF]
AUTO LIGHT SW [ON/OFF] C
FR FOG SW [ON/OFF]
DOOR SW-DR [ON/OFF] The switch status input from front door switch LH
D
AUT LIGHT SYS [ON/OFF] Auto light system status that BCM judges from the vehicle condition
ACTIVE TEST
E
Transmits the position light request signal to IPDM E/R with CAN com-
ON
TAIL LAMP munication to turn the tail lamp ON. F
OFF Stops the tail lamp request signal transmission.
Transmits the high beam request signal with CAN communication to turn
HI
the headlamp (HI). G
HEAD LAMP Transmits the low beam request signal with CAN communication to turn
LO
the headlamp (LO).
OFF Stops the high & low beam request signal transmission. H
Transmits the front fog lights request signal to IPDM E/R with CAN com-
ON
FR FOG LAMP munication to turn the front fog lamp ON.
OFF Stops the front fog lights request signal transmission. I
Transmits the day time running light request signal to IPDM E/R with
ON
DAYTIME RUNNING LIGHT CAN communication to turn the each lamps ON.
J
OFF Stops the day time running light request signal transmission.
WIPER
K
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000003789019
WORK SUPPORT L
Setting
Work Item Description
Item
BCS
With vehicle speed
ON*
WIPER SPEED (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
SETTING Without vehicle speed
OFF N
(Front wiper intermittent time linked with the wiper intermittent dial position)
*: Factory setting
DATA MONITOR O
Monitor Item
Description
[Unit]
P
IGN ON SW [ON/OFF] Ignition switch ON status judged from ignition power supply
FR WIPER HI [ON/OFF]
FR WIPER LOW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
FR WIPER INT [ON/OFF]
FR WASHER SW [ON/OFF]
INT VOLUME [1 - 7] Each switch status that BCM judges from the combination switch reading function

Monitor Item
Description
[Unit]
Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
FR WIPER STOP [ON/OFF]
tion
The value of the vehicle speed signal received from combination meter with CAN com-
VEHICLE SPEED [km/h]
munication
ACTIVE TEST

Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
HI
erate the front wiper HI operation.
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
LO
FR WIPER operate the front wiper LO operation.
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
INT
operate the front wiper INT operation.
OFF Stops transmitting the front wiper request signal to stop the front wiper operation.
RISE UP WIPER ON Outputs the voltage to operate the rear wiper motor.
TEST OFF Stops the voltage to stop.
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000003789020
DATA MONITOR
Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF] The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
BRAKE SW [ON/OFF] The switch status input from the brake switch
ACTIVE TEST

RH Outputs the voltage to turn the right side turn signal lamps ON.
FLASHER LH Outputs the voltage to turn the left side turn signal lamps ON.
OFF Stops the voltage to turn the turn signal lamps OFF.
AIR CONDITIONER
AIR CONDITIONER : CONSULT-III Function (BCM - AUTO AIR CONDITIONER)
INFOID:0000000003789021
DATA MONITOR
Monitor Item
Contents
[Unit]
Display [ignition switch position (On)/(Off), ACC position (Off)] status as judged from ignition
IGN ON SW [ON/OFF]
switch signal
FAN ON SIG [ON/OFF] Display [FAN (On)/FAN (Off)] status as judged form blower fan motor switch signal
AIR COND SW [ON/OFF] Display [COMP (On)/COMP (Off)] status as judged form air conditioner switch signal

COMB SW
A
COMB SW : CONSULT-III Function (BCM - COMB SW) INFOID:0000000003789022
DATA MONITOR B
Monitor Item
Description
[Unit]
C
TURN SIGNAL R Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
[OFF/ON] reading function
TURN SIGNAL L Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch D
HI BEAM SW Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
E
HEADLAMP SW1 Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function
HEADLAMP SW2 Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
F
LIGHT SW 1ST Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
G
PASSING SW Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
AUTO LIGHT SW Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
H
FR FOG SW Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
I
FR WIPER HI Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
FR WIPER LOW Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
[OFF/ON] switch reading function J
FR WIPER INT Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
FR WASHER SW Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
K
INT VOLUME Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
[1 - 7] function L
IMMU
IMMU : CONSULT-III Function (BCM - IMMU) INFOID:0000000003789023
BCS
DATA MONITOR
N
Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Indicates condition of ignition switch in ON position. O
ACTIVE TEST
P
THEFT IND This test is able to check security indicator operation [ON/OFF].
BATTERY SAVER

BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) INFOID:0000000003789024
WORK SUPPORT
Work Item Setting Item Setting

MODE 1* 15 min. Sets the interior room lamp battery saver timer operating
ROOM LAMP TIMER SET
MODE 2 30 min. time.
*: Initial setting
DATA MONITOR
Monitor Item
Description
[Unit]
IGN ON SW [ON/OFF] Ignition switch (ON) status judges from IGN signal (ignition power supply)
KEY ON SW [ON/OFF] The switch status input from key switch
DOOR SW-DR [ON/OFF] The switch status input from front door switch (driver side)
DOOR SW-AS [ON/OFF] The switch status input from front door switch (passenger side)
DOOR SW-RR [ON/OFF] The switch status input from rear door switch RH
DOOR SW- RL [ON/OFF] The switch status input from rear door switch LH
KEY CYL LK-SW [ON/OFF] Lock switch status input from door key cylinder switch
KEY CYL UN-SW [ON/OFF] Unlock switch status input from door key cylinder switch
CDL LOCK SW [ON/OFF] Lock switch status input from door lock and unlock switch
CDL UNLOCK SW [ON/OFF] Unlock switch status input from door lock and unlock switch
Lock signal status received from remote keyless entry receiver (integrated in the
KEYLESS LOCK [ON/OFF]
BCM)
Unlock signal status received from remote keyless entry receiver (integrated in the
KEYLESS UNLOCK [ON/OFF]
BCM)
ACTIVE TEST

OFF Cuts the interior room lamp power supply to turn interior room lamps OFF.
BATTERY SAVER
ON Outputs the interior room lamp power supply to turn interior room lamps ON.*
*: Each lamp switch is in ON position.
RETAINED PWR
RETAINED PWR : CONSULT-III Function (BCM - RETAINED PWR) INFOID:0000000003789025
Data monitor
Monitor Item
Description
[Unit]
DOOR SW-DR [ON/OFF] Indicates condition of front door switch LH.
DOOR SW-AS [ON/OFF] Indicates condition of front door switch RH.
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER) INFOID:0000000003789026
DATA MONITOR

Monitor Item A
Description
[Unit]
OIL PRESS SW [ON/OFF] Displays the status of oil pressure switch received from IPDM E/R via CAN communication.
B
ACTIVE TEST

C
OFF OFF
OIL PRESSURE SW BCM transmits the oil pressure switch signal to the combination meter via CAN communica-
ON
tion, which operates the oil pressure gauge in the combination meter.
D
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : Diagnosis Description INFOID:0000000003789027
E
DESCRIPTION
During driving, the TPMS receives the signal transmitted from the transmitter installed in each wheel, when
F
the tire pressure becomes low. The control unit (BCM) of this system has pressure judgment and trouble diag-
nosis functions.
When the TPMS detects low inflation pressure or another unusual symptom, the warning lamps in the combi-
nation meter comes on. G
SELF DIAGNOSTIC PROCEDURE (WITH CONSULT-III)
With CONSULT-III
H
• Touch “SELF-DIAG RESULTS” display to show malfunction experienced since the last erasing operation.
Refer to BCS-49, "DTC Index".
SELF DIAGNOSTIC PROCEDURE (WITHOUT CONSULT-III) I
Without CONSULT-III
To start the self-diagnostic results mode, ground terminal of the tire pressure warning check connector. The
malfunction location is indicated by the warning lamp flashing.
J
SEIA0745E
BCS
NOTE:
When the low tire warning lamp flashes 5 Hz and continues repeating it, the system is normal.
N
Flickering
Items Diagnostic items detected when··· Check item
pattern
15 Tire pressure value (Front LH) Front LH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less. O
16 Tire pressure value (Front RH) Front RH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less.
–
17 Tire pressure value (Rear RH) Rear RH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less.
18 Tire pressure value (Rear LH) Rear LH tire pressure drops to 181 kPa (1.8 kg/cm, 25.25 psi) or less. P
21 Transmitter no data (Front LH) Data from front LH transmitter can not be received.
22 Transmitter no data (Front RH) Data from front RH transmitter can not be received.
WT-33
23 Transmitter no data (Rear RH) Data from Rear RH transmitter can not be received.
24 Transmitter no data (Rear LH) Data from Rear LH transmitter can not be received.

Flickering
Items Diagnostic items detected when··· Check item
pattern
Transmitter checksum error
31 Checksum data from front LH transmitter is malfunctioning.
(Front LH)
32 Checksum data from front RH transmitter is malfunctioning.
(Front RH)
WT-33
33 Checksum data from rear RH transmitter is malfunctioning.
(Rear RH)
34 Checksum data from rear RH transmitter is malfunctioning.
(Rear LH)
Transmitter pressure data error
35 Air pressure data from front LH transmitter is malfunction.
(Front LH)
36 Air pressure data from front RH transmitter is malfunction.
(Front RH)
WT-33
37 Air pressure data from rear RH transmitter is malfunction.
(Rear RH)
38 Air pressure data from rear LH transmitter is malfunction.
(Rear LH)
Transmitter function code error
41 Function code data from front LH transmitter is malfunction.
(Front LH)
42 Function code data from front RH transmitter is malfunction.
(Front RH)
WT-32
43 Function code data from rear RH transmitter is malfunction.
(Rear RH)
44 Function code data from rear LH transmitter is malfunction.
(Rear LH)
Transmitter battery voltage low
45 Battery voltage of front LH transmitter drops.
(Front LH)
46 Battery voltage of front RH transmitter drops.
(Front RH)
WT-33
47 Battery voltage of rear RH transmitter drops.
(Rear RH)
48 Battery voltage of rear LH transmitter drops.
(Rear LH)
52 Vehicle speed signal error Speed signal is not detected. WT-33
54 Vehicle ignition signal Ignition signal is not detected. WT-33
No flicker- Tire pressure warning check
Tire pressure warning switch circuit is open. –
ing switch
ERASE SELF-DIAGNOSIS
With CONSULT-III
1. Perform applicable inspection of malfunctioning item and then repair or replace.
2. Turn ignition switch “ON” and select “SELF-DIAG RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULTIII.
3. Touch “ERASE” on CONSULT-III screen to erase memory.
Without CONSULT-III
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned “ON” and“OFF”.
• However, this information is erased by turning ignition switch “OFF” after performing self-diagnostic or by
erasing the memory using the CONSULT-III.
AIR PRESSURE MONITOR : CONSULT-III Function INFOID:0000000003789028
WORK SUPPORT MODE

ID Read
The registered ID number is displayed. A
ID Regist
Refer to WT-6, "ID Registration Procedure".
B
SELF-DIAG RESULTS MODE
Operation Procedure
Refer to BCS-49, "DTC Index". C
DATA MONITOR MODE
Screen of data monitor mode is displayed. Refer to BCS-36, "Reference Value".
NOTE: D
When malfunction is detected, CONSULT-III perform REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
ACTIVE TEST MODE E
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction may be different
from that displayed on CONSULT-III. F
TEST ITEM LIST
Test item Content G

WARNING LAMP This test is able to check to make sure that the warning lamp turns on.
ID REGIST WARNING This test is able to check to make sure that the buzzer sounds or the warning lamp turns on.
H
FLASHER This test is able to check to make sure that each turn signal lamp turns on.
HORN This test is able to check to make sure that the horn sounds.
THEFT ALM I
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM) INFOID:0000000003789029
J
WORK SUPPORT
Work Item Description K

Vehicle security function mode can be changed in this mode.
SECURITY ALARM SET • ON: Vehicle security function is ON.
• OFF: Vehicle security function is OFF.
L
BCS

U1000 CAN COMM CIRCUIT
< COMPONENT DIAGNOSIS > [BCM]
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description INFOID:0000000003789030
Refer to LAN-4, "System Description".

CAN Communication Signal Chart. Refer to LAN-59, "CAN Communication Signal Chart".
DTC Logic INFOID:0000000003789031
DTC DETECTION LOGIC
CONSULT-III display
DTC DTC Detection Condition Possible cause
description
Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
• Transmission
When BCM cannot communicate CAN com-
• Receiving (ECM)
U1000 CAN COMM CIRCUIT munication signal continuously for 2 sec-
• Receiving (METER/M&A)
onds or more.
• Receiving (TCM)
• Receiving (MULTI AV)
• Receiving (IPDM E/R)
Diagnosis Procedure INFOID:0000000003789032
1. PERFORM SELF DIAGNOSTIC

1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is “CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-38, "Intermittent Incident".

U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
A
DTC Logic INFOID:0000000003789033
DTC DETECTION LOGIC B
CONSULT-III display de-

DTC DTC Detection Condition Possible cause
scription C
When detecting error during the initial diagnosis of CAN control-
U1010 CONTROL UNIT (CAN) BCM
ler of BCM.

D
1. REPLACE BCM
E
When “DTC: U1010” is detected, replace BCM.
>> Replace BCM. Refer to BCS-53, "Removal and Installation". F

Special Repair Requirement INFOID:0000000003789035
1. ADDITIONAL SERVICE WHEN REPLACING BCM G
H
>> Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
Requirement".
BCS

POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSES AND FUSIBLE LINK

Check that the following fuses and fusible link are not blown.
Terminal No. Signal name Fuses and fusible link No.

57 22 (15A)
Battery power supply
70 F (50A)
11 Ignition ACC or ON 4 (10A)
38 Ignition ON or START 59 (10A)
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Terminals Power Voltage (V) (Ap-

Connector Condition
(+) (-) source prox.)
Ignition
ACC
switch
11 Ground power Battery voltage
ACC or
supply
M18 ON
LIIA2415E
Ignition Ignition
38 Ground power switch ON Battery voltage
supply or START
Battery Ignition
57 Ground power switch Battery voltage
supply OFF
M20
Battery Ignition
70 Ground power switch Battery voltage
supply OFF
Is the measurement value normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M20 67 Yes
Does continuity exist?
YES >> Inspection End.
LIIA0915E

COMBINATION SWITCH INPUT CIRCUIT
A
1. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN B

2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi- C
nation switch harness connector.
BCM Combination switch D

System Continuity
Connector Terminal Connector Terminal
INPUT 1 6 6
E
INPUT 2 5 7
M18 M28 ALMIA0275ZZ
INPUT 3 4 10 Yes
(A) (B)
INPUT 4 3 9 F
INPUT 5 2 8
YES >> GO TO 2 G
2. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT H
Check for continuity between BCM harness connector and ground.
BCM I
System Continuity
Connector Terminal
INPUT 1 6
J
INPUT 2 5 Ground
INPUT 3 M18 4 No
INPUT 4 3 K
INPUT 5 2 ALMIA0276ZZ

YES >> Repair or replace harness. L
NO >> GO TO 3
3. CHECK BCM OUTPUT VOLTAGE BCS
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector and ground.
N
Terminals
(+) (−) Voltage O
System
BCM (Approx.)
Connector Terminal
INPUT 1 6 P
Ground ALMIA0277ZZ
INPUT 2 5
Refer to BCS-
INPUT 3 M18 4 36, "Refer-
ence Value".
INPUT 4 3
INPUT 5 2
Is the measurement value normal?

YES >> GO TO 4
NO >> Replace BCM. Refer to BCS-53, "Removal and Installation".
4. CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-34, "Description".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-53, "Removal and Installation".
NO >> Replace the combination switch (applicable parts). Refer to EXL-142, "Removal and Installation".
1. ADDITIONAL SERVICE WHEN REPLACING BCM
Requirement".

COMBINATION SWITCH OUTPUT CIRCUIT
COMBINATION SWITCH OUTPUT CIRCUIT
A
1. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN B

2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi- C
nation switch harness connector.
BCM Combination switch D

System Continuity
Connector Terminal Connector Terminal
OUTPUT 1 36 1
E
OUTPUT 2 35 2
M18 M28 ALMIA0278ZZ
OUTPUT 3 34 3 Yes
(A) (B)
OUTPUT 4 33 4 F
OUTPUT 5 32 5
YES >> GO TO 2 G
2. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT H
Check for continuity between BCM harness connector and ground.
BCM I
System Continuity
Connector Terminal
OUTPUT 1 36
J
OUTPUT 2 35 Ground
OUTPUT 3 M18 34 No
OUTPUT 4 33 K
OUTPUT 5 32 ALMIA0279ZZ

YES >> Repair or replace harness. L
NO >> GO TO 3
3. CHECK COMBINATION SWITCH BCS
Check combination switch. Refer to BCS-34, "Description".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-53, "Removal and Installation". N
NO >> Replace combination switch (applicable parts). Refer to EXL-142, "Removal and Installation".
O
1. ADDITIONAL SERVICE WHEN REPLACING BCM
P
Requirement".

COMBINATION SWITCH
COMBINATION SWITCH
Description INFOID:0000000003789041
COMBINATION SWITCH MATRIX

Combination switch consists of INPUT circuit and OUTPUT circuit.
Combination switch circuit
LIIA1325E
Combination switch INPUT-OUTPUT system list

System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 — — HEADLAMP 2 HI BEAM
INPUT 4 — INT VOLUME 3 AUTO LIGHT — TAIL LAMP
INPUT 5 INT VOLUME 2 — — FR FOG —
NOTE:
Headlamp has a dual system switch.
1. CHECK LIGHT & TURN SIGNAL SWITCH

Check operation with normal light & turn signal switch installed.
Does it operate normally?
YES >> Replace light & turn signal switch. Refer to EXL-142, "Removal and Installation".
NO >> GO TO 2
2. CHECK WIPER & WASHER SWITCH
Check operation with normal wiper & washer switch installed.
Does it operate normally?
YES >> Replace wiper & washer switch. Refer to WW-63, "Wiper and Washer Switch".

COMBINATION SWITCH
NO >> GO TO 3
3. CHECK SWITCH BASE (SPIRAL CABLE) A
Check operation with normal switch base (spiral cable) installed.

Does it operate normally? B
YES >> Replace switch base (spiral cable). Refer to ST-23, "Disassembly and Assembly".
NO >> Combination switch is normal.
C
BCS

BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS > [BCM]
ECU DIAGNOSIS
Reference Value INFOID:0000000003789043
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status

A/C switch OFF OFF
AIR COND SW
A/C switch ON ON
Outside of the room is dark OFF
AUT LIGHT SYS
Outside of the room is bright ON
Lighting switch OFF OFF
AUTO LIGHT SW
Lighting switch AUTO ON
Door lock/unlock switch does not operate OFF
CDL LOCK SW
Press door lock/unlock switch to the LOCK side ON
Door lock/unlock switch does not operate OFF
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side ON
Front door RH closed OFF
DOOR SW-AS
Front door RH opened ON
Front door LH closed OFF
DOOR SW-DR
Front door LH opened ON
Rear door LH closed OFF
DOOR SW-RL
Rear door LH opened ON
Rear door RH closed OFF
DOOR SW-RR
Rear door RH opened ON
Engine stopped OFF
ENGINE RUN
Engine running ON
Front fog lamp switch OFF OFF
FR FOG SW
Front fog lamp switch ON ON
Front washer switch OFF OFF
FR WASHER SW
Front washer switch ON ON
Front wiper switch OFF OFF
FR WIPER LOW
Front wiper switch LO ON
FR WIPER HI
Front wiper switch HI ON
FR WIPER INT
Front wiper switch INT ON
Any position other than front wiper stop position OFF
FR WIPER STOP
Front wiper stop position ON
When hazard switch is not pressed OFF
HAZARD SW
When hazard switch is pressed ON
Lighting switch OFF OFF
LIGHT SW 1ST
Lighting switch 1st ON
Headlamp switch OFF OFF
HEADLAMP SW1
Headlamp switch 1st ON

Monitor Item Condition Value/Status
A
Headlamp switch OFF OFF
HEADLAMP SW2
Headlamp switch 1st ON
High beam switch OFF OFF B
HI BEAM SW
High beam switch HI ON
NOTE:
H/L WASH SW OFF
The item is indicated, but not monitored C
Ignition switch OFF or ACC OFF
IGN ON SW
Ignition switch ON ON
D
Ignition switch OFF or ACC OFF
IGN SW CAN
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7 E
Key is removed from key cylinder OFF
KEY ON SW
Key is inserted to key cylinder ON
LOCK button of key fob is not pressed OFF F
KEYLESS LOCK
LOCK button of key fob is pressed ON
UNLOCK button of key fob is not pressed OFF
KEYLESS UNLOCK G
UNLOCK button of key fob is pressed ON
• Ignition switch OFF or ACC
OFF
OIL PRESS SW • Engine running H
Other than lighting switch PASS OFF
PASSING SW
Lighting switch PASS ON I
Rear window defogger switch OFF OFF
REAR DEF SW
Rear window defogger switch ON ON
J
RKE LOCK AND UN- NOTE: OFF
LOCK The item is indicated, but not monitored ON
Lighting switch OFF OFF K
TAIL LAMP SW
Lighting switch 1ST ON
Turn signal switch OFF OFF
TURN SIGNAL L L
Turn signal switch LH ON
Turn signal switch OFF OFF
TURN SIGNAL R
Turn signal switch RH ON BCS
VEHICLE SPEED While driving Equivalent to speedometer reading

Terminal Layout INFOID:0000000003789044
LIIA2443E
Physical Values INFOID:0000000003789045

Signal Measuring condition A

Wire Reference value or waveform
Terminal Signal name input/ Ignition
color Operation or condition (Approx.)
output switch
Door is locked (SW OFF) Battery voltage B
Ignition keyhole illumi-
1 BR/W Output OFF
nation Door is unlocked (SW OFF) 0V
Combination switch Lighting, turn, wiper OFF

2 SB Input ON
input 5 Wiper dial position 4 D
SKIA5291E
E

F
3 G/Y Input ON
input 4 Wiper dial position 4
G
SKIA5292E

4 Y Input ON
input 3 Wiper dial position 4
I
SKIA5291E
Combination switch J
5 G/B
input 2
Lighting, turn, wiper OFF K

Input ON
Combination switch Wiper dial position 4
6 V
input 1
SKIA5292E L
Rear window defogger switch
0V
Rear window defogger ON
9 Y/B Input ON BCS
switch (Crew Cab) Rear window defogger switch
5V
OFF
Ignition switch (ACC ACC or
11 O Input Ignition switch ACC or ON Battery voltage
or ON) ON N
Front door switch RH
(All)
ON (open) 0V
Rear door switch low- O
12 R/L Input OFF
er RH (King Cab)
Rear door switch up-
OFF (closed) Battery voltage
per RH (King Cab) P
Rear door switch RH ON (open) 0V
13 GR Input OFF
(Crew Cab) OFF (closed) Battery voltage
Tire pressure warning
15 L/W Input OFF — 5V
check connector

Signal Measuring condition

output switch
Remote keyless entry
18 P receiver and optical Output OFF — 0V
sensor (ground)
Remote keyless entry

19 V/W receiver (power sup- Output OFF Ignition switch OFF
ply)
LIIA1893E
Stand-by (keyfob buttons re-

leased)
Remote keyless entry LIIA1894E

20 G/W Input OFF
receiver (signal)
When remote keyless entry

receiver receives signal from
keyfob (keyfob buttons
pressed)
LIIA1895E
Just after turning ignition switch

OFF → ON: Pointer of tester should
21 G NATS antenna amp. Input Ignition switch (OFF → ON)
ON move for approx. 1 second, then
return to battery voltage.
Ignition switch ON or power

22 G BUS — —
window timer operates
PIIA2344E
Security indicator Goes OFF → illuminates (Ev-

23 G/O Output OFF Battery voltage → 0V
lamp ery 2.4 seconds)
Just after turning ignition switch
OFF → ON: Pointer of tester should
25 BR NATS antenna amp. Input Ignition switch (OFF → ON)
ON move for approx. 1 second, then
return to battery voltage.
Compressor ON sig- A/C switch OFF 5V

27 W/R Input ON
nal A/C switch ON 0V
Front blower motor OFF Battery voltage
28 L/R Front blower monitor Input ON
Front blower motor ON 0V
ON 0V
29 W/B Hazard switch Input OFF
OFF 5V
Cargo lamp switch ON 0
31 P/L Cargo lamp switch Input OFF
Cargo lamp switch OFF Battery voltage
Revision: November 2008 B C S - 4 0 2009 Titan


Wire Reference value or waveform A
output switch

32 R/G Output ON
output 5 Wiper dial position 4 C
SKIA5291E
D
Combination switch Lighting, turn, wiper OFF E

33 R/Y Output ON
output 4 Wiper dial position 4
F
SKIA5292E
G
34 L Output ON
output 3 Wiper dial position 4
H
SKIA5291E
Combination switch I
35 O/B
output 2
Lighting, turn, wiper OFF

Output ON
Wiper dial position 4 J
Combination switch
36 R/W
output 1
SKIA5292E K
Key switch and key Key inserted Battery voltage
37 B/R Input OFF
lock solenoid Key inserted 0V
L
38 W/L Ignition switch (ON) Input ON — Battery voltage
39 L CAN-H — — — —
40 P CAN-L — — — — BCS
Front door switch LH
(All)
ON (open) 0V
Rear door switch low- N
47 SB Input OFF
er LH (King Cab)
Rear door switch up-
OFF (closed) Battery voltage
per LH (King Cab)
O
Rear door switch LH ON (open) 0V
48 R/Y Input OFF
(Crew Cab) OFF (closed) Battery voltage
Cargo bed lamp con- Cargo lamp switch (ON) 0V P

50 R/Y Output OFF
trol Cargo lamp switch (OFF) Battery voltage


output switch
Trailer turn signal

51 G/Y Output ON Turn right ON
(right)
SKIA3009J
52 G/B Trailer turn signal (left) Output ON Turn left ON
SKIA3009J
30 minutes after ignition

OFF 0V
56 R/G Battery saver output Output switch is turned OFF
ON — Battery voltage
57 Y/R Battery power supply Input OFF — Battery voltage
When optical sensor is illumi-
3.1V or more
nated
58 W/R Optical sensor Input ON
When optical sensor is not illu-
0.6V or less
minated
Front door lock as- OFF (neutral) 0V
59 G sembly LH actuator Output OFF
(unlock) ON (unlock) Battery voltage
60 G/B Turn signal (left) Output ON Turn left ON
SKIA3009J
61 G/Y Turn signal (right) Output ON Turn right ON
SKIA3009J
ON (any door open) 0V

62 R/W Step lamp LH and RH Output OFF
OFF (all doors closed) Battery voltage
Interior room/map Any door ON (open) 0V

63 L Output OFF
lamp switch OFF (closed) Battery voltage
All door lock actuators OFF (neutral) 0V

65 V Output OFF
(lock) ON (lock) Battery voltage
Front door lock actua- OFF (neutral) 0V
tor RH and rear door
66 G/Y Output OFF
lock actuators LH/RH ON (unlock) Battery voltage
(unlock)


Wire Reference value or waveform A
output switch
67 B Ground Input ON — 0V
B
Ignition switch ON Battery voltage
Within 45 seconds after igni-
Battery voltage
tion switch OFF
C
Power window power More than 45 seconds after ig-
68 W/L Output — 0V
supply (RAP) nition switch OFF
When front door LH or RH is
D
open or power window timer 0V
operates
Power window power
69 W/R Output — — Battery voltage E
supply
70 W/B Battery power supply Input OFF — Battery voltage
BCS

Wiring Diagram INFOID:0000000003789046
ABMWA0020GB

BCS
ABMWA0021GB

ABMWA0022GB

BCS
ABMIA0027GB

ABMIA0028GB
Fail Safe INFOID:0000000004193507
Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.

Display contents of CONSULT Fail-safe Cancellation A

When the BCM re-establishes communication with the other mod-
U1000: CAN COMM CIRCUIT Inhibit engine cranking
ules.
U1010: CONTROL UNIT (CAN) Inhibit engine cranking When the BCM re-start communicating with the other modules. B
DTC Inspection Priority Chart INFOID:0000000003789047
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority C
chart.
Priority DTC D
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP E
• B2191: DIFFERENCE OF KEY
2
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
F
• C1729: VHCL SPEED SIG ERR
3
• C1735: IGNITION SIGNAL
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
G
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL H
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL I
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
4 J
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL K
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL L
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL BCS
DTC Index INFOID:0000000003789048
NOTE: N
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again. O
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again. P

Tire pressure
CONSULT display Fail-safe monitor warning Reference page
lamp ON
No DTC is detected.
further testing — — —
may be required.
U1000: CAN COMM CIRCUIT — — BCS-28
U1010: CONTROL UNIT (CAN) — — BCS-29
B2190: NATS ANTTENA AMP — — SEC-17
B2191: DIFFERENCE OF KEY — — SEC-20
B2192: ID DISCORD BCM-ECM — — SEC-21
B2193: CHAIN OF BCM-ECM — — SEC-23
C1708: [NO DATA] FL — — WT-14
C1709: [NO DATA] FR — — WT-14
C1710: [NO DATA] RR — — WT-14
C1711: [NO DATA] RL — — WT-14
C1712: [CHECKSUM ERR] FL — — WT-16
C1713: [CHECKSUM ERR] FR — — WT-16
C1714: [CHECKSUM ERR] RR — — WT-16
C1715: [CHECKSUM ERR] RL — — WT-16
C1716: [PRESSDATA ERR] FL — — WT-18
C1717: [PRESSDATA ERR] FR — — WT-18
C1718: [PRESSDATA ERR] RR — — WT-18
C1719: [PRESSDATA ERR] RL — — WT-18
C1720: [CODE ERR] FL — — WT-16
C1721: [CODE ERR] FR — — WT-16
C1722: [CODE ERR] RR — — WT-16
C1723: [CODE ERR] RL — — WT-16
C1724: [BATT VOLT LOW] FL — — WT-16
C1725: [BATT VOLT LOW] FR — — WT-16
C1726: [BATT VOLT LOW] RR — — WT-16
C1727: [BATT VOLT LOW] RL — — WT-16
C1729: VHCL SPEED SIG ERR — — WT-19
C1735: IGNITION SIGNAL — — WT-20

COMBINATION SWITCH SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [BCM]
SYMPTOM DIAGNOSIS A
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000003789049
B
1. Perform the data monitor of CONSULT-III to check for any malfunctioning item.
2. Check the malfunction combinations. C
Malfunction item: ×
Data monitor item
D
HEADLAMP SW 1
HEADLAMP SW 2
AUTO LIGHT SW
FR WASHER SW
TURN SIGNAL R
TURN SIGNAL L
FR WIPER LOW
TAIL LAMP SW
FR WIPER INT
PASSING SW
FR WIPER HI
INT VOLUME
HI BEAM SW
FR FOG SW
Malfunction combination
× × × × A F
× × × × B
× × × C
× × × D G
× × E
× × F H
× × G
× × × H
× × × × I I
× × × × J
Combinations other than those above K
J
All Items L
If only one item is detected or the item is not applicable to the combinations A to L M
3. Identify the malfunctioning part from the agreed combination and repair or replace the part. K
Malfunction
Malfunctioning part Repair or replace L
combination
A Combination switch INPUT 1 circuit
B Combination switch INPUT 2 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
BCS
C Combination switch INPUT 3 circuit
part. Refer to BCS-31, "Diagnosis Procedure".
D Combination switch INPUT 4 circuit
E Combination switch INPUT 5 circuit N
F Combination switch OUTPUT 1 circuit
G Combination switch OUTPUT 2 circuit
Inspect the combination switch output circuit applicable to the malfunction- O
H Combination switch OUTPUT 3 circuit
ing part. Refer to BCS-33, "Diagnosis Procedure".
I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit P
Light and turn signal switch or front wip-
K Refer to BCS-34, "Description".
er and washer switch
L BCM Replace BCM. Refer to BCS-53, "Removal and Installation".
Light and turn signal switch or front wip-
M Replace the switch that cannot be operated.
er and washer switch

PRECAUTIONS
< PRECAUTION > [BCM]
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION-
ER" INFOID:0000000004109542
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

< ON-VEHICLE REPAIR > [BCM]
ON-VEHICLE REPAIR A
Removal and Installation INFOID:0000000003789050
B
BCM
Removal C
NOTE:
If possible, before removing BCM, retrieve current BCM configuration to use for reference when configuring
brand-new BCM after installation. Refer to BCS-4, "CONFIGURATION : Special Repair Requirement". D
1. Disconnect the battery negative terminal.
2. Remove the lower knee protector. Refer to IP-11, "Removal and Installation".
3. Remove the screw and release the BCM. E
4. Disconnect the connectors and then remove the BCM.
LEIA0068E
H
Installation
Installation is in the reverse order of removal.
NOTE: I
• When replacing BCM, it must be configured. Refer to BCS-4, "CONFIGURATION : Special Repair Require-
ment".
• When replacing BCM, perform initialization of NATS system and registration of all NATS ignition key IDs. J
Refer to SEC-6.
• When replacing BCM, perform ID registration procedure of low tire pressure warning system. Refer to WT-6,
"ID Registration Procedure".
K
BCS

Bcs

Uploaded by

Copyright:

Available Formats

Bcs

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bcs

Uploaded by

Copyright:

Available Formats

ELECTRICAL & POWER CONTROL

ADDITIONAL SERVICE WHEN REPLACING DOOR LOCK ..............................................................16

COMBINATION SWITCH READING SYSTEM MULTIREMOTE ENT : CONSULT-III Function

Revision: November 2008 BCS-1 2009 Titan

U1010 CONTROL UNIT (CAN) ......................... 29 PRECAUTIONS ................................................. 52

Revision: November 2008 BCS-2 2009 Titan

1. SAVING VEHICLE SPECIFICATION H

>> WORK END

CONFIGURATION : Description INFOID:0000000003788999

Revision: November 2008 BCS-3 2009 Titan

1. WRITING VEHICLE SPECIFICATION

When writing saved data>>GO TO 2

>> WORK END

MANUAL SETTING ITEM

>> WORK END

Revision: November 2008 BCS-4 2009 Titan

Revision: November 2008 BCS-5 2009 Titan

• BCM M18, M19, M20 (view with instrument panel removed)

Revision: November 2008 BCS-6 2009 Titan

System Description INFOID:0000000003789004

Revision: November 2008 BCS-7 2009 Titan

Combination switch INPUT-OUTPUT system list

COMBINATION SWITCH READING FUNCTION

Revision: November 2008 BCS-8 2009 Titan

Revision: November 2008 BCS-9 2009 Titan

Intermittent INT VOLUME switch ON/OFF status

Component Parts Location INFOID:0000000003789005

Revision: November 2008 BCS-10 2009 Titan

Revision: November 2008 BCS-11 2009 Titan

System Description INFOID:0000000003789007

Signal name Input Output Description

Revision: November 2008 BCS-12 2009 Titan

System Description INFOID:0000000003789009

Revision: November 2008 BCS-13 2009 Titan

Component Parts Location INFOID:0000000003789010

Revision: November 2008 BCS-14 2009 Titan

Revision: November 2008 BCS-15 2009 Titan

Work Item Description

Test Item Description

REAR WINDOW DEFOGGER

Revision: November 2008 BCS-16 2009 Titan

Work Item Setting item Setting

Revision: November 2008 BCS-17 2009 Titan

Test Item Operation Description

Revision: November 2008 BCS-18 2009 Titan

Test Item Description A

Hazard and horn reminder mode

Revision: November 2008 BCS-19 2009 Titan

Test Item Description

Work Item Setting item Setting

Revision: November 2008 BCS-20 2009 Titan

Revision: November 2008 BCS-21 2009 Titan

Test Item Operation Description

Test Item Operation Description

Revision: November 2008 BCS-22 2009 Titan

Revision: November 2008 BCS-23 2009 Titan

Work Item Setting Item Setting

Test Item Operation Description

Revision: November 2008 BCS-24 2009 Titan

Test Item Operation Description