How to read P&IDs - 8/1/2000 - Control Engineering Página 1 de 3

CE Asia CE China CE Poland CE Europe CE Russia Welcome JULIAN | Log out

HOME Industry Channels Re s o u r c e C e n te r M a g a zi n e N e w s le tt e r s RS S Di r e c t o r ie s J o bs U s e f u l L in ks M e d ia I n f o

How to read P&IDs

Dave Harrold, senior editor -- Control Engineering, 8/1/2000

Instrumentation detail varies with the degree of design complexity. For example, simplified or
conceptual designs, often called process flow diagrams, provide less detail than fully developed
piping and instrumentation diagrams (P&IDs). Being able to understand instrumentation symbols
appearing on diagrams means understanding ANSI/ISA's S5.1-1984 (R 1992) Instrumentation
symbols and identification standard. S5.1 that defines how each symbol is constructed using
graphical elements, alpha and numeric identification codes, abbreviations, function blocks, and
connecting lines.

Deciphering symbols

ISA S5.1 defines four graphical elements-discrete

instruments, shared control/display, computer
function, and programmable logic controller-and
groups them into three location categories (primary
location, auxiliary location, and field mounted).

Discrete instruments are indicated by circular

elements. Shared control/display elements are
circles surrounded by a square. Computer functions
are indicted by a hexagon and programmable logic
controller (PLC) functions are shown as a triangle
inside a square.

Adding a single horizontal bar across any of the four

graphical elements indicates the function resides in
the primary location category. A double line indicates
an auxiliary location, and no line places the device or
function in the field. Devices located behind a panel-
board in some other inaccessible location are shown
with a dashed horizontal line

Letter and number combinations appear inside each graphical element and letter combinations are
defined by the ISA standard. Numbers are user assigned and schemes vary with some companies
use of sequential numbering, others tie the instrument number to the process line number, and still
others adopt unique and sometimes unusual numbering systems.

The first letter defines the measured or initiating variables such as Analysis (A), Flow (F),
Temperature (T), etc. with succeeding letters defining readout, passive, or output functions such as
Indicator (I), Record (R), Transmit (T), and so forth.

Example shows the story

Referring to the Example P&ID diagram, FT 101 represents a field-mounted flow transmitter
connected via electrical signals (dotted line) to flow indicating controller FIC 101 located in a shared
control/display device. A square root extraction of the input signal is applied as part of FIC 101's
functionality. The output of FIC 101 is an electrical signal to TY 101 located in an inaccessible or
behind-the-panel-board location. The output signal from TY 101 is a pneumatic signal (line with
double forward slash marks) making TY 101 an I/P (current to pneumatic transducer). TT 101 and
TIC 101 are similar to FT 101 and FIC 101 but are measuring, indicating, and controlling
temperature. TIC 101's output is connected via an internal software or data link (line with bubbles)
to the setpoint (SP) of FIC 101 to form a cascade control strategy.

Often P&ID's include a cover page where common and typical terms, symbols, numbering systems,
etc., are defined. On the example, Typical YIC would likely appear on the cover page and the
simplified form of YIC would appear throughout the P&IDs.

Typical YIC indicates an on/off valve is controlled by a solenoid valve and is fitted with limit switches
to indicate open (ZSH) and closed (ZSL) positions. All inputs and outputs are wired to a PLC that's
accessible to the operator (diamond in a square with a solid horizontal line). The letter 'Y' indicates
an event, state, or presence. The letter 'I' depicts indication is provided, and the letter 'C' means
control takes place in this device.

Adherence to ISA's S5.1 Instrumentation Symbols and Identification standard ensures a consistent,

http://www.controleng.com/article/ca152141.html 05/11/2008
How to read P&IDs - 8/1/2000 - Control Engineering Página 2 de 3

system independent means of communicating instrumentation, control, and automation intent is

developed for everyone to understand.

General instrument or function symbols

Auxiliary
Primary location
location
accessible to Field mounted
accessible to
operator
operator

Discrete
instruments

Shared display,
shared control

Computer
function

Programmible
logic control

1. Symbol size may vary according to the user's needs and the type of document.
2. Abbreviations of the user's choice may be used when necessary to specify location.
3. Inaccessible (behind the panel) devices may be depicted using the same symbol but
with a dashed horizontal bar.

Source: Control Engineering with data from ISA S5.1 standard

Identification letters
First letter Succeeding letters
Measured or Readout or Output
Modifier Modifier
initiating variable passive function function
A Analysis Alarm
B Burner, combustion User's choice User's choice User's choice
C User's choice Control
D User's choice Differential
Sensor (primary
E Voltage
element)
Ration
F Flow rate
(fraction)
Glass, viewing
G User's choice
device
H Hand High
I Current (electrical) Indication
J Power Scan
Time, time Time rate of
K Control station
schedule change
L Level Light Low
Middle,
M User's choice Momentary
intermediate
N User's choice User's choice User's choice User's choice
O User's choice Orifice, restriction
Point (test
P Pressure, vacuum
connection)
Integrate,
Q Quantity
totalizer
R Radiation Record
S Speed, frequency Safety Switch
T Temperature Transmit
U Multivariable Multifunction Multifunction Multifunction
Vibration,
Valve, damper,
V mechanical
louver
analysis
W Weight, force Well
X Unclassified X axis Unclassified Unclassified Unclassified
Event, state, or Relay, compute,
Y Y axis
presence convert
Z Position, dimension Z axis Driver, actuator
Source: Control Engineering with data from ISA S5.1 standard

Common connecting lines

http://www.controleng.com/article/ca152141.html 05/11/2008
How to read P&IDs - 8/1/2000 - Control Engineering Página 3 de 3

Connection to process, or instrument

supply:

Pneumatic signal:

Electric signal:
Capillary tubing (filled system):

Hydraulic signal:

Electromagnetic or sonic signal (guided):

Internal system link (software or data

link):
Source: Control Engineering with data from ISA S5.1 standard

For more information on ISA standards, visit

www.isa.org or call 919/549-8411.

Dave Harrold, senior editor

Comments? E-mail [email protected]

TALKBACK

» SUBMIT FEEDBACK
.
Jude Boydston - 08/31/07
.
Oswaldo Pharo - 08/29/07
.
Andreas Helfrich - 08/20/07

» MORE

RELATED CONTENT
TOPICS AUTHOR

SPONSORED LINKS

Protect the availability, integrity, and confidentiality of your

network system
Learn how to protect your industrial network system today from
tomorrow's imminent threats. Download this webcast now!

Ads By Google

Watch Free PLC Tutorial

Lots of Smart I/O in Small Package. Fast, Programmable Logic Control.
www.GaliLmc.com

Digital Signal Processors

Expertise in Analog, Mixed-Signal & DSP Technologies. Learn More!
www.cirrus.com

Process Instruments
2-Wire & 3-Wire transmitters Industrial instrumentation
www.telmarinc.com

About Us | Advertising Info | Site Map | Contact Us | Useful Sites | FREE Subscription | RSS

© 2008 Reed Business Information, a division of Reed Elsevier Inc. All rights reserved.
Use of this Web site is subject to its Terms of Use | Privacy Policy

Please visit these other Reed Business sites

Media & Publishing: Business & Printing: Electronics:

Broadcasting & Cable | ContentAgenda | LA 411 | Converting | DM2-DecisionMaker | Expert Business EDN | Instat | Semiconductor International | Test &
Library Journal | Multichannel News | New York 411 | Source | Graphic Arts Blue Book | Graphic Arts Monthly | Measurement World | TWICE
Publishers Weekly | School Library Journal | Cr ticas | Hot Frog | Packaging Digest | The Industry Measure |
Tradeshow Week | Variety | Video Business Tracom Group | Zibb
Building & Construction:
Associated Construction Publications | Buildcore |
Manufacturing: Gifts & Furnishings: Building Design & Construction | Building Team
Control Engineering | Design News | Industrial Casual Living | Furniture Today | Gifts & Decorative Forecast | Construction Equipment | Consulting
Distribution | Logistics Management | Kellysearch | Accessories | Home Textiles Today | Home Accents Specifying Engineer | Custom Builder | Daily Commercial
Manufacturing Business Technology | Modern Materials Today | Jewelers Circular Keystone | Kids Today | News | Housing Giants | HousingZone | Interior Design |
Handling | Plant Engineering | Purchasing | Purchasing Playthings Journal of Commerce | Professional Builder |
Data | Supply Chain Management Review Professional Remodeler | Reed Connect | Reed
Construction Bulletin | Reed Construction Data |
Hospitality: SmartBuilding Index | RS Means
Subscriptions: Chain Leader | Foodservice Equipment & Supplies |
All Magazine and eNewsletter Subscriptions HOTELS | R&I

http://www.controleng.com/article/ca152141.html 05/11/2008