IP5353

Support High Voltage SCP、Bi-directional PD3.0 and Fast

Charge protocol Power Bank SOC
 Support 4.20V、4.30V、4.35V、4.40V battery
1 Features  Boost
 Output current:
 Support multiple ports simultaneously
 [email protected] [email protected] [email protected]
AABC scheme
 Up to 95%@5V@2A efficiency with
 1 USB C input / output port
synchronous switching

p.
 2 USB A output ports
 Support line compensate
 1 USB B input port
AACL scheme  Battery level display
 1 USB C input / output port  Support 4 LED battery level indicator
 2 USB A output ports  Others

or
 1 Lightning input port  Support auto detect of plug in and out
 ABCL scheme  Fast charge status indicator
 1 USB C input / output port  Enter standby mode automatically in light
 1 USB A output ports load
 1 USB B input port  Support Battery NTC

C
 1 Lightning input port  Integrated torch-light driver
 Support I2C interface
 Fast charge
 Support 5V、9V、12V voltage input / output
 Multiple protection,high reliability
 Inuput overvoltage and undervoltage
 Support QC2.0 / QC3.0 output
protection
 Support FCP input / output

IC
Output overcurrent,overvoltage and short
 Support AFC input / output
circuit protection
 Support [email protected] high voltage SCP output
 Battery overcharge,over discharge and
 Support USB C DRP input / output
overcurrent protection
 Support BC1.2 / Apple / Samsung
 Over temperature protection
 Integrated USB PD2.0 / PD3.0 protocol  Input / Output battery temperature protection
IN

 Support PD2.0 input / output protocol  4kV ESD

 Support PD3.0 input / output and PPS output
 Low BOM cost
protocol
 Integrated switch power MOSFET
 PPS support 3.3V~11V adjustable voltage
 Single inductor for charging and discharging
with 20mV / Step
 Integrate BMC protocol  Package size: 6mm × 6mm 0.5pitch QFN40
JO

 Integrate Physical Layer protocol

 Integrate hardware CRC
2 Applications
 Support Hard Reset  Power Bank, Portable Charger
 Charger  Smart Phones, Tablets and Portable
 Support 18W charging power, Up to 5.0A devices
charging current at battery port
 Adaptive charging current adjustment
IN

V1.01 Email: [email protected] 1 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
3 Description
IP5353 is a power management SOC. It integrates QC2.0/ QC3.0/SCP output fast charging protocol,
FCP/ AFC input and output fast charging protocol, USB C/PD2.0/PD3.0 input and output protocol, USB C
PD3.0 PPS output protocol, and BC1.2/Apple/ Samsung mobile phone charging protocol. It integrates the
functions of synchronous up / down converter, lithium battery charging management, battery power
indication, etc. to provide a complete power solution for fast charging mobile power bank. Any single USB
port can support fast charging. When two or more output ports are used at the same time, only 5V is

p.
supported.
Only one inductor is needed to realize the function of buck and boost, and only a few peripheral
devices are needed in the application, which effectively reduces the size of the overall PCB and reduces
the cost of BOM.

or
The synchronous switch boost system of IP5353 can provide the maximum output capacity of
22.5W([email protected]). When boost has no load, it will automatically enter the sleep mode.
IP5353 charger provides 18W charging power and charging current up to 5.0A. Built in IC

C
temperature, battery temperature and input voltage control loop, intelligent regulation of charging current.
IP5353 supports 4LED battery level indicator. IP5353 supports lightning function and supports
buttons.
IP5353 supports I2C control interface.
IC
IN
JO
IN

V1.01 Email: [email protected] 2 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
Contents
1 Features .................................................................................................................................................... 1
2 Applications ............................................................................................................................................... 1
3 Description ................................................................................................................................................ 2
4 Reversion History ...................................................................................................................................... 4
5 Simplified Application ................................................................................................................................ 5
6 IP Series Products List .............................................................................................................................. 6

p.
6.1 Power Bank IC ................................................................................................................................ 6
6.2 IP5353 Common Customized Model Description........................................................................... 6
7 Pin Configuration and Functions ............................................................................................................... 8
7.1 IP5353 Pin Functions ...................................................................................................................... 8

or
8 Functional Block Diagram ....................................................................................................................... 10
9 Absolute Maximum Ratings..................................................................................................................... 10
10 Recommended Operating Conditions ....................................................................................................11

C
11 Electrical Characteristics ........................................................................................................................11
12 Function Description ............................................................................................................................. 14
12.1 Low power lock out and activation.............................................................................................. 14
12.2 Charge ........................................................................................................................................ 14
12.3 Boost ........................................................................................................................................... 14
IC
12.4 USB C ......................................................................................................................................... 17
12.5 USB C PD ................................................................................................................................... 19
12.6 Fast Charge Protocol .................................................................................................................. 19
12.7 Charge and Discharge Path Management ................................................................................. 20
IN

12.8 Automatic Detection of Mobile Phone......................................................................................... 22

12.9 KEY ............................................................................................................................................. 22
12.10 Fast Charge State Indication .................................................................................................... 22
12.11 Selection of Battery Charge Discharge Curve .......................................................................... 22
JO

12.12 Battery Level Display ................................................................................................................ 23

12.13 Abnormal prompt....................................................................................................................... 24
12.14 VSET（Battery voltage selection） .......................................................................................... 24
12.15 NTC function ............................................................................................................................. 25
12.16 I2C ............................................................................................................................................. 26
IN

12.17 Apple lightning line communication .......................................................................................... 26

13 PCB Layout ........................................................................................................................................... 27
13.1 Location of VOUT1 / VOUT2 / VBUS capacitor ......................................................................... 27
13.2 Location of VSYS capacitor ........................................................................................................ 27
13.3 Location of BAT/NTC capacitor .................................................................................................. 28
14 Typical Application Diagram .................................................................................................................. 29
14.1 IP5353_AABC ............................................................................................................................. 29
14.2 IP5353_AACL ............................................................................................................................. 31
14.3 IP5353_ABCL ............................................................................................................................. 33
15 Package................................................................................................................................................. 35

V1.01 Email: [email protected] 3 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
15.1 Package of the Chip.................................................................................................................... 35
15.2 Marking Description .................................................................................................................... 36
16 IMPORTANT NOTICE ........................................................................................................................... 37

4 Reversion History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
First Release V1.00 (July 2022) Page

p.
● First release.......................................................................................................................................1

Modified version V1.00 (Jul 2022) to V1.01 (Aug 2022) Page

or
● Changes and additions to partial descriptions...................................................................................1
● Add the description of low-voltage SCP for common IP5353 models...............................................6

C
IC
IN
JO
IN

V1.01 Email: [email protected] 4 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
5 Simplified Application

49
27
28
VBUS GND
VBUS
VBUS EPAD
DMC 19 15
DPC DPC KEY
20
TYPE-C CC1 DMC
21
CC2 CC2
22
GND CC1

p.
8
HLED
12
VOUT2 13 VOUT2
DMA2
VOUT2
23
USB-A DPA2 DPA2

or
24
GND DMA2

IP5353

C
29
VOUT1 30 VOUT1
VOUT1
DMA1 17
USB-A DPA1 DPA1
18
GND DMA1
2
LED3
IC
1
VIN 9 LED2
VIN
DMB 25
Micro-B DPB/DAT 32
DPB 26
LED1
GND DMB/CL
10
VING
11 16
VSYS
IN

31 NTC
VSYS VSYS

BAT BST LX LX LX LX
14

6
5

3
7

4
JO

BAT
IN

Figure 1 Simplified Application

V1.01 Email: [email protected] 5 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
6 IP Series Products List

6.1 Power Bank IC

boost / charge Main feature Package
IC QC PD3. Com
LED ligh US
Part No. boost charge key I2C DCP Certif 0 Package patib
number t BC
icate /PPS ility

p.
IP5303T 1.0A 1.2A 1,2 √ √ - - - - - ESOP8
IP5305T 1.0A 1.2A 1,2,3,4 √ √ - - - - - ESOP8 PIN2
IP5306 2.4A 2.1A 1,2,3,4 √ √ √ - - - - ESOP8 PIN

or
IP5306H 2.4A 2.1A 1,2,3,4 √ √ √ - - - - ESOP8
IP5406T 2.4A 2.1A 1,2,4 √ √ - - - - - ESOP8
IP5407 2.4A 2.1A 1,2,4 √ √ - - - - - ESOP8
IP5207 1.2A 1.2A 3,4,5 √ √ - √ - - - QFN24

C
PIN2
IP5209 2.4A 2.1A 3,4,5 √ √ √ √ - - - QFN24
PIN
IP5209U 2.4A 2.1A 3,4,5 √ √ √ √ - - - QFN24
IP5207T 1.2A 1.2A 1,2,3,4 √ √ √ √ - - - QFN24
PIN2
IP5189T 2.1A 2.1A 1,2,3,4 √ √ √ √ - - - QFN24
IC
PIN
IP5189TH 2.1A 2.1A 1,2,3,4 √ √ √ √ - - - QFN24
IP5310 3.1A 3.0A 1,2,3,4 √ √ √ √ √ - - QFN32
IP5320 3.1A 3.0A Nixie Tube √ √ √ √ √ - - QFN28
IP5506 2.4A 2.1A Nixie Tube √ √ - - - - - ESOP16
IN

IP5508 2.4A 2.1A Nixie Tube √ √ - √ - - - QFN32

IP5330 3.1A 3.0A Nixie Tube √ √ - √ √ - - QFN32
IP5566 3.1A 3.0A 1,2,3,4 √ √ - √ √ - - QFN40
IP5332 18W 4.0A 1,2,3,4 √ √ √ √ √ √ √ QFN32
JO

IP5328P 18W 4.0A 1,2,3,4 √ √ √ √ √ √ √ QFN40

IP5356 22.5W 5.0A Nixie Tube √ √ - √ √ √ √ QFN40
IP5568 22.5W 5.0A Nixie Tube √ √ - √ √ √ √ QFN64
IP5353 22.5W 5.0A 4 √ √ - √ √ √ √ QFN32
IP5389 100W 8.0A Nixie Tube √ √ - √ √ √ √ QFN64
IN

IP5386 45W 8.0A 1,2,4 √ √ - √ √ √ √ QFN48

6.2 IP5353 Common Customized Model Description

IC Part No. Function description
IP5353_AABC Support AABC USB port
IP5353_AACL Support AACL USB port
IP5353_ABCL Support ABCL USB port
IP5353_LSCP_AABC Enable the low-voltage SCP based on IP5353_AABC
IP5353_LSCP_AACL Enable the low-voltage SCP based on IP5353_ AACL

V1.01 Email: [email protected] 6 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
IP5353_LSCP_ABCL Enable the low-voltage SCP based on IP5353_ AACL
IP5353_I2C_AABC Configured as I2C function，support AABC USB port
IP5353_I2C_AACL Configured as I2C function，support AACL USB port

p.
or
C
IC
IN
JO
IN

V1.01 Email: [email protected] 7 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
7 Pin Configuration and Functions

DMA2
DPA2

DMA1
DPA1
CC1
CC2
DMC
DPC
24 23 22 21 20 19 18 17
DPB/DAT 25 16 NTC
DMB/CL 26 15 KEY

p.
VBUS 27 14 BAT
VBUS 28 IP5353 13 VOUT2
VOUT1 29 12 VOUT2
QFN32

or
VOUT1 30 11 VSYS
33 EPAD
VSYS 31 10 VING
LED1 32 9 VIN
1 2 3 4 5 6 7 8

C
LED2
LED3
LX
LX
LX
LX
BST
HLED

Figure 2 IP5353 Top View

IC
7.1 IP5353 Pin Functions
PIN Num PIN Name PIN description
1 LED2 Battery level display drive pin LED2; I2C SDA
IN

Battery level display drive pin LED3; reused as VSETand I2C INT
2 LED3
functions
3、4、5、6 LX DCDC switch node, connect to inductor
7 BST Internal high voltage drive, serial capacitor to LX
JO

8 HLED Fast charge mode indicator

9 VIN VIN power pin
10 VING Used to control input path NMOS of VIN port
11、31 VSYS Public Node of system power input and output
IN

12、13 VOUT2 VOUT2 output port power pin

14 BAT Battery supply pin
15 KEY Key detect pin, reused as WLED torch light function.
16 NTC NTC pin
17 DPA1 VOUT1 port DP pin
18 DMA1 VOUT1 port DM pin
19 DPC VBUS port DP pin
20 DMC VBUS port DM pin

V1.01 Email: [email protected] 8 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
21 CC2 VBUS CC2 pin
22 CC1 VBUS CC1 pin
23 DPA2 VOUT2 port DP pin
24 DMA2 VOUT2 port DM pin
25 DPB/DAT VIN port DP pin or Lightning decoding pin
VIN port DM pin or Lightning port detection and fast charging
26 DMB/CL
communication pin

p.
27、28 VBUS USB Type-C port power pin
29、30 VOUT1 VOUT1 output port power pin

or
32 LED1 Battery level display drive pin LED1; I2C SCK
33 (EPAD) GND GROUND

C
IC
IN
JO
IN

V1.01 Email: [email protected] 9 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
8 Functional Block Diagram

VOUT1 VBUS VOUT2 VIN/

VINUV
LIGHTNING

VINok

IVOUT1 IVBUS IVOUT2 VING

p.
VOUT1 VBUSok VBUSuv VOUT2
Plug in detect Plug in detect
Charge IVOUT1
Pump IVOUT2

Vout2

LED3
LED4
LED5
LED6
Vout1
IVbus

Vbus
VSYS
NTC
BAT
Vin
IVin
BAT BAT Low voltage VSYS

or
detection ADC

DPA1 BST
VOUT1
Output fast charging
DMA1 protocol VSYS HVCC
HVCC LDO
DMC VBUS System
Input and output logic
DPC fast charging Vref/IREF

C
protocol
control

DMA2 HS NMOS
VOUT2 LX
Output fast charging Boost&
DPA2 OTP OSC Charger
protocol
control HVCC
1.5v

CC1
0.9v

CC2 TYPEC &PD

0.4v
OT DECT

VSET_OUT
DMB/CL --
IC
+- LS NMOS
DPB/DAT LED3
LIGHTNING
decoding&VIN input
fast charging Zero CurDet
protocol PEAK CURRENT
GPIO LIMT
LED1 &MFP BAT BAT
I2C interface 20uA 30uA/100uA PGND
LED2
IN

KEY&WLED
LED battery
LED3
level display HLED NTC KEY
JO

Figure 3 Functional Block Diagram

9 Absolute Maximum Ratings

IN

Parameters Symbol Value Unit

Input Voltage Range VIN, VBUS -0.3 ~ 16 V
Junction Temperature Range TJ -40 ~ 150 ℃
Storage Temperature Range Tstg -60 ~ 150 ℃
Thermal Resistance
θJA 35 ℃ /W
(Junction to Ambient)
ESD (Human Body Model) ESD 4 KV
*Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to
the device.

V1.01 Email: [email protected] 10 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
Exposure to Absolute Maximum Rated conditions for extended periods may affect device reliability.

10 Recommended Operating Conditions

Parameter Symbol Min. Typ. Max. Unit

Input Voltage VIN, VBUS 4.5 5 / 9 / 12 13.0 V

Battery Voltage Vbat 3.0 3.7 4.4 V

p.
*Devices’ performance cannot be guaranteed when working beyond those Recommended
Operating Conditions.

or
11 Electrical Characteristics
Unless otherwise specified, TA=25℃, L=2.2μH, VBAT=3.8V
Parameter Symbol Test Conditions Min. Typ. Max. Unit

Input voltage
Input Over
VBUS /VIN

VBUS /VIN C
Charging System

4.5

13.0
5/9/12

13.5
13

14.0
V

V
IC
Voltage
4.20V 4.19 4.22 4.25 V
Constant Charge 4.30V 4.29 4.32 4.35 V
Voltage VTRGT
4.35V 4.34 4.37 4.39 V
IN

4.40V 4.39 4.42 4.45 V

VIN =5V，battery current 2.0 2.4 2.8 A

VIN =9V/12V，battery current 3.8 4.4 5.0 A

JO

Charge Current ICHRG VBUS =5V，input current 2.5 2.8 3.1 A

VBUS =9V，input current 1.7 2.0 2.3 A

VBUS =12V，input current 1.3 1.5 1.7 A

IN

Trickle Charge BAT<2.5V，input current 50 75 100 mA

ITRKL
Current 2.5V<=VBAT<3.0V，input current 100 200 300 mA
Trickle Charge
VTRKL 2.9 3.0 3.1 V
Stop Voltage
Charge Stop
ISTOP 250 400 550 mA
Current
Recharge Voltage
VRCH 4.05 4.10 4.15 V
Threshold
Charge Safety TEND 20 24 27 Hour

V1.01 Email: [email protected] 11 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
Time

Boost System
Battery operation
VBAT 3.0 4.4 V
voltage
VOUT=5V@1A 4.95 5.05 5.15 V
QC2.0 VOUT=9V@1A 8.90 9.10 9.30 V
VOUT

p.
VOUT=12V@1A 11.90 12.10 12.30 V
DC output voltage
QC3.0
@1A 4.95 12.45 V
VOUT
QC3.0

or
200 mV
Step
VBAT=3.7V，VOUT=5.0V，fs=350kHz 100 mV
Output voltage VBAT=3.7V，VOUT=9.0V，fs=350kHz 150 mV
ΔVOUT
ripple

Boost output
VBAT=3.7V ，
fs=350kHz
VOUT=5V
C
VOUT=12.0V ，
200

3.1
mV

A
IC
Iout VOUT=9V 2.22 A
current
VOUT=12V 1.67 A

VBAT=3.7V，VOUT=5V，IOUT=2A 94 %
IN

Boost efficiency ηout VBAT=3.7V，VOUT=9V，IOUT=2A 93 %

VBAT=3.7V，VOUT=12V，IOUT=1.5A 92 %

VBAT=3.7V,VOUT=5V 3.4 4.0 4.4 A

Boost overcurrent
JO

shut down Ishut VBAT=3.7V,VOUT=9V 2.25 2.60 2.90 A

threshold
VBAT=3.7V,VOUT=12V 1.7 1.9 2.2 A
Output light load
Iload VBAT=3.7V 80 mA
shutdown current
Load overcurrent Duration of output voltage under
IN

TUVD 30 ms
detect time 4.2V
Load short circuit Duration of output current above
TOCD 150 200 μs
detect time 4.4A
Control System

Discharge switch frequency 300 350 400 kHz

Switch frequency fs
Charge switch frequency 300 350 400 kHz
NMOS on
rDSON Upper NMOS 9 11 mΩ
resistance

V1.01 Email: [email protected] 12 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
NMOS on
Lower NMOS 9 11 mΩ
resistance
Battery port VIN=0V ， VBAT=3.7V ， average
ISTB 100 μA
standby current current
LED light driving
IWLED 10 15 20 mA
current
IL1 Voltage decrease 10%
LED display
IL2 3 mA

p.
driving current
IL3
Total load Light The load current is consistently
load shut down T1load less than 80mA 25 32 44 s

or
detect time
Output port light
load shut down T2load 14 16 18 s
detect time

C
Short press on
TOnDebounce 60 100 200 ms
key wake up time
Time of WLED
TKeylight 1.2 2 3 s
turn on
IC
Thermal shut
TOTP Rising temperature 130 140 150 ℃
down temperature
Thermal shut
ΔTOTP 40 ℃
down hysteresis
IN
JO
IN

V1.01 Email: [email protected] 13 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
12 Function Description

12.1 Low power lock out and activation

The first time IP5353 access to the battery, IC is in lock out state, battery level indicator LED will flash
5s; Under non-charging state, if the battery voltage is too low to trigger the low power shutdown, IP5353
will enter lock out state too.
In low battery state, to decrease the quiescent power, IP5353 do not support plug in detect function

p.
or key press activation function. During which, key press action will not trigger boost output, and battery
level indicator LED will flash 5s.
Under the lock out state, only by entering charging status can activate IP5353 ‘s full function.

or
12.2 Charge
IP5353 integrated a constant current and constant voltage Li battery charging management system
with synchronous switch, adaptive to various charging voltage.

C
When the battery voltage is lower than 3V, trickle charging less than 200mA charging current is
applied;
when the battery voltage is higher than 3V, enters constant current charging stage, the maximum
charging current at battery port is 5.0A; During 5V input voltage, maximum input power is 10W; During the
fast charging state, maximum input power is 18W. The highest charging current is up to 5.0A, charging
IC
efficiency can be up to 94%, such can reduce 3 / 4 charging time.
when the battery voltage is near the preset battery voltage, enters constant voltage charging stage;
when the charging current is less than 400mA and battery voltage is near the constant voltage charging
stage, the charging process is stopped. When the charging stage is accomplished, once the battery
IN

voltage falls under 4.1V, battery charging stage will be restarted.

IP5353 supports charging the battery and phone at the same time,output voltage is 5V.

12.3 Boost
JO

IP5353 Integrated a synchronized switch converter which supports high voltage output, providing
3.3V ~ 12V output voltage output, load capacity can be: [email protected], [email protected] and [email protected]. 350kHz
switching frequency. Internal soft start function. In avoid of large rush current causing device failure at
start up stage, built-in overcurrent, short circuit, overvoltage and over temperature protection function,
make insurance of the stability and reliability of power system.
IN

Boost system output current can be auto-modulated according to the temperature, ensuring the IC is
under the preset temperature.

V1.01 Email: [email protected] 14 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
IP5353 VOUT=5V Efficiency Curve
100
98
96 3.2V
94
92 3.4V
90
88 3.6V
η(%)

86 3.8V
84

p.
82 4.0V
80
78 4.2V
76
0 500 1000 1500 2000 2500 3000 3500 4000 4500

or
IOUT(mA)

Figure 4 IP5353 VOUT=5V Efficiency Curve

C
IP5353 VOUT=5V V-I Curve
5600
5500
5400 3.2V
5300 3.4V
VOUT(mV)

IC
5200
3.6V
5100
5000 3.8V
4900 4.0V
4800
4.2V
IN

4700
4600
0 500 1000 1500 2000 2500 3000 3500 4000 4500
IOUT(mA)
Figure 5 IP5353 VOUT=5V V-I Curve
JO

IP5353 VOUT=9V Efficiency Curve

100
98
96 3.2V
94
92 3.4V
90
IN

88 3.6V
η(%)

86 3.8V
84
82 4.0V
80
78 4.2V
76
0 500 1000 1500 2000 2500 3000
IOUT(mA)

Figure 6 IP5353 VOUT=9V Efficiency Curve

V1.01 Email: [email protected] 15 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
IP5353 VOUT=9V V-I Curve
9600
9500
9400 3.2V
9300 3.4V
VOUT(mV)

9200
3.6V
9100
9000 3.8V
8900 4.0V

p.
8800
4.2V
8700
8600
0 500 1000 1500 2000 2500 3000
IOUT(mA)

or
Figure 7 IP5353 VOUT=9V V-I Curve

IP5353 VOUT=12V Efficiency Curve

C
100
98
96 3.2V
94
92 3.4V
90
IC
88 3.6V
η(%)

86 3.8V
84
82 4.0V
80
78 4.2V
IN

76
0 500 1000 1500 2000
IOUT(mA)

Figure 8 IP5353 VOUT=12V Efficiency Curve

JO

IP5353 VOUT=12V V-I Curve

12500
12400
12300 3.2V
12200
IN

3.4V
VOUT(mV)

12100
3.6V
12000
11900 3.8V
11800 4.0V
11700
4.2V
11600
11500
0 500 1000 1500 2000
IOUT(mA)

Figure 9 IP5353 VOUT=12V V-I Curve

V1.01 Email: [email protected] 16 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
12.4 USB C
IP5353 integrated USB C DRP port, auto-switching the internal pull-up and pull-down circuit on CC1
and CC2 by distinguishing the role of the attached device. Support Try.SRC function, when the attached
device is also DRP device, IP5353 will supply power for the opposite device.
When worked as DFP, the output current can be set as three levels; when worked as UFP, the current
capability from the opposite device can be detected.

p.
VREG

or
Ip_3P0
VREF1

C
VREF2 CC1/CC2

Rd

VREF3
IC
Figure 10 CC internal circuit

Table 1 Pull-up and pull-down ability

IN

Name Value
Ip_3P0 330μA
Rd 5.1kΩ
JO

Table 2 Comparator Threshold of pull-up Ip

Minimum Voltage Maximum Voltage Threshold
Powered cable/adapter（vRa） 0.00V 0.75V 0.80V
Sink（vRd） 0.85V 2.45V 2.60V
IN

No connect(vOPEN) 2.75V

Table 3 Comparator Threshold of Pull-down Resistor Rd

Detection Min voltage Max voltage Threshold
vRa -0.25V 0.15V 0.20V
vRd-Connect 0.25V 2.04V
vRd-USB 0.25V 0.61V 0.66V
vRd-1.5 0.70V 1.16V 1.23V
vRd-3.0 1.31V 2.04V

V1.01 Email: [email protected] 17 / 37 Copyright © 2022, Injoinic Corp.

 IP5353

p.
or
Figure 11 USB C detects cycle

C
Table 4 USB C detects cycle
Minimum Maximum Description
The period a DRP shall complete a Source to Sink and
tDRP 50ms 100ms
back advertisement
IC
The percent of time that a DRP shall advertise Source
dcSRC.DRP 30% 70%
during tDRP
The time a DRP shall complete transitions between Source
tDRPTransition 0ms 1ms
and Sink roles during role resolution
IN

tDRPTry 75ms 150ms Wait time associated with the Try.SRC state

tDRPTryWait 400ms 800ms Wait time associated with the Try.SNK state
JO
IN

V1.01 Email: [email protected] 18 / 37 Copyright © 2022, Injoinic Corp.

 IP5353

p.
or
C
IC
IN

Figure 11 USB C detects state transition

12.5 USB C PD
JO

IP5353 integrated USB C Power Delivery PD2.0/PD3.0 / PPS (Programmable Power Supply)
protocol, integrate physical (PHY) layer for data transmitting/receiving across the cc wire, hardware
biphase mark coding (BMC) module and hardware CRC protect the data integrity.
Support PD2.0 / PD3.0 bi-directional input/output and PPS output protocol. Input and output voltage
support 5V、9V、12V. Output source cap: [email protected]、 [email protected]、12V @1.67A、PPS 3.3~11V@2A output
IN

voltage adjustable with 20mV / step. Support up to 20W power level.

12.6 Fast Charge Protocol

IP5353 support multi fast charge protocols: PD2.0 / PD3.0 / PPS、QC2.0 / QC3.0、FCP、AFC、Apple、
Samsung.
Input QC2.0/QC3.0 protocol is not support for charging the power bank. External fast charging
protocol IC is not supported.
Input fast charge protocol of FCP、AFC 、PD2.0、PD3.0 are supported for charging the power bank.
If the power bank is to charge for the phone, when IP5353 enter discharge mode, it will detect the fast

V1.01 Email: [email protected] 19 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
charge type and request on DP, DM, which support fast charge for devices of QC2.0/QC3.0、FCP、AFC
and Apple 2.4A mode, Samsung 2.0A mode and BC1.2 1.0A mode.
For Apple 2.4A mode: DP=DM=2.7V
For Samsung 2.0A mode: DP=DM=1.2V
For BC1.2 1.0A mode: DP short to DM
Under BC1.2 mode, when the DP voltage is detected in the range of 2V ~ 0.325V for 1.25s, fast
charge will be initially determined, then the short status between DP and DM will be disconnected, and
DM pull-down 20kOhm to GND at the same time. After which, if in the following 2ms the DP voltage is in

p.
range of 2V ~ 0.325V and DM lower than 0.325V, fast charge handshake is accomplished successfully.
Then QC2.0/QC3.0 device can request for desired voltage according to the QC standards. Any time DP
lower than 0.325V will force to exit the fast charge mode, the ouput voltage will fall back to default 5V.
Table 5 QC2.0/QC3.0 output voltage request rule

or
DP DM Result
0.6V GND 5V
3.3V 0.6V 9V

C
0.6V 0.6V 12V
0.6V 3.3V Continue Mode
3.3V 3.3V Hold
Continuous mode is supported by QC3.0, voltage can be adjusted by 0.2V / step according to QC3.0
IC
request under the continues mode.
Table 6 Fast charging protocol supported by each port of IP5353

protocols VOUT1 output VBUS output VBUS input VOUT2 output VIN input

QC2.0 √ √ - √ -
IN

QC3.0 √ √ - √ -
AFC √ √ √ √ √
FCP √ √ √ √ √
SCP √ √ √ √ √
JO

PD2.0 - √ √ - √
PD3.0 - √ √ - √
PPS - √ - - -
supported: √
not supported: -
IN

12.7 Charge and Discharge Path Management

Standby:
If VIN or VBUS is attached, IP5353 will start the charging process directly.
If USB C UFP device is attached on VBUS or sink device is attached on VOUT port, IP5353 will start
discharge function automatically.
If key is pressed, the VOUT1, VOUT2 and VBUS port will open only when load is detected on the
according port, or the output on these port will be closed.

V1.01 Email: [email protected] 20 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
Discharge:
In the case of no key action, only the output path of the output port plugged in the electrical
equipment will be opened; the output path of the output port not connected to the equipment will not be
opened. When the output current of the opened output port is less than about 80mA, it will automatically
close after a period of time.
Any port of VOUT1, VOUT2 and VBUS can support the output fast charging protocol. However, since
this application is a single inductance application, it can only support one voltage output, so it can only
support the fast charging output when only one output port is open. When two or three outlets are used at

p.
the same time, the quick charge function will be automatically turned off.
According to the connection shown in the "typical application diagram", when any output port has
entered the fast charging output mode, when the other output port is plugged in with electrical equipment,
all the output ports will be closed first, the high-voltage fast charging function will be closed, and then the

or
output ports with equipment will be opened. In this case, all the output ports only support the charging of
apple, Samsung and bc1.2 modes. When the number of electrical equipment is reduced to only one, all
output ports will be closed first, the high-voltage fast charging function will be turned on, and then the

C
output port of the last electrical equipment will be turned on, so as to reactivate the equipment to request
fast charging. When only one output port is open and the total output current is less than about 80mA for
about 32s, the output port and discharge function will be closed and the standby mode will be entered.

Charging:
IC
Any port of VIN port and VBUS port can be charged by inserting the power supply. If both ports are
connected to the power supply for charging, the first inserted power supply will be used for charging.
In the single charging mode, the fast charging mode of the power supply will be automatically
identified, and the appropriate charging voltage and current will be automatically matched
IN

Charging and discharging at the Same Time:

When the charging power supply and the electrical equipment are plugged in at the same time, the
charging and discharging mode will be automatically entered. In this mode, the chip will automatically turn
JO

off the internal fast charge input request. When the vsys voltage is only 5V, turn on the discharge path to
supply power to the electrical equipment; if the vsys voltage is greater than 6.0V, for safety reasons, the
discharge path will not be turned on.
In the process of charging and discharging, if the charging power is unplugged, IP5353 will turn off
the charging function and restart the discharging function to supply power to the electric equipment. For
IN

the sake of safety, and in order to be able to reactivate the mobile phone to request fast charging, the
voltage will drop to 0V for a period of time during the conversion process.
In the process of charging and discharging, if the electric equipment is unplugged, or the electric
equipment is full and stops pumping for 16s, the corresponding discharge path will be automatically
closed. When the discharge paths are closed and the state returns to single charging mode, the charging
undervoltage loop will be reduced, and the fast charging will be automatically reactivated to accelerate the
charging of mobile power supply.

V1.01 Email: [email protected] 21 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
12.8 Automatic Detection of Mobile Phone
Auto detection on sink device / phone attachment:
IP5353 support auto detection on sink device/phone attachment/plug in, once the attachment is
detected, the boost will be turned on charging the sink device / phone, so non-key solution are supported.
Auto detection on sink device / phone fully charged:
When the output current of a single port is less than about 80mA and lasts for about 16s, the output
port will be closed. When the total current is less than about 80mA for about 32s, it is considered that all

p.
output cell phones are full or unplugged, and the boost output will be automatically turned off.

12.9 KEY

or
KEY

WLED

Figure 13 KEY circuit

C
IC
Key circuit is illustrated in Figure 13, which can recognize short press or long press operation.
 Short press : pressed time in range of 100ms~2s：turn on the battery level display LED and
BOOST output
 Long press :pressed time longer than 2s：turn on or turn off the torch light WLED
IN

 No response on press time less than 30ms

 Two short press in 1s: turn off boost output, battery level display LED and torch light WLED
 Long 10s press will reset the whole system

12.10 Fast Charge State Indication

JO

HLED PIN is used for indication for the present fast charge mode, either in fast charging or
discharging mode, when the system enters fast charge , the light LED will turn on.

HLED
IN

RVTHS

Figure 14 fast charge state indication

12.11 Selection of Battery Charge Discharge Curve

IP5353 selects different battery charging and discharging curves by pulling down the resistors with
different resistance values (RVTHS) on the HLED pin. The connection mode is shown in Figure 14.
The following table lists the relationship between the state of power indicator and battery voltage

V1.01 Email: [email protected] 22 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
when RVTHS with different resistance values are pulled down at HLED pin;
It should be noted that the rotating lamp voltage (OCV) in the table is not the actual voltage of the
battery, but the voltage after compensation of the internal resistance of the battery. The calculation
formula is as follows:
During charging, turn lamp voltage (OCV) = actual battery voltage (voltage from IP5353 BAT (14th
pin) to ground) - IBAT (battery terminal charging current measured by IP5353) * RSET (40mΩ);
When discharging, turn lamp voltage (OCV) = actual battery voltage (voltage from IP5353 BAT (14th
pin) to ground) + IBAT (battery terminal discharge current measured by IP5353) * RSET (40mΩ);

p.
Table 7 Charge discharge OCV threshold
Battery charging and Charge and discharge
Power Indicator
Resistance discharging voltage rotating lamp voltage
Status
(4.20V) (4.30V/4.35V/4.40V battery)

or
4 lights to 3 lights 4020 mV 4020 mV
1 20kΩ 1% 3 lights to 2 lights 3780 mV 3780 mV
2 lights to 1 lights 3600 mV 3600 mV

C
4 lights to 3 lights 4020 mV 4020 mV
2 43kΩ 1% 3 lights to 2 lights 3900 mV 3900 mV
2 lights to 1 lights 3660 mV 3660 mV
4 lights to 3 lights 4020 mV 4020 mV
IC
2 62kΩ 1% 3 lights to 2 lights 3900 mV 3900 mV
2 lights to 1 lights 3780 mV 3780 mV
4 lights to 3 lights 3900 mV 4020 mV
NC
4 3 lights to 2 lights 3720 mV 3900 mV
（Register setting）
IN

2 lights to 1 lights 3600 mV 3720 mV

12.12 Battery Level Display

Battery level display for LED mode
JO

IP5353 4LED battery level display solution, the connection method is as follows.

LED3
IN

VSET
LED2
100Ω

D1 D2 D3 D4
LED1
100Ω
4LED Mode

Figure 15 4LED circuits

V1.01 Email: [email protected] 23 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
4LED display mode:
Table 8 Charging lamp display
Battery capacity (C) (%) D1 D2 D3 D4

Fully charged ON ON ON ON

75%≤C ON ON ON 0.5Hz Flash

50%≤C<75% ON ON 0.5Hz Flash OFF

p.
25%≤C<50% ON 0.5Hz Flash OFF OFF

C<25% 0.5Hz Flash OFF OFF OFF

or
Table 9 Boost lamp display
Battery capacity (C) (%) D1 D2 D3 D4

C≥75% ON ON ON ON

C
50%≤C<75% ON ON ON OFF

25%≤C<50% ON ON OFF OFF

3%≤C<25% ON OFF OFF OFF

IC
0%<C<3% 1.0Hz Flash OFF OFF OFF

C=0% OFF OFF OFF OFF

IN

12.13 Abnormal prompt

IP5353 supports abnormal light display. When abnormal conditions such as NTC high and low
temperature, VIN/VBUS overvoltage, and BAT low power are triggered, the power indicator light will
alarm.
JO

Table 10 Boost lamp display

Abnormal state D1 D2 D3 D4
NTC high temperature /
1.25Hz Flash 1.25Hz Flash 1.25Hz Flash 1.25Hz Flash
NTC low temperature
VIN/VBUS overvoltage 1.25Hz Flash 1.25Hz Flash 1.25Hz Flash 1.25Hz Flash
IN

1.25Hz Flash
BAT low voltage OFF OFF OFF
4 times

12.14 VSET（Battery voltage selection）

IP5353 can set battery specifications and configure parameters of different battery specifications
through VSET pin (LED3 pin). The resistance threshold of VSET and the set battery specifications are
shown in the table below.

V1.01 Email: [email protected] 24 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
Table 11 Battery voltage selection
Resistance Battery Type
NC 4.20V
68kΩ 4.30V
33kΩ 4.35V
10kΩ 4.40V

p.
12.15 NTC function
IP5353 integrates NTC function, which can detect battery temperature. When IP5353 is working,
NTC pin output current, and generate voltage through external NTC resistance. IC internal detects the

or
voltage of NTC pin to determine the current battery temperature.
* The 100nF capacitance of NTC must be close to IC PIN.

NTC_ADC
30μA/100μA NTC

C
ADC

RNTC=10kΩ@25℃ C1 100nF
B=3380
IC
Figure 16 NTC circuit

NTC放出电流
IN

100μA
JO

30μA
0.3V 1.5V

NTC PIN电压

Figure 17 Relationship between NTC voltage and output current

IN

When the NTC discharge current is 80μA, if the NTC voltage is higher than 1.5V, the current
becomes 30μA;
When the NTC discharge current is 30μA, if the NTC voltage is lower than 0.3V, the current changes
to 100μA.
In the state of charge:
When the NTC voltage is lower than 0.49V, it means the battery temperature is higher than 45℃，
the charging is stopped.
When the NTC voltage is higher than 0.82V, it means the battery temperature is lower than 0℃，the
charging is stopped.
In the state of discharge:

V1.01 Email: [email protected] 25 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
When the NTC voltage is lower than 0.30V, it means the battery temperature is higher than 60℃，the
discharging is stopped.
When the NTC voltage is higher than 2.08V, it means the battery temperature is lower than -20℃，the
discharging is stopped.
If NTC is not required in the application, 10kΩ resistance shall be connected to the ground at NTC pin,
and floating or direct grounding is not allowed.

12.16 I2C

p.
I2C connection mode
LED3 INT

510kΩ

or
SDA 3.3kΩ
LED2 VBAT

SLK 3.3kΩ
LED1 VBAT

Figure 18 I2C Application method

C
The IP5353 does not support I2C connection by default. If the I2C connection is required, the
customized IP5353_I2C_XXXX is used for design. In I2C mode, the INT signal is in high resistance state
IC
in standby mode and high level state in working state, which can be used to wake up MCU.

12.17 Apple lightning line communication

IN

IP5353 integrated lightning communication circuit, external connection mode is shown in Figure 19.
Since the communication circuit needs to be pulled up to bat through an external 510Ω resistor, the
communication can be successful only when the battery voltage is above 3V. If the communication can
succeed when the battery voltage is lower than 3V, it is recommended to add lightning communication
JO

chip.

6 VIN 9 VIN

C2
2.2μF
VING
IN

BAT
LIGHT DAT
5 R1
NING 510Ω
DAT1 25
9 DAT
R2
3kΩ
USB2

Figure 19 Lightning communication circuit

V1.01 Email: [email protected] 26 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
13 PCB Layout
Here below lists essential precautions that may affect the function and performance on PCB layout,
more details will be attached in another document if any.

13.1 Location of VOUT1 / VOUT2 / VBUS capacitor

IP5353 integrated USB output power path, VOUT1 / VOUT2 / VBUS 2.2μF capacitor must be placed
close to the chip pin. If the layout allows, the closer the capacitor is to the chip, the better.

p.
At the same time, place a 100nF capacitor close to the USB seat, and the capacitor is close to the
USB seat in parallel.

or
C
IC
Figure 20 Output capacitance

13.2 Location of VSYS capacitor

IN

The power and current of the chip are relatively large, and the position of the capacitor on the VSYS
network will affect the stability of the DCDC. The capacitors on the VSYS network need to be as close to
the VSYS pin and EPAD of the IC as possible, and copper is laid on a large area, and more vias are
added to reduce the area of current loop between the capacitors and the IC and reduce parasitic
JO

parameters.
VSYS pins are distributed on both sides of the chip, and capacitors need to be placed near the pins
on both sides, and the VSYS pins on both sides are connected by a wide (no less than 100mil) copper
laying on the PCB.
IN

Figure 21 VSYS capacitance

V1.01 Email: [email protected] 27 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
13.3 Location of BAT/NTC capacitor
The filter capacitors of BAT pin and NTC pin should be placed as close as possible to the pin of the
chip, and some holes should be drilled near the capacitors GND pin.

p.
or
Figure 22
C
BAT/NTC capacitance
IC
IN
JO
IN

V1.01 Email: [email protected] 28 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
14 Typical Application Diagram
Total solution of fast charge power bank is merely realized by passive devices of MOSFET, inductor,
capacitor and resistor.

14.1 IP5353_AABC

49
27
VBUS

p.
VBUS 28 GND
VBUS EPAD
DMC 19 15 R1 10kΩ K1
DPC DPC KEY
C8 C6 20
TYPE-C CC1 100nF 2.2μF
DMC
21 D6
CC2 CC2
22 R2 20Ω
GND CC1

or
8
R3 100Ω D5
USB2
HLED
12
VOUT2 13 VOUT2 R7 NC
DMA2
VOUT2
23
USB-A DPA2 DPA2
C9 C5 24
GND DMA2 R4 NC
100nF 2.2μF

C
USB3
D4
100%
D3
VOUT1
29
30 VOUT1 IP5353 75%
VOUT1 U1
DMA1 17
USB-A DPA1 DPA1 D2
C10 C4 18
IC
GND DMA1 50%
100nF 2.2μF
2
LED3
USB4 D1
25%
1
VIN 9 LED2
VIN R5 100Ω
DMB 25
Micro- C7 32
B DPB DPB/DAT LED1
2.2μF 26
GND DMB/CL R6 100Ω
IN

10
N1
VING RNTC 10kΩ@25℃
USB1 AO3400
NMOS 11 16 B=3380
VSYS
31 NTC
VSYS VSYS

C3 100nF
Note 3： CP8 CP7 CP6 CP5 CP4
220μF 22μF 22μF 22μF 22μF
BAT BST LX LX LX LX
L1
JO
14

2.2μH
6
5

3
7

C2
100nF
BAT
C1
100nF CP1 CP2 CP3
22μF 22μF 22μF
IN

Figure 23 IP5353_AABC application circuit

Note:
1、C3 capacitor needs to be close to NTC pin. When NTC is not used, NTC pin is grounded through
10kΩ resistance;
2、When VIN port is not required, it can be directly suspended; When VOUT1 or VOUT2 ports are not
required, the 2.2μF capacitor needs to be kept close to the chip pin.
3、IP5353 VSYS 220μF capacitor: VSYS capacitor needs to be close to the chip pin, if the capacitor is
too far to add 220μF electrolytic capacitor. If the structure allows, we suggest adding 220μF electrolytic
capacitor. If no electrolytic capacitor is added, the VSYS capacitor should be close to the chip pin.
4、If the solution has only A+A+C USB port, IP5353_AABC is recommended.

V1.01 Email: [email protected] 29 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
BOM
No. Part Name Type Location Num Note
1 SMT IC QFN32 IP5353 U1 1
SMT capacitor 0603 100nF 10%
2 C1 1
16V
SMT capacitor 0603 100nF 10%
3 C2 C8 C9 C10 4
25V
SMT capacitor 0603 2.2μF 10%

p.
4 C4 C5 C6 C7 4
25V
5 SMT capacitor 0805 22μF 10% 16V CP1 CP2 CP3 3
6 SMT capacitor 0805 22μF 10% 25V CP4 CP5 CP6 CP7 4

or
7 capacitor 220uf 10% 25V CP8 1
8 SMT resistor 0603 10kΩ 1% R1 2
9 SMT resistor 0603 NC 1% R4 R7 2
10 SMT resistor 0603 100Ω 1% R3 R5 R6 3

C
11 SMT LED 0603 BLUE D1 D2 D3 D4 4
12 SMT LED 0603 RED D5 1
13 LED 5MM LED D6 1
14 SMT resistor 0603 20Ω 1% R2 1
IC
10kΩ@25℃
15 NTC RNTC 1
B=3380
0603 100nF 10%
16 SMT capacitor C3 1
16V
IN

17 SMT NMOS SOT23-3 AO3400 N1 1

18 Inductor 2.2μH 10*10 L1 1
19 KEY SMT 3*6 K1 1
20 OUTPUT USB AF10 8 USB USB3 USB4 2
JO

USB C USB C
21 USB2 1
CONNECTOR CONNECTOR
22 INPUT USB MICRO-7-DIP-5.9 USB1 1

Recommended inductance model

Heat
IN

DC Saturation
Rating
Thickness Inductance Resistance Current Measuring
DARFON PIN Tolerance Current
(mm) (μH) (mΩ) DC Amps. Condition
DC Amp.
Max. Idc(A)Max. Isat(A)Max.
SPA1040-2R2M 4.0 2.2 ±20% 7.0 14.0 16.0 100kHz/1.0V

V1.01 Email: [email protected] 30 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
14.2 IP5353_AACL

49
27
VBUS GND
VBUS 28
VBUS EPAD
DMC 19
DPC DPC
C8 C6 20
TYPE-C CC1 100nF 2.2μF
DMC
21
CC2 CC2
22
GND CC1

p.
USB2 R1 10kΩ
12 15 K1
13
VOUT2 KEY
VOUT2
DMA2
VOUT2
23 D6
USB-A DPA2 DPA2
C9 C5 24 R2 20Ω
GND DMA2
100nF 2.2μF

or
8
R3 100Ω D5
USB3
HLED
29
VOUT1 30
VOUT1
VOUT1 R7 NC
DMA1 17
USB-A DPA1 DPA1
C10 C4 18
GND DMA1
100nF 2.2μF
R4 NC

C
USB4

IP5353 D4
VIN U1 100%
6
DAT1 D3
5 BAT
DAT2 75%
9
LIGHTING R8
8 DMB/CL
510Ω
IC
D2
1 GND DPB/DAT
0 50%
1 GND R9 2
2 GND 3kΩ LED3
D1
25
USB1 DPB/DAT 25%
26
DMB/CL 1
9 LED2
VIN R5 100Ω
C7 32
LED1
IN

2.2μF
10 R6 100Ω
VING
AO3400 N1 RNTC 10kΩ@25℃
NMOS 11 16 B=3380
VSYS
31 NTC
VSYS VSYS

C3 100nF
Note 3： CP8 CP7 CP6 CP5 CP4
220μF 22μF 22μF 22μF 22μF
JO

BAT BST LX LX LX LX
L1
14

2.2μH
6
5

3
7

C2
100nF
BAT
C1
100nF CP1 CP2 CP3
22μF 22μF 22μF
IN

Figure 24 IP5353_AACL application circuit

Note:
1、C3 capacitor needs to be close to NTC pin. When NTC is not used, NTC pin is grounded through
10kΩ resistance;
2、When VIN port is not required, it can be directly suspended; When VOUT1 or VOUT2 ports are not
required, the 2.2μF capacitor needs to be kept close to the chip pin.
3、IP5353 VSYS 220μF capacitor: VSYS capacitor needs to be close to the chip pin, if the capacitor is
too far to add 220μF electrolytic capacitor. If the structure allows, we suggest adding 220μF electrolytic
capacitor. If no electrolytic capacitor is added, the VSYS capacitor should be close to the chip pin.

V1.01 Email: [email protected] 31 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
BOM
No. Part Name Type Location Num Note
1 SMT IC QFN32 IP5353 U1 1
SMT capacitor 0603 100nF 10%
2 C1 1
16V
SMT capacitor 0603 100nF 10%
3 C2 C8 C9 C10 4
25V
SMT capacitor 0603 2.2μF 10%

p.
4 C4 C5 C6 C7 4
25V
5 SMT capacitor 0805 22μF 10% 16V CP1 CP2 CP3 3
6 SMT capacitor 0805 22μF 10% 25V CP4 CP5 CP6 CP7 4

or
7 capacitor 220uf 10% 25V CP8 1
8 SMT resistor 0603 10kΩ 1% R1 2
9 SMT resistor 0603 NC 1% R4 R7 2
10 SMT resistor 0603 100Ω 1% R3 R5 R6 3

C
11 SMT LED 0603 BLUE D1 D2 D3 D4 4
12 SMT LED 0603 RED D5 1
13 LED 5MM LED D6 1
14 SMT resistor 0603 20Ω 1% R2 1
IC
10kΩ@25℃
15 NTC RNTC 1
B=3380
0603 100nF 10%
16 SMT capacitor C3 1
16V
IN

17 SMT NMOS SOT23-3 AO3400 N1 1

18 inductor 2.2μH 10*10 L1 1
19 KEY SMT 3*6 K1 1
20 OUTPUT USB AF10 8 USB USB3 USB4 2
JO

USB C USB C
21 USB2 1
CONNECTOR CONNECTOR
22 INPUT USB LIGHTNING USB1 1
23 SMT resistor 0603R 510Ω 1% R8 1
24 SMT resistor 0603R 3kΩ 1% R9 1
IN

Recommended inductance model

Heat
DC Saturation
Rating
Thickness Inductance Resistance Current Measuring
DARFON PIN Tolerance Current
(mm) (μH) (mΩ) DC Amps. Condition
DC Amp.
Max. Idc(A)Max. Isat(A)Max.
SPA1040-2R2M 4.0 2.2 ±20% 7.0 14.0 16.0 100kHz/1.0V

V1.01 Email: [email protected] 32 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
14.3 IP5353_ABCL

49
27
VBUS GND
VBUS 28
VBUS EPAD
DMC 19
DPC DPC
C8 C6 20
TYPE-C CC1 100nF 2.2μF
DMC
21
CC2 CC2
22
GND CC1

p.
USB2 R1 10kΩ
12 15 K1
VOUT2 KEY
VOUT2 13
DMB
VOUT2
MICRO- 23 D6
DPB
DPB DPA2
B C5 R2 20Ω
GND 2.2μF DMB 24
DMA2
8
R3 100Ω D5
USB3
HLED

or
29
VOUT1 30
VOUT1
VOUT1 R7 NC
DMA1 17
USB-A DPA1 DPA1
C10 C4 18
GND DMA1
100nF 2.2μF
R4 NC
USB4

IP5353

C
D4
VIN U1 100%
6
DAT1 D3
5 BAT
DAT2 75%
9
LIGHTING R8
8 CL 510Ω D2
GND DAT
10 50%
1 GND R9 2
IC
2
GND 3kΩ LED3
25 D1
DAT DPB/DAT
USB1 25%
26
CL DMB/CL 1
9 LED2
VIN R5 100Ω
C7 32
2.2μF LED1
10 R6 100Ω
VING
N1 RNTC 10kΩ@25℃
IN

AO3400
NMOS 11 16 B=3380
VSYS
31 NTC
VSYS VSYS

Note 3： C3 100nF
CP8 CP7 CP6 CP5 CP4
220μF 22μF 22μF 22μF 22μF
BAT BST LX LX LX LX
L1
14

2.2μH
6
5

3
7

4
JO

C2
100nF
BAT
C1
100nF CP1 CP2 CP3
22μF 22μF 22μF

Figure 25 IP5353_ABCL application circuit

IN

Note:
1、C3 capacitor needs to be close to NTC pin. When NTC is not used, NTC pin is grounded through
10kΩ resistance;
2、When VIN port is not required, it can be directly suspended; When VOUT1 or VOUT2 ports are not
required, the 2.2μF capacitor needs to be kept close to the chip pin.
3、IP5353 VSYS 220μF capacitor: VSYS capacitor needs to be close to the chip pin, if the capacitor is
too far to add 220μF electrolytic capacitor. If the structure allows, we suggest adding 220μF electrolytic
capacitor. If no electrolytic capacitor is added, the VSYS capacitor should be close to the chip pin.
4、If there is only A+B+C USB port in the scheme, IP5353_ABCL model is recommended, and the
MOS tube with external expansion can be omitted to save cost.

V1.01 Email: [email protected] 33 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
BOM
No. Part Name Type Location Num Note
1 SMT IC QFN32 IP5353 U1 1
SMT capacitor 0603 100nF 10%
2 C1 1
16V
SMT capacitor 0603 100nF 10%
3 C2 C8 C10 4
25V
SMT capacitor 0603 2.2μF 10%

p.
4 C4 C5 C6 C7 4
25V
5 SMT capacitor 0805 22μF 10% 16V CP1 CP2 CP3 3
6 SMT capacitor 0805 22μF 10% 25V CP4 CP5 CP6 CP7 4

or
7 capacitor 220uf 10% 25V CP8 1
8 SMT resistor 0603 10kΩ 1% R1 2
9 SMT resistor 0603 NC 1% R4 R7 2
10 SMT resistor 0603 100Ω 1% R3 R5 R6 3

C
11 SMT LED 0603 BLUE D1 D2 D3 D4 4
12 SMT LED 0603 RED D5 1
13 LED 5MM LED D6 1
14 SMT resistor 0603 20Ω 1% R2 1
IC
10kΩ@25℃
15 NTC RNTC 1
B=3380
0603 100nF 10%
16 SMT capacitor C3 1
16V
IN

17 SMT NMOS SOT23-3 AO3400 N1 1

18 inductor 2.2μH 10*10 L1 1
19 KEY SMT 3*6 K1 1
20 OUTPUT USB AF10 8 USB USB4 1
JO

USB C USB C
21 USB2 1
CONNECTOR CONNECTOR
22 INPUT USB MICRO-7-DIP-5.9 USB3 1
23 INPUT USB LIGHTNING USB1 1
24 SMT resistor 0603R 510Ω 1% R8 1
25 SMT resistor 0603R 3kΩ 1% R9 1
IN

Recommended inductance model

Heat
DC Saturation
Rating
Thickness Inductance Resistance Current Measuring
DARFON PIN Tolerance Current
(mm) (μH) (mΩ) DC Amps. Condition
DC Amp.
Max. Idc(A)Max. Isat(A)Max.
SPA1040-2R2M 4.0 2.2 ±20% 7.0 14.0 16.0 100kHz/1.0V

V1.01 Email: [email protected] 34 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
15 Package

15.1 Package of the Chip

p.
or
C
IC
MILLIMETER
SYMBOL
MIN NOM MAX
A 0.70 0.75 0.80
IN

A1 - 0.02 0.05
b 0.15 0.20 0.25
c 0.18 0.20 0.25
D 7.90 8.0 8.10
JO

D2 6.10 6.20 6.30

e 0.4 BSC
Nd 6.00BSC
E 7.90 8.0 8.10
E2 6.10 6.20 6.30
IN

Ne 6.00BSC
L 0.45 0.50 0.55
K 0.20 - -
h 0.30 0.35 0.40

Figure 26 package

V1.01 Email: [email protected] 35 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
15.2 Marking Description

IP5353

p.
XXXXXXXX

or
Note：
1、 --Injoinic Logo
2、IP5353 --Part Number
3、XXXXXXXX --Manufacture number

C
4、 --PIN1 location

Figure 27 Marking description

IC
IN
JO
IN

V1.01 Email: [email protected] 36 / 37 Copyright © 2022, Injoinic Corp.

 IP5353
16 IMPORTANT NOTICE
INJOINIC TECHNOLOGY and its subsidiaries reserve the right to make corrections, enhancements,
improvements and other changes to its semiconductor products and services. Buyers should obtain the
latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to
INJOINIC TECHNOLOGY's terms and conditions of sale supplied at the time of order acknowledgment.
INJOINIC TECHNOLOGY assumes no liability for applications assistance or the design of Buyers'

p.
products. Buyers are responsible for their products and applications using INJOINIC TECHNOLOGY's
components. To minimize the risks associated with Buyers' products and applications, Buyers should
provide adequate design and operating safeguards.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory

or
and safety-related requirements concerning its products, and any use of INJOINIC TECHNOLOGY's
components in its applications, notwithstanding any applications-related information or support that may
be provided by INJOINIC TECHNOLOGY. Buyer represents and agrees that it has all the necessary

C
expertise to create and implement safeguards which anticipate dangerous consequences of failures,
monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take
appropriate remedial actions. Buyer will fully indemnify INJOINIC TECHNOLOGY and its representatives
against any damages arising out of the use of any INJOINIC TECHNOLOGY's components in
safety-critical applications.
IC
Reproduction of significant portions of INJOINIC TECHNOLOGY's information in INJOINIC
TECHNOLOGY's data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. INJOINIC TECHNOLOGY
is not responsible or liable for such altered documentation. Information of third parties may be subject to
IN

additional restrictions.
INJOINIC TECHNOLOGY will update this document from time to time. The actual parameters of the
product may vary due to different models or other items. This document voids all express and any implied
warranties.
JO

Resale of INJOINIC TECHNOLOGY's components or services with statements different from or

beyond the parameters stated by INJOINIC TECHNOLOGY for that component or service voids all
express and any implied warranties for the associated INJOINIC TECHNOLOGY's component or service
and is an unfair and deceptive business practice. INJOINIC TECHNOLOGY is not responsible or liable for
any such statements.
IN

V1.01 Email: [email protected] 37 / 37 Copyright © 2022, Injoinic Corp.