Scribd Logo
Upload

Welcome to Scribd!

  • 3 views

    3.5 inch One Trip Cement_Running Procedure

    Uploaded by

    Musa Abdulwahab

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    3.5 inch One Trip Cement_Running Procedure

    Uploaded by

    Musa Abdulwahab
    3 views5 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    3 views5 pages

    3.5 inch One Trip Cement_Running Procedure

    Uploaded by

    Musa Abdulwahab

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 5

    Bell WellScience Limited

    Thru-Tubing One-Trip
    Retainer
    Recommended Procedure
    BELL WELLSCIENCE LTD
    Generic

    Prepared for: ENERGY QUEST

    Prepared By: Musa Mike A


    June 21, 2024
    08032697939
    WELL INFORMATION

    WELL INFO: Generic

    TUBING: 31/2”

    CASING: N/A

    LINER: N/A

    MINIMUM ID: N/A

    PERFORATIONS: N/A

    GROSS PERFS: N/A

    NET PERFS: N/A

    FORMATION: N/A

    WELL FLUID: N/A

    BHP: N/A

    BHT: N/A

    MAX. DEV N/A


    Thru-Tubing One-Trip Retainer
    1. Conduct pre-job safety meeting as per ENERGY QUEST QUEST OIL FIELD
    SERVICES PROCEDURES

    2. R/U E-line and RIH w/ 3.660” gauge to desired depth. POOH. Note any tight spots
    encountered during gauge run.

    3. Pickle the CT reel to ensure there is no trash or debris present in the coil tubing. Catch
    the pickle and dispose as per Energy Quest Oil Field Services procedure.

    4. R/U Coil Tubing and wash out well to desired depth. Pick up to proposed set depth and
    Mark the CT for the retainer. POOH.

    5. RIH the following BHA on Coiled Tubing:


    LENGTH DEPTH
    OD ID (Feet) (Feet)
    Bottom of assembly
    i 2-1/8” NU 10 Rd Bull Plug 2.125 0.332
    3 1/2” 10.5#-15.1# Retainer Valve w/ 1-1/2”
    h 2.630 0.820 1.819
    NU 10 Rd Pin
    3-1/2” 9.3#-10.2# TTS Retrievable Paragon
    g 2.725 1.615 3.795
    II Packer
    To be left in well
    f Cement Squeeze Tool with 2-1/8” CS Box
    2.130" O.D. x 1.060" I.D. Pressure Relief
    e Assembly 1-1/4" CS Box x Pin (Pinned up 2.130 1.060 1.210
    to 6,000 psi)
    d Tubing Swivel w1-14”CS Pin x Box 2.130 1.100 1.522
    c 1-1/4” CS Box x 2-3/8” CS Pin Crossover 2.710 1.220 0.350
    b Motor Head Assemblies 2.125 0.690 2.450
    a Coiled Tubing Connector 2.125 1.050 1.361
    Total BHA

    6. Go in hole with cement retainer at a moderate rate. Stop at set depth. Record pick-up,
    slack off and neutral weight.

    7. Drop 5/8” steel ball and allow to gravitate to packer at set depth. Wait 1 hour.

    8. Pressure up to set packer. Slack off 4,000# on packer. Pressure up to 5,000 psi to
    fully set and release from cement retainer in 500 psi increments.Expect to see a sharp
    drop in pressure on the pressure gauge as the ball seat blows to open up circulation
    holes on the Cement retainer valve.
    9. Pressure up on Coiled Tubing/Production Tubing annulus 500 psi to test packer sealing
    integrity. Maintain 4,000 lbs. stacked weight and 500 psi pressure during pumping.

    10. Establish injection rates. Note and record same.

    11. Mix and pump slurry as per Energy Quest Oil Field Services procedure.

    12. Displace volume until squeeze pressure is reached.

    13. Once the squeeze is reached, shut down pump. Pick up and close Retainer Valve.

    14. POOH 200’ and circulate out excess volume remaining in Coiled Tubing and record
    volume recovered.

    15. Pull out of hole with Squeeze tool and, lay out same.

    16. WOC

    17. Continue as per Energy Quest Oil Field Services Procedure.


    Notes: The retainer(s) may encounter debris during run. If any debris obstructs the
    retainer from the set depth, wash the retainer down to set depth. Circulate until the
    returns are clean. Resume procedure at step 6.
    The retainer(s) may become stuck or plugged up due to the debris in the well. Pressure
    up to 6,000 psi to shear open the PRA and drop 5/8" ball and pressure up to 3,200 psi
    to shear hydraulic disconnect. POOH with running assembly. Start fishing operations.
    TITLE:
    3-1/2"ONE TRIP CEMENT RETAINER/PROPOSED

    SERVICE DISTRICT: SERVICE SPECIALIST:


    New Iberia
    a SIZE WEIGHT GRADE THREAD
    OPERATOR: CELL#: CASING

    COMPANY REP: PHONE #: LINER


    b
    BLOCK: WELL #: TUBING

    STATE: LEASE: WKSTRNG


    C
    ACCT. REP: PHONE #: PERFORATIONS:

    RIG NAME: COMP. FLUID: INHIBITOR: COATING:

    DATE SUBMITTED: QUOTE#: SCREEN SIZE: SAND SIZE: JOB #:

    PREPARED BY:MUSA MIKE PHONE #:08032697939 BHP (psi): BHT (°F): MAX. DEV.: ZONE DEV.:
    d
    No. DEPTH-FT. LENGTH-FT. O.D. I.D. DESCRIPTION
    a 1.360 2.125 1.020 2-1/8" Coil Tubing Connector 1-1/2"AMMT Pin

    b 2.450 2.125 0.690 2-1/8 Motor Head Assembly

    c 0.350 2.710 1.220 1-1/4"Ammt Box x Cs pini)

    d 1.521 2.130 1.100 Sealed Tubing Swivel)

    e 1.212 2.130 1.060 2.125 od x id pressure relief assembly


    e
    f Hydraulic Squeeze Setting Tool

    g 3.750 2.725 1.615 3-1/2" 15.1# Paragon II Packer 2.725"odx1.615"id

    h 1.81 9 2.630 0.820 3-1/2" Cement Retainer Valve 1-1/2" Nu Pin rd 10

    i 0.332 2.125 2-1/8” Nu Bull Plug

    End of Assembly
    f
    Total Length

    NOTES:

    You might also like