A B C D E F G H I

GENERAL NOTES-STRUCTURAL STEEL (UNLESS NOTED OTHERWISE ON INDIVIDUAL DRAWING) 4.0 BOLTS, NUTS AND WASHERS ABBREVIATIONS REFERENCE DRAWING
1.0 GENERAL 4.1 CONNECTION BOLTS:- (V) WORKING POINTS `WP' FOR BRACINGS SHALL BE ON CENTERLINES OF BEAMS/COLUMNS, UNLESS AB ANCHOR BOLT TITLE DRAWING NO.
(i) ORDINARY BLACK BOLTS (GRADE 4.6) SHALL BE OF 16mm DIAMETER (MAXIMUM) FOR HANDRAILS ONLY AND (UNDERSIDE OF FLOORING) NOTED OTHERWISE. @ AT THE RATE
1.1 THIS DOCUMENT COVERS THE GENERAL NOTES & ABBREVIATIONS USED IN STRUCTURAL DRAWINGS FOR CIVIL DESIGN BASIS 214455C-000-JSD-1700-0001
NEW 1500 MTPD SULPHURIC ACID PLANT - D. THIS DOCUMENT SHALL BE READ IN
SHALL CONFORM TO IS:1367. (VI) WP FOR BRACINGS AT BASEPLATE JUNCTION SHALL BE AT THE TOP OF BASEPLATE. BM BEAM
(ii) FOR SHEAR & MOMENT CONNECTIONS, HIGH STRENGTH BOLTS OF GRADE 8.8 CONFORMING HOWEVER, ANY OFFSET OF WP SHALL BE SUITABLY CONSIDERED IN THE DESIGN BACK TO BACK
CONJUNCTION WITH ALL DRAWINGS ISSUED FOR CONSTRUCTION. IN CASE OF CONFLICT B/B JOB SPECIFICATION FOR DESIGN -
TO IS:3757 & IS:1367 SHALL BE USED UNO. (vi) PLATFORM ELEVATION IS DEFINED BY TOP OF STEEL(TOS) ELEVATION WHICH IS TO THE TOP OF BEAM 214455C-000-JSD-2310-0001
7 BETWEEN THIS DOCUMENT & THE IFC DRAWINGS,THE LATER SHALL GOVERN.
(iii) HIGH STRENGTH BOLTS (GRADE 8.8) SHALL BE 20mm DIAMETER (MINIMUM) AND BCD BOLT CIRCLE DIAMETER EXTERNAL PAINTING 7
1.2 DRAWINGS SHALL NOT BE SCALED, ONLY WRITTEN DIMENSIONS SHOWN ON THE DRAWINGS SHALL BE FOLLOWED. UNLESS OTHERWISE NOTED ON THE DESIGN DRAWING. BKT BRACKET
16mm DIAMETER (MINIMUM) FOR ANGLES JOB SUPPLY SPECIFICATION
1.3 ALL DIMENSIONS ARE IN MILLIMETERS, COORDINATES AND ELEVATIONS ARE IN METRES. (vii) ALL WORK, INSPECTION & MATERIAL SHALL CONFORM TO RELEVANT APPROVED QUALITY CONTROL 214455C-000-JSS-1800-0001
(iv) ALL MAIN BOLTED CONNECTIONS SHALL BE PROVIDED WITH MINIMUM OF 2 NUMBERS OF 20mm DIAMETER BOLTS. BOS BOTTOM OF STEEL STEEL WORK
1.4 PLANT FGL IS SET AS EL100.000 WHICH CORRESPONDS TO EL. 5.00M ABOVE MSL. PLANS (QCP) AND STANDARD SPECIFICATION & CODES.
1.5 ALL ELEVATIONS INDICATED ON DRAWINGS REFER TO TOP OF STEEL.
(v) ALL HIGH STRENGTH NUTS AND WASHER SHALL CONFORM TO IS:6623 & IS:6649. B/S BOTH SIDES
(vi) ALL BOLTS SHALL BE SNUG TIGHT UNO. IN CASE FRICTION GRIP BOLTS OF SEISMIC RESISTING FRAMES (viii) SPLICES IN ROOF PURLINS SHALL BE STAGGERED.
ELEVATION INDICATED FOR BASE PLATE REFER TO BOTTOM OF STEEL (BOBP) BOBP BOTTOM OF BASE PLATE
(GRADE 8.8 OR 10.9) ARE USED, PRETENSION SHALL BE ESTABLISHED AS SPECIFIED IN IS:4000. STEEL LAYOUT (ix) SPLICING OF BEAM FLANGE PLATES, BEAM WEB PLATES, SHALL BE DONE BY FULL PENETRATION BUTT
1.6 ALL STEEL WORKS BOLTING , WELDING , PAINTING SHALL BE IN ACCORDANCE WITH SPECIFICATION
AND SHOP ERECTION DRAWING SHOULD CLEARLY SHOW THE BOLTS WHICH NEED TO BE PRETENSIONED. BP BASE PLATE
WELD. MOMENT SPLICE SHALL PREFERABLY BE LOCATED NEAR 1/3 OF BEAM SPAN & SHEAR SPLICE
NOS. 214455C-000-JSS-1800-0001 C CENTER LINE
(vii) ALL BOLTS OF GRADE 4.6 & 8.8 WITH CORRESPONDING NUTS & WASHERS SHALL BE HOT-DIP LOCATED CLOSE TO CENTRE OF SPAN.
1.7 ALL WELDING SHALL CONFORM TO IS:816, IS:819, IS:1024, IS:1261, IS:1323, IS:9595 AS APPROPRIATE. CARBON STEEL
GALVANIZED IN ACCORDANCE WITH IS:1367 (PART 13) NUT SHALL BE HEXAGONAL HEADED. (x) COLUMN SPLICE SHALL BE LOCATED WITHIN MIDDLE ONE THIRD OF COLUMN CLEAR HEIGHT UNO. CS
1.8 ALL FABRICATION SHALL BE AS PER IS:800-2007 & IS:816.
1.9 THE HANDRAIL APPROACH TO AND FROM EXIT AREAS SHALL BE SMOOTH AND CONTINUOUS KNEE
(viii)ALL ERECTION BOLT SHALL BE BLACK BOLTS CONFORMING TO IS:1367 CLASS 4.6 SHALL BE OF 16mm CLR
L CLEAR
DIAMETER (MAXIMUM) & MINIMUM 2 NOS. OF 16 mm DIAMETER TO BE USED FOR ERECTION PURPOSE. COLUMN
RAILS AND KICK PLATE SHALL ALSO BE CONTINUOUS WITH THOSE OF ADJACENT WALKWAYS, PLATFORMS 6.3 FABRICATION COL
4.2 BOLT HOLES SHALL BE DRILLED AND EDGES SHALL BE REAMED. NO BOLT HOLE SHALL BE GAS CUT.
AND STAIRS
4.3 HOLE DIAMETER FOR STRUCTURAL BOLTS : (TABLE 19 OF IS:800) (i) ALL BRACING WORK POINTS MUST BE IN ACCORDANCE WITH DESIGN DRAWINGS. VARIATIONS c/c CENTER TO CENTER
1.10 DISCREPANCY IN DRAWING, IF ANY, SHALL BE BROUGHT TO THE NOTICE OF THE SITE ENGINEER, WILL NOT BE PERMITTED WITHOUT PRIOR AGREEMENT. CONN CONNECTION THK THICK
NOT EXCEEDING 24 mm DIAMETER : 2 mm GREATER THAN THE BOLT DIAMETER
PRIOR TO CONSTRUCTION. DETAIL
6 GREATER THAN 24 mm DIAMETER : 3 mm GREATER THAN THE BOLT DIAMETER (ii) CUTOUTS IN FLOORING UP TO 300mm x 300mm OR 300 mm DIAMETER SHALL BE MADE AT SITE WHILE DET TOP TOP OF PLATE 6
1.11 ALL DIMENSIONS AND LEVELS SHALL BE PHYSICALLY VERIFIED AT SITE, ANY DISCREPANCY SHALL BE
REPORTED TO ENGINEER-IN-CHARGE/DESIGN OFFICE PRIOR TO EXECUTION.
BOLTED SPLICE CONNECTION : 1 mm GREATER THAN THE BOLT DIAMETER. BIGGER CUTOUTS SHALL BE MADE IN SHOP AND PROVIDED WITH TOE PLATE. DWG DRAWING TOR TOP OF ROD
FOR STEEL-TO-STEEL CONNECTIONS, UNLESS NOTED OTHERWISE. SIZE OF THE BOLT HOLE FOR OVER SIZE & (iii) STAIRS, LADDERS & HAND RAILS SHALL BE AS PER STANDARD DRAWINGS. DIAMETER TOS TOP OF STEEL
1.12 ALL MATERIAL SHALL BE PROCURED FROM APPROVED SUPPLIER/VENDORS. 'D' OR 'DIA' OR 'Ø'
SLOTTED HOLES SHALL BE AS PER TABLE 19 IS:800-2007. (iv) DIMENSIONS OF DIAGONAL MEMBERS & GUSSETS SHALL BE CONFIRMED BY SHOP LAYOUT BEFORE
1.13 MINIMUM CONNECTION PLATE THICK 10MM UNLESS SPECIFIED OTHERWISE.
4.4 ALL END PLATES, STIFFENERS AND CLEATS FOR THE BOLTED AND WELDED CONNECTIONS SHALL BE EJ EXPANSION JOINT TYP TYPICAL
TAKING UP FABRICATION. EL ELEVATION TOG TOP OF GRATING
MINIMUM 8 mm THICK UNLESS NOTED OTHERWISE. MINIMUM GUSSET PLATE THICKNESS FOR TRUSSES
(v) COLUMN CAP PLATE SHALL BE MILLED TO ENSURE PROPER CONTACT BEARING SURFACE BETWEEN EQUAL
2.0 MATERIALS & GIRDERS IS 8 MM FOR SPAN UPTO & INCLUDING 12 M ABOVE WHICH THICKNESS IS 10 mm. EQ T&B TOP & BOTTOM
PLATES.
2.1 ALL STRUCTURAL STEEL SHAPES, BARS, PLATES SHALL BE OF GRADE E250 BR CONFORMING TO IS 2062 & S275 JR
4.5 ALL HOLLOW SECTIONS AND TUBES SHALL BE FULLY SEALED AT THE END WITH 6 mm PLATES WELDED EQPT EQUIPMENT TM TEMPORARY MEMBER
ALL ROUND, UNLESS NOTED OTHERWISE ON THE DESIGN DRAWINGS. (vi) (i)THE WIDTH OF GAP BETWEEN THE ENDS OF MEMBERS CONNECTED BY BOLTS SHALL BE MAXIMUM
CONFORMING TO EN 10025 HAVING MINIMUM YIELD STRENGTH OF 250 MPA & 275 MPA RESPECTIVELY. EF EACH FACE U/S UNDER SIDE
4.6 ALL STEEL WORK WHICH IS TO BE ENCASED SHALL BE PAINTED AS PER 214455C-000-JSS-1800-0001 1.5 mm FOR DEPTH OF SECTIONS UPTO 1000 mm.
2.2 STEEL OF GRADE E250BR CONFORMING TO IS2062 SHALL BE USED FOR STAIRS, LADDERS,MISC.PLATFORMS,ETC.
4.7 a) HINDALCO EVERLAST MILL FINISH HI CREST 0.71 MM PROFILE SHEET OF NOMINAL
FS FAR SIDE UNO UNLESS NOTED OTHERWISE
(ii) THE PERMISSIBLE TOLERANCE ON THE LENGTH OF INDIVIDUAL COMPONENTS SHALL BE ± 3 mm
AS PER CONSTRUCTION DRAWINGS (FP) FIRE PROOFING WITH TOP VERT VERTICAL
1144 MM OVERALL WIDTH AND NOMINAL 46 MM DEEP RIBS WITH SUBTLE SQUARE FOR UPTO & INCLUDING 12 M LENGTH & ± 0.00025 L SUBJECT TO MAXIMUM OF ± 5 mm FOR OVER
2.3 TUBULAR STEEL SHALL CONFORM TO Yst 310 OF IS 1161.
FLUTING IN THE SIX PAN TO NOMINAL 175 MM CENTRE TO CENTRE. 12 M LENGTH MEMBER, HERE 'L' IS THE LENGTH OF MEMBER. FLG EXPOSED WP WORKING POINT
2.4 SQUARE,RECTANGULAR,HOLLOW SECTIONS CONFIRM TO Yst 310 OF IS 4923
2.5 PIPE OR POSTS AND HANDRAILS SHALL BE SS304 SCHEDULE 20 MIN.
b) HINDALCO EVERLAST COLOR COATED HI CREST 0.71MM PROFILE SHEET FOR WALL CLADDING OF
(iii) THE PERMISSIBLE DEVIATION OF THE AXES OF THE MEMBERS MEETING AT A JOINT FROM THEORETICAL FP FULLY ENCASED FIRE PROOFING
5 2.6 CRANE RAILS SHALL BE IS:3443
NOMINAL 1144 MM OVERALL WIDTH AND NOMINAL 46 MM DEEP RIBS WITH 175 MM CENTRE TO CENTRE.
NODAL POINTS SHALL NOT BE GREATER THAN ±3 mm. FGL FINISHED GRADE LEVEL TYPICAL BUILD UP SECTION DESIGNATION 5
COLOR - EMERALD GREEN
(iv) THE ERECTION CLEARANCE FOR STRUCTURAL MEMBERS AT EACH END SHALL NOT BE FLG FLANGE BU "A"X "B" X "C" X "D"
3.0 WELDING 4.8 ALL HIGH STRENGTH BOLTS SHALL BE MADE AS PER IS3757
EXAMPLE BU 1000 X 500 X 40 X 20
WITH PROPERTY CLASS IS1367(PART 3), "ONE NUTS" AS PER IS6649 AND WASHERS AS PER IS 6649 GREATER THAN THE FOLLOWING : FFL FINISHED FLOOR LEVEL
3.1 ELECTRODES USED FOR WELDING SHALL COMPLY WITH IS:814 OR IS:815 AND ASME SECTION II (PART C).
HIGH STRENGTH BOLTS, NUTS AND WASHERS SHALL COMPLY THE a) 2 mm FOR MEMBERS WITH END CLEATS OR PLATES. F/F FACE TO FACE "B" = 500MM
3.2 ALL CONNECTIONS EXCEPT SHOWN OTHERWISE ARE WELDED AND ALL WELDS ARE 6mm FILLET WELD
CONTINUOUS. REQUIREMENTS OF IS1367 & IS3757.THE DESIGN TORQUE WILL BE INDICATED ON THE STANDARD b) 3 mm FOR BEAMS WITHOUT WET CLEATS AND END PLATES. FB FACE BAR
3.3 ALL WELDING SHALL BE DONE AS PER SPECIFICATIONS USING ELECTRODES OF APPROVED STEEL STRUCTURE CONNECTIONS. GRTG GRATING BUTT WELD
- "IN CASE OF VIBRATING OR DYNAMIC LOADS, LOCKNUTS SHALL BE PROVIDED"
MANUFACTURER & CONFORMING TO IS:814 & IS7280 . ALL OTHER CONSUMABLE SHALL BE AS PER SPECIFICATIONS.
- "HIGH STRENGTH BOLTS (GRADE 10.9) SHALL BE USED FOR FRICTION GRIP TYPE BEAM MOMENT CONNECTIONS" 6.4 PAINTING GALV GALVANIZED AS PER IS:816-CI-6.1
3.4 UNLESS SHOWN OTHERWISE ON DRAWINGS, ALL SHOP WELDS SHALL BE MINIMUM 6 mm THICK HR HANDRAIL (TYP)
- "HIGH STRENGTH BOLTS (GRADE 8.8) SHALL BE USED FOR TURNED AND FITTED TYPE BEAM MOMENT (I) ALL STEEL WORKS SHALL BE PAINTED AS PER 214455C-000-JSD-2310-0001
CONTINUOUS FILLET WELDS AND ALL FIELD WELDS SHALL BE MINIMUM 8 mm THICK CONTINUOUS FILLET WELD.
H.S.BOLT HIGH STRENGTH BOLT

"A" = 1000MM
3.5 ALL CONNECTIONS EXCEPT SHOWN OTHERWISE ARE WELDED AND ALL SHOP WELDED CONNECTIONS CONNECTIONS" (II) ALL LIFTING BEAMS/MONORAILS/CRANE GIRDERS SHALL BE PAINTED. CLEARLY INDICATING ITS HOIST "D" = 20MM
SHALL BE FULL STRENGTH WELD UNLESS NOTED OTHERWISE. LIFTING CAPACITY. HOR HORIZONTAL
Pocket NUT IS 6623
HPP HIGHEST PAVING POINT

"C" = 40MM
3.6 ALL BUTT WELDS SHALL BE FULL STRENGTH BUTT WELDS WITH REQUISITE EDGE PREPARATION FOR (III) STRUCTURAL PARTS INACCESSIBLE AFTER ASSEMBLING SHALL BE PAINTED BEFORE ASSEMBLY / ERECTION.
(grade 8.8)
MEMBERS WITH THICKNESS MORE THAN 8 mm. ID INSIDE DIAMETER
3.7 SEAL WELD SHALL BE MINIMUM 3 mm FILLET WELD. IP INSERT PLATE
4 3.8 ALL BATTENS/LACINGS/BOX SECTIONS SHALL HAVE CONTINUOUS WELDING UNLESS SHOWN OTHERWISE Bolt 6.5 ERECTION 4
IL INVERT LEVEL
ON IFC DRAWINGS. STITCH WELDING WILL NOT BE PERMITTED WITHOUT PRIOR APPROVAL OF ENGINEER-IN-CHARGE. (i) STEEL WORKS SHALL BE ERECTED WITHIN TOLERANCES SPECIFIED IN IS 12843.
3.9 THE PAINT SHALL BE REMOVED FOR A DISTANCE OF 50 mm ON EITHER SIDE OF THE JOINT BEFORE ANY WELDING Plain washer IS 6649 JT JOINT
(ii) COLUMN BASES SHALL BE GROUTED AS EARLY AS POSSIBLE AFTER ERECTION
IS CARRIED OUT. THE WELDED AREA SHALL BE THOROUGHLY CLEANED BEFORE TOUCH UP. kg KILOGRAM
4.9 BOLTS M16,M20 ACCORDING IS1367 & IS3757 STRENGTH CLASS 8.8 ARE COMPLETED WITH PREFERABLY BEFORE BOLTING.
3.10 WHEN HEATING THE JOINT TO BE WELDED, AWS D1.1 CODE REQUIREMENTS SHALL BE FOLLOWED kN KILO NEWTON
3.11 FILLER RODS AND WIRES FOR GAS WELDING SHALL CONFIRM TO IS 1278. ONE NUT ACCORDING IS6623 STRENGTH (iii) HOLDING DOWN BOLTS AT THE COLUMN BASES SHALL BE CHECKED FOR WRENCH CLEARANCES
kNm KILO NEWTON METRE
3.12 THE PERMISSIBLE STRESSES FOR SHEAR AND TENSION FOR SITE WELDS SHALL BE REDUCED TO 80% OF CLASS 8 ACCORDINGLY AND ONE SPRING WASHER ACCORDING AND THOROUGHLY TIGHTENED TO DEVELOP FULL FIXITY OF BASE.
IS6735 AND ONE PLAIN WASHER ACCORDING AS PER IS5370 Pocket LG LONG
SHOP WELD. NUT (iv) ALL GALVANIZED SURFACES DAMAGED DURING ERECTION SHALL BE REPAIRED
3.13 BUTT WELDS: AS PER IS:816-CI-6.1 Bolt LLH LONG LEG HORIZONTAL
AS PER 214455C-000-JSS-1800-0001.
LLV LONG LEG VERTICAL
(v) ALL PAINTED SURFACES DAMAGED DURING ERECTION SHALL BE REPAIRED
L STRUCTURAL ANGLE
AS PER 214455C-000-JSS-1800-0001.
TYPICAL DETAILS OF BUTT WELDS (EDGE PREPARATION AS PER IS:9595) m2 SQUARE METER
(vi) PROPER SEATING CLEATS AND/OR ERECTION BOLTS SHALL BE PROVIDED WHEREVER FIELD WELDING
3
Spring washer IS6735 MC MOMENT CONNECTION
3

Plain washer IS5370 Digitally signed

IS ENVISAGED.
(vii) ADEQUATE TEMPORARY BRACINGS/SUPPORTS, AS APPROVED BY THE ENGINEER-IN-CHARGE, SHALL BE
MT METRIC TONNE Goutam bySwain
Goutam
MAX

mm MILLIMETER
3-6

3
APPLICATION OF SPRING LOCK WASHERS IS NOT ALLOWED FOR OVAL HOLES Pocket NUT PROVIDED BY THE CONTRACTOR TO ENSURE SAFETY DURING ERECTION. Swain 23:27:16
Date: 2024.03.02 3
3

Bolt MS MILD STEEL +05'30'

T>12

3 AND WHEN DIFFERENCE BETWEEN DIAMETER OF THE HOLE AND THE BOLT IS (viii) NO PART OF THE STRUCTURE SHALL BE USED FOR ERECTION PURPOSES WITHOUT PRIOR APPROVAL OF
== MK MARK
Balachandar Dhanabal
VETRIMANI G
2024.02.23 10:45:54 +05'30' 2024.02.23 13:50:59 Senguttuvan Swaminathan

MORE THAN 3MM; AS WELL AS FOR JOINT PLACEMENT WITH ROUND WASHER
+05'30' 2024.02.23 14:04:12 +05'30'

ENGIREER-IN-CHARGE.
IT SHALL NOT BE USED FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT IS SUPPLIED. CONFIDENTIAL – NOT TO DISCLOSE WITHOUT PRIOR AUTHORIZATION

B 23-FEB-24 ISSUED FOR DESIGN GVM DBR SEN

DETAIL-1 ACCORDING IS6649 .FOR THE SAID CASES AS WELL AS WHEN ML MATCH LINE
2

SQUARE BUTT WELD 45° DETAIL-2 (ix) MINOR HANDRAIL ADJUSTMENTS TO TOP RAIL, MID RAIL OR TOE PLATE AT LOCATIONS WHERE PIPING & A 19-JAN-24 ISSUED FOR REVIEW GVM DBR SEN
TYP THE BOLT WORKS IN TENSION IS USED THE SET OF 2 WASHERS ACCORDING m METRES Rev Date Description of Issue Written by Checked by Approved by
45°
DOUBLE BEVEL BUTT WELD SUPPORTS ARE REQUIRED SHALL BE MADE IN THE FIELD IF NECESSARY. HANDRAIL POST SHALL BE DD-MMM-YY

TYP
IS5370 WITH 2 NUTS ACCORDING IS6623. Plain washer M-20 METRIC BOLT & DIAMETER DOCUMENT CATEGORY DOCUMENT REVIEW STATUS (BY CLIENT)
ADJUSTED OR ADDED FOR SUPPORTS AT DISCONTINUOUS RAIL THAT HAVE BEEN FIELD CUT.
IS5370 N NEWTON (USE " X " MARK)
45°
5.0 FLOORING NB NOMINAL BORE APPROVAL

NS
3

NEAR SIDE REVIEW

3

5.1 GRATING (ELECTRO FORGED TYPE) PANELS,STAIR TREADS SHALL BE HOT DIPPED SYMBOLS MARKED AS:- WELDING SYMBOLS
T>5

NTS
THIS DOCUMENT IS DEVELOPED BY TECHNIP ENERGIES INDIA LIMITED AND THE INFORMATION IT CONTAINS IS PROPRIETARY.

NOT TO SCALE
INFORMATION
GALVANIZED (UNO). THE MINIMUM THICKNESS OF GALVANIZING SHALL BE 90-100 MICRON.
T>10

5.2 GRATINGS SHALL BE 32 & 40mm THICK. NF NEAR FACE PROJECT

MOMENT CONNECTION (MC) INDICATION OF FIELD/SITE
BACKING STRIP 5.3 GRATING SHALL HAVE A MINIMUM BEARING OF 30 mm AT EACH SUPPORTS. FILLET WELD NGL NATURAL GROUND LEVEL NEW 1500 TPD SULPHURIC ACID PLANT – D
R

3
R=0

5.4 A 12mm DIA DRAINAGE HOLE SHALL BE PROVIDED (UNLESS NOTED OTHERWISE )FOR EVERY 1.0M² OF FLOOR
3

10x6 FLAT SPANING DIRECTION OD OUTER DIAMETER PARADEEP, ODISHA, INDIA

PLATE WITH A MINIMUM OF ONE HOLE PER PANEL, SHOWN OTHERWISE ON DESIGN DRAWING.
2MM

INDICATION OF SHOP
GAP

2 6 2
R = 1MM FOR T < 12MM * BACKING STRIP 5.5 FOR PIPING AND OTHER PENETRATIONS THROUGH FLOORING, OPENINGS SMALLER THAN THAT LISTED IN THE GRATING FLOOR FILLET WELD ON ARROW SIDE PLT PLATE
DETAIL-3 4 DETAIL-4
R = 2MM FOR T > 12MM 10x6 FLAT FOLLOWING SHALL BE LOCATED AND CUT BY THE FIELD. ALL AROUND OF SHOP FILLET PCD PITCH CIRCLE DIA OWNER
SINGLE BEVEL WELD SINGLE 'V' BUTT WELD FOR PLATE < 12 THK
WITH BACKING STRIP WITH BACKING STRIP
300 mm DIA. FOR GRATING FLOORING. FIELD SHALL PROVIDE ``GRATING PENETRATION COLLARS". WHEN FOR ANY OPENING IN FLOOR WELD OF (F.S) OTHER SIDE OF ARROW QTY QUANTITY PARADEEP PHOSPHATES
REASON THE CLEAR SPACE BETWEEN THE PIPE / INSULATION AND THE EDGE OF FLOORING EXCEEDS 50 mm ON R
FOR PLATE > 12 THK ANY SIDE, FIELD SHALL SUPPLY AND INSTALL A PENETRATION COVER PLATE IN ACCORDANCE WITH
RADIUS LIMITED
LEVEL MARK IN PLAN ARROW SIDE & OTHER SIDE
REV REVISION
60°

FLANGE/WEB PLATE SPECIFICATION. IT MAY BE NECESSARY TO REMOVE TOE PLATE WHERE PROVIDED. FILLET WELD PMC CONSULTANT
LEVEL MARK IN ELEVATION
RL REDUCED LEVEL SHIV SULPHURIC SOLUTIONS
6.0 DESIGN, FABRICATION AND ERECTION PERMANENT BOLTS ALL AROUND OF SHOP SQ SQUARE (OPC) PVT LTD.
3

ERECTION BOLTS FILLET WELD ON ARROW SIDE

6.1 ALL STRUCTURAL , DESIGN , SUPPLY , FABRICATION , BOLTING , WELDING , PAINTING , ERECTION STEEL WORKS SS SLIDING SUPPORT
T>12

SHALL BE IN ACCORDANCE WITH SPECIFICATION NOS . 214455C-000-JSD-1700-0001 & 214455C-000-JSS-1800-0001 HANDRAIL SCH SCHEDULE EPCM CONTRACTOR
ALL AROUND SITE FILLET
6.2 DESIGN ON ARROW SIDE STIFF STIFFENER TECHNIP ENERGIES INDIA LIMITED
2

3 CLOUD INDICATING REVISION

(I) SPLICES SHALL BE DESIGNED TO TRANSFER FULL STRENGTH (MINIMUM 100%) OF THE MEMBER SPLICED. DOUBLE - V - BUTT WELD SUPP SUPPORT
400
DETAIL-5 (II) ENDS OF THE COLUMNS SHALL BE FINISHED TO PERMIT FULL BEARING CONTACT AT SPLICE JOINTS CLOUD INDICATING HOLD STD STANDARD TITLE
*
1 DOUBLE V BUTT WELD ADDITIONAL SPLICE PLATE AND BASE PLATE CONNECTIONS STRUC STRUCTURE 1
X SECTION MARK ALL AROUND GRIND GENERAL NOTES FOR
MIN. 10 THK (III) STRUCTURAL CONNECTIONS SHALL BE CONCENTRIC EXCEPT AS FOLLOWS:- G FINISH BEVEL WELD SYM. SYMMETRICAL
* TOP FLANGE OF BEAMS WELDED THUS STRUCTURAL STEEL WORKS
SHALL BE GROUND FLUSH TYPICAL DETAILS OF (A) BOLTED ANGLE BRACING - USE BOLT GAUGE LINE OR CENTER LINE OF BOLT GROUP SWL SAFE WORKING LOAD
FILLET WELD STAGGERED INTERMITTENT
SHOP SPLICE (B) CHANNELS - USE BACK OF CHANNEL ON ARROW AND OTHER SIDE DRAWING NO. PAGE REV.
(IV) BEVEL WASHERS SHALL BE USED TO PROVIDE PROPER BOLTING CONNECTIONS FOR EQUIPMENTS &
SCALE 214455C 000 DW 1802 0001
MONORAIL SUPPORTS. NTS PROJECT UNIT DOC. TYPE MAT. CODE SER. NO.
1 OF 1 B

A B C D E F G H I
CAD FILE NAME : 214455C-000-DW-1802-0001.DWG SHEET SIZE : A1